-
COMMERCIAL CEMENT PLASTER 2
™
DS825
Fiberglass Reinforced Portland Cement Plaster
Applied to Metal or Wood Framed Walls
Commercial Cement Plaster 2 Installation Details
-
TABLE OF CONTENTS
Termination at Storefront Window - Jamb
Termination at Self Flashing Nail-On Window
Termination at Wood WindowCCP 2 Cutaway
DETAIL PAGE
CCP-2 0.0.01CCP-2 0.0.02CCP-2 0.0.03
DRYVIT MAKES NO REPRESENTATION REGARDING CONFORMITY OFITS SUGGESTIONS TO MODEL BUILDING CODES, ENGINEERINGCRITERIA, SPECIFIC APPLICATIONS OR PROJECT LOCATIONS. ALLCOMPONENTS INDICATED IN ILLUSTRATIONS, AS WELL ASOTHERS THAT MAY BE REQUIRED FOR THE INTEGRITY OF THESYSTEM SHALL BE DESIGNED, DETAILED AND ENGINEERED BYREPRESENTATIVES OF THE ARCHITECT, OWNER OR CONTRACTORTO BE IN CONFORMANCE WITH MODEL CODES, ARCHITECTURALAND ENGINEERING REQUIREMENTS PERTAINING TO SPECIFICBUILDING PROJECTS.
DRYVIT MAKES NO WARRANTY, EXPRESSED OR IMPLIED, AS TOTHE ARCHITECTURAL DESIGN, ENGINEERING, OR WORKMANSHIP OFPROJECTS UTILIZING DRYVIT SYSTEMS OR PRODUCTS.
THE LIABILITIES OF DRYVIT SHALL BE AS STATED IN THEDRYVIT STANDARD WARRANTY. CONTACT DRYVIT FOR A FULLAND COMPLETE COPY OF THIS WARRANTY.
NOTE
CCP-2 0.0.04
Termination at Storefront Window - Head + Sill
CCP-2 0.0.05
Termination at Storefront Window - Setback
CCP-2 0.0.06
Termination at Concrete Foundation
CCP-2 0.0.07
Outside Corner CCP-2 0.0.08Inside Corner Detail CCP-2 0.0.09Horizontal Flashing & Expansion Joint
CCP-2 0.0.10
Termination at Roof CCP-2 0.0.11Termination at Roof/Wall Intersection
CCP-2 0.0.12
Termination at Parapet/Wall Intersection
CCP-2 0.0.13
Parapet Flashing CCP-2 0.0.14Soffit With Continuous Vent CCP-2 0.0.15Soffit/Fascia Intersection CCP-2 0.0.16EPS Cornice CCP-2 0.0.17Expansion Joint Intersection CCP-2 0.0.18Horizontal or Vertical Expansion Joint
CCP-2 0.0.19
Termination at EIFS/Lap Siding CCP-2 0.0.20Two-Piece Horizontal Expansion Joint CCP-2 0.0.21Pipe Railing Attachment CCP-2 0.0.22Hose Bib Penetration CCP-2 0.0.23Sloped Sill CCP-2 0.0.24
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
-
CCP 2 CUTAWAY
™
SHEATHED FRAMING
SUBSTRATE
CCP-2 0.0.01
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
AutoCAD SHX TextFRAMING MEMBERS (BY OTHERS)
AutoCAD SHX TextSHEATHING BOARD (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)(NOTE 2)
AutoCAD SHX TextDRYVIT FINISH
AutoCAD SHX TextDRYVIT PRIMER
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
-
CCP-2 0.0.02
Termination at Wood Window
™
HEAD
JAMB
SILL
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
AutoCAD SHX TextHEAD FLASHING WITH END DAMS (BY OTHERS)
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextWOOD WINDOW (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE NOTE 2)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextBACKER ROD AND SEALANT (BY OTHERS)
AutoCAD SHX TextWOOD WINDOW (BY OTHERS)
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
AutoCAD SHX TextBACKER ROD AND SEALANT (BY OTHERS)
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX Text12MM (1/2 IN) MIN. TYP.
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextSILL FLASHING W/END DAMS (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
-
CCP-2 0.0.03
™
HEAD & JAMB
SILL
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™NOTE:
1. ALTERNATE DETAIL AT WINDOWHEAD WOULD INCLUDE METALFLASHING WITH END DAMS
2. ADDITIONAL FLASHING MAY BEREQUIRED FOR WINDOWS THATARE NOT SELF FLASHING
3. BUILDING CODES REQUIRE 2LAYERS OVER WOOD BASEDSUBSTRATES. COMPLY WITH ALLLOCAL CODE REQUIREMENTS.
4. OTHER APPROVED SCRATCH ANDBROWN COATS MAY BEACCEPTABLE. CONSULT DRYVITSYSTEMS, INC. FOR SPECIFICS.
Termination at
Self Flashing Nail-On Window
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 4)(NOTE 4)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 3)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 3)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
AutoCAD SHX TextCASING BEAD WITH WEEPS, (BY OTHERS)
AutoCAD SHX TextBACKER ROD AND SEALANT (BY OTHERS) (PROVIDE WEEPS AT HEAD)
AutoCAD SHX TextSELF FLASHING WINDOW (BY OTHERS)
AutoCAD SHX TextSELF FLASHING WINDOW (BY OTHERS)
AutoCAD SHX TextBACKER ROD AND SEALANT (BY OTHERS)
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 3)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 3)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX Text12MM (1/2 IN) MIN. TYP.
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 4)
-
CCP-2 0.0.04
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™ Termination atStorefront Window-Jamb
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextSTOREFRONT WINDOW (BY OTHERS)
AutoCAD SHX TextBACKER ROD AND SEALANT (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX Text12MM (1/2 IN) MIN.
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
-
CCP-2 0.0.05
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™ Termination atStorefront Window-Head+Sill
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)(NOTE 2)
AutoCAD SHX TextCASING/DRIP REVEAL WITH WEEPS (BY OTHERS)
AutoCAD SHX TextSTOREFRONT WINDOW (BY OTHERS)
AutoCAD SHX TextDRIP FLASHING w/END DAMS (BY OTHERS)
AutoCAD SHX TextBACKER ROD AND SEALANT (BY OTHERS)
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX Text26MM (1 IN) MIN.
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
-
CCP-2 0.0.06
HEAD & JAMB
SILL
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™ Termination atStorefront Window Setback
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
® ™
AutoCAD SHX TextSEE SILL DETAIL
AutoCAD SHX TextSEE HEAD DETAIL
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)(NOTE 2)
AutoCAD SHX TextTREATED WOOD NAILER AND PLASTER STOP (BY OTHERS)
AutoCAD SHX TextCORNER BEAD (BY OTHERS)
AutoCAD SHX TextBACKER ROD AND SEALANT (BY OTHERS)
AutoCAD SHX TextALUMINUM SHIM BLOCK (BY OTHERS)
AutoCAD SHX Text77MM (3 in) MIN.
AutoCAD SHX TextSTOREFRONT WINDOW (BY OTHERS) INSTALLED AFTER CEMENT PLASTER APPLICATION
AutoCAD SHX TextMETAL FLASHING w/ END DAMS (BY OTHERS)
AutoCAD SHX TextALUMINUM SHIM BLOCK (BY OTHERS)
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextOPENING WRAP (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT DEMANDIT® OR COLOR PRIME OR COLOR PRIME ON SURFACES TO RECEIVE SEALANT
AutoCAD SHX TextFLASHING (BY OTHERS)
AutoCAD SHX Text13MM (1/2 in) MIN. TYP.
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
-
CCP-2 0.0.07
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™ Termination atConcrete Foundation
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
CASING BEAD AT CONCRETE FOUNDATION
WEEP SCREED AT CONCRETE FOUNDATION
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2) (NOTE 2)
AutoCAD SHX TextFLASHING SET IN SEALANT (BY OTHERS)
AutoCAD SHX TextFOUNDATION WALL (BY OTHERS)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextFRAMING MEMBER
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextFOUNDATION WEEP SCREED (BY OTHERS)
AutoCAD SHX TextFOUNDATION WALL (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 1)
-
CCP-2 0.0.08
Outside Corner
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1), BEND AROUND CORNER ATTACHED TIGHT AGAINST CORNER SUBSTRATE. EXTEND LATH 610MM (24 IN) PAST CORNER
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2) (NOTE 2)
AutoCAD SHX TextCORNER BEAD (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
-
CCP-2 0.0.09
Inside Corner Detail
INSIDE CORNER
INSIDE CORNER CONTROL JOINT
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX Text203MM (8 in)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1), BEND AROUND CORNER ATTACHED TIGHT AGAINST CORNER SUBSTRATE. EXTEND LATH 610MM (24 in) PAST CORNER
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX Text#30 CONTROL JOINT (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)(NOTE 2)
-
CCP-2 0.0.10
Horizontal Flashing & Expansion Joint
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)(NOTE 2)
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
AutoCAD SHX TextCONTINUOUS METAL FLASHING (BY OTHERS)
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
-
CCP-2 0.0.11
Termination at Roof
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX Text 203 MM (8 IN) MIN
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2) (NOTE 2)
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
AutoCAD SHX TextROOFING PAPER EXTENDED OVER SHEATHING (BY OTHERS)
AutoCAD SHX TextMETAL ROOF FLASHING (BY OTHERS)
AutoCAD SHX TextROOFING (BY OTHERS)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
AutoCAD SHX TextROOFING MEMBRANE (BY OTHERS)
AutoCAD SHX TextROOFING TILES (BY OTHERS)
AutoCAD SHX TextMETAL VALLEY FLASHING PAN LAP OVER ROOFING MEMBRANE (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
-
CCP-2 0.0.12
Termination at Roof/Wall Intersection
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextWATER TIGHT DIVERTER SEAMS (TYPICAL)
AutoCAD SHX TextDIVERTER FLASHING (BY OTHERS)
AutoCAD SHX Text110° MIN.
AutoCAD SHX Text76MM (3 in)
AutoCAD SHX Text305MM (12 in)
AutoCAD SHX Text153MM (6 in)
AutoCAD SHX Text6 in
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2) (NOTE 2)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX Text51MM (2 in) MIN.
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDIVERTER FLASHING (BY OTHERS)
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
-
CCP-2 0.0.13
Termination at Parapet/Wall Intersection
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX Text(6 in)
AutoCAD SHX Text(4 in)
AutoCAD SHX Text(4 in)
AutoCAD SHX Text(6 in)
AutoCAD SHX Text102 mm
AutoCAD SHX Text153 mm
AutoCAD SHX Text153 mm
AutoCAD SHX Text102 mm
AutoCAD SHX TextFLASHING SLEEVE SHOWN IN EXPLODED VIEW
AutoCAD SHX TextPARAPET FLASHING (BY OTHERS)
AutoCAD SHX TextROOFING SYSTEM (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextALUMINUM REGLET (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2) (NOTE 2)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
-
CCP-2 0.0.14
Parapet Flashing
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX TextSLOPE
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)(NOTE 2)
AutoCAD SHX TextMETAL PARAPET FLASHING (BY OTHERS)
AutoCAD SHX TextTREATED NAILER AND PLASTER STOP. INSTALL PRIOR TO CEMENT PLASTER INSTALLATION (BY OTHERS)
AutoCAD SHX Text77MM (3 in) MIN.
AutoCAD SHX Text25MM (1 in) MIN.
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER EXTENDED OVER TOP OF PARAPET (BY OTHERS) (NOTE 1)
AutoCAD SHX TextROOFING MEMBRANE EXTENDED OVER TOP OF PARAPET
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextSEALANT (BY OTHERS)
-
CCP-2 0.0.15
Soffit with Continuous Vent
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX TextFRAMING (BY OTHERS)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF- FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextCORNER BEAD (BY OTHERS)
AutoCAD SHX TextCONTINUOUS SOFFIT VENT (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
-
CCP-2 0.0.16
Soffit/Fascia Intersection
™
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™NOTE:
1. FRAMING JOIST SPACED AT 609MM (24")REQUIRES 10MM (3/8") RIB LATHPERPENDICULAR TO JOISTS.
2. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
3. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 2)
AutoCAD SHX TextGALVANIZED SELF- FURRING LATH (BY OTHERS) (NOTE 2)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 3)(NOTE 3)
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
AutoCAD SHX Text10MM (3/8 In) RIB LATH FASTENED TO FRAMING SPACED MAXIMUM 609MM (24 in) O.C. (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 3)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
-
CCP-2 0.0.17
EPS Cornice
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. ADHESIVLY ATTACH EPS SHAPE TO CEMENT PLASTER BASE COAT WITH GENESIS OR GENESIS DM BASE COAT.2. BUILDING CODES REQUIRE 2 LAYERS OVER
WOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
3. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
™
AutoCAD SHX TextSLOPE
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 2)
AutoCAD SHX TextMETAL PARAPET FLASHING (BY OTHERS)
AutoCAD SHX Text77MM (3 in) MIN.
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCASING BEAD
AutoCAD SHX TextEPS FOAM SHAPE (NOTE 1)
AutoCAD SHX TextDRYVIT REINFORCING MESH EMBEDDED IN DRYVIT BASE COAT
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextCODE APPROVED WATER- RESISTIVE BARRIER (BY OTHERS) (NOTE 2)
AutoCAD SHX TextROOFING MEMBRANE LAPPED OVER TOP OF PARAPET TO OPPOSITE FACE (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 3)(NOTE 3)
-
CCP-2 0.0.18
Expansion Joint Intersection
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. LATH TO LAP OVER CONTROL JOINTFLANGES.
3. FRAMING BACKING IS REQUIRED AT ALLCONTROL JOINTS.
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER CONTINUOUS BEHIND CONTROL JOINTS (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextEMBED CONTROL JOINT IN SEALANT, AT ALL INTERSECTIONS
AutoCAD SHX TextFRAMING (BY OTHERS)
AutoCAD SHX TextCONTINUOUS VERTICAL CONTROL JOINTS (BY OTHERS)
AutoCAD SHX TextHORIZONTAL CONTROL JOINTS CUT AT ALL VERTICAL CONTROL JOINT INTERSECTIONS (BY OTHERS)
AutoCAD SHX TextCUT FLANGES OF CONTROL JOINT SO AS TO CREATE A TIGHT FIT WITH A UNIFORM DEPTH
AutoCAD SHX TextPROVIDE NEUTRAL CURE SILICONE BEDDING SEALANT AREA BEHIND CONTROL JOINT INTERSECTION
-
CCP-2 0.0.19
Horizontal or Vertical Expansion Joint
™
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
AutoCAD SHX TextEXPANSION JOINT (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2) (NOTE 2)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH, LAP OVER EXPANSION JOINT (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextFRAMING (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextFLASHING PAPER 203MM (8 in) ON EACH SIDE OF EXPANSION JOINT OVER CODE APPROVED WATER- RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
-
CCP-2 0.0.20
Termination at EIFS/Lap Siding
™
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2) (NOTE 2)
AutoCAD SHX TextFRAMING (BY OTHERS)
AutoCAD SHX TextEIFS
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextMETAL FLASHING (BY OTHERS)
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER BEHIND METAL FLASHING (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER LAPPED OVER FLASHING (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS)
AutoCAD SHX TextCASING BEAD WITH WEEPS (BY OTHERS)
AutoCAD SHX Text12MM (1/2 in) MIN. TYP.
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextMETAL FLASHING (BY OTHERS)
AutoCAD SHX TextLAP SIDING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER BEHIND METAL FLASHING EXTENDING 305MM (12 in) PAST CASING BEAD (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
-
CCP-2 0.0.21
Two-Piece Horizontal Expansion Joint
™
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED EXPANDED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2) (NOTE 2)
AutoCAD SHX TextFRAMING (BY OTHERS)
AutoCAD SHX TextSTRUCTURE (BY OTHERS)
AutoCAD SHX TextLEDGER ANGLE (BY OTHERS)
AutoCAD SHX TextEXPANSION JOINT WITH WEEPS (BY OTHERS)
AutoCAD SHX TextFLASHING PAPER 8" (203MM) ON EACH SIDE OF EXPANSION JOINT OVER WATER-RESISTIVE BARRIER (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextSEALANT AND BACKER ROD (BY OTHERS)
-
CCP-2 0.0.22
Pipe Railing Attachment
™
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
AutoCAD SHX TextTREATED WOOD BLOCKING (BY OTHERS)
AutoCAD SHX TextFLASHING PAPER: LAP OVER TOP AND BACK DOWN OVER WATER RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextMETAL PARAPET FLASHING (BY OTHERS)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)(NOTE 2)
AutoCAD SHX TextMETAL RAILING: SET IN SEALANT ALL AROUND (BY OTHERS)
AutoCAD SHX TextPRE DRILLED HOLES: SET IN SEALANT
AutoCAD SHX TextBLOCKING
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextSEALANT (BY OTHERS)
-
CCP-2 0.0.23
Hose Bib Penetration
™
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. PRE-DRILLED HOLES SET IN SEALANT.2. BUILDING CODES REQUIRE 2 LAYERS OVER
WOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
3. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
AutoCAD SHX TextFRAMING (BY OTHERS)
AutoCAD SHX TextSHEATHING (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 3)(NOTE 3)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 2)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 2)
AutoCAD SHX TextSEALANT (BY OTHERS) (NOTE 1)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
-
CCP-2 0.0.24
Sloped Sill
™
The architecture, engineering, and design of the project using the
Dryvit products is the responsibility of the project's design
professional. All systems must comply with local building codes and
standards. This detail is for general information and guidance only
and Dryvit specifically disclaims any liability for the use of this detail
and for the architecture, design, engineering or workmanship of any
project. The project design professional determines, in its sole
discretion, whether this detail or a functionally equivalent detail is
best suited for the project. Use of a functionally equivalent detail does
not violate Dryvit's warranty. This detail is subject to change without
notice. Contact Dryvit to ensure you have the most recent version.
Commercial Cement Plaster 2™
©
Dryvit Systems, Inc. 1969
Issued: 10/2016
NOTE:
1. BUILDING CODES REQUIRE 2 LAYERS OVERWOOD BASED SUBSTRATES. COMPLY WITHALL LOCAL CODE REQUIREMENTS.
2. OTHER APPROVED SCRATCH AND BROWNCOATS MAY BE ACCEPTABLE. CONSULTDRYVIT SYSTEMS, INC. FOR SPECIFICS.
AutoCAD SHX TextTREATED NAILER (BY OTHERS)
AutoCAD SHX TextBACKER ROD AND SEALANT (BY OTHERS)
AutoCAD SHX TextMETAL WINDOW SYSTEM (BY OTHERS)
AutoCAD SHX TextMETAL FLASHING WITH END DAMS (BY OTHERS)
AutoCAD SHX TextSEALANT (BY OTHERS)
AutoCAD SHX TextGALVANIZED SELF-FURRING LATH (BY OTHERS) (NOTE 1)
AutoCAD SHX TextOPENING WRAP LAPPED OVER WATER- RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX TextCODE APPROVED WATER-RESISTIVE BARRIER (BY OTHERS) (NOTE 1)
AutoCAD SHX Text6:12 MIN. SLOPE, MAX 305 (12 in) LENGTH
AutoCAD SHX TextCORNER BEAD, FILL SPACE SOLID WITH CEMENT PLASTER (BY OTHERS)
AutoCAD SHX TextDRYVIT FINISH OVER DRYVIT PRIMER
AutoCAD SHX TextCASING BEAD (BY OTHERS)
AutoCAD SHX TextDRYVIT COMMERCIAL CEMENT PLASTER BASE (NOTE 2)(NOTE 2)
Sheets and ViewsModel
CCP 2 01.pdfSheets and ViewsModel
CCP 2 02.pdfSheets and ViewsModel
CCP 2 03.pdfSheets and ViewsModel
CCP 2 04.pdfSheets and ViewsModel
CCP 2 05.pdfSheets and ViewsModel
CCP 2 06.pdfSheets and ViewsModel
CCP 2 07.pdfSheets and ViewsModel
CCP 2 07.pdfSheets and ViewsModel
CCP 2 08.pdfSheets and ViewsModel
CCP 2 09.pdfSheets and ViewsModel
CCP 2 10.pdfSheets and ViewsModel
CCP 2 11.pdfSheets and ViewsModel
CCP 2 12.pdfSheets and ViewsModel
CCP 2 13.pdfSheets and ViewsModel
CCP 2 14.pdfSheets and ViewsModel
CCP 2 15.pdfSheets and ViewsModel
CCP 2 16.pdfSheets and ViewsModel
CCP 2 17.pdfSheets and ViewsModel
CCP 2 18.pdfSheets and ViewsModel
CCP 2 19.pdfSheets and ViewsModel
CCP 2 20.pdfSheets and ViewsModel
CCP 2 21.pdfSheets and ViewsModel
CCP 2 22.pdfSheets and ViewsModel
CCP 2 23.pdfSheets and ViewsModel
CCP 2 24.pdfSheets and ViewsModel