Reference Title Scope
A-A-56032DCommercial ItemDescription Ink, Marking,Epoxy Base
This commercial item description coverscatalyzed epoxy system of marking inks formetallic or other non-porous surfaces andprinted wiring boards,
ANSI / ISEA 105American National Standardfor Hand ProtectionSelection Criteria
This method covers the selection criteria forhand protection systems including chemicalpermeation, puncture resistance, and abrasionresistance.
ANSI / SAEZ26.1 (Abrasion Resistance,
Plastics)
Safety Glazing Materials forGlazing Motor Vehicles andMotor Vehicle Equipment
The purpose of this test is to determine whetherthe plastic has a certain minimum resistance toabrasion
ANSI / SAEZ26.1 (Abrasion Resistance,
Safety Glass)
Safety Glazing Materials forGlazing Motor Vehicles andMotor Vehicle Equipment
The purpose of this test is to determine whethersafety glass has a certain minimum resistanceto abrasion.
ANSI INCITS 322 (5.10
Bar Code Abrasion)
Card Durability TestMethods
The purpose of this test is to determine theextent of 1D bar code abrasion resistance
ANSI INCITS 322 (5.11
Magnetic Stripe Abrasion)
Card Durability TestMethods
The purpose of this test is to determine theextent of magnetic stripe abrasion resistance
ANSI INCITS 322 (5.9
Surface Abrasion)
Card Durability TestMethods
The purpose of this test is to provide a generalmeans to produce controlled abrasion on acard surface
ANSI INCITS322 (Image Abrasion)
Card Durability TestMethods
The purpose of this test is to determine theextent of image abrasion resistance
AS 2001.2.28 Methods of Test for Textiles
This standard sets out a method for thedetermination of the abrasion resistance oftextile fabrics (applicable to all textile fabricsincluding coated and laminated fabrics, amethod for wet testing is also specified).
AS/NZS 1580.403.2Paints and Related Materials- Methods of Test
This Standard sets out a method fordetermining the abrasion resistance of a paintcoating or other finishes, such as anodizing,electroplating, paper products, rubbers,plastics, textiles, glass and concrete.
AS/NZS 4266.20Reconstituted Wood-BasedPanels - Methods of Test
This standard specifies a method fordetermining the resistance to surface abrasionof decorative surfaces by using the Taberabrader. It is applicable to all low pressureoverlaid particleboards and medium densityfibreboards (MDF's).
ASTM B607 (Appendix X2)
Standard Specification forAutocatalytic Nickel BoronCoatings for EngineeringUse
This test method will evaluate the resistance ofthe coating to abrasive wear.
ASTM B733 (Appendix X1)
Standard Specification forAutocatalytic (Electroless)Nickel-Phosphorus Coatingson Metal
This test method will evaluate the resistance ofthe coating to abrasive wear.
ASTM B893 (Annex A1)
Standard Specification forHard-Coat Anodizing ofMagnesium for EngineeringApplications
This specification covers requirements forelectrolytically formed oxide coatings onmagnesium and magnesium alloy parts whereappearance, abrasion resistance, andprotection against corrosion are important.
ASTM C957
Standard Specification forHigh-Solids Content, ColdLiquid-Applied ElastomericWaterproofing MembraneWith Integral WearingSurface
This specification describes the requiredproperties and test methods for a coldliquid-applied elastomeric membrane forwaterproofing building decks not subject tohydrostatic pressure. The specification appliesonly to a membrane system that has an integralwearing surface.
ASTM C1353
Standard Test Method Usingthe Taber Abraser forAbrasion Resistance ofDimension Stone Subjectedto Foot Traffic
This test methods covers the establishment ofan index of abrasion resistance bydetermination of loss of weight resulting fromabrasion of dimension stone.
ASTM C1405 (Section 7.6)
Standard Specification forGlazed Brick (Single firedBrick units)
This specification covers brick, having aceramic glaze finish fused to the body duringthe same process as the unit body firing, thatare intended for use in masonry and supplyingstructural or facing components, or both, to thestructure. This specification does not coverdouble-fired glazed brick. Some double-fireddecorative glazes have physical properties
which vary from those of single-fired glazes dueto the lower temperatures used in applying thedecorative coating.
ASTM C1803
Standard Guide for AbrasionResistance of MortarSurfaces Using a RotaryPlatform Abraser
This guide is intended to assist in establishingprocedures for determining the relativeresistance of treated or untreated mortarsurfaces.
ASTM C501
Standard Test Method forRelative Resistance to Wearof Unglazed Ceramic Tile bythe Taber Abraser
This test method covers the establishment ofan abrasive wear index by determination of theloss of weight resulting from abrasion ofunglazed ceramic tile.
ASTM C744
Standard Specification forPrefaced Concrete andCalcium Silicate MasonryUnits
This specification covers prefaced concretemasonry units with theexposed-to-view-in-place surfaces covered atthe point of manufacture with resin, resin andinert filler, or cement and inert filler to produce asmooth resinous tile facing. This specificationdoes not address, and therefore is notapplicable to, ground-face concrete masonryunits that are manufactured by grinding a thinlayer off the surface of a concrete masonry unitto expose aggregates within and polishing toproduce smooth, architectural finish.
ASTM D1044Standard Test Method forResistance of TransparentPlastics to Surface Abrasion
This test method describes a procedure forestimating the resistance of TransparentPlastics to Surface Abrasion
ASTM D154 (Section 18)Standard Guide for TestingVarnishes
This guide covers the selection and use ofprocedures for testing varnishes. Some testmethods are included, but most sections referto specific ASTM test methods
ASTM D2205 (Section 18)
Standard Guide forSelection of Tests for TrafficPaints
This guide covers the selection and use ofprocedures for testing traffic paints in thelaboratory and in the field.
ASTM D3389
Standard Test Method forCoated Fabrics AbrasionResistance (Rotary PlatformDouble-Head Abrader)
This test method covers the determination ofthe resistance to abrasion of fabrics coated withrubber or plastics
ASTM D3451 (Section 22)
Standard Practices forTesting Polymeric Powdersand Powder Coatings
These practices cover the selection and use ofprocedures for testing polymeric powders andpowder coatings.
ASTM D3489 (Section 13)
Standard Test Methods forMicrocellular UrethaneMaterials
ASTM D3730 (Section
10.1)
Standard Guide for TestingHigh-Performance InteriorArchitectural Wall Coatings
This guide covers the selection and use of testmethods for high-performance interiorarchitectural wall coatings (HIPAC) which differform more conventional coatings in that theyare tougher, more stain-resistance, moreabrasion-resistant and, ordinarily, designed tobe applied to wall surfaces of steel, masonry,and plaster or gypsum wallboard.
ASTM D3794 (Section
10.8.5.1)
Standard Guide for TestingCoil Coatings
This guide covers procedures for testing coilcoatings. The test methods included are listedin Table 1. Where more than one test method islisted for the same characteristic, no attempt ismade to indicate superiority of one method overanother.
ASTM D3884
Standard Guide for AbrasionResistance of TextileFabrics (Rotary Platform,Double-Head Method)
This guide covers the determination of theabrasion resistance of textile fabrics using therotary platform, double head tester (RPDH)
ASTM D4060
Standard Test Method forAbrasion Resistance ofOrganic Coatings by theTaber Abraser
This test method covers the determination ofthe resistance of organic coatings to abrasionproduced by the Taber Abraser on coatingsapplied to a plane, rigid surface, such as ametal panel.
ASTM D4685Standard Test Method forPile Retention of CorduroyFabrics
This test method covers the determination ofthe loss of pile, specifically pile pull out, due toabrasion.
ASTM D4712Standard Guide for TestingIndustrial Water-ReducibleCoatings
This guide covers the selection and use ofprocedures for testing water-reduciblecoatings, both pigmented and clear, utilizingsynthetic lattices, synthetic resin emulsions, orwater-reducible alkyds.
ASTM D5144 (Section
5.5.2)
Standard Guide for Use ofProtective CoatingStandards in Nuclear PowerPlants
This guide provides a common basis on whichprotective coatings for the surfaces of lightwater-moderated nuclear power generatingfacilities may be qualified and selected byreproducible evaluation tests.
ASTM D5146 (Section
10.1.1)
Standard Guide to TestingSolvent-Borne ArchitecturalCoatings
This guide covers the selection and use ofprocedures for testing solvent-borne coatingsto be used on exterior, interior or both types ofsurfaces.
ASTM D5324 (Section
10.1.1)
Standard Guide for TestingWater-Borne ArchitecturalCoatings
This guide covers the selection and use ofprocedures for testing water-borne coatings tobe used on exterior, interior or both types ofsurfaces.
ASTM D6037 (Method A)
Standard Test Methods forDry Abrasion MarResistance of High GlossCoatings
Two test methods are included. Test Method Auses a device that contains an abrasivewheel. Test Method B uses a device thatcontains a wheel that has been fitted withabrasive paper. Either method can be used toevaluate the dry abrasion mar resistance ofcoatings applied to planar, rigid surfaces.
ASTM D7255
Standard Test Method forAbrasion Resistance ofLeather Rotary Platform,Double Head Method)
This test method covers the determination ofthe abrasion resistance of leather using therotary platform, double-head tester (RPDH).
ASTM E1795
Standard Specification forNon-Reinforced LiquidCoating EncapsulationProducts for Leaded Paint inBuildings
This specification covers minimum materialperformance and laboratory test procedures fornon-reinforced liquid coating encapsulationproducts (single or multiple-coat systems) forleaded paint in buildings.
ASTM F1344 (Section 7.5)Standard Specification forRubber Floor Tile
This specification covers requirements for thecompound and physical characteristics ofrubber floor tile.
ASTM F1478
Standard Test Method forDetermination of AbrasionResistance of ImagesProduced from Copiers andPrinters (Taber Method)
This test method describes a procedure fordetermining the amount of image abraded fromthe surface of a document. This test methodmay be used to evaluate the abrasionresistance of images produced by business
imaging products, including nonimpact printers,thermal transfer printers, and copiers.
ASTM F1978
Standard Test Method forMeasuring AbrasionResistance of MetallicThermal Spray Coatings byUsing the Taber Abraser
This test method quantifies the abrasionresistance of metallic coatings produced bythermal spray processes on flat metallicsurfaces. It is intended as a means ofcharacterizing coatings used on surgicalimplants.
ASTM F2051 (Annex A1)
Standard Specification forImplantable Saline FilledBreast Prosthesis
This specification covers the requirements forsingle use saline inflatable, smooth andtextured silicone shell implantable breastprostheses, intended for use in surgicalreconstruction, augmentation, or replacementof the breast.
ASTM F2068 (Section
6.2.3)
Standard Specification forFemoral Prosthesis-MetallicImplants
This specification covers metallic stemmedfemoral prosthesis used to replace the naturalhip joint by means of hemi-arthroplasty or totalhip surgical procedures.
ASTM F362Standard Test Method forDetermining the Eraseabilityof Inked Ribbons
This test method covers the determination ofthe erasability of inked ribbons
ASTM F510
Standard Test Method forResistance to Abrasion ofResilient Floor CoveringsUsing an Abrader with a GritFeed Method
This test method covers the laboratoryprocedure for determining the abrasionresistance of resilient flooring using an abraderwith a grit feeder.
ASTM G195
Standard Guide forConducting Wear TestsUsing a Rotary PlatformAbraser
This guide covers and is intended to assist inestablishing procedures for conducting weartests of rigid or flexible materials utilizing therotary platform abraser.
Australia Departmentof Civil andEnvironmentalEngineering
Laboratory Tests forStrength, Hardness andAbrasiveness: ExplanatoryNotes.
Describes method of testing using TaberAbraser
Blu-Ray Disc (v1.2) Blu-ray Disc Read-OnlyFormat - Part 1: Basic
The entrance surface of the disc should havesufficient scratch resistance, which may be
Format Specifications improved by a protective coating.
Boeing P.S. 13208Hardcoating of AluminumAlloys
This Specification provides the requirementsand procedures for producing a hard oxidecoating on aluminum alloys. This coatingprovides excellent abrasion resistance forsliding wear applications, corrosion resistance,and electrical insulation. Corrosion resistancecan be increased by sealing the coating, butabrasion resistance is decreased.
BS 3900: Part E14
Paints and Varnishes;Determination of Resistanceto Abrasion {Part 1: RotatingAbrasive-Paper-CoveredWheel Method}
This part of ISO 7784 specifies a method fordetermining the resistance to abrasion of adried film of paint, varnish or related product,using abrasive paper attached to wheels andabrading by making a rotary movement
BS 3900: Part E15
Paints and Varnishes;Determination of Resistanceto Abrasion {Part 2: RotatingAbrasive Rubber WheelMethod}
This part of ISO 7784 specifies a method fordetermining the resistance to abrasion of adried film of paint, varnish or related product,using abrasive rubber wheels and abrading bymaking a rotary movement
BS 8204-3
Screed, bases and in situfloorings. Polymer modifiedcementitious levelingscreeds and wearingscreeds. Code of Practice
BS AU 178aSpecification for RoadVehicle Safety Glass
Specifies requirements for safety glass forinstallation as windscreens, other windows, oras partitions in motor vehicles and trailers.
BS EN 13672
Surfaces for sports areas -Determination of resistanceto abrasion of non-filledsynthetic turf
This document describes a method for thedetermination of the wear resistance of anon-filled synthetic turf surface using anabrasive wheel under laboratory conditions. Itis applicable to non-filled synthetic turf with apile height greater than 15mm.
BS EN 60903Live Working-Gloves ofInsulating Material
Mechanical testing requirements.
CFFA-1 &200 Standard Test Methods -Chemical Coated Fabrics
To determine the abrasion resistance ofchemical coated fabrics and films using a rotary
and Film platform double head tester.
CFFA-P-101C
Recommend MinimumPerformance Standards forVinyl Swimming PoolLiners-In-Ground
This document sets forth recommendedminimum performance standards for vinyl andother polymeric films, plain and printed, whichare used as in-ground swimming pool liners.
CID A-A-56032Military Specification - Ink,Marking, Epoxy Base
This specification covers a catalyzed epoxysystem of marking inks for metallic or othernon-porous surfaces.
CID A-A-59776 Gear, Fire Protective
This commercial item description covers therequirements for a structural fireman's coverallto be used by Navy damage control firefighters.
CNS K6591Method of Test forPolyurethane AthleticInstallation Material
This standard covers the test method forpolyurethane (PU) of athletic installation use.
CPA WR-01
Standard Test Method forthe Evaluation of WearResistance of LaminatedDecorative surfaces usingAbrading Wheels
This test measures the ability of alaminated decorative surface to resist abrasivewear-through of the decorative layer, utilizing aTaber rotary platform, double-head abraserequipped with abrading wheels.
CTS No. 5538Abrasion Resistance TaberAbraser
This procedure covers the determination of theresistance of coatings to abrasion using theTaber Abraser
DIN 52 347
Testing of Glass andPlastics; Abrasion Test;Method Using AbrasionWheels and Measurementsof Scattered Light
in German
DIN 53 109
Testing of Paper and Board;Determination of Abrasionby the Abrasion WheelMethod
in German
DIN 53 754Testing of Plastics;Determination of Resistanceof Wear by Abrasive Wheels
in German
DIN 53 799
Decorative LaminatedSheets on Basisof Aminoplastic Resins;Test Method
in German
DIN 68 861 T2Furniture Surfaces: Behaviorat Abrasion
in German
DLA1Determination of Resistanceto Surface Wear
This Appendix specifies a method of measuringthe ability of the surfaces of decorativelaminated sheets to maintain their originaldesign or colour under abrasive wear.
DPS 11.04 Hard Anodizing Aluminum
This process standard specifies proceduresand requirements for hard anodizing aluminumalloys. It shall be used when specified on theEngineering drawing.
EN 13310Kitchen Sinks - FunctionalRequirements and TestMethods
This standard specifies the functionalrequirements and test methods for domestickitchen sinks, used in residential (domestichouses, guest houses and similar) premises.This standard does not specify aesthetic anddimensional requirements. It does not apply toindustrial kitchen sinks. Note: All drawings areexamples only; other forms are permissible.
EN 13329-Annex E
Laminate floor coverings -Elements with a surfacelayer based on amnioplasticthermosetting resins -Specifications, requirementsand test methods
This annex specifies the method for measuringabrasion resistance and consequentlydetermining the abrasion class of laminate floorcovering elements. The test describedmeasures the ability of the surface layer toresist abrasive wear-through.
EN 13696
Wood flooring - Testmethods to determineelasticity and resistance towear and impact resistance
This document specifies two alternative testmethods to determine the resistance to wear oflacquered wood floorings and one method totest the elasticity of the lacquer.
EN 14323Wood-basedpanels-Melamine facedboards for interior uses-Test
This test measures the ability of the decorativesurface of melamine surfaces boards to resistabrasive wear-through by rotating a specimen
Methods in contact with cylindrical wheels covered withabrasive paper. The number of revolutions ofthe specimen required to cause a defineddegrees of abrasion is used as measures ofresistance to abrasion.
EN 14327
Leather - Physical andMechanical Tests -Determination of AbrasionResistance of AutomotiveLeather
This European Standard specifies a method ofdetermining abrasion resistance of automotiveleather
EN 14354-Annex DWood Based Panels - WoodVeneer Floor Covering
This method of test specifies a procedure todetermine the resistance to wear of lacqueredwood veneer floor covering.
EN 14431
Vitreous and PorcelainEnamels- Characteristics ofthe enamel coatings appliedto steel panels intended forarchitecture
EN 14688
Sanitary Appliances - WashBasins - FunctionalRequirements and TestMethods
This European Standard specifies thefunctional requirements and test methods forwash basins for domestic purposes.
EN 14864
Vitreous and PorcelainEnamels - Enamel coatingsapplied to steel for writingsurfaces- Specifications
EN 14904
Surfaces for Sports areas -Indoor surfaces formulti-sportsuse-Specification
This European Standard specifiesrequirements for surfaces for indoor facilitiesfor multi-sports use. It also covers surfacesystems which include both their supportingand upper layers whether prefabricated,produced in situ or a combination of the two.Not applicable to indoor tennis halls.
EN 438-2
Decorative High PressureLaminates (HPL);Sheets Based onThermosetting Resins; Part
The test measures the ability of the decorativesurface of the sheet under test to resistabrasive wear-through to the sub-layer.
2: Determination ofProperties
EN 655
Resilient FloorCoverings-Tiles ofagglomerated compositioncork with polyvinyl chloridewear layer-Specification
This European standard specifies thecharacteristics of agglomerated cork with awear layer based upon polyvinyl chloride andmodification thereof.
EN 660-2
Resilient floor coverings -Determination of wearresistance - Part 2:Frick-Taber Test
This European Standard describes theFrick-Taber method for determining the wearresistance of the wear layer of polyvinylchloride floor coverings under laboratoryconditions. The test method is applicable tofloor coverings with smooth surfaces. It can beused to determine the wear resistance ofsurfaces against abrasion and particularly forranking different wear layer types within onetype of product.
FDA Metallic PlasmaSprayed Coatings
Guidance for Industry on theTesting of Metallic PlasmaSprayed Coatings onOrthopedic Implants toSupport Reconsideration ofPostmarket SurveillanceRequirements
This guidance document represents theagency's current thinking on the testing resultsthat will enable FDA to reconsider therequirement for postmarket surveillance ofplasma sprayed hip prostheses.
Fed. SpecificationTT-P-0091D
Interim Federal Specification- Paint, Rubber Base,Styrene-Butadiene Type,Interior, for concrete floors.
This specification covers a rubber-base paintfor interior use on concrete floors.
Fed. Test Method Std.No. 191A Method5306.1
Abrasion Resistance ofCloth: Rotary Platform,Double-Head (Taber)Method
This method is intended for determining theabrasion resistance of cloths in terms ofpercent change in breaking strength, orbreaking strength after a given period ofabrasion, or the number of abrasion cyclesrequired to produce a specified state ofdestruction. It is used to evaluate clothdurability.
Fed. Test Method Std.No. GG-P-455b
Plates and Foils,Photographic
This specification covers the requirements forphotosensitive anodized aluminum sheets and
(Photosensitive AnodizedAluminum)
foils. For purposes of this specification, foils asreferred to in this specification is defined asmaterial 0.010 inch and thinner
IKEA Spec. No.IOS-TM-0002
Surface Resistance-TestMethods
Description of a method that measures theability of a coated surface to resist abrasivewear-through to the underlying substrate byassessing the resistance to liquid paraffin (fat)in the abraded area. The method is used oncoated wood, foiled and laminated substratesin applications where high surface resistance isrequired.
IPC-TM-650Abrasion (Taber Method)Solder Mask and ConformalCoating
This method is designed to evaluate theresistance of solder mask or conformallysurfaces to rubbing abrasion.
ISO 10074Specifications for HardAnodic Oxidation Coatingson Aluminum and its Alloys
This International Standard specifiesrequirements for hard anodic oxidation coatingson aluminum and its alloys, including testmethods.
ISO 15082Road Vehicles-Tests forrigid plastic safety glazingmaterials
Determination of whether the plastic, safetyglazing material has a certain minimumresistance to abrasion at ambient temperatureunder dry or wet (car wash) conditions.
ISO 2046-Annex CEffects of Surface Finish andColour on ScratchResistance
The test measures the ability of a decorativesurface of the sheet under test to resistabrasive wear through to the sub-layer.
ISO 24338Laminate Floor Coverings -Determination of AbrasionResistance
This International Standard specifies themethod for measuring abrasion of laminatefloor covering elements.
ISO 3537Road Vehicles - SafetyGlazing Materials -Mechanical Tests
This International Standard specifiesmechanical test methods relating to the safetyrequirements for all safety glazing materials ina road vehicle, whatever the type of glass orother material of which they are composed.
ISO 5470-1Rubber or Plastics CoatedFabrics - Determination ofAbrasion Resistance
This part of ISO 5470 describes a method ofassessing the abrasive wear resistance ofcoated fabrics.
ISO 7784-1Paints and Varnishes;Determination of Resistanceto Abrasion
This part of ISO 7784 specifies a method fordetermining the resistance to abrasion of adried film of paint, varnish or related product,using abrasive paper attached to wheels andabrading by making a rotary movement
ISO 7784-2Paints and Varnishes;Determination of Resistanceto Abrasion
This part of ISO 7784 specifies a method fordetermining the resistance to abrasion of adried film of paint, varnish or related product,using abrasive rubber wheels and abrading bymaking a rotary movement
ISO 9352Plastics; Determination ofResistance to Wear byAbrasive Wheels
This International Standard specifies a generalmethod for determining the resistance toabrasive wear of plastics under the action ofabrasive wheels. It is equally applicable tomoulded test specimens, components andfinished products.
JC Penney - MTC-205
Abrasion Resistance ofTextile Fabrics (Rotary-Platform, Double-HeadMethod)
To determine the abrasion resistance of textilefabrics using the rotary-platform double-headtester.
JC Penney - PPS#303-03076
JCPenny Product Research& Technology LaboratoriesProduct PerformanceStandard PPS# 303-0307Luggage
Flat Abrasion, CS-17 wheels, 100g load, 5400cycles
JIS A 1453
Method of Abrasion Test forBuilding Materials and Partof Building Construction(Abrasive-Paper Method)
This Japanese Industrial Standard applies tobuilding materials and parts of buildingconstruction and specifies the testing methodto evaluate the degree of abrasion of the testpiece.
JIS H 8503Methods of WearResistance for MetallicCoatings
This is a test to examine the wear resistance ofmetallic coatings.
JIS K 5600: Part 5,Section 8
Testing Methods for Paints{Part 5: Mechanical propertyof film -- Section 8: Abrasionresistance (Rotating
This Standard is one of a series of standardsdealing with the sampling and testing of paints,varnishes and related products. This Standardspecifies a method for determining the
abrasive paper coveredwheel method)}
resistance to abrasion of a dried film of paint,varnish or related product, using abrasiverubber wheels and abrading by making a rotarymovement.
JIS K 5600: Part 5,Section 9
Testing Methods for Paints{Part 5: Mechanical propertyof film -- Section 9: Abrasionresistance (Rotatingabrasive rubber wheelmethod)}
This Standard is one of a series of standardsdealing with the sampling and testing of paints,varnishes and related products. This Standardspecifies a method for determining theresistance to abrasion of a dried film of paint,varnish or related product, using abrasiverubber wheels and abrading by making a rotarymovement.
JIS K 6735Plastic-polycarbonatesheet-type, size andcharacteristics
JIS K 6902Testing Method forLaminated ThermosettingDecorative Sheets
This Japanese Industrial Standard specifies thetesting method for laminated thermosettingdecorative sheets.
JIS K 7204Testing Method for AbrasionResistance of Plastics byAbrasive Wheels
This Japanese Industrial Standard specifies thetesting method for the abrasion resistance ofplastics by abrading the test piece, particularlyin, with an abrasive wheel.
JIS K6264
Rubber, Vulcanized orThermoplastic -Determination of AbrasionResistance - Part2: TestingMethods
This method specifies the testing methods fordetermination of abrasion resistance of rubber,vulcanized or thermoplastic (hereafter referredto as "vulcanized rubber").
JIS L 1018Test Methods for knittedfabrics
JIS L 1021Textile Floor Covering - Part11: Determination of Wear
This Japanese Industrial Standard specifies thetesting methods for determination of wool fiberintegrity using an abrasion machine.
JIS L 1085Test Methods forNon-Woven InterliningFabrics
JIS L 1096 Testing for Woven Fabrics
This Japanese Industrial Standard specifies thetesting methods for the evaluation of generalcharacteristics of woven fabric foundationcloth.
JNB 30.04.09Abrasion Resistance ofPrinted Graphics
This test procedure is used to determine theabrasion resistance of decorativefinishes/graphics, used within the vehicleinterior. The test shall be used to give anindication of the comparative wearcharacteristics of painted, printed or hotembossed finishes, to plastic substrates. Thetest is used to determine the desired wearcharacteristics are met.
LAT-4-2200 Hard AnodizingThis method covers the requirements foranodization of aluminum and it alloys
MIL-A-8625F(1)
Military Specification -Anodic Coatings forAluminum and AluminumAlloys
This specification covers the requirements forsix types and two classes of electrolyticallyformed anodic coatings on aluminum andaluminum alloys for non-architecturalapplications.
MIL-C-83409
Military Specification -Coatings, Visor,Polycarbonate, FlyingHelmet
This specification covers the optical anddurability requirements fro abrasion resistingcoatings as applied polycarbonate visorsconforming to MIL-V-43511.
MIL-DTL-15024FMilitary Specification -Plates, Tags, and Bands forIdentification of Equipment
This specification covers the materials andphysical characteristics of plates, tags andbands (identification devices) used foridentification of equipment.
MIL-DTL-19834C
Plates, Identification orInstruction, Metal Foil,Adhesive Backed - GeneralSpecification For
This specification covers adhesive-backedmetal foil identification or instruction plates,herein referred to as identification plates, foruse as internal and external equipmentidentification or instruction (see 6.1).
MIL-DTL-22992F
General Specification forConnectors, Plugs andReceptacles, ElectricalWaterproof, Quick
This specification covers multicontact heavyduty, quick disconnect, waterproof, electricalplug and receptacle connectors and associatedaccessories for electronic and electrical power
Disconnect, Heavy DutyType
and control circuits.
MIL-DTL-43511DDetail Specification - Visors,Flying Helmet,Polycarbonate
This specification covers general andperformance requirements for curvedpolycarbonate flyer's helmet visors worn byaircrew personnel.
MIL-DTL-43511DDetail Specification - Visors,Flying Helmet,Polycarbonate
This specification covers general andperformance requirements for curvedpolycarbonate flyer's helmet visors worn byaircrew personnel.
MIL-P-18493
Military Specification -Packing, Performed,Carbon; and Carbon Stock,Packing
This specification covers carbon packingmaterial (1700) for rotary rod and shaft.
MIL-PRF-24613APerformance Specification -Deck Covering Materials,Interior, Cosmetic Polymer
This specification establishes the performancerequirements for cosmetic deck coveringmaterials to be applied either directly overprimed or unprimed, clean steel and aluminuminterior deck surfaces, or over deck coveringunderlay materials conforming toMIL-PRF-3135, that provide a wear resistant,low maintenance deck surface.
MIL-PRF-24712AMilitary Specification- Coatings, Powder (Metric)
This specification covers powder coatings forinterior steel, aluminum, copper-nickle andbronze equipment, furniture, and electrical boxsurfaces and on exterior steel, aluminum,copper-nickel, and bronze surfaces exposed tomarine atmosphere, high humidity, seawaterand weathering.
MIL-PRF-28800F
Military Specification -General Specification forTest Equipment for use withElectrical and ElectronicEquipment
This specification describes the generalrequirements for test equipment used in testingelectrical and electronic equipment.
MIL-PRF-32170APerformance Specification -Deck Tiles, Wear Resistant
This specification establishes the requirementsfor wear-resistant and fatigue reducing deck tilesystems (including required adhesives and/or
sealers) that are halogen free and require nofloor finish used in Naval shipboard interiorapplications.
MIL-PRF-32171BPerformance Specification -Deck Coatings, HighDurability
This specification establishes the requirementsfor high-durability, wear-resistant deck coatingsfor use in high-traffic areas, with minimalmaintenance.
MIL-STD-13231CDepartment of DefenseStandard Practice - Markingof Electronic Items
This standard covers the general requirementsfor marking of electronic items.
MIL-T-53029C
Military Specification -Tanks, Fabric, Collapsible:10,000; 20,000; And 50,000Gallon, Drinking Water
This specification covers tanks, fabric,collapsible: 10,000; 20,000; and 50,000 gallonfor drinking water storage, complete withfittings and repair items.
MIL-V-43511CMilitary Specification -Visors, Flyer's Helmet,Polycarbonate
The abrasion resistance coating test shall beconducted in accordance with MIL-C-83409
NALFA LF-01 Laminate FlooringThis test measures the ability of the surface oflaminate flooring to resist abrasive wearthrough the décor layer.
NASTAManufacturing Standardsand Specifications forTextbooks
If offset printed on coated cover material, aprotective top coating for abrasion resistance isrequired.
National AircraftStandard NAS 1192
Performance Specificationfor Hard Anodic Coatings onAluminum Alloys
This specification defines the performancerequirements for hard anodic coatings onaluminum and aluminum alloy parts
NEMA LD3High Pressure DecorativeLaminates
This test measures the ability of the surface ofhigh-pressure decorative laminate to resistabrasive wear-through of the decorative layer.
NF G 37-121
Rubber or Plastic CoatedFabric-Determination of theWear Resistance byRubbing with two AbrasiveWheels
(in French)
NF T30-015Abrasion Resistance Test onPaint
(in French)
NHDOT Section 711Preformed RetroreflectivePavement Marking Tape
Tape shall consist of glass spheres of a highoptical quality imbedded into a binder on asuitable backing that is pre-coated with apressure-sensitive adhesive.
NHTSA 49 CFR571.205
Glazing MaterialsThis standard specifies requirements forglazing materials for use in motor vehicles andmotor vehicle equipment.
NIOSHCET-APRS-STP-0316
Standard Test Procedure forDetermination of Haze,Luminous Transmittance,and Abrasion Properties ofPrimary Lens SystemMaterials for Full FacepieceRespiratory ProtectiveDevices (RPS)
The purpose of this test is to quantify the haze,luminous transmittance, and abrasionresistance properties of the primary lensmaterial of a full facepiece RPD
Nokia DMXS1146-ENMenu Paint ApprovalTesting Requirements
This document details the NMP best practicefor the acceptance and verification of coatingsand paint finishes applied to Nokia plastics forthe Menu system.
NSF/ANSI 35High Pressure DecorativeLaminates for SurfacingFood Service Equipment
This Standard applies to high pressuredecorative laminates for use as work andnonwork surfaces of food service equipment onwhich direct food contact during normalpreparation or holding operations is notintended, expected, or reasonable.Applications of high pressure decorativelaminates covered by this Standard includewait stations, service counters, and othercounters when used in conjunction with cuttingboards or other means of preventing direct foodcontact with the laminate. High pressuredecorative laminates used on equipment forwhich other NSF or ANSI/NSF Standards orCriteria exist shall also comply with theapplicable requirements therein.
NSF/ANSI 49 Class II (Laminar Flow) This Standard applies to Class II (laminar flow)
Biohazard Cabinetry biosafety cabinetry designed to minimizehazards inherent in work with agents assignedto biosafety levels 1, 2, 3, or 4 and defines thetests that shall be passed by such cabinetry tomeet this Standard.
NSF/ANSI 51 Food Equipment Materials
This Standard is applicable to the materials andfinishes used in the manufacture of foodequipment (e.g., broiler, beverage dispenser,cutting board, stock pot).
SAE AS 38386Duct Assembly, Gound,Conditioned Air, Insulated,Flexible
This document covers insulated, flexible airduct assemblies for portable ground support airconditioners and heaters. (Section 4.6.14 -Abrasion reistance test)
SAE AMS 2438Chromium Coating: Thin,Hard, Dense Deposit
This specification covers the engineeringrequirements for the deposition of a thin, harddense chromium coating on surfaces of ferrousand non ferrous alloys and the properties of thecoating.
SAE AMS 2469G
Hard Anodic CoatingTreatment of Aluminum andAluminum Alloys Processingand PerformanceRequirements
This specification establishes the engineeringrequirements for producing a hard anodiccoating on aluminum and aluminum alloys andthe properties of such coating.
SAE J 1530
Test Method for DeterminingResistance to Fiber Loss,Resistance to Abrasion andBearding of AutomotiveCarpet Materials
This test method covers determination ofabrasion resistance, fiber loss and beardingresistance of automotive carpet materials.
SAE J 1847Abrasion Resistance Testing- Vehicle Exterior Graphicsand Pin Striping
This SAE Recommended practice applies tothe abrasion resistance testing of decorativetapes, graphics, and pin striping. It may alsohave relevance to certain vehicle labels andplastic wood grain film. The resistance toabrasive damage is judged qualitatively by itseffect on the legibility, pattern, and color of thegraphic marking.
SAE J 2394Seven-Conductor Cable forAbs Power
This SAE Standard establishes the minimumconstruction and performance requirements forseven-conductor 1/8-2/10-4/12 cable for use on
trucks and trailers.
SAE J 3097
Standard for Safety GlazingMotor Vehicles and MotorVehicle EquipmentOperating on LandHighways - Safety Standard
Specifications, test methods, and usageprovisions for safety materials used for glazingof motor vehicles and motor vehicle equipmentoperating on land highways. (See tests 12 and13)
SAE J 315Surface VehicleStandard-Fiberboard TestProcedure
This SAE provides test methods fordetermining the critical characteristics of basicor finished fiberboard products. Whereapplicable, methods of tests developed by SAEand ASTM have been referenced.
SAE J 365Method of TestingResistance to Scuffing ofTrim Materials
This test can be used to determine theresistance to scuffing of test specimens suchas fiberboards, fabrics, vinyl coated fabrics,leathers, and similar trim materials.
SAE J 80 Automotive Rubber Mats
This SAE recommended practice covers therequirements for rubber floor mats made fromfive types of rubber compound as required bythe physical property requirements of theapplication.
SAE J 948
Test Method for DeterminingResistance to Abrasion ofAutomotive Bodycloth, Vinyl,and Leather, and theSnagging of AutomotiveBodycloth
The Taber method of test is applicable fordetermining the resistance to snagging andabrasion of automotive fabrics and/orvinyl-coated fabrics.
SIS 92 35 09Floor Materials -Determination of AbrasionResistance
This standard describes a method for thedetermination of the abrasion resistance oforganic flooring materials when exposed towalking traffic of a revolving nature (pointabrasion). The method is not however suitedto asphalt, textile carpeting, or unlacqueredwood.
Tappi T 476Abrasion Loss of Paper andPaperboard (Taber-typemethod)
The objective of this method is to determine theresistance of surfaces of paper and paperboardto the action of abrasion, either wet or dry, bymeasuring abrasion loss. This test is notapplicable to the surfaces treated with wax orsimilar materials which would fill in the pores of
the abrasive wheels.
UN EN 48-250Paint andVarnishes-Resistance toAbrasion-Taber Method
This norm specifies a method for thedetermination of resistance to abrasion forpaints, varnishes and products when using theTaber Abraser.
UNE 56842
(translated) This norm applies to the furniture ofkitchen or kitchen furniture elements just assupply themselves for their final use, not beingvalid to evaluate the characteristics of thecoverings (laminated plastics or other) ofindependent form.
UNE 57095Paper and cardboard -Determination of Resistanceto Abrasion - Taber Method
(translated) This norm intends to describe tothe method of measurement of the sensitivity ofthe faces of paper or cardboard to the action ofstandardized surfaces abrasives, as much inhumid as in dry, using the Taber apparatus.
UNI 9115Furniture - Test for surfacefinishes - Behaviour ofsurfaces to wear abrasion.
(translated) It establishes a method in order toestimate the surface of furniture and is used tomaintain the design, color or aspect andsubject them to abrasive action. The method isadapted in order to compare various finish, oras a control test in order to assure that adetermined level of furniture surfaceperformance is maintained and applied to all.
United Nations - ECERegulation 43
Uniform ProvisionsConcerning the Approval ofSafety Glazing Materials andtheir installation on Vehicles
This Regulation applies to safety glazing andglazing materials intended for installation aswindscreens or other panes, or as partitioning,on power-driven vehicles and their trailers.
USIFI-DOC-001Test MethodRecommendations Coatedand Laminated Fabrics
This document provides recommendations fortest methods to be used in evaluating andcharacterizing coated and laminated fabrics foruse in military applications.
USIFI-DTL-53308
Detail Specification Clothand Strip, Laminated orCoated, Vinyl, Reinforced,High Strength, Flexible
This specification covers three types, fourclasses, and two forms of laminated or coatedcloth.
USIFI-PRF-44423Performance SpecificationCloth, Flame Resistant,Light weight, Reversible
This specification covers a flame resistant, lightweight, reversible cloth.
WSP 020.4.R3(12)
Standard Test Method forAbrasion Resistance ofNonwoven Materials (RotaryPlatform, Double-HeadMethod)
This method covers the determination of theabrasion resistance of nonwoven fabrics usingthe rotary platform, double-head tester (RPHD).