Conditions and loopsDay 4
Computer Programming through Robotics
CPST 410
Summer 2009
7/1/09 Harry Howard, CPST 410, Tulane University 2
Course organization
Course home page (http://robolab.tulane.edu/CPST410/)
Lab (Newcomb 442) will be open for practice with 3-4 Macs, but you can bring your own laptop and all robots.
Sound in NXT-G
Kelly §6 Make some noise!
7/1/09 Harry Howard, CPST 410, Tulane University 4
The SOUND block
1. This icon shows whether the block will play a sound file or a tone.
2. This icon shows whether the block will start or stop playing a sound.
3. This icon shows the block’s volume. An icon with four orange bars is set to the loudest volume.
4. You can drag data wires from other blocks to this block’s data hub that will affect the Sound block’s properties.
7/1/09 Harry Howard, CPST 410, Tulane University 5
Kelly's example, reversed
Spot, move forward 1 rotations at 50% power coasting to a stop and then play me a C note for 2 seconds at 75% volume.
7/1/09 Harry Howard, CPST 410, Tulane University 6
MoveSound.rbt
Sound in NXC
7/1/09 Harry Howard, CPST 410, Tulane University 8
Two useful sound functions
DefinitionsPlayTone(frequency, duration)PlayFile(filename)
ExamplesPlayTone(440, 500); Wait(500);PlayFile(“Startup.rso”);
Note that PlayTone executes immediately, so that all by itself, it does not play for 500 ms; it relies on Wait to actually extend the duration to the one specified.
7/1/09 Harry Howard, CPST 410, Tulane University 9
Do Kelly's example in NXC
TRIBOT, move forward 1 rotation at 50% power coasting to a stop and then play me a C note for 2 seconds at 75% volume.
7/1/09 Harry Howard, CPST 410, Tulane University 10
MoveSound.nxc
task main()
{
RotateMotor(OUT_AC, 75, 360);
PlayTone(1047,2000);
Wait(2000);
}
Waiting
Kelly §10 Wait for it!
7/1/09 Harry Howard, CPST 410, Tulane University 12
Waiting
The robot is almost always waiting to do something, even when it is already doing something: TRIBOT is moving towards a black line, waiting for the Light
sensor to detect it. TRIBOT is preparing to throw a ball at a target, waiting for the
Touch sensor to be pressed and released. TRIBOT is rolling towards the wall, waiting for the Ultrasonic
sensor to detect it. TRIBOT is sitting at the start line, waiting for the Sound sensor to
hear me yell “Go!”.
7/1/09 Harry Howard, CPST 410, Tulane University 13
Conditions
The WAIT block will stop waiting when specific conditions are met.
The conditions are usually given by some kind of sensor feedback.
The blocks for each condition can be found in two ways:Common palette > Wait.By changing the setting from Time to Sensor on the
Time WAIT block.
7/1/09 Harry Howard, CPST 410, Tulane University 14
The conditions
Time waitTouch sensor waitLight sensor waitUltrasonic sensor waitNXT Buttons waitRotation sensor waitReceive Message wait
7/1/09 Harry Howard, CPST 410, Tulane University 15
A simple test of a condition
TRIBOT, move forward for an unlimited duration at a power of 50 until the Touch sensor is pressed.
7/1/09 Harry Howard, CPST 410, Tulane University 16
MoveTilTouch.rbt
7/1/09 Harry Howard, CPST 410, Tulane University 17
A more complex example
SPOT, move forward for 1 rotation at 50% power, brake, and beep. If your Light sensor detects a light level greater than 30, move backward 1/2 rotation at 50% power, coasting to a stop.
7/1/09 Harry Howard, CPST 410, Tulane University 18
MoveTilLight.rbt
Conditions in NXC
7/1/09 Harry Howard, CPST 410, Tulane University 20
A complication
The sensor functions in NXC do not include this ability to wait; all they do is read sensor values.
So you have to add the condition that the sensor value is supposed to meet, yourself.
7/1/09 Harry Howard, CPST 410, Tulane University 21
If
There are two optionsif (condition) consequence
if (condition) consequence else alternative
Examplesif (x == 1) y = 2;
if (x == 1) { y = 2; z = 3; }
if (x == 1) y = 3; else y = 4;
7/1/09 Harry Howard, CPST 410, Tulane University 22
We can’t do the simple test
TRIBOT, move forward for an unlimited duration at a power of 50 until the Touch sensor is pressed.
PROBLEM: there is no ‘unlimited’ parameter for any of the NXC movement functions, so we skip this task, though the next slide shows what we would want the program to look like.
7/1/09 Harry Howard, CPST 410, Tulane University 23
MoveTilTouch.nxc
task main()
{
OnFwd(OUT_AC, 50);
if (Sensor(S1) == 1)
{
Off(OUT_AC);
}
}
7/1/09 Harry Howard, CPST 410, Tulane University 24
The more complex example
TRIBOT, move forward for 1 rotation at 50% power, brake, and beep. If your Light sensor detects a light level greater than 30, move backward 1/2 rotation at 50% power, coasting to a stop.
7/1/09 Harry Howard, CPST 410, Tulane University 25
MoveTilLight.rbt
task main(){RotateMotor(OUT_BC, 50, 360);PlayTone(1047, 500);Wait(500);if (Sensor(S3) > 30)
{ RotateMotor(OUT_BC, 50, -180);}
}
Loops
Kelly §11 Round and Round
7/1/09 Harry Howard, CPST 410, Tulane University 27
How would you do this?
TRIBOT, display the output of the Light sensor briefly (500ms) 10 times.
7/1/09 Harry Howard, CPST 410, Tulane University 28
The LOOP block
The LOOP block repeats what is inside it until a condition is met.The loop break conditions are the same as the
WAIT conditions.
You drop a block inside a loop by grabbing the block, holding down the mouse button, and dropping it inside when the loop expands.
7/1/09 Harry Howard, CPST 410, Tulane University 29
Go ahead and do it
TRIBOT, display the output of the Light sensor briefly (1s) 10 times.
7/1/09 Harry Howard, CPST 410, Tulane University 30
DisplaySensorLoop.rbt
Loops in NXC
7/1/09 Harry Howard, CPST 410, Tulane University 32
REPEAT
The repeat command, repeat(t) {}, repeats what is in the curly brackets for the number of times given by t.
7/1/09 Harry Howard, CPST 410, Tulane University 33
Convert the example to NXC
TRIBOT, display the raw output of the Light sensor briefly (1s) 10 times.
7/1/09 Harry Howard, CPST 410, Tulane University 34
DisplaySensorLoop.nxcint light;
string text_light;
task main()
{
repeat(10)
{
light = Sensor(S3);
txt_light = NumToStr(light);
TextOut(0, LCD_LINE4, txt_light);
Wait(1000);
}
}
More practiceProgram each bit of pseudocode in NXT-G
and then in NXC.
My suggestion follows each bit of pseudocode, so don’t look ahead until you
are finished with your program!
7/1/09 Harry Howard, CPST 410, Tulane University 36
Follow up
TRIBOT, display the output of the Light sensor briefly (1s) 10 times and beep after each display. Laugh when you are finished.
7/1/09 Harry Howard, CPST 410, Tulane University 37
SensorLoopSound.rbt
7/1/09 Harry Howard, CPST 410, Tulane University 38
SensorLoopSound.nxcint light;string text_light;task main(){
repeat(10){
light = Sensor(S3);txt_light = NumToStr(light);TextOut(0, LCD_LINE4, txt_light);Wait(1000);PlayTone(1047,500);Wait(500);
}PlayFile(“Laughing 02.rso”);Wait(1000);
}
7/1/09 Harry Howard, CPST 410, Tulane University 39
Epilog on scope
Note the difference being in the loop versus being out of the loop makes. PlayTone is played 10 times, because it is in the loop. PlayFile is only played once, because it is not in the loop.
The effect of an expression like repeat is known as its scope, and in NXC the scope of an expression is stated explicitly by means of the curly brackets.
7/1/09 Harry Howard, CPST 410, Tulane University 40
Thought experiment
How would you make TRIBOT move forward and then turn right -- four times?By dropping in 8 MOVE blocks, each with the
same settings (one for each forward move, and one for each turn).
Does this sound like a good usage of your time?No!
7/1/09 Harry Howard, CPST 410, Tulane University 41
The pseudocode
TRIBOT, move forward for 0.5 s at 50% power and then make a 90° turn for 0.65 s also at 50% power. Do this 4 times.
7/1/09 Harry Howard, CPST 410, Tulane University 42
RepeatTurn.rbt
7/1/09 Harry Howard, CPST 410, Tulane University 43
Turning in NXC
You may have noticed that the NXC movement functions do not have the nice ‘steering wheel’ ability that NXT-G has.
The trick to turning in NXC is to reverse a motor. I’ll leave it up to you to figure out which one.
7/1/09 Harry Howard, CPST 410, Tulane University 44
RepeatTurn.nxc
task main()
{
repeat(4)
{
OnFwd(OUT_BC, 50);
Wait(500);
OnRev(OUT_C, 50);
Wait(650);
}
}
7/1/09 Harry Howard, CPST 410, Tulane University 45
Mix them up
TRIBOT, move forward for 1 rotation at 50% power and coast. If your Light sensor detects a level greater than 20, beep and move backward 1/2 rotation at 50% power, coasting to a stop. Do this 3 times, then say the number ‘three’.
7/1/09 Harry Howard, CPST 410, Tulane University 46
MoveLightLoop.rbt
7/1/09 Harry Howard, CPST 410, Tulane University 47
MoveLightLoop.nxctask main(){
repeat(3){
RotateMotor(OUT_BC, 50, 360);if (Sensor(S3) > 20) {
PlayTone(1047,500);Wait(500);RotateMotor(OUT_BC, 50, -180);
}}PlayFile(“03.rso”);Wait(1000);
}
7/1/09 Harry Howard, CPST 410, Tulane University 48
Next time
Quiz 1This will just be a quiz on the blocks.
More loops, switching.Random numbers.'Line Follower' - project done in class