Doc No: 41022 rev. 01 - Declaration of Conformity CoolX Series 60601-1 Prepared: S. I. Cionca Date: 11th August 2017
DECLARATION OF CONFORMITY
Product Name : CoolX Series Product Type : Component Power Supply Model Number : CXabc-wxyz-defgh
where: CX = all CoolX part numbers start with ‘CX’ ab = 06 06 = 600W output c = M M = Medical product w, x, y, z = 0, #, A, B, C, D, E or G
0 = Unpopulated slot; # = Unavailable slot (due to the presence of a multi-slot module in a neighboring slot); A = CmA; B = CmB; C = CmC; D = CmD; E = CmE; G = CmG
d = N; C; S; P or X N = Standard model (Unconfigured) C = Conformal Coating S = Ruggedised + Conformal Coating P = Configured
X = Internal use only e = ‘-‘; 0 – 9 or A-Z
‘-‘ = Screw Terminal (Standard) 1 = IEC Terminal
4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage A–Z = Other connector options (cables etc) f = A or B A = 12V Aux output (standard) B = 5V Aux output g = Not used; ‘-‘ or L Not used = Standard model (if h is not used)
‘-‘ = Standard model (if h is used) L = Cover h = Optional. Any alphanumeric character. Logistic use only.
Excelsys Technologies Ltd. 27 Eastgate Drive Eastgate Business Park Little Island Co. Cork, Ireland Tel: + 353 21 4354716 Fax: + 353 21 4354864
Doc No: 41022 rev. 01 - Declaration of Conformity CoolX Series 60601-1 Prepared: S. I. Cionca Date: 11th August 2017
Excelsys Technologies Ltd. confirms that this product conforms to: Safety Safety of Medical Electrical Equipment: EN 60601-1: 2006 / A1: 2013 / AC: 2014 / A12: 2014 Supplementary Information Safety tests were conducted by TÜV Rheinland LGA Products GmbH. By conformance with the standards referenced, the product follows the provisions of EC Directive 2014/35/EU (Low Voltage Directive) with the exception of the enclosure requirement. These products are only for inclusion by professional installers within other equipment and must not be operated as stand alone products. These power supplies provide REINFORCED INSULATION between input and output and may be used as an SELV circuit or a TNV power source which is insulated from the AC mains. The maximum ambient temperature must not exceed 40ºC at full load. Place of Issue: Cork, Ireland For and on behalf of Date of Issue: 11th August 2017 Excelsys Technologies Limited
Dermot Flynn
Doc No: 41023 rev. 00 - Declaration of Conformity CoolX Series 60601-1-2 Prepared: S. I. Cionca Date: 17
th October 2016
DECLARATION OF CONFORMITY
Product Name: CoolX Series Product Type: Component Power Supply Model Number: CXabc-wxyz-defgh
Where: CX = all CoolX part numbers start with ‘CX’ ab = 06 06 = 600W output c = M M = Medical product w, x, y, z = A, B, C or D A = CmA B = CmB C = CmC D = CmD d = N; C; S; P or X N = Standard model (Unconfigured) C = Conformal Coating S = Ruggedised incl. Conformal Coating P = Configured
X = Internal use only e = ‘-‘; 0 – 9 or A-Z
‘-‘ = Screw Terminal (Standard) 1 = IEC Terminal
4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage A–Z = Other connector options (cables etc) f = A or B A = 12V Aux output (standard) B = 5V Aux output g = ‘-‘; A-Z ‘-‘ = Default (standard) A-Z = Reserved for internal use (software variants) h = Optional. Any alphanumeric character. Logistic use only.
See Page 2.
Excelsys Technologies Ltd. 27 Eastgate Drive Eastgate Business Park Little Island Co. Cork, Ireland Tel: + 353 21 4354716 Fax: + 353 21 4354864
Doc No: 41023 rev. 00 - Declaration of Conformity CoolX Series 60601-1-2 Prepared: S. I. Cionca Date: 17
th October 2016
Excelsys Technologies Ltd. confirms that this product conforms to: IEC 60601-1-2: 2014 (4
th Edition)
Medical electrical equipment – Part 1-2: General requirements for basic safety and essential performance – Collateral Standard: Electromagnetic disturbances – Requirements and tests Testing was conducted by Compliance Engineering Ireland Ltd. Place of Issue: Cork, Ireland For and on behalf of Date of Issue: 17
th October 2016 Excelsys Technologies Limited
Dermot Flynn
Doc No: 41024 rev. 01 - Declaration of Conformity CoolX Series 60950-1 & 62368-1 Prepared: S. I. Cionca Date: 11th August 2017
DECLARATION OF CONFORMITY
Product Name : CoolX Series Product Type : Component Power Supply Model Number : CXabc-wxyz-defgh
where: CX = all CoolX part numbers start with ‘CX’ ab = 06 06 = 600W output c = S S = ITE/Industrial product w, x, y, z = 0, #, A, B, C, D, E or G
0 = Unpopulated slot; # = Unavailable slot (due to the presence of a multi-slot module in a neighboring slot); A = CmA; B = CmB; C = CmC; D = CmD; E = CmE; G = CmG
d = N; C; S; P or X N = Standard model (Unconfigured) C = Conformal Coating S = Ruggedised + Conformal Coating P = Configured
X = Internal use only e = ‘-‘; 0 – 9 or A-Z
‘-‘ = Screw Terminal (Standard) 1 = IEC Terminal
4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage A–Z = Other connector options (cables etc) f = A or B A = 12V Aux output (standard) B = 5V Aux output g = Not used; ‘-‘ or L Not used = Standard model (if h is not used)
‘-‘ = Standard model (if h is used) L = Cover h = Optional. Any alphanumeric character. Logistic use only.
Excelsys Technologies Ltd. 27 Eastgate Drive Eastgate Business Park Little Island Co. Cork, Ireland Tel: + 353 21 4354716 Fax: + 353 21 4354864
Doc No: 41024 rev. 01 - Declaration of Conformity CoolX Series 60950-1 & 62368-1 Prepared: S. I. Cionca Date: 11th August 2017
Excelsys Technologies Ltd. confirms that this product conforms to: Safety Safety of Information Technology Equipment: EN 60950-1: 2006 / A11: 2009 / A1: 2010 / A12: 2011 / A2:2013 and EN 62368-1: 2014 Supplementary Information Safety tests were conducted by TÜV Rheinland InterCert Kft. By conformance with the standards referenced, the product follows the provisions of EC Directive 2014/35/EU (Low Voltage Directive) with the exception of the enclosure requirement. These products are only for inclusion by professional installers within other equipment and must not be operated as stand alone products. These power supplies provide REINFORCED INSULATION between input and output and may be used as an SELV circuit or a TNV power source which is insulated from the AC mains. The maximum ambient temperature must not exceed 40ºC at full load. Place of Issue: Cork, Ireland For and on behalf of Date of Issue: 11th August 2017 Excelsys Technologies Limited
Dermot Flynn
Page 1 of 2 55000048B
CE Declaration of Conformity CoolX Series Component Power Supply
Year of Issue: 2019
Applicable Directives:
2014/35/EU - Low Voltage Directive - Laws for electrical equipment within certain voltage limits
Applicable Standards:
EN 62368-1: 2014 Safety of Audio/video, information and communication technology equipment + C1:2015 +C2: 2015
EC 60950-1: 2005 Safety of Information Technology Equipment +C1:2006 + C2:2013 + AMD1:2009 + C1:2012 + AMD2:2013
NOTE:
1. The EMC and Safety compliance described is only for the equipment listed in this declaration. When this equipment is installed in a system, the end-user is responsible to ensure both the EMC and Safety compliance of the overall system.
2. This equipment must be installed and used in accordance with all the “conditions of use” described in the user Manual.
3. Do not modify or expand this equipment without official permission and direction of Advanced Energy Industries Inc.
4. Failure to follow any of these requirements makes this declaration invalid.
Declared Model Numbers:
CXabc-uvwxyz-defgh
CX – all CoolX part numbers begin with CX ab = 18
18 = 1800W output c = S S = ITE/Industrial product u, v, w, x, y, z = 0, #, A, B, C, D, E, F, G or H 0 = Unpopulated slot
# = Unavailable slot (due to multi-slot module in neighboring slot) A-H = A = CmA; B = CmB; C = CmC; D = CmD; E = CmE; F = CmF; G = CmG; H = CmH
d = N, C, S, P or X: N = Standard model (unconfigured) C = Conformal coating S = Ruggedized + Conformal coating P = configured X = Internal use only
e = ‘-’, 0-9, or A-Z ‘-‘ = Screw Terminal (standard) 1 = IEC Terminal 2 = Screw Terminal, Reverse Fan 3 = IEC Terminal, Reverse Fan 4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage 6 = Screw Terminal, Low Leakage, Reverse Fan 7 = IEC Terminal, Low Leakage, Reverse Fan A-Z = Other connector options (cables, etc)
f = A or B A = 12V Aux input (standard) B = 5V Aux output
g = Not Used, ‘-‘
1625 Sharp Point Drive Fort Collins, Colorado 80525 USA
Page 2 of 2 55000048B
Not used = Standard model (if h is not used) ‘-‘ = Standard model (if h is used)
h = Optional. Any alphanumeric character. Logistic use only
Authorized by: Troy Mai November 20, 2019 Troy, Mai Date VP Quality
Advanced Energy Industries, Inc.
Note: To verify the validity and relevance of this document to AE products, contact the Advanced Energy Industries, Inc.
Page 1 of 2 55000049B
CE Declaration of Conformity CoolX Series Component Power Supply
Year of Issue: 2019
Applicable Directives:
2014/35/EU - Low Voltage Directive - Laws for electrical equipment within certain voltage limits
Applicable Standards:
EN 60601-1: 2005 Safety of Medical electrical equipment + C1:2006 + C2:2007 + AMD1:2012 or IEC 60601-1:2012 + C1:2012 + C1:2014
NOTE:
1. The EMC and Safety compliance described is only for the equipment listed in this declaration. When this equipment is installed in a system, the end-user is responsible to ensure both the EMC and Safety compliance of the overall system.
2. This equipment must be installed and used in accordance with all the “conditions of use” described in the user Manual.
3. Do not modify or expand this equipment without official permission and direction of Advanced Energy Industries Inc.
4. Failure to follow any of these requirements makes this declaration invalid.
Declared Model Numbers:
CXabc-uvwxyz-defgh
CX – all CoolX part numbers begin with CX ab = 18
18 = 1800W output c = M M = Medical Product u, v, w, x, y, z = 0, #, A, B, C, D, E, F, G or H 0 = Unpopulated slot
# = Unavailable slot (due to multi-slot module in neighboring slot) A-H = A = CmA; B = CmB; C = CmC; D = CmD; E = CmE; F = CmF; G = CmG; H = CmH
d = N, C, S, P or X: N = Standard model (unconfigured) C = Conformal coating S = Ruggedized + Conformal coating P = configured X = Internal use only
e = ‘-’, 0-9, or A-Z ‘-‘ = Screw Terminal (standard) 1 = IEC Terminal 2 = Screw Terminal, Reverse Fan 3 = IEC Terminal, Reverse Fan 4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage 6 = Screw Terminal, Low Leakage, Reverse Fan 7 = IEC Terminal, Low Leakage, Reverse Fan A-Z = Other connector options (cables, etc)
f = A or B A = 12V Aux input (standard) B = 5V Aux output
g = Not Used, ‘-‘ Not used = Standard model (if h is not used)
1625 Sharp Point Drive Fort Collins, Colorado 80525 USA
Page 2 of 2 55000049B
‘-‘ = Standard model (if h is used) h = Optional. Any alphanumeric character. Logistic use only
Authorized by: Troy Mai November 20, 2019 Troy, Mai Date VP Quality
Advanced Energy Industries, Inc.
Note: To verify the validity and relevance of this document to AE products, contact the Advanced Energy Industries, Inc.
Page 1 of 2 55000052A
CE Declaration of Conformity CoolX Series Component Power Supply
Year of Issue: 2019
Applicable Directives:
2014/35/EU - Low Voltage Directive - Laws for electrical equipment within certain voltage limits
Applicable Standards:
EN 62368-1: 2014 Safety of Audio/video, information and communication technology equipment + C1:2015 +C2: 2015
EC 60950-1: 2005 Safety of Information Technology Equipment +C1:2006 + C2:2013 + AMD1:2009 + C1:2012 + AMD2:2013
NOTE:
1. The EMC and Safety compliance described is only for the equipment listed in this declaration. When this equipment is installed in a system, the end-user is responsible to ensure both the EMC and Safety compliance of the overall system.
2. This equipment must be installed and used in accordance with all the “conditions of use” described in the user Manual.
3. Do not modify or expand this equipment without official permission and direction of Advanced Energy Industries Inc.
4. Failure to follow any of these requirements makes this declaration invalid.
Declared Model Numbers:
CXabc-uvwxyz-defgh
CX – all CoolX part numbers begin with CX ab = 10
10 = 1000W output c = S S = ITE/Industrial product u,v,w, x, y, z = 0, #, A, B, C, D, E, F, G or H 0 = Unpopulated slot
# = Unavailable slot (due to multi-slot module in neighboring slot) A-H = A = CmA; B = CmB; C = CmC; D = CmD; E = CmE; F = CmF; G = CmG; H = CmH
d = N, C, S, P or X: N = Standard model (unconfigured) C = Conformal coating S = Ruggedized + Conformal coating P = configured X = Internal use only
e = ‘-’, 0-9, or A-Z ‘-‘ = Screw Terminal (standard) 1 = IEC Terminal 4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage A-Z = Other connector options (cables, etc)
f = A or B A = 12V Aux input (standard) B = 5V Aux output
g = Not Used, ‘-‘ or L Not used = Standard model (if h is not used) ‘-‘ = Standard model (if h is used) L = Cover
h = Optional. Any alphanumeric character. Logistic use only
1625 Sharp Point Drive Fort Collins, Colorado 80525 USA
Page 2 of 2 55000052A
Authorized by: Troy Mai November 20, 2019 Troy, Mai Date VP Quality
Advanced Energy Industries, Inc.
Note: To verify the validity and relevance of this document to AE products, contact the Advanced Energy Industries, Inc.
Page 1 of 2 55000053A
CE Declaration of Conformity CoolX Series Component Power Supply
Year of Issue: 2019
Applicable Directives:
2014/35/EU - Low Voltage Directive - Laws for electrical equipment within certain voltage limits
Applicable Standards:
EN 60601-1: 2005 Safety of Medical electrical equipment + C1:2006 + C2:2007 + AMD1:2012 or IEC 60601-1:2012 + C1:2012 + C1:2014
NOTE:
1. The EMC and Safety compliance described is only for the equipment listed in this declaration. When this equipment is installed in a system, the end-user is responsible to ensure both the EMC and Safety compliance of the overall system.
2. This equipment must be installed and used in accordance with all the “conditions of use” described in the user Manual.
3. Do not modify or expand this equipment without official permission and direction of Advanced Energy Industries Inc.
4. Failure to follow any of these requirements makes this declaration invalid.
Declared Model Numbers:
CXabc-uvwxyz-defgh
CX – all CoolX part numbers begin with CX ab = 10
10 = 1000W output c = M M = Medical Product u, v, w, x, y, z = 0, #, A, B, C, D, E, F, G or H 0 = Unpopulated slot
# = Unavailable slot (due to multi-slot module in neighboring slot) A-H = A = CmA; B = CmB; C = CmC; D = CmD; E = CmE; F = CmF; G = CmG; H = CmH
d = N, C, S, P or X: N = Standard model (unconfigured) C = Conformal coating S = Ruggedized + Conformal coating P = configured X = Internal use only
e = ‘-’, 0-9, or A-Z ‘-‘ = Screw Terminal (standard) 1 = IEC Terminal 4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage A-Z = Other connector options (cables, etc)
f = A or B A = 12V Aux input (standard) B = 5V Aux output
g = Not Used, ‘-‘ or L Not used = Standard model (if h is not used) ‘-‘ = Standard model (if h is used) L = Cover
h = Optional. Any alphanumeric character. Logistic use only
1625 Sharp Point Drive Fort Collins, Colorado 80525 USA
Page 2 of 2 55000053A
Authorized by: Troy May November 20, 2019 Troy, Mai Date VP Quality
Advanced Energy Industries, Inc.
Note: To verify the validity and relevance of this document to AE products, contact the Advanced Energy Industries, Inc.
EU REACH Disclosure: 205 Substances of Very High Concern Considered
Excelsys CoolX Series CoolX600, CoolX1000, CoolX1800 AC/DC Power Supplies 100 - 240 VAC universal input, 4 & 6 slot modular DC output, 600W, 1000W, 1800W max. All options: ITE, medical, low-leakage, aux output
Issued: March 3, 2020
Manufactured by Excelsys Technologies Ltd., an Advanced Energy Company Doc No: 41017 27 Eastgate Business Park | Little Island, Cork | Ireland | +353.0.21.4354716 rev. 01
Advanced Energy Industries, Inc. 1625 Sharp Point Drive | Fort Collins, CO 80525 | USA |+1 970 221 4670 | advanced-energy.com Page 1 of 3
REACH: Registration, Evaluation, Authorization and Restriction of Chemicals Regulation (EC) No. 1907/2006
REACH is the European Union’s chemical substances regulatory framework.
Excelsys, an Advanced Energy company, does not produce chemical substances or mixtures but does manufacture electrical and electronic equipment that might contain REACH substances in component parts of the final product.
Article 33 of REACH requires manufacturers to inform customers of Substances of Very High Concern (SVHCs) when contained in component parts of their product at concentrations above 0.1% by weight. SVHCs are listed in the Authorization Candidate list of Annex XIV. Sufficient SVHC information must be provided to the customer to allow for safe use.
Article 67 of REACH describes restricted substances that manufacturers are limited or banned from being placed on the market, as detailed in the Restricted Substances List in Annex XVII.
Based on information from component part manufacturers, suppliers, third-party databases, and review of each individual component part within this product, Excelsys, an Advanced Energy company discloses the following:
Article 67 Disclosure: Products listed DO NOT contain any Restricted Substances per Article 67, as listed in Annex XVII.
Article 33 Disclosure: Products listed contain at least one SVHC in Candidate List of Annex XIV above concentration of 0.1%:
SVHC Name CAS Number Location & Safe Use Lead 7439-92-1 SVHCs listed are in various electronic components of
this product and DO NOT present hazards to humans or the environment under normal handling and use. Do not cut open or crush components.
Lead Monoxide (Lead Oxide) 1317-36-8 4,4'-isopropylidenediphenol (BPA, Bisphenol A)
80-05-7 .
REACH review of product conducted under the following conditions:
European Chemicals Agency (ECHA) SVHC candidate list:
January 16, 2020 publication date: 205 SVHCs
Authorized by: Type of product manufactured, per REACH definition:
Complex article assembled from many compo-nent articles, electrical & electronic equipment
J.D. Johnson Environmental Compliance Manager
Subject to REACH Article 7, ECHA registration ?:
No, substances in articles < 1 tonne per year No, substances not intended to be released
SVHC concentration of > 0.1%, calculation method:
SVHC weight divided by weight of part containing SVHC, per European Court of Justice ruling
EU REACH Disclosure: 201 Substances of Very High Concern Considered
Issued: March 3, 2020
Manufactured by Excelsys Technologies Ltd., an Advanced Energy Company Doc No: 41017 27 Eastgate Business Park | Little Island, Cork | Ireland | +353.0.21.4354716 rev. 02
Advanced Energy Industries, Inc. 1625 Sharp Point Drive | Fort Collins, CO 80525 | USA |+1 970 221 4670 | advanced-energy.com Page 2 of 3
Product Declared Compliant: CoolX Series Power Supplies
CoolX configured power supply part numbering system: Part Number = CXabc-uvwxyz-defgh CX = all CoolX part numbers start with ‘CX’
ab = 06, 10,18 CoolPac cabinet with AC input, slots for CoolMods: 06 = 600W output - with 4 slots, no cooling fan 10 = 1000W output - with 6 slots, no cooling fan 18 = 1800W output - with 6 slots, variable speed fan
c = S or M S = ITE/Industrial product M = Medical product
u, v, w, x, y, z = CoolMod plug-in DC output modules starting with Cm: 0, #, or A - Z 0 = Unpopulated slot # = Unavailable slot (due to multi-slot module in neighboring slot) A = CmA E = CmE B = CmB F = CmF C = CmC G = CmG D = CmD H = CmH
d = N, C, S, P, or X N = Standard model (Unconfigured) C = Conformal Coating S = Ruggedised, including conformal coating P = Configured X = Internal use only
e = ‘-‘, 0 - 9 or A - Z ‘-‘ = Screw Terminal (Standard), normal leakage 1 = IEC Terminal 2 = Screw Terminal, Reverse Fan 3 = IEC Terminal, Reverse Fan 4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage 6 = Screw Terminal, Low Leakage, Reverse Fan 7 = IEC Terminal, Low Leakage, Reverse Fan A - Z = Other connector options (cables etc.) f = A or B A = 12V Aux output (standard) B = 5V Aux output
EU REACH Disclosure: 201 Substances of Very High Concern Considered
Issued: March 3, 2020
Manufactured by Excelsys Technologies Ltd., an Advanced Energy Company Doc No: 41017 27 Eastgate Business Park | Little Island, Cork | Ireland | +353.0.21.4354716 rev. 02
Advanced Energy Industries, Inc. 1625 Sharp Point Drive | Fort Collins, CO 80525 | USA |+1 970 221 4670 | advanced-energy.com Page 3 of 3
g = Not used, ‘-‘, or A-Z Not used = Standard model, end of part number (h is not used) ‘-‘ = Standard model with h options (- used when h is used) A-Z = Reserved for internal use (not standard software variants) L = Cover, not standard
h = Optional Any alphanumeric character. Logistics use only.
Product Declared Compliant: CoolMod modules, for CoolX Power Supplies
CoolX CoolMod plug-in modules part numbering system Part Number = Cma-bcd Cm = all CoolMod part numbers start with ‘Cm’ a = A - Z Type of CoolMod module: Standard, High power, Dual Output, or Wide Trim See Note below
‘-‘ = Not used, ’-‘, Not used = Standard model, end of part number (bcd is not used) P, C, or S ‘-‘ = Standard model with bcd options (- used when bcd is used) P = Specific output adjustment settings C = Conformal Coating S = Ruggedised, including conformal coating
bcd = Optional Any three alphanumeric characters. Logistics use only. Note: Use ‘-‘ to designate standard model when bcd is used. Example: CmB-X03 Not used when bcd is not used, end of part number. Example: CmB
EU RoHS Declaration of Conformity EU RoHS 2 + RoHS 2.1 (RoHS 3)
Excelsys CoolX Series CoolX600, CoolX1000, CoolX1800 AC/DC Power Supplies 100 - 240 VAC universal input, 4 & 6 slot modular DC output, 600W, 1000W, 1800W max. All options: ITE, medical, low-leakage, aux output
Issued: March 4, 2020
Manufactured by Excelsys Technologies Ltd., an Advanced Energy Company Doc No: 41016 27 Eastgate Business Park | Little Island, Cork | Ireland | +353.0.21.4354716 rev. 04
Advanced Energy Industries, Inc. 1625 Sharp Point Drive | Fort Collins, CO 80525 | USA |+1 970 221 4670 | advanced-energy.com Page 1 of 3
Excelsys, an Advanced Energy company, declares the product listed above is in conformity with:
EU Directive 2011/65/EU - RoHS 2 Restriction of the use of certain Hazardous Substances in electrical and electronic equipment
Delegated Directive (EU) 2015/863 - RoHS 2.1 (RoHS 3)
Amendment to Annex II of Directive 2011/65/EU (RoHS 2) regarding the list of restricted substances, adding four phthalates
This product is EU RoHS 2 and EU RoHS 2.1 compliant, containing no more than the maximum concentration of hazardous substances listed in amended Annex II, with possible use of Lead permitted by exemptions 6(c), 7(a), 7(c)-I, and 15 of Annex III. Amended Annex II hazardous substances
Lead (Pb) Polybrominated biphenyl ethers (PBDE) Mercury (Hg) Bis(2-ethylhexyl) phthalate (DEHP) Cadmium (Cd) Butyl benzyl phthalate (BBP) Hexavalent Chromium (Cr+6) Dibutyl phthalate (DBP) Polybrominated biphenyls (PBB) Diisobutyl phthalate (DIBP)
This declaration of conformity is issued under the sole responsibility of the manufacturer.
Product models, subassemblies and accessories covered under this declaration listed on following pages.
EU RoHS Declaration of Conformity EU RoHS 2 + RoHS 2.1 (RoHS 3)
Issued: February 20, 2020
Manufactured by Excelsys Technologies Ltd., an Advanced Energy Company Doc No: 41016 27 Eastgate Business Park | Little Island, Cork | Ireland | +353.0.21.4354716 rev. 04
Advanced Energy Industries, Inc. 1625 Sharp Point Drive | Fort Collins, CO 80525 | USA |+1 970 221 4670 | advanced-energy.com Page 2 of 3
Product Declared Compliant: CoolX Series Power Supplies
CoolX configured power supply part numbering system: Part Number = CXabc-uvwxyz-defgh CX = all CoolX part numbers start with ‘CX’
ab = 06, 10,18 CoolPac cabinet with AC input, slots for CoolMods: 06 = 600W output - with 4 slots, no cooling fan 10 = 1000W output - with 6 slots, no cooling fan 18 = 1800W output - with 6 slots, variable speed fan
c = S or M S = ITE/Industrial product M = Medical product
u, v, w, x, y, z = CoolMod plug-in DC output modules starting with Cm: 0, #, or A - Z 0 = Unpopulated slot # = Unavailable slot (due to multi-slot module in neighboring slot) A = CmA E = CmE B = CmB F = CmF C = CmC G = CmG D = CmD H = CmH
d = N, C, S, P, or X N = Standard model (Unconfigured) C = Conformal Coating S = Ruggedised, including conformal coating P = Configured X = Internal use only
e = ‘-‘, 0 - 9 or A - Z ‘-‘ = Screw Terminal (Standard), normal leakage 1 = IEC Terminal 2 = Screw Terminal, Reverse Fan 3 = IEC Terminal, Reverse Fan 4 = Screw Terminal, Low Leakage 5 = IEC Terminal, Low Leakage 6 = Screw Terminal, Low Leakage, Reverse Fan 7 = IEC Terminal, Low Leakage, Reverse Fan A - Z = Other connector options (cables etc.)
f = A or B A = 12V Aux output (standard) B = 5V Aux output
EU RoHS Declaration of Conformity EU RoHS 2 + RoHS 2.1 (RoHS 3)
Issued: February 20, 2020
Manufactured by Excelsys Technologies Ltd., an Advanced Energy Company Doc No: 41016 27 Eastgate Business Park | Little Island, Cork | Ireland | +353.0.21.4354716 rev. 04
Advanced Energy Industries, Inc. 1625 Sharp Point Drive | Fort Collins, CO 80525 | USA |+1 970 221 4670 | advanced-energy.com Page 3 of 3
g = Not used, ‘-‘, or A-Z Not used = Standard model, end of part number (h is not used) ‘-‘ = Standard model with h options (- used when h is used) A-Z = Reserved for internal use (not standard software variants) L = Cover, not standard
h = Optional Any alphanumeric character. Logistics use only.
Product Declared Compliant: CoolMod modules, for CoolX Power Supplies
CoolX CoolMod plug-in modules part numbering system Part Number = Cma-bcd Cm = all CoolMod part numbers start with ‘Cm’ a = A - Z Type of CoolMod module: Standard, High power, Dual Output, or Wide Trim See Note below
‘-‘ = Not used, ’-‘, Not used = Standard model, end of part number (bcd is not used) P, C, or S ‘-‘ = Standard model with bcd options (- used when bcd is used) P = Specific output adjustment settings C = Conformal Coating S = Ruggedised, including conformal coating
bcd = Optional Any three alphanumeric characters. Logistics use only. Note: Use ‘-‘ to designate standard model when bcd is used. Example: CmB-X03 Not used when bcd is not used, end of part number. Example: CmB
Authorized by:
J.D. Johnson Environmental Compliance Manager