Varies - See Table
Please refer to the technical note: Installer guidance for quilt insulation in Elite Wall Systems
Refer to Technical for advice on constructions requiring better U values than those shown.
Please Note:
System is fire rated using Knauf Factoryclad 40 ECOSE insulation of minimum thickness 80mm with steel outer sheet only, to achieve 120 minutes Integrity, 15 minutes
(min) Insulation which meets the requirements of Building Regulations Part B for external walls where fire attack is from inside the building and the wall is 1M or more
from the boundary.
System can be fire rated using Rockwool insulation of minimum thickness 120mm with steel outer sheet only, with liner stitched at 300mm centres, to achieve 120
minutes Integrity, 30 minutes (min) Insulation.
Ensure roll edges are lapped/butted to ensure no gaps.
Opus plank to be installed from top down.
*
*
*Fixings with an asterix are required on sheet ends and end laps only.
Elite System 58
Bracket Height
Insulation
Thickness
Insulation Value
Overall System
Depth
U Value at 1.5M
Centres
120mm
140mm
160mm
180mm
200mm
220mm
120mm
140mm
160mm
180mm
200mm
220mm
0.36
0.31
0.27
0.24
0.22
0.20
100mm 100mm 0.040 0.43
0.040
0.040
0.040
0.040
0.040
0.040
145mm
165mm
185mm
205mm
225mm
245mm
125mm
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
1 of 18
COLOUR SIDE
0.9mm Aluminium
15
50
3,5
0.9mm Aluminium or
0.7mm Steel
Opus Edge Retention
0.7mm Steel
50
15
3,5
Euroclad EC Opus 25_150
or Euroclad EC Opus
25_200 0.7mm Steel
0.9mm Aluminium Sheet
Side lap detail
ELITE SYSTEM 58 VERTICAL JOINT DETAIL
ELITE SYSTEM 58 HORIZONTAL JOINT DETAIL
50mm x 1mm butyl sealing tape
Quattro brackets to required depth
rails typically @ 1167mm centres
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
Quattro brackets to required depth
rails typically @ 1167mm centres
4mm Bead class A
butyl sealant
Secondary Quattro rail fixed
to allow for tolerance
Please Note:
System is fire rated using Knauf Factoryclad 40 ECOSE insulation of minimum thickness
80mm with steel outer sheet only, to achieve 120 minutes Integrity, 15 minutes (min)
Insulation which meets the requirements of Building Regulations Part B for external walls
where fire attack is from inside the building and the wall is 1M or more from the boundary.
System can be fire rated using Rockwool insulation of minimum thickness 120mm with
steel outer sheet only, with liner stitched at 300mm centres, to achieve 120 minutes
Integrity, 30 minutes (min) Insulation.
Ensure roll edges are lapped/butted to ensure no gaps.
COLOUR SIDE
COLOUR SIDE
0.9mm Aluminium
15
50
3,5
0.9mm Aluminium or
0.7mm Steel
Opus Edge Retention
0.7mm Steel
50
15
3,5
Opus plank to be installed from top down.
Min 60
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Euroclad EC
19-167-1000 Liner
19_2L 0.4mm Steel
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel Side Lap
Euroclad EC Opus 25_150
or Euroclad EC Opus
25_200 0.7mm Steel
0.9mm Aluminium Sheet
Side lap detail
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
2 of 18
Plank 200mm Module
22.2
2.4
16.5
19.8
24.6
12.7
35.1
197
12.7
22.2
2.4
19.8
24.6
12.7
16.4
35.1
190
12.7
23,50
22.2
2.4
33.50
19.8
24.6
12.7
35.1
180
12.7
3mm Gap
10mm Gap
20mm Gap
COLOUR SIDE
200
16,50
COLOUR SIDE
200
23,50
103
200
33,50
20
COLOUR SIDE
NB: Module = Face + Gap size
Gap size should be kept uniform with the
use of packers
22.2
2.4
18.5
19.8
24.6
12.7
35.1
147
12.7
COLOUR SIDE
150
16,50
3
Plank 150mm Module
3mm Gap
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
EUROCLAD EC OPUS 25-150 and EC OPUS 25-200 0.7mm Steel 0.9mm Aluminium EXTERNAL SHEET
3 of 18
COLOUR SIDE
COLOUR SIDE
167167
104
19
R
4
22
2
8
1
3
7
°
1
0
1000
18
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
EUROCLAD EC 19-167-1000 Liner 19_2L 0.4mm LINER
4 of 18
40
Brackets less than 260mm require
2 fixings diagonally opposite.
Brackets 260mm or more require
4 fixings.
< 260mm
≥ 260mm
40
33
34
60
59
VARIES D
EPEN
DIN
G
ON
BRACKET H
EIG
HT
VARIES D
EPEN
DIN
G
ON
BRACKET H
EIG
HT
SIDE ELEVATION
Maximum bar cantilever at free
ends is 300mm.
Spigot can fall anywhere between
two brackets.
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
5 of 18
Quattro brackets to required depth
rails typically @ 1167mm centres
Fixings in every Opus panel
Euroclad Elite Insulation
Drip Flashing with variable leg
to allow tolerance
Euroclad EC 19-167-1000
Liner 19_2L 0.4mm Steel
Insulation
Liner Flashing fillers fixed and sealed to liners to
provide air tightness and vapour control
Fixing through Rail and
Quattro bracket to prevent
the Rail slipping
Liner fixing in every
pan on tail lines
Soft Joint to assist the
provision of air tightness
Variable
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
6 of 18
Quattro brackets to required depth
rails typically @ 1167mm centres
Fixings in every Opus Panel
Drip Flashing with variable leg
to allow tolerance
Masonry
Euroclad Elite Insulation
Liner Flashing fillers fixed and sealed to liners to
provide air tightness and vapour control
Fixing through Rail and
Quattro bracket to prevent
the Rail slipping
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Soft Joint to assist the
provision of air tightness
Variable
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
7 of 18
Fixings in every Opus Panel
Euroclad Elite Insulation
Drip Flashing with variable leg
to allow tolerance
Window / Door Head
Flashing
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Liner Flashing fillers fixed and sealed to liners to
provide air tightness and vapour control
Insulation
Flashing fixed and sealed to
internal elements
Variable
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
8 of 18
Quattro brackets to
required depth rails typically
@ 1167mm centres
Fixings in every Opus Panel
Euroclad Elite Insulation
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Mastic Seal
Flashing with variable leg
to allow tolerance
Liner Flashing fillers fixed and sealed to liners to
provide air tightness and vapour control
Window Cill
Packer
Variable
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
9 of 18
Fixings in every Opus Panel
Euroclad Elite Insulation
Drip Flashing with variable leg
to allow tolerance
Window / Door Head
Flashing
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Liner Flashing fillers fixed and sealed to liners to
provide air tightness and vapour control
Insulation
Flashing fixed and sealed to
internal elements
Variable
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
10 of 18
Euroclad Elite Insulation
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Quattro brackets to required depth
rails typically @ 1167mm centres
Quattro bar and bracket
Profile Filler
Bracket Fixed @ 150 ( max ) centres
using stitcher screws or self sealing rivets
Closer Flashing sealed
and stitched to Europlank
Profile Filler air seal
between liner and rail
Gallows Gutter Bracket
Colorcoat gutter by Euroclad
Architectural Fabrications to detail
Note: Opus plank to be installed from top down.
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
11 of 18
Flashing
Profile Filler
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Insulation
Euroclad EC 32-167-1000 Roof 32_1F
0.7mm steel
Quattro brackets to required depth
rails typically @ 1167mm centres
Fixing through Rail and
Quattro bracket to prevent the Rail slipping
Closer Flashing Sealed
and stitched to sheet
Note: Opus plank to be installed from top down.
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
12 of 18
H
300mm
MAX
300m
m
MAX
25
25
Face fixed reverse box flashing
Secret fixed box flashing
Face fixed flashing
Euroclad Elite Insulation
Quattro brackets to required depth
rails typically @ 1167mm centres
Profile Filler
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Euroclad Flashing
Internal Flashing with seals
Secondary Quattro rail fixed
to allow for tolerance
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
Please contact Euroclad OSR
department regarding limitations
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
13 of 18
Euroclad Flashing
Window Detail
Euroclad Flashing Support
Profile Filler
Quattro brackets to required depth
rails typically @ 1167mm centres
Euroclad Elite Insulation
Flashing sealed to provide air tightness
and vapour control
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Anti cold bridge insulation
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
14 of 18
Quattro brackets to required depth
rails typically @ 1167mm centres
Profile Filler
Flashing sealed to provide air tightness
and vapour control
Euroclad Elite Insulation
Door Detail
Flashing
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Insulation
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
15 of 18
Quattro brackets to required depth
rails typically @ 1167mm centres
Profile Filler
Flashing sealed to provide air tightness
and vapour control
Euroclad Elite Insulation
Door Detail
Flashing
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Insulation
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
16 of 18
Secondary Quattro rail fixed
to allow for tolerance
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Profile Filler
Euroclad Top Hat Detail
Euroclad Elite Insulation
20
27
30
0.7mm, 0.9mm
decorative top hat
Please Note: The vertical joint detail is required to maintain
continuity of the external metal skin to achieve fire rating
performance of 120 minutes Integrity, 15 minutes (min) Insulation.
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
17 of 18
Quattro Bracket to required
depth typically @ 1167mm centres
Internal flashing fixed and sealed
to provide air tightness
9x3mm Mastic Sealant
Internal Flashing
9x3mm Mastic Sealant
Quattro Bracket to required
depth typically @ 1m centres
Euroclad EC 19-167-1000 Liner
19_2L 0.4mm Steel
Euroclad EC Opus 25_150 or
Euroclad EC Opus 25_200 0.7mm
Steel 0.9mm Aluminium
TITLE: Elite System 58
DWG NO: E58
DRAWN: CD
DATE: Jan 2020
CHECK: MP
SCALE: NTS
ELITE SYSTEMS
To be read in conjunction with
Elite System specification
documents
This draft drawing has been
supplied by Euroclad Group Ltd
for the purpose of guidance free
of charge. It is a suggested
typical detail and as such should
not be assumed suitable for any
specific project or application.
No responsibility is assumed for
errors or misinterpretations
resulting from the information
contained in the drawing. Details
are for illustration only and no
liability is accepted. We reserve
the right to change the details
without notice.The drawing is
copyright, it remains our
property.
www.euroclad.com
Tel: +44 (0)2922 010 101
Fax: +44 (0)2922 010 122
18 of 18