Download - EMDEC troubleshooting tool
-
8/10/2019 EMDEC troubleshooting tool
1/376
Electro-MotiveDiesel Engine
EMDECOperating &
Troubleshooting
Guide
-
8/10/2019 EMDEC troubleshooting tool
2/376
-
8/10/2019 EMDEC troubleshooting tool
3/376
Acknowledgments
The EMDEC Operating & Troubleshooting Guide has been preparedfor use by qualified personnel engaged in the maintenance and repair ofelectronic fuel injection systems on Electro-Motive diesel engines.
Always refer to the correct electrical schematic for the specific application.
NOTE:
To ensure compliance with emission standards and warranty
conditions, use only by O.E.M. certified replacement pads. Consult
the appropriate Service Parts Catalogue for the application.
-
8/10/2019 EMDEC troubleshooting tool
4/376
-
8/10/2019 EMDEC troubleshooting tool
5/376
Table of Contents
Introduction and System Development
1.1 INTRODUCTION .......................................11.2 REASONS FOR DEVELOPMENT
OF EMDEC ...............................................11.3 EMDEC COMPONENTS ...........................21.3.1 Engine Control Modules (ECMs) ..........2
1.3.2 Electronic Fuel Injectors (Two-stroke).... 31.3.3 Electronic Fuel Pumps & Injectors
(Four-stroke)............................................41.3.4 Sensors ....................................................51.3.5 Power Supply & Interface Module .........51.3.6 CONCLUSION ..........................................5
1.3.7 EMDEC GLOSSARY OF TERMS.................6
EUI Fuel Delivery System
2.1 INTRODUCTION .......................................92.2 THE 710 TYPE FUEL SUPPLY SYSTEM .........92.2.1 Suction Strainer ................................... 112.2.2 Fuel Pump ............................................ 112 2 3 Fuel Preheater & Primary Fuel Filters 12
Chapter 1
Chapter 2
-
8/10/2019 EMDEC troubleshooting tool
6/376
Electronic Injection Equipment -Fuel Components
3.1 INTRODUCTION .................................... 233.2 710 SERIES ELECTRONIC
UNIT INJECTOR ..................................... 233.2.1 Control Portion (Solenoid) .................. 253.2.2 Armature .............................................. 253.2.3 Hollow Poppet Valve ........................... 253.2.4
High Pressure Pump Portion ................ 263.2.5 Injector Portion .................................... 263.2.6 Fuel Flow Through The EUI ................... 263.2.7 Operation Of The EUI ........................... 283.2.7.1 Start Of Injection.................................. 293.2.7.2 Piston Rises In Cylinder ........................ 30
3.2.7.3 Fueling Decisions................................. 303.2.7.4 Injection ............................................... 303.2.7.5 Bleeder Passages ................................ 323.2.7.6 End Of Injection ................................... 323.2.7.7 Injector Feedback To
The EMC (Response Time) .................. 33
3.2.7.8 Injector Response Time ....................... 343.3 H SERIES ELECTRONIC
INJECTION EQUIPMENT ........................ 343.3.1 Pump Operation.................................. 353 3 1 1 Start Of Injection Sequence 35
Chapter 3
-
8/10/2019 EMDEC troubleshooting tool
7/376
EMDEC Electronic Components & Operation
4.1 INTRODUCTION.................................... 394.2 ENGINE CONTROL
MODULES (ECMS) .............................. 414.2.1 Arrangement ...................................... 424.3 POWER SUPPLY .................................... 444.4 INTERFACE MODULE ............................ 464.5 SPEED CONTROL ................................. 474.5.1 Speed Control - One-Way Serial
Link (Locomotive Application) .......... 474.5.2 Speed Control - Two-Way Serial
Link (Locomotive Application) .......... 484.5.3 Speed Control (Marine
Application) ........................................ 484.5.4
Speed Control (PowerGeneration) ........................................ 484.6 SENSORS .............................................. 514.6.1 System Sensors ................................... 524.6.1.1 System Sensor Mounting
Arrangements - Early 710 Series ........ 53
4.6.1.2 Setting SRS & TRS Sensors ................... 544.6.1.3 System Sensor Mounting
Arrangements - H Series ..................... 544.6.1.4 Synchronous Reference Sensor ......... 554 6 1 5 Timing Reference Sensor 55
Chapter 4
-
8/10/2019 EMDEC troubleshooting tool
8/376
Load Control
5.1 INTRODUCTION.................................... 735.2 FUEL MAP ............................................. 755.3 CONTROLLING ENGINE SPEED ............ 765.4 % ALLOWABLE TORQUE SIGNAL .......... 78
Diagnostic Tools
6.1 INTRODUCTION.................................... 816.2 WINEMMON & PC READER
(DIAGNOSTICS WITH A LAPTOP PC) ... 826.2.1 Using The WinEMMON
Or The PC Reader Kit .......................... 836.2.2
Loading WinEMMON Software OnTo A Laptop Computer ......................... 846.2.3 Loading The PC Reader
On To A Laptop Computer ................ 866.2.3.1 To Edit The EMMON Command File .. 876.2.3.2 Connecting the WinEMMON
And The PC Reader to EMDEC .......... 876.2.3.3 Access Ports ........................................ 886.2.4 Utilizing WinEMMON & The PC
Reader Program ................................... 906 2 5 WinEMMON Main Screen 92
Chapter 5
Chapter 6
-
8/10/2019 EMDEC troubleshooting tool
9/376
6.2.8.1 Injector Rise Time .............................. 1136.2.8.2 Injector Calibration .......................... 1136.2.8.3 Calibration Process ............................. 1146.2.8.4 Injector Cut Out ................................ 115
6.2.8.5 Pulse Width ........................................ 1166.2.9 Bus Monitor......................................... 1176.2.10 Miscellaneous Screen ...................... 1216.2.11 Help ................................................... 1256.2.11.1 Help Topics ........................................ 1276.2.11.2 Faults ...................................................1326.3.1 PC Reader Main Screen ......................1386.3.1.1 ECM Data Boxes ............................... 1386.3.1.2 Engine Parameter Data Box ............ 1396.3.1.3 Editing The Main Screen .................. 1426.3.1.4 Injector Response Time ....................... 1446.3.1.5
Using The Injector Screen ................ 1446.3.1.6 Fault Data ......................................... 1456.3.2 Using The Diagnostics Screen.......... 1466.3.2.1 To View The Faults............................... 1476.3.2.2 To Save Archived Faults To A
File (EMDEC Fault Download) .......... 147
6.3.3 Using The Download Function ............ 1486.3.4 Using The Sensor A/D
Value Screen .................................... 1576.3.5 Using The Digital I/O Pins ................. 1586 3 6 Other PC Reader Functions 159
Chapter 6cont.
-
8/10/2019 EMDEC troubleshooting tool
10/376
Chapter 6cont.
6.4.1.4 Low Water Pressure Light ......................1656.4.1.5 Crankcase Pressure Light .....................1666.4.1.6 System Reset........................................1666.4.1.7 Engine Diagnostic Lights ......................1676.4.1.8 Stop Engine Light (SEL) ........................1676.4.1.9 Check Engine Light (CEL) .................... 1686.4.1.10 Fuel Injection Switch ............................ 1686.4.1.11 System Ready Light ..............................1696.4.1.12 Code/Test Switch ................................1706.4.2 Reading Diagnostic Codes
- Flash Method..................................... 1706.4.3 EMDEC Diagnostic Codes ...................172
Maintenance Procedures
7.1 EMDEC Injector Change-Out And
Setting Procedures.............................. 1797.1.1 Change-out And Setting
Procedures For 710 Series Electronic
Unit Injectors (Including Timing
Procedures) ...................................... 1797.1.1.1 Removing Existing Injectors
From Engine ...................................... 1797.1.1.2 Installing New Injectors In Engine .... 1807 1 1 3 Timing The Electronic Unit Injectors 183
Chapter 7
-
8/10/2019 EMDEC troubleshooting tool
11/376
7.4 70/80/90 MAC PLATFORM STYLE FUELSYSTEM CHECK VALVE REMOVALINSTRUCTIONS ................................... 202
7.4.1 Instructions For Engines With
Filters Mounted On Right FrontCorner Of Engine - 40 PSIValve ................................................. 202
7.4.2 Instructions For Engines WithFilters Mounted On Right FrontCorner Of Engine - 120 PSI Check
Valve ................................................. 2037.4.3 Instructions For Engines WithCenter Mounted Filters -120 PSI or 40 PSI Check Valve .......... 206
7.5 REPLACING EMDEC TERMINALS ........ 2087.5.1 Airbox Pressure (MAP) Sensor .......... 2087.5.2
Engine Protector ............................... 2097.5.3 Remaining Sensors And AllConnectors Into The ECM ................ 210
7.5.4 Power And Sensor Harness
Connectors - 12 Cylinder Engines ... 2117.5.5 Sensor Harness Connector - 16
Cylinder Engines ............................... 2127.5.6 Power Harness Connector - 16
Cylinder Engines ............................... 2137.5.7 Pig-Tail Temperature Sensor Plug .... 2137.5.8 AMP Plugs At Power Supply
Chapter 7cont.
-
8/10/2019 EMDEC troubleshooting tool
12/376
Chapter 8cont.
8.2.1.4 Check Fuel Pump Operation ........... 2198.2.1.5 Check Magnetic Pickups (TRS/SRS).... 2198.2.1.6 Check For Active Communication
Failures ............................................... 220
8.2.1.7 Check Plug Connections ................. 2208.2.1.8 Check For Injector/Sensor
Harness Grounds .............................. 2218.2.1.9 Check Turbocharger ........................ 2218.2.1.10 Replace ECM Module ...................... 2218.2.2 Unit Not making Horsepower ........... 2228.2.2.1 Check For EngineR Value ................ 2228.2.2.2 Check The Individual Injector
Response Time.................................. 2228.2.2.3 Check The Inlet Fuel Pressure .......... 2238.2.2.4 Check Plug Connections ................. 2248.2.2.5
Check The Airbox Sensor(MAP Sensor) .................................... 2248.2.2.6 Check The Injectors.......................... 2258.2.3 Unit Loading At 90%.......................... 2258.2.3.1 Check For EMDEC
Communication Faults..................... 225
8.2.4 Throttle Request Problems................ 2278.2.4.1 Check The EM2000 ........................... 2278.2.4.2 Check The Connections At The
Interface Board................................. 2278 2 5 Protective Engine Shutdown 229
-
8/10/2019 EMDEC troubleshooting tool
13/376
Chapter 8cont.
8.3.1 No Lights On 24V Power Supply....... 2378.3.2 Red Light Glows On 24V
Power Supply .................................... 2378.4 EMDEC WIRING VISUAL INSPECTION 2398.4.1 Open Circuit ..................................... 2398.4.2 Short Circuit ...................................... 2398.5 TROUBLESHOOTING TRS & SRS .......... 2408.5.1 Troubleshooting The TRS/SRS
Sensor Circuit .................................... 2408.6
TROUBLESHOOTING SENSORCIRCUITS ............................................ 2428.6.1 General Information ......................... 2428.6.2 Troubleshooting The Crankcase
Pressure Detector Circuit
Switch Output ................................... 243
8.6.3 Troubleshooting The AnalogCrankcase Pressure Sensor
Circuit (Analog Output) ................... 2468.6.4 Troubleshooting The Coolant
Pressure Circuit ................................. 2508.6.5 Troubleshooting The Coolant
Pressure Circuit ................................. 2538.6.6 Troubleshooting The Oil Pressure
Circuit ................................................ 2568.6.7 Troubleshooting The Oil
Pressure Circuit 259
-
8/10/2019 EMDEC troubleshooting tool
14/376
Chapter 8cont.
8.10 TROUBLESHOOTING FLOWCHARTS ... 2708.10.1 Fault Code 994 ................................. 2708.10.2 Fault Code 996 ................................. 2738.10.3 Fault Code 997 ................................. 2768.10.4 Fault Code 998 ................................. 2798.10.5 Fault Code Generic.......................... 2828.10.6 710 Engine Starting Problems .......... 2908.11 EMDEC TROUBLESHOOTING
QUICK REFERENCE GUIDE ................. 301
System References ComponentLocator Charts
A.1 EMDEC QUICK LOCATOR CHART ..... 307
EM2000 EMDEC Signal Acronyms
B.1 EM2000 EMDEC SIGNAL
ACRONYMS ....................................... 315
B.2 EMDEC ACRONYMS .......................... 320
System References
Appendix A
Appendix B
Appendix C
-
8/10/2019 EMDEC troubleshooting tool
15/376
1
Introduction &System Overview
INTRODUCTION
1.1 This manual has been prepared for personnel involvedin the maintenance and repair of the General Motors
EMDEC (Electro-Motive Diesel Engine Control)fuel injection system. This electronically-controlledfuel delivery system is currently available for the 710series, and 265H series diesel engines, and as a retrofitto appropriate older engines. EMDEC is applicable torail, power, marine, and industrial applications.
This text is intended to provide a solid workableknowledge of the basic EMDEC system, itscomponents, operation, and troubleshooting.
Due to the significant variations between equipmentapplications, the system used in this presentationreflects a basic configuration. Always refer to thecorrect Engine Maintenance Manual (EMM), andwiring schematic for specific service data.
EMDEC system diagnostics may be performed usinga laptop computer with a diagnostic program calledWIN-EMMON, and in some locomotiveapplications, by using the EM2000 control computer.This text will illustrate diagnostic techniques for both
-
8/10/2019 EMDEC troubleshooting tool
16/376
ECMs
INJECTORS
SENSORS
An additional benefit is the ease with which the systemcan be modified. By altering the programming withinthe control modules, the same physical componentscan be used on different engines, or for different
performance ratings.
The EMDEC system consists of several maincomponents that are common between most engineapplications. These components will be examined indetail later in the text. A brief description follows.
EMDECCOMPONENTS
1.3
1 1 C
-
8/10/2019 EMDEC troubleshooting tool
17/376
1
EMDEC equipped two-stroke EMD engines useelectronically-controlled unit injectors. The injectorsare fitted to the cylinder heads in a similar manner tothe mechanical style. However, instead of a mechanical
linkage, a wiring harness connects each injector to itscontrolling ECM.
Electronic UnitInjectors(Two-Stroke)
1.3.2
-
8/10/2019 EMDEC troubleshooting tool
18/376
Unlike the unitized injector on the 710 series ofengines, the 16V265H engines are currently equippedwith separate fuel pump and injector (nozzle)assemblies for each cylinder. Although separate
components, they function in a manner identical to theunitized assembly. Bosch manufactures the four-strokeinjection equipment to EMD specifications. Like otherEMDEC applications, all fuel pumps are connected tothe controlling ECM by an electrical harness.
Electronic FuelPumps &Injectors(Four-Stroke)
1.3.3
-
8/10/2019 EMDEC troubleshooting tool
19/376
1
Sensors
1.3.4 EMDEC uses various sensors to determine crankshaftspeed and position, system pressures, and temperatures.The sensors are connected to the ECMs by means ofexternal wiring harnesses .
The 24 volt power supply and interface moduleconverts control system voltage into a stable 24volts, as required by the EMDEC components.
In addition, the interface module allows forcommunication between the injection system and thecontrol system. Speed inputs for example, are convertedfrom the solenoid commands found on a Woodwardgovernor, into RPM requests that are understood by theEMDEC system.
EMDEC is by no means afinished system. Assystem and performance requirements change, thecomponents and programming are being refined
to better meet the needs of our customers. Olderapplications are upgraded to reflect the changesand maintain commonality of components.
Power Supply& Interface
Module
1.3.5
Conclusion
1.3.6
-
8/10/2019 EMDEC troubleshooting tool
20/376
ECM Engine Control Module.
EM2000 Locomotive control computer.
EMDEC Electro-Motive Diesel EngineControl.
Engine Ratio Expression of amount of fuel beingconsumed as a percentage of totalavailable fuel at a given engine
speed.
Engine_R Engine ratio as seen on the EM2000computer.
EUI Electronic Unit Injector
MUI Mechanical Unit Injector
Pulse Width Duration of an injection sequence,measured in degrees of crankshaft
rotation.
SRS Synchronous Reference Sensor, usedfor timing and speed signal.
EMDECGlossary OfTerms
1.3.7
-
8/10/2019 EMDEC troubleshooting tool
21/376
1
Notes:
-
8/10/2019 EMDEC troubleshooting tool
22/376
Notes:
-
8/10/2019 EMDEC troubleshooting tool
23/376
2
EUI Fuel SupplySystem
NOTE:
INTRODUCTION
In operation, the basic fuel supply systems used withEMDEC-equipped engines function similar to MUI
equipped systems. Major differences include filtration,fuel pressures, and fuel volume. This section of the textwill trace the fuel flow through two typical systems,those applied to typical 710 applications, and as appliedto the 6000 HP 265H application. Due to thedifferences between equipment, always refer to thespecific service publications for your applications.
The function of the fuel supply system is to provide theinjectors with a supply of filtered fuel in quantity, and
at pressures adequate to ensure proper performance.Figure 2.1 on the following page shows the basic systemas configured for a typical 710 engine locomotiveapplication.
2.1
THE 710 TYPEFUEL SUPPLYSYSTEM
2.2
Before performing maintenance or diagnostics on the
fuel system, ensure that the proper system schematic is
available for reference.
-
8/10/2019 EMDEC troubleshooting tool
24/376
- - - - - - - - - - - -- - - - - - -
- - - - - - - - - - - - - -- - - - - -- - - - - - - - - - - - - -
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
-
reliefvalve120psi.
(tak
esplaceofbypasssigh
tglass)
vent
suctionstrainer
600
electrically
driven
pump
thermostatic
modulating
valve
fuel
preheater
enginejacket
water
primary
fuel
filter13
bypass
valve30psi.
platform
/core
elements
nitinjectors
fuel
pressure
sensor
fuel
temperature
sensor
secondaryfu
el
filters5
(spin-on)
cold
plate
electronic
control
modules
fuelout
fuelin
-
-
-
8/10/2019 EMDEC troubleshooting tool
25/376
2
As in the MUI system, fuel is pulled from the fuel tankthrough a suctionstrainer by thefuel pump. This
strainer, mountedon the equipmentrack (figure 2.2)protects the fuelpump from anylarge debris
contained in thetank.
The fuel pump (figure 2.3) is typically mounted onthe equipment rack. The pump has been increased incapacity over MUI systems, with output between 5.5and 8 GPM depending on the application. While stillsupplied with 74 VDC from the control system, themotor carries its own inverter pack, and operates on
AC to eliminate brush and commutator maintenance.
Suction Strainer
2.2.1
Figure 2.2 Suction Strainer.
Fuel Pump
2.2.2
-
8/10/2019 EMDEC troubleshooting tool
26/376
Most EUI systems are equipped with a fuel preheaterand thermostatic modulating or AMOT valve (figure2.4). Inlet fuel temperature is monitored by this valve,which has a setting of 75 F(96 F on previous
locomotive models). Should fuel temperature dropbelow the nominal setting, fuel will be directedthrough the fuel preheater where it is warmed byengine cooling water.
Fuel next flows to the 13 micron primary fuel filters
(figure 2.4).These filters are equipped with a bypassvalve that will allow fuel to flow around the filters tothe engine, if the filters plug. Should the filters beginto plug, the pressure will increase in the line betweenthe primary filters and the fuel pump.
Fuel Preheater& Primary FuelFilters
2.2.3
PRIMARY
FUEL FILTERS
FUEL
PREHEATER
-
8/10/2019 EMDEC troubleshooting tool
27/376
2
The bypass begins to open (crack) at 25 psi, and is fullyopen at 30 psi. Any impurities in the fuel will be trappedby the secondary filters which will quickly plug.
On certain EUI applications, pressure transducers havebeen added to the filter inlet and outlet lines, connectedto the control system. Should the pressure differentialacross the primary filters exceed 25 psi, the controlsystem will indicate a plugged filter condition.
On later models without spin-on secondary fuel filters,primary filters are 5 microns and the bypass valve islocated between the fuel pump and the thermostaticvalve to direct fuel to the tank in the event of pluggedfilters.
From the primary filters, fuel now travels to a fuel blockat the bottom right front of the engine from which 3steel tubes (or flexible hoses on some applications) runvertically up to the Secondary Spinon Fuel FilterManifold. This fuel block feeds fuel to the Spin-on Fuel
Filter Manifold and receives return fuel from theengine. The 3 fuel lines coming from the block are:
Fuel Block
2.2.4
-
8/10/2019 EMDEC troubleshooting tool
28/376
In early models the fuel enters the Spin-on SecondaryFuel Filter Manifold. Depending on the application,this manifold may be:
mounted on the right front corner of the engine (figure 2.5a),
mounted on the front center of the engine (figure 2.5b),
SecondaryFuel FilterManifolds
2.2.5
-
8/10/2019 EMDEC troubleshooting tool
29/376
2
Figure 2.5b Front Mounted Filters.
NOTE:
Due to the increased fuel pressure and risk of fuel
leaks at this location, the sight glasses have been
eliminated on later EMDEC applications.
-
8/10/2019 EMDEC troubleshooting tool
30/376
NOTE:
Regardless of the mounting application, internalporting within the manifold allows the fuel to flow tothe cracking side of the high pressure filter bypassvalve, and both spin on secondary filters. Bypass valve
is located internally in the housings without sightglasses. On EUI applications, these filters have a 5micron rating. The element size has been increasedfrom previous systems to allow a greater fuel flow rate.Fuel pressure is monitored by EMDEC at this point,by means of a pressure transducer located in the upper
left-hand portion of the manifold, when facing thefront of the engine.
In previous models, if the primary fuel filters are
bypassing, the Secondary Spin-ons will quickly plug up.
Back pressure between the secondary filters and the fuel
pump will rise, causing the high pressure bypass valve to
open. Fuel will flow through the high pressure bypass
valve and from there back to the fuel tank. Unlike the
primary bypass, when the secondary filters plug, the
engine will starve for fuel causing major performance
problems. Changing of both primary and secondary fuel
filters is mandatory on all EMD engines.
-
8/10/2019 EMDEC troubleshooting tool
31/376
2
For applications with the filter mount on the frontright corner of the engine, fuel leaves the manifoldand enters a ported fuel distribution block mountedon the front center of the engine. From this fuel block,
supply lines connect to the right and left bank fuelmanifolds to supply the fuel injectors. On engineswith the filter manifold mounted in the center of theengine, fuel is routed directly to the fuel manifolds inthe top decks of the engine.
Fuel travels down the upper line of the manifold,down each bank of the engine, terminating at the lastcylinder on each side. Note that the fuel manifoldshave been increased in size to 7/8" diameter.
Each injector is supplied with fuel through fueljumpers as on MUI systems. The jumpers however,are now a flexible line with a larger diameter (figure2.6). The fuel enters the fuel injectors through a smallin-line filter element, then circulates through theinjectors internal passages. A portion of the fuel is
used for injection, the remainder is returned to thefuel tank. Note that lubrication and cooling of thefuel injector is done with this excess fuel flow as inprevious systems. For a more detailed operation of
Fuel Injectors
2.2.6
-
8/10/2019 EMDEC troubleshooting tool
32/376
Fuel now leaves the injector through the jumper lineto the lower line of the fuel manifold. In previousmodels, the return fuel flow from the manifolds isrouted through cold plates (if applied) attached to the
front face of the ECMs. The cold plates consist of ablock with milled fuel passages covered with a thinplate. As return fuel temperature is nominally 120 -140 F and does not change quickly, this fuel is used tostabilize the temperature of the ECMs.
From the cold plates, the return fuel is directed to thereturn fuel check valve.
On previous systems equipped with sight glasses, thisvalve is located under the return fuel sight glass (closestglass to the engine). On most EMDEC systems, thevalve is mounted inside the filter manifold block. Thecheck valve ensures that the system maintains back
Return Flow
2.2.7
Check Valve
2.2.8
NOTE:
This check valve may have a rating between 30 and 60psi, depending on application. Ensure that you consult the
Engine Maintenance Manual for the correct check valve
application.
-
8/10/2019 EMDEC troubleshooting tool
33/376
2
While the basic fuel supply system applied to Hengines performs the function as the 710 typesystems, there have been several major changes tothe operation.
The fuel supply system (figure 2.7) begins with the fueltank (a).
The tank is equipped with drains for the fuel side and
the retention tank portion.
Fuel is drawn up to the engine through the suctionstrainer (b) that serves to protect the fuel pumps.Certain 265H engine applications are equipped with
two fuel pumps, one electrically-driven (c), and onemechanically-driven (d).
The electric fuel pump is used for priming the engineprior to startup; normal engine operation is with themechanical pump only.
The electric fuel pump is a diaphragm-type pumpcontrolled by the EM2000 and is mounted below the
265H TYPEFUEL SUPPLYSYSTEM
2.3
Fuel Tank
2.3.1
SuctionStrainer
2.3.2
Fuel Pump
2.3.3
-
8/10/2019 EMDEC troubleshooting tool
34/376
TO
TANK
FUEL
TANK
D.MECHANICAL
FUELPUMP
EMDEC
FUELPRESSURE
SENSOR
FROM
PUMP
LBS
RBS
LBR
RBR
B.SUCTIO
N
STRAIN
ER
FUEL
TEMPERATURE
L URE
E.FUELFILTER
PRE
HEATER
DISTRIBUT
ION
BLOCK
C.ELECTRIC
LIFTPUMP
F.FUEL
DIST
BLOC
K
-
8/10/2019 EMDEC troubleshooting tool
35/376
2
The fuel filter (e) is a paper element type rated at 13microns and is equipped with a 25 psi bypass valve.Note the increased size of the filter to handle thegreater flow rate of the new system.
From the filter, fuel is transferred to the fueldistribution block (f) mounted on the front of theengine. Flow is divided at this point and directed to thesupply rails (g) running down each bank of the engine.
At each cylinder location, flexible jumpers carry asupply of fuel to the rocker box housing, then withinternal jumpers, across to the pump body.
The injection pumps use a portion of the fuel supplyfor engine operation, the remainder carries excess heatfrom the pumps back to the return side of the system.Through another set of flexible jumpers, return fuel isrouted into left and right bank return fuel rails (h). Atthe front of the engine, fuel is directed from eachreturn rail to a cold plate mounted to that banks ECMto stabilize temperatures within the unit. From thecold plates, fuel then travels to the fuel distributionblock where a return check valve ensures proper
Fuel Filter
2.3.4
FuelDistributionBlock
2.3.5
InjectionPumps
2.3.6
-
8/10/2019 EMDEC troubleshooting tool
36/376
Notes:
-
8/10/2019 EMDEC troubleshooting tool
37/376
-
8/10/2019 EMDEC troubleshooting tool
38/376
Figure 3.1 Electronic (EUI) and Mechanical (MUI) Injectors.
The EUI may be broken down into three basicsections - control, high pressure pump, and injector(figure 3.2).
CONTROL
PORTION
HIGH
PRESSUREPUMP
E Coil
Stator
Armature
-
8/10/2019 EMDEC troubleshooting tool
39/376
-
8/10/2019 EMDEC troubleshooting tool
40/376
The high pressure pump portion is made up of theplunger assembly and the injector body portion. Theplunger is operated by the camshaft through theinjector rocker mechanism, similar to a mechanical
injector. Downwards motion of the plunger is used togenerate the high pressures required for injection.Note that the diameter of the plunger is slightlysmaller than the diameter of the cylinder. The fillpassage for the pump chamber is located at the upperleft corner in the illustration. At no time is this passage
blocked by the plunger, which simply acts to displacea volume of fuel in the chamber.
The actual injector forms the lower portion of theassembly, and protrudes into the combustion
chamber. The injector is comprised of a check valve,needle valve, needle valve spring, and spray tip. Thespray tip has orifices that atomize the fuel as it isforced through the tip into the combustion chamber.
Fuel flows from the flexible jumper line to the EUI,entering through its inlet filter located in the body ofthe injector. Refer to figure 3.3 which shows the fuelflow in the EUI in the de-energized state (no
High PressurePump Portion
3.2.4
Injector Portion
3.2.5
Fuel Flow ThroughThe EUI
3.2.6
-
8/10/2019 EMDEC troubleshooting tool
41/376
3
Figure 3.3 Flow of Fuel Through EUI (no injection).
An internal passage directs fuel to the control portionof the injector, filling the armature chamber below theE coil stator. The flow of fuel through the armatureh b l h d l idi
-
8/10/2019 EMDEC troubleshooting tool
42/376
If the injector is de-energized, the poppet valve is openallowing fuel to flow upwards around it. This fueltravels into a drilled passageway to fill the highpressure pump chamber below the plunger. As in the
previous systems, it is important to note that most ofthe fuel sent through the injector is used for coolingand lubrication; only a small amount is actually usedfor injection.
The EMDEC electronic unit injector is bothelectrical and mechanical in operation. It performs thefunctions of metering and timing electronically, whilethe functions of pressurizing and atomizing are stilldone mechanically.
The metering and timing functions are controlled bythe ECMs, which fire each individual EUI at aprecise point in time for a specific duration.
This action is based on the software programcontained in the ECMs and inputs into the ECMssuch as:
speed requests from the control system via the interface module,
Operation OfThe EUI
3.2.7
-
8/10/2019 EMDEC troubleshooting tool
43/376
3
Top View of Injector
Poppet Valve Closed
Injection Cycle
Fuel Lubricating
and Cooling
Injector Plunger
High Pressure Bleed
Pass Return
Fuel Supply Flow
Fuel Return Flow
Trapped Fuel for Injection
Bleed Return Fuel
710 Cylinder Head
Adapter Collar
The easiest way to understand the operation of theEUI is to follow it through a typical injectionsequence. Refer to figure 3.4 for the flow of fuelthrough the injector during an injection sequence.
Start Of Injection
3.2.7.1
-
8/10/2019 EMDEC troubleshooting tool
44/376
-
8/10/2019 EMDEC troubleshooting tool
45/376
3
The high pressure generated in the pump chamber isalso transmitted downwards to the spray tip throughthe column of fuel and the check valve. As thepressure increases, it pushes outwards in all directions
in the tip area, including backwards against thetapered surface of the needle valve. When the pressurein the tip area has reached between 2000 psi and 2400psi, the needle valve will be lifted off its seat againstthe needle valve spring. This allows fuel to flowthrough the needle valve and the orifice holes in the
spray tip, into the cylinder.
The continued downwards motion of the plungercauses the pressure in the injector to rise to the finalworking pressure of between 16,000 psi and 18,000psi. Note that once injection has begun and the
injector has reached the final working pressure, theflow rate of the tip cannot be changed. For a givenperiod of time, the injector will deliver a measuredquantity of fuel. As with any injection system, what hasto be varied is timing (start of injection) and duration(pulse width). The injector will continue to inject fuelinto the cylinder as long as: a) the solenoid isenergized, and b) the injector plunger is movingdownwards.
-
8/10/2019 EMDEC troubleshooting tool
46/376
Top View of Injector
There are two additional passages shown in theillustration. These bleed passagesprevent the escapeof high pressure fuel to the outside of the injector.
During the high pressure process, fuel bleeds upwardsaround the EUIs plunger for lubrication. This fuel iscollected in the bleed passage and fed into the EUIsfuel return system to prevent further migration upwards.Due to the extremely high pressures involved, someleakage will take place between the components above
the injector tip. A second bleed passage gathers fuel inthis area to prevent leakage between the body portionand the lower housing. Again, this fuel is fed back to thelow pressure return system of the EUIs.
When the ECM has determined that injectionshould cease, it simply turns offthe injector byde-energizing the solenoid. This allows the armaturereturn spring to drop the armature and poppet valveagainst the bench in the lower fuel chamber.
BleederPassages
3.2.7.5
End Of Injection
3.2.7.6
-
8/10/2019 EMDEC troubleshooting tool
47/376
3
As the poppet valve opens, the high pressure fuel in thepump chamber is allowed to escape back through thevalve to the return fuel system. The pressure in thechamber drops instantly to end injection. When the
pressure coming from the pump chamber to the injectortip drops below 2000 psi, the needle valve return springpushes the needle valve back against its seat to close thepassage through the tip to the spray orifices.
Note that the check valve in the injector will not allow
the flow of fuel pressure back into the pump chamberfrom the tip. This serves several purposes. First, byretaining a certain amount of pressure in the tip (slightlybelow the injectors cracking pressure), the response timeof the injector for the next sequence is improved.Second, in the event of a leakage in the needle valve,
combustion gases will not be allowed to work their waythrough the injector into the fuel system.
The final action in the injector is the return of theplunger to its initial position. As the camshaftmechanism rotates further, the plunger return springmoves the plunger upwards to the top position. Thisupwards movement draws fuel back into the chamberfrom the poppet valve, refilling the chamber for the nextinjection sequence
-
8/10/2019 EMDEC troubleshooting tool
48/376
This feedback is called injector response time. Typicalresponse times will be in the range of 1.30 to 1.50milliseconds. Each injector will vary slightly, but allshould have approximately similar times. When
checking injector response times using a laptopcomputer, any injector with a response timesignificantly different from the rest may indicate afaulty injector or defect in the wiring harness. Theproblem must be diagnosed, and corrected before theengine is returned to service.
Although the ECMs can monitor the injectorselectronic performance, the mechanical portions arestill subject to failure requiring more in depthdiagnosis. These procedures will be covered in thesection on Troubleshooting settings and adjustments
are covered in a separate section.
The injection pump and nozzle (figure 3.6) functionin an identical manner to the electronic unit injectorfound on the 710 series of engine, however they have
now been divided into two separate, largercomponents. Theinjection pump islocated on the upper
InjectorResponse Time
3.2.7.8
H SERIESELECTRONICINJECTIONEQUIPMENT
3.3
-
8/10/2019 EMDEC troubleshooting tool
49/376
3
Pump Operation
3.3.1 Internally, the pump (figure 3.7)is similar to the pumpportion of the 710 electronic injector. The plungertravels in a chamber that is connected to the fuel supplysystem by a fill passage. Operation of the fill passage iscontrolled by the Engine Control Module, using apoppet valve mechanism with a 24 volt coil. In thede-energized state, upwards movement of the plungerdisplaces fuel from the pump chamber, back throughthe poppet valve to the supply system.
When the ECM determines that injection shouldbegin, the coil is energized to close the valve. Furtherupward movement of the plunger results inpressurization of the fuel in the chamber, which isdelivered to the nozzle through the delivery passageand check valve.
On completion ofinjection, thepoppet is de-energized torelease the fuelpressure back tothe supply system.The downward
To InjectorFuel Inlet
Start Of InjectionSequence
3.3.1.1
End Of InjectionSequence
3.3.1.2
Poppet
Valve
-
8/10/2019 EMDEC troubleshooting tool
50/376
The injector (figure 3.8)is mounted on the top of thecylinder head on the vertical centerline of the cylinder.The injector receives a supply of high pressure fuelfrom the pump through the high pressure jumper line
during the injection cycle. As the fuel pressure risesdue to the closing of the poppet valve, the pressurebuilds internally in the nozzle. When the pressure issufficient to lift the needle valve off its seat against thespring, fuel is allowed to flow into the engine cylinderthrough the spray tip. The fuel is atomized and mixes
with the air in the cylinder for combustion. At the endof the injection phase as fuel pressure drops, theneedle reseats to block the flow of fuel into thecylinder.
The bleed off (or leak off)line serves the samefunction as the internalbleed passages in the olderstyle unit injectors. Internalhigh pressure leakage
between components in thenozzle assembly is collectedand routed back to thereturn fuel system before it
Bleedoff
Highpressure
from
pump
INJECTOROPERATION
3.4
BLEED OR LEAKOFF LINE
3.5
-
8/10/2019 EMDEC troubleshooting tool
51/376
3
Notes:
-
8/10/2019 EMDEC troubleshooting tool
52/376
Notes:
-
8/10/2019 EMDEC troubleshooting tool
53/376
4
EMDEC ElectronicComponents &Operation
This section of the text will concentrate on theelectronic components that make up EMDEC, andhow the systems function to control injection. For thepurpose of instruction, a typical 16-cylinder 710engine application is used. 265H engine applicationsuse a similar control method.
The text will use a building block approach, discussingeach component in detail as it pertains to operation.The main electrical and electronic components of theEMDEC system are:
1. ECMs (Engine Control Modules): The actualinjection control computers.
2. Power Supply: 74 VDC to 24 VDC EMDECpower source.
3. Interface Module: Communication interfacebetween EMDEC and the main controlsystem.
4 S E i f
INTRODUCTION4.1
-
8/10/2019 EMDEC troubleshooting tool
54/376
-
8/10/2019 EMDEC troubleshooting tool
55/376
4
As stated before, the main components of the systemare the engine mounted ECM's. These units are self-contained microprocessors that operate on 24 VDC.Each ECM has the ability to control up to 8 injectors.
Therefore, the number of ECM's applied depends onthe engine configuration for example:
8-cylinder engine has one ECM.
12-cylinder engine has 2 ECM's (right bank 1
thru 6, left bank 7 thru 12).
16-cylinder engine has 2 ECM's (right bank 1thru 8, left bank 9 thru 16).
20-cylinder engine has 3 ECM's (right bank 3thru 10, left bank 13 thru 20, center (1,2,11,and 12).
ENGINE CONTROLMODULES (ECMS)
EM200074 VDC
ABCD
74 VDC
ABCD
FAULT DATA
TIMING & SPEED INFOSRS
TRS
RPM
24 VDC
Request24 VDC
POWER
SUPPLY
LOCO
INTERFACE
4.2
-
8/10/2019 EMDEC troubleshooting tool
56/376
Physically all ECMs are identical, but the software isdifferent for each unit. Every application has oneECM designated as a sender (or controlling) ECM.The software provides the units identity as well as the
application specific operating parameters (speedschedules for example). The sender is responsible forprimary data processing, and overall control of enginefunctions. The remaining ECMs carry the designationof receiver(s).
Receiver ECMs are controlled by the sender ECM,which provides basic information such as injectionpulse width (fuel amount), and base injection timing.Remember, the number of receiver ECMs dependson the number of engine cylinders. The softwareallows for some independent operation of the unit, and
engine RPM requests and basic timing feedbacks arefed to the receiver(s), independent of the sender. Thiswill allow the system to overcome intermittentcommunication problems between the sender andreceiver(s).
The location of the ECMs on the engine will varydepending on application.
Early 16-cylinder 710 models have the ECMs
Arrangement4.2.1
-
8/10/2019 EMDEC troubleshooting tool
57/376
-
8/10/2019 EMDEC troubleshooting tool
58/376
In previous models, the Power Supply (figure 4.3)onthe following page is located in the AC Cabinettowards the rear of the locomotive. Later models havethe power supply located in the electrical locker nearthe door.The function of the power supply is to stepdown and filter the 74 VDC control system voltage to24 VDC. EMDEC was originally designed for heavytruck type applications, therefore operates on a systemvoltage of 24 VDC. The output of the power supply isfed directly to the interface module, and through a
power harness, to the engine mounted ECMs.
In applications other than locomotive, control systemvoltage will be filtered and regulated to provide astable 24 VDC supply. While the appearance of thepower supply will be different, the function remains
the same.
The Power supply is fed through the engine controlcircuit breaker located on the fuse and circuit breakerpanel. Note that both the positive and negative sides ofthe circuit are protected. The power supply is
equipped with two LEDs (light emitting diodes) on itsface to indicate status.
The green LED (normally on) indicates that the
POWER SUPPLY
4.3
-
8/10/2019 EMDEC troubleshooting tool
59/376
4
EM200074 VDC
ABCD
74 VDC
ABCD
FAULT DATA
TIMING & SPEED INFO
FEEDBACKS
INJECTORS
9-16
INJECTORS
ECM
RECEIVER
ECM
SENDER
F P
F T
SRS
TRS
RPM
24 VDC
Request
AP
O P
O T
24 VDC
POWERSUPPLY
LOCOINTERFACE
-
8/10/2019 EMDEC troubleshooting tool
60/376
INTERFACEMODULE
In previous models, the Interface Module is located inthe AC cabinet of the locomotive, and is typicallymounted on the side of the power supply. Latermodels have the interface module located in theelectrical locker. The function of the module is totranslate signals being sent from the control system toEMDEC, and data traveling from EMDEC back tothe control system.
Engine speed information is communicated from the
control system to the ECMs through an interfaceboard.
Depending on the application, the connection fromthe interface module to the control system may be aone-way or two-way serial data link.
The main difference between the two types of links isin the amount of data that can be transmitted. Theone-way link allows for simple speed instructions fromthe EM2000 to EMDEC, and simple fault messagesand performance feedbacks from EMDEC to the
EM2000. The two-way serial link allows for enhanceddata transmission both ways.
4.4
-
8/10/2019 EMDEC troubleshooting tool
61/376
4
With the one-way serial link, the ECMs areprogrammed to accept 4 input signals, which are thentranslated into set speeds. Throttle information is sentfrom the control system to the interface module as 0 or74 VDC governor solenoid signals. The interfacemodule translates these 0 or 74 VDC signals intoinverse logic 0 or 24 VDC signals for the ECM's.Consider the following examples:
Example #1 - Throttle in Normal Idle(300 RPM)
Control System Signals Interface Signals
ECM Set Speed
A Valve - 0 VDC A Valve - 24 VDC
B Valve - 0 VDC B Valve - 24 VDCC Valve - 0 VDC C Valve - 24 VDCD Valve - 0 VDC D Valve - 24 VDC
Example #2- Throttle in Run 6(730 RPM)
Control System Signals Interface Signals
ECM Set Speed
A Valve - 74 VDC A Valve - 0 VDCB Valve - 74 VDC B Valve - 0 VDCC Valve - 74 VDC C Valve - 0 VDCD Valve - 74 VDC D Valve - 0 VDC
Speed Control -
One-Way SerialLink (LocomotiveApplication)
SPEED CONTROL
4.5
4.5.1
-
8/10/2019 EMDEC troubleshooting tool
62/376
The two-way serial link functions much differently forengine speed control. Instead of speed signals sent toEMDEC as governor solenoid signals (signals are stillgenerated for trainline control), EM2000 creates exactRPM requests (for example 1000 RPM), and relaysthese to the ECMs over the serial link. This method isvery fast and decreases the chance of problems in thespeed signals. Note that the two-way serial link passesall communication through the interface panel.
Fault data and load control information are sent backto the control system from EMDEC through theinterface module. These types of data will be looked atin greater detail in later chapters.
In a marine application, control signals are relayed tothe ECMs as a variable speed governor signal. Notethat the signal is supplied to the ECMs as Vref(ECM#ID). As the original voltage is increased, theECMs will translate the reference signal to an RPMrequest.
Power generation applications typically use twoseparate engine speeds only; IDLE (standby) and
Speed Control -Two-Way SerialLink (LocomotiveApplication)
4.5.2
Speed Control -(MarineApplication)
4.5.3
Speed Control
4.5.4
-
8/10/2019 EMDEC troubleshooting tool
63/376
4EM2000
74 VDC
ABCD
2 WAY
SERIALLINK
ABCD
TIMING & SPEED INFO
FEEDBACKSINJECTORS
9-16
ECM
SENDER
F
P
F T
SRS
TRS
RPM
24 VDC
Request
O P
24 VDCPOWERSUPPLY
LOCOINTERFACE FAULT &
SENSORDATA
-
8/10/2019 EMDEC troubleshooting tool
64/376
EM200074 VDC
ABCD
74 VDC
ABCD
FAULT DATA
TIMING & SPEED INFO
FEEDBACKS
INJECTORS
9-16
INJECTORS
1-8
ECM
RECEIVER
ECM
SENDER
F
P
F T
SRS
TRS
RPM
24 VDC
Request
A P
A T
O P
O T
C P
CC
24 VDC
POWER
SUPPLY
LOCO
INTERFACE
-
8/10/2019 EMDEC troubleshooting tool
65/376
4
At this point, the system has been supplied with 24VDC for operation, and has received speed inputsfrom the control system. Before EMDEC can operatethe injectors, additional information is required suchas timing and speed data, engine performance data,
and engine protection data. All this information comesinto the ECMs in the form of sensor inputs. Thesensors can be broken down into three major groups:
1. System Sensors for timing and speedinformation:
Synchronous Reference Sensor (SRS) Timing Reference Sensor (TRS)
2. Performance Sensors for calculating fuel injectoroperation:
Fuel Pressure Sensor (FPS) Fuel Temperature Sensor (FTS) Turbo Boost or Air Pressure Sensor (TBS) Air Temperature Sensor (ATS)
3. Protective Sensors for monitoring ofsupport systems:
Oil Temperature Sensor (OTS)Oil P S (OPS)
SENSORS
4.6
-
8/10/2019 EMDEC troubleshooting tool
66/376
System Sensors
The system sensors (figure 4.6a and 4.6b)provide twofunctions for EMDEC operation. Timinginformationis used by the ECM's to determine when to energizethe injector solenoids. Speedinformation is used tocompare actual engine speed to desired engine speed.Fuel rates are then adjusted by the ECM's to correct anyvariation. Unlike other sensors on the engine, the systemsensors (SRS & TRS) are magnetic pickups. Operation ofthe system sensors is identical between the 710 and Hseries engines, however the mounting arrangement is
very different.
4.6.1
Figure 4.6a 710 Series System Sensors, Previous Models (Left) Recent Models (Right).
-
8/10/2019 EMDEC troubleshooting tool
67/376
4
The early 710 series of engines have three timingplates (figure 4.7a)attached to the inside face of thecoupling disk between the engine and ring gear. Theplates have openings cut into them leaving 36 spokesthat are used to generate signals by the TRS sensor.One of the plates has a (Position Indicator Pointer) PIPattached, that is used by the SRS sensor to generatesignals.
SRS and TRS share a common mounting bracket
located on the left rear corner of the engine. Thisbracket serves two functions; first to hold SRS and TRSin precise alignment with the PIP and spokes on thetiming plates; and second, the spring and stopmechanism allows the bracket to swing back and thenreturn to the original position should the coupling disk
flex. This serves to protect the sensors from damagecaused by contact with the timing plates.
System SensorMountingArrangements -Early 710 Series
4.6.1.1
-
8/10/2019 EMDEC troubleshooting tool
68/376
An improved feature on the 16-710G3C-T2 engine isthe mounting and accessability of the SRS and TRSsensors.
Figure 4.7b SRS and TRS Sensors.
The H series of engines does not use coupling disk
mounted timing plates like the 710. Instead, theseengines have timing disks attached to the front andrear of the camshaft (figure 4.7c). The timing diskshave a circle of 36 raised bumps stamped into them,that are used to generate signals by the TRS sensor.Each disk also has a stamped PIP that is used by theSRS sensor to generate signals. Note that although
there is a disk on each end of the camshaft, only therear plate is used at this time.
System SensorMountingArrangements -H Series
4.6.1.3
Setting SRSand TRS Sensors
4.6.1.2
-
8/10/2019 EMDEC troubleshooting tool
69/376
4
Timing
Synchronous
ReferenceSensor
SRS and TRS are rigidly mounted in the coverhousing the rear camshaft gear. They are arranged toread the stamped protrusions on the timing disk andrelay this information to the ECM's. Reading camshaftspeed (one half crank speed) allows for the use of thesame ECM's as the 710 series.
The Synchronous Reference Sensor or SRS provides asignal to the ECMs when the Position Indicator
Pointer (PIP) passes in front of it. The action of the PIPpassing in front of the pick-up causes a small current tobe induced in the sensor, which then passes throughthe wiring harness to the ECMs. This signal isprovided once, for every revolution of the crankshaft,and indicates when the number one cylinder is four
degrees before top dead center.
This signal synchronizes the ECMs with respect toengine speed and crankshaft position, this tells theECMs when to start the timing count.
The Timing Reference Sensor or TRS reads the metalspokes of the timing plates. As the engine rotates, the
4.6.1.4
4.6.1.5
-
8/10/2019 EMDEC troubleshooting tool
70/376
PerformanceSensors
Note that unlike other systems, there are no specifictiming indicators for each cylinder. Instead, the firingorder of the engine is contained in the ECMssoftware. With this type of a system, the same pick-ups,timing plates, and wiring harness may be used with anyengine configuration.
The calculation of engine speed is quite simple. TheECMs simply look at the elapsed time between TRSpulses to calculate engine speed. This is thencompared to the set speed. If actual speed is lower than
set speed, EMDEC will lengthen the injector pulsewidth to add fuel to the engine. If actual speed ishigher than set speed, EMDEC will shorten the pulsesto reduce the amount of fuel injected.
The performance sensors (figure 4.8)provideinformation that is used for adjustment of fuel rates. By
NOTE:
The sensors used as examples in this section are for a
generic 16 cylinder 710 series engine. The feedbacks
portrayed are to be used as examples only as there are
several different models of sensors used in service
depending on specific application. Note also that the
number of sensors used will vary.
4.6.2
-
8/10/2019 EMDEC troubleshooting tool
71/376
4
EM200074 VDC
ABCD
74 VDC
ABCD
FAULT DATA
TIMING & SPEED INFO
FEEDBACKS
INJECTORS9-16
INJECTORS
1-8
ECM
RECEIVER
ECM
SENDER
F P
F T
SRS
TRS
RPM
24 VDC
Request
A P
A T
O P
O T
C P
C C
P
24 VDCPOWERSUPPLY
LOCO
INTERFACE
PERFORMANCE
SENSORS
Figure 4.8 Performance Sensors.
-
8/10/2019 EMDEC troubleshooting tool
72/376
The Turbo Boost or Air Box Pressure Sensor (figure4.9)provides data to the sender ECM for use primarilyin emission control. It is also known as the smokesensor. The sensor is connected to the ECM with athree wire plug, and to the engine with a sensing hose
off the left front corner of the engine. The device ismounted just below the crankcase pressure sensor,(early 710 systems), in the sensor box (late 710systems), or on the front of the aftercooler ducts (HEngines).
Figure 4.9 Turbo Boost Sensor.
Turbo BoostSensor (TBS)
4.6.2.1
-
8/10/2019 EMDEC troubleshooting tool
73/376
4
Figure 4.10 shows a typical feedback graph. Note thatthe device measures absolute pressure and at 0 psi, thefeedback voltage is approximately 0.5 VDC. Note alsothat at 45 psi, the feedback is approximately 4.5 VDC.The ECM looks at this feedback signal for threeconditions.
Boost Pressure SensorP/N 16070629
6
5
4
3
2
1
010 15 20 25 30 35 40 45
SensorO
utput(Volts)
Airbox Pressure (psi)
Check calibration at25 C and Vin = 5.1 VDC
Normal
Error Limits
-
8/10/2019 EMDEC troubleshooting tool
74/376
In either case, the following happens:
the feedback is ignored for calculations,
a nominal "standard" pressure is used,
a "fault" is generated in the archives specific tothe feedback failure (voltage low or high).
Remember that the fault archive can be accessed byuse of a laptop computer (with WinEMMON or PCReader software), or the FIRE display (two-way serial
link).
The Air Temperature Sensor or ATS (figure 4.11)measures the temperature of the air charge in theengine airbox. This feedback is necessary for fuelconsumption calculations and emission control by theECMs. The sensor is applied to the left front corner ofthe engine next to the turbo boost sensor, with theprobe inside the airbox. On some applications, asecond sensor, inlet air temperature (IATS) has been
applied to the inlet eye of the turbocharger. Thissecond sensor is identical to the Air Temperaturesensor.
Air Temperature
Sensor
4.6.2.2
-
8/10/2019 EMDEC troubleshooting tool
75/376
4
This sensor is a thermistor type device. As thetemperature changes at the sensor probe, the internalresistance of the device changes. The voltage andcurrent characteristics of the circuit are looked at bythe ECM, and are converted into a temperature
reading.
Temperature Sensor ResistanceP/N 40063567
100,000
10,000
1,000
100
10
0 50 100 150 200 250 300
SensorOu
tput(ohms)
( )
Calibration points:
77 F = > 2590.7-2964.7 ohms
262.4 F = > 77.7-84.9 ohms
-
8/10/2019 EMDEC troubleshooting tool
76/376
FuelTemperatureSensor
The Fuel Temperature Sensor or FTS (figure 4.13)measures fuel supply temperatures necessary for fuelconsumption calculations, and fuel inputcompensation by the ECMs. This is one of thefunctions that goes beyond the possibilities of the
mechanical system. The fuel temperature sensor is anidentical device to the air temperature sensor(s). It islocated on the secondary fuel filter manifold andexamines the temperature of the fuel as it enters theengine. As fuel temperature increases, performancedecreases. EMDEC will compensate for high fueltemperatures by adjusting pulse width and timing asrequired.
Figure 4.13 Fuel Temperature Sensor.
4.6.2.3
-
8/10/2019 EMDEC troubleshooting tool
77/376
4
The Fuel Pressure Sensor or FPS (figure 4.14)monitors fuel supply pressure for two reasons. First, thefuel pressure reading is an input to the sender ECMwhere it forms part of the fuel rate calculations.Second, should fuel pressure drop below an
acceptable level, the system will log a fault to warn ofany impending power loss.
Figure 4.14 Fuel Pressure Sensor.
The device is a capacitive pressure transducer.Operation is quite similar to that of the boost pressure
FuelPressureSensor
4.6.2.4
-
8/10/2019 EMDEC troubleshooting tool
78/376
Figure 4.15 Fuel Pressure Sensor.
Figure 4.15 shows a graph of the sensor output. Note
that the cut off points for feedback voltage areapproximately 0.5 VDC and 4.5 VDC. If the feedbackis maintained within this range, the ECM will
id h i l lid d h f db k f
Pressure Sensor SignalP/N 40059731 or 40087573
5
4
3
2
1
0
0 20 40 60 10080 120 140 160 180 200
SensorOutput(Volts)
Pressure (psia)
Normal
Error Limits
Check calibrationbetween 77 and 221 F
at 5.0 .1VDC
-
8/10/2019 EMDEC troubleshooting tool
79/376
4
The protective sensors (figure 4.16)provideinformation that is used by the sender ECM to
monitor the performance of the engine supportsystems. In the event of a system failure (lube oil,cooling, or crankcase ventilation), EMDEC can shutdown the engine to prevent costly component damage.The protective functions of EMDEC have beenprogrammed to react in exactly the same manner as a
Woodward governor. All shutdown pressures,temperatures, and timing remain the same as on themechanical system.
PROTECTIVESENSORS
NOTE:
The sensors used as examples in this section are for a
generic 16 cylinder 710 series engine. The feedbacks
portrayed are to be used as examples only as there are
several different models of sensors used in service
depending on specific application. Note also that the
number of sensors used will also vary.
4.6.3
-
8/10/2019 EMDEC troubleshooting tool
80/376
EM200074 VDC
ABCD
74 VDC
ABCD
FAULT DATA
TIMING & SPEED INFO
FEEDBACKS
INJECTORS
9-16
INJECTORS
1-8
ECMRECEIVER
ECM
SENDER
F P
F T
SRS
TRS
RPM
24 VDC
Request
A P
A T
O P
O
T
C P
C
C P
24 VDC
POWER
SUPPLY
LOCOINTERFACE
PROTECTIVE
SENSORS
-
8/10/2019 EMDEC troubleshooting tool
81/376
4
Oil PressureSensor
The Oil Pressure Sensor or OPS (figure 4.17)providesa feedback of engine lube oil pressure to the ECM. Ashutdown will occur if the engine lube oil pressure atthe turbocharger drops below a predeterminedsetpoint, relative to engine speed and duration of time.
The oil pressure sensor is an identical unit to the fuelpressure sensors, and is mounted in the top of theturbo lube filter head or on the left front corner of theengine in some applications.The shutdown times andpressures are identical to previous systems.
Figure 4.17 Oil Pressure Sensor.
4.6.3.1
-
8/10/2019 EMDEC troubleshooting tool
82/376
Oil TemperatureSensor
Physically, the Oil Temperature Sensor or OTS (figure4.18)is identical to the fuel and air temperaturesensors. The input to the sender ECM allows it tomonitor the temperature of the oil entering the lube oilsystems in the engine. An engine shut down will occur
if the oil temperature exceeds 256F (124C). Thesensor is located in the same position as the hot oildetector on the mechanical injection system.
Figure 4.18 Oil Temperature Sensor.
This sensor also has three possible types of faultconditions. Input voltage high or input voltage low willeach generate a separate fault condition. If the signalfrom the sensor is valid (between 0.5 and 4.5 VDC), but
above the operating parameters, a shutdown fault islogged and fuel injection is cut off, stopping theengine. This will prevent damage to enginecomponents caused by excessive oil temperatures.
4.6.3.2
-
8/10/2019 EMDEC troubleshooting tool
83/376
4
CoolantPressureSensors
The Coolant Pressure Sensors or CPS , monitorcoolant pressure at the water pump discharges, and atthe Y pipe (engine discharge). The sender ECM maybe connected to one, two, or three CPS depending onsystem requirements and engine configuration. A
typical system will use two sensors. The coolantpressure sensors (figure 4.19)are identical units to theoil and fuel pressure sensors. If coolant pressure dropsbelow a programmed set point, an engine shut downwill be initiated.
Figure 4.19 Coolant Pressure Sensor.
4.6.3.3
-
8/10/2019 EMDEC troubleshooting tool
84/376
CrankcasePressureDetector (CCP)
The Crankcase Pressure Detector (figure 4.20)activates if crankcase pressure increases to a positivepressure of 1 1/2" of water.Unlike other sensors, theCCP is a mechanical
device. The detectorconsists of a sensingdiaphragm, trip button,and electrical switch. It islocated in the samelocation as the EPD onmechanical injectionsystems.
Following a crankcase pressure shutdown do not openi f i i f t h A
Figure 4.20 Crankcase Pressure
Detector.
DO NOT attempt to restart the engine until the cause of
the shutdown has been determined and corrected.
WARNING:
4.6.3.4
-
8/10/2019 EMDEC troubleshooting tool
85/376
4
The mechanical portion of the device must bequalified on maintenance inspections to ensure properoperation. Consult section 13 of the EMM for testprocedures.
The crankcase pressure sensor has been developed toreplace the crankcase pressure detector. It is located inthe sensor box on the left front corner of the engine(figure 4.20). Unlike other pressure sensors this devicecan read both positive and negative pressures. Engine
protection parameters and responses remain the sameas the CCP.
This completes the section on electronic componentsof the EMDEC system. The following chapters willdeal with load control, fault data, troubleshooting, anddiagnostic tools.
CrankcasePressureSensor
4.6.3.5
-
8/10/2019 EMDEC troubleshooting tool
86/376
Notes:
Load
-
8/10/2019 EMDEC troubleshooting tool
87/376
5
The term load control refers to the matching ofelectrical load on the main generator to engineperformance. In one way, this may be considered as
another protective system for the diesel engine. If thereis a problem with the engine that will reduce availablehorsepower, such as plugged air or fuel filters, it isnecessary to reduce the load on the engine to preventdamage to components or over-fueling. Over-fuelingleads to unacceptable levels of exhaust emissions andpossible engine damage.
Control of the actual load on the generator, commonlyreferred to as excitation level, is the responsibility ofthe locomotive control system. The injection system
must provide the control system with a feedback thatwill indicate the engines ability to maintain speed atthe given load level.
This section of the text will look at this feedback, howit is generated, and how it is used by the control system
to modify the load.
Load control with EMDEC protects the dieselengine against overloading and overfueling
Control
INTRODUCTION
5.1
-
8/10/2019 EMDEC troubleshooting tool
88/376
The operator establishes a desired power level usingthe control system (figure 5.1). The control systemdetermines excitation levels and engine speeds. Thecontrol system speed relays commands to EMDEC,EMDEC, through the interface module.
Once the ECMs receive the signal from the interfacemodule, this is converted to a set speed. As we saw inthe previous chapter, the ECMs will control the fuelinjectors based on sensor inputs, to maintain actualengine speed at the set speed level.
SET
SPEED
SET
SPEED
CONTROL CONSOLE EM2000
COMMUNICATIONS
PORT
THROTTLEHANDLE
THD1 THRU 8
INTERFACE MODULE
EMDEC HASITS OWN
ISOLATEDGROUND
24V SYSTEM
LOAD OUTPUTDIGITAL SIGNAL
(ONE WAYSERIAL LINK)
EMDECSENDING MASTERECM (SENDER)
SERIAL LINKFUEL PULSE WIDTH TO EUI INJECTORS
-
8/10/2019 EMDEC troubleshooting tool
89/376
5
FUEL MAPS
5.2 Fuel maps are programmed into the ECMs software(figure 5.2), that indicate allowable pulse widths foreach throttle position. Remember that the injectorpulse widths refer to the duration of the injectionpulse, measured in degrees of crankshaft rotation. The
longer the pulse width, the more fuel is injected intothe engines cylinders.
As we see in the below, there is a different map foreach throttle position. These are examples only;actual maps vary according to application. For
example, in throttle 5, an allowable pulse width forinjection would be anything from 0to 15. In throttle8, any pulse width between 0and 23may be used bythe ECMs. The fuel maps indicate the total availablefuel for each throttle position.
2
IDLE OR 1
Throttle
Position
3
4
-
8/10/2019 EMDEC troubleshooting tool
90/376
CONTROLLING
ENGINE SPEED
5.3 EMDEC works just like a Woodward governor tocontrol engine speed. If speed drops, it adds fuel(opens the injector pulse widths). If speed rises, it cutsfuel (closes the injector pulse widths). A feedback tothe control system is still required to prevent overfueling.
EMDEC will generate a reference signal proportionalto the amount of fuel being consumed (figure 5.3).
In the above illustration, we see examples of the fuel
maps for throttle 5 and throttle 8. As EMDEC operatesthe injectors, it generates the Engine Ratio signal. Thisis the actual pulse width divided by the maximumpulse width expressed as a percentage Simply put the
Throttle
Position
PULSE WIDTH
(Degrees of Crankshaft Rotation)
PULSE WIDTH
(Pulse Width Degrees...)
5
8
0 11.5 21.5 23
15117.5
100%87%50%0%
100%50% 87%
0
Figure 5.3 Engine Ratio Signal.
-
8/10/2019 EMDEC troubleshooting tool
91/376
5
Normally, if everything is operating properly underload conditions, the engine will require approximately78% to 80% of the total available fuel. Actualconsumption will vary according to engine and ambientconditions. For example, in Load Test 1, the engine
typically will use a pulse width of about 18.5inthrottle 8. This would equate to an engine ratio signalof approximately 80%; it is consuming 80% of the totalavailable fuel in throttle 8. Should there be any problemswith the engine, for example plugged air filters,performance will drop, and EMDEC will have to addmore fuel to the engine to maintain speed against theload on the generator. As the pulse width is openedby the ECMs, the Engine Ratio signal increasesproportionally.
The Engine Ratio signal is sent to the EM2000 via theinterface module, and the serial data link. By lookingat this signal, the EM2000 can assess the enginesability to make horsepower. As long as the EngineRatio is less than 87%, the EM2000 will assume thatthe engine can make full power, and will regulate
generator excitation to produce the proper kilowattoutput for the throttle position.
However should the Engine Ratio rise to 87% for any
-
8/10/2019 EMDEC troubleshooting tool
92/376
Notes:
-
8/10/2019 EMDEC troubleshooting tool
93/376
5
Notes:
-
8/10/2019 EMDEC troubleshooting tool
94/376
DiagnosticTools
-
8/10/2019 EMDEC troubleshooting tool
95/376
6
DiagnosticTools
INTRODUCTION
6.1 This section of the text covers the use of diagnostictools to access the EMDEC ECMs. These tools arerequired for troubleshooting, loading software, and
injector calibration. Covered, are procedures for usingthe WinEMMON or PC Reader program with alaptop computer and the FIRE display for applicationsequipped with a two-way serial link.
Note that EMDEC is an evolving system that isconstantly being upgraded to improve servicereliability and performance. Every effort has been hasbeen made to ensure that the information containedin this section is current, however, always consult theproper system schematics and EMM for specific
service data.
The WinEMMON kit (figure 6 1) is the recommended6 2
-
8/10/2019 EMDEC troubleshooting tool
96/376
The WinEMMON kit (figure 6.1) is the recommendedEMDEC interface tool. Some locations will have theolder PC Reader system as a diagnostic tool, so this willbe covered as well. The primary difference between thetwo system diagnostic tools is that WinEMMON is a
Windows based system while PC Reader is based onthe older DOS (Digital Operating System) technology.
The following instructions are provided to assist thetroubleshooter in using this tool. The PC reader enablesyou to:
monitor all sensor inputs to the ECMs;
view ECM outputs to the injectors (pulse width and timing);
view injector response times;
calibrate the injectors;
load ECM software;
view and download fault data.
The software generates a diagnostic screen and interface
protocol on the laptop. To use the program, it must beloaded into the laptop, the laptop connected to theEMDEC system through the cable and translator
bl d h d h f ll
WINEMMON &PC READER(DIAGNOSTICSWITH A LAPTOP
PC)
6.2
WinEMMON and PC Reader are software programs6 2 1
-
8/10/2019 EMDEC troubleshooting tool
97/376
6
WinEMMON and PC Reader are software programsthat are run on a personal computer interfaced withthe EMDEC system. It is recommended that
WinEMMON be used in a laptop PC running aWindows 95 operating system or newer, such as
Windows 98, 2000, NT, XP, or XP PRO. You willalso need the WinEMMON Diagnostic Kit(#40094241), which consists of the following:
WinEMMON Translator Box #40094242
WinEMMON Software Disk #40094243 15 D-R Plut #40055365
PCT-R Cable #40055364
9 Pin Male to 9 Pin Female Cable #40055366
PC Carry Case #40055367
The minimum requirement for using PC Reader is a386SX/DX-type laptop with one megabyte of RAM.In addition, the PC Reader kit (#40055368),
consisting of the following items, is required:
EMDEC Translator Box #40055363
Using theWinEMMON orthe PC Reader Kit
6.2.1
6.2.2 1 Insert disk #1 of the WinEMMON
-
8/10/2019 EMDEC troubleshooting tool
98/376
LoadingWinEMMONSoftware On To ALaptop Computer
6.2.2 1. Insert disk #1 of the WinEMMONsoftware (#40094243) into the floppy diskdrive of your laptop computer (usuallythe A: drive).
2. Click on the Start button in the lower leftcorner of your computer screen.
3. When Run appears above the Startbutton, click on Run.
4. When the command box opens, type inA: setup, without the quotations marks,then put the mouse on OK and click it.
5. The computer will then copy theinitialization files required from disk #1.
When that is done, the computer will tellyou to insert disc #2.
6. Remove disk #1 from the floppy driveand insert disk #2, then click on the ok
button.
7. This will allow the setup program toproceed Close any other programs you
8. Next you will be asked where you would
-
8/10/2019 EMDEC troubleshooting tool
99/376
6
8. Next you will be asked where you wouldlike the WinEMMON directory to beplaced on your computer. The defaultlocations is Program Files on the C:drive. If you wish to put your WinEMMON
program somewhere else on your computerthan the default choice (not recommended),click on the Change Directory button andfollow the instructions that appear. If you aregoing to use the default location (recommended),then click on the large box in the upper left of the
pop up box (it has a computer icon on it).
9. The computer will now copy the WinEMMONfiles to the chosen directory. When the computertells you that the installation has beensuccessfully completed, click on the OK button.
You have now successfully installed WinEMMON onyour computer. Connection and diagnostics use willbe covered later in this chaper.
1. Escape out of Windows and get to the C:\>6.2.3
-
8/10/2019 EMDEC troubleshooting tool
100/376
p t g t t tprompt. It is imperative that windows not beactive, or the program will not function as desired.Press Alt+F4 or double click the cursor on theupper left bar on the windows screen to exit
Windows.
2. Create a new directory (For example:C:\> md emdec).
3. Change the directory to the pcreader
(For example: C:\> cd emdec).
4. Once in the directory, copy the files fromthe disk into the directory (For example:C:\emdec> copy a:\*.* ).
Occasionally the PC Reader software is upgraded toenhance its operation, or to reflect changes in theequipment installed on the engine. After receiving anew version of PC Reader, it will be necessary tochange the files in the laptop. To ensure properoperation, use the most recent software.
Loading The PCReader SoftwareOn To A LaptopComputer
1. While in the EMDEC directory, type in:6.2.3.1
-
8/10/2019 EMDEC troubleshooting tool
101/376
6
y, ypedit emmon.bat. A screen will appearshowing the contents of the emmon file.
Example: @ECHO OFF
rp1202emmon11a (or currentversion number)ECHO ON
2. Use the cursor to select the existing
executable file (For example emmon11aor current version number), and renameit to the latest executable file nameloaded (such as emmon11a).
3. Press Alt + F to highlight the File task
bar, and open the dialog box.
Select SAVE and press .
4. Press Alt + F to highlight the File taskbar and open the dialog box once again.
Select EXIT to return to theemdec directory.
To Edit TheEMMONCommand File
On most applications there are two access locations for6.2.3.3
-
8/10/2019 EMDEC troubleshooting tool
102/376
EMDEC (figure 6.2).
One is located in the cab of the locomotive, inside thecenter door of the Computer Chassis Cabinet. The
EMDEC access port is located to the right of theEM2000 computer chassis, and is labeled EMDEC.
The second access port is located on the interfacemodule mounted to the 24 VDC power supply. It isusually found in the AC Cabinet in the EngineCompartment.
Access Ports
80 SERIES / 90 SERIES
AC CabinetHigh Voltage CabinetEMDEC Ports
-
8/10/2019 EMDEC troubleshooting tool
103/376
6
ElectricalLocker
Figure 6.3 EMDEC Access Port (SD70ACe/ SD70M-2).
1. Connect the 9 Pin cable from the PC to6.2.4
-
8/10/2019 EMDEC troubleshooting tool
104/376
the translator box.
2. Connect the 15D-R plug to the PCT-Rcable, and the other end of the cable tothe translator box.
3. Connect the 15D-R plug into the EMDECreader port, and note that both the red and greenLEDs on the side of the translator box areilluminated.
The EMDEC Communications (EMMON)program will not work if the hardware is notconnected to the locomotive.
4. Click on the Start button in the lower leftcorner of the computer screen. When the menu
options appear, click on all Programs/Programs(depending on which version of Windows youare using). Move the cursor (arrow) to the
WinEMMON option, and click there. ForPC Reader change the directory on the PC toC:\emdec> and type EMMON to startthe program.
A message will appear stating that the program is
UtilizingWinEMMON &The PC ReaderProgram
-
8/10/2019 EMDEC troubleshooting tool
105/376
6If the software is loaded correctly, and the system isproperly connected, a main screen should appear onthe laptop (figure 6.4).
The systems (EMDEC, WinEMMON or PC Reader),
are communicating when the green light on thetranslator box is illuminated, and the red light isflashing. If there is a problem with the connection,another message box will appear (figure 6 5) This
Figure 6.4 Communication Problem.
-
8/10/2019 EMDEC troubleshooting tool
106/376
Figure 6.5 Communication Problem.
The main WinEMMON screen consists of fivesections, covering Sender ECM, Receiver 1 ECM, and
Receiver 2 ECM. As well, there are sections forTranslator Box and System Description. In the lowerright corner of the Main Screen is a refresh button.The ECM sections give you the software part number
WinEMMON
Main Screen
6.2.5
-
8/10/2019 EMDEC troubleshooting tool
107/376
6Figure 6.6 WinEMMON Main Screen.
-
8/10/2019 EMDEC troubleshooting tool
108/376
Figure 6.7 System Information Dialog Box.
The WINEMMON main screen appears wheneveryou open the WinEMMON program, regardless ifyou are connected to the locomotive. The SystemInformation Dialog Box (see Figure 6.7)will thenappear on the computer screen This will document
-
8/10/2019 EMDEC troubleshooting tool
109/376
6Figure 6.8 System Information Dialog Box.If the connection is successful the System InformationDialog Box will show the connection data (see Figure
6.8).
-
8/10/2019 EMDEC troubleshooting tool
110/376
-
8/10/2019 EMDEC troubleshooting tool
111/376
6
Figure 6.10 Windows Translator Box Help Screen.
This Communication Error box will give you threeoptions, Retry, Cancel, and Help. Retry tells the systemto attempt to communicate with the locomotive again.Cancel will stop the whole process and close the
WinEMMON program. Help is a shortcut to theWinEMMON Help program, in particular the sectionon Translator Box connections, that gives a diagram ofthe proper connections and a description of same (see
-
8/10/2019 EMDEC troubleshooting tool
112/376
Figure 6.11 WinEMMON Main Screen (System Information)
This Help screen describes the two lights on theTranslator Box and gives some helpful suggestions tocorrect any connection problems you may encounter.
If the connection was successful, the WinEMMONMain screen will appear (see Figure 6.11). Across thet f th th ti l ti b tt
-
8/10/2019 EMDEC troubleshooting tool
113/376
6Figure 6.12 WinEMMON Main Screen (System Information).
On the left of the System Information Screen there are
three sets of ECM information fields. The sets of dataare labeled, from top to bottom:
S d ECM
ECM Data
6.2.5.1
The information in these fields shows:
-
8/10/2019 EMDEC troubleshooting tool
114/376
The software part number The software revision number The calibration name revision
This will be useful data when determining if thesoftware loaded into the ECMs is correct for theapplication. The data in these fields serves one otheruseful function; having the data in the fields serves toconfirm that the ECMs are communicating correctly
with WinEMMON.
On the right hand side of the screen are three otherdata fields. The two in the upper right hand corner ofthe screen are for the Translator box. These fields
show:
Status of the Translator Box (connectedor disconnected)
Version of the Translator Box being used
This data will help to trouble shoot a connectionproblem to determine if the fault lies within the physical
Secondary Data
6.2.5.2
The field in the lower right hand side of the screen isfor system information, that is which engine/wiring
-
8/10/2019 EMDEC troubleshooting tool
115/376
6
y g gcombination is used on that particular engine. Belowthat is the Refresh button, which will replace the datawith fresh data whenever clicked on.
If you move the computer cursor (usually an arrow) tothe top of the screen and on to the Monitor button,then click on it (on the keyboard of the computer,usually close to the mechanism for moving the cursor,will be two buttons. The left of these buttons will
usually be the selector button that you press, or click,to make your selection. The mechanism for movingthe cursor will usually be a small pad that you dragyour finger across, known as a touch pad, or a smallbutton called a pointer) the Monitor screen willappear, see Figure 6.13.
-
8/10/2019 EMDEC troubleshooting tool
116/376
Figure 6.13 Monitor Screen.
The Monitor screen allows the operator to look at, ormonitor, engine functions in real time. All sensorfeedbacks monitored by EMDEC can be monitored.These include engine speed, engine RPM set point,engine R (as shown), as well as such things as temperaturesand pressures. The signals (known as parameters) shown in
Figure 6.13 are the default signals that are loaded whenyou first open the monitor screen. Other parameters canbe selected by moving the cursor to the Select Parametersb tt i th l i ht h d id f th d
Monitor Screen
6.2.5.3
Once the desired parameters have been selected, move thecursor to the Save button and click on it if those parametersselected are the parameters the operator wishes to keep
-
8/10/2019 EMDEC troubleshooting tool
117/376
6
selected are the parameters the operator wishes to keepusing. Note that the parameters can be changed at anytime, as required.
There are two signals that are extremely valuable fortroubleshooting. The first one is Engine Ratio, that wasdiscussed in the Load Control Section. It is the bottomline of the box and is labeled as "% max fuel".The second signal is labeled "% allowable torque".
If EMDEC is satisfied with the performance sensorinputs (fuel temp, fuel pressure, air temp, and airpressure),it will maintain this signal at 100%.
If EMDEC itself must cut back on horsepowerbecause of an engine performance problem (such as
low boost pressure), this signal will be reduced.
Reducing the allowable torque signal has the effect oflowering the top ends of the fuel maps. This in essencewill increase the Engine_R signal to the EM2000,causing it to reduce generator excitation.
Remember the three signals.
-
8/10/2019 EMDEC troubleshooting tool
118/376
Figure 6.14
Data Save Box.
A Snapshot of data can be taken and saved by movingthe cursor to the Save button and clicking on it. ASave box then opens (see Figure 6.14), requiring theoperator to name the data file (unit number, date, or
other relevant information that identifies the datashould be used) and then move the cursor to theOpen button and click on it. A second Save box
Saving Data
6.2.5.4
-
8/10/2019 EMDEC troubleshooting tool
119/376
6
Figure 6.15 Diagnostics Screen.
If the operator then moves the cursor to the top of theMonitor screen and places it on the Diagnosticsbutton, and clicks on it, the Monitor screen will closeand the Diagnostics screen will appear (see Figure6.15).
The Diagnostics screen is a Real time display ofcurrent faults both active and inactive from the
Diagnostics
6.2.6
For example, in Figure 6.15, the Diagnostics screenshows us that there are no Active Faults. UnderInactive Faults Proprietary Data Link is displayed
UnderstandingThe Fa lt Screen
6.2.6.1
-
8/10/2019 EMDEC troubleshooting tool
120/376
Inactive Faults, Proprietary Data Link is displayed.This tells the operat