www.Fisher.com
D10
0023
X01
2
EW Series (Designs EWD/EWS/EWT)Sliding-Stem Control Valves through10 x 8- and 12 x 8-Inch SizesThe EW Series easy-e� valves (figures 1 through 5)feature large internal cavities with expanded endconnections and a variety of unbalanced andbalanced plug designs. Sizes available from 4 x 2(1)
through 12 x 8 inches include 8 x 6 with 10-inchends and 10 x 8 inch sizes. These combinationsprovide good fluid control in economical,high-capacity valve bodies that keep valve outletvelocities within practical limits.
These valves meet a variety of service requirements,such as power plants where oversized piping is usedto limit fluid flow velocity. They also perform well innoise abatement applications; for example,high-pressure gas reducing stations where sonicvelocities are often encountered at the outlet ofconventional valve bodies.
The easy-e� Valve Family
EW Series valves are part of the versatile easy-efamily of industrial control valves from Fisher. easy-evalves share the following characteristics:
� Multiple trim material choices
� Trim temperature capability with metal seatsstandard to 800�F (427�C)
� Interchangeable, restricted-capacity trims andfull-size trims to match variable process flowdemands
� Different cage/plug styles that provide particularflow characteristics for highly-specializedapplications. The standard cage comes in threedifferent flow characteristics:
� quick-opening� linear� equal percentage
Figure 1. 12 x 6-Inch Design EWS Valve withType 667 Actuator
W2777-3 / IL
� Cavitrol� III cages are available to eliminatecavitation damage and Whisper Trim� III cages areavailable to help attenuate aerodynamic noise.
� Optional constructions allow full compliancewith National Association of Corrosion Engineers(NACE) recommendations. See page 5.
� 316 stainless steel packing box parts arestandard (including packing flange, studs, and nuts)
Product Bulletin51.1:EWFebruary 2002 EW Series
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
2
SpecificationsValve Body Configurations
See Available Configurations section
Valve Body Sizes
See table 2
End Connection Styles
Flanged: ANSI Class 300, 600, and 900raised-face or ring-type joint flanges per ASME B16.5-1996Buttwelding: Styles per ASME B16.25-1997schedules that are consistent with ASME B16.34-1996 are Schedule � 40 or � 80for all Class 300 and 600 valves, Schedule � 80or � XXS for 8 x 6-in. Class 900 valves, orSchedule � 80, � 100, or � 120 for 12 x 8-in.Class 900 valves
Maximum Inlet Pressures and Temperatures(1)
Consistent with applicable Class � 300, � 600(2),or � 900 pressure/temperature ratings per ASME B16.34-1996 unless limited as follows:Valves With All Except Cavitrol III or WhisperTrim III Cages: Where limited by individualpressure/temperature capabilities in figure 9 or 10or temperature capabilities in table 11, 12, 13, or20Valves With Cavitrol III Cages: Where limited byindividual pressure/temperature capabilities infigure 12 or temperature capabilities in table 16 or20Valves With Whisper Trim III Cages: Wherelimited by individual pressure/temperaturecapabilities in figure 15, 16, or 17 or temperaturecapabilities in table 18 or 20
Maximum Pressure Drops(1),(3)
Same as maximum inlet pressure for specificconstruction defined above, except where furtherlimited as follows:Valves With All Except Cavitrol III or WhisperTrim III Cages: See figure 9 or 10Valves With Cavitrol III Cages: See figure 12Valves With Whisper Trim III Cages: See figure15, 16, or 17, except where further restricted bythe following max �P/P1 ratio — � 0.60 for level
A cages, � 0.75 for level B cages, � 0.85 forlevel C cages, or � 0.99 for level D cages(4)
Shutoff Classifications Per ANSI/FCI 70-2-1991
See tables 3 and 4
Construction Materials
Valve, Bonnet, and Bonnet Spacer If Used:� WCB carbon steel, � LCC carbon steel,� WC9 chrome moly steel, � CF8M (316 SST),� other materials upon requestValve Plug, Cage, and Metal Seating Parts
Valve Bodies With All Except Cavitrol III orWhisper Trim III Cages: See table 5 or 14
Valve Bodies With Cavitrol III Cages: See table15
Valve Bodies With Whisper Trim III Cages: Seetable 17 to 19All Other Parts: See table 20
Material Temperature Capabilities(1)
Valve Body/Trim CombinationsValve Bodies With All Except Cavitrol III or
Whisper Trim III Cages: See figure 9 or 10 andtable 11, 12, or 13
Valve Bodies With Cavitrol III Cages: See figure12 and table 16
Valve Bodies With Whisper Trim III Cages: Seefigure 15, 16, or 17 and table 18All Other Parts: See table 20
Flow Characteristics
Standard Cages: � Quick-opening, � linear, or� equal percentageCavitrol and Whisper Trim Cages: Linear
Flow Directions
Valves with Standard CagesDesigns EWD, EWD-1, EWT, and EWT-1:
Normally down(5)
Designs EWS and EWS-1: Normally up(6)
Valves with Cavitrol Cages: Always down(5)
Valves with Whisper Trim III Cages: Alwaysup(6)
Flow Coefficients and Noise Level Prediction
Refer to Fisher Catalog 12
Port Diameters and Maximum Valve Plug Travels
See table 21– Continued –
EW SeriesProduct Bulletin51.1:EWFebruary 2002
3
Specifications (Continued)Yoke Boss and Stem Diameters
See table 21
Typical Bonnet Styles (see table 23)� Plain, � style 1 cast extension, � style 2 castextension, � ENVIRO-SEAL� bellows sealbonnet
Packing Arrangements� Standard PTFE, � Double PTFE, � Graphite,� ENVIRO-SEAL PTFE, � ENVIRO-SEALDuplex,� ENVIRO-SEAL Graphite, � HIGH-SEAL�
Approximate WeightsSee table 22
Options
� Lubricator, � lubricator/isolating valve,� drilled and tapped connection in extensionbonnet for leak-off service, � valve body drainplug, � ENVIRO-SEAL bellows seal bonnet forpositive stem sealing of hard-to-handle fluids attemperatures up to 1000�F (566�C), � style 3fabricated extension bonnet made on order to aspecific length for cryogenic service, � specialseismic service bonnet, � packings suitable fornuclear service, and � forged bonnet for 5 in.(127 mm) yoke boss on 8 x 6 in. Class 900 valve,� Class V shutoff for EWT above 450�F (232�C)using PEEK anti-extrusion rings � Class V shutofffor EWD up to 1100�F (593�C) using C-seal trim
1. The pressure/temperature limits in this bulletin and any applicable standard or code limitation should not be exceeded.2. For temperatures above 450�F (232�C), a buttwelding-end CF8M (316 stainless steel) valve body with a Class 600 pressure/temperature rating must be derated; contact your Fisher salesoffice for details. Since ANSI standards do not allow use of intermediate ratings for flanged valve bodies, a Class 600 flanged-end CF8M valve body with B7 bolting must be limited either to450�F (232�C) or to inlet pressures consistent with Class 300 ratings.3. Only 12 x 8-in. Class 900 valve bodies with threaded (-1) seat rings can take full Class 900 pressure drops; Class 900 valve bodies with clamped (no dash number) seat rings are limitedto Class 600 pressure drops. Also, there are two different 8 x 6-in. Class 900 valve bodies, one for use only with Cavitrol III cages and the other for use with all other constructions. An 8 x 6-in.Class 900 valve body with Cavitrol III cage can take full Class 900 pressure drops. For information on other 8 x 6-in. constructions that can take full Class 900 pressure drops, contact yourFisher sales office. All other 8 x 6-in. constructions are limited to Class 600 pressure drops (1440 psid flowing drop) even though installed in a Class 900 valve body.4. Restriction based on excessive noise if max �P/P1 ratio for a given cage level is exceeded.5. Down—in through cage and out through seat ring (direction shown in figure 2).6. Up—in through seat ring and out through cage as shown in figure 13.
ENVIRO-SEAL� Packing System SpecificationsApplicable Stem Diameters
� 3/4 (19.1), � 1 (25.4), and � 1-1/4 (31.8)diameter valve stems
Maximum Pressure/Temperature Limits(1)
To Meet the EPA Fugitive Emission Standardof 500 PPM(2)
For ENVIRO-SEAL PTFE and ENVIRO-SEALDuplex packing systems: full ANSI Class 300 upto 450� F (232� C)For ENVIRO-SEAL Graphite packing system:1500 psig (104 bar) at 600� F (316� C)
Construction Materials
PTFE Packing Systems:Packing Ring and Lower Wiper: PTFE V-ring(3)
Male and Female Adaptor Rings: Carbon-filledPTFE V-ringGraphite Packing Systems: Graphite ringsAnti-Extrusion Washer: Filled PTFE (notrequired for graphite packing)Lantern Ring: S31600 (316 stainless steel) (notrequired for graphite packing)Packing Box Flange: S31600Spring: � 17-7PH stainless steel or � InconelPacking Follower: S31600 lined withcarbon-filled PTFEPacking Box Studs: Strain-hardened 316stainless steelPacking Box Nuts: 316 stainless steel SA194Grade 8M
1. Refer to the valve specifications in this bulletin for pressure/temperature limits of valve parts. Do not exceed the pressure/temperature rating of the valve. Do not exceed any applicable codeor standard limitation.2. The Environmental Protection Agency (EPA) has set a limit of 500 parts per million (ppm) for fugitive emissions from a valve in selected VOC (Volatile Organic Compound) services.3. In vacuum service, it is not necessary to reverse the ENVIRO-SEAL PTFE packing rings.
The temperature limits of Design EWT valves can beextended above 450�F (232�C) by using PEEK(PolyEtherEtherKetone) anti-extrusion rings incombination with a spring-loaded PTFE seal. ThePEEK anti-extrusion rings expand to close off the
clearance gap between the plug and the cage wherethe PTFE seal may extrude at high temperaturesand pressures. The temperature limits are extended
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
4
to 600�F (316�C) for non–oxidizing service and to500�F (260�C) for oxidizing service.
NOTE: EWN Series valves with Whisper Trim IIIcages are covered in a separate bulletin.
Features
� Compliance with the Clean AirAct—Patented ENVIRO-SEAL packing systemsprovide a superior stem seal to help prevent the lossof valuable or hazardous process fluid. TheENVIRO-SEAL packing systems feature PTFE orgraphite packing with live-loading for reducedpacking maintenance.
� Noise Attenuation—In an EW Series valve,noise produced by high flow rates and largepressure drops can be reduced by up to 18 dbA witha Whisper Trim I cage and by up to 30 dbA with aWhisper Trim III cage.
� Piping Economy—Expanded end connectionsof EW Series valve bodies may reduce the need forline swages while accommodating oversized pipingarrangements used to limit fluid flow velocities.
� Temperature Compensation—On designswith the seat ring threaded into the valve body(figure 5), the hung cage feature helps reducegasketing problems caused by thermal expansionand contraction of long parts, such as the cageassembly.
� Standard Trim Parts across the easy-eproduct line—Included are FGM gaskets, packingflange, studs, and nuts.
� High-Temperature, Class IV or Class VShutoff—Optional multiple piston rings (figure 14)for Design EWD and EWD-1 valve bodies permitClass IV shutoff up to 1100�F (593�C).Use of C-seal trim (see figure 6) permits Class Vshutoff up to 1100� F (593� C).
� Increased Pressure/TemperatureRatings—12 x 8 inch Class 900 EW Series valvebodies with buttwelding end connections are capableof increased ANSI ratings called IntermediateStandard Ratings. The extra strength of the valvebody allows these valves to be used wherepressures and temperatures exceed Standard Classratings in ASME B16.34.
See Bulletin 59.1:027, IncreasedPressure/Temperature Ratings for EW Series SteelValve Bodies, for further information.
� Sour Gas Service Capability—Optionalspecial trim and bolting materials are available forapplications handling sour fluids and gases. Theseconstructions comply with the recommendations ofthe National Association of Corrosion Engineers(NACE) MR0175. Because of the care exercised byFisher in procurement and manufacturing,additional testing and documentation to assurecompliance with the NACE standard is notrequired, in most cases.
C-seal Trim DescriptionC-seal trim (figure 6) is available for valves with portdiameters from 2-7/8 inches through 8 inches.
With C-seal trim, a balanced valve can achievehigh-temperature, Class V shutoff. Because theC-seal plug seal is formed from metal (N07718nickel alloy, Inconel 718) rather than an elastomer, avalve equipped with the C-seal trim can be applied inprocesses with a fluid temperature of up to 1100�F(593�C).
ENVIRO-SEAL and HIGH-SEALPacking Systems
The ENVIRO-SEAL and HIGH-SEAL packingsystems (figure 18) from Fisher offer exceptionalsealing capabilities. These systems easily install inyour existing valves or can be purchased with newvalves. These systems help you seal your process toconserve valuable process fluid and to protect theenvironment against the emission of hazardous orpolluting fluids. The long-life and reliability of thesesystems also reduce your maintenance cost anddowntime.
For applications requiring compliance withenvironmental protection regulations, Fisher offersthe unique ENVIRO-SEAL packing system and, forhazardous service, the ENVIRO-SEAL bellows sealbonnet (figure 19). The patented emission controlpacking system or seal bonnet keeps emissionconcentrations below the EPA 500 ppm requirement.
For a superior stem seal in applications that are notenvironmentally-sensitive, Fisher offers theHIGH-SEAL graphite packing system. TheHIGH-SEAL packing system provides superiorsealing at pressure/temperature ratings beyondENVIRO-SEAL limits.
ENVIRO-SEAL packing systems, available withPTFE, graphite, or Duplex packing, and theHIGH-SEAL graphite packing system feature
EW SeriesProduct Bulletin51.1:EWFebruary 2002
5
Figure 2. Class 300 or 600 Design EWD Valve with Standard Cage
NOTE:THE 10 x 8 INCH VALVE IS SIMILAR IN APPEARANCE TO SIZES THROUGH 12 x 6 INCHES.HOWEVER, THE 10 x 8 INCH SIZE USES THE LOAD RING SHOWN FOR THE 12 x 8 INCH SIZE.IT DOES NOT USE THE CAGE RETAINER.
��������������� �����
LOAD RING
CAGERETAINER
�������������� �������� �������������
SEATRINGGASKET
SEATRING
CAGE
VALVEPLUG
GRAPHITE PISTONRING
PTFE V–RINGPACKING
PINBONNETGASKET
SHIM
SPIRALWOUNDGASKET
W2280–2*/IL
W3318-1 / IL
live-loading and unique packing-ring arrangementsfor long-term, consistent sealing performance.
NACE Standard MR0175 Compliance
Standard procurement procedures andmanufacturing processes used by Fisher assure thatcontrol valves with sour service trims comply withthe chemical and physical requirements of NACEstandard MR0175. Incoming raw materials areselected for sour service trims by specificationscovering chemical composition, forming, hardness,heat treatment, and finish. In addition, thesubsequent machining, welding, and heat treatmentof the materials being processed into finished partsis strictly regulated by manufacturing standards.
Because of strict start-to-finish manufacturing qualitymanagement, Fisher offers a high degree ofconfidence that the parts and assemblies providedfor sour service comply with MR0175. Additionaltesting and documentation to assure compliancewith MR0175 is not necessary, in most cases.
Figure 3. Design EWS trim Details Showing StandardCage and Seating Construction
CLAMPED METALSEAT RINGW0989–2/IL
However, in cases where documentation is required,the following items can be provided:
� hardness test data
� certificate of compliance to specification
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
6
Figure 4. Design EWT Trim Details
������ ������ �������������� ������������������������������������������������
SOFT BACKUPRING
SEALRING
METAL DISCRETAINER
PTFEDISCMETAL
DISC SEAT
RETAININGRING
METALBACKUPRING
SEAL RING(SHOWN POSITIONEDFOR USE WITHSTANDARD ANDCAVITROL CAGES)
SEAL RING(SHOWN POSITIONEDFOR USE WITHSTANDARD ANDCAVITROL CAGES)
��������������� ������!���� �� ��
����������� ������� �� �� ��
"��"������������������� ���� ���������������� ���
W0992–3 / IL
W0995–2 / IL
W2914–1 / IL
� heat treatment documentation
� chemical and physical test data
The requirements of the NACE standard are veryspecific and the application of the standard to controlvalve materials is quite complex. There are,however, some general guidelines that are alwaysfollowed:
� All carbon steel valve bodies and bonnets areheat-treated to 22 HRC maximum and are post-weldheat-treated.
� Martensitic and cast precipitation hardeningstainless steel are not used.
� Control valve packing sets are jam style only.
� Valve stems are made from S20910 (Nitronic 50).
� Plating and coatings are used only oversuitable base metals and are not intended forcorrosion protection.
� No machining operations that cause workhardening of the materials are performed in themanufacturing process.
� Primary trim materials are S31600 and alloy 6.
� Flat sheet gaskets are standardgraphite/S31600 (316 SST), spiral wound gasketsare standard Inconel 600/graphite.
� Bolting in NACE MR0175 (non-exposedbolting) material is provided as standard. Bolting inNACE MR0175 (exposed bolting) material isavailable as an option.
EW SeriesProduct Bulletin51.1:EWFebruary 2002
7
Figure 5. 12 x 8-Inch Class 900 Design EWT-1 Valve
SEAL RING(SHOWNPOSITIONEDFOR USEWITHSTANDARDCAGES)
THREADEDSEAT RING
W3320–2 / IL
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
8
Figure 6. C-seal Trim
PISTONRING
RETAINER
VALVE PLUG
�������
������
C-SEALMETALPLUGSEAL(1)
STAKE THREAD
C-SEALMETALPLUGSEAL(1)
1. REVERSE THE ORIENTATION OF THE C-SEAL PLUG SEALFOR PROPER SHUTOFF WHEN VALVE IS USED IN A PRO-CESS WITH DIFFERENT FLUID FLOW DIRECTION.
NOTES:
A6869 / IL
Figure 7. Typical Balanced TSO Trim
VALVE PLUGSEAL
PROTECTEDSOFT SEAT
A7096 / IL
EW SeriesProduct Bulletin51.1:EWFebruary 2002
9
Table 1. Metal Trim Part Materials for Compliance with NACE MR0175 (Sour Service) Specifications
TrimDesignation
Valve Plug Cage
Seat Ringfor StandardMetal Seat
Construction
Optional Linerfor Metal Seat
(EAT only)
Disk Seat andRetainer for
OptionalPTFE-Seat
Construction
Valve Stem, PackingFollower, LanternRing, Packing Box
Ring, and Pin
LoadRing(1)
85 S31600
S31600 withelectrolessnickel coating(ENC)
S31600 S31600 – – –
85C(2) S31600
S31600 withelectrolessnickel coating(ENC)
– – – – – – S31600
86
S31600 withseat hard facedwith CoCr-Ahardfacing alloy
S31600 withelectrolessnickel coating(ENC)
R30006 (alloy 6) – – – – – – S20910 (Valve Stem)S31600 (All Other
N05500(K-Monel)
87
S31600 withseat and guidehard faced withCoCr-Ahardfacing alloy
S31600 withelectrolessnickel coating(ENC)
R30006 (alloy 6) – – – – – –
Parts)
87C(2)
S31600 withseat and guidehard faced withCoCr-Ahardfacing alloy
S31600 withelectrolessnickel coating(ENC)
– – – – – – S31600
1. 10x8 and 12x8-inch valve body only.2. 85C and 87C are trims for PTFE-seat construction.
Figure 8. Typical Trim for NACE MR0175 Specification (Sour Service)
1600
1400
1200
1000
800
600
400
200
0
–200 –100–50
0 100 200 300 400 500
PR
ES
SU
RE
DR
OP,
PS
I
�� ������� ����������������������#���!��� ����
PR
ES
SU
RE
DR
OP,
BA
R
110
100
90
80
70
60
50
40
0
30
20
10
FLUID TEMPERATURE, °F
–100 –50 0 50 100 150 200 250
FLUID TEMPERATURE, °C
87C
2
1600
1400
1200
1000
800
600
400
200
0
–200 –100 0 100 200 300 400 500 600
PR
ES
SU
RE
DR
OP,
PS
I
�� ��������!��������������������#���!��� ����
PR
ES
SU
RE
DR
OP,
BA
R
110
100
90
80
70
60
50
40
0
30
20
10
FLUID TEMPERATURE, °F
–100 –50 0 50 100 150 200 250
FLUID TEMPERATURE, °C
300
450
86 87
85 1
4
2
3
NOTES:USE TRIM 87 INSTEAD OF TRIM 85 FOR NONLUBRICATING
FLUIDS SUCH AS SUPERHEATED STEAM OR DRY GASESBETWEEN 300°F (149°C) AND 600°F (316°C).
DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED,EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
1
2
85C
USE TRIM 85 UP TO 1440 PSI (99 BAR) WITH CLEANDRY GAS. FOR PROCESS FLUIDS OTHER THAN CLEAN DRY GAS,USE TRIM 85 ONLY UP TO 300 PSI (21 BAR).
TRIM 87 TEMPERATURE LIMIT CAN BE EXTENDED ABOVE 450°F (232°C)F IF PEEK ANTI-EXTRUSION RINGS AND SPRING–LOADED SEAL RING ARE USED.
3
4
A3115–3 / IL
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
10
Table 2. Available Valve Constructions(1)
VALVE SIZE(2), INCHES
VALVE Class 300 or 600 Class 900VALVEDESIGN
4 x 2 6 x 4 8 x 4 8 x 6 8 x 6 with10-inch ends
12 x 6 10 x 8 12 x 8 8 x 6 12 x 8
EWDEWD-1EWSEWS-1EWTEWT-1
x- - -x
- - -x
- - -
x- - -x
- - -x
- - -
x- - -x
- - -x
- - -
x- - -x
- - -x
- - -
x- - -x
- - -x
- - -
x- - -x
- - -x
- - -
x- - -x
- - -x
- - -
x- - -x
- - -x
- - -
x- - -x
- - -x
- - -
xxxxxx
1. X indicates available construction.2. Two-number valve size designates end connection size x trim size.
Available ConfigurationsAll configurations covered in this bulletin use asingle-port, globe-style valve body with cage guidingand push-down-to-close valve plug action. Thisvalve style is combined with different plug styles andeither a clamped seat ring (no dash number suffix)or a seat ring threaded into the valve body (-1 suffix).
Design EWD: Balanced valve plug (figure 2) withclamped seat ring and metal-to-metal seating for allgeneral applications over a wide range of pressuredrops and temperatures.
Design EWD-1: 12 x 8 inch Class 900 Design EWDvalve body, with threaded seat ring.
Design EWS: Unbalanced valve plug (figure 3) withclamped seat ring and metal-to-metal or optionalmetal-to-PTFE seating for all general applicationsrequiring better shutoff capabilities than can beobtained with the Design EWD valve body.
Design EWS-1: 12 x 8 inch Class 900 Design EWSvalve body, with threaded seat ring andmetal-to-metal seating.
Design EWT: Balanced valve plug (figure 4) withmetal-to-PTFE seating (for stringent shutoffrequirements) standard in all Design EWT valves(except those with Cavitrol III cages). Metal-to-metalseating for higher temperatures is standard for allDesign EWT valve bodies with Cavitrol III cages andoptional for these valves with other cages.
Design EWT-1: 12 x 8 inch Class 900 Design EWTvalve body, with threaded seat ring and withmetal-to-metal seating (figure 5).
Material Selection GuidelinesRegardless of valve construction, select the valvebody/bonnet material from the specifications table,
keeping in mind that the valve service conditionscannot exceed the ASME/ANSIpressure/temperature limitations for the selectedvalve body. Then, perform steps 1 and 2 under theappropriate valve design heading to complete theselection process.
Design EWD, EWS, or EWT Valve With All ExceptCavitrol III or Whisper Trim III Cages
1. Choose a trim combination for the serviceconditions according to figure 9, while making surefrom table 5 that this combination provides thedesired trim materials. Then, make sure from table11, 12, or 13 that the valve body/trim temperaturelimits are not exceeded.
2. Finally, check in table 20 that packing and othervalve parts are available in materials that meet thedesired service conditions.
Design EWD-1, EWS-1, or EWT-1 Valve WithStandard Cage
1. Choose a trim combination for the serviceconditions according to figure 10, while making surefrom table 7 that this combination provides thedesired trim materials.
2. Finally, check in table 20 that packing and othervalve parts are available in materials that meet thedesired service conditions.
Design EWT Valve With Cavitrol III Cage1. Choose a trim combination for the serviceconditions according to figure 12, while making surefrom table 15 that this combination provides thedesired trim materials. Then, make sure from table16 that the valve body/trim temperature limits are notexceeded.
EW SeriesProduct Bulletin51.1:EWFebruary 2002
11
Table 3. Shutoff Classifications per ANSI/FCI 70-2-1991Valve Design Seating Shutoff Class
EWD or EWD-1 Metal II (standard)
III (optional for 6 x 4 through 12 x 6 inch valves with optionalgraphite piston ring; optional for 10 x 8 and 12 x 8 inch valveswith optional double piston rings)
IV (optional for 6 x 4 through 12 x 8 inch valves withoptional multiple graphite piston rings)
EWS or EWS-1 Metal IV (standard)
V (optional, consult your Fisher sales office)
EWS PTFE VI
EWT with all except PTFE Standard air test (maximum leakage is 0.05 mL/min/psid/inch port diameter)Cavitrol III cages V (optional)
Metal IV
V(1)
EWT with Metal IV (standard)1-stage Cavitrol III cage V (optional)
EWT with 2-stageCavitrol III cage or2- or 3-stage Cavitrol IIIcage
Metal or PTFE V
EWT-1 Metal IV1. Class V shutoff for Design EWT requires spring-loaded seal ring, radius-seat plug, and wide-bevel seat ring. Not available with 8-inch port, quick-opening cage. Not available withS31600 (316 SST) valve plug and seat ring (trims 4, 29, 85, 310).
Table 4. C-seal Shutoff Classification
Valve Design (Class) Valve Size, Inches Port Diameter, Inches(mm)
Cage Style ANSI Leakage Class
6 x 4 x 2-1/2 2-7/8 (73) Eq. %, Linear, Whisper I, Cav III (2-stage)
6 x 48 x 4
4-3/8 (111.1) Eq. %, Linear, Whisper I, Cav III (1-stage)V to 1100�F (593�C)
Design EWD8 x 612 x 6
5-3/8 (136.5) Whisper III (A3, B3, D3, D3), Cav III (2-stage)
V to 1100 F (593 C)(for port
diameters from 2-7/8(Class 300, 600)
8 x 612 x 6
7 (177.8) Eq. %, Linear, Whisper I, Cav III (1-stage)
diameters from 2-7/8 through 8-inch withoptional C-seal trim)
10 x 812 x 8
8 (203.2) Eq. %, Linear, Whisper I, Cav III (1-stage)
2. Finally, check in table 20 that packing and othervalve parts are available in materials that meet thedesired service conditions.
Design EWD, EWS, or EWT Valve With WhisperTrim III Cage
1. Choose a trim combination for the serviceconditions according to figure 15, while making surefrom table 17 that this combination provides thedesired trim materials. Then, make sure from table18 that the valve body/trim temperature limits are notexceeded.
2. Finally, check in table 20 that packing and othervalve parts are available in materials that meet thedesired service conditions.
Design EWD-1, or EWT-1 Valve With WhisperTrim III Cage
1. Choose a trim combination for the serviceconditions according to figure 16 or 17, while makingsure from table 19 that this combination provides thedesired trim materials.
2. Finally, check in table 20 that packing and othervalve parts are available in materials that meet thedesired service conditions.
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
12
Table 5. Design EWD, EWS, and EWT Metal Trim Part Combinations(1) Except for Valves with Cavitrol III or Whisper Trim III CagesSEAT
TRIM DESIGNATIONS VALVE PLUG CAGE Disk Seat, Retainerfor PTFE SeatConstructions
Seat Ringfor Metal SeatConstructions
1 (standard trim for all valves exceptDesign EWT and those in CF8M.Trim 57 is standard for Design EWT.Trim 29 is standard for all valves inCF8M)
S41600 hardenedto 38 HRC(minimum)
CB7CU-1 (S17400)hardened to40 HRC (minimum)
- - - � S41600 for Types EWD, EWS� S41000 for 8 x 6-inch, Class900 Types EWD, EWS� CA6NM for Types EWD-1,EWS-1, EWT-1
3 and 3H(2) S31600 w/seat andguide hard facedw/CoCr-Ahardfacing alloy
R30006 (alloy 6)(3) S31600 w/seat hard facedw/CoCr-A hardfacing alloy(4)
S31600w/seat hard faced w/CoCr-Ahardfacing alloy(4)
4 S31600 CB7CU-1 (S17400)hardened to40 HRC (minimum)
S31600 S31600
27 S31600 w/seat andguide hard facedw/CoCr-Ahardfacing alloy
CF8M w/electrolessnickel coating(ENC)
S31600 w/seat hard facedw/CoCr-A hardfacing alloy(4)
S31600 w/seat hard facedw/CoCr-A hardfacing alloy(4)
29 (standard for all valvesin CF8M)
S31600 CF8M w/electrolessnickel coating (ENC)
S31600 S31600
37 and 37H(2) S31600 w/seat andguide hard facedw/CoCr-Ahardfacing alloy
CB7CU-1 (S17400)hardened to40 HRC (minimum)
S31600 w/seat hard facedw/CoCr-A hardfacing alloy(4)
S31600 w/seat hard facedw/CoCr-A hardfacing alloy(4)
57 (standard for all Design EWTvalve bodies in all materialsexcept CF8M)
S41600 hardenedto 38 HRC(minimum)
CB7CU-1 (S17400)hardened to40 HRC (minimum)
S31600 - - -
1. Nonferrous alloy combinations are also available. Consult your Fisher sales office for details.2. Trims 3H and 37H have clearances for high-temperature service.3. Available only in linear, quick-opening, equal percentage, and Whisper Trim I cages.4. Solid cast alloy 6 seat ring is used instead for 4 x 2, 10 x 8, and 12 x 8 inch valve sizes.
ANSI/FCI Class VI Shut-off CapabilitiesDesign EWS valves with metal seat constructions and Design EWT valves with soft seat and metal seatconstructions can provide ANSI/FCI Class VI shut-off capabilities. See tables 6 and 7.
Table 6. Class VI Shut-off AvailabilityType Port Size, Inches Seat Minimum Seat Load
EWS � 7 Metal 300 lbs/lineal inch
EWT � 3-7/16 � 7 Soft See Catalog 14
EWT � 3-7/16 � 7 Metal 300 lbs/lineal inch
Table 7. Class VI Trim Materials
CAGE/SEAT TRIM TEMPERATURE LIMITTYPE CAGE/SEAT
RING RETAINERVALVE PLUG SEAT RING SEAL RING
�F �C
EWSS31600 (316 SST)
/ ENC
S31600/CoCr-A (alloy6) seat w/ radiused
seat (special design)
S31600 w/ widebeveled seat (special
design)NA Not a limiting factor Not a limiting factor
S31600 / ENCS31600 w/ standard
beveled seatS31600/PTFE UHMWPE(1) Elgiloy –20 to 150 –29 to 66
S31600 / ENCS31600/CoCr-A seat
w/ radiused seat(special design)
S31600 w/ widebeveled seat (special
design)UHMWPE Elgiloy –150 to 150 –101 to 66
EWTS17400 (17-4PH SST)
S41600 w/ standardbeveled seat
S31600/PTFE UHMWPE Elgiloy –20 to 150 –29 to 66
S17400S41600 w/ radiusedseat (special design)
S31600 w/ widebeveled seat (special
design)UHMWPE Elgiloy –20 to 150 –29 to 66
1. UHMWPE (Ultra High Molecular Weight Polyethylene)
EW SeriesProduct Bulletin51.1:EWFebruary 2002
13
Fisher TSO (Tight Shutoff) Trim CapabilitiesSee figure 7 and tables 8, 9, and 10. For additional information contact your Fisher sales office.
Table 8. TSO (Tight Shutoff) Leakage ClassLeakage Class Maximum Leakage Test Medium Test Pressure Test Procedure
TSO (TightShutoff)
Valves with TSO trim are factorytested to a more stringent Fisher testrequirement of no leakage at time ofshipment.
Water Service ∆P(1) ANSI/FCI Class V test procedure B
1. Specify service ∆P when ordering.
Table 9. TSO Shutoff AvailabilityLEAK CLASS
TYPE CONSTRUCTIONStandard Optional
EWT Std or Cavitrol III trim. Replaceable, protected soft seat TSO - - -
Table 10. Port Diameters, Valve Plug Travel, Yoke Boss Diameters for TSO (Tight Shutoff) TrimPORT DIAMETER C REDUCTION
VALVE TYPE TRIMMAX TRAVEL YOKE BOSS SIZE
Nominal Actual TSOCV REDUCTION
AT 100%VALVE TYPE TRIMInch mm Inch mm Inch mm Inch mm
AT 100%TRAVEL(1)
EWT 6x4-Inch Std 2 50.8 3-9/16 90 4-3/8 111 4-3/16 106 4% (linear)3% (equal percent)
EWT 8x6-Inch Std2 50.8 3-9/16
590127 7 179 6-13/16 173
2%EWT 8x6-Inch Std
4 102 3-9/16 907 179 6-13/16 173
2%1. This column lists the percent reduction of published maximum CV of the trim listed in the TRIM column.
Installation
Unless limited by seismic criteria, the valve body canbe installed in any position (as long as sufficientsupport is provided if a fabricated extension bonnetis used). However, the normal method is with theactuator vertical above the valve, since nonverticalpositions may cause uneven trim wear and
decreased trim life.
Flow through the valve body must be in the directionindicated by the flow direction arrow on the valvebody. Consider installing an upstream strainer,especially if the valve body includes slotted ormultihole Whisper Trim or Cavitrol cages.
Dimensions are shown in figure 20.
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
14
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
BA
R
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °C
USE TRIM 27 INSTEAD OF TRIM 29 FOR NON–LUBRICATING FLUIDS SUCH AS SUPERHEATED STEAM OR DRY GASES BETWEEN 300°F (149°C) AND 600°F (316°C).
TRIMS 4 AND 29 MAY BE USED OVER 300 PSI ONLY WITHCLEAN, DRY GAS.
Figure 9. Typical Trim Used in Design EWD, EWS, or EWT Valves Except Those with Cavitrol III or Whisper Trim III Cages
FLUID TEMPERATURE, °C
FLUID TEMPERATURE, °C
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
PS
I
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °F
PR
ES
SU
RE
DR
OP,
BA
RP
RE
SS
UR
E D
RO
P, B
AR
� �����������������������������$$� �%$$#���!��� ����
�����������$$� �%$$��#� �����������#��
�����������$$� �%$$���%� !��!���������#��
�����������$$� �%$$���!����������#��
NOTES:BE ESPECIALLY CAREFUL TO SPECIFY SERVICE TEMPERATURE IF TRIM
3,4, OR 37 IS SELECTED, AS DIFFERENT THERMAL EXPANSION RATES REQUIRE SPECIAL PLUG CLEARANCES, ALSO, USE TRIM 37H INSTEAD OFTRIM 4 FOR NON–LUBRICATING FLUIDS SUCH AS SUPERHEATED STEAM ORDRY GASES BETWEEN 300°F (149°C) AND 600°F (316°C).
DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED,EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
1
2
3
4
A6334–1 / IL
2 2
2 2
-20
FLUID TEMPERATURE, °C
PR
ES
SU
RE
DR
OP,
PS
I
FLUID TEMPERATURE, °F
PR
ES
SU
RE
DR
OP,
BA
R
1050
EW SeriesProduct Bulletin51.1:EWFebruary 2002
15
Table 11. Valve/Trim Temperature Capabilities(1) for Class 300 or 600 Design EWD, EWS, and EWT Valves with2-Inch (51 mm) or 3-Inch (76 mm) Travel (Except those with Cavitrol III or Whisper Trim III Cages)
MATERIAL TEMPERATURE CAPABILITYVALVE/BONNET TRIM DESIGNATION VALVE SIZE,
�F �CMATERIAL FROM TABLE 5 INCHES
Min Max Min Max
1
4 x 26 x 48 x 48 x 612 x 612 x 8 & 10 x 8
–20–20–20–20–20–20
750650625600500800
–29–29–29–29–29–29
399343329316260427
WCB steel29
4 x 26 x 48 x 48 x 612 x 612 x 8 & 10 x 8
–20–20–20–20–20–20
600430425400345600
–29–29–29–29–29–29
316221218204174316
37 4 x 2 through 12 x 8 –20 410 –29 210
37H 4 x 2 through 12 x 8 410 800 210 427
57 4 x 2 through 12 x 8 –20 400 –29 204
1
4 x 26 x 48 x 48 x 612 x 610 x 8
–20–20–20–20–20–20
700650625625500650
–29–29–29–29–29–29
371343329329260343
57 4 x 2 through 10 x 8 –20 400 –29 204
LCC steel
29
4 x 26 x 48 x 48 x 612 x 610 x 8
–50–50–50–50–50–50
600425425400325600
–46–46–46–46–46–46
316218218204163316
37 4 x 2 through 12 x 8 –20 410 –29 210
37H 4 x 2 through 12 x 8 410 700 210 371
1
4 x 26 x 48 x 48 x 612 x 612 x 8 & 10 x 8
–20–20–20–20–20–20
750650625600500800
–29–29–29–29–29–29
399343329316260427
3 4 x 2 through 12 x 8 –20 800 –29 427
3H 4 x 2 through 12 x 8 800 1050 427 566
WC9 chrome moly steel27
4 x 26 x 48 x 48 x 612 x 612 x 8 & 10 x 8
–20–20–20–20–20–20
650430425400325650
–29–29–29–29–29–29
343221218204163343
29
4 x 26 x 48 x 48 x 612 x 612 x 8 & 10 x 8
–20–20–20–20–20–20
600430425400325600
–29–29–29–29–29–29
316221218204163316
37 4 x 2 thru 12 x 8 –20 410 –29 210
37H 4 x 2 thru 12 x 8 410 800 210 427
57 4 x 2 through 12 x 8 –20 400 –29 204
27 4 x 2 through 12 x 8 –325(6) 650 –198(6) 343CF8M (316 SST)(5)
29 4 x 2 through 12 x 8 –325(6) 600 –198(6) 3161. For metal trim parts only.2. Except 550�F (288�C) for trim 29.3. Except 600�F (316�C) for trim 26.4. Except 450�F (232�C) for trim 29.5. For temperatures above 450�F (232�C), buttwelding-end CF8M valves having a Class 600 pressure-temperature rating must be derated; contact your Fisher sales office for further information.Since ANSI standards do not allow use of intermediate pressure-temperature ratings for flanged valves, flanged-end CF8M valves having a Class 600 pressure-temperature rating must be limitedto 450�F (232�C) or must be limited to inlet pressures that are consistent with the Class 300 pressure-temperature rating.6. May be used down to –425�F (–254�C) if manufacturing process includes Charpy Impact test.
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
16
Table 12. 4-Inch (102 mm) Travel Whisper Trim I DesignEWD and EWT Valve Body/Trim Temperature Capabilities(1) (Class 150 - 600 and Size 8 x 6, Class 900)
BODY/BONNETTRIM
MATERIAL TEMPERATURECAPABILITYBODY/BONNET
MATERIAL(2) DESIGNATION VALVE SIZE, INCH�F �CMATERIAL FROM TABLE 5
Min Max Min Max
1 8 x 612 x 6
–20–20
625545
–29–29
329285
3 8 x 6 or 12 x 6 –20 800 –29 427
WCB steel 57 8 x 6 or 12 x 6 –20 400 –29 204WCB steel37 8 x 6 or 12 x 6 –20 410 –29 210
37H 8 x 612 x 6
410410
800685
210210
427363
1 8 x 6 only –20 625 –29 329
4, 57 8 x 6 only –20 400 –29 204LCC steel
37 8 x 6 only –20 410 –29 210
37H 8 x 6 only 410 650 210 343
3 8 x 6 or 12 x 6 –20 800 –29 427WC9 chrome moly steel
3H 8 x 6 or 12 x 6 800 1050 427 5661. For metal trim parts only.2. Same material also used for bonnet spacer.
Table 13. Class 900 Design EWD, EWS, and EWT Valve Body/Trim Temperature Capabilities(1)
BODY/BONNET TRIM DESIGNATION VALVE
MATERIAL TEMPERATURECAPABILITYBODY/BONNET
MATERIALTRIM DESIGNATION
FROM TABLE 5VALVE
SIZE, INCH �F �CMATERIAL FROM TABLE 5 SIZE, INCHMin Max Min Max
18 x 612 x 8
–20–20
600800
–29–29
316427
WCB steel29
8 x 612 x 8
–20–20
400600
–29–29
204316WCB steel
37 8 x 6 or 12 x 8 –20 410 –29 210
37H 8 x 6 or 12 x 8 410 800 210 427
57 8 x 6 or 12 x 8 –20 400 –29 204
1 8 x 6 only –20 625 –29 329
4, 37 8 x 6 only –50 410 –46 210
LCC steel 37H 8 x 6 only 410 700 210 371LCC steel57 8 x 6 only –20 400 –29 204
29 8 x 6 only –50 400 –46 204
18 x 612 x 8
–20–20
600800
–29–29
316427
3 8 x 6 –20 800 –29 427
3H 8 x 6 800 1050 427 566
3 12 x 8 –20 800 –29 427
3H 12 x 8 800 1050 427 566
WC9 chrome moly steel27
8 x 612 x 8
–20–20
400650
–29–29
204343
298 x 612 x 8
–20–20
400600
–29–29
204316
37 8 x 6 or 12 x 8 –20 410 –29 210
37H 8 x 6 or 12 x 8 410 800 210 427
57 8 x 6 or 12 x 8 –20 400 –29 204
27 8 x 6 or 12 x 8 –325(2) 650 –198(2) 343316 SST (CF8M)
29 8 x 6 or 12 x 8 –325(2) 600 –198(2) 3161. For metal trim parts only.2. May be used down to –425�F (–254�C) if manufacturing process includes Charpy impact test.
EW SeriesProduct Bulletin51.1:EWFebruary 2002
17
Figure 10. Typical Trim Used in Design EWD-1, EWS-1, and EWT-1 Valves with Standard Cages
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
BA
R
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °C FLUID TEMPERATURE, °C
FLUID TEMPERATURE, °C
PR
ES
SU
RE
DR
OP,
PS
IP
RE
SS
UR
E D
RO
P, P
SI
PR
ES
SU
RE
DR
OP,
BA
RP
RE
SS
UR
E D
RO
P, B
AR
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °F
A6334–1 / IL
������#�������#��
������%�� !��!���������#��
�������!�����������#��
NOTE:DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE
FOR THE CLASS RATING OF THE BODY MATERIAL USED,EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
1
1
1
1
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
18
Table 14. Class 900, 12 x 8 Inch, Design EWD-1, EWS-1, and EWT-1 Metal Trim PartCombinations Except for Valves with Whisper Trim III CagesTrim
DesignationValve Plug Cage Seat Ring
1 S41600 (416 SST) hardened to38 Rockwell C (min)
CB7CU-1 (17-4PH SST) with H900heat-treat condition
Heat-treated CA6NM(1)
27 316 SST with seat and guidehard-faced with CoCr-A
316 SST with electrolessnickel coating (ENC)
316 SST with seathard-faced with CoCr-A
37 & 37H(2) S31600 with seat and guidehard-faced with CoCr-A
CB7CU-1 with H900heat-treat condition
S31600 with seathard-faced with CoCr-A
1. CA6NM is similar to 410 SST.2. Trim 37H has clearances for high-temperature service.
Figure 11. Detail of 2-Stage Cavitrol III Cage in Class 300 or 600 Design EWT Valve
W3331–1 / IL
CAGERETAINER/BONNETSPACER
Figure 12. Typical Trim Used in Cavitrol III Cage Constructions with Steel or Stainless Steel Valves
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
BA
R
LIQUID TEMPERATURE, °F
LIQUID TEMPERATURE, °C
NOTE:DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE FOR THE CLASS RATING OF THE BODY MATERIAL USED,EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
A2732 / IL
EW SeriesProduct Bulletin51.1:EWFebruary 2002
19
Figure 13. Design EWT Metal-Seat Valve withWhisper Trim I Cage
W0997–2 / IL
BACKUPRING
SEAL RING
CAGE
Figure 14. 8 x 6-Inch Design EWD Valve withWhisper Trim III Cage
OPTIONAL TRIPLE PISTONRINGS USED TO OBTAINCLASS IV SHUTOFF (THISOPTIONAL SHUTOFF ALSOAVAILABLE IN OTHERDESIGN EWDSIZES ANDCONSTRUC–TIONS)
CAGERETAINER
BONNETSPACER
BAFFLE
W3361–1 / IL
Figure 15. Typical Trim Used in Design EWD, EWS, and EWT Valves with Whisper Trim III Cages
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
BA
R
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °C
NOTE:DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE
FOR THE CLASS RATING OF THE BODY MATERIAL USED,EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
FLUID TEMPERATURE, °C
PR
ES
SU
RE
DR
OP,
BA
R
PR
ES
SU
RE
DR
OP,
PS
I
FLUID TEMPERATURE, °F
A6334 / IL
�����������$$���#������� ��%�� !��!���"��"�
�����������$$���!����������"��"�1 1
1
1050
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
20
Table 15. Cavitrol III(1) Metal Trim Part CombinationTrim
DesignationValve Plug Cage Cage Retainer(2) Seat Ring
76 Heat-treated S42000 (420 SST) S17400 (17-4PH SST) withH900 heat-treat condition
S31600 (316 SST) S17400 with H900heat-treat condition
1. Available only in Design EWT valve.2. Not used in 12 x 8 or 8 x 6 inch Class 900 valves.
Table 16. Cavitrol III Valve Body/Trim Temperature Capabilities
TRIM DESIGNATION FROM TABLE 15 VALVE BODY & BONNETMATERIAL TEMPERATURE
CAPABILITYTRIM DESIGNATION FROM TABLE 15 VALVE BODY & BONNETMinimum Maximum
WCB carbon steel or WC9 chrome moly steel –20�F (–29�C) These materialsLCC carbon steel –50�F (–46�C)
These materialsnot limiting factors
76
4 x 2 inch valve size6 x 4 inch valve size8 x 4 inch valve size
–20�F (–29�C)–20�F (–29�C)–20�F (–29�C)
400�F (204�C)300�F (149�C)275�F (135�C)
S31600 (316 SST)8 x 6 inch valve size(1)
12 x 6 inch valve size12 x 8 inch valve size(2)
–20�F (–29�C)–20�F (–29�C)–20�F (–29�C)
250�F (121�C)225�F (107�C)350�F (177�C)
1. This valve body/trim combination not available in Class 900 valve.2. This valve body/trim combination available in all 12 x 8 inch rating classes.
Table 17. Metal Trim Part Combinations for Design EWD, EWS, and EWT Valves with Whisper Trim III Cages(1)
TrimDesignation
Valve Plug Cage CageRetainer
Baffle(for LevelD3 Cage
Only)
Disk Seat andRetainer forPTFE-Seat
Construction
Seat Ringfor Metal-SeatConstruction
301 (standard forall valve materialsexcept CF8M [316 SST])
S17400 (17-4PH SST)hardened to 40HRC (min)
S41600 (416 SST)hardened to 38HRC (min)
WCB/A105 heat-treated 22 HRC(NACE with ENC)
Steel - - -S41600 (416 SST)hardened to 38HRC (min)
301CS17400 (17-4PH SST)hardened to 40HRC (min)
S41600 (416 SST)hardened to 38HRC (min)
WCB/A105 heat-treated 22 HRC(NACE with ENC)
SteelS31600(316 SST)
- - -
304S31600 with seat andguide hard-faced withCoCr-A (Alloy 6)
S41600 hardenedto 38 HRC(min)
WCB/A105 heat-treated 22 HRC(NACE with ENC)
Steel - - -S31600 with seathard-faced withCoCr-A
310 (standardfor CF8M valves)
S31600S31600 withelectroless nickelcoating (ENC)
S31600 with ENC S31600 S31600 S31600
313 (NACE compatible)(2)S31600 with seat andguide hard-faced withCoCr-A
S31600 withelectroless nickelcoating (ENC)
WCB/A105 heat-treated 22 HRC(NACE with ENC)
Steel - - -S31600 with seathard-faced withCoCr-A
313C (NACE compatible)(2)S31600 with seat andguide hard-faced withCoCr-A
S31600 withelectroless nickelcoating (ENC)
WCB/A105 heat-treated 22 HRC(NACE with ENC)
Steel S31600 - - -
315S31600 with seat andguide hard-faced withCoCr-A
ElectrolizedS31600
Electrolized S31600 S31600 - - -S31600 with seathard-faced withCoCr-A
317S31600 with seat andguide hard-faced withCoCr-A
WC9/Ion Nitrided WCB/Ion Nitrided Steel - - - S41600
318S31600 with seat andguide hard-faced withCoCr-A
WC9/Ion Nitrided WC9/Ion Nitrided WC9 - - -S31600 with seathard-faced withCoCr-A
1. For 8 x 6 or 12 x 6 -inch valves only.2. Level D3 cage cannot be certified to NACE. Use 316/ENC cage retainer instead.
EW SeriesProduct Bulletin51.1:EWFebruary 2002
21
Table 18. Valve/Trim Temperature Capabilities for Design EWD, EWS, and EWT Valves with Whisper Trim III Cages
VALVE/BONNET/ MATERIAL TEMPERATURE CAPABILITYVALVE/BONNET/BONNET SPACER
TRIM DESIGNATION VALVE SIZE,�F �CBONNET SPACER
MATERIALFROM TABLE 17 INCHES
Min Max Min Max
301 8 x 612 x 6
–20–20
640595
–29–29
338313
301C (for soft seats) 8 x 6, 12 x 6 –20 400 –29 204
304 8 x 612 x 6
–20–20
650640
–29–29
343338
WCB steel or WC9313 (NACE compatible) 8 x 6
12 x 6–20–20
450400
–29–29
232204WCB steel or WC9
chrome moly steel 313C (NACE compatible)(for soft seats)
8 x 612 x 6
–20–20
400400
–29–29
204204
315 8 x 612 x 6
–20–20
400350
–29–29
204177
317 8 x 6, 12 x 6 –20 800 –29 427
318 (WCB only) 8 x 6, 12 x 6 –20 800 –29 427
318 (WC9 only) 8 x 6, 12 x 6 –20 1100 –29 593
301, 301C (for softseats), 304
8 x 612 x 6
–20–20
300250
–29–29
149121
310 8 x 6, 12 x 6 –325 300 –198 149CF8M (316 SST) 313 8 x 6, 12 x 6 –20 600 –29 316
313C (for soft seats) 8 x 6, 12 x 6 –20 400 –29 204
315 8 x 6, 12 x 6 –325 800(1) –198 427(1)
1. May be used up to 1000�F (538�C) if manufacturing process controls carbon content to 0.04% minimum or 0.08% maximum.
Table 19. Design EWD–1 and EWT–1 Metal Trim Part Combinations for Valves with Whisper Trim III CagesTrim Designation Valve Plug Cage Seat Ring
I Heat-treated CA6NM(1) CB7CU-1 (17-4PH SST) withH1025 heat-treat condition
Heat-treated CA6NM
II S31600 (316 SST) with seat andguide hard faced with CoCr-A
CB7CU-1 with H1025heat-treat condition
Inconel 600 with seathard faced with CoCr-A
IVCF8M (316 SST) with seat andguide hard faced withCoCr-A
CB7CU-1 with H0125heat-treat condition
CF8M with seathard faced with CoCr-A
1. CA6NM is similar to 410 SST.
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
22
Figure 16. Typical Trim Used in Design EWD-1 Valves with Whisper Trim III Cages
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
BA
R
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °C
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
BA
R
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °C
���������� �� !��!���������"��"� �������!�����������"��"�
NOTE:DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE
FOR THE CLASS RATING OF THE BODY MATERIAL USED,EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
1
1
1
MAY BE USED DOWN TO –150°F (–101°C) WITH LEVEL A, B,OR C CAGE, OR WITH LEVEL D CAGE THAT HAS AN 18–8 SSTBAFFLE.
2
B1484–1 / IL
EW SeriesProduct Bulletin51.1:EWFebruary 2002
23
Figure 17. Typical Trim Used in Design EWT-1 Valves with Whisper Trim III Cages
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
BA
R
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °C
PR
ES
SU
RE
DR
OP,
PS
I
PR
ES
SU
RE
DR
OP,
BA
R
FLUID TEMPERATURE, °F
FLUID TEMPERATURE, °C
���������� �� !��!���������"��"� �������!�����������"��"�
NOTE:DO NOT EXCEED THE MAXIMUM PRESSURE AND TEMPERATURE
RATING FOR THE CLASS RATING OF THE BODY MATERIAL USED,EVEN THOUGH THE TRIMS SHOWN MAY HAVE HIGHER CAPABILITIES.
1
1
1
MAY BE USED DOWN TO –150°F (–101°C) WITH LEVEL A, B,OR C CAGE, OR WITH LEVEL D CAGE THAT HAS AN 18–8 SSTBAFFLE.
2
A2733-1 / IL
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
24
Table 20. Materials and Temperature Limitations for Other Parts
PART MATERIAL
MATERIALTEMPERATURE
CAPABILITYPART MATERIAL�F �C
Min Max Min Max
WCB or WC9 valve Studs Steel SA-193-B7, or steel SA-193-B7M for sour gasWCB or WC9 valvebody Nuts Steel SA-194-2H, or steel SA-194-2M for sour gas
–20 800 –29 427
Studs Steel SA-193-B7LCC valve body
Nuts Steel SA-194-2H–50 700 –46 371
Studs Steel SA-193-B16WC9 valve body
Nuts Steel SA-194-7–20 1100 –29 593
Body-to-bonnet Studs Steel SA-193-B7bolting (see table 24 Nuts Steel SA-194-2H
–50 800 –46 427
for NACE boltingmaterials and Studs Steel SA-193-B7M for sour gas –50 800 –46 427materials andtemperature limits) Nuts Steel SA-194-2HM for sour gas –50 650 –46 343temperature limits)
CF8M (316 SST) Studs 304 SST SA-320-B8CF8M (316 SST)valve body Nuts 304 SST SA-194-8
–425 100 –254 38
Studs 316 SST SA-193-B8M (strain hardened)
Nuts 316 SST SA-194-8M–325(1) 800 –198(1) 427
Studs 316 SST SA-193-B8M
Nuts 316 SST SA-194-8M–325(1) 1200 –198(1) 649
Disk (all soft-seat constructions) PTFE –100 400 –73 204
–50(2) 800 –46(2) 427Std. for 4 x 2 thru 12 x 6 inch sizes Graphite (FMS 17F27)
–50(2) 900 –46(2) 482Design EWD
Std. for 10 x 8 & 12 x 8 inch Graphite Oxidizing service—all sizes –50(2) 1000 –46(2) 538piston ring Std. for 10 x 8 & 12 x 8 inchsize; optional for 4 x 2thru 12 x 6 inch sizes
GraphiteFMS17F39
Nonoxidizingservice
12 x 8 Class 900 and 12 x8 Class 600 & smaller
–50(2) 1100 –46(2) 593
Fluoroelastomer(3) 0 400 –18 204
Standard 4 x 2 through 12 x 6 inch Design Ethylene-propylene(4) –40 450 –40 232Standard 4 x 2 through 12 x 6 inch DesignEWT valve plug seal (except valve with
Backup ringFor use with hydrocarbons –30 160 –34 71EWT valve plug seal (except valve with
Cavitrol III cage) Nitrile(5)For use with other fluids –30 200 –34 93
Seal ring Carbon-filled PTFE –100 450 –73 232
Spring-loaded Design EWT or EWT-1 valve Backup ring S41600 (416 SST) –20 800 –29 427plug seal (6) (standard for 10 x 8 & Retaining ring S30200 (302 SST) –425 1100 –254 59312 x 8 inch valve regardless of cage and all4 x 2 through 12 x 6 inch valves with Cavitrol Seal ring PTFE with Hastelloy C Spring –100 450(10) –73 232(10)4 x 2 through 12 x 6 inch valves with CavitrolIII cage; optional in 4 x 2 through 12 x 6inch valves with other than Cavitrol III cages)
Anti-extru-sion rings
PEEK (PolyEtherEtherKetone) - - -(11) - - -(11)
Valve plug stem and pin S31600 (316 SST) –325(1) 1100 –198(1) 593
CB7CU-1 (17-4PH SST) –150 600 –102 316Load ring (10 x 8 & 12 x 8 inch Design N07718 (Inconel(7) 718) –425 1100 –254 593EWD, EWS, & EWT only)
N05500 (K-Monel(7)) –400 500 –240 260
FGM (standard) –325 1100 –198 593Seat ring, bonnet and cage gaskets
PTFE-coated Monel –100 300 –73 149
Spiral wound gaskets Inconel 600(7)/laminated graphite FGM (standard) –325 1100 –198 593-continued-
EW SeriesProduct Bulletin51.1:EWFebruary 2002
25
Table 20. Materials and Temperature Limitations for Other Parts (Continued)
PART MATERIAL
MATERIALTEMPERATURE
CAPABILITYPART MATERIAL�F �C
Min Max Min MaxPTFE V-ring –40 450 –40 232
PTFE/composition –100 450 –73 232Packing (temperatures shown are
Graphite ribbon/filament –325 1000(9) –198 538(9)material temperature capabilities)
Graphite ribbon for high-temperatureoxidizing service
700 1200 371 649
Packing flange, studs and nuts whenused with standard bonnet
S31600 –325(1) 1100 –198(1) 593
Packing follower, and packing spring(8) or lantern ring S31600
Packing box ring when used with standard bonnet S31600–325(1) 1100 –198(1) 593
Extension bonnet Trims 1 & 4 S41600 –20 800 –29 427Extension bonnetbushing Other trims S31600 –325(1) 1100 –198(1) 593
1. May be used down to –425�F (–254�C) if manufacturing process includes Charpy impact test.2. This minimum is due to thermal expansion differential between piston ring and cage at low temperatures.3. For high-temperature air, hydrocarbons, and certain other chemicals and solvents, but cannot be used with ammonia, steam, or hot water.4. Has excellent moisture resistance to hot water and steam and may be used with most fire-resistant hydraulic oils, but cannot be used with petroleum-based fluids and otherhydrocarbons.5. Cannot be used with fire-resistant hydraulic oils.6. May be used to increase hot water service capability to 450�F (232�C).7. This material may be used for cyclic temperatures or those above 450�F (232�C).8. Spring is used only with single PTFE V–ring packing; lantern ring replaces spring in other packings.9. Except 700�F (371�C) on oxidizing service.10. If used with PEEK anti-extrusion rings, PTFE/carbon seal ring may be used in temperatures up to 600�F (316�C) for non-oxidizing service or up to 500�F (260�C) for oxidizingservice.11. These materials not limiting factors.
Table 21. Additional Specifications(1)
VALVE STEM AND YOKE BOSS DIAMETERSPORT VALVE
PLUG Standard OptionalVALVE SIZE, INCH DIAMETER PLUG
TRAVEL Stem Yoke Boss Stem Yoke BossCAGE STYLE
Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm4 x 2 2-5/16 59 1-1/8 29 1/2 12.7 2-13/16 71 3/4 19.1 3-9/16 90
3/4 19.1 3-9/16 90
6 x 4, 8 x 4 4-3/8 111 2 51 1/2 12.7 2-13/16 71 1 25.4 Quick-opening, linear,6 x 4, 8 x 4 4-3/8 111 2 51 1/2 12.7 2-13/16 711-1/4 31.8
5 127 equal percentage, WhisperTrim I, or Cavitrol(1)
1 25.4Trim I, or Cavitrol(1)
8 x 6, 12 x 6 7 178 2 51 3/4 19.1 3-9/16 901-1/4 31.8
5 127
1 25.4
8 x 6, 12 x 6 7 1783 76 3/4 19.1 3-9/16 90
1-1/4 31.85 127 Cavitrol only(1)
8 x 6, 12 x 6 7 1784(2) 102(2) 3/4 19.1 3-9/16 90 - - - - - - - - - - - - Whisper Trim I only
8 x 6 5-3/8 136 5(3) 127(3)
12 x 6 5-3/8 136 6-1/2(3) 165(3) 3/4 19.1 3-9/16 90 1 25.4 5 127 Whisper Trim III only
1 25.4 Quick-opening, linear,10 x 8 8 203 3 76 3/4 19.1 3-9/16 901-1/4 31.8
5 127 Quick-opening, linear,equal percentage only
Class 300(4) 1 25.4Class 300(4)
or 600(4)8 203 3 76 3/4 19.1 3-9/16 90
1-1/4 31.85 127
3/4 19.1 3-9/16 90Quick-opening, linear, or
12 x 8 Class 900 8 203 3 761 25.4
5 127 1 25.4equal percentage only
12 x 8 Class 900 8 203 3 761-1/4 31.8
5 1271-1/4 31.8 5H(5) 127H(5)
Class 9007-3/4(6)
or6-3/4(7)
197(6)
or172(7)
6 152 1-1/4 31.8 5 127 - - - Whisper Trim III only
1. Except for Cavitrol III cages, which are covered in separate documentation.2. Bonnet spacer required. This travel available only in Class 300 or 600 Design EWD or EWT valve.3. Bonnet spacer required for Design EWD or EWT valve but not for Design EWS valve.4. Bonnet spacer required for Design EWD, EWS, and EWT valve.5. H indicates heavy actuator-to-bonnet bolting is required.6. Port diameter for level A, B, or C cage.7. Port diameter for level D cage.
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
26
Figure 18. Typical ENVIRO-SEAL and HIGH-SEAL Packing Systems
����������"� &��������'���������!���������(����'���
����������&��������'���������!����� ���������'���
����������"� &��������'���������!����� ���������'���
����������"� &��������'���������!������������'���
SPRING
PACKING
PACKINGBOXSTUD
FOLLOWER
W5801–3 / IL
W5803–3 / IL
SPRINGS
ANTI–EXTRUSIONRING
LANTERNRING
PACKINGBOXSTUDS
PACKINGRING
VALVEBONNET
SPRINGS
FOLLOWER
PACKINGBOXSTUD
PACKING
VALVEBONNET
W5805–5 / IL
A7018 / IL
EW SeriesProduct Bulletin51.1:EWFebruary 2002
27
Table 22. Approximate WeightsVALVE SIZE, INCHES
END CONNECTION 4 x 2 6 x 4 8 x 4 8 x 6 12 x 6 10 x 8 12 x 8END CONNECTIONLb kg Lb kg Lb kg Lb kg Lb kg Lb kg Lb kg
Class 300 185 84 330 150 515 234 625 284 1102 500 1250 567 1440 653
Flanged 220 100 430 195 600 272 680 308 1590 721 1640 744 1890 857Class 600
Buttwelding 135 61 270 122 390 177 600 272 1160 526 1130 512 1450 658
Flanged - - - 1350 612 - - - 3000 1361Class 900
Buttwelding - - - 1000 454 - - - 2850 1293
Figure 19. ENVIRO-SEAL Bellows Seal Bonnet
W5852–1/IL
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
28
Table 23. Bonnet Selection Guidelines
BONNET STYLE PACKINGIN-BODY PROCESS
TEMPERATURE LIMITS(2)(CLASS 300, 600)(1) PACKING
�F �C
Plain Bonnet� Standard for 2-, 4-, and 6-inch
PTFE V-ring 0 to 450 –18 to 232� Standard for 2-, 4-, and 6-inchnominal trim sizes� Standard for 10 x 8 and 12 x 8-inch valves
PTFE/composition 0 to 450 –18 to 232� Standard for 10 x 8 and 12 x 8-inch valves(in cast iron, WCB). Notavailable in S31600
Graphite ribbon/filament 0 to maximum shown in table 20 0 to maximum shown in table 20
Style 1 Cast Extension Bonnet� Optional for 2-, 4-, and 6-inch
PTFE V-ring� Optional for 2-, 4-, and 6-inchnominal trim sizes� Standard for 10 x 8 and 12 x 8 inch
PTFE/composition –50 to 0 and above 450 –46 to 18 and above 232� Standard for 10 x 8 and 12 x 8 inchvalves (in S31600). Optionalin WCB; not available in cast iron
Graphite ribbon/filament
Style 2 Cast Extension Bonnet� Optional for 2-, 4-, and 6-inch
PTFE V-ring� Optional for 2-, 4-, and 6-inchnominal trim sizes� Optional for 10 x 8 and 12 x 8-inch
PTFE/Composition –150 to 0 and above 450 –101 to –18 and above 232� Optional for 10 x 8 and 12 x 8-inchvalves (in WCB). Not available in castiron or S31600
Graphite ribbon/filament
ENVIRO-SEAL bellows seal bonnet�
PTFE For exceptional stem sealing capabilities. See� Optional for 2-, 4-, 6-, and 8-inch nominaltrim sizes. Maximum travel is 2 inches Graphite
Bulletin 59.1:070, ENVIRO-SEAL Bellows Seal Bonnets, forpressure/temperature ratings.
1. For Class 900 valve bodies, only the plain bonnet is available. Contact your Fisher sales office for assistance if application conditions indicate the need for an extension bonnet for aClass 900 valve body.2. These in-body process temperatures assume an outside, ambient temperature of 70�F (21�C). When using any packing at low process temperatures, a cast extension bonnet mayhave to be used to prevent packing damage which could result from the formation of valve stem frost.
Table 24. Bolting Materials and Temperature Limits for Bolting Compliance with NACE Specification MR0175
VALVE BODY
TEMPERATURECAPABILITIESVALVE BODY
MATERIALBOLTING MATERIAL
�F �CMATERIALMin Max Min Max
NACE (non-exposed bolting) (Standard)
Studs Steel SA-193-B7
Nuts Steel SA-194-2H20 450 –7 232
WCBStuds Steel SA-193-B7
Nuts Steel SA-194-2H lubricated450 800 232 427
Studs Steel SA-193-B7 or B8M strain hardened
CF8M Nuts Steel SA-194-2H or 8M–50 450 –46 232
CF8M(316 SST) Studs Steel SA-193-B8M strain hardened or B7
Nuts Steel SA-194-8M lubricated or 2H lubricated450 800 232 427
NACE (exposed bolting) (Optional)No Derating of Valve Required
Studs Steel SA-564-630 (H1150 dbl(2))
Nuts Steel SA-194-2HM–50(1) 450 –46(1) 232
WCB and CF8MStuds Steel SA-564-630 (H1150 dbl(2))
Nuts Steel SA-194-2HM lubricated450 650 232 343
NACE (exposed bolting) (Optional)Requires Derating of Valve(3) When These Body-to-Bonnet Bolting Materials are Used
Studs Steel SA-193-B7M
Nuts Steel SA-194-2HM–50(1) 450 –46(1) 232
WCB and CF8MStuds Steel SA-193-B7M
Nuts Steel SA-194-2HM lubricated450 800 232 427
1. Minimum temperature is –20�F (–29�C) with WCB valve body material.2. Special heat treating required.3. Derating is not required for ANSI Class 300 valves. Derating may be required for valves rated at ANSI Class 600 or 900. Contact your Fisher sales office for assistance in determiningthe derating of valves when these body-to-bonnet bolting materials are used.
Figure 20. Dimensions
AV7029–KA0921–1 / IL
MATCHLINE FORACTUATOR
MATCH LINE FORACTUATOR
15A9682–CA6108–1 / IL
����������)�(���� ���$�(���������*��
��������������(���������*���������������(���������*�
EW SeriesProduct Bulletin51.1:EWFebruary 2002
29
A(1)
VALVE Class, End Connection Style(2) G (MAX)VALVESIZE, Class 300 Class 600 Class 900 Class ClassSIZE,
INCHES RF RTJ RF, BW RTJ RF RTJ BWClass
300, 600Class900
Inch
4 x 26 x 48 x 4
14.5018.6222.38
15.1219.2523.00
15.5020.0024.00
15.6220.1224.12
- - -- - -- - -
- - -- - -- - -
- - -- - -- - -
4.255.316.94
- - -- - -- - -
8 x 68 x 6 w/10’’ Ends
22.3823.75
23.0024.38
24.0024.62
24.1224.75
36.00- - -
36.12- - -
38.25- - -
7.197.19
7.81- - -
12 x 610 x 812 x 8
30.5027.8830.50
31.1228.5031.12
32.2529.6232.25
32.3829.7532.38
- - -- - -
35.50
- - -- - -
35.62
- - -- - -
37.50
10.0010.8114.00
- - -- - -
14.00
mm
4 x 26 x 48 x 4
368473568
384489584
394508610
397511613
- - -- - -- - -
- - -- - -- - -
- - -- - -- - -
108135176
- - -- - -- - -
8 x 68 x 6 w/10’’ Ends
568603
584619
610625
613629
914- - -
917- - -
972- - -
183183
198- - -
12 x 610 x 812 x 8
775708775
791724791
819752819
822756822
- - -- - -902
- - -- - -905
- - -- - -953
254275356
- - -- - -356
1. Per ANSI B16.10 and FCI 65-2 for Class 300 and 600 only.2. End connection style abbreviations: RF - Raised Face, RTJ - Ring Type Joint, BW - Buttwelding.
Figure 20. Dimensions (Continued)
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
30
DIMENSION D FOR ALL VALVE SIZES
STEM DIA
CAGE VALVE 1/2 Inch3/4 Inch (19.1 mm) 1 Inch (25.4 mm) or
1-1/4 Inch (31.8 mm)CAGESTYLE BONNET SIZE,
INCH
1/2 Inch(12.7 mm) Class 900
OnlyAll ExceptClass 900
Class 300& 600
Class900
Inch mm Inch mm Inch mm Inch mm Inch mm
Plain
4 x 26 x 48 x 48 x 612 x 610 x 812 x 8
8.5010.1210.1911.3114.00- - -- - -
216257259287356- - -- - -
- - -- - -- - -
16.12- - -- - -
23.00
- - -- - -- - -409- - -- - -584
8.3810.0010.0611.3114.0014.7516.19
213254256287356375411
- - -11.8111.8813.0615.75- - -- - -
- - -300302332400- - -- - -
- - -- - -- - -
18.25- - -- - -
23.94
- - -- - -- - -464- - -- - -608
All exceptCavitrol III
Style 1extension
4 x 26 x 48 x 48 x 612 x 610 x 812 x 8
12.5014.1214.19- - -- - -- - -- - -
317359360- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
12.6914.3114.3815.5018.1916.5618.00
322363365394462421457
- - -17.0017.0618.2520.9417.6919.12
- - -432433464532449486
- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -Cavitrol III
or WhisperTrim III
Style 2extension
4 x 26 x 48 x 48 x 610 x 812 x 612 x 8
20.3122.1222.19- - -- - -- - -- - -
516562564- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
20.1921.8121.8822.8124.4425.50- - -
513554556579621648- - -
- - -23.4423.50- - -- - -- - -- - -
- - -595597- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
ENVIRO-SEALbellows seal bonnet
4 x 26 x 48 x 410 x 88 x 612 x 612 x 8
17.1222.6922.75- - -- - -- - -- - -
435576578- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
- - -22.6922.7527.6923.9426.62- - -
- - -576578703608676- - -
- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -
Cavitrol III Plain
4 x 26 x 48 x 48 x 6
10 x 8(1)
10 x 8(2)
12 x 612 x 8
9.9413.6213.6915.88- - -- - -
18.88- - -
252346348403- - -- - -480- - -
- - -- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -- - -
9.8113.5013.5615.8814.7520.1218.88- - -
249343344403375511480- - -
- - -15.31- - -- - -
16.7522.06- - -- - -
- - -389- - -- - -425560- - -- - -
- - -- - -- - -- - -- - -- - -- - -- - -
- - -- - -- - -- - -- - -- - -- - -- - -
Whisper Plain8 x 612 x 612 x 8
- - -- - -- - -
- - -- - -- - -
- - -- - -- - -
- - -- - -- - -
15.6919.81- - -
398503- - -
17.4421.56- - -
443548- - -
- - -- - -- - -
- - -- - -- - -
1. One-stage trim.2. Two-stage trim.
EW SeriesProduct Bulletin51.1:EWFebruary 2002
31
EW SeriesProduct Bulletin
51.1:EWFebruary 2002
32
Fisher Marshalltown, Iowa 50158 USACernay 68700 France Sao Paulo 05424 BrazilSingapore 128461
������������������� ���������������������������������������� �������������������������������������������������� ������������ ������������������������������ ������������������� ��������������
������������������������������ �������������������������������������� ��������������������������������������������������������������������������������������� ������� �������������������� ���������
�Fisher Controls International, Inc. 1973, 2002; All Rights Reserved
Emerson Process Management
www.Fisher.com
This product may be covered by one or more of the following patents: 5,129,625; 5,131,666; 5,056,757; 5,230,498; and 5,299,812 or under pending patents.Cavitrol, easy-e, ENVIRO-SEAL, HIGH-SEAL, Whisper Trim, and Fisher are marks owned by Fisher Controls International, Inc., a business of Emerson Process Management. The Emerson logo is a trademark and service mark of Emerson Electric Co. C-seal is a mark owned by Pressure Science, Inc. All other marks are the property of their respective owners.