Download - Fatigue Analysis - Mechanical Engineering
![Page 1: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/1.jpg)
Strain-Life Approach
For Extreme Environments
Fatigue Analysis
![Page 2: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/2.jpg)
Strain-Life ApproachPresented by
Calvin M. Stewart, PhD
MECH 5390-6390
Spring 2021
![Page 3: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/3.jpg)
Outline
• Monotonic Tension
• Strain-Controlled Fatigue
• Cyclic Stress-Strain Behavior
• Strain-Life Approach
• Life Estimation and Transition Life
• Mean Stress
• Advantages and Limitations of Approaches
• Summary
• Questions
![Page 4: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/4.jpg)
Monotonic Tension
![Page 5: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/5.jpg)
Monotonic Tension
• Monotonic tension stress-strain properties are usually reported in handbooks and are used in many specifications.
• Monotonic behavior is obtained from a tension test where a specimen with circular or rectangular cross section within the uniform gage length is subjected to a monotonically increasing tensile force until it fractures.
• They are easy tests to perform and provide information that has become conventionally accepted.
• However, their relation to fatigue behavior may be remote.
![Page 6: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/6.jpg)
Monotonic Tension
• ASTM E8/E8M - Standard Test Methods for Tension Testing of Metallic Materials• Displacement Controlled.
• A Fixed Displacement Rate is applied.
• Used to obtain material characteristics and strengths
• Tensile stress σ slowly increasing P
• Load and deflection are recorded
![Page 7: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/7.jpg)
Monotonic Tension
• Monotonic uniaxial stress-strain behavior can be based on "engineering" stress-strain or "true" stress-strain relationships.
• The difference is in using original versus instantaneous gage section dimensions.
• Engineering Stress and Strain
• True Stress and Strain
0
P
A = 0
0
l l
l
−=
P
A0
l0
l
A
t
i
P
A =
00
lnl
tl
dl l
l l
= =
l0
![Page 8: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/8.jpg)
Monotonic Tension
• For small strains, <2%, • Engineering stress, σ ≈ True stress, σt
• Engineering strain, ε, ≈ True strain, εt.
• No distinction between "engineering" and "true" components is needed for these small strains.
• For larger strains, the differences become appreciable.
![Page 9: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/9.jpg)
Monotonic Tension
Tensile properties of some engineering alloys are also given in Table A.1 and A.2.
Note: Stress-strain behavior of a material can be sensitive to the strain rate, particularly at elevated temperatures
![Page 10: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/10.jpg)
Monotonic Tension
• The subscript f represents fracture. The true fracture strength, σf, can be calculated from Pf/Af but is usually corrected for necking. The Bridgman correction factor is used to compensate for this triaxial state of stress and applies to cylindrical specimens [3]. The corrected true fracture strength, σf is then given by
• R is the radius of curvature of the neck and Dmin is the diameter of the cross section in the thinnest part of the neck.
![Page 11: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/11.jpg)
Monotonic Tension
• Inelastic/plastic strain results in permanent deformation which is not recovered upon unloading.
• The unloading curve is elastic and parallel to the initial elastic loading line.
• Total strain, ε, is
Straine p = +
![Page 12: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/12.jpg)
Monotonic Tension
• For many metals, a plot of true stress versus true plastic strain in log-log coordinates results in a linear curve.
• An example of such a plot is shown for AISI 11V41 steel.
To avoid necking influence, only data between the yield strength and ultimate strength portions of the stress-strain curve are used to generate this plot.
This curve is represented by the power function:
( )n
pK =
![Page 13: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/13.jpg)
Monotonic Tension
• This type of true stress-true strain relationship is often referred to as the Ramberg-Osgood relationship.
• K is the strength coefficient (stress intercept at εp= 1)
• n is the strain hardening exponent (slope of the line).
• The total true strain is given by:
( )n
pK =
1/n
e pE K
= + = +
• Value of n gives a measure of the material’s work hardening behavior.
• K and n for some engineering alloys are also given in Table A.2.
![Page 14: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/14.jpg)
Table A.1
![Page 15: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/15.jpg)
![Page 16: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/16.jpg)
![Page 17: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/17.jpg)
![Page 18: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/18.jpg)
Monotonic Tension
• Key monotonic properties• Modulus of Elasticity, E• Ultimate Tensile Strength, SUT
• Yield Strength, Sy
• corrected true fracture strength, σf
• True fracture strain, εf
• Strength coefficient, K• Strain hardening exponent, n
• We will find fatigue version of some of these monotonic properties, specifically, S’y, σ’f, ε’f,K’, n’, later.
![Page 19: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/19.jpg)
Strain-Controlled Fatigue
![Page 20: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/20.jpg)
Strain-Controlled Fatigue
• In strain-controlled fatigue testing, a constant strain amplitude, εa is applied to the material or component until it has reached failure.
• Attributes:
• Strain amplitude is plotted against cycles to failure (e.g. ε-N diagram)
• Accounts for actual stress-strain response of the material
• Can be extrapolated to multiaxial loading and notched geometries
• Can be combined with creep relations for high temperature analysis
![Page 21: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/21.jpg)
Strain-Controlled Fatigue
• Types of Strain
• Mechanical Strain History• Most widely used
• Thermal Strain History• For non-isothermal fatigue testing
• Plastic Strain History• For isothermal testing
• For test programs involving multiple temperature levels
![Page 22: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/22.jpg)
Strain-Controlled Fatigue
• An important aspect of the fatigue process is plastic deformation.
• Fatigue cracks usually nucleate from plastic straining in localized regions.
• Therefore, cyclic strain-controlled tests can better characterize fatigue behavior of a material than cyclic stress-controlled tests, particularly in the low cycle fatigue region and/or in notched members.
• Strain-controlled fatigue testing has become very common, even though the testing equipment and control are more complicated than the traditional load or stress-controlled testing.
![Page 23: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/23.jpg)
Strain-Controlled Test Methods
• Strain-controlled testing is usually conducted on a servo-controlled closed-loop testing machine.
• A uniform gage section smooth specimen is subjected to axial straining.
• An extensometer is attached to the uniform gage length to control and measure strain over the gage section.
• A standard strain-controlled test consists of constant amplitude completely reversed straining at a constant or nearly constant strain rate.
• The most common strain-time control signals used are triangular (sawtooth) and sinusoidal waveforms.
• Stress response generally changes with continued cycling and is measured with a load cell. Stress and plastic strain variations are usually recorded periodically throughout the test and cycling is continued until fatigue failure occurs.
• ASTM Standard E606: Strain-Controlled Fatigue Testing.
![Page 24: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/24.jpg)
![Page 25: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/25.jpg)
Strain-Controlled Test Methods
• An important consideration in axial fatigue testing is uniformity of stress and strains in the specimen gage section.
• A major source of non-uniformity of gage section stress and strains is a bending moment resulting from specimen misalignment that can significantly shorten the fatigue life. Specimen misalignment can result from:• eccentricity and/or tilt in the load-train components (including load cell, grips,
and load actuator),
• improper specimen gripping,
• lateral movement of the load-train components during the test due to their inadequate stiffness.
Often fatigue tests are operated in pulsating tension (R>0) to mitigate misalignment. (Typically R=0.1)
![Page 26: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/26.jpg)
Strain History Nomenclature• Def’s:
– Strain range
– Strain amplitude
–Mean strain
– Strain ratio
– Amplitude ratio
max min
2a
−=
max min
2m
+=
max min = −
min
max
R
=
m
aA
=
Period
Frequency
1
f =
1f
=
m
min
max
a
a
Stra
in
![Page 27: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/27.jpg)
Cyclic Stress-Strain Curve
![Page 28: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/28.jpg)
Cyclic σ-ε Curve
• The stress-strain behavior obtained from a monotonic test can be quite different from that obtained under cyclic loading.
• This was first observed by Bauschinger (Effect). His experiments indicated the yield strength in tension or compression was reduced after applying a load of the opposite sign that caused inelastic deformation.
• Thus, one single reversal of inelastic strain can change the stress-strain behavior of metals.
![Page 29: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/29.jpg)
![Page 30: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/30.jpg)
0
1
2
3
![Page 31: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/31.jpg)
Cyclic σ-ε Curve
Fatigue failure almost always begins at a local discontinuity
When stress at discontinuity exceeds elastic limit, plastic strain occurs
The figure shows true stress-true strain hysteresis loops of the first five stress reversals
The area within a hysteresis loop is energy dissipated during a cycle (usually in the form of heating). This energy represents the plastic work from the cycle.
Appreciable progressive change in stress-strain behavior during inelastic cycling.
![Page 32: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/32.jpg)
![Page 33: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/33.jpg)
(a) Fully annealed,
showing cyclic
hardening
![Page 34: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/34.jpg)
(c) Cold-worked, showing
cyclic softening
![Page 35: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/35.jpg)
(b) Partially annealed, showing small cyclic hardening and softening
![Page 36: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/36.jpg)
![Page 37: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/37.jpg)
Cyclic Softening
![Page 38: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/38.jpg)
Cyclic σ-ε Curve
• In essence, under strain-control,• Cyclic Hardening –more stress is required each cycle to produce the same
amount of strain
• Cyclic Softening –less stress is needed to produce the same amount of strain
![Page 39: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/39.jpg)
Stabilized Stage III (Unstable)Cyclic Softening
Notice these two are only slightly different
![Page 40: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/40.jpg)
Cyclic σ-ε Curve
• Strain amplitude is held constant throughout the test
• Peak and valley stresses are plotted for each cycle
• Both crack initiation life and fatigue life can be measured
• Strain is later plotted versus fatigue life
![Page 41: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/41.jpg)
Cyclic σ-ε Curve
• After a certain number of cycles, the hysteresis loop of a material can stabilize (i.e. not change significant from cycle to cycle) Typically the hysteresis loop at Nf/2
• This means any further loops are almost identical up to stage III unstable crack propagation
• Total strain range can be decomposed into plastic and elastic components
e p pE
= + = +
![Page 42: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/42.jpg)
Cyclic σ-ε Curve
• Note: Even though true stress and strains are used, no distinction is usually made between the true and the engineering values, because:• the differences between true and engineering values during the tension and
compression parts of the cycle are opposite to each other, and therefore, cancel out,
• strain levels in cyclic loading applications are often small (typically less than 2%), compared to strain levels in monotonic loading.
![Page 43: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/43.jpg)
Cyclic Stress-Strain CurveStabilized Hysteresis Loops
![Page 44: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/44.jpg)
Stabilized Hysteresis Loops
• A family of stabilized hysteresis loops at different strain amplitudes is used to obtain the cyclic stress-strain curve of a material.
• The tips from the family of multiple loops can be connected to form the cyclic stress-strain curve.
• This curve does not contain the monotonic upper and lower yield points.
![Page 45: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/45.jpg)
![Page 46: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/46.jpg)
Stabilized Hysteresis Loops
• Three methods commonly used to obtain the cyclic stress-strain curve are: • the companion test method
• the incremental step test method
• the multiple step test method
• Even though some differences exist between the results from the three methods, they are small in most cases.
![Page 47: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/47.jpg)
Stabilized Hysteresis Loops
• Companion Test Method – a series of companion samples are tested at various strain levels until the hysteresis loops stabilize. Half-life or near half-life hysteresis loops from each specimen and strain amplitude are used to obtain the cyclic stress-strain curve.
• Incremental Step Test Method – a single specimen is subjected to a series of blocks of gradually increasing and decreasing strain amplitudes. After the material has stabilized (usually after several strain blocks), the hysteresis loops from half a stable block ar then used to obtain the cyclic stress-strain curve.
( ) ( )1 2
...
( )f t =
![Page 48: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/48.jpg)
Incremental Step Test Method
![Page 49: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/49.jpg)
Stabilized Hysteresis Loops
• Multiple Step Test Method - It is similar to the incremental step test method, except rather than incrementally increasing and decreasing strain in each block the strain amplitude is kept constant.
• Once cyclic stability is reached at the constant strain amplitude, the stable hysteresis loop is recorded, and strain amplitude is increased to a higher level.
• This process is repeated until enough stable hysteresis loops are recorded to construct the cyclic stress-stain curve.
![Page 50: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/50.jpg)
Strain History of Multiple Step Test Method
![Page 51: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/51.jpg)
Tension, Compression, and Cyclic Stress-Strain Response
![Page 52: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/52.jpg)
➢ Cyclic Softening
➢ Cyclic Hardening
➢ Cyclically stable
➢ Mixed Hardening
![Page 53: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/53.jpg)
cyclic stress-strain curve of some engineering alloys
![Page 54: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/54.jpg)
Stabilized Hysteresis Loops
• Soft materials will harden
• Material will cyclically harden if
• Dislocation density is initially low and increases rapidly
• Hard materials will soften
• Material will cyclically soften if
• Dislocations rearrange and offer less resistance to deformation
1.4u
y
S
1.2u
y
S
![Page 55: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/55.jpg)
Stabilized Hysteresis Loops: Temperature
![Page 56: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/56.jpg)
Stabilized Hysteresis Loops: Rate Effects
![Page 57: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/57.jpg)
Stabilized Hysteresis Loops
• Similar to monotonic tension, a plot of true stress amplitude, σa, versus true plastic strain amplitude, Δεp/2, in log-log coordinates for is represented by the power function:
• The cyclic stress-strain curve is represented by a Ramberg-Osgoodrelationship as follows:
2
n
p
a K
=
K’ - Cyclic strength coefficientn’ - Cyclic strain hardening exponent. Usually between 0.10 and 0.25.
11
2 2 2 2 2
nnpe a a
aE K E K
= = + = + = +
![Page 58: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/58.jpg)
Stabilized Hysteresis Loops
• Massing’s hypothesis states that the stabilized hysteresis loop branch may be obtained by doubling the basic material stress-strain curve.
• The equation for the stabilized hysteresis loop is written as follows:
1
22
n
E K
= +
![Page 59: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/59.jpg)
1
22
n
E K
= +
1
22
n
E K
= +
1
22
n
e pE K
= + = +
![Page 60: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/60.jpg)
Stabilized Hysteresis Loops
• The cyclic yield strength, Sy′, is defined at 0.2% strain offset which corresponds to a plastic strain of 0.002 on the cyclic stress-strain curve. It can be estimated by substituting Δεp/2 = 0.002 into
• Values of K’ and n’ for selected engineering alloys are given in Table A.2.
2
n
p
a K
=
( )' 0.002n
yS K
=
![Page 61: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/61.jpg)
Cyclic Stress-Strain CurveExample
![Page 62: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/62.jpg)
Example
• Given the results of a companion test series for an engineering alloy find
(a) the true stress amplitude versus true plastic strain amplitude plot
(b) the Ramberg-Osgood relationship to obtain the cyclic stress-strain curve
(c) What type of hardening behavior is observed?
![Page 63: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/63.jpg)
![Page 64: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/64.jpg)
![Page 65: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/65.jpg)
Log-Log true stress amplitude versus true plastic strain amplitude plot
![Page 66: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/66.jpg)
Linear-Linear true stress amplitude versus true plastic strain amplitude plot
![Page 67: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/67.jpg)
Mixed Behavior Observed
![Page 68: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/68.jpg)
Strain-Life Approach
![Page 69: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/69.jpg)
Strain-Life Approach
• The strain-based approach to fatigue problems:• is widely used at present.• Strain can be directly measured.• Application of this approach is common in notched member fatigue.
• Strain-life design method is based on relating the fatigue life of notched parts to the life of small unnotched specimens cycled to the same strains as the material at the notch root.• Since fatigue damage is assessed directly in terms of local strain, this approach is also
called local strain approach.• Expected fatigue life can be determined knowing the strain-time history at the notch
root and smooth strain-life fatigue properties of the material.• The remaining fatigue crack growth life of a component can be analyzed using
fracture mechanics concepts (Ch 6).
![Page 70: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/70.jpg)
Strain-Life Approach
![Page 71: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/71.jpg)
Strain-Life Approach
• Steady-state hysteresis loops can be reduced to elastic and plastic strain ranges or amplitudes.
• Cycles to failure can involve from about 10 to 107cycles and frequencies can range from about 0.1 to 10 Hz.
• Beyond 106 cycles, load or stress-controlled tests at higher frequencies can often be performed because of the small plastic strains and the greater time to failure.
• The strain-life curves are often called low cycle fatigue data because much of the data are for less than 105 cycles.
![Page 72: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/72.jpg)
Strain-Life Approach
• Failure criteria include • the life to a small detectable crack,
• life to a certain percentage decrease in load amplitude (50% drop level is recommended by the ASTM standard E606),
• life to a certain decrease in the ratio of unloading to loading moduli, or
• life to fracture.
• Strain-life fatigue curves plotted on log-log scales are shown schematically in Fig. 5.11.
![Page 73: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/73.jpg)
Material Constants
• The total strain amplitude can be resolved into elastic and plastic strain components from the steady-state hysteresis loops.
• Both the elastic and plastic curves can be approximated as straight lines.
• At large strains or short lives, the plastic strain component is predominant, and at small strains or longer lives the elastic strain component
![Page 74: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/74.jpg)
Modeling the Strain-Life (ε-N) Curve
• Elastic - Basquin (1910)
• Plastic - Coffin-Manson (1954,53)
• The intercepts of the two straight lines at 2Nf= 1 are σf’/E for the elastic component and εf’ for the plastic component.
( )22
bfel
fNE
=
( )22
cpl
f fN
=
![Page 75: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/75.jpg)
Relation of Fatigue Life to Strain
• Applying the equations, the total-strain amplitude is
• Known as Manson-Coffin relationship between fatigue life and total strain
• Some values of coefficients and exponents given in Tables
• Equation has limited use for design since values for total strain at discontinuities are not readily available
( ) ( )2 22 2 2
b cpl fel
a f f fN NE
= = + = +
![Page 76: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/76.jpg)
Modeling the Strain-Life (ε-N) Curve
• Nomenclature
![Page 77: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/77.jpg)
Relation of Fatigue Life to Strain
• Basquin’s Law [1910]
• Fatigue strength coefficient, 'F is approximately equal to the true fracture strength at fracture, F (in MPa or ksi)
• Fatigue strength exponent, b is the slope of the elastic-strain line, and is the power to which the life 2N must be raised to be proportional to the true-stress amplitude. Ranges between 0.05 to -0.12
![Page 78: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/78.jpg)
Relation of Fatigue Life to Strain
• Coffin-Manson Law [1954, 1953]
• Fatigue ductility coefficient, 'Fis approximately equal to te true fracture ductility, F
• Fatigue ductility exponent, c is the slope of plastic-strain line, and is the power to which the life 2N must be raised to be proportional to the true plastic-strain amplitude. Ranges from -0.5 to -0.7
![Page 79: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/79.jpg)
Strain-Life Approach
Typical Complete Strain-life Curve With Data Points For Annealed 4340 Steel
Fatigue life can be plotted as cycles or reversals
Data plotted on semi-log or log-log
Data includes a bend.
![Page 80: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/80.jpg)
Elastic Line
![Page 81: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/81.jpg)
Plastic Line
![Page 82: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/82.jpg)
Definition of the Strain-Life Curve
• Def: Transition Life, Nt – point at which elastic and plastic contributions to the life are equal.
• For lives <2Nt, the deformation is mainly plastic,
• For lives >2Nt, the deformation is mainly elastic.
( )1
2
b c
f
t
f
EN
−
=
![Page 83: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/83.jpg)
Strain-Life Curves: Different Materials• Many materials have similar life at
a total strain amplitude of about 0.01.
• At larger strains, increased life is dependent more on ductility, while at smaller strains longer life is obtained from higher strength materials.
• The optimum overall strain-life behavior is for tough metals, which are materials with good combinations of strength and ductility.
![Page 84: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/84.jpg)
Monotonic Tension Test
• Strain Energy• Resilience is the elastic energy
absorbed by the specimen and is equal to the area under the elastic portion of the stress-strain curve.
• Tensile toughness is the total energy density or energy per unit volume absorbed during deformation (up to fracture) and is equal to the total area under the engineering stress-strain curve
( )2
2
ys
RUE
=
U d =
![Page 85: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/85.jpg)
Strain-Life Curves: Thermomechanical Processing
Medium Carbon Steel in quenched and normalized condition
![Page 86: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/86.jpg)
Strain-Life Curves: Ni Alloys
![Page 87: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/87.jpg)
Strain-Life Curves: Al Alloys
![Page 88: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/88.jpg)
Strain-Life Approach
• Strain-life fatigue data for selected engineering alloys are included in Table A.2.
• These properties are obtained from small, polished, unnotched axial fatigue specimens under constant amplitude fully reversed cycles of strain.
• Material properties in Table A.2 also omit influences of surface finish, size, stress concentration, temperature, and corrosion.
![Page 89: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/89.jpg)
![Page 90: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/90.jpg)
![Page 91: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/91.jpg)
Table of Strain-Life Properties
![Page 92: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/92.jpg)
Table of Strain-Life Properties
Shigley’s Mechanical Design
![Page 93: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/93.jpg)
Strain-Life ApproachExample
![Page 94: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/94.jpg)
![Page 95: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/95.jpg)
![Page 96: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/96.jpg)
![Page 97: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/97.jpg)
![Page 98: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/98.jpg)
Solving Problems
![Page 99: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/99.jpg)
Plots
![Page 100: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/100.jpg)
Plots
• stabilized hysteresis loop
1
22
n
E K
= +
![Page 101: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/101.jpg)
Equations
![Page 102: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/102.jpg)
Properties
• The fatigue strength coefficient, σ’f and fatigue strength exponent, b, are the intercept and slope of the linear least squares fit to stress amplitude, Δσ/2, versus reversals to failure, 2Nf, using a log-log scale
• Similarly, the fatigue ductility coefficient, ε’f, and fatigue ductility exponent, c, are the intercept and slope of the linear least squares fit to plastic strain amplitude,Δεp/2, versus reversals to failure, 2Nf, using a log-log scale.
![Page 103: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/103.jpg)
Strain-Life Properties
• Plastic strain amplitudes can either be measured directly from half of the width of stable hysteresis loops at σ = 0 or calculated from
• A difference usually exists between the measured and calculated values, which results from the difference between monotonic and cyclic moduli of elasticity and rounding of the hysteresis loops near the strain axis.
![Page 104: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/104.jpg)
Strain-Life Properties
Fatigue Strength Coefficient, σf′
σf′ ≈ σf
where σf is the true fracture strength measured from a monotonic tensile tests
Note: For steels with BHN<500: σf =Su+50ksi
Fatigue Strength Exponent, b
-0.13 < b < -0.05
Fatigue Ductility Coefficient, εf′
εf′ ≈ εf
Note:
Fatigue Ductility Exponent, c
-1.0 < c < -0.5
1ln
1f
RA
=
−
![Page 105: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/105.jpg)
Strain-Life Properties
2 1
510 0.25
P Pb
−=
−
4 3
410 10
P Pc
−=
−
![Page 106: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/106.jpg)
Cyclic hardening exponent, n’
Cyclic hardening coefficient, K’
Strain-Life to Cyclic Properties
• The cyclic strength coefficient, K’, and cyclic strain hardening exponent, n’, are obtained from fitting stable stress amplitude versus plastic strain amplitude data.
• Rough estimates of K’ and n’ can also be calculated from the low cycle fatigue properties by using:
Fatigue strength exponent, b
Fatigue ductility exponent, c
bn
c =
( )f
n
f
K
=
( )1 5
nb
n
−=
+
( )
1
1 5c
n
−=
+
![Page 107: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/107.jpg)
Monotonic Approximation
![Page 108: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/108.jpg)
Textbook
• When the subject material is known, use Table A2 to obtain monotonic, cyclic, and strain-life properties.
![Page 109: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/109.jpg)
On Failure,
• Note that life to failure may be defined in several ways. These Include:
• Separation of specimen
• Development of a given crack length (often 1mm)
• Loss of specified load carrying capability (often 10 or 50% load drop)
• Specimen separation in the most common failure criteria for uniaxial loading. However, in many cases, there is not a large difference between these criteria.
![Page 110: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/110.jpg)
Be Careful…
• Cycles versus Reversals. The strain-life approach measures life in terms of reversals (2N), whereas the stress-life method uses cycles (N). A reversal is one-half of a full cycle.
• Amplitude versus range. The strain-life approach uses both strain range, ∆ε and amplitude, εa which differ by a factor of 2.
• Cyclic σ-ε curve versus hysteresis curve. Massing’s hypothesis states that the hysteresis curve can be modeled as twice the cyclic stress strain curve.
• In essence, Find Nf !!! Not 2Nf !!!
2a =
![Page 111: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/111.jpg)
Mean Stress
![Page 112: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/112.jpg)
Mean Stress
Increase life
Decrease life
![Page 113: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/113.jpg)
![Page 114: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/114.jpg)
Mean Stress: SAE 1045 Hardened Steel
![Page 115: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/115.jpg)
Mean Stress: Relaxation
• Mean stress tends toward zero for large plastic strain amplitudes
• This is true for cases having either compressive or tensile mean stress
• Note this is not cyclic softening.
• Mean stress relaxation can occur in materials that are cyclically stable.
![Page 116: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/116.jpg)
Morrow’s Mean Stress Correction
• Morrow’s Mean Stress Correction
• The predictions made with Morrow’s mean stress correction model are consistent with the observations that mean stress effects are significant at low values of plastic strain, where the elastic strain dominates.
• This relation incorrectly predicts that the ratio of elastic to plastic strain range is dependent on mean stress.
• Predictions for compressive mean stress cases can be inaccurate.
( ) ( )2 22
b cf m
a f f fN NE
− = = +
![Page 117: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/117.jpg)
Mean Stress Correction
( )1
2
b c
f
t
f m
EN
−
= −
![Page 118: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/118.jpg)
Manson and Halford Model
• Manson and Halford Model [1981]
• here both the elastic and plastic terms are affected by the mean stress is given by
• This equation tends to predict too much mean stress effect at short lives or where plastic strains dominate. At high plastic strains, mean stress relaxation occurs.
![Page 119: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/119.jpg)
Manson and Halford Model
In Manson-Halford, Both the elastic and plastic portion of the Strain-life Curve are modified by the mean stress.
![Page 120: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/120.jpg)
Smith, Watson, and Topper Model
• Smith, Watson, and Topper Model [1970]
This equation assumes that for different combinations of strain amplitude, εa, and mean stress, σm, the product σmax εa
remains constant for a given life.
If σmax is zero, this Eq. predicts infinite life, which implies that tension must be present for fatigue fractures to occur.
The SWT Eq. has been shown to correlate mean stress data better for a wide range of materials and is regarded to be more promising for general use.
![Page 121: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/121.jpg)
Smith, Watson, and Topper Model
![Page 122: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/122.jpg)
![Page 123: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/123.jpg)
Fatigue Design Considerations
• In many design situations transient material behavior can be critical and must be considered during material selection
• Ductility useful for LCF conditions (Ex: annealed 4340 steel)
• High strength for HCF conditions (Ex: maragning steel)
• If mechanical loading is very different from benchmark conditions, then conduct additional LCF experiments
![Page 124: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/124.jpg)
Comparison of Stress-Life and Strain-Life
Advantages of Stress-Life
• Empirical parameters for a lot of materials has been determined• Marin factors• Fatigue Strengths
• Easy to use for design applications
• Back of the envelope calculations allow good accuracy
• Works well for long life components
Disadvantages for Stress-Life
• Cannot be used for LCF conditions
• If loads are fluctuating in a pseudo-random way, stress-life can yield non-conservative results
• Mostly empirical
Advantages of Strain-Life
• Takes into account actual stress-strain response of material during cycling.
• More conservative of the two approaches
• Widely used in industry
• Accurately predicts crack initiation stage
• Closer connection to physical nature of material
• Distinguishes between initiation and propagation
Disadvantages for Strain-Life
• Analysis depends on testing, strain data must be available
• Analysis is more complicated
• Less data is available
![Page 125: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/125.jpg)
Stages of Component Fatigue
• Force-controlled and strain-controlled fatigue are relevant to crack initiation and early propagation
• LEFM Methods are appropriate otherwise
![Page 126: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/126.jpg)
Summary
➢Basic material mechanical properties such as strength and ductility can be obtained from simple monotonic tensile tests. However, The stress-strain behavior obtained from simple monotonic tensile tests can be quite different from that obtained under cyclic loading.
➢Cyclic loading can cause hardening and/or softening of the material. Using a monotonic stress-strain curve of a cyclic softening material in a cyclic loading application can significantly underestimate the extent of plastic deformation present.
➢Changes in cyclic deformation behavior are more pronounced at the beginning of cyclic loading, as the material usually gradually stabilizes with continued cycling.
![Page 127: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/127.jpg)
Summary
➢stable cyclic stress-strain curve can be represented by the following equation for many metals:
➢where K’ and n’ are material cyclic deformation properties.
➢Fatigue cracks usually nucleate from plastic straining in localized regions. Strain-based approach to fatigue problems is widely used at present.
11
2 2 2 2 2
nnpe a a
aE K E K
= = + = + = +
![Page 128: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/128.jpg)
Summary
➢The strain-life equation is expressed as:
➢The Strain-life approach is a comprehensive approach which can be applied for the treatment of both low cycle and high cycle fatigue.
➢In the low cycle region plastic strain is dominant, whereas in the high cycle region elastic strain is dominant.
( ) ( )2 22 2 2
b cpl fel
a f f fN NE
= = + = +
![Page 129: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/129.jpg)
Summary
➢At large strains better fatigue resistance depends more on ductility, while at small strains it depends more on strength.
➢Strain-controlled cycling with a mean strain results in a mean stress that usually relaxes at large strain amplitudes due to the presence of plastic deformation.
➢A non-relaxing mean stress can significantly affect the fatigue life with tensile mean stress having detrimental effect and compressive mean stress having beneficial effect.
➢Other synergistic effects of loading, environment, and component or material processing can also influence the strain-life behavior.
![Page 130: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/130.jpg)
Homework 5
• Problem 5.3 from the text.
• Problem 5.5 from the text.
• Problem 5.7 from the text.
• Problem 5.8 from the text.
• Problem 5.12 from the text.
• Problem 5.19 from the text.
![Page 131: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/131.jpg)
References
• Stephens, R.I., Fatemi, A., Stephens, R.R., Fuchs, H.O., 2000, Metal Fatigue in Engineering 2nd Edition, Wiley.
• Suresh, S., 1998, Fatigue of Materials 2nd Edition, Cambridge University Press.
• Bannantine, J., 1989, Fundamentals of Metal Fatigue Analysis, Pearson.
• Schijve, J., 2008, Fatigue of Structure and Materials 2nd Edition, Springer.
• Shigley’s Mechanical Design
![Page 132: Fatigue Analysis - Mechanical Engineering](https://reader031.vdocument.in/reader031/viewer/2022012420/61748b9f34a1aa7b2a2ccbe9/html5/thumbnails/132.jpg)
CONTACT INFORMATION
Calvin M. Stewart
Associate Professor
Department of Mechanical Engineering
The University of Texas at El Paso
500 W. University Ave, Suite A126, El Paso, TX 79968-0521
Ph: 915-747-6179
me.utep.edu/cmstewart/