Download - Fluid Power Energy, Inc
![Page 1: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/1.jpg)
Oil Cleaning Centrifuge
![Page 2: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/2.jpg)
What is Spin-Clean?
A true centrifuge that, when sized properly, will remove the dense wear abrasives from oil down to below 1 micron
Will not use more than 10% of engine oil pump output at any given time
The centrifuge removes the solids from the engine oil using centrifugal force – 1000 G’s
Significantly reduces engine wear, sludge build-up, & acid formation
![Page 3: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/3.jpg)
How it worksPressurized oil enters Spin-Clean on bottom right. (Inlet)
Oil enters into turbine, begins to fill, and pressurizes.
Oil exits out of the two nozzles at the bottom of the turbine at a very high velocity, thus causing the turbine to spin.
As the oil exits the shaft in the turbine bowl the solid particles are whipped against the inner wall of the bowl at a high rate of speed.
Solid particles down to below 1 micron are captured on the inside wall of the turbine bowl creating a dense cake-like solid.
Clean oil exits the centrifuge into the engine sump.
![Page 4: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/4.jpg)
Why Spin-Clean?
Engine manufactures install full-flow filters that only remove particles from the oil down to 20-25 micron
Increase the interval between oil/filter changes
Significantly increase engine lifeGo Green – better for the environmentServes as a diagnostic tool
![Page 5: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/5.jpg)
Spin-Clean waste
Actual Spin-Clean bowl after 2000 hours
“Cake” accumulates on inner wall of turbine bowl
Easy to clean – minimal down time
![Page 6: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/6.jpg)
More Examples
Lapping Oil Engine Oil
![Page 7: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/7.jpg)
Additional BenefitsAids in detecting excessive wear problemsAids in the detection of coolant leaksImproves engine up timeReduces hazardous waste feesWill not remove oil additives or
conditionersCentrifuge can be cleaned while the engine
is runningEasily installed
![Page 8: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/8.jpg)
Target MarketsOil & Gas – Exploration, Refineries,
Production, Gathering Pipelines, & Service Companies
Marine Ships – 500 (and up) Gross Registered Tonnage (GRT)
Marine – Less Than 500 GRT – Inland Waterways & Offshore
Drilling – Land and OffshoreIndustrial Markets – Extrusion, Stamping,
Foundry, Hydraulic
![Page 9: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/9.jpg)
Target Markets Cont…
Railroad & Maintenance of WayConstruction and MiningCogeneration and Peak ElectricGovernment Including MilitaryOEM Original Equipment Manufacturers and
Equipment Packagers
![Page 10: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/10.jpg)
FPE Spin-Clean Model 7575-1 Model Also
Available – Cut Out Valve Assembly
Rated at 1 Gallon Per Minute (3.7 L/min)
Oil Sump Capacity – Up to 15 Gallons (56.8 L)
Dirt Holding Capacity – 18 in3 (278 cm3)
![Page 11: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/11.jpg)
FPE Spin-Clean Model 150
Rated at 2 Gallons Per Minute (7.6 L/min)
Oil Sump Capacity – Up to 30 Gallons (113.5 L)
Dirt Holding Capacity – 53 in3 (828 cm3)
![Page 12: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/12.jpg)
FPE Spin-Clean Model M300
Rated at 4 Gallons Per Minute (15 L/min)
Oil Sump Capacity – Up to 60 Gallons (227 L)
Side DrainDirt Holding Capacity
– 150 in3 (2340 cm3)
![Page 13: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/13.jpg)
FPE Spin-Clean Model 300Rated at 4 Gallons Per
Minute (15 L/min)Oil Sump Capacity – Up
to 60 Gallons (227 L)Oil Control Base Option
Available (OCB)Bottom DrainDirt Holding Capacity –
150 in3 (2340 cm3)
![Page 14: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/14.jpg)
FPE Spin-Clean Model 1000Available in 8, 12, &
16 Gallons Per Minute (30, 45, & 60 L/min)
Oil Sump Capacity – Up to 120, 180, or 240 Gallons (454, 681, 908 L)
Oil Control Base Option available (OCB)
Dirt Holding Capacity – 350 in3 (5462 cm3)
![Page 15: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/15.jpg)
What to Know When Sizing a Spin-Clean
Engine Make, and Model
Oil Sump Capacity (Gallons)
Oil Pump Output (GPM) @ what RPM
![Page 16: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/16.jpg)
How to Size a Centrifuge -Sizing Chart
![Page 17: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/17.jpg)
Sizing NotesSpin-Clean uses 10% of the oil sump capacity at
any given time.The volume of oil in the system may be used to
determine the type and number of centrifuges to be fitted.
A centrifuge should be specified to ensure that the total crankcase oil capacity passes through the centrifuge(s), no less than four times in an hour.
The optimum oil inlet pressure for a centrifuge ranges from 60 to 80 psi, but units can be operated at a maximum of 100 psi or a minimum of 30 psi.
![Page 18: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/18.jpg)
Sizing Example
![Page 19: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/19.jpg)
Spin-Clean sizing information and sizing calculator now available on Fluid Power Energy’s new website
www.fpevalves.com
Spin-Clean / engine manufacture match-up documentation available
upon request
![Page 20: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/20.jpg)
InstallationDue to different field applications, different
engine sizes, and other unforeseen circumstances we offer several installation options. All originate from these two methods.
-Gravity drain Spin-Clean is mounted higher than the crankcase –
Gravity forces oil to drain from Spin-Clean down to engine crankcase.
-Oil Control Base (OCB) This option is used if the Spin-Clean is mounted below
the engine crankcase. Compressed air (.02 SCFM) is used to pressurize the Spin-Clean unit sending oil back up to the crankcase.
![Page 21: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/21.jpg)
Gravity Drain Installation
![Page 22: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/22.jpg)
Gravity Drain Installation -M300 Side Drain
![Page 23: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/23.jpg)
Gravity Drain Installation-Model 75 Side Drain
![Page 24: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/24.jpg)
OCB Installation -Model 1000 (drain up to crankcase)
![Page 25: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/25.jpg)
Installation KitsOur goal is to make Spin-Clean installation
easy. Let us provide you with the accessories you’ll need to just hookup and go. (Reduced downtime!)
Kits available or most engine makes and models such as: Caterpillar, Waukesha, Cummins & Superior
If we don’t have a kit for your engine/application we’ll make one!
![Page 26: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/26.jpg)
Installation KitsCAT 3600
Series Engine -Model 1000
Spin-Clean
Includes:Fittings/valvesHosesGravity baseCrankcase doorDoor seal
![Page 27: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/27.jpg)
Installation KitsWaukesha VHP
Series Engine -Model 1000
Spin-Clean
Includes:Fittings/valvesStainless Steel
tubing (optional)
Gravity baseCrankcase doorDoor seal
![Page 28: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/28.jpg)
Installation KitsWaukesha
7042 Engine -Model M300
Spin-Clean
Includes:Fittings/valvesHosesDoor AssemblyDoor Seal
![Page 29: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/29.jpg)
Field Applications
![Page 30: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/30.jpg)
Yi-Chang Diesel
-Gravity Drain
![Page 31: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/31.jpg)
White Superior -16 Cylinder
-Model 1000OCB -Oil Control Base
![Page 32: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/32.jpg)
Sulzar 16-ZAV
-Multiple Spin- Clean Installation
![Page 33: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/33.jpg)
Caterpillar 3608
-Model 1000OCB -Oil Control Base
![Page 34: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/34.jpg)
Caterpillar 3412
-Model M300 -Bottom Drain
![Page 35: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/35.jpg)
Caterpillar G3516
-Model M300 -Side Drain
![Page 36: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/36.jpg)
Spin-Clean Testing
Several test programs available
Oil analysis availableSpectrometric and Particle testing
Spin-Clean bowl waste analyzing
![Page 37: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/37.jpg)
Success storiesCanada Oil & Gas Production
Waukesha 7042 Engine 47% Cleaner lube oil 20 Gal reduction in oil consumption Doubled Full-Flow Filter life
Oil & Gas Drilling RigCaterpillar D399 Engine
Increased Oil Service by 50%
![Page 38: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/38.jpg)
Spin-Clean Test – Phase 1Change oil and full-flow filter elements.Pull sample of new oil – Tag as “Sample # 1” - Log
total engine hours. Mail used oil “Sample #1” to FPE.Run 30 days and Pull oil sample – Tag as “Sample #2”
– Log total engine hours. Mail used oil “Sample #2 to FPE
Run 30 days and Pull oil sample – Tag as “Sample #3” – Log total engine hours. Mail used oil “Sample #3” to FPE.
Run 30 days and Pull oil sample – Tag as “Sample #4” – Log total engine hours. Mail used oil “Sample #4” to FPE.
Develop baseline from the above oil sample test reports.
![Page 39: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/39.jpg)
Spin-Clean Test – Phase 2 Change oil and full-flow filter elements.Pull sample of the new oil – Tag as “Sample # 5” – Log
total engine hours. Mail new oil “Sample #5” to FPE.Run 30 days and Pull oil sample – Tag as “Sample #6” –
Log total engine hours. Mail used oil “Sample #6” to FPE.Run 30 days and Pull oil sample – Tag as “Sample #7” –
Log total engine hours. Mail used oil “Sample #7” to FPE.Run 30 days and Pull oil sample – Tag as “Sample #8” –
Log total engine hours. Mail used oil “Sample #8” to FPE.Collect solids from centrifuge, weigh solids and
photograph solids.Mail dirt sample with used oil “Sample #8” to FPE
![Page 40: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/40.jpg)
New Applications for Spin-CleanUnits for oil reclamation
Stationary, skid mounted, initial unit on site trial 2-10-10
Trailer mountedWith or without tankCompressor maintenance facilitiesTruck & Bus fleet facilitiesHydraulic/industrialAny application where you need to remove solids
Special version for Screw Compressors
![Page 41: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/41.jpg)
Stationary UnitModel 1000 with 150 gallon tank
![Page 42: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/42.jpg)
![Page 43: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/43.jpg)
OIL RECLAMATION SYSTEM
Significantly reduce annual oil expenses! Protect your equipment from harmful particles/sludge! Positively impact the environment! Fluid Power Energy has developed a product to help you do all three. Our new Oil Reclamation System allows you to clean up to 150 gallons of dirty oil by removing harmful particulate matter.
4 Micron 6 Micron 10 Micron
Above data is based on a 48 hour test of 15w40 diesel oil. Oil cleanliness is based on third-party oil sampling - additive package or clean oil may have to be added to reclaimed oil to be deemed as suitable for reuse.
![Page 44: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/44.jpg)
Screw Compressor Unit
![Page 45: Fluid Power Energy, Inc](https://reader035.vdocument.in/reader035/viewer/2022062314/56813a4a550346895da24071/html5/thumbnails/45.jpg)