-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
1/74
OPERATION MANUAL
MODE DEMPLOIMANUAL DE OPERACIONMANUAL DE OPERAO
XV-Z200U
PROJECTOR
PROJECTEURPROYECTORPROJETOR
ENGLISH ............. -1 -72
FRANAIS ........... -1 -71
ESPAOL ............ -1 -70
PORTUGUS ...... -1 -70
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
2/74
Introducti
on
-1
Before using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP Projector, usingthe REGISTRATION CARD packed with the projector.
1. WARRANTYThis is to assure that you immediately receive the full benefit of the parts, service and laborwarranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACTTo ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASEREAD CAREFULLY THE IMPORTANT LIMITED WARRANTY CLAUSE.
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especiallycareful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product torain or moisture.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment notexpressly approved by the manufacturer could void the users authority to operate this equip-ment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended toalert the user to the presence of uninsulateddangerous voltage within the productsenclosure that may be of sufficient magnitudeto constitute a risk or electric shock topersons.
The exclamation point within a triangle isintended to alert the user to the presence ofimportant operating and maintenance(servicing) instructions in the literatureaccompanying the product.
Introduction ENGLISH
CAUTIONRISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS.
See bottom of actual set.
U.S.A. ONLY
U.S.A. ONLY
IMPORTANTFor your assistance in reporting the loss or theft of yourProjector, please record the Serial Number located on
the bottom of the projector and retain this information.Before recycling the packaging, please be sure thatyou have checked the contents of the carton thoroughlyagainst the list of Supplied accessories on page 12.
Model No.: XV-Z200U
Serial No.:
PRODUCT DISPOSALThis product utilizes tin-lead solder, and high intensity discharge lamp (HID lamp) containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling
information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org .
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
3/74-2
WARNING:The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.During normal operation, when putting the projector into the standby mode always use the STANDBY button on theprojector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
INFORMATIONThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the operation manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. U.S.A. ONLY
Declaration of ConformitySHARP PROJECTOR, MODEL XV-Z200U
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430
TEL: 1-800-BE-SHARP (1-800-237-4277) U.S.A. ONLY
WARNING:Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments.
Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile
the contents thereof.
LAMP REPLACEMENT
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFOREREPLACING THE LAMP. REPLACE WITH SAME SHARP LAMPUNIT TYPE BQC-XVZ200++1 ONLY. UV RADIATION : CAN CAUSEEYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.HIGH PRESSURE LAMP : RISK OF EXPLOSION.POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HASRUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
DU REMPLACEMENT DE LA LAMPE.PRECAUTIONS A OBSERVER LORS
DEBRANCHER LE CORDON DALIMENTATION AVANT DE RETIRER LES VIS.LINTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE1 HEURE AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-XVZ200++1.RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.ETEINDRE LA LAMPE AVANT DE PROCEDER A LENTRETIEN.LAMPE A HAUTE PRESSION : RISQUE DEXPLOSION.DANGER POTENTIEL DE PARTICULES DE VERRE EN CAS DECLATEMENT DE LA LAMPE.A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE DEMPLOI.
CAUTION
Caution Concerning the Lamp Replacement
There is potential glass particles hazard if the lamp ruptures.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
4/74
Introducti
on
-3
Contents
IntroductionContents............................................................... 3
IMPORTANT SAFEGUARDS ............................... 4
Quick Guide ......................................................... 7
Part Names .......................................................... 8Operating the Remote Control ......................... 11
Accessories ....................................................... 12
Connections & SetupConnecting the Projector to Other Devices.... 14
Connecting the Power Cord ................................... 14
Connecting to Video Equipment .......................... 15
Connecting to a DVD Player and DTV Decoder ..... 17
Connecting to a Computer .................................. 21
Controlling the Projector by a Computer ............. 23
Setup .................................................................. 24Using the Swivel Stand ............................................24
Removing the Swivel Stand .....................................24
Attaching the Swivel Stand..................................... 25
Focusing and Zooming ...........................................25
Using the Lens Shift ................................................25
Adjusting the Projection Distance .......................... 26
Image Projection......................................................28
Basic OperationImage Projection ............................................... 30
Basic Procedure ......................................................30Selecting the On-screen Display Language ...........31
Turning the Power off .............................................. 32
Keystone Correction ................................................33
Placement of the Projected Image
Using the Keystone Correction............................34
Freezing a Moving Image....................................... 35
Adjusting the Picture Aspect Ratio ..........................35
Adjustments and SettingsUsing the Menu Screen .................................... 38
Menu Selections (Adjustment) ................................38Menu Selections (Settings) ..................................... 40
Menu Bar Items ................................................. 42
Adjusting the Picture ........................................ 44
Adjusting Image Preferences ..................................44
Adjusting the Color Temperature ............................ 45
Gamma Correction Function ...................................46
Emphasizing the Contrast .......................................46
Picture Setting Function...........................................47
Adjusting the Computer and
DVD/DTV Images ......................................... 48
When Auto Sync is OFF ...........................................48
Special Modes Adjustment .....................................49
Auto Sync Adjustment .............................................50
Checking the Input Signal .......................................50
Using the Options Menu ............................... 51
Checking the Lamp Life Status .............................. 51
Turning on/off the On-screen Display ......................51
Selecting the Signal Type ....................................... 52
Setting the Video Signal (VIDEO menu only)...........52
Selecting a Background Image .............................. 53Setting the Eco Mode ..............................................53
Automatic Power Shut-off Function ........................ 54
Selecting the Menu Screen Position ........................54
Selecting the Menu Color ....................................... 55
Reversing/Inverting Projected Images............ 56
AppendixMaintenance Indicators .................................... 58
Regarding the Lamp ......................................... 59
Lamp ...................................................................... 59
Caution Concerning the Lamp ................................59Replacing the Lamp ................................................59
Removing and Installing the Lamp Unit ................. 60
Resetting the Lamp Timer .......................................61
Cleaning the Ventilative Holes ......................... 62
Using the Kensington Lock.............................. 63
Troubleshooting ................................................ 63
For SHARP Assistance (U.S.A. only)............... 63
Connecting Pin Assignments .......................... 64
(RS-232C) Specifications
and Command Settings .............................. 65
Computer Compatibility Chart ......................... 66Specifications.................................................... 67
Dimensions........................................................ 68
Glossary............................................................. 69
Index................................................................... 70
CONSUMER LIMITED WARRANTY
(VALID IN USA ONLY) .................................. 71
LIMITED WARRANTY
(VALID IN CANADA ONLY) .......................... 72
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
5/74-4
1. Read InstructionsAll the safety and operating instructions should be readbefore the product is operated.
2. Retain InstructionsThe safety and operating instructions should beretained for future reference.
3. Heed WarningsAll warnings on the product and in the operating
instructions should be adhered to.
4. Follow InstructionsAll operating and use instructions should be followed.
5. CleaningUnplug this product from the wall outlet before cleaning.Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
6. AttachmentsDo not use attachments not recommended by theproduct manufacturer as they may cause hazards.
7. Water and MoistureDo not use this product near waterfor example, neara bathtub, wash bowl, kitchen sink, or laundry tub; in awet basement; or near a swimming pool; and the like.
8. AccessoriesDo not place this product on an unstable cart, stand,tripod, bracket, or table. The product may fall, causingserious injury to a child or adult, and serious damageto the product. Use only with a cart, stand, tripod,bracket, or table recommended by the manufacturer,or sold with the product. Any mounting of the productshould follow the manufacturers instructions, andshould use a mounting accessory recommended by
the manufacturer.
9. TransportationA product and cart combination
should be moved with care. Quickstops, excessive force, anduneven surfaces may cause theproduct and cart combination tooverturn.
10. VentilationSlots and openings in the cabinet are provided forventilation to ensure reliable operation of the productand to protect it from overheating. The openings shouldnever be covered or blocked by placing the producton a bed, sofa, rug, or other similar surface. This prod-uct should not be placed in a built-in installation suchas a bookcase or rack unless proper ventilation isprovided or the manufacturers instructions have been
adhered to.
IMPORTANT SAFEGUARDS
11. Power SourcesThis product should be operated only from the type ofpower source indicated on the marking label. If youare not sure of the type of power supply to your home,consult your product dealer or local power company.For products intended to operate from battery power,or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. Thisplug will only fit into a grounding-type power outlet. Thisis a safety feature. If you are unable to insert the pluginto the outlet, contact your electrician to replace yourobsolete outlet. Do not defeat the safety purpose of
the grounding-type plug.
13. Power-Cord ProtectionPower-supply cords should be routed so that they arenot likely to be walked on or pinched by items placedupon or against them, paying particular attention tocords at plugs, convenience receptacles, and the pointwhere they exit from the product.
14. LightningFor added protection for this product during a lightningstorm, or when it is left unattended and unused for longperiods of time, unplug it from the wall outlet anddisconnect the power cord. This will prevent damage
to the product due to lightning and power-line surges.
15. OverloadingDo not overload wall outlets, extension cords, or integralconvenience receptacles as this can result in a risk offire or electric shock.
16. Object and Liquid EntryNever push objects of any kind into this product throughopenings as they may touch dangerous voltage pointsor short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.17. Servicing
Do not attempt to service this product yourself asopening or removing covers may expose you to dan-gerous voltage or other hazards. Refer all servicing to
qualified service personnel.
CAUTION: Please read all of these instructions before you operate this product and save them forlater use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to
ensure your personal safety. However IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK ORFIRE HAZARD. In order not to defeat the safeguards incorporated into this Projector, observe the followingbasic rules for its installation, use and servicing. For your own protection and reliable usage of your Projector,please be sure to read these IMPORTANT SAFEGUARDS carefully before use.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
6/74
Introduction
-5
18. Damage Requiring ServiceUnplug this product from the wall outlet and referservicing to qualified service personnel under thefollowing conditions:
a. If the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen
into the product.c. If the product has been exposed to rain or water.d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operatinginstructions, as an improper adjustment of othercontrols may result in damage and will oftenrequire extensive work by a qualified technicianto restore the product to normal operation.
e. If the product has been dropped or damaged inany way.
f. If the product exhibits a distinct change in
performance.
19. Replacement PartsWhen replacement parts are required, be sure theservice technician has used replacement partsspecified by the manufacturer or have the samecharacteristics as the original part. Unauthorizedsubstitutions may result in fire, electric shock, or other
hazards.
20. Safety CheckUpon completion of any service or repairs to thisproduct, ask the service technician to perform safetychecks to determine that the product is in proper
operating condition.
21. Wall or Ceiling MountingThis product should be mounted to a wall or ceilingonly as recommended by the manufacturer.
22. HeatThis product should be situated away from heat sourcessuch as radiators, heat registers, stoves, or otherproducts (including amplifiers) that produce heat.
Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
PC/AT is a registered trademark of International Business Machines Corporation in the United States.
Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
7/74-6
IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting upyour projector.
Caution concerning the lamp unitI There is a potential hazard of glass
particles if the lamp ruptures. In case
of lamp rupture, contact your near-
est Authorized SharpVision Service
Center or Dealer for replacement.
See Replacing the Lamp on page
59.
Cautions concerning the setup of the projectorI For minimal servicing and to maintain high image qual-
ity, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the lens and part of filter must be cleaned more often
than usual. As long as the projector is properly main-
tained in this manner, use in these environments will
not reduce the overall operation life. Please note that
all internal cleaning must be performed by an Autho-
rized SharpVision Service Center or Dealer.
Do not set up the projector in places exposed to
direct sunlight or bright light.I Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes
out the colors, making viewing difficult. Close the cur-
tains and dim the lights when setting up the screen in a
sunny or bright room.
Do not subject the projector to hard impact and/
or vibration.I Take care with the lens so as not to hit or damage the
surface of the lens.
Rest your eyes occasionally.I Watching the screen for long hours continuously will
make your eyes tired. Be sure to occasionally rest your
eyes.
Do not expose the projector to extreme heat orcold.I Operating temperature:
41F to 95F (+5C to 35C)
I Storage temperature:
4F to 140F (20C to +60C)
Notes on OperationI The exhaust ventilative holes,
the lamp unit cover and adja-
cent areas may get extremely
hot during projector operation.
To prevent injury, do not touch
these areas until they have suf-ficiently cooled down.
I Allow at least 1 foot (30 cm) of space between the ex-
haust ventilative hole and the nearest wall or obstruc-
tion.
I If the cooling fan becomes obstructed, a protectiondevice will automatically turn off the projector lamp. This
does not indicate a malfunction. Remove the projector
power cord from the wall outlet and wait at least 10
minutes. Then turn on the power by plugging the power
cord back in. This will return the projector to the normal
operating condition.
Cautions regarding the transportation of the pro-
jectorI When transporting the projector, be sure not to subject
it to hard impact and/or vibration, as this can result in
damage. Take extra caution with the lens. Before mov-
ing the projector, be sure to unplug the power cord fromthe wall outlet, and disconnect any other cables con-
nected to it.
Other connected equipmentI When connecting other audio-visual equipment or a
computer to the projector, make the connections AF-
TER turning off the projector and the equipment to be
connected.
I Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
Temperature monitor functionI If the projector starts to overheat
due to setup problems or block-
age of the air vents, and
will blink in the lower left
corner of the picture. If the tem-
perature continues to rise, the lamp will turn off, the
temperature warning indicator on the projector will blink,
and after a 90-second cooling-off period the projector
will enter the standby mode. Refer to Maintenance In-
dicators on page 58 for details.
Info
The cooling fan regulates the internal temperature, and
its performance is automatically controlled. The sound
of the fan may change during projector operation due
to changes in the fan speed. This does not indicate
malfunction.
95F(+35C)
41F(+5C)
CAUTIONPRECAUCINPRCAUTION
BQC-XVZ200++1
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
8/74
Introduction
-7
The power indicatorilluminates green.
In this page, connection of the projector and the video equipment is explained as an example
for the procedure from setup to projection. Refer to each page for details.
Quick Guide
Required equipments
Video cable
(commercially available)
Projector Remote control
Insert the batteries.
(Page 11)
Power cord
1. Place the projector facing a wall or a screen.
2. Connect to video equipment. (Page 16)
6. Turn the projector on using on the remote
control. (Page 30)
3. Connect the output terminal of the video equip-ment to the input terminal of the audio equip-
ment using an audio cable.
4. Plug the power cord into the AC socket of the
projector and into the wall outlet. (Page 14)
5. Remove the lens cap from the lens.
7. Press on the remote control to select theINPUT 4 mode. (Page 31)
"On-screen Display
8. Turn on the video equipment.To INPUT 4terminal
To video out-put terminal
INPUT 4 buttonON button
ON
Power cord
Video equipment
Lens cap
Video cable(commercially available)
9. Play the video.
10.Adjust the image size, image position and the
focus. (Page 25)
Note
This projector can also be connected to a computer
as well as to video equipment. (Page 21)
Adjust the height of the imageby rotating the lens shift dial.
Adjust the focus byrotating the focus ring.
Adjust the zooming bymoving the zoom knob.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
9/74-8
Projector (Front and Top View)
Part Names
Numbers in refer to the main pages in this operation manual where the topic is explained.
30
58
58
POWER indicator
6 Exhaust ventilative hole
LAMP indicator
TEMPERATUREWARNING indicator
39ADJUSTMENT buttons(///)
39UNDO button
38 MENU button
35 RESIZE button
31 INPUT button
24 Swivel StandLOCK/UNLOCK lever
11Remote control sensor
Lens cap
Zoom knob 25
Exhaust ventilative hole 6
Focus ring 25
25Lens shift dial
39ENTER button
33KEYSTONE buttonON button30
STANDBYbutton
32
47PICTURE SETTING button
Attaching the Lens CapThe lens cap can be attached to theprojector using commerciallyavailable straps (for cellular phonesetc.), as shown in the figure.
Projector (Side and Rear View)
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
10/74
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
11/74-10
Remote Control (Front View)
Part Names
Remote Control (Top View)
FREEZE button
32
31
50
52
39
3938
39
31
3131
3135
47
35
STANDBY button
ENTER button
33KEYSTONE button
UNDO button
INPUT 1 button
INPUT 2 button
INPUT 4 button
AUTO SYNC buttonRESIZE button
PICTURE SETTING button
MENU button
30 ON button
ADJUSTMENT buttons(///)
INPUT 3 button
DIGITAL INPUT button
RGB/COMP. button
Remote control signal transmitters
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
12/74
Introduction
-11
Operating the Remote Control
I The remote control can be used to control the projector
within the ranges shown in the illustration.
Note
The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
When using the remote control:Be sure not to drop, or expose to moisture or high temperature.
The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluo-
rescent lamp.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution Insert the batteries making sure the polarities correctly match the and marks inside the battery compart-
ment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak.
Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove
them using a cloth.
The batteries included with this projector may exhaust over a short period, depending on how they are kept.Be sure to replace them as soon as possible with new batteries when they have run out.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Available Range of the Remote Control
45
23' (7 m)
30
30
45
30
Inserting the BatteriesThe batteries (two AA size) are included in
the package.
1 Pull down the tab on the coverand remove the cover towardthe direction of the arrow.
2 Insert the included batteries. Insert the batteries making sure thepolarities correctly match the and
marks inside the battery compart-
ment.
3 Insert the lower tab of thecover into the opening, andlower the cover until it clicksin place.
Remote control
Remote control
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
13/74-12
Accessories
Power cordQACCDA007WJPZ
Remote controlRRMCGA218WJSA
Two AA size batteries Terminal coverGCOVAA116WJKB
Operation manualTINS-B005WJZZ
Lens capCCAPHA004WJ01
Screws for terminal coverXBBSN40P10000
Supplied accessories
3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3CP
DVI to 15-pin D-sub adaptor (7.9'' (20 cm)) AN-A1DV
DVI cable (9'10'' (3.0 m)) AN-C3DV
Note
Some of the cables may not be available depending on the region. Please check with your nearest Autho-
rized SharpVision Service Center or Dealer.
Optional accessories
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
14/74
ConnectionsandSetup
Connections and Setup
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
15/74-14
Connecting the Projector to Other Devices
Before Connecting
Note
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and turn off
the devices to be connected. After making all connections, turn on the projector and then the other
devices.
When connecting a computer, be sure that it is the last device to be turned on after all the connec-
tions are made.
Be sure to read the operation manuals of the devices to be connected before making connections.
This projector can be connected to:
Video equipment:
I A VCR, DVD player or other video equipment (See page 15.)
I A DVD player or DTV* decoder (See page 17.)
*DTV is the umbrella term used to describe the new digital television system in the United States.
A computer using:
I DVI to 15-Pin D-sub adapter (See page 21.)
I A DVI cable (See page 22.)
I An RS-232C cable (See page 23.)
Connecting the PowerCord
Plug in the supplied power cord into
the AC socket on the rear of the pro-jector.
Power cordSupplied
accessory
-14
Power cord
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
16/74
ConnectionsandSetup
-15
Connecting to Video Equipment
S-video cable (commercially available)
To S-video output terminal
To INPUT 3 terminal
VCR or other video equipment
Connecting to Video
Equipment Using anS-video Cable (INPUT 3)Using an S-video cable, a VCR, DVD player or
other video equipment can be connected to
INPUT 3 input terminal.
1 Connect an S-video cable tothe projector.
2 Connect the S-video cable tothe video equipment.
Note
The INPUT 3 (S-VIDEO) terminal uses a
video signal system in which the picture
is separated into color and luminance sig-
nals to realize a higher-quality image. To
view a higher-quality image, use a com-
mercially available S-video cable to con-
nect the INPUT 3 terminal on the projec-tor and the S-video output terminal on the
video equipment.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
17/74
To INPUT 4 terminal
VCR or other video equipment
To video output terminal
Composite video cable
(commercially available)
Connecting to Video
Equipment Using aComposite Video Cable(INPUT 4)Using a composite video cable, a VCR, DVD
player or other video equipment can be con-
nected to INPUT 4 input terminal.
1 Connect a composite videocable to the projector.
2 Connect the composite videocable to the video equipment.
Connecting the Projector to Other Devices
-16
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
18/74
SetupandCon
nections
-17
Connecting to a DVD Player and DTV Decoder
To analog componentoutput terminal
To INPUT 1 terminals
DVD player orDTV decoder
Component cable(commercially available)
Connecting to
Component VideoEquipment Using aComponent Cable(INPUT 1)Use a component cable when connecting com-
ponent video equipment such as DVD players
and DTV decoders to INPUT 1 terminals.
1 Connect a component cable tothe projector.
2 Connect the above cable to thecomponent video equipment.
Note
Make sure to turn both the projector andthe video equipment off before connect-ing.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
19/74-18
3 RCA to 15-pinD-sub cableType: AN-C3CP
(9'10" (3.0 m))
DVI to 15-pinD-sub adaptorType: AN-A1DV(7.9" (20 cm))
Optionalaccessories
Connecting to Compo-
nent Video EquipmentUsing a 3 RCA to 15-pinD-sub Cable and theDVI to 15-pin D-subAdaptor (INPUT 2)Use a 3 RCA to 15-pin D-sub cable and the DVI
to 15-pin D-sub adaptor when connecting com-
ponent video equipment such as DVD players
and DTV decoders to INPUT 2 terminal.
1 Connect a DVI to 15-pin D-subadaptor to the projector.
2 Connect a 3 RCA to 15-pin D-sub cable to the above adaptor.
Secure the connectors by tightening the
thumbscrews.
3 Connect the above cable to thevideo equipment.
Note
When connecting this projector to com-
ponent output terminal of the DTV de-
coder, select Component for Signal
Type on the OSD menu or press on
the remote control. (See page 52.)
Make sure to turn both the projector and
the video equipment off before connect-
ing.
To analog component
output terminal
To INPUT 2 terminal
DVD player or
DTV decoder
DVI to 15-pin
D-sub adaptor
(sold separately)
3 RCA to 15-pin
D-sub cable
(sold separately)
-18
Connecting the Projector to Other Devices
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
20/74
Setup
and
Con
nections
Optional
accessory DVI to 15-pin D-sub adaptorType: AN-A1DV (7.9" (20 cm))
Connecting to RGBVideo Equipment Usingthe DVI to 15-pin D-subAdaptor and the RGB
Cable (INPUT 2)Use the DVI to 15-pin D-sub adaptor and theRGB cable when connecting RGB video equip-
ment such as DVD players and DTV decoders
to INPUT 2 terminal.
1 Connect a DVI to 15-pin D-subadaptor to the projector.
2 Connect the above adaptor toan RGB cable.
3 Connect the above cable to thevideo equipment.
Secure the connectors by tightening thethumbscrews.
Note
When connecting this projector to DVI out-
put of the DTV decoder, select RGB forSignal Type on the OSD menu or press
on the remote control. (See page 52.)
To RGB output terminal
RGB cable
(commercially
available)
To INPUT 2 terminal
DVD player or
DTV decoder
DVI to 15-pin
D-sub adaptor
(sold separately)
-19
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
21/74-20
Optional
accessory
DVI cableType:AN-C3DV(9'10'' (3.0 m))
To DIGITAL INPUT
terminal DIGITAL INPUT
TYPE switch
DVD player or
DTV decoder
To DVI digital output terminal
DVI cable
(sold separately)
-20
Connecting to Video
Equipment with the DVIOutput Terminal Usinga DVI Cable (DIGITALINPUT)Use the DVI cable when connecting video
equipment with the DVI output terminal such
as DVD players and DTV decoders to DIGITAL
INPUT terminal.
1 Slide the DIGITAL INPUTTYPE switch on the back ter-minal board to VIDEO.
2 Connect the DVI cable to theDIGITAL INPUT terminal.
3 Connect the other end to thecorresponding terminal on theDVD player or DTV decoder.
Secure the connectors by tightening thethumbscrews.
Note
Select DIGITAL INPUT mode when con-
necting to video equipment with the digitaloutput terminal. (See page 31.)
Make sure to turn both the projector andthe video equipment off before switchingthe DIGITAL INPUT TYPE switch andconnecting.
Connecting the Projector to Other Devices
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
22/74
ConnectionsandSetup
-21
Connecting to a Computer
Optional
accessory DVI to 15-pin D-sub adaptorType: AN-A1DV (7.9" (20 cm))
Connecting to a ComputerUsing the DVI to 15-pin
D-sub Adaptor and theRGB Cable (INPUT 2)
1 Connect a DVI to 15-pin D-subadaptor to the projector.
2 Connect the above adaptor toan RGB cable.
3 Connect the above cable to thecomputer.Secure the connectors by tightening the
thumbscrews.
Note
Refer to Computer Compatibility Chart onpage 66 for a list of computer signalscompatible with the projector. Use withcomputer signals other than those listed maycause some of the functions not to work.
When connecting the projector to a com-puter in this way, select RGB for SignalType on the OSD menu or press onthe remote control. (See page 52.)
A Macintosh adaptor may be required foruse with some Macintosh computers.Contact your nearest AuthorizedSharpVision Service Center or Dealer.
Depending on the computer you are us-ing, an image may not be projected unlessthe signal output setting of the computer isswitched to the external output. Refer tothe computer operation manual for switch-
ing the computer signal output settings.
To INPUT 2 terminal
Notebook computer
To RGB output terminal
RGB cable
(commercially available)
DVI to 15-pin D-sub adaptor
(sold separately)
Connecting the thumbscrew cablesI Connect the thumbscrew cable making sure that it fits cor-
rectly into the terminal. Then, firmly secure the connec-
tors by tightening the screws on both sides of the plug.I Do not remove the ferrite core attached to the RGB cable. Ferrite core
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
23/74-22
Connecting to a com-
puter with DIGITALRGB output Terminal(DIGITAL INPUT)
1 Slide the DIGITAL INPUTTYPE switch on the back ter-minal board to PC.
2 Connect a DVI cable to the pro-jector.
3 Connect the above cable to thecomputer.
Secure the connectors by tightening thethumbscrews.
Note
Select DIGITAL INPUT mode when con-necting to digital output terminal of the
computer. (See page 31.)Before switching the DIGITAL INPUT
TYPE switch and connecting, be sure tounplug the power cord of the projectorfrom the AC outlet and turn off the com-puter to be connected. After making allconnections, turn on the projector and
then the computer.Be sure that the computer is the last de-
vice to be turned on after all the connec-tions are made.
Plug and Play functionI This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
I Before using the Plug and Play function, be sure to turn on the projector first and the con-
nected computer last.
Note
The DDC Plug and Play function of this projector operates only when used in conjunction with a VESADDC compatible computer.
To DIGITAL INPUT
terminal
To DVI digital output terminal
DVI cable
(sold separately)
Desktop computer
DIGITAL INPUT
TYPE switch
Optional
accessory
DVI cable
Type:AN-C3DV(9'10'' (3.0 m))
Connecting the Projector to Other Devices
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
24/74
ConnectionsandSetup
-23
Controlling theProjector Using anRS-232C CableWhen the RS-232C terminal on the projector
is connected to a computer with an RS-232C
cable (null modem, cross type, commercially
available), the computer can be used to con-
trol the projector and check the status of the
projector. See page 65 for details.
1 Connect an RS-232C cable tothe projector.
2 Connect the above cable to thecomputer.
Note
Do not connect or disconnect an RS-232C
cable to or from the computer while it is
on. This may damage your computer.
The RS-232C function may not operate if
your computer terminal is not correctly set
up. Refer to the operation manual of the
computer for details.
Refer to Computer Compatibility Chart
on page 66 for a list of computer signals
compatible with the projector. Use with
computer signals other than those listed
may cause some of the functions not to
work.
Controlling the Projector by a Computer
Desktop computer
To RS-232C terminal
To RS-232C terminal
RS-232C cable(commercially available)
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
25/74
1
2
3
Setup
CautionDo not hold the lens when lifting, lower-
ing or rotating the projector.
When lowering the projector, be careful not
to get your fingers caught in the area be-tween the Swivel Stand and the projector.
Note
When the height or direction of the pro-
jector is adjusted, the image may become
distorted (keystoned), depending on the
relative positions of the projector and the
screen. See page 33 for details on the
keystone correction.
Using the Swivel Stand
You can adjust the angle and direction of theprojected image by using the Swivel Stand.
1 Unlock the lever on the SwivelStand.
2 Adjust the angle and directionof the projected image as youwant by lifting up the projec-tor and rotating the projector
on the Swivel Stand.
3 Lock the lever on the SwivelStand.
Removing the SwivelStand
1 Lift the projector (2) withpressing the removing-stand
button on the back of the pro-jector (1).
Adjustable up to10 from the
standard position.
Adjustable up to25 from thestandard position.
Adjustable up to3 from thestandard position.
Swivel StandLOCK/UNLOCKlever
1
2
Removing-stand button
-24
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
26/74
ConnectionsandSetup
-25
Attaching the SwivelStand
1 Align the tabs on the front bot-tom of the projector (1).
2 While holding down the button(2), place the projector ontothe Swivel Stand (3) to attach.
3 Press the projector downfirmly to attach it to the Swivel
Stand to make sure it is se-curely attached to the SwivelStand.
Focusing and ZoomingThe picture can be focused and zoomed in or
out by using the Focus ring and the Zoom
knob.
1Rotate the Focus ring until theimage on the screen comes
into focus.
2 Slide the Zoom knob. The im-age can be adjusted to the de-sired size within the zoomrange.
Using the Lens ShiftThe picture can be adjusted within the shift
range of the lens by rotating the lens shift dial
on the top of the projector using your finger.
1 3
2
Focus ring
Zoom knob
Lens shift dial
UP
DOWN
Projected Image
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
27/74-26
Adjusting the Projection Distance
Setup
Refer to pages 33 and 34 about the function of Keystone correction and placement of projector using thecorrection.
Decide the placement of the projector referring to the figures on the table and the diagram belowaccording to the size of your screen and input signal.
Center of the screen
(a)
(b)
(c)
(d)
(f)
Placement range
(e)
10
(a) Maximum projection distance(b)Minimum projection distance(c) Horizontal placement range when projection distance is maximum.(d)Horizontal placement range when projection distance is minimum.(e) Vertical placement range when projection distance is maximum.(f ) Vertical placement range when projection distance is minimum.
Note
The aspect ratio of the projected image shifts slightly when
the lens shift is at a position other than the top position. The aspect ratio of the projected image also shifts slightly
when the H Keystone and V Keystone functions areadjusted simultaneously.
When adjusting H Keystone and V Keystone at the sametime, the values of adjustable angles for each settingbecome smaller.
Keystone correction cannot be applied to On-screenDisplay.
When Keystone correction is applied, the resolution of imagecan be deteriorated to some extent.
There are errors of 3% in the formulas below.
3
4
: Screen area
: Picture area
9
16
: Picture area
When using a widescreen (16:9)In case of displayingthe 16:9 picture on thewhole of the 16:9screen.
When using a normalscreen (4:3)In case of setting the16:9 picture to the fullhorizontal width of the4:3 screen.
Screen size
(16:9)(x)
Projection distance and Keystone correction
Maximum projection distance Minimum projection distance
Diag.
200"
150"
133"
106"
100"
92"
84"
72"
60"
40"
Projection
distance (a) Composite, S-video
480I/P, 1080I720P RGB
Vertical
placement range
(e)
Projection
distance (b) Composite, S-video
480I/P, 1080I720P RGB
Vertical
placement range
(f)
Horizontal Placement range (d)Horizontal Placement range (c)
Screen size
(4:3)(x)
Projection distance and Keystone correction
Maximum projection distance Minimum projection distance
Diag.
200"
150"
100"
84"
72"
60"
40"
Horizontal Placement range (c)Projection
distance (a) Composite, S-video
480I/P, 1080I720P RGB
Vertical
placement range
(e)
Projection
distance (b) Composite, S-video
480I/P, 1080I720P RGB
Vertical
placement range
(f)
Horizontal Placement range (d)
(a) = (0.04849498x - 0.038639669) / 0.3048 x: Screen size (diag.)
(b) =(0.040201488x - 0.038804856) / 0.3048
34'6'' (10.5m)
25'10''(7.9m)
22'11''(7.0m)
18'3'' (5.6m)
17'2'' (5.2m)
15'10''(4.8m)
14'5'' (4.4m)
12'4'' (3.8m)
10'3'' (3.1m)
6'10''(2.1m)
23' 9'' (7.2m)
15' 9'' (4.8m)
13' 3'' (4.0m)
11' 4'' (3.5m)
9' 5'' (2.9m)
6' 3'' (1.9m)
7' 3'' (2.2m)
4' 7'' (1.4m)
3' 11''(1.2m)
3' 3'' (1.0m)
2' 7'' (0.8m)
1' 8'' (0.5m)
8' 2'' (2.5m)
5' 3'' (1.6m)
4' 7'' (1.4m)
3'11''(1.2m)
2'11''(0.9m)
1' 4'' (0.4m)
5'11''(1.8m)
3'11''(1.2m)
3' 3'' (1.0m)
2' 7'' (0.8m)
2' 4'' (0.7m)
1' 4'' (0.4m)
3' 11''(1.2m)
2' 7'' (0.8m)
2' 4'' (0.7m)
1' 12''(0.6m)
1' 8'' (0.5m)
' 12''(0.3m)
26'3'' (8.0m)
19' 8'' (6.0m)
13' 1'' (4.0m)
10'11''(3.3m)
9' 4'' (2.9m)
7' 9'' (2.4m)
5' 2'' (1.6m)
6' 11''(2.1m)
5' 3'' (1.6m)
3' 3'' (1.0m)
2' 11''(0.9m)
2' 4'' (0.7m)
1' 12''(0.6m)
1' 4'' (0.4m)
7' 7'' (2.3m)
5' 7'' (1.7m)
3' 7'' (1.1m)
2' 11''(0.9m)
2' 7'' (0.8m)
1' 12''(0.6m)
1' 4'' (0.4m)
5' 3'' (1.6m)
3'11''(1.2m)
2' 7'' (0.8m)
1'12''(0.6m)
1' 8'' (0.5m)
1' 4'' (0.4m)
' 12''(0.3m)
4' 7'' (1.4m)
3' 3'' (1.0m)
2' 4'' (0.7m)
1' 8'' (0.5m)
1' 8'' (0.5m)
1' 4'' (0.4m)
' 8'' (0.2m)
8' 2'' (2.5m)
6' 3'' (1.9m)
5' 7'' (1.7m)
4' 3'' (1.3m)
3' 11''(1.2m)
3' 7'' (1.1m)
3' 3'' (1.0m)
2' 11''(0.9m)
2' 4'' (0.7m)
1' 4'' (0.4m)
5'11''(1.8m)
4' 3'' (1.3m)
3'11''(1.2m)
2'11''(0.9m)
2'11''(0.9m)
2' 7'' (0.8m)
2' 4'' (0.7m)
1'12''(0.6m)
1' 8'' (0.5m)
' 12''(0.3m)
4'11''(1.5m)
3' 7'' (1.1m)
3' 3'' (1.0m)
2' 7'' (0.8m)
2' 4'' (0.7m)
2' 4'' (0.7m)
1'12''(0.6m)
1' 8'' (0.5m)
1' 4'' (0.4m)
' 8'' (0.2m)
5' 11''(1.8m)
4' 3'' (1.3m)
3' 11''(1.2m)
2' 11''(0.9m)
2' 11''(0.9m)
2' 7'' (0.8m)
2' 4'' (0.7m)
1' 12''(0.6m)
1' 8'' (0.5m)
' 12''(0.3m)
8' 6'' (2.6m)
6' 7'' (2.0m)
5' 7'' (1.7m)
4' 7'' (1.4m)
4' 3'' (1.3m)
3' 11''(1.2m)
3' 7'' (1.1m)
2' 11''(0.9m)
2' 4'' (0.7m)
1' 8'' (0.5m)
7' 7'' (2.3m)
5' 7'' (1.7m)
4' 11''(1.5m)
3' 11''(1.2m)
3' 7'' (1.1m)
3' 3'' (1.0m)
2' 11''(0.9m)
2' 7'' (0.8m)
2' 4'' (0.7m)
1' 4'' (0.4m)
28'7'' (8.7m)
21'5'' (6.5m)
18'12''(5.8m)
15'1'' (4.6m)
14'3'' (4.3m)
13'1'' (4.0m)
11'11''(3.6m)
10'3'' (3.1m)
8' 6'' (2.6m)
5' 7'' (1.7m)
11'10''(3.6m)
8' 10''(2.7m)
7' 10''(2.4m)
6' 3'' (1.9m)
5' 11''(1.8m)
5' 3'' (1.6m)
4' 11''(1.5m)
4' 3'' (1.3m)
3' 3'' (1.0m)
2' 4'' (0.7m)
10'6'' (3.2m)
7' 10''(2.4m)
6' 11''(2.1m)
5' 7'' (1.7m)
5' 3'' (1.6m)
4' 7'' (1.4m)
4' 3'' (1.3m)
3' 7'' (1.1m)
2' 11''(0.9m)
1' 12''(0.6m)(a) = (0.052833802x - 0.038639669) / 0.3048 x: Screen size (diag.)(b) =(0.043798292x - 0.038804856) / 0.3048
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
28/74
ConnectionsandSetup
-27
90
90
90
90
Upper and Lower Lens Shift Position
This projector is equipped with a lens shift function that lets you adjust the projection height. Adjust the projection height to match the setup configuration. The screen can be moved maximum the length of one screen vertically using the lens shift.
Note
Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level.Tilting or angling the projector will reduce the effectiveness of the lens shift function.
Screen size: 100 inches (254 cm)Aspect ratio: 16:9
Screen
Upper and Lower Lens Shift Position (Ceiling Mount)
When the projector is in the inverted position, use the upper edge of the screen as the base line,and exchange the lower and upper lens shift values.
Screen
Lower lens shift position(High mount setup)
Upper lens shift position(Desktop setup)
Lens center
Lens center
Screen size: 100 inches (254 cm)Aspect ratio: 16:9
Lower edge of screen (White portion) =Standard (0) point
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
29/74-28
Rear ProjectionI Place a translucent screen between the projector and the au-
dience.I Use the projectors menu screen to reverse the projected im-
age. (See page 56
for use of this func-
tion.)
Note
Optimal image quality can be achieved when the projector is
positioned perpendicular to the screen with all feet flat and lev-
eled.
Projection using a mirrorI Place a mirror (normal flat type) in front of the lens.
Info
When using a mirror, be sure to carefully position both the
projector and the mirror so the light does not shine into the
eyes of the audience.
Ceiling-mount setupI It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation.
I Before mounting the
projector, remove the
Swivel Stand. (See pages24 and 25 for removing and
attaching the Swivel Stand.)
I Before mounting the
projector, contact your
nearest Authorized
SharpVision Service Center
or Dealer to obtain the recommended ceiling-mount bracket
(sold separately). (AN-CM260 ceiling-mount bracket, AN-
EP101B extension tube for AN-CM260.)
I When the projector is in the inverted position, use the upper
edge of the screen as the base line.
I Use the projectors menu screen to select the appropriate pro-
jection mode. (See page 56 for use of this function.)
When using the default setting.MOn-screen Display
Image Projection
The image is reversed.
When using the default setting.MOn-screen Display
The image is inverted.
Setup
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
30/74
BasicOperation
Basic Operation
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
31/74-30
Image Projection
-30
TEMP. LAMP POWER
LAMP indicator
POWER indicator
ON button
INPUT button
ON button
INPUT buttons
Basic Procedure
Connect the required external equipment tothe projector before operating the following
procedures.
Info
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 31.
1 Plug the power cord into thewall outlet.The POWER indicator illuminates red,
and the projector enters standby mode.
2 Press on the remote controlor on the projector.
The blinking green LAMP indicatorshows that the lamp is warming up.Wait until the indicator stops blinkingbefore operating the projector.
If the power is turned off and then im-mediately turned on again, it may takea short while before the lamp turns on.
Note
After the projector is unpacked and
turned on for the first time, a slight
odor may be emitted from the exhaust
ventilative holes. This odor will soon
disappear with use.
When the power is on, the LAMP in-
dicator illuminates, indicating the sta-
tus of the lamp.
Green: Lamp is ready.
Green blinking: Warming up. / Cooling
down.
Red: Change the lamp.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
32/74
BasicOperation
-31
3 Press , , , oron the remote control or on
the projector to select the IN-
PUT mode.
After pressing once on the projector,
use to select the desired input mode.
Note
When no signal is received, NO SIG-NAL will be displayed. When a sig-nal that the projector is not preset toreceive is received, NOT REG. willbe displayed.
About the INPUT modes
Used for projecting im-
ages from equipmentconnected to INPUT 1terminals.
Used for projecting im-ages from equipmentconnected to INPUT 2
terminal.
Used for projecting im-ages from equipmentconnected to INPUT 3terminal.
Used for projecting im-ages from equipmentconnected to INPUT 4terminal.
Used for projecting im-ages from equipmentconnected to DIGITALINPUT terminal.
INPUT 1
(Compo-nent)
INPUT 2
(Compo-
nent/RGB)
INPUT 3(S-Video)
INPUT 4(Video)
DIGITAL
On-screen Display
Selecting the On-screen Display Lan-guageEnglish is the preset language for the On-
screen Display; however, this can be changed
to German, Spanish, Dutch, French, Italian,
Swedish, Portuguese, Chinese, Korean or
Japanese.
Display the Language menu and se-
lect the desired Language.For operating the menu screen, see
pages 38 to 41.
INPUT 1 Mode
INPUT 2 Mode
INPUT 3 Mode
INPUT 4 Mode
DIGITAL INPUT Mode
"On-screen Display (Example)
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
33/74-32-32
Turning the Power off
1 Press on the remote con-trol or on the projector,
then press or again
while the confirmation messageis displayed, to put the projec-tor into the standby mode. A dimly-lit screen is displayed for a
short time to reduce lamp damage.
Note
If you accidentally pressed
and do not want to put the projector
into the standby mode, wait until the
confirmation message disappears.
2 Unplug the power cord from theAC outlet after the cooling fanstops.
Info
Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due to
the rise in internal temperature, as
the cooling fan also stops.
When connected to equipment such
as an amplifier, be sure to turn off
the power to the equipment con-
nected first and then to the projec-
tor.
Image Projection
STANDBY button
STANDBY button
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
34/74
BasicOperation
-33
Horizontal Keystone Correction
Vertical Keystone Correction
KEYSTONE button
",',\, |buttons
KEYSTONE button
",',\, |buttons
Description
Horizontally adjusts thekeystone settings.
Vertically adjusts the
keystone settings.
V and H Keystone
adjustments are returned to
the factory preset settings.
Selected Item
H Keystone
V Keystone
Reset
Keystone CorrectionThis function can be used to adjust the Key-
stone settings.
Note
For details about using the menu screen,see pages 38 to 41.
1 Press on the projector oron the remote control.
2 Press / to select H Key-stone or V Keystone.
3 Press / to move the markon the selected adjustment
item to the desired setting.
Note
Straight lines and the edges of the
displayed image may appear
jagged, when adjusting the Key-
stone setting.
When adjusting H Keystone and
V Keystone at the same time, the
values of adjustable angles for each
setting become smaller.
The adjustable value of the V Key-
stone becomes extremely small
when H Keystone is made to be
the maximum value.
Keystone correction is disabled
while the picture mode is set to
SMART STRETCH. (See page
35.)
4 To return to the normal screen,press again.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
35/74-34
Placement of the Pro-
jected Image Using theKeystone Correction
Place the projector at a distance from thescreen that allows images to be projected ontothe screen by referring to Adjusting the Pro-jection Distance on pages 26 and 27.
1 Project the test pattern of theKeystone correction functiononto the screen. Rotate the Fo-
cus ring until the image on thescreen comes into focus. (Seepage 25.)
2 Change the projection angleusing the Swivel Stand to prop-erly project images onto thescreen. (See page 24).
3 Align the edge of the screenclosest to the projector with
the test pattern by adjustingthe zoom and the Swivel Stand.(See pages 24 and 25.)
4 Adjust the Keystone functionso that the size of the projectedimage matches the screensize. (See page 33.)
5 Align the image on the screen
by adjusting the zoom functionand the Swivel Stand.
6 Adjust the focus so that theprojected image is in focus atthe center of the screen. (Seepage 25.)
Note
The aspect ratio of the projected imageshifts slightly when the lens shift is at a
position other than the top position.The aspect ratio of the projected image
also shifts slightly when the H Keystoneand V Keystone functions are adjustedsimultaneously.
: Screen area
Image Projection
-34
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
36/74
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
37/74-36
768 576 1024 576
480I480P576I576PNTSCPAL
SECAM
VGASVGAXGA
768 576 1024 576480P
720P
1024 576
1024 576
1024 576
SIDE BAR STRETCHCINEMAZOOM
SMARTSTRETCH
1024 576
1024 576
1024 5761080I
For 4:3aspect ratio
For 16:9aspect ratio
STRETCH is fixed when 540P, 720P or 1080I signal is entered.
SMART STRETCH cannot be selected while input signal from a computer (VGA, SVGA or XGA) is entered.
480I
480P
576I
576P
NTSC
PAL
SECAM
540P
1080I
720P
VGA
SVGA
XGA
Input SignalSIDE BAR SMART STRETCH
Output screen image
STRETCHCINEMA ZOOM
4:3 aspect ratio
Letterbox
16:9 aspect ratio
Squeeze
4:3 aspect ratio
Note
SMART STRETCH cannot be selected while the Keystone correction (page 33) is being adjusted.
Keystone correction (page 33) is disabled while the picture mode is set to SMART STRETCH.
580I/580P is displayed on the screen when signal 576I/576P is input.
Image Projection
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
38/74
AdjustmentsandSettings
Adjustments and Settings
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
39/74
Using the Menu Screen
The menu screens allow you to adjust the image and various projector settings.
The menu can be operated to achieve two functions, adjustment and setting.
(For adjusting the menu items, see pages 38 and 39. For setting the menu items, see pages
40 and 41.)
Menu screen (example)
Menu Selections(Adjustments)
1 Press .The menu screen is displayed.
Note
The Picture menu screen for the
selected input mode is displayed.
-38
ENTER button
UNDO button
MENU button",',\,|buttons
ENTER button
UNDO button MENU button
",',\,|buttons
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
40/74-39
AdjustmentsandSettings
Select the menu icon.
Menu icon Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
2 Press \\\\\ or ||||| to display theother menu screens.The menu icon for the selected menu
screen is highlighted.
Note
The Fine Sync menu is not avail-able for INPUT 3 or 4.
For items on the menus, see thetree charts on pages 42 and 43.
3 Press"""""or''''' to select the itemyou want to adjust.
Note
To display a single adjustment item,
press after selecting the item.
Only the menu bar and the selected
adjustment item will be displayed.
Then if you press " or ', the fol-lowing item (Bright after Con-
trast) will be displayed.
Press to return to the previous
screen.
4 Press\\\\\ or||||| to adjust the itemselected.The adjustment is stored.
5 Press .
The menu screen will disappear.
Adjust the item.
Select
the item.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
41/74
Menu Selections
(Settings)
1 Press .The menu screen is displayed.
Note
The Picture menu screen for the
selected input mode is displayed.
2 Press \\\\\ or ||||| to display theother menu screens.The menu icon for the selected menu
screen is highlighted.
Note
The Fine Sync menu is not avail-able for INPUT 3 or 4.
For items on the menus, see thetree charts on pages 42 and 43.
-40
Using the Menu Screen
ENTER button
UNDO button
MENU button
",',\,|buttons
ENTER button
UNDO button
MENU button",',\,|buttons
Menu icon Menu screen
Picture
Fine Sync
Options
Language
PRJ Mode
Select the menu icon.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
42/74-41
AdjustmentsandSettings
3 Press""""" or''''' to select theitem you want to set.
Note
Press to return to the previous
screen.
In some menus, select the icon us-ing .
4 Press |||||.The sub menu is displayed.
5 Press""""" or''''' to select the set-ting of the item displayed in thesub menu.
6 Press .The item selected is set.
7 Press .The menu screen will disappear.
Sub
menu
Select
the item.
Sub
menu
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
43/74-42
Menu Bar Items
Language ( ) English
Deutsch
Espaol
Nederlands
Franais
Italiano
Svenska
Portugus
Front
CeilingFront
Rear
CeilingRear
Picture ( )
Tint 3030
Color 3030
Sharp 3030
Contrast 3030
Bright 3030
Red 3030
Blue 3030
Reset
5500K
6500K
8500K
9300K
10500K
Standard
Cinema 1
Cinema 2
Memory 2
Memory 3
Memory 4
Memory 5
Memory OFF
Cinema 3
7500K
CLR Temp
Gamma
White Emphasis [ON/OFF]
Picture Setting Memory 1
Fine Sync ( )
Auto Sync [ON/OFF]
Clock 3030
3030
3030
Phase 1515
H-Pos
V-Pos
Reset
Special Modes
Signal Info
Resolution
Hor Freq
Vert Freq
640480
37.5 kHz
72 Hz
640480
720480
480P
RGB
Background [None/Blue]
Options ( )
Component
Auto Power Off [ON/OFF]
Menu Position
Menu Color [Opaque/Translucent]
Center
Lamp Timer (Life)
OSD Display [ON/OFF]
Signal Type
Upper Right
Lower Right
Upper Left
Lower Left
Eco Mode [Eco/Standard]
PRJ Mode ( )
100
100
100
100
100
100
I INPUT 1 / 2 / DIGITAL INPUT Mode
Main menu Sub menu Main menu
Note
The resolution, vertical frequency and horizontalfrequency figures displayed above are forexample purposes only.
Color, Tint, and Sharp do not appear whenRGB is selected in INPUT 2 mode.
Signal Type is not displayed when usingINPUT 1.
Color, Tint, Sharp, Clock, Phase, H-
Pos, V-Pos, Special Modes and Auto Synccannot be used in the DIGITAL INPUT mode.
Clock, Phase and Auto Sync cannot beused in the Component mode.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
44/74-43
AdjustmentsandSettings
Lamp Timer (Life)
Picture ( )
Tint 3030
3030
Color 3030
Sharp
Contrast 3030
Bright 3030
Red 3030
Blue 3030
Reset
5500K
3D Progressive6500K
3D Progressive
3D Progressive8500K
3D Progressive9300K
3D Progressive10500K
3D ProgressiveStandard
3D ProgressiveCinema 1
3D ProgressiveCinema 2
3D ProgressiveMemory 2
3D ProgressiveMemory 3
3D ProgressiveMemory 4
3D ProgressiveMemory 5
Auto
3D ProgrOFFessiveMemory OFF
3D ProgressiveCinema 3
Background [None/Blue]
Options ( )
PAL
NTSC3.58
NTSC4.43
PALM
PAL60
SECAM
Language ( ) English
Deutsch
Espaol
Nederlands
Franais
Italiano
Svenska
Portugus
Auto Power Off [ON/OFF]
Menu Position
Menu Color [Opaque/Translucent]
Center
PRJ Mode ( ) Front
CeilingFront
Rear
CeilingRear
7500K
CLR Temp
Gamma
White Emphasis [ON/OFF]
Picture Setting 3D ProgressiveMemory 1
OSD Display [ON/OFF]
Video System
PALN
Upper Right
Lower Right
Upper Left
Lower Left
Eco Mode [Eco/Standard]
100
100
100
100
100
100
Note
Tint cannot be used with PAL, SECAM, PAL-M,PAL-N or PAL-60.
I INPUT 3 / 4 Mode
Main menu Sub menu Main menu
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
45/74-44
You can adjust the projectors picture to your preferences with the following picture set-
tings.
Adjusting the Picture
Adjusting Image Prefer-ences
Note
First select Memory 1-5 or Memory
OFF when you want to save the Picture
menu settings. See page 47 for details.
Adjust thePicturemenu on the menu
screen.For operating the menu screen, see
pages 38 to 41.
On-screen Display
Note
Color, Tint and Sharp do not appear
for RGB input in INPUT 2 mode.
To reset all adjustment items, select Re-
set on the Picture menu screen and
press . Tint cannot be used with PAL, SECAM,
PAL-M, PAL-N or PAL-60.
Color, Tint and Sharp cannot be used
in the DIGITAL INPUT mode.
-44
Contrast
Bright
Color
Tint
Sharp
Red
Blue
For adjusting the contrast level
For adjusting the brightness of an image
For adjusting the color intensity of an image
For adjusting the tones of an image
For making sharper or softer the contour of an image
For adjusting the redness of an image
For adjusting the blueness of an image
For less contrast
For less brightness
For less color intensity
Skin tones become purplish
For less sharpness
For weaker red
For weaker blue
For more contrast
For more brightness
For more color intensity
Skin tones become greenish
For more sharpness
For stronger red
For stronger blue
Selected Item Description \ button | button
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
46/74-45
AdjustmentsandSettings
Adjusting the ColorTemperature
This function allows for selecting the desired
color temperature. With the lower value se-
lected, the projected image becomes warmer,
reddish and incandescent-like while with thehigher value, the image becomes cooler, blu-
ish and fluorescent-like.
Select CLR Temp in the Picture
menu on the menu screen.
For operating the menu screen, see
pages 38 to 41.
On-screen Display
5500K
6500K
7500K
8500K
9300K
10500K
Selected Item Description
The less the value is set to, the
warmer, reddish, incandescent-likethe image becomes.
The more the value is set to, the
cooler, bluish, fluorescent-like the
image becomes.
CLR Temp is fine adjusted by following the
procedure below.
1 Select CLR Temp in the Pic-
ture
menu on the menuscreen and press .A single menu bar of CLR Temp is
displayed.
2 Press''''' or""""" to fine adjust thecolor temperature.With the lower value selected, the pro-
jected image becomes magenta-
tinged. With the higher value selected,
the projected image becomes green-
tinged.
Pressing \ or| changes the value ofthe color temperature in the sub menu.
Note
Values on CLR Temp are only for gen-
eral standard purposes.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
47/74-46
Gamma Correction
FunctionGamma is an image quality enhancement
function.
Four gamma settings are available to allow for
differences in the brightness of the room.
Select Gamma in the Picture menu
on the menu screen.For operating the menu screen, see
pages 38 to 41.
Adjusting the Picture
On-screen Display
-46
Emphasizing the Con-trast
This function emphasizes the bright portions
of images to obtain a higher contrast image.
Select White Emphasis in the Pic-
ture menu on the menu screen.For operating the menu screen, see
pages 38 to 41.
On-screen Display
Standard
Cinema 1
Cinema 2
Cinema 3
Selected Item Description
Standard picture without gamma
correction
Gives greater depth to darker portions
of images.
Brightness is toned down and the
image becomes more balanced.
Brighten the darker portions of images
for easier viewing in a dimly lit room.
(ON)
(OFF)
Selected Item Description
For emphasizing the bright portions of
images
For disabling White Emphasis
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
48/74-47
AdjustmentsandSettings
Settings of all items in Picture can be
stored for the respective input modes.
The stored settings can be selected in
any input modes.Besides Memory 1 to Memory 5,
other settings on the Picture menu
can be stored for each input mode.
The settings stored in Memory OFF
cannot be applied when another input
mode is selected.
Memory
1-5
Memory
OFF
Selected Item Description
On-screen Display
PICTURE SETTING button
PICTURE SETTING
button
Picture Setting Func-tionThis function stores all items set in Picture.
Five settings can be stored separately in
Memory 1 to Memory 5. Each stored set-
ting is reassigned to each input mode (INPUT1 to INPUT 4 and DIGITAL).
Even when the input mode or signal is
changed, you can easily select optimal set-
tings from the stored settings.
IStoring the Adjustment Val-ues for Each Memory Num-ber
SelectPicture Settingon thePicture
menu and the memory location whereyou want to store the settings. Then
adjust the setting items on thePicture
menu.
For operating the menu screen, seepages 38 to 41.
IApplying the Stored Settings
If you want to apply the stored settings
on thePicture
menu, select
Picture
Setting on the Picture menu and thememory location where you havestored the settings.
Note
This function can be operated using the
on the projector or on the remote
control, as well as the OSD menu screen.
Each time or is pressed, the
memory number changes as shown be-
low.
Memory 1 Memory 2 Memory 3
Memory OFF Memory 5 Memory 4
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
49/74-48
Adjusting the Computer and DVD/DTV Images
Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in
portions of the screen.
When Auto Sync is OFFWhenAuto Sync isOFF, interference such
as flickering or vertical stripes may occur if
displaying tilings or vertical stripes. Should
this occur, adjust Clock, Phase, H-Pos
and V-Pos for obtaining an optimum image.
Select Clock, Phase,H-Pos or V-
Pos
in theFine Sync
menu on themenu screen.
For operating the menu screen, see
pages 38 to 41.
Note
Clock, Phase, H-Pos and V-Pos can-
not be used in the DIGITAL INPUT mode.
Clock and Phase cannot be used in the
Component mode.
Computer image adjustments can be
made easily by pressingAUTO SYNC
on the re-
mote control. See page 50 for details.
To reset all adjustment items, select Re-
set on the Fine Sync menu screen and
press .
The adjustable area of each item may be
changed according to the input signal.
On-screen Display
-48
Selected Item Description
Clock
Phase
H-Pos
V-Pos
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
50/74-49
AdjustmentsandSettings
On-screen Display
Special Modes Adjust-mentOrdinarily, the type of input signal is detected
and the correct resolution mode is automati-
cally selected. However, for some signals, the
optimal resolution mode inSpecial Modes
on the Fine Sync menu screen may need
to be selected to match the computer display
mode.
Set the resolution by selecting SpecialModes in the Fine Sync menu on themenu screen.For operating the menu screen, seepages 38 to 41.
NoteAvoid displaying computer patterns which
repeat every other l ine (horizontal
stripes). (Flickering may occur, making
the image hard to see.)
When inputting DTV 1080I signal, select
the corresponding type of signal.
When inputting 720P signal from the
video equipment, select 720P. When
inputting 1280 720 signal from the com-
puter, select HTPC.
Special Modes cannot be used in the
DIGITAL INPUT mode.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
51/74
On-screen Display
-50
Adjusting the Computer and DVD/DTV Images
AUTO SYNC button
On-screen Display
(ON)
(OFF)
Selected Item Description
Auto Sync adjustment will occurwhen the projector is turned on or
when the input signals are switched,
when connected to a computer.
Auto Sync adjustment is not
automatically performed.
Auto Sync Adjustment
Used to automatically adjust a computer im-age.
Select whether the image is to be synchro-
nized automatically when switching the sig-
nal with ON or OFF.
Select Auto Sync in the Fine Sync
menu on the menu screen.For operating the menu screen, see
pages 38 to 41.
Note
When the optimum image cannot beachieved with Auto Sync adjustment, use
manual adjustments. (See page 48.)The Auto Sync adjustment may take
some time to complete, depending on theimage of the computer connected to theprojector.
Auto Sync cannot be used in the DIGI-TAL INPUT mode.
Auto Sync adjustment is also performedby pressing AUTO SYNC on the remote control.
Checking the Input SignalThis function allows you to check the current
input signal information.
Select Signal Info in the Fine Syncmenu on the menu screen.For operating the menu screen, seepages 38 to 41.
Note
540P is displayed on the screen when
signal 1080I is inputted during DVI con-
nection.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
52/74-51
AdjustmentsandSettings
(ON)
(OFF)
Checking the Lamp Life
StatusYou can confirm the cumulative lamp usagetime and the remaining lamp life (percentage).
Display the Options menu to checkthe lamp life status.For operating the menu screen, seepages 38 to 41.
Note
It is recommended that the lamp bechanged when the remaining lamp lifebecomes 5%.For lamp replacement, contact your near-est Authorized SharpVision Service Cen-ter or Dealer.
The table above indicates rough estimatesin the case of using only in each modeshown. Remaining lamp life changes withinthe range of the values shown dependingon the frequency at which Eco Mode isswitched to (Eco mode) and (Standard mode) (see page 53).
Using the Options Menu
On-screen Display
On-screen Display
All On-screen Displays aredisplayed.
INPUT/FREEZE/AUTO SYNC/An invalid button has beenpressed. are not displayed.
Selected Item Description
Turning on/off the On-screen DisplayThis function allows you to turn on or off the
on-screen messages that appear during input
select.
Select OSD Display in the Options
menu on the menu screen.For operating the menu screen, see
pages 38 to 41.
Remaining lamp life
100% 5%
Approx. Approx.4,000 hours 200 hours
Approx. Approx.3,000 hours 150 hours
Lamp usage condition
Operated exclusively
in Eco mode ( )
Operated exclusively
in Standard mode ( )
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
53/74-52
Using the Options Menu
-52
Selecting the Signal
TypeThis function allows you to select the input
signal type Component or RGB for INPUT 2.
Select Signal Type in the Options
menu on the menu screen.For operating the menu screen, seepages 38 to 41.
Note
RGB or Component can be selected
with on the remote control only in
INPUT 2.
On-screen Display
Setting the Video Signal(VIDEO menu only)The video input system mode is preset to
Auto; however, it can be changed to a spe-
cific system mode if the selected system mode
is not compatible with the connected audiovi-
sual equipment.
Select Video System in the Options
menu on the menu screen.For operating the menu screen, see
pages 38 to 41.
Note
When the system mode is set to Auto,you may not receive a clear picture dueto signal differences. Should this occur,switch to the video system of the sourcesignal.
Auto cannot be set for PAL-M and PAL-N input signals. Select PAL-M or PAL-N in Video System menu for PAL-M and
PAL-N input signals.
On-screen Display
Set when RGB signals are
received.
Set when Component signals
are received.
RGB
Component
Selected Item Description
RGB/COMP. button
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
54/74-53
AdjustmentsandSettings
Selecting aBackground ImageThis function allows you to select the image
displayed when no signal is being sent to the
projector.
Select Background in the Optionsmenu on the menu screen.For operating the menu screen, seepages 38 to 41.
Blue screen
Black screen
(Blue)
(None)
Selected Item Description
On-screen DisplaySetting the Eco ModeThis function allows you to select the desired
power consumption mode.
Select Eco Mode in the Optionsmenu on the menu screen.For operating the menu screen, seepages 38 to 41.
Note
Although lamp life and noise are improvedwhen Eco Mode is set to (Ecomode), brightness decreases by 20%.
Eco Mode is factory preset to (Stan-dard mode).
(Eco mode)
(Standard mode)
Brightness
80%
100%
Power consumption
230 W
285 W
Selected Item Lamp life
Approx.4,000 hours
Approx.3,000 hours
On-screen Display
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
55/74-54-54
Using the Options Menu
Selecting the MenuScreen PositionThis function allows you to select the desired
position of the menu screen.
Select Menu Position in the Optionsmenu on the menu screen.
For operating the menu screen, see
pages 38 to 41.
On-screen Display
Center
UpperRight
LowerRight
UpperLeft
LowerLeft
Selected Item
The menu is displayed on thecenter of the image.
The menu is displayed on theupper right of the image.
The menu is displayed on thelower right of the image.
The menu is displayed on theupper left of the image.
The menu is displayed on thelower left of the image.
Description
On-screen DisplayAutomatic Power Shut-
off FunctionWhen no input signal is detected for more than15 minutes, the projector will automatically en-
ter the standby mode if set to (ON).
Select Auto Power Off in the Optionsmenu on the menu screen.For operating the menu screen, seepages 38 to 41.
Note
Auto Power Off is factory preset to . When the Auto Power Off function is set to (ON), 5 minutes before the projectorenters the standby mode, the message En-ter STANDBY mode in X min. will appear onthe screen to indicate the remaining minutes.
Selected Item Description
Projector automatically enters the
standby mode after 15 minuteswithout an input signal.
Automatic Power Shut-off disabled.
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
56/74-55
AdjustmentsandSettings
Selecting the MenuColorThis function allows you to select the color of
the menu screen.
Select Menu Color in the Options
menu on the menu screen.For operating the menu screen, see
pages 38 to 41.
On-screen Display
The menu is displayed
opaquely.
The menu is displayedtranslucently. The par t of themenu on the image becomestransparent.
(Opaque)
(Translucent)
Selected Item Description
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
57/74-56-56
Reversing/Inverting Projected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or
invert the projected image for various applications.
Setting the ProjectionMode
Display the PRJ Mode menu and se-
lect the desired projection mode.
For operating the menu screen, see
pages 38 to 41.
Note
This function is used for the reversed im-age and ceiling-mount setups. See page 28for these setups.
On-screen Display
Normal image
Inverted image
Reversed image
Reversed and inverted image
Front
CeilingFront
Rear
CeilingRear
Selected Item Description
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
58/74
Appen
dix
Appendix
-
8/14/2019 IBJSC.com | I-WEB.com.vn - Projector Manual 2217
59/74-58
Maintenance Indicators
I The warning lights on the projector indicate problems inside the projector.
I If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter the standby mode. After the projector has entered the standby
mode, follow the procedures given below.
TEMPERATUREWARNINGindicator
POWERindicator
LAMPindicator
TEMP. LAMP POWER
About the temperature warning indicatorIf the temperature inside the
projector increases, due toblockage of the air vents, or the
setting location, will
illuminate in the lower left corner of the picture. Ifthe temperature keeps on rising, the lamp will turn offand the temperature warning indicator will blink, thecooling fan will run for a further 90 seconds, and then
the projector will enter the standby mode. After appears, be sure to perform the following
measures.
About the lamp indicator
IThe lamp life becomes 0%, when used
for approximately 4,000 hours with Ecomode or when used for approximately3,000 hours with Standard mode (seepage 53).
IWhen the remaining lamp life becomes5% or less, (yellow) will be displayedon the screen. When the percentage be-comes 0%, will change to (red),the lamp will automatically turn off and
then the projector will automatically en-ter the standby mode. At this time, thelamp indicator will illuminatein red.
I If you try to turn on the projector a fourth
time without replacing the lamp, the pro-jector will not turn on.
Maintenance indicatorCondition Problem Possible Solution
Temperaturewarningindicator
Normal Abnormal
OffRed on/Standb