Download - IEC 897 (1987)
-
7/25/2019 IEC 897 (1987)
1/30
NORME INTERNATIONALE
INTERNATIONAL STANDARD
Commission Electrotechnique n ern
a t
onale
International Electrotechnical Commission
Mem,qyHapo,qtiaR 3 n e ~ ~ p o ~ e x ~ ~ q e c ~ a ~OM
MCCMR
Mthodes de dtermination de la tension de claquage
au choc de foudre des liquides isolants
Methods for the determination of the lightning impulse
breakdown voltage of insulating liquids
~-
~
CE1
IEC
897
Premire dition
First edition
1987
Publication
897: 1987
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
2/30
Rvision de la prsente publication
Le contenu technique des publications de
la
CE 1 est constam- .
ment revu par la Commission afin dassurer quil reflte bien ltat
actuel de
la
technique.
Les renseignements relatifs
ce travail de rvision,
ltablis-
sement des ditions rvises et aux mises
jour peuvent tre
obtenus auprs des Comits nationaux de la CE1et en consultant
les documents ci-dessous:
Bulletin de la CE 1
Annuaire de la CE 1
e
Catalogue des publications de la CE1
Publi annuellement
Terminologie
En ce qui concerne
la
terminologie gnrale, le lecteur se repor-
tera
ia
Publication 50 de la CE I : Vocabulaire Electrotechnique
International (VEI), qui est tablie sous forme de chapitres spars
traitant chacun dun sujet dfini, lIndex gnral tant publi spa-
rment. Des dtails complets sur le VE1 peuvent tre obtenus sur
demande.
Les termes et dfinitions figurant dans la prsente publication
ont t soit repris du VEI, soit spcifiquement approuvs aux fins
de cette publication.
Symboles graphiques et littraux
Pour les symboles graphiques, symboles littraux et signes
dusage gnral approuvs par la CEI , le lecteur consultera:
-
a
Publication 27 de
la
CEI : Symboles littraux
utiliser en
-
a
Publication 617 de la CEI: Symboles graphiques pour
lectrotechnique :
schmas.
Les symboles et signes contenus dans
la
prsente publication ont
t soit repris des Publications 27 ou 617 de
la
CE I, soit spcifi-
quement approuvs aux fins de cette publication.
Publications de la CE1 tablies par le m me
Comit dEtudes
Lattention du lecteur est attire sur
la
page
3
de
la
couverture,
qu i
numre les publications de la CE I prpares par le Comit
&Etudes qui a tabli
la
prsente publication.
Revision of this publication
The technical content of I EC publications is kept under con-
stant review by the
I
EC, thus ensuring that the content reflects
current technology.
Information on the work of revision, the issue of revised edi-
tions and amendment sheets may be obtained from
I
EC National
Committees and from the following I EC sources:
I E C Bulletin
e I E C Yearbook
8
Catalogue of I E C Publications
Published yearly
Terminology
For general terminology, readers are referred to
I
EC Publi-
cation
50:
International Electrotechnical Vocabulary (IEV), which
is issued in the form of separate chapters each dealing with a
specific field, the General Index being published as a separate
booklet. Full details of the IEV will be supplied on request.
The terms and definitions contained in the present publication
have either been taken from the IEV or have been specifically
approved for the purpose
of
this publication.
Graphical and letter symbols
For graphical symbols, and letter symbols and signs approved
by the
I
EC for general use, readers are referred to :
- I EC Publication 27: Letter symbols to be used in electrical
-
I E C Publication 617: Graphical symbols for diagrams.
technology;
The symbols and signs contained in the present publication
have either been taken from I E C Publications 27 or 617, or have
been specifically approved for the purpose of this publication.
I EC
publications prepared by the same
Technical Committee
The attention of readers is drawn to the inside of the back cover,
which lists
I
EC publications issued by the Technical Committee
which has prepared the present publication.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
3/30
NORME INTERNATIONALE
INTERNATIONAL STANDARD
CE1
IEC
C o mm ssion E ect rotechn qu e In erna
t
o na e
897
In ternat ional Electrotechnical Com mis sion
M e M , q y H a p O ~ H a F I
~ J I ~ H T ~ O T ~ X H H ~ ~ C H ~ F IOMHCCHFI
Premire dition
First edition
1987
Mthodes de dtermination de
la
tension de claquage
au choc de foudre des liquides isolants
Methods for th e determination of the lightning impulse
breakdown vol tage of insulating liquids
O CE1
1987
Droits de reproduction rservs
-
Copyright
-
all rights reserved
Aucune partie de cette publication ne peut tre reproduite ni utilise sous que que
forme que ce soit et -par aucun procd, lectronique ou mcanique. y compris la
photocopie et les m:croh ms. sans l'accord crit de l'diteur.
No part of this publication maybe reproducedorutilized n anyformorby anymeans.
electronic or mechanical, including photocopying and rnicroklm. without permission
in writing from the pub isher.
Bureau Central de la Commission Electrotechnique Internationale
3,
rue de Varemb Genve, Suisse
Codeprix 16
Price code
pour prix,
wi r catalogue
en vigueur
For priee, see cerrenl eaiaiogue
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
4/30
I
I E C 8 7 7
8 7 Li84989L 0 0 8 7 1 7 7
5
- 2 -
897
O
CE1 1987
SOMMAIRE
Pages
PRAMBULE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
PRFACE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Articles
1 Domaine d'application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Considrations gnrales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Documents de rfrence
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
4
.
Appareillage
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
5
.
Echantilonnage du liquide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
6. Prparation et entretien de la cellule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7. Prparation de l'essai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8. Procdures d'essai
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
8
i
Mthode A
-
Essai par chelons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
8.2 Mthode B - Test progressif . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9. Rapport.&essai . . .
.'. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
ANNEXE
.
est progressif de comparaison de la probabilit de claquage des dilectriques
liquides une valeur normalise.onstruction d'un graphe de dcision . . . . 18
ANNEXE. esurage des rayons de courbure des aiguilles . . . . . . . . . . . . . . . . . . . .
24
FIGURES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
5/30
897 O
IEC
1987
~
I E C
877 8 7 W 484487L.0089378
7 =
- 3 -
CONTENTS
Page
FOREWORD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Clause
1
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. Documents referred to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
. Apparatus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Sampling of the liquid
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. Preparation and maintenance of the cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. Preparation of test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
.
Test procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 Method A
-
Step test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2 Method B
-
Sequential test
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX
.
equential test for comparison of the breakdown probability of liquid dielectrics
APPENDIX
.
easurement of radius of curvature of needles
with a standard value
.
onstruction of a ruling graph . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
7
7
9
9
11
11
11
13
13
15
17
19
25
26
IGURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
6/30
- 4 -
COMMISSION LECTROTECHNIQUE INTERNATIONALE
897
O
CE1 1987
MTHODES DE DTERMINATION
DE LA TENSION DE CLAQUAGE AU CHOC DE FOUDRE
DES LIQUIDES ISOLANTS
PRAMBULE
i)
Les
dcisionsou accords officiels de
la
CE1 en ce qui concerne les questions echniques, prpars par des Comits Etudes
O
sont
reprsents tous les Comits nationaux s'intressant ces questions, expriment, dans ia plus grande mesure possible, un accord
international
sur
les sujets examins.
2) Ces dcisions constituent des recommandations internationales et sont agres comme telles par les Comits nationaux.
3)
Dans le but d'encourager l'unification internationale,
la
CE1 exprime le vu que tous les Comits nationaux adoptent dans leurs
rgles nationales le texte de
la
recommandation de
la
CEI , dans
la
mesure
O
les conditions nationales le permettent. Toute
divergence entre
la
recommandationde laCE1 et
ia
rgle nationale correspondantedoit, dans lamesure du possible, tre indique
en termes clairs dans cette dernire.
PRFACE
La prsente norme a t tablie par le Sous-Comit10A: Huiles isolantes base d'hydrocarbures, du
Le
texte de cette norme est issu des documents suivants:
Comit &Etudes no 10 de la C EI : Fluides pour applications lectrotechniques.
Rgle des
Six
Mois Rapport de vote
OA(BC)68
0A(BC)64
Pour de plus amples renseignements, consulter le rapport de vote mentionn dans le tableau ci-
dessus.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
7/30
897 O IEC 1987 5
INTERNATIONAL ELECTR~TECHNICAL
COMMISSION
METHODS FOR THE DETERMINATION
OF THE LIGHTNING IMPULSE BREAKDOWN VOLTAGE
OF INSULATING LIQUIDS
FOREWORD
i)
The formal decisions or agreements
of
the IEC on technical matters, prepared byTechnica1 Committees
on
which all the National
Committees having a special interest therein are represented, express, as nearly as possible, an international consensus of opinion
on the subjects dealt with.
2)
They have the form of recommendations. for international use and they are accepted by the National Committees in that
3)
In order to promote international unification, the I EC expresses the wish that all National Committees should adopt the text of
the I EC recommendation for their national
rules
in
so
far as national conditions will permit. Any divergence between the IEC
recommendation and the corresponding national rules should, as far as possible, be clearly indicated in the latter.
sense.
PREFACE
This standard has been prepared by IEC Sub-committee IOA: Hydrocarbon Insulating Oils, of IE C
The text of this standard is basedon the following documents:
Technical Committee No. 1O
:
Fluids for Electrotechnical Applications.
Six Months Rule Report on Voting
lOA(C0)64 1OA(C0)68
Further information can be found in the Reporton Voting indicated in the table above.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
8/30
I E C
8 9 7
8 7
LI8114891 008918L
7
- 6 -
897 O CE1 1987
MTHODES DE DaTERMINATION
DE LA TENSION DE CLAQUAGE AU CHOC DE FOUDRE
DES LIQUIDES ISOLANTS
1. Domaine d'application
1.1
La
prsente norme dcrit deux mthodes d'essaiA et B pour estimer la rigidit lectrique en champ
divergent de liquides isolants au choc de foudre normalis.
La mthode A repose sur une mthode par chelons destine valuer, dans des conditions
dtermines, la tension de claquage au choc.
La mthode B est un test statistique destin contrler une hypothse concernant la probabilit
de claquage d'un liquide isolant, pour un niveau de tension donn.
1.2
Les
deux mthodes s'appliquent aux liquides isolants neufs ou usags de viscosit infrieure
700 mm2/s
40
C.
Ces mthodes peuvent tre utilises en polarit ngativeou positive. Aucune exigence particu-
lire n'est demande concernant la prparation de l'chantillon du liquide, pourvu qu'il satisfasse
l'usage industriel; cependant, des essais raliss avant et aprs traitement de I'chantilion peuvent
tre utiles pour en montrer l'influence.
1.3 Ces deux mthodes sont principalement destines tablir des procdures normalises d'valuation
de la rigidit lectrique au choc des liquides isolants. Elles peuvent servir diffrencier les liquides
dilectriques entre eux et dtecter des variations de leurs caractristiques, provenant de modifi-
cations de leur composition chimique qui rsulteraient de changement du processus de fabrication
ou des produits de base.
2. Considrations gnrales
2.1 Les liquides isolants utiliss dans les appareils lectriques peuvent tre soumis une contrainte de
tension de choc de foudre ou bien de manuvre, superpose au fonctionnement permanent
frquence industrielle.
Que ces surtensions soient unidirectionneiles ou oscillantes,il en rsultera toujours
un
fonction-
nement transitoire, de polarit ngative ou positive, ncessitant, dans ces conditions, de connatre le
comportement du liquide isolant utilis.
Cependant, il est ncessaire d'acqurir une plus grande exprience pour tablir une corrlation
entre les rsultats de tension de claquage au choc des liquides, obtenus avec des cellules d'essai
gomtrie d'lectrodes pointe-sphre, et leur application dans les systmes d'isolation.
2.2
Le
claquage au choc des liquides isolants est un phnomne complexe qui n'est pas encore
totalement lucid; il requiert l'initiation et la propagation d'une perturbation de prrupture
(streamers).
On a pu constater que la tension de claquage dpend de facteurs tels que: forme de la tension,
dure d'application et configuration du champ.
Pour obtenir des rsultats comparables,il faut prciser tous ces facteurs et les matriser troite-
ment. Mme ainsi, on observe frquemment une dispersion des rsultats que l'on suppose due
la
nature alatoire des mcanismes de prrupture.
2.3 Alors qu'en champ symtrique, le comportement au claquage ne dpend pas de la polarit de la
tension applique, cette polarit a un effet marqu en champs divergents, particulirement en
gomtrie pointe-sphre. L'exprience a montr, dans
ce
cas, que la composition chimique du
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
9/30
897 O I EC 1987 - 7 -
METHODS
FOR
THE DETERMINATION
OF
THE LIGHTNING IMPULSE BREAKDOWN VOLTAGE
OF INSULATING LIQUIDS
1.
Scope
1.1
1.2
1.3
This
standard describes two test methods,
A
and Byfor assessing the electric strength of insulating
liquids in a divergent field when subjected to standard lightning impulse.
Method
A
is based on a step procedure intended to provide an estimate of impulse breakdown
voltage under specific conditions.
~=
Method B is a statistical test designed to check an hypothesis about the impulse breakdown
probability of an insulating liquid at a given voltage level.
Both methods can be applied to unused
or
used insulating liquids, the viscosity of which is lower
than
700
mm2/s at
40 C.
The methods can be used with positive or negative impulses.
No
specific stipulations are made
regarding the preparation of the liquid sample provided that it corresponds to industrial practice;
however, tests made before and after treatment of the sample may be useful for demonstrating the
effect of treatment.
Both methods are primarily intended to establish standardized procedures for assessing the impulse
electric strength of insulating liquids. They may serve to differentiate dielectric liquids between
each other and to detect variations in their characteristics due to modifications in their chemical
composition as the result of changes in the manufacturing process and/or feed-stocks.
2.
General
2.1 Insulating liquids in service in electrical apparatus may be subjected to switching or lightning
transient voltage stress superimposed on continuous operation voltage at power frequency.
Whether such surges be unidirectional or oscillatory, the result will always be a transient oper-
ation with positive or negative polarity, requiring knowledge of the behaviour of the insulating
liquid under these conditions.
However, much more experience is necessary before the results of impulse breakdown voltage
obtained in test cells employing point-to-sphere electrode geometry can be correlated with perfor-
mance of the liquid in practical insulation systems.
2.2 In insulating liquids, impulse breakdown is a complex phenomenon, still not
fully
understood;
it
requires the initiation and the propagation of
a
prebreakdown disturbance (streamers).
Breakdown voltage appears to be determined by such factors as voltage wave shape, duration of
the applied voltage and field configuration.
To obtain comparable results it is necessary for all these factors to be clearly defined and kept
under close control. Even
so,
however, a spread of results is frequently observed which is believed
to be associated with the random nature of prebreakdown mechanisms.
2.3 Whilst breakdown behaviour in a symmetrical field is not affected by the polarity of voltage applied,
polarity does have a marked effect in divergent fields, particularly in point-to-sphere geometry.
In this configuration, experience has shown that the chemical composition of the liquid has a
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
10/30
- 8 - 897
O
CE1 1987
liquide joue un rle essentiel dans la dtermination des proprits de claquage au choc en onde
ngative.
En consquence, des gomtries
champ fortement divergent, telles qu'elles sont utilises dans
les mthodes dcrites, sont indispensables pour fake apparatre des diffrences d'effets dues la
composition des liquides isolants.
2.4 La tension de claquage au choc dpend de la dure de front de l'onde. En consquence, les mthodes
dcrites spcifient seulement l'emploi de l'onde pleine normale (1,2/50).
2.5
A
la diffrence de la tension de claquage frquenceliidustrielle (Publication 156 de la CEI), la
tension de claquage au choc pointe-sphre est en grande partie indpendante de polluants tels que
eau et parti'cules. Ainsi, aucune disposition particulire n'est prvue pour en tenir compte, pourvu
que leurs concentrations n'excdent pas les valeurs limites d'utilisation du liquide.
3.
Documents d e rfrence
Publications de la CE
:
52 (1960):
60-1 (1943):
. 60-2 (1973):
60-3 (1976):
60-4 (1977):
71-1 (1976):
71-2 (1976):
156 (1963):
475 (1974):
Recommandations pour la mesure des tensions au moyen d'clateurs
sphres
(une sphre
la terre).
Techniques des essais
haute tension, Premire partie: Dfinitions et
prescriptions gnrales relatives aux essais.
Deuxime partie: Modalits d'essais.
Troisime partie: Dispositifs de mesure.
Quatrime partie:Guide d'application des dispositifs de mesure.
Coordination de l'isolement. Premire partie: Termes, dfinitions, principes et
rgles.
Deuxime partie: Guide d'application.
Mthode pour la dtermination de la rigidit lectrique des huiles isolantes.
Mthode d'chantillonnage des dilectriques liquides.
Normes ISO:
2854
(1976): Interprtation statistique des donnes - Techniques d'estimation et tests
portant sur des moyennes et des variances.
3534 (1977): Statistique- Vocabulaire et symboles.
5725
(1986): Fidlit des mthodes d'essai
-
Dtermination de la rptabilit et de la repro-.
ductibilit par essais interlaboratoires.
4.
Appareillage
4.1
Gnrateur de choc
Le gnrateur de choc doit fournir une onde pleine normale 1,2/50, de polarit ngative ou
positive, conformment la Publication 60-
1
de la CE I, avec la prcision dfmie dans la Publica-
tion 60-2 de la CE1
;
en particulier, il est ncessaire que la mesure de tension de crte soit obtenue
&
3%. La tension nominale du gnrateur doit tre au moins de 300 kV et des nergies de sorties
comprises entre 0,l kJ et 20 kJ sont convenables.
4.2
Rglag e de la tension de choc
Cette opration est trs importante. I1 convient donc de prdterminer la tension de crte
1%
prs, au moyen d'un groupe de charge
commande manuelle ou, mieux,
l'aide de disRositifs de
dclenchement automatique dont la prcision de rglage est de 0,5%.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
11/30
L E C 8 9 7 87 = 48448cl3
~
0089384
2
W
~
897 O I EC 1987 - 9 -
fundamental role
in
determining the negative impulse breakdown properties.
Highly divergent field geometries, as used in the methods described, are therefore necessary to
differentiate composition effects in insulating liquids.
2.4 Impulse breakdown voltage depends on wave front duration. Consequently, the methods described
specify only the standard full impulse wave (1.2/50).
2.5 Unlike power frequency breakdown voltage (IEC Publication 156), the point-to-sphere impulse
breakdown is largely independent of such contaminants as moisture and particles. Accordingly, no
specific provisions are made to control these contaminants, provided their concentrations do not
exceed the serviceability limits of the liquid.
3. Documents referred to
IEC Publications:
52
(1
960): Recommendations for Voltage Measurement by means of Sphere-gaps (One
Sphere Earthed).
60-1 (1973): High-voltage Test Techniques, Part
1:
General Definitions and Test
Requirements.
60-2 (1973): Part 2: Test Procedures.
60-3 (1976): Part 3: Measuring Devices.
60-4
(1
977): Part 4: Application Guide for Measuring Devices.
71-1
(1976): Insulation Co-ordination, Part 1
:
Terms, Definitions, Principles and Rules.
71-2 (1976): Part 2: Application Guide.
156 (1963):
475 (1974): Method
of
Sampling Liquid Dielectrics.
I S 0 Standards:
2854
(1976): StatisticalInterpretation
of
Data
-
Techniques of Estimation and Tests relating
to Means and Variances.
3534 (1977): Statistics-Vocabulary and Symbols.
5725
(1
986): Precision of Test Methods-Determination of Repeatability and Reproducibil-
ity by Interlaboratory Tests.
Method for the Determination of the Electric Strength of Insulating Oils.
4. Apparatus
4.1
Imp ulse generator
The impulse geneator shall be capable of producing standard 1.2/50 full wave, adjustable to
positive or negative polarity in accordance with I EC Publication 60-1 and with accuracy as defined
in IEC Publication 60-2; in particular, measurement to within %
of
the crest voltage is necess-
ary. The generator shall have a voltage rating of at least 300 kV and output energies in the range of
0.1
kJ to 20
kJ
are appropriate.
4.2
Adjustment of impulse voltage
This operation is very important. The crest voltage should therefore be predetermined to within
1%by a manual control charging apparatus or, preferably, by means of an automatically triggered
apparatus with a regulating accuracy of .5%.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
12/30
I E C
8 9 7
87 =
48Ll48'73
0 0 8 9 3 8 5 4
M
- 10 - 897 O CE1 1987
4.3 Me surage de la tension de choc
I1 est conseill d'effectuer ce mesurage suivant les Publications 60-3 et 60-4 de la CEI.Il est
recommand d'utiliser un diviseur de tension rsistif, calibr avec prcision et un voltmtre de
crte, de prfrence un oscilloscope. Cependant, on peut accepter l'talonnage du systme de
mesurage
l'clateur
sphre, selon la Publication 52 de la CEI. L'erreur
sur
la mesure de la valeur
de la tension de crte devrait dans ce cas tre connue et ne pas dpasser 3%.
4.4 Conception de la cellule d'essai
4.4.1 La cellule se compose d'un rcipient contenant 'clateur vertical comme illustr titre d'exemple
la figure 1, page 26. Le volume du liquide dans cette cellule est de l'ordre de 300 ml.
Les
parties mtalliques doivent tre limites aux lectrodes et
leurs supports.
4.4.2 I1 est conseill de concevoir la cellule d'essai de faon faciliter son dmontage et permettre un
nettoyage
fond. Ses dimensions devraient lui assurer une tension de contournement d'au moins
250
kV.
4.4.3
Les
matriaux constituant la cellule ont une rigidit lectrique leve, sont thermiquement stables
jusqu' des tempratures de 80 OC compatibles avec le liquide isolant en essai et rsistants aux
solvants et produits de nettoyage ordinairement utiliss pour ces liquides.
4.4.4 L'clateur est compos de deux lectrodes formant un systme rglable pointe-sphre. L'lectrode
sphrique est en acier poli et peut tre une bille de roulement de 12,5 mm
13 mm de diamtre.
Cette bille est fixe l'aide d'un aimant. L'lectrode-pointe est une aiguille de phonographe
d'extrmit conique et dont le rayon de courbure est de l'ordre de 40 pm 70 pm. I1 est conseill de
vrifier au microscope la forme de l'aiguille etce rayon de courbure; l'annexeB donne une mthode
de dtermination du rayon de courbure.
5. Echantillonnage du liquide
Les
chantihons du liquide isolant
essayer doivent tre prlevs suivant la Publication 475 de
la CEI.
6. Prparation et entretien de la cellule
6.1 Nettoyage de la cellule
Toutes les pices de la cellule, y compris l'lectrode sphrique et l'aiguille de phonographe sont
dgraisses
l'heptane pur de qualit pour analyse, laves avec un dtergent et rinces abondam-
ment l'eau chaude du robinet puis
l'eau distille.
I1 convient de scher les pices l'air comprim dshydrat et dshuil et de les conserver dans un
dessiccateur jusqu' leur emploi.
6.2 Emploi quotidien
La cellule prpare comme indiqu au paragraphe 6.1 est prte pour les essais. Avant d'essayer un
Tant que les essais sont effectus
sur
le mme chantillon, il suffit de rincer la cellule avec le
nouvel chantillon, refaire le nettoyage prcdent en utilisant un solvant convenable.
liquide, entre chaque remplissage.
7. Prparation de l'essai
7.1 Rincer compltement la cellule d'essai et les lectrodes avec l'chantillon du liquide.La remplir
lentement en s'assurant qu'il n'y a pas de bulles d'air. Laisser reposer le liquide au moins 5 min
avant de procder
l'essai.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
13/30
897 O IEC 1987 - 11 -
4.3
Impulse voltage measurement
The impulse voltage measurement should be carried out as laid down by I EC Publications 60-3
and 60-4.An accurately calibrated resistive voltage divider and a crest voltmeter are recommended
in preference to an oscilloscope. However, calibration of the measuring system by sphere-gap in
accordance with IEC Publication 52 is acceptable. The error in measurement of the crest value of
the impulse voltage should be known and should not exceed 3%.
4.4
4.4.1
4.4.2
4.4.3
4.4.4
Test-cell design
The cell consists of a vessel containing a vertical gap as shown for example in Figure 1 , page 26. The
volume of liquid in this cell is of the order of 300
ml
Metal parts shall be restricted to electrodes and their supports.
The test-cell should be designed for ease of dismantlingand thorough cleaning. Dimensions should
ensure a flashover voltage of at least 250 kV.
Insulating materials used in the cell shall be of high dielectric strength, thermally stable for
temperatures up to 80
O C ,
compatible with insulating liquids to be tested, and resistant to solvents
and cleaning agents commonly used for these liquids.
The gap shall be composed of two electrodes forming an adjustable point-to-sphere configuration.
The spherical electrode shall be of polished steel and may consist of a bearing ball 12.5 mm to
13 mm in diameter. This ball is held in place by a magnet. The point electrode shall be
a
gramo-
phone needle, with a conical tip having a radius of curvature in the range 40 pm to 70 pm. The
shape af the needle and the radius of curvature should be checked using a microscope; AppendixB
gives a method for measuring the radius of curvature.
5.
Sampling of the liquid
Samples of the insulating liquid to be tested shall be taken in accordance with IEC Publi-
cation 475.
6. Preparation and maintenance of the cell
6.1
Cell cleaning
All parts of the cell, including the spherical electrode and gramophone needle, shall be de-greased
with reagent-grade heptane, washed with detergent, rinsed thoroughly with hot tap-water and then
with distilled water.
The parts should then be dried with oil-free dehydrated compressed air, and kept in a desiccator
until required.
6.2 Daily use
The cell prepared as described in Sub-clause 6.1 is ready for the tests. Before testing a new sample,
As long as the tests are applied to the same sample, rinsing out with the liquid between each filling
repeat the prescribed cleaning using an appropriate solvent.
is adequate.
7. Preparation of test
7.1 Rinse the cell and electrodes thoroughly with the sample liquid. Fill the test-cell, slowly, making sure
that there are no gas bubbles. Allow the liquid to settle for at least 5
min
before testing.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
14/30
I E C 8 9 7
8 7 =
48q489L O O B 9 8 7
'8 =
- 12 - 897
O CE1
1987
7.2 Eca rtem ent des lectrodes
Mettre les lectrodes n contact avec prcaution, contact que l'on vrifie
l'ohmmtre, puis
dplacer l'une des lectrodes de l'cartement voulu en utilisant une vis micromtrique, un systme
hlicodal ou une jauge d'paisseur. L'cartement des lectrodes doit tre ajust aux valeurs dfinies
au paragraphe 8.1.2, avec une tolrance de 0,l mm.
7.3 Mettre
la terre l'lectrode sphrique; la connexion doit tre aussi courte que possible.La tension de
sortie du gnrateur de choc est applique
l'lectrode-pointe; il faut viter avec soin d'avoir une
trop grande connexion.
7.4 I1 est conseill, au moment de l'essai, que la temprature de l'chantillon soit en quilibre avec ceiie
du local; cette temprature est convenable entre 15 C et30 C. Noter la temprature de l'essai.
8.
Procdures d'essai
8.1 Mthode
A -
Essai par chelons
8.1.1 . Principe
On applique des tensions de choc de foudre normal 1,2/50, de valeurs de crte croissantes,
l'chantillon de liquide, en utilisant un systme d'lectrodes pointe-sphre, jusqu'au claquage. On
effectue cinq mesures et leur moyenne est considre comme la tension de claquage au choc de
foudre du liquide essay.
La valeur initiale de la tension d'essai, l'accroissement de la tension e t l'cartement des lectrodes
dpendent de la valeur de la tension de claquage du liquide essay.
.
8.1.2 Procdure
a) Prparer la cellule d'essai selon l'article 7.
b)
A partir du tableau
I,
choisir la valeur initiale approprie
(
Ui) de la tension d'essai, l'chelon de
tension et l'cartement des lectrodes qui dcoulent de la tension de claquage espre
( U J ,
pour
l'cartement de 15 mm.
c) Appliquer un choc (de polarit choisie) la tension initiale choisie, puis augmenter cette tension
par chelons jusqu'au claquage. On doit appliquer un choc et un seul, chaque niveau de
tension, en attendant au minimum 1 min entre deux chocs successifs.
d La procdure dcrite aux points a),
b),
c) est rpte pour obtenir cinq valeurs de claquage du
liquide essay. Aprs chaque claquage, l'lectrode pointe est remplace et l'lectrode sphrique
change de position. Ensuite poursuivre suivant les paragraphes 7.1 et 7.2. L'lectrode sphrique
doit tre remplace tous les cinq claquages,
e) Pour que l'essai soit valide,
il
faut que l'chantillon essay supporte au moins trois niveaux de
tensions sans claquage. Si le claquage a lieu avant, refaire l'essai en commenant
une tension
initiale infrieure, de 5
kV
ou 10
kV
selon le cas.
l
Noter la valeur de crte prvue du choc au cours duquel le claquage s'est produit comme tant la
tension de claquage nominale.
g)
Si la tension de claquage d'un liquide en essai ne peut tre prvue, dterminer une valeur
approximative de
U
n suivant les points
a)
et
c),
pour une distance de 15 mm, une tension
initiale de 50
kV
et un chelon de tension de 10
kV.
Poursuivre ensuite du point a) au
point
8.
Si, 15 mm, l'on ne peut obtenir un claquage une tension infrieure de contournement de la
cellule (environ 250 kv), diminuer l'cartement de l'clateur jusqu' 10 mm ou 5 mm si
ncessaire.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
15/30
I E C 8 9 7
897 O IEC 1987 - 13 -
7.2
7.3
7.4
Electrode spacing
Gently set the electrodes in contact, checking contact with an ohmmeter; then displace one of the
electrodes to the desired spacing value using a dial micrometer, a helical device or a thickness gauge.
The gap spacing shall be adjusted to the values defined in Sub-clause 8.1.2, with a tolerance of
0.1 mm.
Earth the spherical electrode; the connection shall be as short as possible. The impulse generator
output shall be applied to the point electrode and care must be taken to avoid too large a connection
The temperature of the sample when tested should be the same as the temperature of the test-room;
a room temperature between 15 C and 30 C is appropriate. Record the test temperature.
loop.
8. Test procedures
8.1 Method A-S tep test
8.1.1
Principle
1.2/50 standard lightning impulse voltages of increasing crest value are applied to the liquid
specimen using a point-to-sphere electrode system until breakdown occurs. Five measurements are
carried out and their average is taken as the lightning impulse breakdown voltage of the liquid
tested.
The initial value of the test voltage, the voltage step and the electrode spacing depend on the
breakdown voltage value of the liquid tested.
8.1.2 Procedure
Prepare the test-cell as described in Clause 7.
From Table I, select the appropriate initial value of the test voltage
(Vi)
voltage step and gap
spacing, based on the expected breakdown( U J at 15 mm gap spacing.
Apply one impulse (of the selected polarity) at the initial selected voltage and then increase the
voltage in steps until breakdown occurs. One impulse shall be applied at each voltage level,
allowing a minimum of 1 min. between two successive impulses.
The procedure as described in Itemsa), b),c) shall be repeated until five breakdown values have
been obtained for the liquid tested. After each breakdown the point electrode is changed and the
sphere electrode rotated, then follow Sub-clause 7.1 and 7.2. The sphere electrode shall be
changed every five breakdowns.
For the test to be valid, the test sample shall withstand a minimum of three levels before
breakdown occurs. If breakdown occurs before, repeat the test with a lower initial voltage, 5 kVor
10 kV according to the case.
Note the prospective crest value of the impulse during which the breakdown occur as the nominal
breakdown voltage.
When the breakdown voltage of a liquid under test cannot be anticipated determineU, following
Itemsa) and e), using a gap of 15 mm, a starting voltage of 50 kV and a voltage step of 10 kV. Then
continue as in Item a) toJ).
If breakdown at 15 mm cannot be obtained below the flashover voltage of the cell (about 250 kv)
decrease the gap spacing to 10 mm
or,
if necessary, 5 mm.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
16/30
I E C
8 9 7 87 4 8 4 4 8 9 1 0089389
I
W
- 14 - 897
O CE1
1987
Tension estime 15 mm (UefiV))
Distance (mm)
Tension initiale (ui(kV)
Echelon de tension (W
TABLEAU
Slection de
la
tension initiale et de la distance
50
u.
=G 100 100 < U,
< 250
U,>
250
25
0,l
15
f
0,l
10
*
0,l
1,s U,- 5 u, - 50 150
5 5 10
Polarit des cho cs
ngative
positive
8.1.3
Fidlit
~
r( )
R
9'0)
7 10
15 30
La fidlit d'une mthode d'essai est caractrise par sa rptabilit
r
et sa reproductibilit
R
(voir Norme
I S 0
5725).
Le
tableau
II
donne ces valeurs dans le cas particulier d'huiles isolantes
minrales, essayes suivant la mthode
A.
'
Notes 1 - Les valeurs de
I'
et R sont exprimes en pourcentage de la tension de claquage
moyenne.
2 - Les valeurs donnes dans le tableau
II
sont dtermines partir de rsultats
d'essais mens sur trois huiles isola ntes minrales par sept laboratoires.
Si la mthode est correctementapplique, il
y
a une probabilit de 5% pour que la darence entre
deux rsultats individuels (voir note) obtenus
partir de deux essais effectus sur la mme huile,
dans les mmes conditions (mme oprateur, mme appareil, mme laboratoire et court intervalle
de temps), puisse excder 7% de U dans le cas de chocs ngatifs et 15% de U dans le cas de chocs
positifs,
U
tant la moyenne des deux rsultats.
Si deux rsultats individuels sont obtenus partir d'essais mens sur la mme huile, mais sous
diffrentes conditions (diffrents oprateurs, diffrents appareils, diffrents laboratoires),il y a une
probabilit de 5% pour que
la
diffrence entre deux rsultats puisse excder
10%
de Udans lecas de
chocs ngatifs et 30% de
U
dans le cas de chocs positifs.
Si la diffrence entre les deux rsultats dpasse les valeurs donnes au tableau
II,
une interven-
tion supplmentaire est souhaite, par exemple vrifier l'appareillage et rpter les essais.
Note. - Un ((rsultat indiv idue l)) est la mo yen ne de cinq te nsion s de claquage ainsi qu'il est spcifi dans le para-
graphe
8.1.1.
8.2 Mthode B - Test
progressif
8.2.1
Principe
L'exprience montre que, lorsque l'on applique
la cellule d'essai un choc de foudre de valeur de
crte proche de la tension de claquage mesure suivant la mthode
A,
un claquage peut ou non se
produire. On est ainsi conduit
introduire la notion de probabilit de claquageP, onction de
U
mais de valeur inconnue.
Le
est progressif permet de comparer cette probabilit de claquage une
valeur arbitraire
Po
et de tester l'hypothse:
H o :P
Po.
Pour tenir compte de considrations pratiques, on se fixe une valeur
P ,
infrieure
Po
et
un risque d'erreur a, tels que la probabilit de rejeter
Ho,
alors que P < P l , soit infrieure ou
gale
a.
De mme, on se fixe une valeur P2 suprieure
Po
et un risque d'erreur
p
tels que la probabilit
d'accepter Ho,alors que P z P2, soit infrieure ou gale
p.
A5. SoitL le rapport de vraisemblance
L
=
/LI
oLIest la probabilit d'obtenir un certain ensemble
de valeurs observes quand P = P1 et la probabilit d'obtenir un certain ensemble de valeurs
observes quand P
=
P2.
Le
test progressif consiste
calculer L
chaque observation et suivre les rgles de dcision
suivantes:
Si L < A , on accepteHo
i
L
z=
,
on rejette
HO
Si A
< L l
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
23/30
897 O IEC 1987 - 21 -
A4. Let Po be an arbitrary value. We wish to test the hypothesisHo: P < Po against the alternative
hypothesisH l
:
P > Po at a value U of the test voltage applied.
For practical considerations a valueP1 lower than Po and an error riska are fured such that the
probability of rejectingHo when P =s P1 is lower or equal to a.
Likewise a value P2 higher than Po and an error
risk
p
are fixed such that the probability of
accepting
Ho
when P
P2 is lower or equal to p. ,
A5. Let L be the likelihood ratio defined asL = L2/L1 hereLI s the probability of obtaining a set of
observed values with P
=
Pl and
Lz
is the probability of obtaining a set of observed values with
P
=
Pz.
The sequential test consists in calculatingL at any stage of the experiment and in taking the
following decision rules:
If L < A , Ho is accepted
If
L R,
Ho
is rejected
If A < L < R, the experiment is continued by making an additional observation.
A and R are chosen in such a way that the probability of rejectingHo when P
=
Pl is
a
and the
probability of acceptingHo when P
=
P2 is p.
An approximate calculation shows that:
A = p / ( l - a )
R = ( l
- P ) / a
To summarize,i f P
=s
l the probability of rejectingHo is always lower or equal toa and i f P P 2
the probability of acceptingHo is always lower or equal top.
A6. The probability
LI
that
dn
breakdowns would occur in
n
impulse applications with
P
=
Pl
is:
The probability that d breakdowns would occur in n impulse applications withP = Pz is:
Therefore the likelihood ratio is:
L
=
Pzdn 1 - Pz)n-dn P , q l p -d n
Suppose that after
n
impulses the conditionsL R, la conditionL
z
R
est remplie et l'hypothse nulleHoest rejete. En consquence, on
peut appeler
R,
ndice de refus.
A8. Dans le plan de coordonnes
n
d, le rsultat du test aprsn chocs, peut tre reprsent par le point
( n , d, . A , et
R,
(voir (1) et (2) ci-dessus) sont les quations de deux droites parallles(Di)et (DJ,
respectivement, qui divisent le plan en trois zones (voir graphe de dcision, figure 2, page 27).
Si le point
(n ,
d, se trouve dans la zone infrieure
la droite
(Di),
HO st accept etsi cepoint est
dans la zone au-dessus de la droite(Il2), o est refus. Si le point se trouve entre les deux droites,
aucune dcision ne peut tre prise et on applique un autre choc.
A9. Le
graphe de dcision prsent
la figure 2 est un exemple obtenu
partir des valeurs
suivantes
Po
=
10%;Pi
=
5 ;
P2=
15%;
a =
5% et
=
1%.
Alo . A la diffrence du test statistique classique, le test progressif quivalent n'exige pas qu'un nombre
d'essais dtermin l'avance soit obtenu.
Le
nombre d'essais est une variable alatoire qui est, en
moyenne, plus petit que le nombre d'essais qu'exigerait le test Statistique classique quivalent.
De plus, on dmontre que la probabilit que le test progressif se poursuive indfiniment est nulle.
Cependant, pour ne pas prolonger l'essai, il est possible de furer une limite au processus en appli-
quant soit une rgle de troncature, soit ensuivant la dcision du paragraphe 8.2.2.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
25/30
897 O IEC 1987
Let
- 23 -
When
d,
-
7/25/2019 IEC 897 (1987)
26/30
I E C
8 9 7
87 M 4844891
0089399
4
-
24 -
ANNEXE
B
897
O CE1
1987
MESURAGE DES RAYO NS DE COUR BURE DES AIGUILLES
B
1. La prsente annexe dcrit une mthode pour dterminer le rayon de courbure de l'lectrode pointe
l'aide d'un microscope mtalographique.
La
figure
3,
page 27, donne le schma de montage du systme optique.
La lumire mise par la source lumineuse (S) du microscope est renvoye par un jeu de miroirs
45 M)
sur l'objet examiner(A). L'image est ensuite forme, travers les objectifs
(L1
,
L2)
sur un
verre dpoli (D). Les rgiages sont faits de telle sorte que le grossissement final soit de 1000.
A
l'aide d'une chelle gradue en millimtres, mesurer directement sur le verre dpoli
(D)
la
Pour plus de prcision, faire deux mesures correspondant
deux cordes de valeurs dif-
flche u )correspondant la corde
(b).
frentes.
La valeur du rayon de courbure est obtenue par l'expression:
R =
[
()*
+ u21
/ 2 a
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
27/30
897
O
IEC 1987
- 25 -
APPENDIX
B
MEASUREMENT OF RADIUS OF CURVATURE
OF
NEEDLES
B1. This appendix describes a method for determining the radius of curvature of the point electrode by a
metallographic microscope.
Figure
3,
page 27, gives the schematic diagram
of
the optical system.
The light emitted by the source
of
light of the microscope S ) is reflected by a set of mirrors at an
ande
of
45 (M) on the object (A) to be examined. The image is then projected, through lenses (Ll,
L2),
on
a ground giass plate (D). Settings are made so that the object is finally magnified a thousand
times.
Using a scale graduated in millimetres, measure directly on the ground giass plate (D) the
sagitta
a)
corresponding to chord
( b ) .
For greater accuracy, make
two
measurements corresponding to two chords of different
values.
The value of the radius of curvature is obtained from the exmession:
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
28/30
I
I E C 897 87
W
484q873 0089203
9
W
-
26
-
897 O
CE
1987
FIG.1.- Systme dlectrodes pointe-sphr e pour essais de choc de liquides isolants.
Point-to -spher e electrod e system for impulse strength of insulating liquids.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
29/30
897
O IE C 1987
-.
-.
-.
IO-.
9--
8--
7 - -
6- -
5--
4 -.
3--
2 -.
I --
O -.
Nombre de dcharges disruptives
Number of disruptive discharges
d n t
O
I
5 10 15
Dtail
A
Detail
20 25
30
35
- 27 -
Po = 10 Pl = 5 P 2 = 15
a = 5
s
=
0,092
h i =
-3,76
h2 =
2.47
p
=
1
40
45 50 55 60 65 70 75 80 85
n
Nombre de chocs
Impulses number
119/87
rayon de courbure
radiusof curvature
flche
sagitta
corde
chord
R =
a =
b
FIG.
2.- Graphe de dcision.
Ruling graph.
Image (voir dtail A )
(see detail
A i
f
A-
LI?
t
12 187
=
source lumineuse
source of light
L = objectif grossissement 32x
lens magnification 32 x
miroir
mirror
= .
L2 =
objectif grossissement 18x
lens magnification 18x
verre dpoli
A =
iguille de phonographe D =
gramophone needle ground glass
FIG.
3.- Mesurage du rayon de courbure des aigu illes.
Measurement of radius of curvature of needles.
International Electrotechnical ommissionPYRIGHT International Electrotechnical Commissioncensed by Information Handling Services
-
7/25/2019 IEC 897 (1987)
30/30
Publications de Ia C E 1 prpares
par le Comit d'Eudes no 10
74 (1963)
156 (1963)
247 (1978)
296 (1982)
376 (1971)
376A (1973)
3760 (1974)
422 (1973)
465 (1974)
465A (1977)
474 (1974)
475 (1974)
480 (1974)
567 (1977)
Mthode po ur valuer la stabilit
l'oxydation des huiles
isolantes.
Deuxime dition 1963 comprenanf les modifications no 1
(1973) et no 2 (1974).
Mthode pour ladtermination de a rigidit lectrique des
huiles isolantes.
Mesure de a permittivit relative, du facteur de dissipation
dilectrique e t d e la rsistivit (en courant continu) des
liquides isolants.
Spcification des huiles minrales isolantes neuves pour
transformateurs et appareillage de connexion.
Spcifications et rception d e l'hexaluorure de sou fre
neuf.
Premier complment: Section treize: Tau x d'huile m in-
rale.
Deuxime complment : Article 26.
Guide pour la maintenance et la surveillance des huiles
isolantes en service.
Dilectriques liquides neufs base d'hyd rocarbures (autres
que les huiles minrales pour transformateurs et appareil-
lage de coupure).
Premier complment.
Mthode d'essai pour la stabilit
l'oxydation des huiles
minrales inhibes.
Mthode d'chantillonnage des dilectriques liquides.
Guide relatif a u con trle de l'hexafluorure de soufre (SF,)
prlev sur le matriel lectrique.
Guide pour le prlvement des gaz et de l'huile dans le
matriel lectrique rempli d'huile et pour l'analyse des gaz
libres et dissous.
588
:
- Askarels po ur transformateurs et condensateurs.
588-1 (1977)
588-2 (1978)
588-3 (1977)
588-4 (1979)
588-5 (1979)
588-6 (1979)
590 (1977)
599 (1978)
628 (1985)
666 (1979)
733 (1982)
813 (1985)
814 (1985)
867 (1986)
897 (1987)
Premire partie: Gnralits.
Deuxime partie: Mthodes d'essai.
Troisime partie: Spcifications pour askarels neufs.
Quatrime partie: Gu ide pour la m aintenance des askarels
dans les transformateurs.
Cinquime partie: Essai liminatoire pour dterminer la
compatibilit des matriaux avec
les
askarels pour trans-
formateurs.
Sixime partie: Essai liminatoire pour dterminer
les
effets des matriaux sur les askarels pour condensateurs.
Dtermination de la teneur
en
hydrocarbures aromatiqu es
des huiles isolantes minrales neuves.
Interprtation de l'analyse des gaz dans les transformateurs
et autres matriels lectriques remplis d'huile, en service.
Gassing des isolants liquides sous contrainte lectrique e t
ionisation.
Dtection et dosage d'additifs antioxydants spcifiques
prsents dans les huiles isolantes.
Dosage de l'eau da ns
les
huiles isolantes, dans les papiers et
cartons imprgns d'huile.
Mthode d'essai pour valuer la stabilit l'oxydation d es
dilectriques liquides
base d'hydrocarbures.
Dosage de 'eau dans les dilectriques liquides par titration
coulomtnqu e de Karl Fischer automatique.
Spcifications pour isolants liquides neufs base d'hydro-
carbures aromatiques de Synthese.
Mthodes de dtermination de la tension d e claquage au
choc d e foudre des liqu ides isolants.
I E C publications prepared
by Technical Committee
No. 10
74 (1963)
156 (1963)
247 (1978)
296 (1982)
376 (1971)
376A (1973)
376B (1974)
422 (1973)
465 (1974)
465A (1977)
474 (1974)
475 (1974)
480 (1974)
567 (1977)
Method for assessing the oxidation stability of insulating
oils.
Second edition 1963 incorporating Amendments No. 1
(1973) and No. 2 (1974).
Method for the determin ation of the electric strength of
insulating oils.
Measurement of relativ e permittivity, d ielectric dissipation
factor and d.c. resistivity of insulating liquids.
Specification for unused mineral insulating oils for trans-
formers and switchgear.
Specification and acceptance of new sulphur hexa-
fluoride.
First supplement: Section Thirteen: Mineral oil content.
Second supplem ent: Clause 26.
Maintenance and supervision guid e for insulating oils in
service.
New
liquid hydrocarbon dielectrics (other than mineral
transformer an d switchgear oils).
First supplement.
Test method for oxidation stability of inhibited mineral
insulating oils.
Method of sampling liqu id dielectrics.
Guid e to th e checking of sulphur hexafluoride (SFs) taken
from electrical equipment.
Guid e for the sampling ofgases and oil
from
oil-fuled elec-
trical equip ment an d for the analysis of free and dissolved
gases.
588: - Askarels for transformers and capacitors.
588-1 (1977)
588-2 (1978)
588-3 (1977)
588-4 (1979)
588-5 (1979)
588-6 (1979)
590 (1977)
599 (1978)
628 (1985)
666 (1979)
733 (1982)
813 (1985)
814 (1985)
867 (1986)
897 (1987)
Part
:
General.
Part 2: Test methods.
Part 3: Specifications for new askarels.
Part 4: Guide for maintenance of transformer askarels in
equipment.
Part
5:
Screening test for com patibility of materials and
transformer askarels.
Part 6: Screening test for effects of materials
on
capacitor
askarels.
Determinationof th e aromatic hydrocarbon con tent of new
mineral insulating oils.
Interpretation of the analysis of gases in transformers and
other oil-filled electrical equipm ent i n service.
Gassing of insulating liquids under electrical stress and
ionization.
Detection and d etermination of specified antioxidant addi-
tives in insulating oils.
Determination of water in insulating oils, and in oil-
impregnated paper an d pressboard.
Test method forevaluating theoxidationstability ofh ydro-
carbon insulating liquids.
Determination of water in insulating liquids by automatic
coulometric Karl Fischer titration. .
Specifications for unused insulating liquids based on
syn
thetic arom atic hydrocarbons.
Methods for the determination of the lightning impulse
breakdown voltage of insulating liquids.
Publication897