Page1
Laboratory Testing and Numerical Simulation of a Strip Footing on Geosynthetically
Reinforced Loose Sand
Jiunnren Lai Associate Professor, Department of Construction Engineering, Chaoyang University of Technology, 168 Jifong E. Rd., Wufong District, Taichung City, Taiwan 41349. Bo-Huan Yang Ph.D. Candidate, Department of Construction Engineering, Chaoyang University of Technology, 168 Jifong E. Rd., Wufong District, Taichung City, Taiwan 41349.
Abstract
The objective of this paper is to study the bearing capacity and loading behavior of strip
footings on geosynthetically reinforced loose sand. Laboratory loading tests were conducted on
a rigid steel strip footing in a 0.9m x 0.9m x 1.0m sand box. Woven geotextile was used as
reinforcement material. A finite difference program was used to simulate the load-settlement
behavior of this footing. Two constitutive (Mohr-Coulomb and Double-Yield) models were
utilized for the loose sand. Direct shear tests were performed to obtain the parameters needed
for numerical simulation. The unreinforced ultimate bearing capacity obtained from this study
ranges between theoretical values calculated by assuming general and local shear failure
conditions. The bearing capacity predicted by these two soil models match with values
obtained from sand box tests. However, the Double-Yield model outperforms the traditional
Mohr-Coulomb model in simulating the loading behavior of this strip footing.
Keywords: bearing capacity, geotextile, Double-Yield model
Introduction
The bearing capacity of shallow foundation on weak soil reinforced with geosynthetics is one
of the most important subjects in geotechnical engineering. A great number of investigators
Page2
have been devoted their research efforts into this issue. In 1975, Binguet and Lee [1] reported
results of bearing capacity tests of footings on soil bed reinforced with galvanized steel strips
and defined qu,reinforced/qu,unreinforced as Bearing Capacity Ratio (BCR) to quantify the benefit of
reinforcement. For a better understanding of how the reinforced soil performs, several
researchers have been investigated the failure mechanism between soil and reinforcement
material [2-4]. The failure mechanism and bearing capacity of reinforced soil subjected to
footing load were studied by Binguet and Lee [5], Schlosser and Elias [6], Huang and Tatsuoka
[7], Huang and Menq [8], Yamamoto and Kusuda [9], and many others. For designing purpose,
some investigators have performed numerical simulations using finite element (FEM) method
[10-13] or finite difference program [14, 15] to predict the ultimate bearing capacity of
reinforced soil and to optimize the arrangement of reinforcement elements beneath the footing.
On the other hand, researchers such as: Fragaszy and Lawton[16], Verma and Char [17], Khing
et al. [18], Omar et al. [19], Dash et al. [20], Ghosh et al. [21], and Abu-Farsakh et al. [22,23]
have conducted laboratory tests or field observations to obtain the optimum arrangements for
various reinforcement materials. For single layer of reinforcement, they found the optimum
reinforcement length is about 4~7 times footing width (B), and the optimum depth ratio ranges
between 0.25B and 0.4B. Sharma [24] and Chen and Abu-Farsakh [25] have developed
analytical solutions to estimate the ultimate bearing capacity of strip footings on reinforced soil.
However, most of these studies have been focused on the ultimate bearing capacity of the
reinforced soil under general shear failure condition, which is reasonable for dense sand. For
cases when heavy construction equipment is not available or the compaction quality is not as
good as expected. The sand will be in loose condition and general shear failure may not occur.
Therefore, in this paper, a series of laboratory tests were conducted to study the loading
behavior of a reinforced strip footing in loose sand. The load-settlement curves of these tests
were simulated using a commercial finite difference program. Bearing capacity and loading
Page3
behavior of the strip footing from sandbox test and numerical simulation were compared. The
effects of various designing parameters, such as depth, length, and layer arrangement of the
reinforcement on the bearing capacity were also investigated.
Experimental Methods and Material Properties
Testing Equipment
A series of sandbox tests were conducted to study the loading behavior of strip footings on
reinforced loose sand. A schematic drawing of the testing equipment is shown in Fig. 1. It
consists of a test cell, a reaction frame with hydraulic ram, a hydraulic pump, load and
displacement sensors, and a data acquisition system. The dimensions of the test cell are 0.9m x
0.9m x 1.0m, respectively. The test cell was prepared by pouring dry sand from a #10 sieve at a
constant falling height of 0.3m. This sample preparation method can yield uniform sand with a
density of about 1410 kg/m3 (relative density, Dr = 12.4%) and a friction angle, , of about 34
degrees. A hydraulic loading system was used to apply normal force to a 0.85m x 0.10m x
0.05m rectangular steel plate. A load cell was used to measure the applied force while two
linear variable differential transformer (LVDT) were used to measure the settlement of the
footing.
Material Properties
The sand used in this study is an alluvium sand commonly used as fine aggregate for concrete.
Table 1 shows the properties of this sand. Its fine content (% finer than 0.075mm) is less than
5%. The Uniformity coefficient (Cu) and Coefficient of gradation (Cc) are 2.97 and 0.94,
respectively. It can be classified as poorly graded sand (SP) according to the Unified Soil
Classification System (USCS). A woven geotextile (model PP 70/70) was used as
reinforcement material. The properties of this geotextile are shown in Table 2.
Page4
Numerical Simulations
Soil Model
A commercial finite difference program - Fast Lagrangian Analysis of Continua (FLAC) was
used to perform the numerical simulation. The software provides a variety of soil model such
as the traditional elastic-plastic Mohr-Coulomb model as well as the Double-Yield model. In
addition to shear (line A-B in Fig. 2) and tensile yield function (line B-C in Fig. 2) of the
Mohr-Coulomb model, a volumetric yield function (Fig. 3) is also considered in the
Double-Yield model. In this model, the permanent volume change (plastic strain) induced by
change in normal stresses is taken into account [26]. The volumetric yield surface, also known
as “cap”, is defined by the cap stress (pc), and is related to the plastic volumetric strain. When pc
increases, the soil becomes denser, and its stiffness also increases. Therefore, it is suitable to
simulate the volume change behavior of reinforced soil. As shown in Fig. 3, the stiffness of soil
(i.e., the current bulk modules, Kc) is a function of cap stress and plastic volumetric strain, and
can be calculated by the following equation:
cc p
V
dpK R
d (1)
where R is the stiffness ratio and is equal to p eV V , while e
V and pV are elastic and plastic
volumetric strain, respectively. In FLAC, R is a parameter that should be input by the user. In
addition, FLAC calculates the current shear modules, Gc, by the following equation:
cc
KG G
K (2)
Where K and G are the initial (maximum) elastic bulk modulus and shear modulus,
respectively.
In the Double-Yield model, the shear yield function and plastic potential function are
controlled by mobilized friction angle (mob) and dilation angle () respectively. The shear
yield is a function of mobilized friction angle (mob) and plastic shear strain (p) and can be
Page5
obtained from plane strain tests or direct shear tests using the following equations:
1 yxmob
yy
Tan
(3)
max
yx yxp d d
G G
(4)
Where yx and yy are shear stress and normal stress, G and Gmax are current and maximum
(initial) shear modulus, dyx is the incremental shear stress, respectively.
The dilatancy angle controls the amount of plastic volumetric strain developed during
plastic shearing and can be obtained from a plane strain test using the following equation [27]:
1 1 3
1 3
p p
p pSin
(5)
where 1p and 3
p are the major and minor principle plastic strain increment, respectively. It
can also be obtained from the vertical displacement-shear displacement curve of a direct shear
test using the following equation [28]:
1 1yy
yx
d dyTan Tan
d dx
(6)
Wheredy and dx are the incremental vertical and shear displacement, respectively.
When using the Double-Yield model, in addition to the density, peak friction angle, shear
and bulk moduli needed for the Mohr-Coulomb model, a stiffness ratio, a table defining
volumetric strain (v) vs. normal stress (n, a second table defining mobilized friction angle
(mob) vs. plastic shear strain (p), and a third table defining dilation angle () vs. plastic shear
strain (p) are also needed.
Reinforcement Model
A cable element was used to simulate the behavior of reinforcement (geotextile). In FLAC, the
cable is assumed to be divided into a number of segments of length, L, with nodal points
Page6
located at each segment end. The axial behavior of conventional reinforcement systems is
assumed to be governed entirely by the reinforcing element itself. In formulation, the axial
stiffness is described in terms of the reinforcement cross-sectional area (A) and Young’s
modulus (E). The shear behavior of the reinforcement/medium interface is represented as a
spring-slider system located at the nodal points, and is described numerically by the interface
shear stiffness (Kbond) using the following equation:
( )Sbond c m
FK u u
L (7)
where:
Fs = shear force that develops in the grout
(i.e., along the interface between the cable element and the grid);
Kbond = grout shear stiffness;
uc = axial displacement of the cable;
um = axial displacement of the medium (soil or rock); and
L = contributing element length.
The maximum shear force developed in the interface, per length of element, is a function of the
cohesive strength and the stress-dependent frictional resistance of the interface. The following
relation is used to determine the maximum shear force:
max
tan( )sbond c friction
FS S perimeter
L (8)
where:
Sbond = intrinsic shear strength or cohesion;
’c = mean effective confining stress normal to the element;
Sfriction = friction angle; and
perimeter = exposed perimeter of the element.
The mesh used in numerical simulation is shown schematically in Fig. 4. The element size
Page7
is 1cm x 1cm. For a strip footing, it is reasonable to assume the soil is subjected to plane strain
condition. Because of symmetry, only the right-half of the test cell was simulated. A roller
boundary was used for the left boundary (axis of symmetry), while a pinned boundary was used
for the right and bottom boundaries. Since a thick steel plate was used as strip footing in the
sandbox test, the settlement of soil underneath the footing should be uniform. Therefore, a
constant rate of deformation was assigned to the grids right beneath the footing to simulate the
application of footing load. Unbalance forces of all grids were calculated and redistributed for a
small time step until it reaches equilibrium. The stress applied on the footing was obtained by
summing the nodal force in the vertical direction of grid points beneath the footing, than
divided by half the width of the footing.
Results and Discussions
Parameters for Sand
Table 3 shows properties of the loose sand used in numerical simulation. Oedometer test and
direct shear test were performed to obtain the parameters (properties) needed for numerical
simulation. Stress-volumetric strain curve from the oedometer test is shown in Fig.5. The shear
modulus (G) and bulk modulus (K) are calculated using constrained modulus (M) obtained
from the first load increment and assuming a Poisson’s ratio () of 0.35 by the flowing two
equations:
(1 2 )
2(1 )
MG
(9)
(1 )
3(1 )
MK
(10)
The stiffness ratio (R) obtained from the 1st and 2nd loading-unloading cycles are 5.3 and 5.7,
with an average value of 5.5. The stress-strain data in Fig. 5 were also used as the input table of
volumetric strain (v) vs. normal stress (n) relationship in the Double Yield model.
Page8
The shear stress (yx) vs. shear displacement (dx) curves from three direct shear tests are
shown in Fig. 6. The cohesion intercept, c, and angle of internal friction, peak, obtained from
these tests are 0 kPa and 34.4o, respectively. For each data point in Fig. 7a, the yx/y value was
used to calculate the ordinate (mob) of shear yield function using Eq. (3), and the shearing
displacement (dx) value was used to calculate the abscissa (p) of shear yield function using Eq.
(4). Similarly, the vertical displacement (dy) and the shearing displacement (dx) in Fig. 7b were
used to calculate the dilation angle () of the plastic potential function using Eq. (6). These two
functions are shown in Fig. 8 and Fig. 7b and were used as input table for the Double Yield
model in numerical simulation. Negative values of dilation angle were obtained (Fig. 7b)
because the sand was prepared in loose condition and is expected to have contractive behavior
during shear.
Parameters for Reinforcement
Table 4 shows the properties of geotextile used in numerical simulation. The elastic (Young’s)
modulus was calculated by using the tensile strength at 2% elongation in the cross direction.
The interface parameters (Kbond and Sbond) were obtained from previous pullout tests. The
interface friction angle (interface) was assumed to be equal to 1/3 of the peak of the loose sand, a
typical reduction factor that is commonly used for the interface friction angle between soil and
retaining structures. Parameter study indicated that the bearing capacity is influenced mostly
by Kbond. The interface friction angle (1/3~1 of soil-soil) has minimum effect on the bearing
capacity.
Unreinforced Footing
In order to validate the soil models used in this study, numerical simulations were performed
using the Mohr-Coulomb model and the Double Yield model. Results from the numerical
simulation are then compared with results from laboratory testing. Figure 9 shows the tested
and simulated load-settlement curves, together with the theoretical ultimate bearing capacity
Page9
calculated using Terzaghi’s equation. It can be seen that the ultimate bearing capacity from the
two sandbox tests are between the theoretical values by assuming general and local shear
failure. This seems reasonable because the sand was prepared under loose condition and
general shear failure might not occur thus resulted a lower value of ultimate bearing capacity.
Although the two soil models yield about the same ultimate bearing capacity and match the test
result, the Double Yield model outperforms the Mohr-Coulomb model in simulating the
loading behavior of the unreinforced strip footing. Therefore, only the Double Yield model was
used in simulating the reinforced footing.
Effects of Design Parameters on the Bearing Capacity
Both numerical simulation and laboratory test were performed to study the effects of design
parameters such as buried depth and reinforcement length on the bearing capacity. Comparison
between simulated and tested load-settlement curves of footing with single layer of
reinforcement are shown in Fig.10. It can be seen that the simulated curve matches the tested
curve reasonably well. The effects of buried depth (for a constant length of 6B) and
reinforcement length (for a constant depth of 0.4B) on the bearing capacity using single layer of
reinforcement from numerical simulation are summarized in Figs. 11(a) and 11(b). The
optimum buried depth and reinforcement length are 0.5B and 5B, respectively. For a given
buried depth or reinforcement length, the BCR increases as the normalized settlement (s/B)
increases. Because the stiffness of geotextile is relatively lower than the other geosynthetics
such as geogrids or geonets, higher deformations are required for the geotextile to mobilize its
tensile strength.
The simulated and tested BCR at various buried depths and reinforcement length are
compared in Fig. 12 and Fig.13 at various s/B. At 20% of s/B, the maximum BCR are 1.46 (test)
and 1.32 (simulation), the optimum buried depth are 0.4B (test) and 0.5B (simulation), and the
optimum reinforcement length are 4B (test) and 5B (simulation), respectively. The curves
Page10
obtained from numerical simulation are smoother than those of sandbox test. Since the width of
the footing is only 10cm, the variations in buried depth are very small. It is very difficult to
place the reinforcement at the right location. Furthermore, the sand was test under very loose
condition (Dr = 12.4%), the differences in bearing capacity are only a few kPa. Therefore, more
scatter within the test data can be expected. Although the simulated curves do not match with
the tested curves very well, the trends are very similar. And, the difference in the optimum
buried depth and reinforcement length obtained from numerical simulation and sand box test is
small.
The effectiveness of enhancing the bearing capacity of the footing with additional layer of
reinforcement and its optimum arrangement were also studied. Two different configurations
were compared. The first configuration is arranging the first layer of reinforcement at a buried
depth of 0.4B, while allocating the second layer 0.2B above it (i.e., d = -0.2B). In contrast, the
second configuration is arranging the second layer 0.2B beneath the first layer (d = 0.2B). The
reinforcement lengths are all kept at 3B. Comparison of the effectiveness of these two
configurations is shown in Table 5. Under the same reinforcement arrangement, the BCR
obtained from numerical simulation are slightly lower than values obtained from sand box test.
Nevertheless, the BCR of configuration 1 (d = -0.2B) are all higher than configuration 2 (d =
0.2B), from both numerical simulation and sandbox test. At 20% of s/B, the BCR only increase
slightly (1.46 to 1.55) from sandbox test, but more significant (1.23 to 1.39) from numerical
simulation.
Conclusions
This paper investigates the behavior and effectiveness of a strip footing reinforced with woven
geotextile through sandbox testing and numerical simulation. Based on the results of this study,
the following conclusions can be drawn:
Page11
(1) The ultimate bearing capacity obtained from both sandbox test and numerical simulation is
lower than the value calculated using Terzaghi’s equation, indicates that general shear
failure of the footing does not occur.
(2) The Double Yield model is very suitable in simulating the behavior of loose sand. The
procedures used in study to obtain the parameters for the Double Yield model are also
appropriate.
(3) With single layer of reinforcement, there is a 32% (from simulation) or 46% (from test)
increase in bearing capacity. The optimum buried depth is 0.4B from sandbox test, 0.5B
from numerical simulation. The optimum reinforcement length is 4B from sandbox test,
5B from numerical simulation. These two values are within the range reported by the
investigators in the reviewed literatures. Therefore, for design purpose, it is recommended
to use 0.4B for buried depth and 5B for reinforcement length.
Acknowledgments
The authors wish to thank Mr. Henry Sie of ACE Geosynthetics for providing the geotextile
used in this study. His support is deeply appreciated.
Page12
References
[1] Binquet, J. and Lee, K. L., “Bearing Capacity Tests on Reinforced Earth Slabs,” J.
Geotech. Engrg. Div., Vol. 101, 1975, pp. 1241-1255.
[2] Chang, J. C., Hannon, J. B., and Forsyth, R. A., “Pull Resistance and Interaction of
Earthwork Reinforcement and Soil,” Transportation Research Record 640,
Transportation Research Board, 1977, pp. 1-7.
[3] Vidal, M. H., “The Development and Failure of Reinforced Earth,” Keynote Address of
Symposium on Earth Reinforcement, ASCE Annual Convention, 1978, pp. 1-61.
[4] Juran, I., Knochenmus G., Acar Y. B. and Arman A., “Pull-Out Response of Geotextiles
and Geogrids,” Geosynthetics for Soil Improvement (GSP 18), ASCE, Reston/VA, 1988,
pp. 92-111.
[5] Binquet, J. and Lee, K. L., “Bearing Capacity Analysis of Reinforced Earth Slabs,” J.
Geotech. Engrg. Div., Vol. 101, 1975, pp. 1257-1276.
[6] Schlosser, F. and Elias, V., "Friction in Reinforced Earth," Proceedings of the ASCE
Symposium on Earth Reinforcement, ASCE, Pittsburgh, Pennsylvania, USA, 1978, pp.
735-763.
[7] Huang, C.C. and Tatsuoka, F., "Bearing Capacity of Reinforced Horizontal Sandy
Ground," Geotext. and Geomembr., Vol. 9, No. 1, 1990, pp. 236-267.
[8] Huang,C.C. and Menq, F.Y., “Deep-Footing and Wide-Slab Effects in Reinforced Sandy
Ground,” J. Geotech. and Geoenvin. Engrg., Vol. 123,, No. 1, 1997, pp. 30-36.
[9] Yamamoto, k. and Kusuda. K., “Failure mechanisms and bearing capacities of reinforced
foundations,” Geotext. and Geomembr., Vol. 19, No. 1, 2001, pp. 127-162.
[10] Yetimoglu, T., Wu, T.H. and Saglamer, A., “Bearing Capacity of Rectangular Footings on
Geogrid-Reinforced Sand,” J. Geotech. Engrg., Vol. 120, No.12, 1994, pp. 2083-2099.
[11] Kotake, N., Tatsuoka, F., Tanaka, T., Siddiquee, M.S.A., and Huang, C. C., “FEM
Page13
Simulation of the Bearing Capacity of Level Reinforced Sand Ground Subjected to
Footing Load,” Geosynth. Int., Vol. 8, No. 6, 2001, pp. 501-549.
[12] Yamamoto, A. and Otani, J., “Bearing capacity and failure mechanism of reinforced
foundations based on rigid-plastic finite element formulation,” Geotext. and Geomembr.,
Vol. 20, No. 1, 2002, pp. 367-393.
[13] Chakraborty, D. and Kumar, J., “Bearing Capacity of Strip Foundations in Reinforced
Soils,” Int. J. Geomech., Vol. 14, No. 1, 2014, pp. 15-58.
[14] Deb, K., Sivakugan, N., Chandra, S., and Basudhar, P. K., “Numerical Analysis of
Multilayer Geosynthetic-Reinforced Granular Bed Over Soft Fill,” Geotech. Geol. Eng.,
Vol. 25, No. 6, 2007, pp. 639-646.
[15] Yang, B., Lai, J., Lin, J., and Tsai, P., “Simulating the Loading Behavior of Reinforced
Strip Footings with a Double-Yield Soil Model.” Int. J. Geomech., Vol. 16, No. 1, 2016,
B6015001.
[16] Fragaszy, R. and Lawton, E., “Bearing Capacity of Reinforced Subgrades”, J. Geotech.
Engrg., Vol. 110, No. 10, 1984, pp. 1500-1507.
[17] Verma, B. P., and Char, A. N. R., “Bearing Capacity Tests on Reinforced Sand
Subgrades,” J. Geotech. Engrg., Vol. 112, No. 7, 1986, pp. 701-706.
[18] Khing, K. H., Das, B. M., Puri, V. K., Cook, E. E., and Yen, S.C., “The Bearing Capacity
of a Strip Foundation on Geogrid-Reinforced Sand,” Geotext. and Geomembr., Vol. 12,
1993, pp. 351-361.
[19] Omar, M. T., Das, B. M., Puri, V. K., and Yen, S. C., “Ultimate Bearing Capacity of
Shallow Foundations on Sand with Geogrid Reinforcement,” Can. Geotech. J., Vol. 30,
1993, pp. 545-549.
[20] Dash, S. K., Krishnaswamy, N. R., and Rajagopal, K., “Bearing Capacity of Strip
Footings Supported on Geocell-Reinforced Sand,” Geotext. and Geomembr., Vol. 19, No.
Page14
4, 2001, pp. 235-256.
[21] Ghosh, A. and Bera, A. K., “Bearing Capacity of Square Footing on Pond Ash Reinforced
with Jute-Geotextile,” Geotext. and Geomembr., Vol. 23, No. 2, 2001, pp. 144-173.
[22] Abu-Farsakh, M., Chen Q., Sharma R., and Zhang X., “Large-Scale Model Footing Tests
on Geogrid Reinforced Marginal Embankment Soil,” ASTM Geotechnical Testing
Journal, Vol. 31, No. 5, 2008, pp. 413-423.
[23] Abu-Farsakh, M., Chen Q., and Sharma R., “An Experimental Evaluation of the Behavior
of Footings on Geosynthetic-Reinforced Sand,” Soils and Foundations, Vol. 53, Issue 2,
2013, pp. 335–348.
[24] Chen Q. and Abu-Farsakh M, “Ultimate Bearing Capacity Analysis of Strip Footings on
Reinforced Soil Foundation,” Soils and Foundations, Volume 55, Issue 1, 2015, pp.
74-85.
[25] Sharma R., Chen Q., Abu-Farsakh M., and Yoon S., “Analytical Modeling of Geogrid
Reinforced Soil Foundation,” Geotextile and Geomembrane, Vol. 27, No.1, 2009, pp.
63-72.
[26] Itasca, “FLAC-Fast Lagrangian Analysis of Continua: Constitutive Models,” User’s
Manual of FLAC V5.0, Itasca Consulting Group, Minneapolis, MN, 2002, pp. 2-58 - 2-71.
[27] Peng, F. L., Kotake, N., Tatsukoka, F., Hirakawa, D. and Tanaka, D., “Plane Strain
Behavior of Geogrid-reinforced Sand and its Numerical Analysis,” Soils and Foundations,
Vol. 40, No. 3, 2000, pp. 55-74.
[28] Jewell, R. A. and Worth, C. P., “Direct Shear Test on Reinforced Sands,” Geotechnique,
Vol. 37, No. 1, 1987, pp. 53-68.
Page15
TABLE 1. Properties of sand used in this study.
Properties Value
Specific gravity 2.70
Grain size (mm) D10 0.17
D30 0.28
D60 0.50
Dry density (kg/m3) Maximum 1743
Minimum 1375
Tested 1412
Relative density (%) 12.4
Cohesion (kPa) 0
Angle of friction (degrees) 34.4
TABLE 2. Properties of geotextile used in this study.
Properties Value
Tensile strength (kN/m) MD* CD*
2% elongation 9.6 14.3
5% elongation 27.0 32.3
10% elongation 56.8 63.8
Mass density (g/m2) 338
Thickness (mm) 0.86
* - MD: Machine Direction; CD: Cross Direction
TABLE 3. Properties of sand used in numerical simulation
Density (kg/m3)
Dilation Angle min. (
o) Friction Angle
peak (o)
Shear Modulus(Pa)
Bulk Modulus (Pa)
Stiffness Ratio(R )
1412 -3 34.4 3.84x105 1.15x106 5.5
TABLE 4. Properties of geotextile used in numerical simulation
Basic Property Axial Property Interface Property
Thickness
(mm)
Mass Density (g/m2)
Ultimate Strength (kN/m)
Elastic Modulus
(kPa)
Stiffness kbond
(kN/m/m)
Cohesive Sbond
(kN/m)
Friction Angleinterface
(o)
0.86 338 63.5 8.31x105 750 25 11.5
Page16
TABLE 5. Effectiveness of two reinforcement layers
BCRd
s/B d/B = -0.2 d/B = 0 (single layer) d/B = 0.2
Test Numerical Test Numerical Test Numerical
5% 1.01 1.12 1.20 1.09 1.01 1.13
10% 1.15 1.20 1.26 1.12 1.15 1.18
15% 1.34 1.29 1.35 1.18 1.29 1.27
20% 1.55 1.39 1.46 1.23 1.43 1.36
Page17
Figures Caption
Fig. 1. Schematic drawing of the experimental setup
Fig. 2. Mohr-Coulomb failure criterion in FLAC [26]
Fig. 3. Cap stress vs. volumetric strain of Double-Yield Model [26]
Fig. 4. Schematic drawing of finite difference mesh used in numerical simulation
Fig. 5. Stress- volumetric strain curve of the loose sand from Oedometer test
Fig. 6. Shear stress-shear displacement curves of the loose sand from direct shear tests
Fig. 7. Shear stress ratio and dilation angle of the loose sand from direct shear test
Fig. 8. Shear yield function of the loose sand obtained from direct shear test
Fig. 9. Comparison between simulated and tested load-settlement curves of strip footing on
unreinforced sand
Fig. 10. Comparison between simulated and tested load-settlement curves of strip footing on
unreinforced sand
Fig. 11. Effects of depth and length of single reinforcement on the bearing capacity from
numerical simulation
Fig. 12. Comparison between simulated and tested BCR at various buried depths
Fig. 13. Comparison between simulated and tested BCR at various reinforcement lengths
Fig. 1. Schematic drawing of the experimental setup
Fig. 2. Mohr-Coulomb failure criterion in FLAC [26]
Fig. 3. Cap stress vs. volumetric strain of Double-Yield Model [26]
Fig. 4. Schematic drawing of finite difference mesh used in numerical simulation
Fig. 5. Stress- volumetric strain curve of the loose sand from Oedometer test
Fig. 6. Shear stress-shear displacement curves of the loose sand from direct shear tests
Fig. 7. Shear stress ratio and dilation angle of the loose sand from direct shear test
Fig. 8. Shear yield function of the loose sand obtained from direct shear test
Fig. 9. Comparison between simulated and tested load-settlement curves of strip footing on
unreinforced sand
Fig. 10. Comparison between simulated and tested load-settlement curves of strip footing on
unreinforced sand
Fig. 11. Effects of depth and length of single reinforcement on the bearing capacity from
numerical simulation
Fig. 12. Comparison between simulated and tested BCR at various buried depths
Fig. 13. Comparison between simulated and tested BCR at various reinforcement lengths