Download - Measurement of CMS Luminosity
1
MEASUREMENT OF CMS LUMINOSITYN. Adam, R. Hall-Wilton, V. Halyo, A. Heister, J. Hollar, A. Hunt, D. Marlow, A. Pozdynyakov, M. Schmitt, D. Stickland, M. Valesco, J. Werner, & Z. Xie, M. Zanetti
12/8/10
2
Overview Methods for luminosity measurement at
CMS: Online - HF Offline - HF & Vertex
Performance and comparison of methods Absolute calibration using Van Der Meer
Scans: Introduction to the method Scans & Results at CMS Systematic Uncertainties
Results & Conclusion
3
CMS Luminosity is continuously measured (“KEEP_ALIVE”) using the forward hadronic calorimeters (HF) in two ways:1. Tower occupancy
measurement (2 × 2 h rings: 33-34L, 35-36L)
2. Total ET measurement (4 h rings: 33-34L + 35-36L)Single HF Tower (13)
with alternating long (L) and short (S) fibers.
Luminosity Measurement:Online - HF
Start from formula relating luminosity to number of interactions, where μ = mean number of interactions per BX, σ = pp cross-section, L = instantaneous luminosity and f = BX frequency.
For a noiseless calorimeter system, with p being the probability that a tower is not hit in a single interaction, it is easy to show that the average fraction of empty towers f0 goes as:
Accounting for noise is a non-trivial exercise that adds non-linear corrections. These are small (ε<<1) under certain conditions that our system meets. The final expression for the log of the empty tower fraction is linear with μ.
4
€
μ =σLf
€
f0 = e−(1− p )μ
€
−ln f0 = (1 − p)(1 −ε)μ +N
Slope correctionNon-linear, but smallNoise offset
No. of interactions is Poisson with mean μ
For more details see: CMS IN-2007/030
Luminosity Measurement:Online – Tower Occupancy
It is similarly possible to show that the average transverse energy sum per BX will also be linear with the number of interactions:
In this case there is no inherent non-linearity in the method. However, if truncation is used (as occurs in the Look-up Table (LUT)), extra non-linear terms are introduced.
The effect of this truncation is small (<2%) even over a very large range of luminosities, 1028 – 1034 cm-2s-1.
5
€
ET =ν s(1− p)μ +N
ns gives the average energy of a single interaction bunch crossing.
Noise offset.
For more details see: CMS IN-2007/030
Luminosity Measurement:Online – ET Sum
6
HF Offline (Zero Counting Method) Require SET > 1GeV in both HF+ and HF- Require |t| < 8ns in both HF+ and HF-
Vertex Counting Offline Require ≥ 1 vertex with |z| < 15cm
Monte Carlo Efficiency Estimate
Luminosity Measurement:Offline – HF & Vertex
σMinbias = 73.1 mb
Method Efficiency Eff. Cross-Section
HF 63.4 % 45.2 mbVertex 73.4 % 52.3 mb
7
Absolute Calibration Method
€
L =N1N2 fNbAeff
Luminosity can be accurately measured by scanning the beams across each other (separation scan method) and measuring the size and shape of the interaction region. [Method pioneered by S. Van Der Meer at ISR.] Note: method is in principal independent of the beam profile shape.
8
Absolute Calibration at CMS
The separation scan method is used for absolute calibration at CMS. Have 25 points per scan, out to ~4.5σ.
A double-Gaussian beam profile is needed to fit the beams observed in CMS. Significant luminosity in the tails of the distribution.
Luminosity at beam separation d is given by
€
L =N1N2 fNbF(0,0)
fx (Δx)dΔx fy (Δy)dΔy∫∫L =
N1N2 fNb2πσ eff (x)σ eff (y)
σ eff (i) =σ 1iσ 2i
hiσ 2i + (1 − hi)σ 1i
€
N1 = intensity Beam 1N2 = intensity Beam 2f = frequencyNb = no. BX's per beamF(x,y) = fx (x) fy (y)
fx (x) =hx
2πσ 1x
exp−x 2
2σ 1x2 +
(1 − hx )2πσ 2x
exp−x 2
2σ 2x2
hx = core fraction
€
L(d) = L0hi
2πσ 1i
exp−d2
2σ 1i2 +
(1 − hi)2πσ 2i
exp−d2
2σ 2i2
⎛
⎝ ⎜
⎞
⎠ ⎟
9
Scans at CMS Calibration scans were performed at
CMS in fills 1386 and 1422. Preferred VdM scan with 4.5σ tails in fill 1386 only.
Fill 1386: 6 colliding bunches. Single scan in each plane (X & Y). Fill 1422: 3 colliding bunches. Two scans in each plane XX then YY. Scan optimized for alternate calibration
method.
10
Online Scan Results: Fill 1386
All colliding bunches combined.
11
Online Scan Results: Fill 1386
All colliding bunches combined.
12
Online Scan Results: Fill 1386
Example individual BX = 1451
13
Online Scan Results: Fill 1422
All colliding bunches combined.
14
Online Scan Results: Fill 1422
All colliding bunches combined: X scans.
15
Online Scan Results: Fill 1422
All colliding bunches combined: Y scans.
16
Calibration & Absolute Luminosity Results
To calibrate we use the central peak luminosity or “zero” points with all combination of measured beam widths. The measured beam widths are corrected for emittance blow-up. Final points on each plots are the average normalization. Ratio = normalization result relative to current CMS normalization.
17
New Length Scale Calibration (F1439)
18
Difference from Nominal Separation
19
Preliminary Results using 1st scan…
Design and performance of the luminosity system have been presented.
Analysis of the Van Der Meer scan data has been used to arrive at preliminary !!!! new absolute normalizations for the luminosity measurement from fill 1386 relative to current CMS normalization:
Rscan/cms = 1.001 ± 0.001
20
Lumi using the HF during HI run
We will validate the HFlumi online DB results using the BSC and also offline vertex counting, as we do for the pp lumi.
21
Summary Scan analysis is in progress and results
will be reported on Jan 13 LHC workshop Results for HI are in being validated Standard DAQ servers will be soon
purchased and commissioned for next year run.