Creating better results together 2
Our Health Safety & Wellbeing Management System has been developed to
ensure highest standards of Safety, Health and Wellbeing on site.
This is one of a series of Visual Standards created to help everyone understand
what ‘’good looks like’’ contributing to setting a positive safety, health and
wellbeing culture across the programme.
The easy to follow pictures will allow project teams to quickly determine whether
their site provisions meet our SH&W expectations.
Creating better results together 2
How This manual will be available both in version controlled electronic and hard copy. The hard copy will be printed in weather proof format for use on site.
Who All personnel listed below should have access to, read and understand this manual. • Construction Manager/Project Manager • Site Supervisors • Site Forman • Contractors • SHW Advisors • Network Site Teams
When The existence and usage of this Visual Standard should be discussed as part of the Safety, Health and Wellbeing introduction at pre-start meetings. This manual will be reviewed and updated when new safety, health and wellbeing risks are identified as a result of new activities on site.
Contents
Creating better results together 4
1. Competency & Induction requirements
2. Plant Operators competency
3. Means of communication
4. Permits
5. Customer excellence
6. PPE
7. RPE
8. Signing, Lighting & Guarding
9. Parking on site
10. Towing of Plant
11. Unhitching trailer from towing vehicle
12. Coil Trailers
13. Van Housekeeping
14. Essential Safety Equipment
15. Utility Avoidance
16. Vibration Management
17. Noise Management
18. Manual Handling
19. Lifting operations
20. Lifting ancillaries
21. Working at height
22. Delivery of materials
23. Personal hygiene
24. Cross contamination & Public Health
25. Leptospirosis (Weil’s disease)
26. Asbestos
27. Hand held Plant Operations
28. Tools & Equipment
29. Cut off Saw use
30. Vacuum Excavator/Air Lance
31. Excavation Safety
32. Excavation Support
33. Temporary Works
34. Moling operations
35. Drilling walls/panels
36. Service laying minimum standards
37. Tools for Cutting Pipework
38. COSHH
39. Environmental
40. Use of mobile phones
41. Housekeeping on site
42. Working with tipper raised
43. Road roller & other towed plant
44. Rammer
Quality & Pride in Workmanship
45. Edge Preparation
46. Edge proximity to other apparatus
47/48/49/50. Compaction
51. Over – banding
52. Pavement Slabs
53/54. Don’t leave hazards behind
55. Completion of reinstatement work
56. Dealing with unhappy customer
eight2O Visual Standards
1. Competency and induction requirements
Creating better results together 5
• Every person will receive eight2o health, safety and wellbeing induction.
• Everyone must hold and maintain the relevant core qualification/competency:
eight2O orientation/induction
Front Line Supervisors will receive a separate role assessment & induction
Thames Water’s Safety Passport
Plant Operators – CPCS/NPORs
NRSWA Operatives/Supervisors (1 NRSWA Operative per team, 1 NRSWA Supervisor appointed to oversee
the work)
National Water Hygiene (EUSR)/DOMS (As specified in Our Safety, Health & Wellbeing Approach)
Thames Water Pink Card
• ID cards and competency cards must be carried at all times.
• Never carry out work or operate plant and equipment that you are not authorised, certified or qualified to do.
eight2O Visual Standards
2.Plant Operator Competency
Creating better results together 6
Never operate any plant/machinery unless you have been properly trained, authorised/ have provided Fit for
Work Medical certificate and hold the appropriate class of driving licence or training certificate e.g.
• Mechanical excavator
• Dumper truck
• Fork lift truck
• Grab/hiab lorry
• Mechanical winch
• Trencher/top cutter
• Road saw
• Horizontal directional drilling (HDD)
• Mobile elevated work platforms (MEWP)
• Lifting with Excavators/Excavators used as cranes (operator to hold an equipment competency card)
• Other training required to operate specialist equipment
• Traffic Marshal/Banksman
Operators of any plant must carry out daily visual checks and maintain training log books of their vehicles using the
appropriate inspection sheet and record and report any defects immediately. To prevent unauthorised use, all plant
must be immobilised when not in use, remove the keys.
eight2O Visual Standards
3. Means of communication
Creating better results together 7
• Readiness Review completed and communicated before the start of project.
• CPP advised suitable
• F10 within date and displayed on site
• Site inductions carried out
• Utility plans available and in good condition
• Daily plant checks completed and available for inspection
• Project risk assessments and method statement completed
• Safe Start Pre-Task briefing completed
• Site specific permits complete
eight2O Visual Standards
4. Permits
Creating better results together 8
A permit to work system is a formal written system used to control certain types of work that are potentially
hazardous.
• At the planning stage check if permit to work is required from the Local Authority/ Environmental Agency etc.
• Thames Water Permits to Work are required for the following operations:
Confined Spaces
Low and High voltage electricity
Hot Work
General or Mechanical Permits
Sludge Digester
Permit to break surface (any break of surface)
Deep Excavation Permit
Works on contaminated land
Lifting operations
Use of HDD (horizontal drilling), mains bursting
moling, top cutters/ trenchers etc.
Works on or near a demolition site
Works on plant containing toxic material
Permit to load/remove supports
Licence to operate – working on clean water main
eight2O Visual Standards
5.Customer excellence
Creating better results together 9
Everyone in the alliance can impact upon customer experience, so has a responsibility to deliver this to an exceptional
standard. You might be the only contact a customer has with Thames Water, so make it memorable!
How to start a conversation
• Introduce yourself with a smile, a handshake and ID
• Provide safety information including where excavations
will be
• Offer immediate assistance or information
• Explain why you are there and what will happen next
• Agree driveway and other access requirements
Noisy equipment
• Follow official council/contract guidelines for time
to use this on-site
• Set a realistic expectation of start and end times/dates,
and noise levels
Behaviour during works
• Have a complete, clean and correctly branded PPE kit
• Do not swear or use inappropriate language on site
• If you need to turn your customer’s water off, give them
adequate notice, explain why this is necessary and set
time expectations
• Manage customer expectations for work completion dates,
especially when they change
• Provide customers with a site contact if requested
• Treat your customers as you would like to be treated
• In your vehicle: do not swear, smoke or use your mobile
phone, and consider where you park and how this will
affect others
• Customer satisfaction survey cards must be left at all
affected properties post-works
Ideal site conditions
• Leave/provide an alternative, safe and adequate walkway
for the public
• Have a clean, safe and tidy site with no rubbish
• Provide clear, good-quality and branded signage, for
drivers and pedestrians
• Securely link barriers up, sectioning off equipment and
excavations from the public
• Have all equipment neatly placed or put away
• Backfill all trenches and holes when works are complete
• Private reinstatement holes must be filled in as soon as
dug and must be reinstated within 5 working days of
service test completion
eight2O Visual Standards
5. Customer excellence
Creating better results together 10
Be customer positive::
P romise Keep the promises I make.
O wnership My customer, my responsibility
S mile Make a lasting first impression.
I nnovation Reduce the need for customers to contact us
T hink Put yourself in the customer’s shoes
I nformed Proactively communicate with customers
V oice Involve customers in feedback opportunities
E asy Make it simple; resolve contact quickly
eight2O Visual Standards
6. Mandatory personal protective equipment (PPE) on site
Creating better results together 11
• Please refer to Our Safety, Health & Wellbeing Approach for PPE
specification.
• Mandatory personal protective equipment (PPE) on site –
Management, Supervisors and Teams
Hard hat BSEN397
Blue – Front Line Supervisor (FLS)
Red – Fire Marshall/Vehicle Marshall
Green – First Aider (or sticker, if required to wear other colour of hat)
Orange – Slinger/Signaller
White – General Operative
Black – Visitor
Yellow – Managers/Engineers
• Appropriate safety glasses to EN166
• High visibility jacket – long sleeves to EN471 (flame retardant & arc
resistant - orange)
• Overalls (flame retardant and arc resistant - orange) for all breaking
ground activities.
• Steel toe capped boots to EN345
• Appropriate gloves to EN 388-4131
• RPE as identified in Risk Assessment.
• Ear defenders as identified in Risk Assessment.
eight2O Visual Standards
7. RPE
Creating better results together 12
• Face Fit Test to be carried out before commencing any work activity
• Face Fit Test must be repeated if the user has had a change to the shape of his face or where there is a change to the
model of BA face mask issued or factual hair growth.
• Those wearing Breathing Apparatus must be clean shaven.
• Ensure mask is in good conditions and filters are changed where required.
eight2O Visual Standards
8. Signing, lighting and guarding
Creating better results together 13
• Consult Thames Water Essential Standard No 16 – Short duration
street works and NRWSA
• Consult Thames Water Essential Standard No 15 -Protecting the
public during temporary work activities
Ensure the safety of the public and your team
• Consider vulnerable member of the public as they are especially at
risk.
• Ensure all advance warning signs are in place (W.I.D.E).
• Take into account weather conditions (rain, fog, night)
• 100% guarding of excavations at all times and kerb ramps must be in
place.
• Safety zone with cones & pedestrian walkways in place.
• Feet in place on every barrier.
• Signage displayed and secured to prevent trips.
• Courtesy and permit signs displayed.
• Spoil barriered off.
• Minimum of 1 lamp on every excavation.
• Daily Inspection of works.
• Minimum walkway width required (1m).
• Statutory Undertakers Board.
Will a member of the public know what is
expected of them as they approach of the
works?
eight2O Visual Standards
9. Parking on site
Creating better results together 14
• Do not block driveways, disabled parking or any other restricted parking area
• Reverse parking and always use a Vehicle Marshall when manoeuvring vehicle/plant.
• Do not park illegally, if parking in a Pay & Display – Buy a ticket
• Allow enough space to access the rear of the vehicle
• The side door is to be accessed from the pavement
• Working zone for tools, equipment and materials to be created using barriers and cones
Is this your van?
!!!!!!!!!!!!!
eight2O Visual Standards
10. Towing of plant
Creating better results together 15
• You must never tow more than your licence permits you to do.
• Always check that you have the correct driving licence competency to tow any plant.
• Drivers who passed a car test on or after 1st January 1997 are required to pass an additional test in order to gain
entitlement to category B+E. Category B includes vehicles up to 3.5 tonne, which is coupled with a trailer up to 750kgs,
combined weight 4.25 tonne.
• Check to ensure the trailer is roadworthy and within the correct weight limit for your vehicle.
• Always ensure the load/plant is secure and properly strapped down before setting off.
• You must ensure the trailer is properly attached to the towing vehicle, ensure the snatch cable is connected and the lights
are working.
• Trailers must also show the same registration number as the towing vehicle and registration.
• Number plates must not be obscured.
• Only load and unload trailer when on level surface.
• Always use a traffic marshal when reversing.
• Inspection of trailer.
• No other material to be transported on a trailer then designated.
• When trailer unhitched ensure it is prevented from moving.
eight2O Visual Standards
11. Unhitching trailers from towing vehicles
Creating better results together 16
• When directing any vehicle always stand where the driver can see you at all times and out of the way of the trailer. Never
stand between a reversing vehicle and the trailer.
• When parking a trailer, always assess the best position for the trailer (e.g. angled into the can kerb act as additional
protection).
• When hitching up, do not release the trailer handbrake or remove the wheel chocks until the trailer is connected to the
towing vehicle.
• Before moving always check the load to ensure it is secure.
• Check to ensure the trailer lights are functioning correctly and the overrun cable is connected and free to move.
ALL OPERATIONS SHOULD REQUIRE HAND PRESSURE ONLY. DO NOT USE EXCESSIVE FORCE, YOUR FOOT OR
ANY IMPLEMENT TO STRIKE THE LOCK LEVER HANDLE.
Always consider safety of your colleagues and members of the public.
Remember it is the drivers responsibility to ensure trailers are connected and disconnected safely and all loads are
secured.
Keep wheel chocks in place
until the trailer is
connected to the towing
vehicle.
eight2O Visual Standards
12. Coil Trailers
Creating better results together 17
• Coil must be securely restrained for transportation.
• Pipe end clamps secured to the opposite centre hub shall be used when dispensing the pipe.
• Coil trailers shall be secured on site with hand brake on and support legs utilised.
• Care should be taken when rotating the coil within the trailer and to secure the pipe when cutting.
• Part used coils shall be secured before transporting back to depots.
• 180mm pipes may be higher than some bridges - plan your route.
• Traffic marshal when reversing.
• Load and unload on a level ground.
When trailer unhitched ensure it
is prevented from moving
eight2O Visual Standards
13. Van Housekeeping
Creating better results together 18
• Vehicle cab to be clean and tidy.
• Dashboard to be clear of paperwork.
• First aid kit and eye wash kit to be available.
• Hand washing facilities to be available
• Tools and equipment to be secured and stored safely.
• Heavy equipment to be secured and stored near door to aid manual handling.
• Chemical substances to be stored according to COSHH assessment.
• When possible use a marshal when reversing a vehicle.
• Access and egress maintained in back of van.
• Spill kit to be easily accessible.
* All vehicles to be marked with Thames Water logo and comply with Thames Water Driving Standards.
Poor housekeeping leads to incidents Good housekeeping keeps you safe and
makes your work easier
eight2O Visual Standards
14. Essential Safety Equipment
Creating better results together 19
• Before breaking of surface obtain permit and use CAT & Generator with data logging capacity.
• Only use equipment that has been approved for issue by the company and ensure you are trained and authorised to use
it.
• Before you use any of these items you must check for and report any defects or damage.
• If it not safe to use do not start work until a replacement tool has been obtained.
• Check that the equipment has a current inspection/calibration validity date (ex. PA Test in date)
• Report any equipment when damaged or not working correctly.
eight2O Visual Standards
15. Utility avoidance
Creating better results together 20
• Operators trained and provided with data logging CAT &
Generator
• Air Lance provided to every Network Team
• Obtain and understand up-to-date plant and drawings. Ensure they
are available on site at all times.
• Check data logging CAT & Generator in good working order and
within calibration date and undertake a function check prior to
sweeping the area to be excavated.
• Prior to excavation within the vicinity of any critical 3rd party assets
and clients (oil/ gas/ petroleum/ fuel pipes) obtain specific
information. Arrange for an on site meeting with the pipeline owner
and agreed method of work (written & approved).
• Check for other visible signs of existing underground apparatus
such as street furniture, overhead lines and surface scarring.
• Minimum distance to be maintained when using mechanical plant:
– 500mm
• Hand dig to establish line and route of all plant
• Ensure that your mark up is visible outside of the planned
excavation area at all times for the duration of the work.
• Do not use power tools directly over a marked buried conductor.
• Use the air lance where possible.
• Ensure compliance with HSG47
• Mark up all plant routes next to the excavation area inside and
outside of the planned excavation.
• Ensure you use plant detection equipment as the excavation
progresses. Minimum every 300mm.
• Mark plant exclusion zones.
eight2O Visual Standards
17. Vibration management
Creating better results together 22
• Eliminate/reduce exposure to HAV as much as possible by selecting suitable work method/plant.
• Risk Assessment/ Method Statement in place/signed and understood?
• Have you chosen the lowest vibration tool that is suitable and can do the job efficiently?
• Limit the time that each worker uses high vibration tools (concrete breakers, angle grinders or hammer drills).
• Know the vibration levels produced by the equipment you use
• Provide information and training to operatives so they know what the risks are from (HAV) and what they need to do to
avoid those risks.
• Vibrating tools to be properly maintained this includes keeping bits and drills sharp.
• Vibrating tools to be inspected daily with a weekly report produced.
• Arranged health surveillance for people exposed to high levels of HAV, especially when exposed for long periods.
• HAV meter to be used by all operatives using vibrating tools.
HAVS is preventable, but once the damage is done it is Permanent
Prevention is the only cure for HAVS
Vibration not monitored !
eight2O Visual Standards
18. Noise Management
Creating better results together 23
• Eliminate/ reduce exposure to noise. Can you use quieter equipment or a quieter process?
• Read & understand Risk Assessment prior to work and know what control measures you need to put in place.
• Do you know the risks from noise? Do you know noise levels produced by the equipment you use?
• Refer to eight2O Noise CRIBB Card
• Maintain plant and equipment .
• Ensure you wear hearing protection as identified by in Risk Assessment and Method Statement. Type of hearing
protection will depend on noise exposure levels generated. Have you been trained on the use of PPE?
• Be considerate of contractors and members of the public working in close proximity. Where appropriate advise them to
wear hearing protection. Alternatively consider acoustic insulation in the area.
• Provide Health Surveillance
Don’t lose your hearing!
eight2O Visual Standards
19. Manual Handling
Creating better results together 24
Manual handling when lifting of manhole covers and valve operation:
• Manhole covers come in all shapes, sizes and weights.
• Valves may be stiff
• Carry out Risk Assessment of the operation to be undertaken
• Ensure the weather conditions, lighting and location of the valve adequate to carry out the activity safely.
• Can you carry out the procedure without putting yourself or members of the public at risk?
• Use mechanical manhole lifting equipment in preference to manhole keys if appropriate
• Use undamaged valve keys of the correct size
• use of lubricants to free the valve and whether consider asking for assistance
• Warm up before attempting the task
Use of manhole key not
allowing good lifting
posture!
Better lifting
posture & greater
distance between
the person lifting
& the cover
eight2O Visual Standards
20. Lifting operations
Creating better results together 25
Key points • Crane Authorisation obtained from Thames Water?
• Is Lifting Plan in place – this includes lifting using Excavators & HIAB?
• When excavator is used as lifting equipment ensure that only appropriately trained operators carry out the lift
• Follow the lifting minimum standards for basic lifts
• Check the ground conditions – will it support the plant being used?
• Make sure the works are properly guarded
• Close the footpath when lifting over the footpath
• Provide clear signs for pedestrians
• Beware of overhead cables
• Always use a Reversing Vehicle Marshall when manoeuvring plant/vehicle in a restricted area.
• Always use a Slinger/Signaller for grab bucket movements.
• Hard hats must be worn (Orange for Slinger Signaller)
• If necessary hand barrow material (rather than lift over pedestrians or parking your vehicle unsafely).
• NO OBJECT HANDLING CAPACITY NO LIFTING
Hitch tilted backwards with master link
subject to twisting/ bending !
Chain and master link can hang freely without obstruction
eight2O Visual Standards
21. Lifting ancillaries
Creating better results together 26
Key points • Refer to the Lifting Operations Procedure for Guidance on Basic Lifts.
• Straps, chains and shackles must be thoroughly examined every 6 months.
• Make sure you have the certificates for your lifting equipment with your vehicle.
• Return damaged lifting equipment to stores and mark the equipment as damaged.
• Check the SWL and ensure this is sufficient for the load.
• Only use approved plates which are clearly marked with their weight.
• Ensure the load is lifted at a correct angle.
• Inspection of lifting equipment report to be provided weekly
Inspected lifting accessories,
stored in a suitable place
Incorrectly stored
lifting equipment,
prone to damage!
eight2O Visual Standards
22. Working at height
Creating better results together 27
Always avoid working at height if possible. Can it be done from the ground?
• If you have to work at height carry out a Risk Assessment & Method Statement, make sure you know the control
measures.
• Refer to the working at height minimum standards guidance.
• Assess what the safest way to complete the work is – scaffold/alloy tower/podium/ladder.
• Consider the factors of Level ground/access/accessibility/duration of work/how much work is needed.
• Only use ladders/step ladders for short duration, low risk work.
• Site your ladder at an angle of 1 in 4 or 75°.
• Keep 3 points of contact at all times and never work on the top 5 rungs of a ladder.
• Secure the ladder to prevent slipping.
• Inspection and tags in place.
• Consult Thames Water Essential Standard No. 2 Working on Roofs if such work is required.
Poor material
movement and
handling disciplines
producing serious
falls from height
issues!
eight2O Visual Standards
23. Delivery of Materials
Creating better results together 28
Poor material movement and handling disciplines
producing serious falls from height issues in both
cases!
Fall prevention in place
for loading/unloading of
flat bed trucks. Where fall
prevention is not available
fall arrest systems is
used.
Key Points • Plan for safe unloading or loading of
materials.
• Select appropriate handling equipment
to avoid access onto vehicles.
• Provide equipment to prevent falls.
• Provide equipment to minimize the harm
from a fall.
• FORS minimum of bronze for logistics
vehicles
eight2O Visual Standards
24. Personal Hygiene
Creating better results together 29
Key points
• EUSR Card obtained? • Exposure to sewage can lead to: cramping stomach
pain/ diarrhoea/vomiting/Weil’s disease/Hepatitis/asthma/skin & eyes infection etc.
• How does this happen? Hand to mouth contact (eating/drinking/smoking or
when wiping your face with contaminated hands/gloves).
Skin contact (Cuts/scratches/surface of skin) Breathing ( dust/aerosol/mist) • Wash your hands with antibacterial soap before
eating/drinking/smoking /touching your face • Wash your hands after using the toilet • Check food that you eat is correctly stored, prepared
and properly cooked. • Remove and correctly dispose of consumable PPE • Arrange for cleaning of dirty workwear & PPE • Remove dirty workwear & PPE in the drying and
wash your hands before heading to eat your meal/ entering offices and other welfare facilities
• Challenge persons who are not maintaining
acceptable levels of good personal hygiene.
eight2O Visual Standards
25. Cross contamination & Public Health
Creating better results together 30
You must not work on potable water if you do not hold EUSR card or if any of your household suffer from stomach pain/prolonged
fever/food poisoning/ infective hepatitis and jaundice.
• EUSR Card obtained?
It is essential to follow simple steps and
procedures to safeguard the quality of water
reaching our customers.
When pipe fittings are stored on site they should
be adequately protected from contamination.
All tools & equipment used near fittings when
being installed must be kept clean & disinfected.
Pipes should remain capped or wrapped as long
as possible. They also should be kept on pallets
to keep them clear of the ground and any
flooding.
It is extremely important we cap all open ended
pipe work to prevent contamination.
Where competing priorities exist between
minimising the risk of contamination and restoring
the supply as soon as possible or completing a job
by a target date, the over-riding consideration must
be to ensure that public health is not
compromised.
eight2O Visual Standards
26. Leptospirosis (Weil’s disease)
Creating better results together 31
Report ALL incidents and near misses and hazards promptly
Key points
• Route of Entry - through contaminated fluids, tissues, or waters. The
infection enters through any breaks in the skin (e.g. abrasions, cuts).
• Cause - through contact with animal urine (exposure to infected animal
tissue, land, water, any surface or product that could have been exposed
to direct contact.
In order to limit the risk of contracting the disease the following must be
adhered to at all times:
1. Wash your hand regularly and dry on disposable towels not down cloths
as cloths maybe contaminated and use alcohol wipe which are provided.
2. Do not handle rats, dead or alive, without adequate PPE.
3. Avoid all hand to mouth contact.
4. Eat, drink and smoke only in designated areas, after washing your hands
correctly.
5. All staff should be informed of dangers of Weil’s disease.
6. Wear PPE.
eight2O Visual Standards
27. Asbestos
Creating better results together 32
Asbestos fibres can cause lung cancer and lung diseases.
Asbestos could be present in buildings built or refurbished before the year 2000 !
Disturbance of asbestos cement containing materials
through cutting, drilling, and other activities may result in
elevated levels of airborne asbestos fibres.
• Before you start work ask 'Has the site been checked for
asbestos?
• If you come across any hidden or dusty materials which you
suspect may contain asbestos, stop work and get advice.
Identification of asbestos containing materials is not easy and you
can only be sure they are asbestos if they have been tested by a
specialist laboratory.
• Under no circumstances shall the cutting of asbestos
cement pipes be carried out on site without a full
assessment of the need to do so agreed.
• Asbestos pipes can be abandoned and left in the ground as intact
pipes provided that the presence of the asbestos is recorded on
corporate records and that information is passed to other utility
companies or others in response to pipe location requests
eight2O Visual Standards
28. Hand held plant operation
Creating better results together 33
• Is there an alternative method? Carry out Risk Assessment.
• Do not operate vibratory plant if you have been diagnosed with HAVS. Seek advice from your manager
• All plant and equipment must be approved, tested and in date.
Always consider Members of the Public
PPE to be worn when operating or working next to a Pneumatic Breaker/Whacker/Core Drill/Road, Saw/Disc Cutter:
hard hat
safety glasses
high visibility clothing (flame retardant)
overalls (flame retardant)
Gloves
steel toe capped boots
ear defenders
dust mask (as required).
• Daily plant checks must be undertaken
and weekly report provided
• All oil, fuel and other chemical containers
must be labelled and kept within drip
trays when not in use
• Take care when refuelling/filling plant
and handling chemicals
• Carry a spill kit
• Weekly plant inspection reports to be provided
eight2O Visual Standards
29. Tools and equipment
Creating better results together 34
Only use approved tools and equipment
issued or hired by the company. Before
selecting the tools or equipment you must
ensure the following:
• It is suitable for the job/task in hand
• You are authorised and trained to use it
• It is appropriate for the work location e.g.
flammable atmospheres, adverse weather
conditions (wet conditions) and the proximity
of the public and other workers.
Before you use any equipment you must:
• Check for and report any defects or damage
(If it is not safe to use do not start work until a
replacement tool has been obtained.
• Check equipment is in date,
maintained/calibrated as required and make
sure you are familiar with the control.
When using any tools or equipment you must
ensure that:
• All necessary guards are in place and properly
adjusted and all appropriate PPE is worn.
• Report any defects to Supervisors/Stop work
when damage of equipment occurs.
eight2O Visual Standards
30. Cut Off saw use
Creating better results together 35
Always consider Member of the Public
PPE that must be worn during cutting operations:
Hard hat
Safety goggles
High visibility clothing (flame retardant)
Overalls (flame retardant)
Gloves
Steel toe capped boots
Ear defenders
Dust Mask – P3 filter
• Is there an alternative method of cutting?
• Risk Assessment/ Method Statement & Permit to Break Surface in place/signed and understood?
• Abrasive wheels training to be provided to operators changing the blade
• Ensure the correct blade is used
• Dust suppression to be used
• Under no circumstance shall guarding be removed or altered
• Equipment shall not be drop started
• Equipment shall not be moved until the blade has stopped
• Tie back loose clothing/long hair
• In the event of a fuel or oil leak switch the machine off immediately and use a spill kit
• Do not refuel whilst engine is hot
eight2O Visual Standards
31. Vacuum excavator / air lance
Creating better results together 36
• PPE that must be worn during Vacuum Excavator Operations.
Hard hat.
Safety glasses.
High visibility clothing (flame retardant).
Overalls (flame retardant).
Gloves.
Steel toe capped boots.
Ear defenders.
• Always maintain safe working distances between over head lines and the vacuum excavator.
• Operative must be 3m from the container before tipping commences.
• If needing to access the top of the vehicle always try to work from a suitable platform if possible or ensure that fall
restraint systems are used.
• When operating an Air Lance in conjunction with the vacuum excavator or compressor, a ‘Forestry Guard’ must also be
worn.
• Access to the work zone should be prohibited at all times
when the Soil Pick is in use.
• Ensure whip checks are used.
• Vacuum Excavator must be FORS compliant.
eight2O Visual Standards
32. Excavation safety
Creating better results together 37
Refer to Thames Water Essential Standard 1 – Excavation !HIGH RISK ACTIVITY
There is NO safe minimum depth of excavation
Always consider safety of members of the public - Fence off all excavations & work places to prevent pedestrians and vehicles
from entering the work area or being struck. Consider vulnerable people and children.
• Consult Site Survey/ Service Location Drawings
• Competent person to supervise the work/all operatives receive clear instruction on working safely in excavation.
• Risk Assessment/Method Statement/permit to break surface/PPE/Emergency Plan in place before any works are undertaken
• Avoid underground services – use data logging CAT & Generator
• Use safe digging practices, i.e. locate and dig trial holes by hand – no machines/ hand held power tools within 500mm of a service
• All works must be inspected daily and where excavations are left open overnight or for long periods precautions must be undertaken
(backfilling or securely covering excavations) to prevent collapse or unauthorised access. Written weekly report available.
• Excavations must be well lit/ securely fenced/covered or backfilled overnight and at weekends.
• Traffic management in compliance with NRSWA.
• Access - provide a proprietary or ladder access . Where provided, ladders must be regularly inspected, in good order and secured. All
exposed services are supported and never to be used for access and egress to the excavation.
• Exhaust fumes – petrol/diesel powered equipment not to be sited in, or near the edge of an excavation unless fumes can be ducted
away or the area can be ventilated.
• Influx of water controlled by the use of pumps after the water has been channelled into sumps.
• Never work underneath an excavator (no operative in excavation when excavator in use).
• Never enter an unsupported trench where there is a risk of collapse & never work outside the protection of trench boxes or trench
supports.
• Ensure excavations do not affect the footings of scaffolds/ foundations of nearby structures – does the structure need support before
excavation starts? (Site Survey)
• Do not store spoil or other materials close to the sides of excavations.
• Make sure the edges of the excavation are protected against falling materials/people - toe boards/ guard rails where necessary.
• Ensure that plant does not work too close to the edge of an excavation. Use brightly painted baulks or barriers to mark.
• Where vehicles have to tip materials into excavations, use stop blocks to prevent them from over-running. Remember that the sides of the
excavation may need extra support.
eight2O Visual Standards
33. Excavation support
Creating better results together 38
• Temporary support – Before digging any trench pit, tunnel, or other excavations, decide what temporary support will be
required and plan the precautions to be taken.
• Battering the excavation sides – Battering the excavation sides to a safe angle of repose may also make the excavation
safer. In granular soils, the angle of slope should be less than the natural angle of repose of the material being excavated.
In wet ground a considerably flatter slope will be required.
• Any excavations over 1.2m deep or adjacent to live a carriageway will require a ‘Stop and Assess’ approach be
undertaken where appropriate support to prevent collapse must then be considered which must have appropriate
temporary works sign off from a competent person.
• Risk assess excavations less than 1.2 m prior to entry as even work in shallow trenches can be dangerous. You may need
to provide appropriate support if the work involves bending or kneeling in a shallow trench.
• Never work ahead of the support.
Stop blocks used to prevent vehicle from over-running
eight2O Visual Standards
34. Temporary Works
Creating better results together 39
Consult Thames Water Essential Standard No 20 - Management of Temporary Works
Class 1 TW have the highest risk and must be designed by a trained and competent person. To ensure that the design has been carried
out correctly an independent competent designer, familiar with high risk temporary works, must be appointed as the TW design checker for
these works.
Class 2 TW are lower than class 1 TW but still represent a significant risk which needs to be properly addressed and managed.
* A typical list of class 1 & 2 TW is available in Essential Standard No 20 - Management of Temporary Works
Key appointments (in writing):
• TW Designer - any person who prepares or modifies the design of any temporary works.
• TW Supervisor - a competent person who is responsible for supervising the construction/alteration and inspection of TW prior to their
first use or following any alteration.
• TW Coordinator - a competent person with responsibility for the co-ordination of all activities related to TW. Responsible for maintain a
register of designs and maintaining and making available all relevant information for each design.
1. Design Brief & Design to be prepared
2. All designs for high/medium risk TW must be checked by a competent person (someone other than the designer who was not
involved in the original design) prior to construction and prior to any alteration.
3. Any TW that falls under class 1 must have been signed off by a competent person other that the TW Supervisor assigned to the activity.
4. TW Supervisor must:
ensure construction of TW is in accordance with the agreed design
confirm to TW Coordinator that the temporary works meet the design criteria
Inspect TW immediately before use (and after any significant change) for defects
Issue the permit to load/use as appropriate
Supervise its use to ensure it is used safely
Supervise the dismantling of the temporary works
The TW Coordinator & TW Supervisor must always have the authority to cancel the permit to use/ oad and immediately prevent
the further use of the temporary works if deemed unsafe.
eight2O Visual Standards
35. Moling operations
Creating better results together 40
• PPE required:
Hard hat.
Safety glasses.
Ear defenders.
Dust mask – P3 filter.
Flame retardant clothing.
High visibility jacket (flame retardant).
20 kVA Di electric gloves (formal inspection 6 monthly)
Over gloves.
20 kVA Di electric boots.
• Team to be trained to use a mole
• Risk Assessment to be undertaken/Permit to Break Surface
• Before conducting any moling operations ensure the pre-start permit is completed and authorised by a supervisor
• Check utility drawings/Visually check the area for indication of buried services
• Trace the moling area using data logging CAT & Generator
• Expose all buried services (electric, gas, street lighting, cable TV, BT, water etc.)
• Check if ground condition are suitable for moling
• Identify suitable moling route leaving at least 300mm clearance from parallel electric cables and 250mm clearance from
other parallel services
• Identify direction of mole (towards the lowest risk area)
• Mark the distance to be mole on the mole house
• Inspect your PPE
eight2O Visual Standards
36. Drilling walls/panels
Creating better results together 41
• Risk Assessment & Permit to Break Surface signed and understood?
• ALWAYS check for the presence of cables with an approved cable location device.
• Prior to drilling or cutting any surface use the approved:
Bosch GMS120 Locator
Bosch D-Tect 150 Locator.
• Risk Assessment is required whenever working within 500mm of any services or apparatus.
• All electrical power tools used on site will need to be approved and PA Tested.
eight2O Visual Standards
37. Service laying minimum standards
Creating better results together 42
• Relay services to original position where possible.
• Lay pipe in a way that minimises risk of damage by a third party.
• Ensure distances between top tees and joints are in accordance with procedures.
• Service must be laid at right angles to the main and in a straight line.
• Only Use sticks/straight pipes for open cut road crossing (not coiled pipe).
• Marker tape to be used.
• Ensure adequate clearance over/under other services.
• Reference service from a permanent feature.
eight2O Visual Standards
38. Tools for cutting Pipework – Part 1.
Creating better results together 43
eight2O Visual Standards
38. Tools for cutting Pipework – Part 2.
Creating better results together 44
eight2O Visual Standards
38. Tools for cutting Pipework – Part 3.
Creating better results together 45
* Asbestos should only be cut with non‐powered tools. Damping/wetting of surfaces should still be
utilised to ensure no airborne fibres are released.
Where powered mechanical cutting is identified as the only option this must be referred to HS&W Team
as this will potentially be ‘licenced’ work requiring a specialist contractor.
eight2O Visual Standards
38. Tools for cutting Pipework – Part 4.
Creating better results together 46
* Not to be used to cut
pipework
Cut Off Saw
eight2O Visual Standards
39. COSHH Products
Creating better results together 47
Everyday at work you may come into contact with substances that can
be hazardous to your health or the environment. These products include
common substances in everyday use such as paint, bleach, solvent or
fillers.
• Regulations require these substances to be clearly labelled.
• The labels advise the user of the harmful affects the substance may
cause.
• Since 2009, new international symbols have been gradually replacing the
European symbols. Some of them are similar to the European symbols,
that you are already familiar with, but there is no single word describing
the hazard. Read the hazard statement on the packaging and the safety
data sheet from the supplier.
• Remember – know your substances and if in doubt ask.
• Refer to the COSHH assessments.
• Right level of PPE for the hazard including RPE.
• Spill kits to be in place.
• All vehicles to carry signed COSHH assessments and MSDS for all
materials carried.
eight2O Visual Standards
40. Environmental
Creating better results together 48
• Wet cutting technology
• Manage mud/do not leave slip hazards
• Remove waste from site setup and keep tarmac segregated
• Clean your tools as you go – don’t use diesel
• Oil, fuel and other chemical containers must be labelled and kept stored in
drip trays
• Carry a spill kit and ensure it is ready to be used
• Sweep up site after work – use RPE when sweeping.
• Use funnel when re-fuelling plant
• Noise under control and as per consent issued
eight2O Visual Standards
41. Use of Mobile Phones
Creating better results together 49
Key points
• Avoid incidents by using mobile phone
ONLY is designated Mobile Phone Safety
Zones!
Mobile Phone Safety Zone
Operative distracted/
High risk of injury!
eight2O Visual Standards
42. Housekeeping on site
Creating better results together 50
Ensure the safety of the public and your team
• All trimmings and waste must be removed from site
• Stored materials and plant must be guarded
• Plant and equipment must be kept within barriers whilst working
• All oil, fuel other chemical containers must be labelled and kept
within drip trays when not in use
• Spill kit must be available
eight2O Visual Standards
43. Working with Tipper Raised
Creating better results together 51
• Do not enter under tipper when raised
• Guard the tipper when raised
• Do not climb onto the flatbed when raised
• Drop the flatbed as soon as possible
• Remove any unsecured equipment before raising tipper
eight2O Visual Standards
44. Road roller and other towed plant
Creating better results together 52
• Check for oil leaks
• Check oil level daily
• Tow safely – correct number plate, raised jockey wheel, break-away
cable attached , lights in place and working
• Ensure a red warning triangle is attached to overlapping handle
eight2O Visual Standards
45. Rammer
Creating better results together 53
• Check for oil leaks
• Keep stored in a drip tray when not in use
• Two man lift only
• Vibration dosemeter is to be used
Always consider safety of your colleagues and members of the
public
eight2O Visual Standards
46. Quality & Pride in your workmanship – Edge Preparation
Creating better results together 54
• All bound edges shall be essentially straight, smooth and vertical.
• Cut back edges to correct angles - The internal corners and edges of a reinstatement shall be as square as possible.
Internal angles less than 90° are acceptable and, where this is the case, appropriate compaction equipment shall be used to
achieve the specified compaction.
• Individual projections not to be less than 250 mm length, measured parallel to the nominal centreline of the trench.
• All edges shall be adequately prepared prior to application of edge sealant e.g. free of contamination, loose material, and
the like. In all cases the manufacturer’s instructions shall be followed.
• Cut back to existing street furniture/trenches
eight2O Visual Standards
47. Quality & Pride in your workmanship – Edge Proximity to other Apparatus
Creating better results together 55
Carriageway: Where the trimmed edge of your excavation is within 250mm of the road edge/kerbing/drains, manhole
covers/other reinstatements etc. you must extend the trim line to include the feature.
Footpaths/cycle tracks: Where trim-lines for the reinstatement edges are within 150mm of the road
edge/kerbing/drains, manhole covers/other reinstatements etc., the trim lines should be extended to include the
feature. Only the surface course of this extra area needs to be excavated and reinstated (provided the lower layers have
not been damaged).
eight2O Visual Standards
48. Quality & Pride in your workmanship – Compaction
Creating better results together 56
Compaction requirements for Bituminous Mixtures
eight2O Visual Standards
49. Quality & Pride in your workmanship – Compaction
Creating better results together 57
• 4 passes in the footpath for each layer • 6 passes in the road for each layer
eight2O Visual Standards
50. Quality & Pride in your workmanship – Compaction
Creating better results together 58
1. Surround to apparatus fine-fill compacted with 10kg
hand hammer, 6 passes every 100mm
2. Backfill GSB Type 1 compaction whacking foot, 4
passes for each 100mm depth
3. 60mm Binder course 20mm dense macadam
compaction whacking foot, 7 passes every 60mm
depth
4. 40mm surface course compacted with twin drum
roller, 5 passes every 40 mm depth
5. Edge preparation 10kg hand rammer
6. Coated chippings. All chippings shall be 14mm or
20mm size, pre-coated. Where chippings are to be
embedded into road surface they must be spread to
match the existing surface
7. The bituminous overlay shall not be laid until the
cured road slab has achieved a crushing strength of
25N/mm2.
eight2O Visual Standards
51. Quality & Pride in your workmanship – Over-banding
Creating better results together 59
• Overbanding to be BBA/HAPAS approved
• Only undertake over-banding where approved by local council
• Overbanding should not be more than 3mm thick or 40mm wide.
• Hot-applied overbanding to the correct method of work and temperature that depends on the type of material used.
Overbanding should not be applied in the following situations:
• Wet road surface conditions (although some products can be used on damp surfaces – check with Supervisor)
• Low temperatures (Should not be applied below a minimum air temperature of +5°C)
• High temperature (Should not be applied above a maximum air temperature of +30°C)
eight2O Visual Standards
52. Quality & Pride in your workmanship – Pavement Slabs
Creating better results together 60
• Stack slabs flat/avoid manual handling
• Check that all necessary materials are on site
• Damaged modules will need to be replaced
• Check the sub-base level is the correct tolerance
• Match and place modules to fit existing layout or bond
• Remove excess materials from surface
eight2O Visual Standards
53. Quality & Pride in your workmanship – Don’t leave Hazards behind
Creating better results together 61
eight2O Visual Standards
54. Quality & Pride in your workmanship – Don’t leave Hazards behind
Creating better results together 62
eight2O Visual Standards
55. Quality & Pride in your workmanship – Completion of Reinstatement Works
Creating better results together 63
• On completion of works speak to the customer and ask customer if they are satisfied with
your work
• If so leave a “Completion of Reinstatement” card with relevant fields completed
• Date and time are very important
eight2O Visual Standards
56. Quality & Pride in your workmanship – Dealing with an unhappy customer
Creating better results together 64
• Contact your supervisor with details of the problem immediately • Explain to the customer that your supervisor will be in touch • Give the customer your Supervisors name • Remember courtesy and good manners at all times