PERFORMANCE EVALUATION OF WELLS WITH
SINGLE AND MULTIPLE FRACTURES IN TIGHT
FORMATIONS
A Thesis
Submitted to the Faculty of Graduate Studies and Research
In Partial Fulfillment of the Requirements
For the Degree of
Master of Applied Science
In
Petroleum Systems Engineering
University of Regina
By
Feng Zhang
Regina, Saskatchewan
August, 2013
Copyright 2013: F. Zhang
UNIVERSITY OF REGINA
FACULTY OF GRADUATE STUDIES AND RESEARCH
SUPERVISORY AND EXAMINING COMMITTEE
Feng Zhang, candidate for the degree of Master of Applied Science in Petroleum Systems Engineering, has presented a thesis titled, Performance Evaluation of Wells With Single and Multiple Fractures in Tight Formations, in an oral examination held on August 9, 2013. The following committee members have found the thesis acceptable in form and content, and that the candidate demonstrated satisfactory knowledge of the subject material. External Examiner: Dr. Adisorn Aroonwilas, Industrial Systems Engineering
Supervisor: Dr. Daoyong Yang, Petroleum Systems Engineering
Committee Member: Dr. Farshid Torabi, Petroleum Systems Engineering
Committee Member: Dr. Yongan Gu, Petroleum Systems Engineeing
Chair of Defense: Dr. Kelvin Ng, Environmental Systems Engineering
i
ABSTRACT
Hydraulic fracturing technology together with horizontal wells leads to the
exploration and development of unconventional resources economically feasible. Due to
complex fracture network and geology nature, evaluating performance of fluids flow in
such a hydraulic fracture system is really a challenge. Numerical modeling and
simulation usually requires very fine grid to reduce the truncation error and enhance the
simulation accuracy. Sometimes even with fine grid, the associated computation accuracy
is compromised. On the other hand, numerous studies have been conducted on pressure
transient analysis with analytical and/or numerical methods, though some underlying
mechanisms have not been well understood since fluid flow in such tight formations can
be completely dependent on the fracture network while the matrix only plays a source
role. Therefore, it is of fundamental and practical importance to evaluate performance of
a well with single and multiple fractures in a tight formation.
Theoretically, a semi-analytical method is developed to couple the fluid flow in the
matrix and the fracture so as to improve the accuracy and efficiency of pressure transient
analysis in a tight formation. As for the semi-analytical method, the fracture is firstly
discretized into several small segments. Equations for the matrix and fracture system can
be solved in the Laplace domain with source functions, respectively. Continuity equations
can be obtained along the fracture interface, leading to a linear system. Solving the linear
system, the flux in each segment can be obtained, which is substituted into the first
segment to determine the bottomhole pressure in the Laplace domain. Finally, the
Stephest inverse algorithm can be employed to convert the solutions in the Laplace
domain to those in the real time domain. The widely-accepted point source function is
ii
used to describe the fluid flow in the matrix for a vertical well with a single fracture,
while a novel slab source function in the Laplace domain is developed to achieve the
same purpose for a horizontal well with multiple fractures. Compared to the point source
function, slab source function is more general, which attributes geometry in each
direction and considers the pressure effect inside the source by superposition principle.
The non-Darcy flow effect inside the fracture based on the Barree-Conway model is
solved by introducing the pseudo-time and iterative methods.
The semi-analytical method using source functions has been validated with
numerical simulation method and field case, respectively. Subsequently, two
dimensionless parameters, i.e., relative minimum permeability (kmr) and non-Darcy
number (FND), have been introduced to incorporate the non-Darcy effect on flow
performance for a vertical well with single fracture. Compared with the Forchheimer’s
equation, the Barree-Conway model causes a smaller pressure drop at a higher non-Darcy
number. The fracture conductivity would be underestimated when non-Darcy flow exists
inside the fracture. For a horizontal well with multiple fractures, fracture conductivity,
fracture stages, fracture number, and fracture dimension are discussed under
consideration of both non-Darcy effect and partially penetrating ratio. Compared to the
vertical well with single fracture, non-Darcy effect in a horizontal well with multiple
fractures can cause a larger pressure drop as non-Darcy number is increased and relative
minimum permeability is decreased. The partially penetrating ratio greatly affects the
early well response, which leads to an early radial flow regime when the ratio is set to be
a small value. Finally, the newly proposed method has been successfully extended to
determine the reservoir and fracture parameters in a real field case.
iii
ACKNOWLEDGEMENTS
I would like to express my sincere gratitude to my academic supervisor, Dr.
Daoyong (Tony) Yang, for providing me the precious opportunity together with his
continuous encouragement and support throughout the course of my graduate studies.
I also wish to thank the following individuals or organizations for their support and
friendship during my MASc studies at the University of Regina:
My past and present research group members: Dr. Huazhou Li, Mr. Sixu Zheng,
Mr. Yin Zhang, Ms. Xiaoli Li, Mr. Deyue Zhou, Mr. Chengyao Song, Ms. Min
Yang , and Ms. Ping Yang;
Mr. John Styles for providing the transient pressure data and valuable technical
discussions;
Natural Sciences and Engineering Research Council (NSERC) of Canada for a
Discovery Grant to Dr. Yang;
Petroleum Technology Research Centre (PTRC) for the innovation fund to Dr.
Yang;
Faculty of Graduate Studies and Research (FGSR) at the University of Regina for
awarding the FGSR Graduate Scholarship (2012 Winter and 2012 Fall); and
Many wonderful friends and families who extended their care, support and
friendship to me during my stay in Regina.
iv
DEDICATION
This thesis is dedicated to my dearest parents, Mrs. Xiuwen Ji and Mr. Youjin
Zhang, for their continuous support and love.
v
TABLE OF CONTENTS
ABSTRACT… .................................................................................................................... i
ACKNOWLEDGEMENTS ............................................................................................ iii
DEDICATION .................................................................................................................. iv
TABLE OF CONTENTS ................................................................................................. v
LIST OF TABLES ......................................................................................................... viii
LIST OF FIGURES ......................................................................................................... ix
NOMENCLATURE ........................................................................................................ xii
CHAPTER 1 INTRODUCTION .................................................................................... 1
1.1 Unconventional Resources ................................................................................. 1
1.2 Pressure Transient Analysis ............................................................................... 2
1.3 Importance of Non-Darcy Flow ......................................................................... 3
1.4 Purpose of This Thesis Study ............................................................................. 5
1.5 Outline of the Thesis .......................................................................................... 5
CHAPTER 2 LITERATURE REVIEW ........................................................................ 7
2.1 Source and Green Function ................................................................................ 8
2.1.1 Point source function .................................................................................. 8
2.1.2 Volumetric source function ........................................................................ 9
2.1.3 Slab source function ................................................................................. 10
2.2 Pressure Transient Analysis ............................................................................. 11
2.2.1 Vertical well.............................................................................................. 12
2.2.2 Horizontal well ......................................................................................... 15
2.3 Non-Darcy Flow ............................................................................................... 17
vi
2.4 Summary .......................................................................................................... 22
CHAPTER 3 DETERMINATION OF FRACTURE CONDUCTIVITY IN TIGHT
FORMATIONS WITH NON-DARCY FLOW BEHAVIOUR .......... 24
3.1 Theoretical Model ............................................................................................ 26
3.1.1 Mathematical formulation ........................................................................ 26
3.1.2 Semi-analytical solution ........................................................................... 29
3.1.3 Continuity conditions ............................................................................... 33
3.2 Model Validation .............................................................................................. 36
3.2.1 Forchheimer equation ............................................................................... 36
3.2.2 Numerical simulation................................................................................ 41
3.3 Sensitivity Analysis .......................................................................................... 41
3.3.1 Relative minimum permeability (kmr) ....................................................... 44
3.3.2 Non-Darcy number (FND) ......................................................................... 46
3.3.3 Comparison ............................................................................................... 46
3.4 Effect of Non-Darcy Flow ................................................................................ 50
3.4.1 Tight oil formations .................................................................................. 53
3.4.2 Tight gas formations ................................................................................. 62
3.5 Case Study ........................................................................................................ 67
3.6 Summary .......................................................................................................... 67
CHAPTER 4 SLAB SOURCE FUNCTION FOR EVALUATING
PERFORMANCE OF A HORIZONTAL WELL WITH MULTIPLE
FRACUTRES .......................................................................................... 70
4.1 Mathematical Formulation ............................................................................... 72
vii
4.1.1 Product principle ....................................................................................... 73
4.1.2 Slab source function ................................................................................. 74
4.2 Linear System ................................................................................................... 79
4.2.1 Constraint equations ................................................................................. 80
4.2.2 Flow equations .......................................................................................... 81
4.2.3 Continuity equations ................................................................................. 82
4.2.4 Wellbore equations ................................................................................... 83
4.3 Model Validation .............................................................................................. 83
4.4 Results and Discussion ..................................................................................... 87
4.4.1 Fracture stages .......................................................................................... 87
4.4.2 Fracture conductivity ................................................................................ 91
4.4.3 Fracture length .......................................................................................... 93
4.4.4 Fracture spacing ........................................................................................ 96
4.4.5 Penetrating ratio ........................................................................................ 96
4.4.6 Non-Darcy effect ...................................................................................... 98
4.5 Case Study ...................................................................................................... 106
4.6 Summary ........................................................................................................ 113
CHAPTER 5 CONCLUSIONS AND RECOMMENDATIONS ............................. 114
5.1 Conclusions .................................................................................................... 114
5.2 Recommendations .......................................................................................... 116
REFERENCES .............................................................................................................. 118
viii
LIST OF TABLES
Table 3.1 Basic parameters used for simulating pressure-transient response in a tight gas
formation (Vincent et al., 1999; Settari et al., 2000; Gill et al., 2003) ............ 39
Table 3.2 Basic parameters used for simulating pressure transient response .................. 42
Table 3.3 Basic parameters used for simulating pressure-transient response in a tight oil
formation .......................................................................................................... 51
Table 3.4 Basic parameters used for simulating pressure-transient response in a tight gas
formation .......................................................................................................... 52
Table 4.1 Basic instantaneous source functions in an infinite slab reservoir (Chen et al.,
1991) ................................................................................................................. 75
Table 4.2 Values of h(sn)/g'(sn) and (sn, n=0,1,...) for instantaneous plane sources in an
infinite slab reservoir (Chen et al., 1991) ......................................................... 76
Table 4.3 Basic parameters used for simulating pressure transient response .................. 84
Table 4.4 Parameters used for describing non-Darcy flow with Barree-Conway model in
multiple fracutures (Lai et al., 2012) .............................................................. 101
Table 4.5 Reservoir and fracture properties for the well in the Bakken formation ........ 107
Table 4.6 Type curve matching results for the buildup test ........................................... 111
ix
LIST OF FIGURES
Figure 3.1 Schematic diagram of a vertical hydraulic fracture in a closed cylindrical
reservoir. ...................................................................................................... 25
Figure 3.2 Schematic of discretization of one fracture in the global fracture subsystem. 31
Figure 3.3 Flowchart of solving the non-linear system. .................................................. 35
Figure 3.4 The coefficient matrix for solving the matrix-hydraulic fracture system in the
single fractured vertical well. ...................................................................... 37
Figure 3.5 Model validation for the Forchheimer equation ............................................. 40
Figure 3.6 (a) Top view of the 3D grid system and (b) Model validation between this
study and CMG simulation results. ............................................................. 43
Figure 3.7 Effect of non-Darcy number FND (a) at FND = 100, and (b) at FND = 5. ......... 45
Figure 3.8 Effect of non-Darcy number FND (a) at kmr = 0.01, and (b) at kmr = 0.10. ...... 47
Figure 3.9 Comparison on dimensionless pressure calculated from the Forchheimer
equation and the Barree-Conway model together with the relative errors. . 48
Figure 3.10 Type curves for non-Darcy effect in a tight oil formation at CfD = 100.0. ... 54
Figure 3.11 Flux distribution from the matrix to the fracture in a tight oil formation at
CfD = 100 and FND =22.001. ......................................................................... 56
Figure 3.12 Flux distribution inside the fracture in a tight oil formation at CfD = 100 and
FND =22.001. ................................................................................................ 57
Figure 3.13 Type curves for non-Darcy effect in a tight oil formation at CfD = 20.0. ..... 59
Figure 3.14 Flux distribution from the matrix to the fracture in a tight oil formation at
CfD = 20.0 and FND =22.001. ........................................................................ 60
Figure 3.15 Bilinear flow analysis (a) at CfD = 20.0, and (b) at CfD = 100.0. .................. 61
x
Figure 3.16 Type curves for non-Darcy effect in a tight gas formation at CfD = 100.0. .. 63
Figure 3.17 Flux distribution from the matrix to the fracture in a tight gas formation at
CfD = 100.0 and FND =121.328. .................................................................... 64
Figure 3.18 Type curves for non-Darcy effect in a tight gas formation at CfD = 20.0. .... 65
Figure 3.19 Flux distribution from the matrix to the fracture in a tight gas formation at
CfD = 20.0 and FND =121.328. ...................................................................... 66
Figure 3.20 Type curve match for the field data on an oil well in a tight formation ....... 68
Figure 4.1 Schematic diagram of a horizontal well with multi-stage fractures in a box-
shaped reservoir ........................................................................................... 71
Figure 4.2 Schematic of a slab source model ................................................................... 77
Figure 4.3 The coefficient matrix for solving the matrix-hydraulic fracture system ....... 85
Figure 4.4 (a) Top view of the 3D grid system and (b) Cross-section of the 3D grid
system .......................................................................................................... 86
Figure 4.5 Model validation between this study and CMG simulation results ................ 88
Figure 4.6 Comparison between this study and CMG simulation results ........................ 89
Figure 4.7 Effect of fracture stages on the well response with the same fracture length. 90
Figure 4.8 Pressure response together with its derivative for five pairs of fractures under
various fracture conductivities ..................................................................... 92
Figure 4.9 Effect of fracture conductivity on the flow distribution at (a) tD = 1.0E-6, and
(b) tD = 1.0E2 ............................................................................................... 94
Figure 4.10 Effect of fracture length on the well response at four pairs of fractures ...... 95
Figure 4.11 Effect of fracture spacing on the well response at four pairs of fractures .... 97
xi
Figure 4.12 Effect of partially penetrating ratio of three stages at CfD=10 and (a) α>0.5,
and (b) α≤0.5 .............................................................................................. 99
Figure 4.13 Effect of non-Darcy number FND (a) at kmr = 0.01, and (b) at kmr = 0.10 ... 102
Figure 4.14 Effect of non-Darcy number kmr at (a) FND = 1000, and (b) FND = 10 ....... 103
Figure 4.15 Effect of non-Darcy flow on the flow distribution at (a) tD = 1.0E-6, and (b)
tD = 1.0E3 ................................................................................................... 105
Figure 4.16 Pressure buildup test and production history .............................................. 108
Figure 4.17 Flow regime interpretation for the pressure buildup response ................... 109
Figure 4.18 Type curve matching of pressure buildup data ........................................... 112
xii
NOMENCLATURE
Notations
Bg = formation volume factor, bbl/STB or bbl/Mscf
b = coefficient defined in Eq. [3.23a]
CD = dimensionless wellbore storage
Cf = fracture conductivity, mD·ft
Cη = fracture diffusivity, fraction
c = coefficient defined in Eq. [3.23b]
ct = total compressibility, psi-1
d = coefficient defined in Eq. [3.23c]
E = parameter defined in Eq. [2.4]
f1, f2 = two function defined in Eq. [4.2]
Fn, Fm = parameter defined in Eqs. [4.9d] and [4.9e]
,
,
m n
i jF = parameter defined in Eq. [A-11]
FND = non-Darcy number defined in Eq. [3.9c]
h = payzone thickness, ft
hf = fracture height, ft
k = permeability, mD
kapp = apparent permeability, mD
xiii
kd = constant Darcy permeability, mD
kmin = minimum permeability at high rate, mD
kmr = relative minimum permeability, fraction
kr = relative permeability, fraction
L = length, ft
Lr = reference length, ft
NRe = Reynolds number, dimensionless
p = pressure, psi
qf = flux from reservoir to fracture along fracture, STB/(d·ft) or Mscf/(d·ft)
qN = flux at the node, STB/d or Mscf/d
Qsc = surface flow rate, STB/d or Mscf/d
Qmax = maximum flow rate desired, STB/d or Mscf/d
R = residue of function f1 in Laplace domain at pole sn
s = Laplace transform variable
sn = pole of function f1 in Laplace domain
S = parameter defined in Eq. [A-2]
Sf = parameter defined in Eq. [A-1]
Sg = gas saturation, fraction
Sp, Sp(m), Sp(n), Sp(nm) = parameter defined from Eqs. [4.9a] to [4.9d]
xiv
t = time, hr
V = parameter defined in Eq. [3.25]
v = velocity, ft/s
wf =fracture width, ft
x = x coordinate, ft
xf = fracture half length, or half-length of a slab source, ft
xw = well location, ft
y = y coordinate, ft
yf = half-width of a slab source, ft
z = z coordinate, ft
zf = half-height of a slab source, ft
Greek letters
p L = potential gradient, psi/ft
α = penetrating ratio, fraction
αn = parameter defined in Eq. [4.9g]
β = non-Darcy flow coefficient, ft-1
βm = parameter defined in Eq. [4.9h]
η = hydraulic diffusivity
xv
μ = fluid viscosity, cP
ρ = fluid density, lbm/ft3
τ = characteristic length, ft
τD = dimensionless pseudo-time defined in Eq. [3.15]
δ = parameter defined in Eq. [3.4]
= porosity, fraction
Subscript
D = dimensionless
e = external boundary
f = fracture
i = initial condition, or index, ith
node
m = matrix
max = maximum
min = minimum
N = node
w = wellbore
wf = wellbore flowing
xvi
SI Metric Conversion Factors
bbl × 1.589874 E-01 = m3
cp × 1.0* E-03 = Pa·s
ft × 3.048* E-01 = m
mD × 9.869233 E-04 = µm2
lbm × 4.535924 E-01 = kg
psi × 6.894757 E+00 = kPa
*Conversion factor is exact
1
CHAPTER 1 INTRODUCTION
1.1 Unconventional Resources
Unconventional resources (e.g., shale gas, tight gas, tight oil, oilsands, and coalbed
methane) have recently become a significant increasing source of hydrocarbon
production. Physically, unconventional reservoir systems are difficult to produce and
therefore require special completion, stimulation, and production techniques to achieve
economic success. There have encountered numerous technical challenges due to the
inherent low permeability together with complex geological and petrophysical
characteristics.
Canada has extensive exploration and production of unconventional resources.
With the horizontal drilling and multi-stage hydraulic fracturing techniques for low
permeability reservoirs, tight oil production has recently seen a significant increase in the
Bakken formation which extends from North Dakota and Montana in the United States to
Saskatchewan and Manitoba in Canada (Bahrami and Siavoshi, 2013). The typical
Bakken well in Canada produces roughly 210 bbl/d in the first month (NEB, 2012). Till
June 2011, production from the Bakken play reached nearly 400,000 bbl/d in the USA
and 78,000 bbl/d in Saskatchewan and Manitoba of Canada, respectively (USGS, 2012).
Besides the Bakken Formation, tight oil plays highlighted include the Cardium
Formation, Viking Formation, Lower Shaunavon Formation, Montney Formation,
Duvernay Formation, Beaverhill Lake Group, and Lower Amaranth Formation (NEB,
2012). The development of tight oil resources in the Western Canadian Sedimentary
Basin is still in its infancy. In the recent years, the Cardium play in the west-central
2
Alberta has attracted a great deal of attention with an estimated reserves of 305 million
barrels of light oil, while recent drilling activity has shown that the economics, though
attractive, fall short of those in the Bakken play (AGS, 2009).
Much of the past tight gas activity in the Western Canadian Sedimentary Basin has
focused on the plays in the northeast British Columbia (BC), among which the Montney
play is a major discovery (Wood, 2012). Since horizontal drilling with multi-stage
fracturing technology has made some gas wells with production of 5 to 6 MMscf/d, the
Horn River basin continues to move toward the commercial development stage. With
consideration of the uncertainty, the original gas in place is estimated to be 372 to 529
Tscf (NEB, 2012). In eastern Canada, tight gas resources are also discovered in the
Appalachian Basin, Sydney Basin, and Maritimes Basin (USGS, 2012).
1.2 Pressure Transient Analysis
Due to complex fracture networks and geology natures, modeling and simulation of
flow in such a hydraulic fracture system is really a challenge. As for numerical simulation,
it is usually required to reduce the truncation error and enhance the simulation accuracy
by using very fine grid. This often causes large grid numbers and costs huge computer
memory and storage space. Therefore, analytical and semi-analytical methods by the
source approach offer a flexible tool in well performance evaluation (Lin and Zhu, 2012).
In a tight reservoir system, fluid flow behavior near a single fracture can be
described as linear, elliptical, and pseudo-radial flow regimes (Thompson, 1981). An
elliptical solution for the case of an infinite-acting reservoir was proposed for a vertical
well with finite conductivity fracture, though multiple fracture system makes the
3
simulation more complex. An analytical solution was initially proposed by van Kruysdijk
and Dullaert (1989), which introduces the concept “compound linear flow”. It should be
noted that at early production linear flow is dominant, then the flow turns to
perpendicular to the fracture surface until pressure transients of the individual fractures
begin to interfere, leading to a compound linear flow regime (Ilk, 2010). Other analytical
solutions are provided to model the pressure transient behaviour of horizontal wells (Guo
and Evans, 1994; Larsen and Hegre, 1994; Horne and Temeng, 1995). A semi-analytical
method has been developed and applied to model the entire range of flow regimes around
a horizontal well with multiple fractures (Medeiros et al., 2006). In this case, a dual
permeability region surrounding the fractures is assumed to represent complex fractured
region.
1.3 Importance of Non-Darcy Flow
Darcy’s law is considered as the fundamental principle in fluid flow in porous
media. However, the limitations of Darcy’s law constrained to a relatively small velocity
region have long been recognized (Barree and Conway, 2004). Any deviation from the
linear Darcy flow can be considered as non-Darcy flow. Forchheimer (1901) found that
Darcy’s law was inadequate for describing high-velocity gas flow in porous media and
added a new term to account for the additional pressure drop. A constant parameter (i.e.,
β) is proposed to describe the increasing contribution to pressure drop caused by inertial
losses.
Since the β factor was proposed, different mechanisms have been discussed to
explain the non-Darcy flow in the Forchheimer’s model. Since Non-Darcy flow is
4
attributed to turbulence, β is also called the turbulence factor. Most researchers still agree
that Forchheimer non-Darcy flow is not resulted from turbulence other than inertial
effects because non-Darcy flow is found to occur even at a low Reynolds number (Barak,
1987; Ruth and Ma, 1992; Whitaker, 1996).
Many correlations from the experimental data have been proposed to calculate the
inertial factor β (Geertsma, 1974; Frederick and Graves, 1994; Li and Engler, 2001). All
the correlations suggest that inertial factor is highly correlated with permeability: the
lower the permeability is, the larger the inertial factor will be. Although experimental
studies provide a simple and straightforward correlation to obtain the inertial factor value,
field evidences indicate that the β value at the field scale is significantly greater than the
corresponding experimental measurements (Frederick, 1980). It was suggested that the β
value estimated from field observations are much more reliable than those from
experimental measurements (Narayanaswamy et al., 1999).
Even in the Forchheimer model, some data sets could not be described by the
quadratic flow equation (Firoozabadi and Katz, 1979). The Forchheimer plot can become
concave downwards, leading to the observation of a higher apparent permeability than
that predicted by the Forchheimer’s equation at a high velocity (Jones, 1972). A new
model is proposed to replace the inertial factor in the Forchheimer’s model with two new
parameters, i.e., minimum permeability plateau and characteristic length (Barree and
Conway, 2004). According to the experimental measurements, Lai et al. (2012) claimed
that Barree-Conway model is capable of describing non-Darcy flow in a wider velocity
range than the traditional Forchheimer’s model.
5
1.4 Purpose of This Thesis Study
The purpose of this thesis study is to evaluate performance of a vertical well with
single fracture and a horizontal well with multiple fractures in a tight formation. The
primary objectives of this study include:
1) To determine fracture conductivity of a vertical well with single fracture in a
tight formation under non-Darcy effect with the point source function;
2) To develop a novel slab source function in the Laplace domain to accurately
describe the fluid flow in the porous media;
3) To evaluate the non-Darcy flow effects with the Barree-Conway model, and
compare with traditional Forchheimer’s model;
4) To apply the slab source function in the Laplace domain in a horizontal well
with multiple fractures, and then examine effects of fracture conductivity,
fracture dimension, fracture spacing, fracture number, partially penetrating ratio
and non-Darcy flow; and
5) To extend the newly developed techniques for field applications under non-
Darcy effect and subsequently determine the fracture conductivity and non-
Darcy number.
1.5 Outline of the Thesis
This thesis is composed of five chapters. More specifically, Chapter 1 is an
introduction to the thesis topic together with its major research objectives and scope.
Chapter 2 provides an updated literature review on the pressure transient analysis of
6
fractured wells (i.e., single fracture and multiple fractures). It also includes the non-Darcy
flow behaviour in the fracture. Chapter 3 determines the fracture conductivity of a
vertical well with single fracture under non-Darcy effect. Chapter 4 proposes a novel slab
source function and extends its application to describe pressure transient behaviour in a
horizontal well with multiple fractures. Chapter 5 summarizes the major scientific
findings of this study and provides some recommendations for future research.
7
CHAPTER 2 LITERATURE REVIEW
It has long been recognized that unlocking unconventional resources (e.g., tight oil
and shale gas) is uneconomically viable due to the inherent complexity and low
permeability. The recent advances in hydraulic fracturing technology together with
horizontal wells, however, lead to the exploitation and development of unconventional
resources economically feasible. Such a complex system including matrix, horizontal
wells, multiple hydraulic fractures, and natural fractures presents a great challenge to
accurately model and predict its performance, though numerical simulation is a powerful
tool to evaluate the performance of fractured wells in a complex reservoir. In addition, it
is time-consuming for numerical simulation with inherent uncertainties to achieve such a
purpose under conditions of the required ultra-fine grid.
In practice, the source and Green function is widely applied to solve the single-
phase fluid flow in the porous media when the fluid movement is induced from a
complex fractured well system. Especially, point source function over either a line or a
surface has been mostly used for its easy computation. However, limitations have been
noted in the point source function due to the fact that the source dimension and pressure
inside the source have been neglected.
In this chapter, the source and Green functions applied to evaluate performance of
hydraulic fracture systems are firstly reviewed, followed by pressure transient analysis
with single or multiple fractures. Also, non-Darcy effects in the hydraulic fractures are
presented and discussed.
8
2.1 Source and Green Function
Numerous analytical models have been made available to describe the fluid flow in
a tight formation where partial of the respective contribution from matrix, natural and
hydraulic fractures, and horizontal wellbores has been considered. Gringarten and Ramey
(1973) firstly introduced the Green source function to the problem of unsteady-state fluid
flow in such a reservoir. Since a continuous source solution can be obtained by
integrating the response to an instantaneous source solution, the Green function was
introduced under different boundary conditions for a point, line, plane, and slab source,
respectively. The Newman product method under certain initial and boundary conditions
allows the solution of a multi-dimensional problem to be constructed from one-
dimensional solutions (Newman, 1936).
2.1.1 Point source function
Gringarten et al. (1974) applied the point source solution to the unsteady-state
pressure distribution induced by a well with vertical fractures of infinite conductivity.
The fracture is divided into N segments, each of which is assumed to be a uniform flux
source. By using the Green function in the Laplace domain, Cinco-Ley and Samaniego
(1981) developed a vertical fracture model of finite conductivity in an infinite reservoir
so that variable rates, wellbore storage, skin effect, and conductivity can be easily
quantified. A bilinear flow model is then developed to perform pressure transient analysis
for vertical finite conductivity fractures.
9
Babu and Odeh (1988) predicted horizontal well performance in a closed reservoir
under pseudosteady-state condition by integrating the point source function to the line
source function. Ozkan and Raghavan (1991) developed a point source solution in the
Laplace domain together with an extensive library of solutions under various wellbore
configurations, noting that Gringarten and Ramey’s solution becomes limited if one
desires to transform such a solution to the Laplace domain. Due to the fact that the
product solution technique is only applicable in the real time domain, Chen et al. (1991)
developed an approach to derive solutions in the Laplace domain under various wellbore
and boundary conditions by extending the product principle to the Laplace domain.
2.1.2 Volumetric source function
Amini and Valko (2007) distributed the volume source function to evaluate
performance of horizontal wells with multi-stage fractures in a box-shaped reservoir,
making it possible to describe the pressure behaviour inside the source. A source term
was added to the diffusivity equation to calculate the pressure distribution, while the
production rate from a fracture can be calculated. The volumetric source function
provides reliable results in modeling permeability anisotropy, partial penetration of the
source, and additional pressure losses stemming from the particular geometry of the flow
path inside the sources. Zhu et al. (2007) applied the volumetric source model to some
field cases. The volumetric source method was then successfully adjusted to take into
account the non-Darcy flow effect in a horizontal well with multiple fractures by Amini
and Valko (2010), showing that this method is efficient to predict the production
performance and pressure response.
10
2.1.3 Slab source function
After introducing the procedure to develop slab source function with modified
product principle, Chen et al. (1991) applied it to the partially penetrating fracture by
assuming the fracture as a plane source, which is intercepted by two slab sources and one
plane source. Although the fracture is still assumed to be a plane, the slab source function
has been incorporated in a different way such that the point source function is integrated
along a plane.
Ogunsanya et al. (2005) presented a slab source function or the so-called solid bar
source, which was developed in an infinite-acting reservoir with impermeable upper and
lower boundaries. With the assigned dimension in each direction, the bar source function
can be used to analyze pressure transient behaviour of both vertical and horizontal
fracture systems.
Lin and Zhu (2012) developed a slab source method in a closed boundary box-
shaped reservoir to evaluate performance of horizontal wells with and without fractures,
assigning the source to have a three-dimensional (3D) geometry with consideration of the
effect of pressure behaviour inside the sources by using the superposition principle. The
slab source function is derived based on the instantaneous source functions (Gringarten
and Ramey, 1973) with the Newman’s product method. The slab source function is
claimed to be a general source function which is applicable in vertical wells with
fractures, and horizontal wells with and without fractures.
11
2.2 Pressure Transient Analysis
As for an unconventional reservoir, pressure transient analysis for a hydraulically
fractured well plays an important role in not only evaluating well performance, but also
determining its complex reservoir characteristics, including permeability, initial pressure,
wellbore storage, skin factor, fracture dimension, and conductivity. Different flow
regimes that may be present in a well with single or multiple hydraulic fractures are
summarized as follows.
As for a well with a single hydraulic fracture, we have (Brown et al., 2009; Ozkan
et al., 2009):
1) Bilinear flow regime is observed in a finite conductivity fracture with slope of
1/4 on the pressure derivative;
2) Linear flow regime follows the bilinear flow towards the hydraulic fracture
wings surrounding the hydraulic fractures with slope of 1/2 on the pressure
derivative;
3) Elliptical flow regime develops towards the drainage area around the fractures
with slope of 1/3 approximately on the pressure derivative; and
4) Pseudo-radial flow regime appears at a later time when pressure propagates deep
enough into the reservoir with slope of 0 on the pressure derivative.
Comparing to the single fracture case, reservoir flow regimes in a horizontal well
with multiple fractures are much more complicated (Bahrami and Siavoshi, 2013):
1) Radial-linear flow occurs inside the hydraulic fractures;
2) Bilinear/linear flow regime corresponds to the same flow regimes in the single
fracture case with slope of 1/4 and 1/2 on the pressure derivative;
12
3) Early radial flow regime is developed towards each fracture when the spacing
between each fracture and its half length is suitable;
4) Early-boundary-dominated flow regime appears when the stimulated reservoir
volume (SRV) around each hydraulic fracture is depleted. Drainage area around
each hydraulic fracture interferes with those of other fractures. This process is
similar to the boundary effect with slope in a range of 0.5 and 1.0; and
5) Elliptical flow/pseudo radial flow regime is similar to the corresponding flow
regimes in the single fracture case.
Compound linear flow regime shows that the flow pattern is predominantly normal
to the vertical plane that contains the horizontal well (van Kruysdijk and Dullaert, 1989).
It should be noted that one or more flow regimes may not be present, depending on the
magnitudes of the reservoir and fractures. As for a finite reservoir, a boundary dominated
flow regime will appear where closed boundaries are involved.
2.2.1 Vertical well
Numerous efforts have been made to analyze production and pressure data so as to
obtain well/reservoir parameters for a hydraulically fractured vertical well in a low
permeability reservoir (Thompson, 1981; Amini et al., 2007; Cipolla et al., 2009).
Gringarten et al. (1974) developed an analytical solution to the problem of transient fluid
flow in the vertical wells with fractures. Infinite conductivity and uniform flux vertical
fracture cases were presented based on the Source and Green’s functions proposed by
Gringarten and Ramey (1973).
13
Studies on the effect of conductivity on the pressure response of a fractured well
were initiated by Cinco-Ley et al. (1976). A semi-analytical solution was developed to
tackle the problem of transient flow of fluids towards vertical fractures with finite
conductivity. As such, this method separates the reservoir system into two subsystems
(i.e., the fracture and matrix subsystems) which can be solved analytically by using the
Source and Green’s functions. The fracture and matrix solutions are then coupled
together with continuity conditions between the two media to yield a solution for the flux
distribution along the fracture. Type curves of well pressure versus time as dimensionless
terms were generated for analyzing well test data under different dimensionless
conductivities.
After analyzing pressure data of fractured wells, Cinco-Ley and Samaniego (1978)
proposed a new analytical solution for the transient behaviour of wells under low and
intermediate conductivities at the initial production. This solution includes a bilinear flow
regime in which only the transient effects of the region of the matrix surrounding the
fracture can affect the well response. Then, a new correlation for the finite conductivity
fractures was presented by correlating the early flow solutions into a single envelope
curve.
Raghavan et al. (1978) examined the effect of a partially penetrating fracture on the
transient pressure behaviour of a well. An analytical solution was developed by assuming
uniform flux across the fracture. An approximate solution was developed for evaluating
the transient pressure behaviour of a well that intersects a partially penetrating fracture
with infinite conductivity. Rodriguez and Cinco-Ley (1984) studied the unsteady-state
behaviour of a reservoir with a well intersected by a partially penetrating vertical fracture
14
of finite conductivity. A semi-analytical method similar to the Cinco-Ley et al. (1976)
was then developed with consideration of the partially penetrating effect. The flow
behaviour of the partially penetrating fractures during the initial production is equivalent
to that of the totally penetrating fractures. An early infinite-acting flow period was found
to follow the bilinear/linear flow regime.
Cinco-Ley and Meng (1988) introduced a semi-analytical and simplified fully
analytical model to study the transient behaviour of a well intersected by a vertical
fracture in a dual porosity reservoir, respectively. Tiab (1988) proposed a method known
as the “TDS-Tiab’s Direct Synthesis Technique” for pressure transient analysis instead of
the conventional semi-log and log-log type curve matching methods. Tiab (1993) applied
the TDS method to uniform and vertically fractured wells with finite and infinite
conductivity.
Wattenbarger et al. (1998) proposed an effective fracture network length
accounting for a single vertical fracture and obtained the solutions based on the linear
flow concept. The natural fracture network is added to the linear flow solutions to form a
linear dual porosity solution, stating that the linear flow regime should generally be
considered as the major one for shale gas reservoirs (Bello and Wattenbarger, 2010). The
slope of the straight line in the linear flow regime yields the matrix drainage area,
provided that the matrix permeability is known during the transient linear flow regime.
However, the linear flow trend could be subjective and the conductivity may affect the
production behaviour (Ilk, 2010). Amini et al. (2007) provided an elliptical flow solution
for hydraulically fractured vertical wells, while the application of elliptical flow type
curves is presented elsewhere (Ilk et al., 2007).
15
2.2.2 Horizontal well
As for a horizontal well with multiple fractures in a tight formation, it becomes
much more difficult to evaluate its performance with huge uncertainties due to the lack of
fundamental understanding (Bello and Wattenbarger, 2010). van Kruysdijk and Dullaert
(1989) firstly provided an analytical solution to present a compound linear flow regime at
late times. Guo et al. (1994) developed an analytical solution without accounting for the
interference among fractures.
Leif and Hegre (1994) provided a comprehensive investigation of the pressure
transient behaviour of horizontal wells with both single and multiple vertical fractures,
either longitudinal or transverse. In this case, fracture radial, radial-linear, formation
linear and pseudo-radial flow can be observed. After examining the pressure response of
horizontal wells with single and multiple fractures in homogenous systems, Kuchuk and
Habusky (1994) noted that wellbore storage effect cannot be neglected in the low
conductivity fractures.
Horne and Temeng (1995) presented an analytical model for evaluating inflow
performance and transient behaviour of a horizontal well with multiple transverse
fractures. Such pressure transient solutions were firstly developed for a uniform flux
single fracture, and then superposition principle was applied to generate final solutions
for multiple fractures.
Raghavan (1997) developed an analytical solution to discern the response of
horizontal wells with multiple fractures. Based on the analytical model, three significant
flow regimes can be observed: 1) Early flow regime in which the system behaves like the
16
one with n-layers; 2) Intermediate flow regime in which interference between fractures is
reflected; and 3) Late flow regime in which the system behaves like a single fracture.
After carefully examining over 2000 fracture treatments data, Wright et al. (1998)
found that fractures are almost never perfectly vertical. The fractures usually dip 5 to 15
degrees from the vertical and very few fractures dip less than two degrees off the vertical.
Wan and Aziz (1999) developed a general solution for horizontal wells with
multiple fractures. Four flow regimes can be accordingly identified, i.e., the early linear,
transient, late linear, and late radial flow.
Zerzar and Bettam (2003) presented a combined method to couple the boundary
element method and Laplace transformation for the horizontal wells with multiple
fractures. This method includes seven flow regimes, i.e., bilinear, linear, elliptical, radial,
pseudo-radial, second linear, and pseudo-steady flow. Also, Al-Kobaisi and Ozkan (2004)
proposed a hybrid numerical-analytical model for evaluating the pressure transient
response, while effect of the rectangular and elliptical geometry of fractures on pressure
response was examined.
Medeiros et al. (2006) proposed a semi-analytical method to obtain pressure
transient solutions for a heterogeneous system, providing flexibility to model various well
responses in tight reservoirs. Amini and Valko (2007) presented a semi-analytical
solution by using the volume source function to predict the performance of a horizontal
well with multiple transverse fractures in a bounded reservoir.
Ozkan et al. (2009) and Brown et al. (2009) respectively presented a trilinear flow
solution in a dual porosity reservoir to analyze the pressure transient behaviour of
horizontal wells with multiple fractures. Such analytical solutions in the outer reservoir,
17
inner reservoir, and fractures are coupled together on the interfaces between the regions.
Meyer et al. (2010) provided an approximate analytical solution for finite conductivity
multiple fractures including fracture interference.
Al-Rbeawi and Tiab (2012) examined effects of the partially penetrating ratio and
inclined angle for horizontal wells with multiple fractures. An early radial flow regime
can be observed to represent the radial flow around each fracture for scenarios with a
small penetrating ratio. The TDS method was subsequently applied to estimate the
formation and fracture parameters.
2.3 Non-Darcy Flow
Darcy’s law (1856) has laid the foundation for describing the fluid flow in porous
media. As such, the pressure gradient can be related to the fluid viscosity μ and
superficial velocity v in a porous media with constant permeability k, i.e.,
p v
L k
[2.1]
Forchheimer (1901) observed the deviation from Darcy’s law at high flow rates. In
addition to introducing a new parameter called inertial factor, a quadratic flow term was
added to the Darcy’s linear form to account for the deviation from the linearity of the
Darcy’s law. This equation is now commonly referred to as the Forchheimer’s equation,
2+p v
vL k
[2.2]
where β is the inertial flow parameter, and ρ is the density of the fluid.
18
Even in one of the Forchheimer’s publications in 1901, some datasets could not be
described by the quadratic flow equation. Jones (1972) observed that there exists a large
deviation from the linear Forchheimer plot for core samples with a large value of the
inertial factor. The Forchheimer plot becomes concave downward, while the apparent
permeability is calculated to be higher than those predicted by the Forchheimer’s
equation at a high velocity. In spite of its limitations, numerous efforts have been made to
evaluate non-Darcy flow behaviour based on the Forchheimer equation (Andrade et al.,
1997; Hill et al., 2001; Stanley and Andrade, 2001).
Based on the extensive experimental results and field data, Barree and Conway
(2004) proposed a new model by replacing the inertial factor in the Forchheimer’s model
with two new parameters, i.e., minimum permeability plateau and characteristic length. In
this case, the absolute permeability in the Darcy’s law is replaced by the apparent
permeability,
app
p v
L k
[2.3]
where kapp is the apparent permeability which is defined as follows,
min
min
Re1
dapp E
k kk k
N
[2.4]
Due to the introduction of minimum permeability plateau (kmin), apparent
permeability becomes constant at both low (i.e., kd) and high Reynolds number (NRe),
which implies the plateau behaviour. The plateau behaviour at high Reynolds number is
partially validated by Lai (2010). The exponential coefficient E describes the overall
heterogeneity of the test samples. The better the sorting is, the closer the value
19
approaches to 1.0. For single-sieve proppant, the value of E is equal to unity (Barree and
Conway, 2004). In equation [2.4], NRe can be written as follows,
ReN
[2.5]
where τ is the characteristic length. Therefore, coupling Equations [2.3]-[2.5], the Barree-
Conway model can be written as follows,
minmin
1
d
p v
k kxk
v
[2.6]
According to the experimental measurements, Lai et al. (2012) claimed that Barree-
Conway model is capable of describing non-Darcy flow in a much wider velocity range
than that of the traditional Forchheimer’s model.
In a tight formation, long horizontal wells that have been drilled and massively
fractured make the production economically viable (Manrique et al., 2010). In practice,
the designed hydraulic fractures do not usually result in the expected well performance
due potentially to the fracture cleanup, multi-phase flow, non-Darcy flow, and
penetrating ratio. It has been well-accepted that fracture conductivity and half length are
generally underestimated in the presence of non-Darcy flow (Holditch and Morse, 1976;
Guppy et al., 1982a; b; Vincent et al., 1999; Umnuayponwiwat et al., 2000; Gil et al.,
2003). Few attempts have been made to examine the effects of non-Darcy flow and
penetrating ratio on the performance of horizontal wells with multiple fractures.
Therefore, it is of fundamental and practical importance to accurately quantify non-Darcy
20
effect and penetrating ratios with consideration of the appropriate fracture dimension and
its conductivity.
Either the Forchherimer’s equation or the Barree-Conway model can be used to
examine the effects on the transient pressure behaviour, leading to a partial differential
equation with strong non-linearity, which is difficult to be solved analytically. In general,
steady-state non-Darcy flow is assumed to occur in the fracture, whereas unsteady-state
Darcy flow is assumed in the matrix (Guppy et al., 1982a; b; Umnuayponwiwat et al.,
2000).
After analyzing the transient behaviour of various conductivities with a finite-
difference simulator, Holditch and Morse (1976) concluded that non-Darcy flow in the
fracture reduced the apparent conductivity. Guppy et al. (1982a) proposed a
comprehensive semi-analytical model of non-Darcy flow in wells with finite-conductivity
fractures, assuming that there exists steady-state non-Darcy flow in the fracture and
unsteady-state Darcy flow in the matrix. This facilitates displaying changes in the flux
distribution along the fracture, while non-Darcy flow in a fracture leads to the apparent
fracture conductivity significantly less than its true value. Subsequently,
Umnuayponwiwat et al. (2000) used a similar model to investigate the flux distribution
along the fracture and interaction between the fracture and matrix and found that an
increase in the fracture flow would accelerate the non-Darcy flow effects.
Due to its difference from Darcy’s condition, buildup tests could not be analyzed as
superposition of the drawdown tests for the nonlinearity of a non-Darcy problem (Guppy
et al., 1982b). Although numerical simulation is the primary choice by discretizing both
space and time (Holditch and Morse, 1976; Belhaj et al., 2003; Lai et al., 2012), the
21
semi-analytical method (Guppy et al., 1982a; b; Zeng and Zhao, 2010) has also seen its
extensive applications where only fracture is divided into number of segments and the
solution in each segment can be obtained analytically.
By examining non-Darcy effects in the proppant packs with laboratory tests,
Martins et al. (1990) discovered that pressure loss behaviour occurs at a high flow rate.
Vincent et al. (1999) pointed out that increasing fracture width or placing high
permeability proppant could increase conductivity. Smith et al. (2004) found that non-
Darcy flow should not be simply considered as the reduction of the true conductivity,
while Guppy’s correlations would overestimate the non-Darcy flow effects.
As for non-Darcy effects at a low flow rate, Miskimins et al. (2005) concluded that
non-Darcy effects would reduce the flow capacity by 5-30% in a tight gas reservoir with
relatively low permeability (0.01 mD). By incorporating the unsteady-state solutions both
in the fracture and matrix, Zeng and Zhao (2010) pointed out that such a solution can be
especially applied to the tight formations. The Barree-Conway model has been employed
to describe the pressure transient behaviour of non-Darcy flow in hydraulically fractured
wells with the finite difference method (Al-Otaibi and Wu, 2011).
Few attempts have been made to describe non-Darcy flow in a horizontal well with
multiple fractures. Amini and Valko (2007) incorporated the non-Darcy flow effect
obtained from the volume source function. With consideration of the three-dimensional
fracture geometry, Lin and Zhu (2012) developed a slab source method to evaluate
performance of horizontal wells with or without fractures. The non-Darcy flow is solved
with an iteration method by comparing the difference between apparent permeability and
absolute permeability. However, such a solution is based on the real time domain, making
22
it difficult to incorporate viable flow rates and conductivities usually obtained from the
Laplace domain solution. Also, Wu et al. (2013) adopted numerical simulation to address
non-Darcy effect in an unconventional gas reservoir.
2.4 Summary
Over the past decades, due to its easy computation, the point source function
integrated over a line or a surface has been mostly used to perform the pressure transient
analysis associated with single phase and slightly compressible fluids. Both the
volumetric source function and slab source function have been advanced to include
effects of the source dimension and pressure behaviour inside the sources, though they
are developed in the real time domain. In particular, with consideration of the physical
fracture geometry, the slab source function in the Laplace domain has not been made
available.
Comparing to the real time domain solution, the solution in terms of Laplace
variables can be more easily used to solve the practical problems, particularly those
involving variable rates, skin effect, wellbore storage, and variable conductivities.
Furthermore, it is possible to extend the time range because convolution in the time
domain is reduced to multiplication in the Laplace domain.
Although non-Darcy flow inside a single vertical fracture has been extensively
studied, few attempts have been made to evaluate the performance of a horizontal well
with multiple fractures under non-Darcy effect with the recently proposed Barree-
Conway model. It is of practical and fundamental importance to not only develop a novel
23
slab source function in the Laplace domain, but also evaluate performance of a horizontal
well with multiple fractures in a tight formation under non-Darcy flow effect.
24
CHAPTER 3 DETERMINATION OF FRACTURE
CONDUCTIVITY IN TIGHT
FORMATIONS WITH NON-DARCY FLOW
BEHAVIOUR
Numerous efforts have been made to describe the pressure transient behaviour in
the vertical well with single fracture (Cinco-Ley et al., 1976; Raghavan et al., 1978;
Wattenbarger et al., 1998). Non-Darcy effects inside the fracture have been previously
analyzed based on traditional Forchheimer’s equation (Guppy et al., 1982a; b;
Umnuayponwiwat et al., 2000). In this chapter, non-Darcy effect is incorporated using
the semi-analytical method with newly proposed Barree-Conway model (2004). In this
study, non-Darcy effect is determined by introducing two dimensionless parameters (i.e.,
kmr and FND) based on the Barree-Conway model (Zhang and Yang, 2012a; b; 2013a; b).
Figure 3.1 shows a vertical fracture that is fully penetrated along the well in a
closed box-shaped reservoir. The assumptions are made as follows:
1) The reservoir is assumed to be homogeneous and bounded by upper and lower
impermeable layers. The fluid is considered as slightly compressible, and flow
in the formation is considered as Darcy’s flow, while the non-Darcy flow in the
fracture can be described with the Barree-Conway model (2004).
2) The matrix porosity, m , compressibility, ctm, permeability, km, thickness, h,
reservoir width xe, and length ye are set to be constant. The half length and
width of the vertical fracture is denoted by xf and wf, respectively. The fracture
porosity, f , compressibility, ctf, and permeability, kf are also assumed to be
constant.
25
Figure 3.1 Schematic diagram of a vertical hydraulic fracture in a closed cylindrical
reservoir
h
, ,f t f f
c k
, ,m t m m
c k
fx
z
y
x
h
26
3.1 Theoretical Model
3.1.1 Mathematical formulation
According to the Barree-Conway model (2004), the flow equation in the fracture is
expressed is expressed as follows by dividing kd in the denominator of Equation [2.6],
1
1
mrf mr
p v
x
kk k
v
[3.1]
where is fluid viscosity, v is superficial velocity, is fluid density, mrk is minimum
permeability relative to Darcy permeability, and is the characteristic length.
According to the Darcy’s flow model, the flow equation in the matrix can be
expressed as follows,
m
p v
x k
[3.2]
The fracture is considered as a plane source with non-uniform flux distribution
from the matrix to the fracture, i.e., ,fq x t in 3 /m s m . Based on Equation [3.1], the
equation for fluid flow in the fracture can be written as follows,
f f f f
f tf
f
k p q pc
x x w h t
[3.3]
where
1
1
mrmr
N
f
kk
q
w h
[3.4]
where qN is the flux inside the fracture. The boundary conditions can be written as
follows,
27
02
f f f sc g
x
k hw p Q B
x
[3.5a]
0
f
f
x x
p
x
[3.5b]
As for the pressure drop in the formation, it can be expressed by,
2 2
2 2
mm tm
k p p pc
x y t
[3.6]
with boundary conditions,
0
,mf f f
y
k h pq x x x
y
[3.7a]
, , ip x y t p [3.7b]
The initial condition for both fracture and formation is,
, , 0 ip x y t p [3.7c]
For the convenience of analysis, the following definitions are made to convert the
mathematical models into dimensionless forms,
m i
D
k h p pp
Q
,
m i f
fD
k h p pp
Q
[3.8]
2
mD
m tm f
k tt
c x [3.9a]
D
f
xx
x , D
f
yy
x [3.9b]
sc g
ND
f
Q BF
w h
[3.9c]
28
f f
fD
sc g
q xq
Q B , N
ND
sc g
Q B [3.9d]
f f
fD
m f
k wC
k x [3.9e]
=f m tm
f tf m
k cC
c k
[3.9f]
Equations [3-5b] can then be rewritten as follows,
1fD fD fD
D D fD D
p q p
x x C C t
[3.10]
1
1
mrmr
ND ND
kk
F q
[3.11a]
0
1 1
2D
fD
D fDx
p
x C
[3.11b]
1
0
D
fD
D x
p
x
[3.11c]
Similarly, Equations [6-7b] can be rewritten as follows,
2 2
2 2
D D D
D D D
p p p
x y t
[3.12]
0
, 1 1DfD D
D y
pq x
y
[3.13a]
, , 0D D D Dp x y t [3.13b]
The initial condition can be expressed with dimensionless term,
=0, =0, 0D D D Dp x y t [3.13c]
29
3.1.2 Semi-analytical solution
The semi-analytical method applied to solve the hydraulic fracture system has been
widely discussed in the literature (Guppy et al. 1982a; Umnuayponwiwat et al. 2000;
Zeng and Zhao, 2010). In general, the whole system is divided into matrix system and
fracture system, each of which is solved separately. The fracture system is firstly
discretized into several segments in each of which the flux, qfD, can be approximated to
its average value within the segment. With such an approximation, equations for the
matrix and fracture system can be solved in the Laplace domain in real time, respectively.
Then their solutions are coupled along the fracture interface, leading to a linear system.
Solving the linear system, the flux in each segment can be obtained. Such obtained flux
can be substituted into the first segment to determine the bottomhole pressure in the
Laplace domain in pseudo-time. Finally, the Stehfest inverse algorithm (Stehfest, 1970)
can be employed to convert the bottomhole pressure in the Laplace domain in real time.
Compared to the traditional methods and numerical simulation, the newly developed
technique based on the Laplace domain is not only easily to incorporate the skin factor,
flow rate, wellbore storage, and conductivity in a unified and consistent framework, but
also efficient and accurate in evaluating the petrophysical parameters together with
reservoir performance for a complex reservoir.
Matrix subsystem: The solution to the matrix subsystem can be directly obtained
by applying the point source solution in the Laplace domain to a closed cylindrical
reservoir (Ozkan and Raghavan, 1991), yielding,
21 2
0-1= , -D fD D Dp q x u K u x x y dx
[3.14]
30
where K0 is a zero modified Bessel function of the second type, while it has a singularity
at xD=x. Van Kruysdijk (1988) proposed a method for integration with the singularity.
The modified Bessel function K0(x) can be divided into two parts, -ln(x) and K0(x)+ ln(x).
The singularity in the first part can be integrated analytically.
Fracture subsystem: Because ,D Dx t is a function of both time and space, the
mathematical model for the fracture subsystem is a strong non-linear equation (Equation
[3.15]). To solve such a non-linear equation, the fracture subsystem is firstly discretized
into several segments within each of which the mathematical model can be solved
analytically (see Figure 3.2). Zeng and Zhao (2010) provided a detailed derivation to the
solution in the fracture subsystem.
An average i Dt is employed to simplify the ,D Dx t distribution in each
segment. A pseudo-time is defined based on the average i Dt , i.e.,
0
Dt
Di i d [3.15]
The flux, ,fD D Dq x t , can be approximated to its average value in each fracture
segment i (xDi-1 ≤ xD ≤ xDi),
,fD D D fDi Dq x t q t [3.16]
The mathematical model in segment i (xDi-1 ≤ xD ≤ xDi) is expressed as follows,
2
2
1fD fD
fDi D
D i fD Di
p pq t
x C C
[3.17]
with boundary conditions at xDi-1 and xDi,
31
Figure 3.2 Schematic of discretization of one fracture in the global fracture subsystem
q
Ni x
y
qfDi
qND1
qfD1
qND2
qfD2
…….
…….
qNDi
…….
…….
z
32
11 DiDi
fD ND
D fD xx
p q
x C
,
DiDi
fD ND
D fD xx
p q
x C
[3.18]
The solution to the aforementioned equations can be obtained with the source
function, which can be formulated as follows,
* * *
1 1, , , , ,fDi D i NDi s D Di i NDi s D Di i fDi
fD i
Cp x s q p x x s q p x x s q
C u
[3.19]
where,
1
* * *1= , = , =
D i D i
fDiND NDNDi NDi fDi
ix x
qq qq q q
[3.20]
For no-flow boundary segments, 0 ≤ x'D ≤ ΔxD, with a source at x'D0, van Kruysdijk
(1988) provided the solution:
0
0 0
0
0
2cosh1, , exp
2 exp 2
2coshexp
exp 2
D D i
s D D i D D i
i D i
D D i
D D i
D i
x x s Cp x x s x x s C
u C x s C
x x s Cx x s C
x s C
[3.21]
When the source is located at x'D0 = xDi-1 and x'D0 = xDi, the final solution can be
obtained with superposition principle as follows,
* * *1,
ifD D i i D NDi i D NDi i fDip x s b x q c x q d q [3.22]
where
33
1
1
1 2
2
2cosh1
1
D D i i
D i D i i
D Di i x x s C
i Dx x s C
fD i
x x s Cb x e
C s C e
[3.23a]
1
2
2
2cosh1
1
D i D i
D i D i i
Di D i x x s C
i Dx x s C
fD i
x x s Cc x e
C s C e
[3.23b]
ifD i
Cd
C s
[3.23c]
3.1.3 Continuity conditions
There are two continuity conditions at the interface between any two adjacent
segments in the fracture and boundary between the matrix and the fracture: pressure
continuity and flow rate continuity. Since the solution of the fracture system is based on
the pseudo-time, pressure or flux of any adjacent grids cannot be directly equalized at the
interface in this study. Therefore, a new continuity condition based on the Stehfest
algorithm for the inverse Laplace transformation is proposed as follows. As such, the
solution can be obtained in the Laplace domain, incorporating variable flow rates, skin
effect, wellbore storage, and variable conductivities more easily.
Since the pressure in the real-time domain should be same along the boundary
between the fracture and matrix, we have,
( ) ( )D Di f D Di mp t p t [3.24a]
34
The solution for the fracture system is based on the pseudo-time Laplace
transformation, while the solution for the matrix system is based on the real-time Laplace
transformation. Then Equation [3.24a] can be rewritten as follows,
( ) ( )D i f D Di mp p t [3.24b]
Using the Stehfest algorithm for the inverse Laplace transformation, we have,
1 1
ln 2 ln 2 ln 2 ln 2N N
j jj j
i i D D mf
V p j V p jt t
[3.25]
Accordingly, the pressure continuity condition for the fracture and matrix system
can be obtained as follows,
1 ln 2 1 ln 2=
i i D D mf
p j p jt t
[3.26a]
Similarly, the pressure and flux continuity condition for the node between two
adjacent segments are respectively expressed as follows,
+1 +1
1 ln 2 1 ln 2=
i i i if f
p j p j
[3.26b]
+1 +1
1 ln 2 1 ln 2=
i i i if f
q j q j
[3.26c]
An iterative approach is used here to assume Darcy flow initially occurring in the
fracture, while the non-linear system is transformed to a linear system. The flux at each
node can be re-substituted into the linear system for a new δ. When the flux converges at
each node, the iteration process (see Figure 3.3) terminates to obtain a stable flux
distribution. The linear system can then be solved to obtain the flux from the matrix to the
35
Figure 3.3 Flowchart of solving the non-linear system
qD, PD
Solution of each fracture segment in
the fracture subsystem
Solution of each segment in the
formation subsystem
=0
DAq B
- <new
1
1
mrmr
ND D
kk
F q
,D D newq q
+t t t
YES
Assume non-Darcy Parameter
PPparameter
36
fracture and the flow rate in the fracture at each node. Figure 3.4 presents the format of
coefficient matrix for vertical well with single fracture.
The flux from the matrix to the fracture and the flow rate inside the fracture at each
node are obtained by solving this linear equation system. Substituting the flux at Segment
#1 and flow rate at Node #1 into the original equation for Segment #1 yields the
bottomhole pressure in the Laplace domain in pseudo-time. Subsequently the bottomhole
pressure in the real-time domain can be obtained by using the inverse Laplace algorithm
as proposed by Stehfest (1970).
The solution can also be used for a real gas flow, provided that pseudo-pressure
transformation has been made (Lee and Holditch, 1982; Spivey, 1984). The solution in
terms of pseudo-pressure is defined by,
0
p pm p dp
u p Z p
[3.27]
Since all computations are based on the Laplace transform, wellbore storage can be
easily added with the following well-known identity,
21
wDwD
D wD
pp
u C p
[3.28]
3.2 Model Validation
3.2.1 Forchheimer equation
The newly developed model can be simplified to the Forchheimer equation since it
is the most widely used flow model for describing the non-Darcy flow behavior (Al-
Otaibi and Wu, 2011).
37
Figure 3.4 The coefficient matrix for solving the matrix-hydraulic fracture system in the
single fractured vertical well
38
The common factor between the Barree and Conway model and the Forchheimer
equation is the apparent permeability of non-Darcy flow, which is defined by Equations
[3.29a] and [3.29b], respectively,
1
1
mr
app mr
kk k k
v
[3.29a]
1
app
kk
k v
[3.29b]
where kapp is the apparent permeability, and β is the inertial flow parameter.
When the apparent permeability of two models is set to be the same, the inertial
flow parameter β is solved as follows,
1 mr
mr
k
k k v
[3.30]
where fluid superficial velocity, v, can be approximated using a constant production rate
and cross-sectional area of flow in a well. Equation [3.30] can be used to correlate the
Forchheimer equation and the Barree-Conway model. According to the parameters listed
in Table 3.1 (Vincent et al., 1999; Settari et al., 2000; Gill et al., 2003), the tight gas
reservoir is assumed to be no boundary effects. Figure 3.5 shows an excellent agreement
in the transient stage between the Forchheimer equation simplified from the newly
developed model and the original Barree-Conway model. There is a very minor mismatch
when entering the bilinear period because the flow rate will change significantly at the
initial stage which will then cause a large difference. When reaching the pseudo-radial
flow period, the flow rate will be stabilized and the difference will disappear.
39
Table 3.1 Basic parameters used for simulating pressure-transient response in a tight gas
formation (Vincent et al., 1999; Settari et al., 2000; Gill et al., 2003)
Parameter Value Unit
Reservoir and
Fluid Data
Reservoir Pressure, pi 3000 psi
Reservoir Permeability, km 0.1 mD
Reservoir Porosity, 0.1 fraction
Reservoir Temperature, T 190 oF
Payzone Thickness, h 60 ft
Total Compressibility, ct 1.0×10-5
psi-1
Initial Viscosity, µ 0.018 cP
Density, ρ 0.0625 lbm/ft3
Production Rate, q 10 MMscf/d
Hydraulic
Fracture Data
Fracture Half Length, xf 800 ft
Fracture Width, wf 0.02 ft
Fracture Permeability, kf 180000 mD
Characteristic Length, τ 2.89×104 ft
-1
Relative Minimum Permeability, kmr 0.01 fraction
Equivalent β (Forchheimer) 1.96×105 ft
-1
40
Figure 3.5 Model validation for the Forchheimer equation
41
3.2.2 Numerical simulation
A numerical simulation model is also used for validation. The numerical model is
built by using a reservoir simulator (IMEX, 2010, Computer Modeling Group Ltd.). The
three-dimensional (3D) grid system is 20×20×1 with cell dimension of 20×20×20 ft. The
single cell at the fracture location was locally refined by using the keyword
“Hydraulically Fractured Wells”. Number of refined blocks in each direction is 7×7×1.
Non-Darcy effect was modeled by using the keyword “Non-Darcy Option”.
As for the numerical simulation, non-Darcy flow is described by using the
Geertsma correlation (1974) which is commonly accepted for the unconsolidated
materials,
0.5 5.5
48511=
rg gk k S
[3.31]
The model was built as a tight gas reservoir with porosity of 15% and permeability
of 0.1 mD. Figure 3.6a shows a top view of the 3D grid system, while input parameters
are listed in Table 3.2 (Zhang and Yang, 2013b). As can be seen in Figure 3.6b, there
exists a good agreement between this study and the results from CMG simulation.
3.3 Sensitivity Analysis
Unlike traditional models based on the Forchheimer equation, the non-Darcy effect
is determined by using two dimensionless parameters (i.e., kmr and FND) based on the
Barree-Conway model. Accordingly, effects of these two parameters on pressure
response are to be discussed here since effects of wellbore storage (CD), fracture
42
Table 3.2 Basic parameters used for simulating pressure transient response
Parameter Value Unit
Reservoir and Fluid Data
Reservoir Permeability, km 0.10 mD
Reservoir Porosity, 0.15
Payzone Thickness, h 20 ft
Total Compressibility, ct 9.2×10-5
psi-1
Viscosity, μ 0.026 cP
Density, ρ 0.0612 lbm/ft3
Production Rate, q 0.1 Mscf/d
Initial Reservoir Pressure, pi 5000 psi
Hydraulic Fracture Data
Fracture Half Length, xf 100 ft
Fracture Width, wf 0.02 ft
Fracture Permeability, kf 5000 mD
Equivalent β (Forchheimer) 2.332×107 1/ft
Relative Minimum Permeability, kmr 0.1
Characteristic Length, τ 32.742 1/ft
43
(a)
(b)
Figure 3.6 (a) Top view of the 3D grid system and (b) Model validation between this
study and CMG simulation results
44
conductivity (CfD), and fracture diffusivity (Cη) have been extensively analyzed and
discussed (Cinco-Ley. et al., 1978; Guppy et al., 1982a; Lee and Holditch, 1982).
3.3.1 Relative minimum permeability (kmr)
In the Barree-Conway model, mrk is firstly introduced which is caused by
streamlining or flow heterogeneity. The drawdown type curves for kmr =0.01, 0.10, and
0.50 at FND =100 are depicted in Figure 3.7a. The typical one-fourth slope at early times
of both pressure and its derivative curves are exhibited to show a bilinear flow region for
non-Darcy effect. Then a linear flow with a slope of 0.5 is followed at the end of the
bilinear flow period. Finally, a pseudo-radial flow is attained as the flux in the fracture
has been stabilized. As the value of kmr decreases, the pressure drop and its derivative
curves increase due to strong non-Darcy effect. It is found that non-Darcy effect becomes
significant when kmr becomes less than 0.50. As kmr approaches to 1.00, however, non-
Darcy effect tends to disappear and the pressure response is found to be very similar to
the Darcy’s case.
Figure 3.7b presents the type curves for kmr =0.01, 0.10, and 0.50 at FND =5. When
FND is set to be a smaller value, the pressure and its derivative curves also show a similar
trend to the case at a higher FND value. However, non-Darcy effect becomes less
significant compared with that at a high FND value. This means that FND imposes a
smaller impact on kmr as it is decreased. When FND is set to be a small value, non-Darcy
effect will not affect the pressure response significantly even at a very small kmr value.
45
(a)
(b)
Figure 3.7 Effect of non-Darcy number FND (a) at FND = 100, and (b) at FND = 5
46
3.3.2 Non-Darcy number (FND)
Figures 3.8a and 3.8b present drawdown type curves for FND =1, 10, and 100 at kmr
=0.01 and 0.10, respectively. As shown in Figure 3.8a, the pressure drop and its
derivative curves increase as the non-Darcy number FND increases. This is attributed to
the fact that non-Darcy effect is increased as FND is increased. Obviously, as relative
minimum permeability kmr is decreased, non-Darcy effect becomes much stronger.
Meanwhile, non-Darcy number FND becomes more sensitive than that at a larger kmr. This
is because, as mrk is increased to one, the Barree-Conway model can be converted into
Darcy’s model so that the flow will approach to Darcy flow condition. As can be seen in
Figures 3.7a and 3.8a, the non-Darcy effect will become more evident at a smaller
relative minimum permeability (kmr<0.5) and a larger non-Darcy number (FND>1).
Comparing Figure 3.7b with Figure 3.8b, it can be found that both relative minimum
permeability kmr and non-Darcy number FND can affect the pressure response. However,
non-Darcy number FND that usually results in a large pressure drop at a large kmr is more
sensitive than the relative minimum permeability kmr. Similarly, Figure 3.8 shows that
pressure drop and its derivative curves increase as the non-Darcy number is increased.
3.3.3 Comparison
The relative error caused by Forchheimer equation with respect to the Barree-
Conway model is presented in Figure 3.9. The rate-dependent parameter is examined
from 5 to 100 as kmr is set to be 0.01. It is found that, when FND or DNDq is set as 100, the
relative error can reach to 30.9%, indicating that the Forchheimer equation can
47
(a)
(b)
Figure 3.8 Effect of non-Darcy number FND (a) at kmr = 0.01, and (b) at kmr = 0.10
48
Figure 3.9 Comparison on dimensionless pressure calculated from the Forchheimer
equation and the Barree-Conway model together with the relative errors
49
overestimate the dimensionless pressure by 30.9% compared to the Barree-Conway
model. As FND is decreased, the relative error is decreased along a straight line. When
FND approaches zero, the flow becomes Darcy’s flow with its relative error approaching
to zero. If a threshold value of the relative error is set to be 0.2, the corresponding FND is
found to be 65.
In the non-Darcy flow based on the Forchheimer`s equation, the non-Darcy effect is
determined by dimensionless flow rate ( DNDq ) defined as follows (Guppy et al., 1982a; b;
Umnuayponwiwat et al., 2000),
sc g
DNDf
Q Bq
w h
[3.37]
where Bg is gas formation volume factor, and Qsc is the production rate at field unit. It
should be noted that both dimensionless flow rate and non-Darcy number defined in this
study are dependent on flow rate. When these two rate-dependent parameters are set as
the same value, the only difference between the Forchheimer equation and Barree-
Conway model is the usage of the relative minimum permeability (kmr), which is a
parameter revealing the plateau behaviour at a high flow rate. The physical meaning can
be explained by using the streamline theory (Barree and Conway, 2004).
The relative error caused by Forchheimer equation with respect to the Barree-
Conway model is presented in Figure 3.9. The rate-dependent parameter is examined
from 5 to 100 as kmr is set to be 0.01. It is found that, when FND or DNDq is set as 100, the
relative error can reach to 30.9%, indicating that the Forchheimer equation can
overestimate the dimensionless pressure by 30.9% compared to the Barree-Conway
model. As FND is decreased, the relative error is decreased along a straight line. When
50
FND approaches zero, the flow becomes Darcy’s flow with its relative error approaching
to zero. If a threshold value of the relative error is set to be 0.2, the corresponding FND is
found to be 65.
The relative error caused by Forchheimer equation with respect to the Barree-
Conway model is presented in Figure 3.9. The rate-dependent parameter is examined
from 5 to 100 as kmr is set to be 0.01. It is found that, when FND or DNDq is set as 100, the
relative error can reach to 30.9%, indicating that the Forchheimer equation can
overestimate the dimensionless pressure by 30.9% compared to the Barree-Conway
model. As FND is decreased, the relative error is decreased along a straight line. When
FND approaches zero, the flow becomes Darcy’s flow with its relative error approaching
to zero. If a threshold value of the relative error is set to be 0.2, the corresponding FND is
found to be 65.
3.4 Effect of Non-Darcy Flow
Because of its low production rate in a tight formation, non-Darcy effect on
transient pressure behaviour has not been considered as of yet. To respectively analyze
and discuss the effect of non-Darcy flow on flow performance in a tight oil and gas
formation, a basic data set (Cinco-Ley et al., 1978; Guppy et al., 1982a;
Umnuayponwiwat et al., 2000) used in this study are tabulated in Tables 3.3 and 3.4,
respectively. It is assumed that fracture diffusivity (Cη) and relative minimum
permeability ( mrk ) are to be 105 and 0.01, respectively.
51
Table 3.3 Basic parameters used for simulating pressure-transient response in a tight oil
formation
Parameter Value Unit
Reservoir and Fluid Data
Reservoir Permeability, km 5.00 mD
Reservoir Porosity, 0.18
Payzone Thickness, h 20 ft
Total Compressibility, ct 18×10-6
psi-1
Viscosity, μ 1.8 cP
Density, ρ 60 lbm/ft3
Production Rate, q 195 STB/d
Hydraulic Fracture Data
Fracture Half Length, xf 200 ft
Fracture Width, wf 0.02 ft
Fracture Permeability, kf 10000, 2000 mD
Fracture Conductivity, CfD 100, 20
52
Table 3.4 Basic parameters used for simulating pressure-transient response in a tight gas
formation
Parameter Value Unit
Reservoir and Fluid Data
Reservoir Permeability, km 0.01 mD
Reservoir Porosity, 0.15
Reservoir Temperature, T 710 oR
Payzone Thickness, h 20 ft
Total Compressibility, ct 1.63×10-4
psi-1
Viscosity, μ 0.018 cP
Density, ρ 0.0511 lbm/ft3
Production Rate, q 1 MMscf/d
Hydraulic Fracture Data
Fracture Half Length, xf 200 ft
Fracture Width, wf 0.02 ft
Fracture Permeability, kf 10000, 2000 mD
Fracture Conductivity, CfD 100, 20
53
3.4.1 Tight oil formations
Although the effect of non-Darcy flow on the transient pressure responses of
hydraulically fractured wells has been examined, few attempts have been made in the
tight oil formations at a low production rate. In the tight oil formation example, the
reservoir and fluid data are sourced from Cinco-Ley et al (1978). As for a tight oil
formation with km =5.00 mD, it is assumed that there is a relatively high-conductivity
fracture with CfD =100.0. As shown in Equation [3.9c], non-Darcy number (FND) is a rate-
dependent factor. Therefore, oil production rate is assumed to be constant (195 STB/D)
so that non-Darcy number (FND) is only a function of the characteristic length ( ). Barree
and Conway (2004) suggested that characteristic length ( ) is related to the particle size
or size distribution of the porous media. In this study, the value of characteristic length
( ) is set according to the examples provided by Al-Otabi and Wu (2011). As can be
seen in Figure 3.10, when is increased from 100 to 10000 ft-1
, the value of FND is set to
be 22.001, 2.200 and 0.220, while responses for two Darcy flow scenarios with CfD =47.9
and CfD =100.0 are included.
Comparing the response between non-Darcy flow and Darcy flow (CfD =100.0),
non-Darcy flow is found to induce an additional pressure drop. As characteristic length
( ) is decreased, non-Darcy number (FND) is increased, leading to a strong non-Darcy
flow effect. As observed by Guppy et al. (1982a) and Umnuayponwiwat et al. (2000), the
additional pressure drop due to non-Darcy effect can also be expressed by a reduction in
the apparent conductivity of the fracture. In Figure 3.10, the Darcy’s scenario of CfD
=47.9 can be matched with the non-Darcy scenario of CfD =100.0 and FND =2.200 all the
time. The traditional analysis method can result in more than 50% error in the estimation
54
Figure 3.10 Type curves for non-Darcy effect in a tight oil formation at CfD = 100.0
55
of conductivity. This is the reason why the type curves that can be matched with the
conventional Darcy’s model would underestimate fracture conductivity if the non-Darcy
effect exists (Guppy et al., 1982; Umnuayponwiwat et al., 2000). Therefore, the fracture
half-length together with other fracture parameters cannot be accurately determined if the
apparent fracture conductivity is evaluated by using the conventional method.
To better understand the non-Darcy effect, Figure 3.11 presents the flux distribution
from the matrix to the fracture as a function of time at FND =22.001. In this case with
strong non-Darcy effect, it is found that the fluid enters from the heel of the fracture at
the very beginning, resulting in a large pressure drop until the pseudo-radial flow is
established. As time proceeds, the flux decreases at the heel of the fracture but increases
at its toe. This is ascribed to the fact that strong non-Darcy effect causes resistance in the
fracture, forcing the fluids to largely enter from the heel at the beginning of well
production. When pseudo-radial flow is established, the flux distribution stabilizes and
remains unchanged. Since the resistance force becomes smaller, most of the fluids enter
the fracture at its toe, causing a smaller pressure drop. It should be noted that the
additional pressure drop caused by non-Darcy effect is rate-dependent and that the flux
distribution along the fracture is a function of time until the pseudo-radial flow is initiated.
To perform further illustration, flux distribution inside the fracture is plotted in
Figure 3.12. At the beginning of well production, the flux inside the fracture generally
decreases at each node, though it is decreased sharply in the half of the fracture close to
the wellbore. This is because most of fluids entering the wellbore from the formation to
the fracture occur at its toe.
56
Figure 3.11 Flux distribution from the matrix to the fracture in a tight oil formation at
CfD = 100 and FND =22.001.
57
Figure 3.12 Flux distribution inside the fracture in a tight oil formation at CfD = 100 and
FND =22.001
58
For the purpose of comparison, a relatively low-conductivity fracture is considered
with CfD =20.0 in the same formation by changing the fracture permeability to a smaller
value. As depicted in Figure 3.13, non-Darcy number (FND) is still the same as that in a
high-conductivity fracture. The transient pressure and its derivative curves show a similar
trend to those in a high-conductivity fracture except that a larger pressure drop can be
obtained at the early stages. This is ascribed to the fact that a low fracture conductivity
can also cause an additional pressure drop which is similar to that of the non-Darcy effect.
Figure 3.14 presents flux distribution along the fracture with a low conductivity. As
shown in Figure 3.14, the flux at the early times is larger than that in the high-
conductivity fracture at the same location, directly leading to a larger pressure drop. In
the late stage, the flux distribution is similar to that of a high conductivity scenario,
indicating that the fluid entering the fracture becomes less at its heel but more at its toe.
In practice, bilinear flow analysis proposed by Cinco-Ley and Samaniego-V (1981)
is widely used to estimate the fracture conductivity. It is worthwhile, however, to
examine how non-Darcy behaviour will affect bilinear flow behaviour
(Umnuayponwiwat et al., 2000). As shown in Figure 3.15a, the pressure change is
increased following a straight line as an increase in the fourth of time at a low
conductivity. This is because bilinear flow exists at the beginning of the production. At
the same fourth of time, the pressure change is reduced as characteristic length increases.
This means that non-Darcy flow leads to an increase in the pseudo-pressure drop.
Similarly, Figure 3.15b shows the same trend for a scenario with a higher conductivity.
Obviously, there exists non-Darcy flow behaviour in a tight oil formation even at a low
production rate.
59
Figure 3.13 Type curves for non-Darcy effect in a tight oil formation at CfD = 20.0
60
Figure 3.14 Flux distribution from the matrix to the fracture in a tight oil formation at
CfD = 20.0 and FND =22.001
61
(a)
(b)
Figure 3.15 Bilinear flow analysis (a) at CfD = 20.0, and (b) at CfD = 100.0
62
3.4.2 Tight gas formations
The non-Darcy effect has been widely discussed and analyzed in the gas formations
(Martins et al., 1990; Vincent et al., 1999; Smith et al., 2004). The gas production rate is
set to be constant (1 MMscf). In the tight gas formation, the value of FND is set to be
121.328, 24.266 and 12.133 as τ is increased from 1000 to 10000 ft-1
, while responses for
two Darcy flow scenarios with CfD =9.6 and CfD =100.0 are included.
Figure 3.16 presents the type curves for non-Darcy effect in a tight gas formation
with high fracture conductivity. As can be seen, there is a large additional pseudo-
pressure drop at the early stages. Comparing the curve of FND =121.328 with Darcy’s
condition, it is found the pressure drop is larger than that of the tight oil formation. This
is because the non-Darcy number (FND) can be set to be a larger value for a higher gas
production rate. It is also found that the Darcy’s scenario of CfD =9.6 can be matched with
the non-Darcy scenario of CfD =100.0 and FND =24.266. Comparing to the case in tight oil
formation, the traditional method will cause a larger error in the estimation of
conductivity because non-Darcy effect is usually larger in the tight gas formation. Figure
3.17 shows the flux distribution from the matrix to the fracture at a high fracture
conductivity. As shown in Figure 3.17, the trend is very similar to that in the tight oil
formation; however, there is more fluid entering into fracture from the matrix, finally
resulting in a larger pseudo-pressure drop.
Figure 3.18 shows the type curves for non-Darcy effect in a tight gas formation
with a low fracture conductivity. Compared with high-conductivity fracture scenario, the
bilinear flow is more significant than that in a high conductivity fracture mainly because
of low conductivity other than the non-Darcy effect. Figure 3.19 presents the flux
63
Figure 3.16 Type curves for non-Darcy effect in a tight gas formation at CfD = 100.0
64
Figure 3.17 Flux distribution from the matrix to the fracture in a tight gas formation at
CfD = 100.0 and FND =121.328
65
Figure 3.18 Type curves for non-Darcy effect in a tight gas formation at CfD = 20.0
66
Figure 3.19 Flux distribution from the matrix to the fracture in a tight gas formation at
CfD = 20.0 and FND =121.328
67
3.5 Case Study
The case study is a drawdown test on an oil well which was first reported by Cinco
et al. (1978). Figure 20 shows the type-curves match between the field data on the oil
well in a tight formation and the solution of the semi-analytical model in this study. Two
cases of Darcy and non-Darcy flow are considered to examine the non-Darcy effect on oil
wells. As shown in Figure 20, there exists an excellent agreement between the field
measurements and solutions of the proposed model in this study for both Darcy and non-
Darcy flow cases. As for the Darcy’s case, the dimensionless fracture conductivity CfD is
calculated to be 6.267, which is very close to the original result of 2π. One of the matches
for the non-Darcy case corresponds to CfD =6.274, FND =0.47, kmr =0.12. This result is
consistent with the previous analysis that the non-Darcy effect in a tight oil formation is
usually very small. It should be noted that it is possible to obtain multiple combinations
of Darcy and non-Darcy parameters by adjusting some parameters. Therefore, it is
recommended that at least two flow tests be required to accurately determine the fracture
conductivity, relative minimum permeability and non-Darcy number.
3.6 Summary
The pressure transient behaviour has been analyzed in a vertical well with single
fracture. Five flow regimes in a finite conductivity fracture can be identified with the
point source function. Firstly a bilinear appears at the initial production followed by the
formation linear flow, elliptical flow, pseudo-radial flow, and eventually ended with
boundary dominated flow. Based on Barree-Conway model, Non-Darcy flow effect
68
Figure 3.20 Type curve match for the field data on an oil well in a tight formation
69
inside the fracture is dominated by relative minimum permeability (kmr) and non-Darcy
number (FND). It is found that non-Darcy number (FND) is more sensitive than relative
minimum permeability (kmr). The non-Darcy effect with high non-Darcy number (FND) is
significant even at a small relative minimum permeability (kmr). Both non-Darcy effect in
tight gas formations and tight oil formations are illustrated in this chapter. The results
show that non-Darcy effect is more significant in tight gas formations than that in tight oil
formations.
70
CHAPTER 4 SLAB SOURCE FUNCTION FOR
EVALUATING PERFORMANCE OF A
HORIZONTAL WELL WITH MULTIPLE
FRACUTRES
The pressure transient behaviour is much more complex in a horizontal well with
multiple fractures compared to that of a vertical well with single fracture. In this chapter,
a novel slab source function is firstly developed in the Laplace domain in a box-shaped
reservoir with a closed boundary. When solving the horizontal well and multiple fractures
system in the semi-analytical method, more fracture segments are involved by using the
superposition principle, leading to a large and complex linear system. Effects of fracture
stages, fracture dimension, and fracture conductivity are firstly examined and discussed,
followed by partially penetrating effect. Finally, non-Darcy flow effect is extended from
the single fracture to the horizontal well with multiple fractures based on the Barree-
Conway model.
In this study, a horizontal well with multi-stage fractures is considered in a box-
shaped reservoir (see Figure 4.1). The assumptions are made as follows:
1) The matrix is homogeneous;
2) The formation has rectangular shape with no flow outer boundaries;
3) The horizontal wellbore is parallel to the reservoir boundary;
4) The transverse hydraulic fractures have a finite conductivity;
5) The vertical fractures partially penetrate the formation;
6) The multiple transverse fractures are assumed to be identical;
71
Figure 4.1 Schematic diagram of a horizontal well with multi-stage fractures in a box-
shaped reservoir
72
7) Non-Darcy flow is assumed to be in the hydraulic fractures, while Darcy`s
flow happened in the matrix;
8) The formation fluid can only enter the wellbore through the fractures at the
open ports in the liner or through perforated intervals, as the case may be; and
9) The model is derived for single-phase oil and gas flow, while pseudo-pressure
and time transformations could be used for gas flow.
4.1 Mathematical Formulation
The source and Green’s function has been applied to describe fluid flow in porous
media for decades. Instantaneous Green’s functions in both real time domain and Laplace
domain have been provided to include geometries of the source and different boundary
conditions (Gringarten and Ramey, 1973; Ozkan and Raghavan, 1991). The advantages
of solutions in terms of the Laplace variable have been widely accepted to solve problems
associated with variable rates, wellbore storage, skin effects and conductivity. A problem
arises when applying the Newman’s product principle in the Laplace domain, i.e.,
1 2, , = , ,f x y t f x t f y t [4.1a]
1 2 1 2, , = , , , ,f x y t f x t f y t f x t f y t L L L L [4.1b]
It can be noted that the solution to a 2D problem, , ,f x y t , can be expressed by a
product form of two 1D solutions (i.e., 1 ,f x t and 2 ,f y t ) in the real time domain but
not applicable in the Laplace domain. Chen and Raghavan (1991) proposed the following
method to extend the following product principle to the Laplace domain.
73
4.1.1 Product principle
As noted by LePage (1980), the Laplace transform of the product of two functions
can be written as follows,
[4.2]
where Br is the Bromwich path to the right of all singular points of f1(p). Chen (1990)
shows that if 1f s has only simple poles, the integral of Equation [4.2] is reduced to
1 2 2n nn
f t f t R s f s s L [4.3]
where nR s is the residue of 1f s at pole sn. In particular, if 1f s is of the fractional
form of h s g s with simple poles, sn, arising solely from the zeros of g s and
0nh s , then the residue of sn in Equation [4.3] can be simplified as .
Then, Equation [4.3] can be rewritten as follows,
[4.4]
The first term on the right side of Equation [4.4] accounts for the possibility that
sn=0 (s0) is a pole. The basic instantaneous source functions and the values of
n nh s g s for instantaneous plane sources in infinite slab reservoirs are listed in
Tables 4.1 and 4.2, respectively (Chen et al., 1991).
1 2 1 2
1=
2 Br
f t f t f p f s p dpi
L
n nh s g s
0
1 2 2 21
0
n
nn
n
h s h sf t f t f s f s s
g s g s
L
74
4.1.2 Slab source function
The slab source functions in an infinite reservoir can be obtained by simply
multiplying the corresponding infinite plane source functions in Table 4.1 by a term of
source length as defined as follows (Chen, 1990),
2
,f x
f w f w f
x
sh x sF x s x x x x x
s
, [4.5]
where xw is assumed at the source center with half fracture length xf. The poles and
residues of the slab sources can be obtained by multiplying the corresponding entries in
Table 4.2 by a term defined as follows,
, 2 0f n fF x s x n , [4.6a]
2sin
, 1f n x
f n
n x
x sF x s n
s
, [4.6b]
A slab source in a closed rectangular reservoir can be written by multiplying three
1D instantaneous source functions in x-, y- and z- direction (see Figure 4.2), respectively.
, , , , , , , , , , , , , , , , , ,w w w f f f w f w f w fS x y z x y z x y z t VII x x x t VII y y y t VII z z z t
[4.7]
where
, , ,w fVII x x x t is the slab source (prescribed flux) in x- direction
, , ,w fVII y y y t is the slab source (prescribed flux) in y- direction
, , ,w fVII z z z t is the slab source (prescribed flux) in z- direction
75
Table 4.1 Basic instantaneous source functions in an infinite slab reservoir (Chen et al.,
1991)
x=0 xw x
e Source Type Function Number
Instantaneous Source Functions For x>xw
(interchange x and xw for x<x
w)
Prescribed
Flux
VII(x)
Prescribed
Pressure
VIII(x)
Mixed
Boundaries
IX(x)
cosh cosh
sinh
w x e x
x x e x
x s x x s
s x s
sinh sinh
sinh
w x e x
x x e x
x s x x s
s x s
cosh sinh
cosh
w x e x
x x e x
x s x x s
s x s
76
Table 4.2 Values of h(sn)/g'(sn) and (sn, n=0,1,...) for instantaneous plane sources in an
infinite slab reservoir (Chen et al., 1991)
x=0 xw
xe Source Type
Function
Number
h(sn)/g'(sn) sn n=1, 2, ... n=0 n=1, 2, …
Prescribed
Flux
VII(x)
Prescribed
Pressure
VIII(x)
Mixed
Boundaries
IX(x)
1
ex
2cos cosw
e e e
n nx x
x x x
2
x
e
n
x
02
sin sinwe e e
n nx x
x x x
0 -0.5 -0.52
cos coswe e e
n nx x
x x x
2
-0.5x
e
n
x
2
x
e
n
x
77
Figure 4.2 Schematic of a slab source model
xe
ye
ze
xf
yf
zf
x
z y
78
The pressure drop induced by the source at (xw, yw, zw) can be expressed by (Zhang
et al., 2013):
1
1
1
, , ,
1, , , , , , , , ,
8
, , ,2
2 cos cos , , , ,
2 cos cos , , , ,
4
w w w f f f
t f f f
p w f
t e e f
n f e w w f np nn
e e
m f e w w f mp mm
e e
n f en
P x y z s
q sS x y z x y z x y z s
c x y z
q sS y y y s
c x z y
n nF x x x x S y y y s
x x
m mF z z z z S y y y s
z z
F x x
1
cos cos
cos cos , , , , ,
w
e e
m f e w w f n mp nmm
e e
n nx x
x x
m mF z z z z S y y y s
z z
[4.8]
where
2
, , ,f w e
p w f
e
sh y s ch y s ch y y sS y y y s
s sh y s
[4.9a]
2, , , ,
f n w n e n
w f np n
n e n
sh y s ch y s ch y y sS y y y s
s sh y s
[4.9b]
2, , , ,
f m w m e m
w f mp m
m e m
sh y s ch y s ch y y sS y y y s
s sh y s
[4.9c]
79
2, , , , ,
f n m w n m
w f n mp nm
n m
e n m
e n m
sh y s ch y sS y y y s
s
ch y y s
sh y s
[4.9d]
sin=
f e
n f e
f e
n x xF x x
n x x
[4.9e]
sin=
f e
m f e
f e
m z zF z z
m z z
[4.9f]
2
n en x [4.9g]
2
m em z [4.9h]
The detailed derivation in Equation [4.8] is presented in Appendix, while the
computation problem is avoided by Ozkan and Raghavan (1991). The slab source
function is used to solve the horizontal well with multiple fractures instead of point
source function (Equation [3.14]).
4.2 Linear System
With the similar semi-analytical method presented in Chapter 3, As for each
discretized segment, uniform flux solution of the slab source function in Equation [4.8] is
80
used to describe fluid flow in the matrix. Flow in the fracture is considered as 1D flow
model using Equation [3.22], assuming that pressure drop is evenly distributed in the
horizontal wellbore. Therefore, these two types of flow are then coupled by using the
equations provided below. The fracture number in the reservoir is set as N, each of which
is divided into M segments. Segment #1 represents the heel of the fracture, while
Segment #m represents the toe. Single fracture is considered when N = 1, while multiple
fractures are assumed when N > 1.
Assuming that no flow enters the toe of the fracture, the model contains 4N×M
unknowns:
1) Pressure at matrix nodes: PD1,1, PD1,2, …, PD1,M; PD2,1, PD2,2, …, PD2,M; …; PDN,1,
PDN,2, …, PDN,M;
2) Pressure at fracture nodes: PfD1,1, PfD1,2, …, PfD1,M; PfD2,1, PfD2,2, …, PfD2,M; …;
PfDN,1, PfDN,2, …, PfDN,M;
3) Flux from matrix to fracture nodes: qfD1,1, qfD1,2, …, qfD1,M; qfD2,1, qfD2,2, …,
qfD2,M; …; qfDN,1, qfDN,2, …, qfDN,M; and
4) Flux in the fracture node: qND1,1, qND1,2, …, qND1,M ; qND2,1, qND2,2, …, qND2,M; …;
qNDN,1, qNDN,2, …, qNDN,M.
4.2.1 Constraint equations
Two constraint conditions are usually used for pressure transient analysis. As for
fixed production and bottomhole pressure control, we respectively have:
max,1
1
=N
NDii
s
[4.10]
81
and
,min
1,1
wf
ND
pp
s [4.11]
where Qmax is the maximum flow rate and pwf, min is the minimum bottomhole pressure.
One equation is obtained from the constraint equation. Because the solution is developed
in the Laplace domain, the constraints can be changed at any time without superposition
in time.
4.2.2 Flow equations
By the superposition principle, the pressure drop and flux at each source location as
a result of each segment produces at a constant rate is written as follows,
,
, , , , , ,, , , m n
Di j Dm n Dm n Dm n fDi j i jp x y z t q F [4.12]
where ,
,
m n
i jF is the coefficient of single source solution of Segment #j in Fracture #i
relative to Segment #m in Fracture #n. For the entire fracture, a set of linear equations can
be obtained as follows,
1,1 1,1 1,1
1,1 1,1 1,2 1,2 , , 1,1
1,2 1,2 1,2
1,1 1,1 1,2 1,2 , , 1,2
, , ,
1,1 1,1 1,2 1,2 , , ,
+ ...
+ ...
+ ...
fD fD fDN M N M D
fD fD fDN M N M D
N M N M N M
fD fD fDN M N M DN M
q F q F q F P
q F q F q F P
q F q F q F P
[4.13]
A total of N×M equations can be obtained.
With the solution in the fracture subsystem, another set of linear equations are
written in the first fracture as follows,
82
1 1,1 1 1,2 1 1,1 1,1
2 1,2 2 1,3 2 1,2 1,2
1, 1 1, 1,M 1,
+c
+c
+c
ND ND fD fD
ND ND fD fD
M ND M M ND M M fD fD M
b q q d q P
b q q d q P
b q q d q P
[4.14]
As there are N fractures, there will be a number of N×M equations.
4.2.3 Continuity equations
As discussed in Chapter 3, the solution for the matrix subsystem is based on the
real-time Laplace transformation, while the solution for the fracture subsystem is resulted
from the pseudo-time Laplace transformation.
The pressure continuity condition for the fracture and matrix subsystems can be
obtained as follows,
, ,
1 ln 2 1 ln 2=fD D
i j i j D D
p j p jt t
[4.15a]
where τi,j is the pseudo-time at segment i of fracture j. Thus, N×M equations can be
obtained for the N fractures.
Similarly, the pressure continuity condition for the node between any two adjacent
segments is expressed as follows,
, , +1, +1,
1 ln 2 1 ln 2=fD fD
i j i j i j i j
p j p j
[4.15b]
N fractures have N × (M-1) interfaces, so there will be N × (M-1) equations.
83
4.2.4 Wellbore equations
Because no pressure drop is assumed in the horizontal wellbore, frictional,
acceleration and radial inflow effects are not considered in this study. The pressure along
the wellbore should be the same, we have,
1,1 2,1 ,1...fD fD fDNp p p [4.16]
A total of N-1 equations can be written for interfaces between wellbore and
fractures. Therefore, 4N×M equations can be obtained, corresponding to the same number
unknown variables. With the similar iterative method used in Chapter 3 for non-Darcy
flow, a matrix different from single fracture case is shown in Figure 4.3.
4.3 Model Validation
Numerical simulation models were used for validation. The numerical models were
built by using a reservoir simulator (IMEX, 2010, Computer Modelling Group Ltd.). The
global grid system is 27×27×5, and the cell dimensions are 20×20×10 ft. The single cell
at the fracture location was locally refined by using the keyword “Hydraulically
Fractured Wells”. Number of refined blocks in each direction is 5×5×3. Figures 4.4a and
b show a top view and cross-section of the global grid system. Three fractures are evenly
distributed in a horizontal well, where only the perforations in the fractures are open to
make the fluid flow from the fracture to the wellbore. The basic input parameters are
listed in Table 4.3 (Vincent et al., 1999; Gil et al., 2003).
84
Table 4.3 Basic parameters used for simulating pressure transient response
Parameter Value Unit
Reservoir and Fluid
Data
Reservoir Pressure, pi 3000 psia
Reservoir Temperature, T 190 ºF
Matrix Permeability, km 0.1 mD
Reservoir Porosity, 0.1 fraction
Payzone Thickness, h 50 ft
Initial Gas Viscosity, μi 0.018 cP
Total Compressibility, ct 6.15×10-5
psi-1
Gas Density, ρ 8.23 lbm/ft3
Gas Molecular Weight, M 17.382 lbm/lb-mol
Production Rate, q 1.0 MMscf/d
Hydraulic Fracture
Data
Fracture Half Length, xf 200 ft
Fracture Width, wf 0.02083 ft
Fracture Permeability, kf 50000 mD
85
Figure 4.3 The coefficient matrix for solving the matrix-hydraulic fracture system
1 2 3 … M-2 M-1 M
1
2
3
M-2
M-1
M
*
* * *
… …* * *
* * *
* * *
* *
…
……
*
** *
* *
* *
* *
* *
……
* *
1 2 3 … M-2 M-1 M … 1 2 3 … M-2 M-1 M … 1 2 3 … M-2 M-1 M …
1
2
3
M-2
M-1
M
……
* *
* * *
…* * *
* * *
* * *
…
* *
1
2
3
M-2
M-1
M
1
2
3
M-2
M-1
M
……
** *
* *
* *
* *
* *
……
……
* *
* *
* *…
…
* *
* *
*
* *
* *
* *…
…
* *
* *
*
* * * * * * * * * * * **… …
* * * * * * * * * * * *** * * * * * * * * * * **
* * * * * * * * * * * *** * * * * * * * * * * **
* * * * * * * * * * * **
* * * * * * * * * * * **
* * * * * * * * * * * **
* * * * * * * * * * * **
* * * * * * * * * * * *** * * * * * * * * * * **
* * * * * * * * * * * **
……
……
… …
… …
… …… …
… …
… …
… …
… …
… …
… …
… …
1 2 3 … M-2 M-1 M
1
2
3
M-2
M-1
M
*
* * *
… …* * *
* * *
* * *
* *
…
……
*
** *
* *
* *
* *
* *
……
* *
1 2 3 … M-2 M-1 M … 1 2 3 … M-2 M-1 M … 1 2 3 … M-2 M-1 M …
1
2
3
M-2
M-1
M
……
* *
* * *
…* * *
* * *
* * *
…
* *
1
2
3
M-2
M-1
M
1
2
3
M-2
M-1
M
……
** *
* *
* *
* *
* *
……
……
* *
* *
* *…
…
* *
* *
*
* *
* *
* *…
…
* *
* *
*
* * * * * * * * * * * **… …
* * * * * * * * * * * *** * * * * * * * * * * **
* * * * * * * * * * * *** * * * * * * * * * * **
* * * * * * * * * * * **
* * * * * * * * * * * **
* * * * * * * * * * * **
* * * * * * * * * * * **
* * * * * * * * * * * *** * * * * * * * * * * **
* * * * * * * * * * * **
……
……
… …
… …
… …… …
… …
… …
… …
… …
… …
… …
… …
86
(a)
(b)
Figure 4.4 (a) Top view of the 3D grid system and (b) Cross-section of the 3D grid
system
87
As for the numerical simulation, non-Darcy flow is described by using the
Geertsma correlation (1974) which is commonly accepted for the unconsolidated
materials. Inertial factor β is calculated to be 6.86×107 ft
-1. The common factor between
the Barree-Conway model and the Forchheimer equation is the apparent permeability of
non-Darcy flow, which is defined by Equations [3.37a] and [3.37b], respectively. When
kmr is set to be 5×10-9
, τ is calculated to be 2.133×10-3
ft. As can be seen in Figure 4.5,
there exists an excellent agreement between this work and the CMG simulation result,
showing that the slab source method produces reliable transient pressure results.
The newly slab source function is also validated with widely used point source
function. In the slab source function, the width of fracture is incorporated in a single
vertical fracture case. Figure 4.6 presents the comparison result between the point source
and slab source function. It is found that minor difference exists in the initial production
because the fracture width is very small. However, the development of slab source
function is still meaningful for easy computation, which is not only applicable in the
single vertical fracture, but in the horizontal fracture, multiple fractures and horizontal
well.
4.4 Results and Discussion
4.4.1 Fracture stages
Figure 4.7 presents the pressure response and its derivative curves under different
fracture stages with the same fracture length for each stage. Six flow regimes can be
observed in a multiple-fracture system.
88
Figure 4.5 Model validation between this study and CMG simulation results
89
Figure 4.6 Comparison between this study and CMG simulation results
90
Figure 4.7 Effect of fracture stages on the well response with the same fracture length
91
Firstly, a bilinear/linear flow appears at the initial production followed by the early-
radial flow, compound-linear flow, elliptical flow, pseudo-radial flow, and eventually
ended with boundary flow. As can be seen, the pressure drop decreases as the fracture
stage number is increased. This is due to the fact that more stages lead to a larger fracture
volume and a smaller fracture spacing as well. This results in a longer bilinear/linear flow,
though number of fracture stages is less. As the number of fracture stages increases the
interference among these hydraulic fractures becomes more evident, especially between
the dimensionless time of 0.3-20×10-3
.
In a tight oil or shale gas reservoir, the permeability is often found to be in the
micro-Darcy to nano-Darcy range, so it will take a long time (i.e., measured in decades)
to reach the pseudo-steady state flow (Ozkan et al., 2009). In Figure 4.7, the slope of both
pressure and derivative curves is approaching unity when tD = 2.0×10-3
in the case of 40
fracture stages. This means that the pressure and its derivative curve bend towards to the
pseudo-steady flow. This phenomenon can be explained by the occurrence of the
stimulated reservoir volume (SRV) (Mayerhofer et al., 2010). The fractured well can
only produce from the volume trapped between fractures.
4.4.2 Fracture conductivity
Figure 4.8 presents drawdown type curves for fracture conductivity CfD = 1, 10, 30
and 50 with five pairs of fractures. Fracture conductivity is found to mainly influence
early-stage bilinear/linear flow regime. As fracture conductivity CfD is increased, the
pressure drop and its derivative value become smaller. When fracture conductivity is set
to be large enough, the linear flow regime is followed by the bilinear flow regime.
92
Figure 4.8 Pressure response together with its derivative for five pairs of fractures under
various fracture conductivities
93
To better understand the conductivity effect, Figure 4.9a shows the flux distribution
at the initial production tD = 10-6
when fracture conductivity increased from 1 to 50. The
flux at the heel of the fracture is increased as the conductivity is decreased. Figure 4.9b
illustrates the flux distribution at tD = 102, which allows the flux distribution to be
stabilized. As can be seen in Figure 4.9b, at a small fracture conductivity CfD = 1, there
are still much fluid entering from the heel of the fracture, while, at large conductivity CfD
= 50, most fluid enters the toe of the fracture. This is ascribed to the fact that a smaller
fracture conductivity induces a larger resistance in the fracture, forcing the fluids to enter
the portions of the matrix progressively distant from the fracture heel with time, and
ultimately culminates in production entering the fracture from its toe. When pseudo-
radial flow is established, the flux distribution stabilizes and remains unchanged. Since
the resistance force becomes smaller, most of the fluids enter the fracture at its toe,
resulting in a smaller pressure drop.
4.4.3 Fracture length
Figure 4.10 illustrates effect of fracture length at four pairs of fractures. All the
fractures with different length firstly show bilinear/linear pressure drop followed by a
gradual change that leads to an elliptical flow regime with a slope that is larger than half
but less than 1. As can be seen, the pressure drop increases as the fracture length is
increased, while the linear flow regime is gradually changed to the bilinear regime. It is
found that the longer the fracture is, the longer the duration of the elliptical flow regime
will be.
94
(a)
(b)
Figure 4.9 Effect of fracture conductivity on the flow distribution at (a) tD = 1.0E-6, and
(b) tD = 1.0E2
95
Figure 4.10 Effect of fracture length on the well response at four pairs of fractures
96
4.4.4 Fracture spacing
Different from single fracture, fracturing spacing existing in multiple fractures has
significant effect in the pressure transient behaviour. Figure 4.11 presents the effect of
fracture spacing at four pairs of fractures. The boundaries are set to be constant, and the
horizontal wellbore is assumed to place in the same location. The only varying parameter
is fracture spacing which is illustrated as dimensionless form. As shown in Figure 4.11,
the fracture spacing significantly influences the intermediate radial flow regime. It is
found that the intermediate radial flow regime cannot be observed when fracture spacing
is set as a small value (DD = 3). As fracture spacing increased, the intermediate flow
regime becomes more evident at larger value (DD = 8).
As can be seen, when boundary conditions are kept unchanged, the fracture spacing
also influences the pseudo-radial flow regime. At a large value (DD = 8), the pseudo-
radial flow regime almost disappears. This can be explained that larger fracturing spacing
makes the fracture more approaching to the boundary, which means the pseudo-steady
state flow directly occurs after the elliptical flow regime.
4.4.5 Penetrating ratio
Although numerous efforts have been made to study pressure transient behaviour of
hydraulic fractured wells, there are few studies pertaining to effects of the partially
penetrating fractures (Raghavan et al., 1978; Rodriguez et al., 1984; Alpheous and Tiab,
2008). Typically, it is preferred that the fracture height be equal to the formation
thickness, where fully-penetrating fractures are produced. However, a fully penetrating
97
Figure 4.11 Effect of fracture spacing on the well response at four pairs of fractures
98
fracture may lead to an early water breakthrough in a reservoir with bottom water, or
unanticipated water production in a reservoir with an incompetent top or bottom seal that
has an adjacent permeable water-bearing formation.
Figure 4.12a depicts drawdown type curves of three vertical fractures at fracture
conductivity CfD = 10 when penetrating ratio α = 0.6, 0.7, 0.8, 0.9 and 1.0. Penetrating
ratio α = 0.5 can be used as the threshold value to classify the pressure response (see
Figure 4.12b). The pressure behaviour tends to be similar to that of the fully penetrating
fractures when other factors such as fracture stages, spacing and dimensions remain
unchanged. The first linear flow regime appears at the initial production followed by a
short transition regime.
Figure 4.12b plots the drawdown type curves of three vertical fractures at fracture
conductivity CfD = 10 when penetrating ratio α = 0.1, 0.2, 0.3, 0.4, and 0.5. It is observed
that the pressure drop becomes larger as the penetrating ratio is decreased. The first linear
flow regime becomes shorter as the penetrating ratio is decreased. Meanwhile, an early
radial flow regime instead of the transition regime occurs.
4.4.6 Non-Darcy effect
The non-Darcy effect in the single fracture has been discussed in Chapter 3. It has
been noted that the non-Darcy effect is dominated by both relative minimum permeability
(kmr) and non-Darcy number (FND).
99
(a)
(b)
Figure 4.12 Effect of partially penetrating ratio of three stages at CfD=10 and (a) α>0.5,
and (b) α≤0.5
100
Table 4.4 presents the basic parameters used in the experiments by Lai et al. (2012).
The flow rate ranges from 707.2 Sm3/d to 283168.2 Sm
3/d, covering the most possible
field production rates. Since the non-Darcy number FND is calculated to be 2.7-1091.4
with Equation [16b], it is set to be 1, 10, 100 and 1000 to cover the most possible
scenarios from low to high flow rates.
Figure 4.13a depicts drawdown type curves for FND = 1, 10, 100 and 1000 at kmr =
0.01 with four pairs of fractures, respectively. The trend is very similar to that in the
single fracture. As FND is increased, the pressure drop and its derivative curves increase
due to strong non-Darcy effect. It is found that non-Darcy effect becomes significant
when FND becomes larger than 10. As FND approaches to zero, however, non-Darcy effect
tends to disappear and the pressure response is found to be very similar to that of the
Darcy’s case.
Figure 4.13b plots drawdown type curves for FND = 1, 10, 100 and 1000 at kmr =
0.10, respectively. The pressure drop together with its derivative is becoming much
smaller at kmr = 0.10 than that at kmr = 0.01. Comparing to the larger kmr case, there still
exists a difference in pressure drop even in the pseudo-radial flow regime at the smaller
kmr = 0.01. Figures 4.14a and b show drawdown type curves for kmr = 0.01, 0.05 and 0.10
at FND = 1000 and FND = 10, respectively. As shown in Figure 4.14a, the pressure drop
and its derivative curves increase when kmr is decreased. However, as shown in Figure
4.14b, the pressure drop and its derivative curves are almost the same when kmr is
decreased. The non-Darcy effect becomes insignificant at a smaller non-Darcy number
(FND = 10) when kmr is decreased.
101
Table 4.4 Parameters used for describing non-Darcy flow with Barree-Conway model in
multiple fractures (Lai et al., 2012)
Parameter Value Unit
Darcy permeability, kd 10.0 Darcy
Minimum permeability, kmin 0.1, 0.5, 1.0 Darcy
Minimum relative Permeability, kmr 0.01, 0.05, 0.10, fraction
Viscosity, μ 1 cP
Density, ρ 62.43 lbm/ft3
Characteristic length, τ 3000-30000 1/ft
102
(a)
(b)
Figure 4.13 Effect of non-Darcy number FND (a) at kmr = 0.01, and (b) at kmr = 0.10
103
(a)
(b)
Figure 4.14 Effect of non-Darcy number kmr at (a) FND = 1000, and (b) FND = 10
104
As can be seen in Figures 4.13 and 4.14, the non-Darcy flow behaviour in multiple
fractures is similar as that of single fracture. Non-Darcy effect will become more evident
at a smaller relative minimum permeability (kmr<0.05) and a larger non-Darcy number
(FND>10). In addition, the non-Darcy number (FND) is more sensitive than the relative
minimum permeability (kmr), resulting in a larger pressure drop even at a larger kmr. The
major difference is that non-Darcy flow can cause a larger pressure drop in the single
fracture than that in the multiple fractures. This is ascribed to the fact that the fixed
production rate is assumed to be unity in all cases, causing the flux in each fracture is
smaller than that of single fracture. Then, a smaller flux can result in a smaller non-Darcy
number (FND), and eventually lead to smaller pressure drop.
To better understand the non-Darcy effect, Figure 4.15a presents the flux
distribution at the initial production tD = 10-6
. As shown in Figure 4.15a, most fluids enter
from the heel of the fracture at the initial production. Non-Darcy effect forces more fluid
entering from the heel of the fracture than that of Darcy flow.
Figure 4.15b illustrates the flux distribution from the matrix to the fracture at tD =
103, which allows the flux distribution to be stabilized. As can be seen in Figure 4.15b, as
for Darcy flow, most of the flow occurs at the toe of the fracture. However, as for non-
Darcy flow, the flux from the heel increases, whereas the flux from the toe decreases with
an increase in FND and a decrease in kmr. At kmr = 0.01 and FND = 1000, the flux at the
heel of the fracture is even larger than that at its toe. This is attributed to the fact that non-
Darcy flow increases the flow resistance in the fracture, forcing more fluid to enter the
fracture from the area close to the wellbore. This is also the reason why the effective
105
(a)
(b)
Figure 4.15 Effect of non-Darcy flow on the flow distribution at (a) tD = 1.0E-6, and (b)
tD = 1.0E3
106
fracture length will be shorter than its original design due to the non-Darcy flow in the
fracture.
4.5 Case Study
The Bakken formation is located in the Williston Basin covering parts of Montana,
North Dakota, and South Saskatchewan. A tremendous hydrocarbon is discovered in this
formation and production increases rapidly with technology advancement in horizontal
drilling and massively fracturing. This formation is composed of three distinct geological
layers: Upper shale, Middle Bakken and Lower shale. The Middle Bakken is a low
porosity and low permeability reservoir composed of mixed clastic and carbonate
sediments primarily deposited in a shallow marine environment (Luo et al., 2010).
Figure 4.16 presents the pressure buildup test and production history from a well in
the Bakken formation of South Saskatchewan. As shown in Figure 4.16, the top part
shows the pressure data reported form an automated acoustic well sounder equipment,
while the bottom part illustrates the well production history used in the analysis of the
pressure data. The well was hydraulically fractured with 15 stages and then commenced
its production on December 20, 2010. The well was shut in for a buildup test on January
27, 2011 and terminated on February 28, 2011 after 769.5 hours of buildup time.
The reservoir and fracture properties are listed in Table 4.5. It has been noted that
non-Darcy flow during the producing period also affects the buildup test response
(Umnuayponwiwat et al., 2000). The pressure data was well matched by using the newly
formulated model with single phase and multiple transverse fractures (see Figure 4.17). It
is shown from the derivative curve that there exists a wellbore storage effects after the
107
Table 4.5 Reservoir and fracture properties for the well in the Bakken formation
Parameter Value Unit
Payzone Thickness, h 5.9 ft
Reservoir Porosity, 0.10 fraction
Specific Gravity 0.81 fraction
Viscosity, μ 0.797 cP
Reservoir Temperature, T 176 ºF
Bottomhole pressure, pw 498.19-2249.97 psi
Wellbore Radius, rw 0.23 ft
Well Length, L 3564 ft
Number of Fractures 15
108
Figure 4.16 Pressure buildup test and production history
109
Figure 4.17 Flow regime interpretation for the pressure buildup response
110
first 1.5 hours. Due to the wellbore storage, the bilinear flow and the early radial flow
cannot be observed. Then a linear flow regime with half slope develops, defining the
formation of the linear flow regime. This is followed by a short elliptical flow which is
not obviously. Eventually, the pseudo-radial flow with constant derivative value is found
in the late stage.
Figure 4.18 presents the measured and simulated pressure buildup data, while the
matching parameters are tabulated in Table 4.6. Due to wellbore storage effect, the
penetrating ratio cannot be determined in the pressure response. Therefore, the fracture
height is assumed to be equal to the formation thickness as the net payzone is only 5.9 ft
thick. Because two new parameters are introduced in this study, it is difficult to obtain the
unique match result by type curve matching. If non-Darcy flow is not considered in the
match, the dimensionless conductivity (CfD) was found to be 20.76. When non-Darcy
effect is incorporated, one of the matches corresponds to the type curve for CfD = 23.52,
kmr = 0.087 and FND = 8.32. The other match is with type curve for CfD = 23.52, kmr =
0.524 and FND = 73.55. Due to the fact that production of this well is not high (83.98
STB/d), the first case of CfD = 23.52, kmr = 0.087 and FND = 8.32 is considered as the
most reasonable matching result. Then the characteristic length (τ) is calculated to be
241.12 1/ft. There exists an excellent agreement between the measured and simulated
pressure for the buildup test as well.
111
Table 4.6 Type curve matching results for the buildup test
Parameter Value Unit
Wellbore Storage, C 0.12 bbl/psi
Skin Factor, s 0.21
Fracture Half Length, xf 195 ft
Fracture Height, hf 5.9 ft
Fracture Conductivity, Cf 5642 mD·ft
Matrix Permeability, km 0.872 mD
Relative Minimum Permeability, kmr 0.087 fraction
Characteristic Length, τ 241.12 ft-1
112
Figure 4.18 Type curve matching of pressure buildup data
113
4.6 Summary
As for a horizontal well with multiple fractures, it is found that the interference
becomes more evident as fracture stages increase. The longer the fracture is, the longer
the duration of the elliptical flow regime will be. Fracture conductivity is found to mainly
affect the early-stage bilinear/linear flow regime. Two types of pressure response can be
classified based on the threshold penetrating ratio α = 0.5. In the case of a large
penetrating ratio, the pressure response is similar to that of the fully penetrating case.
When penetrating ratio is smaller than 0.5, the first linear flow regime occurs followed by
an early radial flow regime. At the same fixed production rate, non-Darcy effect in the
single fractured vertical well can cause a larger pressure drop than that of the horizontal
well with multiple fractures under the same conditions.
114
CHAPTER 5 CONCLUSIONS AND RECOMMENDATIONS
5.1 Conclusions
In this study, the point source function was firstly applied in the single vertical
fracture well by developing a semi-analytical method to solve the single fracture problem
with consideration of the finite conductivity and non-Darcy effect in the fracture. In the
semi-analytical method, equations for the matrix and fracture subsystems can be solved in
the Laplace domain with source functions, respectively. Then, their solutions are coupled
along the fracture interface, leading to a linear system. Solving the linear system, the flux
in each segment can be obtained, which is substituted into the first segment to determine
the bottomhole pressure in the Laplace domain. Finally, the Stephest inverse algorithm
can be employed to convert the solutions in the Laplace domain to that in the real time
domain. The non-Darcy flow effect inside the fracture can be solved by converting the
real time to the pseudo-time. Continuity conditions are modified based on the pseudo-
time, and the solutions under non-Darcy flow effect can be obtained by iterative methods.
Due to the difficulty for evaluating performance of horizontal wells with multiple
fractures, a novel slab source function was then developed to describe the fluid flow in
the porous media. The slab source function attributes geometry to sources and considers
the pressure effect inside sources by using the superposition principle over multiple
sources. Flow effect inside fractures can be examined by dividing the fracture into several
segments, each of which can be treated as a slab source. Such a newly developed
technique has been validated with numerical simulation method, and then applied to
115
describe the pressure transient behaviour under various fracture conductivities, fracture
half-lengths and fracture in a field case.
The major conclusions that can be drawn from this thesis study are summarized as
follows:
1) Five flow regimes can be observed in a finite conductivity fracture with the
point source function. More specifically, a bilinear appears at the initial
production followed by the formation linear flow, elliptical flow, pseudo-radial
flow, and eventually ended with boundary dominated flow. The slab source
function in the Laplace domain is developed successfully to describe pressure
transient behaviour in a complex reservoir and well system;
2) The non-Darcy flow effect inside the hydraulic fractures is examined based on
the Barree-Conway model. Comparing to traditional Forchheimer’s equation,
non-Darcy flow effect is dominated by relative minimum permeability (kmr)
and non-Darcy number (FND). Non-Darcy number (FND) is more sensitive than
relative minimum permeability (kmr). The non-Darcy effect with high non-
Darcy number (FND) is significant even at a small relative minimum
permeability (kmr);
3) At lower non-Darcy number (FND), the results are almost the same between
Forchheimer’s equation and Barree-Conway model. At a higher non-Darcy
number (FND), the Forchheimer’s equation can overestimate pressure drop by
30.9% compared to the Barree-Conway model;
4) Non-Darcy effect in a tight gas reservoir is found to be more significant than
that in a tight oil reservoir. At the same fixed production rate, non-Darcy effect
116
in a vertical well with single fracture results in a higher pressure drop than that
in a horizontal well with multiple fractures;
5) Fracture conductivity mainly affects the early-stage bilinear/linear flow regime.
A smaller fracture conductivity causes a larger resistance in the fracture,
forcing the fluids to largely enter the toe at the beginning of production;
6) As the number of the fracture stages increases, the interference among those
hydraulic fractures becomes more evident, especially between the
dimensionless times of 0.3×10-3
and 20.0×10-3
; and
7) Two types of pressure response can be classified based on the threshold
penetrating ratio α = 0.5. In the case of a large penetrating ratio, the pressure
response is similar to that of the fully penetrating case. When penetrating ratio
is smaller than 0.5, the first linear flow regime occurs followed by an early
radial flow regime.
5.2 Recommendations
Based on this thesis study, the following recommendations for future studies are
made:
1) The slab source function can be extended to describe fluid flow in more
complex cases by incorporating natural fractures, horizontal wellbore
contribution, and stimulated reservoir volume (SRV);
2) Experiments should be conducted to quantify the ranges of minimum
permeability plateau for different proppant and fracturing fluids;
117
3) Non-Darcy effect based on the Barree-Conway model should be examined on
more field cases, especially on fractured gas wells in tight gas and/or shale gas
reservoirs; and
4) A comprehensive two-phase flow model should be developed to evaluate well
performance under non-Darcy flow inside the hydraulic fractures.
118
REFERENCES
Al-Kobaisi, M., Ozkan, E., and Kazemi, H., 2006. A Hybrid Numerical/Analytical Model
of a Finite-Conductivity Vertical Fracture Intercepted by a Horizontal Well. SPE
Reserv. Eval. Eng. 9 (4): 345-355.
Al-Otaibi, A.M. and Wu, Y.S., 2011. An Alternative Approach to Modeling Non-Darcy
Flow for Pressure Transient Analysis in Porous and Fractured Reservoirs. Paper
SPE 149123, presented at the SPE/DGS Saudi Arabia Section Technical
Symposium and Exhibition, Al-Khobar, Saudi Arabia, May 15-18.
Al-Rbeawi, S. and Tiab, D., 2012. Effect of Penetrating Ratio on Pressure Behavior of
Horizontal Wells with Multi-Inclined Hydraulic Fractures. Paper SPE 153788,
presented at the SPE Western Regional Meeting, Bakersfield, CA, March 21-23.
Amini, S., Ilk, D., and Blasingame, T.A., 2007. Evaluation of the Elliptical Flow Period
for Hydraulically Fractured Wells in Tight Gas Sands – Theoretical Aspects and
Practical Considerations. Paper SPE 106308, presented at the SPE Hydraulic
Fracturing Technology Conference, College Station, TX, January 29-31.
Amini, S. and Valko, P.P., 2010. Using Distributed Volumetric Sources to Predict
Production From Multiple-Fractured Horizontal Wells Under Non-Darcy-Flow
Conditions. SPE J. 15 (1): 105-115.
Andrade, Jr., J.S., Almeida, M.P., Medes Filho, J., Havlin, S., Suki, B., and Stanley, H.E.,
1997. Fluid Flow through Porous Media: The Role of Stagnant Zones. Phys. Rev.
Lett. 79 (20): 3901-3904.
119
Badu, D.K. and Odeh, A.S., 1988. Productivity of a Horizontal Well Appendices A and B.
Paper SPE 18334, presented at the SPE Annual Technical Conference and
Exhibition, Houston, TX, October 2-5.
Bahrami, H. and Siavoshi, J., 2013. Interpretation of Reservoir Flow Regimes and
Analysis of Well Test Data in Hydraulically Fractured Unconventional Oil and
Gas Reservoirs. Paper SPE 164033, presented at the SPE Middle East
Unconventional Gas Conference and Exhibition, Muscat, Sultanate of Oman,
January 28-30.
Balhaj, H.A., Agha, K.R., Butt, S.D., and Islam, M.R., 2003. Simulation of Non-Darcy
Flow in Porous Media Including Viscous, Inertial and Frictional Effects. Paper
SPE 84879, presented at the SPE International Improved Oil Recovery
Conference in Asia Pacific, Kuala Lumpur, October 20-21.
Barak, A.Z., Comments on ‘High Velocity Flow in Porous Media’ by Hassanizadeh and
Gray. Transp. Porous Media, 2 (6): 533-535.
Barree, R.D. and Conway, M.W., 2004. Beyond Beta Factors: A Complete Model for
Darcy, Forchheimer and Trans-Forchheimer Flow in Porous Media. Paper SPE
89325, presented at the SPE Annual Technical Conference and Exhibition,
Houston, TX, September 26-29.
Bello, R.O., and Wattenbarger, R.A., 2010. Multi-stage Hydraulically Fractured Shale
Gas Rate Transient Analysis. Paper SPE 126754, presented at the SPE North
Africa Technical Conference and Exhibition, Cairo, Egypt, February 14-17.
Brown, M., Ozkan, E., Raghavan, R., and Kazemi, H., 2009. Practical Solutions for
Pressure Transient Response of Fractured Horizontal Wells in Unconventional
120
Reservoirs. Paper SPE 125043, presented at the SPE Annual Technical
Conference and Exhibition, New Orleans, LA, October 4-7.
Chen, H.Y., Poston, S.W., and Raghavan, R., 1991. An Application of the Product
Solution Principle for Instantaneous Source and Green’s Functions. SPE Form.
Eval. 6 (2): 161-167.
Cinco-Ley, H., Samaniego-V, F., and Domínguez A, N., 1978. Transient Pressure
Behavior for a Well with a Finite-Conductivity Vertical Fracture. SPE J. 18 (4):
253-264.
Cinco-Ley, H. and Samaniego-V, F., 1981. Transient Pressure Analysis for Fractured
Wells. J. Pet. Technol. 33 (9): 1749-1766.
Cinco-Ley, H. and Meng, H.Z., 1988. Pressure Transient Analysis of Wells With Finite
Conductivity Vertical Fractures in Double Porosity Reservoirs. Paper SPE 18172,
presented at the SPE Annual Technical Conference and Exhibition, Houston, TX,
October 2-5.
Cipolla, C.L., Lolon, and Dzubin, B., 2009. Evaluating Stimulation Effectiveness in
Unconventional Gas Reservoirs. Paper SPE 124843, presented at the SPE Annual
Technical Conference and Exhibition, New Orleans, LA, October 4-7.
Darcy, H.P.G., 1856. The Public Fountains of the City of Dijon (Appendix). Bookseller of
the Imperial Corps of Bridges, Highways and Mines, Quay of Augustins.
Fetkovich, M.J., 1980. Decline Curve Analysis Using Type Curves. J. Pet. Technol. 32
(6): 1065-1077.
Firoozabadi, A. and Katz, D.L., 1979. An Analysis of High-Velocity Gas Flow Through
Porous Media. J. Pet. Technol. 31 (2): 211-266.
121
Forchheimer, P.F., 1901. Wasserbewegung durch Boden. Zeitschrift des Vereines
deutscher Ingenieure. 45 (5): 1781-1788.
Frederick, D.C. and Graves, R.M., 1994. New Correlations to Predict Non-Darcy Flow
Coefficients at Immobile and Mobile Water Saturation. Paper SPE 28451,
presented at the SPE Annual Technical Conference and Exhibition, New Orleans,
LA, September 25-28.
Gill, J.A., Ozkan, E., and Raghavan, R., 2003. Fractured-Well-Test Design and Analysis
in the Presence of Non-Darcy Flow. SPE Reservoir Eval. Eng. 6 (3): 185-196.
Geertsma, J., 1974. Estimating the Coefficient of Inertial Resistance in Fluid Flow
through Porous Media. SPE J. 14 (5): 445-450.
Gringarten, A.C., Ramey, H.J., and Raghavan, R., 1973. The Use of Source and Green’s
Functions in Solving Unsteady-Flow Problems in Reservoirs. SPE J. 13 (5): 285-
296.
Gringarten, A.C., Ramey, H.J., and Raghavan, R., 1974. Unsteady-State Pressure
Distributions Created by a Well with a Single Infinite Conductivity Vertical
Fracture. SPE J. 14 (4): 347-360.
Guo, G.L., Evans, R.D., and Chang, M.M., 1994. Pressure-Transient Behavior for a
Horizontal Well Intersecting Multiple Random Discrete Fractures. Paper SPE
28390, presented at the SPE Annual Technical Conference and Exhibition, New
Orleans, LA, September 25-28.
Guppy, K.H., Cinco-Ley, H., Ramey, Jr., H.J., and Samaniego-V, F., 1982a. Non-Darcy
Flow in Wells with Finite-Conductivity Vertical Fractures. SPE J. 22 (5): 681-698.
122
Guppy, K.H., Cinco-Ley, H. and Ramey, Jr., H.J., 1982b. Pressure Buildup Analysis of
Fractured Wells Producing at High Flow Rates. J. Pet. Technol. 34 (11): 2655-
2666.
Hill, R.J., Koch, D.L., and Ladd, A.J.C., 2001. Moderate Reynolds Number Flows in
Ordered and Random Arrays of Spheres. J. Fluid Mech. 448: 243-278.
Holditch, S.A. and Morse, R.A., 1976. The Effects of Non-Darcy Flow on the Behavior if
Hydraulically Fractured Gas Wells. J. Pet. Technol. 28 (10): 1169-1179.
Horne, R.N. and Temeng, K.O., 1995. Relative Productivities and Pressure Transient
Modeling of Horizontal Wells with Multiple Fractures. Paper SPE 29891,
presented at the SPE Middle East Oil Show, Bahrain, March 11-14.
Ilk, D., Rushing, J.A., and Blasingame, T.A., 2009. Decline Curve Analysis for HP/HT
Gas Wells: Theory and Applications. Paper SPE 125031, presented at the SPE
Annual Technical Conference and Exhibition, New Orleans, LA, October 04-07.
Ilk, D., 2010. Well Performance Analysis for Low to Ultro-low Permeability Reservoir
System. Ph.D. Dissertation, Texas A&M University, College Station, TX.
Jones, S.C., 1972. A Rapid Accurate Unsteady-State Klinkenberg Permeameter. SPE J.
12 (5): 383-397.
Kuchuk, F.J. and Habusky, T.M., 1984. Pressure Behavior of Horizontal Wells with
Multiple Fractures. Paper SPE 27971, presented at the University of Tulsa
Centennial Petroleum Engineering Symposium, Tulsa, OK, August 29-31.
Lai, B.T., 2010. Experimental Measurement and Numerical Modeling of High Velocity
Non-Darcy Flow Effects in Porous Media. Ph.D. Dissertation, Colorado School of
Mines, Golden, Colorado.
123
Lai, B.T., Miskimins, J.L., and Wu, Y.S., 2012. Non-Darcy Porous Media Flow
According to the Barree and Conway Model: Laboratory and Numerical
Modeling Studies. SPE J. 17 (1): 70-79.
Larsen, L. and Hegre, T.M., 1994. Pressure Transient Analysis of Multifractured
Horizontal Wells. Paper SPE 28389, presented at the SPE Annual Technical
Conference and Exhibition, New Orleans, LA, September 25-28.
LePage, W.R, 1980. Complex Variables and the Laplace Transform for Engineers. Dover
Publications Inc., New York City, 336-352.
Li, D.C. and Engler, T.W., 2001. Literature Review on Correlations of the Non-Darcy
Coefficient. Paper SPE 70015, presented at the SPE Permian Basin Oil and Gas
Recovery Conference, Midland, TX, May 15-16.
Lin, J. and Zhu, D., 2012. Predicting Well Performance in Complex Fracture Systems by
Slab Source Method. Paper SPE 151960, presented at the SPE Hydraulic
Fracturing Technology Conference, Woodlands, TX, February 6-8.
Luo S.Q., Neal, L., Arulampalam, P., and Ciosek, J.M., 2010. Flow Regime Analysis of
Multi-stage Hydraulically-Fractured Horizontal Wells with Reciprocal Rate
Derivative Function: Bakken Case Study. Paper SPE 137514, presented at the
SPE Canadian Unconventional Resources and International Petroleum Conference,
Calgary, AB, October 19-21.
Manrique, M., Thomas, C., Ravikiran, R., Izadi, M., Lantz, M., Romero, J., and Alvarado,
V., 2010. EOR: Current Status and Opportunities. Paper SPE 130113, presented at
the SPE Improved Oil Recovery Symposium, Tulsa, OK, April 24-28.
124
Martins, J.P., Milton-Tayler, D., and Leung, H.K., 1990. The Effects of Non-Darcy Flow
in Propped Hydraulic Fractures. Paper SPE 20709, presented at the SPE Annual
Technical Conference and Exhibition, New Orleans, LA, September 23-26.
Medeiros, F., Ozkan, E., and Kazemi, H., 2006. A Semi-Analytical, Pressure Transient
Model for Horizontal and Multilateral Wells in Composite, Layered, and
Compartmentalized Reservoirs. Paper SPE 102834, presented at the SPE Annual
Technical Conference and Exhibition, San Antonio, TX, September 24-27.
Meyer, B.R., Bazan, L.W., Jacot, R.H., and Lattibeaudiere, M.G., 2010. Optimization of
Multiple Transverse Hydraulic Fractures in Horizontal Wellbores. Paper SPE
131732, presented at the SPE Unconventional Gas Conference, Pittsburgh, PA.,
February 23-25.
Miksimins, J.L., Lopez-Hernandez, H.D., and Barree, R.D., 2005. Non-Darcy Flow in
Hydraulic Fractures: Does It Really Matter? Paper SPE 96389, presented at the
SPE Annual Technical Conference and Exhibition, Dallas, TX, October 9-12.
Narayanaswamy, G., Sharma, M.M., and Pope, G.A., 1999. Effect of Heterogeneity on
the Non-Darcy Flow Coefficient. SPE Reservoir Eval. Eng. 2 (3): 296-302.
Newman, A.B., 1936. Heating and Cooling Rectangular and Cylindrical Solids. Ind. Eng.
Chem. 28 (5), 545-548.
Ogunsanya, B.O., Oetama, J.F., Lea, J.F., Heinze, L.R., and Adisoemarta, P.S., 2005. A
Physically Consistent Model for Describing Transient Pressure Behaviour of
Horizontal Drainholes. Paper 2005-071, presented at the Canadian International
Petroleum Conference, Calgary, AB, June 7-9.
125
Ozkan, E. and Raghavan, R., 1991. New Solutions for Well-Test-Analysis Problems: Part
1-Analytical Considerations. SPE Form. Eval. 6 (3): 359-368.
Ozkan, E. and Raghavan, R., 1991. New Solutions for Well-Test-Analysis Problems: Part
2-Computational Considerations. SPE Form. Eval. 6 (3): 369-378.
Ozkan, E., Brown, M., Raghavan, R., and Kazemi, H., 2009. Comparison of Fractured
Horizontal-Well Performance in Conventional and Unconventional Reservoirs.
Paper SPE 121290, presented at the SPE Western Regional Meeting, San Jose,
CA, March 24-26.
Raghavan, R.S., Uraiet, A., and Thomas, G., 1978. Vertical Fracture Height: Effect on
Transient Flow Behavior. SPE J. 18 (4): 265-277.
Raghavan, R.S., Chen C.C., and Agarwal, B., 1994. An Analysis of Horizontal Wells
Intercepted by Multiple Fractures. SPE J. 2 (3): 235-245.
Rodriguez, F, Horne, R., and Cinco-Ley, H., 1984. Partially Penetrating Fractures:
Pressure Transient Analysis of an Infinite Conductivity Fracture. Paper SPE
13057, presented at the SPE Annual Technical Conference and Exhibition,
Houston, TX, September 16-19.
Ruth, D. and Ma, H., 1992. On the Derivation of the Forchheimer Equation by Means of
the Average Theorem. Transp. Porous Media, 7 (3): 255-264.
Smith, M.B., Bale, A., Britt, L.K., Cunningham, L.E., Jones, J.R., Klein, H.H., and Wiley,
R.P., 2004. An Investigation of Non-Darcy Flow Effects on Hydraulic Fractured
Oil and Gas Well Performance. Paper SPE 90864, presented at the SPE Annual
Technical Conference and Exhibition, Houston, TX, September 26-29.
126
Stanley, H.E., and Andrade, Jr., J.S., 2001. Physics of the Cigarette Filter: Fluid Flow
through Structures with Randomly-Placed Obstacles. Physica A. 295 (1-2): 17-30.
Stehfest, H., 1970. Algorithm 368: Numerical Inversion of Laplace Transforms [D5].
Commun. ACM. 13 (1): 47-49.
Thompson, J.K., 1981. Use of Constant Pressure, Finite Capacity Type Curves for
Performance Prediction of Fractured Wells in Low Permeability Reservoirs. Paper
SPE 9839, presented at the Low Permeability Reservoir Symposium, Denver, CO,
May 27-29.
Tiab, D., 1989. Direct Type-Curve Synthesis of Pressure Transient Tests. Paper SPE
18992, presented at the Low Permeability Reservoir Symposium, Denver, CO,
March 6-8.
Tiab, D., 1993. Analysis of Pressure and Pressure Derivative without Type-Curve
Matching - III. Vertically Fractured Wells in Closed Systems. Paper SPE 26138,
presented at the SPE Western Regional Meeting, Anchorage, AL, May 26-28.
Umnuayponwiwat, S., Ozkan, E., and Pearson, C.M., 2000. Effect of Non-Darcy Flow on
the Interpretation of Transient Pressure Response of Hydraulically Fractured
Wells. Paper SPE 63176, presented at the SPE Annual Technical Conference and
Exhibition, Dallas, TX, October 1-4.
Valko, P.P. and Amini, S., 2007. The Method of Distributed Volumetric Sources for
Calculating the Transient and Pseudosteady-State Productivity of Complex Well-
Fracture Configuration. Paper SPE 106279, presented at the SPE Hydraulic
Fracturing Technology Conference, College Station, TX, January 29-31.
127
van Kruysdijk, C.P.J.W., 1988. Semianalytical Modeling of Pressure Transients in
Fractured Reservoirs. Paper SPE 18169, presented at the SPE Annual Technical
Conference and Exhibition, Houston, TX, October 2-5.
van Kruysdijk, C.P.J.W. and Dullaert, G.M., 1989. A Boundary Element Solution of the
Transient Pressure Response of Multiple Fractured Horizontal Wells. Paper
presented at the 2nd
European Conference on the Mathematics of Oil Recovery,
Cambridge, England.
Vincent, M.C., Pearson, C.M., and Kullman, J., 1999. Non-Darcy and Multiphase Flow
in Propped Fractures: Case Studies Illustrate the Dramatic Effect on Well
Productivity. Paper SPE 54630, presented at the SPE Western Regional Meeting,
Anchorage, AL, May 26-28.
Wan, J. and Aziz, K., 2002. Semi-analytical Well Model of Horizontal Wells with
Multiple Hydraulic Fractures. SPE J. 7 (4): 437-445.
Wattenbarger, R.A., El-Banbi, A.H., Villegas, M.E, and Maggard, J.B., 1998. Production
Analysis of Linear Flow into Fractured Tight Gas Wells. Paper SPE 39931,
presented at the SPE Rocky Mountain Regional/Low-Permeability Reservoirs
Symposium and Exhibition, Denver, CO, April 5-8.
Whitaker, S., 1996. The Forchheimer Equation: A Theoretical Development. Transp.
Porous Media, 25 (1): 27-61.
Wood, J.M., 2012. Water Distribution in the Montney Tight Gas Play of the Western
Canadian Sedimentary Basin: Significance for Resource Evaluation. Paper SPE
161824, presented at the SPE Canadian Unconventional Resources Conference,
Calgary, AB, October 30-November 1.
128
Wright, C.A., Davis, E.J., Weijers, L., Golich, G.M., Ward, J.F., Demetrius, S.L., and
Minner, W.A., 1998. Downhole Tiltmeter Fracture Mapping: A New Tool for
Directly Measuring Hydraulic Fracture Dimensions. Paper SPE 49193, presented
at the SPE Annual Technical Conference and Exhibition, New Orleans, LA,
September 27-30.
Wu, Y.S., Li, J.F., Ding, D., Wang, C., and Di, Y., 2013. A Generalized Framework
Model for Simulation of Gas Production in Unconventional Gas Reservoir. Paper
SPE 163609, presented at the SPE Reservoir Simulation Symposium, Woodlands,
TX, February 18-20.
Zhang, F. and Yang, D., 2013a. Determination of Fracture Conductivity in Tight
Formations with Non-Darcy Flow Behaviour. SPE J., available on-line.
Zhang, F. and Yang, D., 2013b, Effects of Non-Darcy Flow and Penetrating Ratio on
Performance of Horizontal Wells with Multiple Fractures. Paper SPE 167218, to
be presented at the SPE Canadian Unconventional Resources Conference, Calgary,
AB, November 5-7. Submitted to SPE J. for possible publication (Manuscript No.:
SJ-0819-0010) on August 7, 2013.
Zhang, F. and Yang, D., 2012a. Determination of Fracture Conductivity in Tight
Formations with Non-Darcy Flow Behaviour. Paper SPE 162548, presented at the
SPE Canadian Unconventional Resources Conference, Calgary, AB, October 30-
November 1.
Zhang, F. and Yang, D., 2012b. Determination of Minimum Permeability Plateau and
Characteristic Length in Porous Media with Non-Darcy Flow Behaviour
129
(Manuscript No.: PETROL4598). Submitted to J. Pet. Sci. Eng. for possible
publication on November 29.
Zhang, F., Yang, D., and Styles, J.A., 2013. A Novel Slab Source Function for Evaluating
Performance of a Horizontal Well with Multiple Fractures (Manuscript No.: SJ-
0713-0005). Submitted to SPE J. for possible publication on July 3.
Zeng, F. and Zhao, G., 2010. The Optimal Hydraulic Fracture Geometry under Non-
Darcy Flow Effects. J. Pet. Sci. Eng. 72 (1-2), 143-157.
Zerzar, A. and Bettam, Y., 2003. Interpretation of Multiple Hydraulically Fractured
Horizontal Wells in Closed Systems. Paper SPE 84888, presented at the SPE
International Improved Oil Recovery Conference in Asia Pacific, Kuala Lumpur,
Malaysia, October 20-21.
Zhu, D., Magalhaes, F.V., and Valko, P.P., 2007. Predicting the Productivity of Multiple-
Fractured Horizontal Gas Wells. Paper SPE 106280, presented at the SPE
Hydraulic Fracturing Technology Conference, College Station, TX, January 29-31.
130
APPENDIX: DERIVATION OF THE SLAB SOURCE SOLUTION
IN THE LAPLACE DOMAIN
Newman’s product solution method is firstly used by Gringarten and Ramey (1973)
in the application of source and Green’s functions for multi-dimensional flow through
porous media. This method, however, is only applicable in the real (spatial and temporal)
domain. For the development of solution in the Laplace domain, Chen et al. (1991)
proposed a method to extend the product principle to the Laplace domain. The detailed
derivation of this method can be found elsewhere (Chen et al., 1991). In this study, the
slab source function is developed by following the same procedure.
A slab can be obtained by considering the intersection of a slab source in a linear
reservoir in the x- and y- directions and a slab source in a linear reservoir in the z-
direction. The required instantaneous source function can be written as follows,
, , , , , , , , , , , , , , , , , ,w w w f f f w f w f w fS x y z x y z x y z t VII x x x t VII y y y t VII z z z t
[4.7]
where
, , ,w fVII x x x t is the slab source (prescribed flux) in x- direction
, , ,w fVII y y y t is the slab source (prescribed flux) in y- direction
, , ,w fVII z z z t is the slab source (prescribed flux) in z- direction
Equation 4.7 can be solved in two steps:
, , , , , , , , , , , ,f w w f f w f w fS x y x y x y t VII x x x t VII y y y t [A-1]
131
, , , , , , , , , , , , , , , , , ,w w w f f f f w w f f w fS x y z x y z x y z t S x y x y x y t VII z z z t [A-2]
Taking the Laplace transform of Equation [A-2], its product source solution can be
expressed as follows,
1
, , ,, , , , , , , , , , , , , , ,
, , ,
, , ,, , , , , ,
, , ,
w f o
w w w f f f f w w f f
w f oVII
w f m
f w w f f mm
w f mVII
h z z z sS x y z x y z x y z s S x y x y x y s
g z z z s
h z z z sS x y x y x y s s
g z z z s
[A-3]
Equation [A-3] can be written as follows,
1
, , , , , , , , ,
2, , , , , ,
2 cos cos , , , , , , , ,
w w w f f f
f
f w w f f
e
n f e w w w f f n mf nmm
e e
S x y z x y z x y z s
zS x y x y x y s
z
n nF z z z z S x y x y x y s
z z
[A-4]
where
1
, , , , , ,
2, , , 2 cos cos , , , ,
f w w f f
f
p w f n f e w w f np nn
e e e
S x y x y x y s
x n nS y y y s F x x x x S y y y s
x x x
[A-5a]
1
, , , , , , , ,
2, , , ,
2 cos cos , , , , ,
w w f f n mf nm
f
w f mp m
e
n f e w w f n mp nmn
e e
S x y x y x y s
xS y y y s
x
n nF x x x x S y y y s
x x
[A-5b]
132
Using Equations [A-5a] and [A-5b], Equation [A-4] can be rewritten as follows,
1
1
1
, , , , , , , , ,
4, , , 2 cos cos , , , ,
2 cos cos , , , ,
4 cos cos
w w w f f f
f f
p w f n f e w w f np nn
e e e e
m f e w w f mp mm
e e
n f e wn
e e
S x y z x y z x y z s
x z n nS y y y s F x x x x S y y y s
x z x x
m mF z z z z S y y y s
z z
n nF x x x x
x x
1
cos cos , , , , ,m f e w w f n mp nmm
e e
m mF z z z z S y y y s
z z
[A-6]
Since slab source is assumed, the source-shape-dependent rate in terms of
withdrawal rate is
ˆ8 f f f
x y z [A-7]
The pressure-rate-source function in the Laplace domain is described by Equations
[A-6] and [A-7],
133
1
1
1
, , ,
1, , , , , , , , ,
8
, , ,2
2 cos cos , , , ,
2 cos cos , , , ,
4
w w w f f f
t f f f
p w f
t e e f
n f e w w f np nn
e e
m f e w w f mp mm
e e
n f en
P x y z s
q sS x y z x y z x y z s
c x y z
q sS y y y s
c x z y
n nF x x x x S y y y s
x x
m mF z z z z S y y y s
z z
F x x
1
cos cos
cos cos , , , , ,
w
e e
m f e w w f n mp nmm
e e
n nx x
x x
m mF z z z z S y y y s
z z
[4.8]
where
2
, , ,f w e
p w f
e
sh y s ch y s ch y y sS y y y s
s sh y s
[4.9a]
2, , , ,
f n w n e n
w f np n
n e n
sh y s ch y s ch y y sS y y y s
s sh y s
[4.9b]
2, , , ,
f m w m e m
w f mp n
m e m
sh y s ch y s ch y y sS y y y s
s sh y s
[4.9c]
134
2, , , , ,
f n m w n m
w f n mp nm
n m
e n m
e n m
sh y s ch y sS y y y s
s
ch y y s
sh y s
[4.9d]
sin=
f e
n f e
f e
n x xF x x
n x x
[4.9e]
sin=
f e
m f e
f e
m z zF z z
m z z
[4.9f]
2
n en x [4.9g]
2
m em z [4.9h]
Equation [4.8] is based on the coordinates defined in Table 3.1 and 3.2. Equations
[4.8] to [4.9h] can be non-dimensionalized as,
1
1
1
, , ,
, , ,
2 cos cos , , , ,
2 cos cos , , , ,
4 cos
D D D D D
fD
fD p D wD fD D
eD fD
n fD eD wD D D wD fD nD Dp nn
eD eD
m fD eD wD D D wD fD mD Dp mm
eD eD
n fD eDn
P x y z s
xq s S y y y s
x y
n nF x x x x S y y y s
x x
m mF z z z z S y y y s
z z
nF x x
1
cos
cos cos , , , , ,
wD D
eD eD
m fD eD wD D D wD fD nD mD Dp nmm
eD eD
nx x
x x
m mF z z z z S y y y s
z z
[A-8]
where
135
2
, , ,fD D wD D eD D D
p D wD fD D
D eD D
sh y s ch y s ch y y sS y y y s
s sh y s
[A-9a]
2, , , ,
fD D nD wD D nD
D wD fD nD Dp n
D nD
eD D D nD
eD D nD
sh y s ch y sS y y y s
s
ch y y s
sh y s
[A-9b]
2, , , ,
fD D mD wD D mD
D wD fD mD Dp m
D mD
eD D D mD
eD D mD
sh y s ch y sS y y y s
s
ch y y s
sh y s
[A-9c]
2, , , , ,
fD D nD mD wD D nD mD
D wD fD nD mD Dp nm
D nD mD
eD D D nD mD
eD D nD mD
sh y s ch y sS y y y s
s
ch y y s
sh y s
[A-9d]
sin=
fD eD
n fD eD
fD eD
n x xF x x
n x x
[A-9e]
sin=
fD eD
m fD eD
fD eD
m z zF z z
m z z
[A-9f]
2
n eDn x [A-9g]
2
m eDm z [A-9h]
136
For the convenience of superposition principle, Equation [A-8] can be written as
follows,
, , , , ,
,
,, , ,i j m n m n m n i j
m n
D D D D D fD i jP x y z s q s F [A-10]
where,
, ,
, , , ,
, , , ,
,
,
1
1
, , ,
2 cos cos , , , ,
2 cos cos , , , ,
m n i j
i j m n m n i j
i j m n m n i j
fDm n
i j p D wD fD D
eD fD
n fD eD wD D D wD fD nD Dp nn
eD eD
m fD eD wD D D wD fD mD Dp mm
eD eD
xF S y y y s
x y
n nF x x x x S y y y s
x x
m mF z z z z S y y y s
z z
, ,
, , , ,
1
1
4 cos cos
cos cos , , , , ,
i j m n
i j m n m n i j
n fD eD wD Dn
eD eD
m fD eD wD D D wD fD nD mD Dp nmm
eD eD
n nF x x x x
x x
m mF z z z z S y y y s
z z
[A-11]
,
,
m n
i jF is the coefficient of single slab source solution of Segment #i in Fracture #j
relative to Segment #m in Fracture #n.