Download - Polaroid 600 and 600SE Repair Manual
Repair Manual
Americas Business CenterTechnical Services
201 Burlington RoadBedford MA 01730
TEL: 1.781.386.5309FAX: 1.781.386.5988
600SE ProfessionalPack Film CameraJune 1967
2
Table of Contents
Section Page
1 - Description ......................................................................................................... 8General ................................................................................................................ 8Major Assemblies of the Camera .......................................................................... 8Differences Between Models ................................................................................ 9Camera Features.................................................................................................. 9
2 - Operation ............................................................................................................ 17
Steps to Operate the Camera ............................................................................... 17Viewing and Focusing with the 127mm and 150mm Lenses.................................. 19Operation of the Viewfinder ................................................................................... 21Viewing and Focusing with the 75mm Lens and Accessory Viewfinder ................. 22
3 - Troubleshooting ................................................................................................. 24
Camera Checkout ................................................................................................. 27
4 - Disassembly/Assembly Procedures ................................................................. 29
General ................................................................................................................ 29Hand Grip Removal ............................................................................................... 30Removing the Hand Grip Flash Shoe (Model 600SE) ............................................ 31Disassembling the Hand Grip ............................................................................... 32Removing the Rangefinder Covers ........................................................................ 33Removing the Viewfinder Window Cover ............................................................... 33Releasing Screw from Holder Plate ....................................................................... 34Removing the Top Cover ....................................................................................... 34Removing the Accessory Shoe ............................................................................. 35Removing the Rangefinder Assembly .................................................................... 36Removing ghe Rangefinder/Viewfinder Windows .................................................. 38Removing Viewfinder Selector (Model 600SE Only) .............................................. 38Disassembly of Viewfinder Selector (Model 600SE Only)...................................... 39Removing Covers from Rangefinder Assembly (Model 600SE) ............................. 39Removing Covers from Rangefinder Assembly (Model 600 Only) .......................... 40Removing Framing Mask Assembly (Model 600SE Only) ...................................... 41Removing Framing Screen from the Parallax Frame (Model 600SE) ..................... 42Removing Framing Mask Assembly (Model 600) .................................................. 43Removing Framing Screen from the Parallax Frame (Model 600) .......................... 43Removing the Parallax Lever Assembly from the Rangefinder Assembly ............... 44Removing Objective Lens Assembly ..................................................................... 45Removing the Eyepiece Assembly ........................................................................ 45Removing Mirror Assembly from the Rangefinder Assembly .................................. 46
3
Removing Decorative Cover from Front Panel....................................................... 46Removing Inner Cover from Front Panel ................................................................ 47Removing 127mm Lens Assembly from the Model 600 Camea............................. 47Removing the Springs from the Bayonet (Model 600SE) ....................................... 47Removing the Bayonet (Model 600SE) .................................................................. 49Removing Locking Lever from Front Panel of Model 600SE Camera .................... 49Removing the Front Panel Leg .............................................................................. 50Removing Front Panel ........................................................................................... 51Removing Range Coupling Pin Assembly ............................................................. 51Removing the Flash Gun Bracket .......................................................................... 52Removing Leatherette and Plates from the Camera Body ..................................... 52Removing Tripod Socket ....................................................................................... 52Removing Sliding Locks........................................................................................ 53Removing Parallax Coupling Assembly ................................................................. 54Removing Range Lever Assembly......................................................................... 55Removing Range Lever Upper Spring ................................................................... 56Removing Middle Lever ........................................................................................ 56Removing Camera Body Sealing Sponges ........................................................... 56Removing Strap Eyelets ........................................................................................ 58Removing Flash Gun Mounting Socket .................................................................. 58Removing Grip Holder Socket ............................................................................... 59Removing Bottom Plates ....................................................................................... 59Removing the PC Flash Connector Socket............................................................ 60Removing the Seiko 884 Shutter from 127mm and 150mm Lens .......................... 60Disassembly of 127mm Lens Barrel ...................................................................... 63Disassembly of 150mm Lens Barrel ...................................................................... 64Disassembly of the 75mm Lens ............................................................................ 66Removing the Aperture Ring and Index Mark Ring ................................................. 68Removing the Focusing Ring................................................................................. 69Removing 75mm Lens, Depth of Field Scale Ring ................................................. 70Film Holder ........................................................................................................... 70
A. Mini-Roller Spread System Disassembly/Reassembly ................................... 72B. Adapter Frame-Disassembly/Reassembly ..................................................... 73C. Bail Latch-Disassembly/Reassembly ............................................................. 74D. Film Holder Door - Disassembly/Reassembly ................................................ 74
5 - Testing and Adjustments ................................................................................... 75
Light Leak Test ..................................................................................................... 75Shutter Speed Test ............................................................................................... 76RF/VF Parallax and Lens Collimation Tests .......................................................... 77Topside Test ......................................................................................................... 77Infinity Tube Tracking Test Procedure .................................................................... 79Aiming and Framing Target Test Procedures ........................................................ 82Near Distance Tracking Test Procedure................................................................ 87
6- Special Tools and Test Equipment ................................................................... 94
4
List of Illustrations
Figure Page
1-1 Major Assemblies of the Camera ..................................................................... 81-2 Location of the Rangefinder Assembly ............................................................. 91-3 Model 600SE Camera Features ...................................................................... 111-4 Model 600 Camera Features ........................................................................... 111-5 The 127mm f/4.7 Lens ..................................................................................... 131-6 The 150mm f/5.6 Portrait Lens ......................................................................... 141-7 The 75mm f/5.6 Lens with Wide Angle Viewfinder ............................................ 141-8 Polaroid Pack Film Holder ............................................................................... 152-1 Operating the Professional Pack Film Land Camera ....................................... 182-2 Framing A Picture............................................................................................ 192-3 Looking Through the Eyepiece......................................................................... 202-4 Operation of the RF/VF for the 127mm and 15mm Lenses ............................... 212-5 Mounting Accessory Viewfinder ....................................................................... 222-6 Locking Accessory Viewfinder on to Camera................................................... 234-1 Removing Film Holder and Lens Assembly, Model 600SE Camera ................. 294-2 Hand Grip Removal ......................................................................................... 304-3 Removing Hand Grip Flash Shoe and Cable Release Rack (Model 600SE) ... 314-4 Hand Grip Exploded View ............................................................................... 324-5 Removing Viewfinder Selector Switch.............................................................. 334-6 Removing Viewfinder Window Cover ............................................................... 334-7 Removing Holder Plate Screw from Viewfinder Window .................................. 344-8 Removing the Viewfinder Cover ....................................................................... 344-9 Location of Rangefinder Adjusting Screws ....................................................... 354-10 Removing Shoe and Holder Plate .................................................................... 354-11 Unhood Spring, Remove Anchor Screw ........................................................... 364-12 Removing Screws Securing Viewfinder Assembly to Camera Body ................. 364-13 Removing Rangefinder Assembly from Camera Body...................................... 374-14 Location of Parallax Eccentric Adjusting Screw................................................ 374-15 Removing Rangefinder/Viewfinder Windows ................................................... 384-16 Removing Viewfinder Selector ......................................................................... 384-17 Parts of the Viewfinder Selector ....................................................................... 394-18 Removing cover from Rangefinder Assembly (Model 600SE) .......................... 404-19 Removing cover from Rangefinder Assembly (Model 600 Only) ....................... 404-20 Removing Framing Mask Spring ...................................................................... 414-21 Removing Framing Mask Assembly (Model 600SE) ........................................ 424-22 Removing Framing Screen from Parallax Frame (Model 600SE) ..................... 424-23 Removing Framing Mask Assembly (Model 600) ............................................. 434-24 Removing Framing Screen from parallax Frame (Model 600) .......................... 434-25 Removing Parallax Lever Assembly from the Rangefinder Assembly ............... 444-26 Removing Objective Lens Assembly ................................................................ 444-27 Disassembly of the Eyepiece........................................................................... 454-28 Removing Mirror Assembly .............................................................................. 46
5
4-29 Removing Decorative Cover from Front Panel (Model 600).............................. 464-30 Removing Inner Cover from Front Panel (Model 600) ....................................... 474-31 Removing the 127mm Lens Assemblly from Model 600 Camera ..................... 484-32 Removing Springs from Bayonet ...................................................................... 484-33 Removing the Bayonet from the Model 600SE Camera ................................... 494-34 Removing Locking Lever from Front Panel of Model 600SE Camera ............... 504-35 Removing Front Panel Leg .............................................................................. 504-36 Removing Front Panel ..................................................................................... 514-37 Removing Range Coupling Pin Assembly ........................................................ 514-38 Removing Flash Gun Bracket and Leatherette ................................................. 524-39 Removing Tripod Socket ................................................................................. 534-40 Removing Slliding Locks ................................................................................. 534-41 Removing Parallax Coupling Assembly ............................................................ 544-42 Removing Range Lever Assembly ................................................................... 554-43 Removing Range Lever Upper Spring.............................................................. 564-44 Removing Middle Lever ................................................................................... 574-45 Removing Camera Body Sponge .................................................................. 574-46 Removing Strp Eyelets .................................................................................... 584-47 Removing Flash Gun Mounting Socket ............................................................. 584-48 Removing Grip Holder Socket ......................................................................... 594-49 Removing Bottom Plates ................................................................................. 594-50 Removing the PC Flash Connector Socket ...................................................... 604-51 Loosening Shutter Retaining Nut with Special Tool NHo. 12459 ....................... 614-52 Disassembly of Front End of 127mm and 150mm Lens Barrel ......................... 624-53 Removing Speed Mark Ring ............................................................................ 624-54 Disassembly of Rear of Lens Barrel, 127mm Lens........................................... 634-55 Removing Range Coupling Key, 127mm Lens ................................................. 644-56 Disassembly of Rear of Lens Barrel, 150mm Lens........................................... 654-57 Front Lens Assembly, 75mm Lens ................................................................... 664-58 Rear Lens Assembly, 75mm Lens ................................................................... 664-59 Removing Retaining Nut from Shutter, 75mm Lens........................................... 674-60 Removing Aperture Ring and Index Mark Ring ................................................. 684-61 Removing Focusing Ring ................................................................................. 694-62 Removing the 75mm Lens, Depth of Field Scale Ring...................................... 704-63 Removing Spread System Springs .................................................................. 714-64 Roller Bearing Blocks ...................................................................................... 714-65 Mini-Roller Spread System .............................................................................. 724-66 Film Holder Parts ............................................................................................. 745-1 Camera Set-Up for Infinity-Tube Tests.............................................................. 775-2 Perfect Image of Infinity Target Seen through the Viewfinder at Infinity .............. 785-3 Split Image Seen through Viewfinder ............................................................... 785-4 Location of Topside Adjusting Screw ............................................................... 795-5 Marking "Image Coincidence" at Infinity ........................................................... 795-6 Infinity-Tube Target as Seen Through Focal Plane Loupe ................................. 815-7 Measuring Collimation Tracking Error at Infinity ................................................ 815-8 The Reporter Aiming and Framing Target ........................................................ 82
6
5-9 Camera Lined Up with Aiming Circle ............................................................... 845-10 Line Up Albada Lines with Framing Target ...................................................... 845-11 Sighting for Parallax Test for 75mm Lens ........................................................ 855-12 Aiming Measurement ....................................................................................... 855-13 Preparation for Aiming Adjustment .................................................................. 865-14 Adjusting Aiming of 75mm Accessory Viewfinder by
Repositioning Accessory Shoe ................................................................. 865-15 Adjusting Distance Scale on 75mm Accessory Viewfinder ............................... 875-16 Shim Adjustment to 75mm Accessory Viewfinder ............................................ 875-17 Camera Setup for Near Distance Collimation Test ........................................... 885-18 Marking Image Coincidence at Near Distance ................................................. 885-19 Measuring Collimation Tracking Error at Near Distance ................................... 895-20 Access to Infinity Range Adjustment ................................................................. 915-21 RF/VF Near-Distance Eccentric Screw Adjustment.......................................... 915-22 Location of Lens Barrel Couping Pin Adjustment ............................................. 915-23 Loosening Front Lens Lock Ring ..................................................................... 926-1 Collimator, No. 11431 ...................................................................................... 946-1 Focal Plane Plate No. CCR-12262 .................................................................. 946-2 Test Targets .................................................................................................... 956-3 Special Tools .................................................................................................. 95
List of TablesTable Page
1-1 Differences Between the Model 600 and 600SE Cameras ................................ 101-2 Lenses .............................................................................................................. 121-3 Polaroid Land Pack Films for Model 600/600SE Cameras ............................... 165-1 Model 600/600SE Camera Tests ...................................................................... 755-2 Allowable Range of Shutter Speeds .................................................................. 765-3 Parallax Adjustments ......................................................................................... 906-1 Special Tools and Test Equipment .................................................................... 94
7
NOTES
8
1- Description
General
The Polaroid Land Models 600 and 600SE Professional Pack Film Cameras are non-foldingcameras designed for the professional photographer. They use a removable Polaroid pack filmholder which accommodates Polaroid pack film holder which accommodates Polaroid type100/600 Land Film.
Major Assemblies of the Camera
Each camera has three major assemblies (Figure 1-1). The camera body and handle, the lens-shutter assembly and the film holder.
Figure 1-1. Major assemblies of the camera
The camera body with handle attached support the film holder and the lens-shutter assembly.The camera body houses the rangefinder assembly as shown in Figure 1-2. The rangefinderassembly has a built-in viewfinder. It is referred to as the RF/VF (rangefinder/viewfinder).
Film Holder
Camera BodyWith Handle
Camera Body Cap
Lens Assembly
9
Figure 1-2. Location of the rangefinder assembly
Differences Between Models
A summary of the differences between the two models is contained in Table 1-1. The basiccamera is 7" high, 7" deep and 9" wide (18cm X 18cm X 18cm X 24cm) (including hand grip).The weight including the pack film holder is about five pounds (2.2 kg). Additional weightinformation is included in Table 1-1.
Camera Features
These professional pack film cameras have the following features, most of which are identifiedin Figure 1-3 and Figure 1-4.
Carrying Straps - Strap eyelets are provided on the body of the camera to allow theaddition of a neck strap. An adjustable had strap is provided onthe hand grip.
Tripod Socket - The bottom of the camera body has a socket which accepts a1/4-20screw, for mounting the camera onto a tripod.
Top Cover
Rangefinder Assembly
Camera BodyFace Plate
RF/VF Window Cover
10
Table 1-1. Differences between the model 600 and 600SE cameras
Model 600 (Figure 1-3) Model 600SE (Figure 1-4)
Fixed 127mm lens. Interchangeable lenses: 75mm and 150mm
(Table 1-2).
Not applicable Red dot on camera body and on each of theinterchangeable lenses.
Cold shoe on the hand grip. This is identified as hand gripflash shoe in Figure 1-2. It is used for mounting the flashunit when the 75mm viewfinder is occupying the accessoryshoe on the camera body.
Cable release holder on hand grip.
Camera body cap and rear lens cap.
Viewfinder frame is set for 127mm lens only. Viewfinder frame can be selected for 127mm and150mm lenses. *
Viewfinder selector switch.
Viewfinder indicator.
Chrome cable release. Vinyl hand strap. Black chrome cable release. Leather hand strap.Narrow vinyl neckstrap. Wide woven neckstrap.
Model 600 with empty film holder: 4 pounds, Model 600SE without lens or film holder: 2 pounds,10 ounces; (2.1 kg). 14 ounces; (13 kg).
LENSES:
127mm: 1 pound, 3 ounces; (.54 kg)150mm: 1 pound, 5 ounces; (.58 kg)75mm: 1 pound, 6 ounces; (.6 kg)* 75mm viewfinder: 6 ounces; (1.7 kg)
* The height of the model 600SE with the 75mm viewfindermounted onto the accessory shoe is 9 1/2 inches; (25 cm).
WEIGHTS: Film holder without film pack: 14 ounces; (.4 kg). Film pack: 4 ounces; (11 kg).
11
Figure 1-3. Model 600SE camera features
Figure 1-4. Model 600 camera features
Eyecup
Flash BracketMount
Film HolderLock
BayonetLens Mount
Neck StrapEyelets
Flash and ViewfinderAccessory Shoe
Red Dot *
RangefinderCoupling Pin
Shutter Release
Lens ReleaseButton
Cable Release
Hand Strap
Hand Grip
Hand GripFlash Shoe *
Tripod Socket
Cable ReleaseHolder
ViewfinderIndicator
ViewfinderSelector Switch
Eyecup
Eyepiece
Eyecup
Film Holder Lock
Flash Bracket Mount
Neck Strap Eyelets
Bail Latch
Film Tab Slots
Accessory ShoeNeck Strap
Viewfinder Windows
Shutter Release
Hand Grip
Hand Strap(Adjustable)
Depth of field Scale
Distance Scale
Focusing Ring
Shutter Cocking Lever
Shutter Speed Ring
Aperture Control Ring
PC FlashConnector Socket
Cable Release
127MM Lens
12
Lenses - The Model 600 Camera has a 127mm f/4.7 lens (Figures 1-5through 1.7). Two additional interchangeable lenses are available forModel 600SE (Table 1-2).
The interchangeable lenses use a bayonet type mount for attaching tothe camera body. A lens release button locks the lens to the camerabody.
The lenses are fully coated and color corrected. Each is in a shutter thatallows exposure control with a wide range of shutter speed/aperturecombinations.
All lenses are equipped with Seiko between-the-lens shutters. Each lenscomes with front and rear lens caps and a collapsible rubber lens hood.
Table 1-2. Lenses
Detail\Lens 127mm f/4.7 lens 75mm f/5.6 lens * 150mm f/5.6 lens (Normal) (Wide Angle) (Portrait)
Lens Construction 3 Groups 4 Groups 3 Groups4 Elements 7 Elements 4 Elements
Apertures f/4.7 to f/64 f/5.6 to f/45 f/5.6 to f/45
Closest Focusing Distance 3.5 ft. (1.1m) 3.3 ft. (1m) 6.6 ft. (sm)
Angle of View 41 Horizontal 65 Horizontal 35 Horizontal
Screw-in Filter Size 55mm 72mm 55mm
Note: The 75mm lens comes with an accessory viewfinder.
Shutter - Seiko "S" shutters are contained within the lenses, providing shutterspeeds from 1 /500 sec to 1/sec, plus bulb and "X" synchronization.
The setting of shutter speeds is possible with the shutter in the uncockedor cocked position.
The shutter has a "B" (bulb) setting for time exposures. This allows theshutter to be held open as long as the exposure release is held down.
"X" synchronization allows the flash contacts to close when the shutter isfully open, at all shutter speed settings.
13
Filters - Model 600 and 600SE lenses accommodate standard screw-in filters(Table 1-2) for correct screw-in filter size.
Viewfinder - Both models 600 and 600SE cameras are equipped with acoincidence-type rangefinder in which two images come together withina circle when in focus.
The focusing range is from 3.5 feet (1.1 meter) to infinity.
The model 600SE camera has a single window, superimposed coupledrangefinder with a bright frame that moves for parallax correction.Framing lines within the finder can be selected for the 127mm and150mm lens fields-of-view.
A 75mm parallax corrected viewfinder supplied with the 75mm lens can bemounted on top of the rangefinder area of the model 600SE camera body(Figure 1-7).
The model 600 camera rangefinder/viewfinder has framing lines for the127mm lens only.
Figure 1-5. 127mm f/4.7 lens (features called out are commonto 75mm and 150mm lenses)
ApertureControl Lever
Cable ReleaseSocket
Shutter CockingLever
ApertureControl Ring
ShutterSpeed Ring
FocusingRing
DistanceScale
Depth of FieldScale
Red DotLens Assembly
PC FlashConnector
Socket
PC FlashConnector
Socket Rubber LensHood
Rear LensCap
Lens Cap
14
Figure 1-6. 150mm f/5.6 portrait lens
Figure 1-7. 75mm f/5.6 portrait lens with wide angle viewfinder
Lens Assembly
Lens Cap
Rubber LensHood
Rear LensCap
Rear LensCap
Lens Assembly
Rubber LensHood
Lens Cap
Accessory WideAngle Viewfinder
15
Film Holder - The model 73 Land film holder is used to hold the pack film in the camera.The films used in model 600/600SE cameras are described in Table 1-3.
Sliding locks hold the film holder to the camera body.
The film holder contains a dark slide to prevent film exposure whenremoving the film holder from the camera.
A standard A-11 mini-roller spread system is used in the holder.
Figure 1-8. Polaroid pack film holder
Bail Latch
CameraMounting Brackets
Type 73Film Holder
Dark Slide
16
Table 1-3. Polaroid Land pack films for model 600/600SE cameras
Film Speed (approx. DescriptionType ASA/DIN equiv.)
Types 668/108 75 ASA/20 DIN These films yield a positive color print.Polacolor 2 They are balanced for use in average
daylight and with electronic flash unitsapproximating average daylight (5500K).Ideal for both outdoor and studio photography.
Types 084/107 3000 ASA/36 DIN Very high speed black and white films, whichBlack and White yield a positive print. Ideal for general purpose
photography, recording high speed events orlow-light situations. Panchromatic. Printsmush be coated.
Types 667/107C 3000 ASA/36 DIN Similar to the above, but prints need not beBlack and White coated after development.Coaterless
Type 665 75 ASA/20 DIN A black and white film which produces a high-Positive/Negative resolution negative, in addition to a high
quality positive print. Ideal for general purposephotography where a medium contrast instantprint and a permanent negative are desired.Panchromatic. Prints must be coated.
Note: Each pack produces eight (8) prints, 3 1/4 x 4 1/4 in. (8.3x10.8cm). Type 665 filmproduces a usable negative as well.
17
2 - Operation
Steps to Operate the Camera (Figure 2-1)
• Mount flash attachment.
• Select and mount lens (model 600SE only).
• Position viewfinder selector switch to 127 or 150.
• Mount filter.
• Load film.
• Remove dark slide.
• Frame the subject in the viewfinder.
• Focus.
• Set the shutter speed and lens aperture.
• Cock the shutter lever.
• Depress the shutter release.
• Pull white paper tab.
• Pull yellow film tab.
• Time development of film.
• Peel finished photograph from yellow tab.
• Repeat sequence for each picture until the pack is emptied.
• Change film holder, lens, flash attachment, filter, etc., as required, between photographs.
18
Figure 2-1. Operating the professional pack film land camera
The shutter blades are closed until the shutter release button is pressed. When the shutter releaseis pressed, scene light passes through the lens, through an opening in the shutter blades and ontothe film in the film holder (Figure 2-2). The dark slide must be removed to allow scene light toreach the film.
1. Be sure the dark is removed. Look through theviewfinder to frame the picture. Set the focus.
Measure the light.
127
3. Read the distance to the objecton the distance scale.
5 ft. (1.5 m)
- 7 Feet- 5 Feet- 4 Feet
Near Limit4 Feet
Far Limit7 Feet
DistanceScale
Depth of FieldScale
ApertureNumber
4545
Locate the aperture number on both side of the red focusmark on the depth of field scale. Follow the white line up tothe distance scale and read the near and far limits of yourzone and sharp focus.
2. Set the shutter speed and lens aperture.
4. Shoot!
Cock theShutter Lever
Click
Depress the Shutter Release
19
Figure 2.2. Framing a picture
Viewing and Focusing with the 127mm and 150mm Lenses
The image shown in Figure 2-3 can be seen by looking through the eyepiece of either the model600 or model 600SE cameras.
In the model 600SE camera the viewfinder frame is adjustable for the 127mm and 150mm lenses.The number that appears just below the top right framing line indicates the lens that has beenselected. Sliding the selector switch to the other position ;changes the framing image to matchthe focal length of the other lens. A lens indicator number does not appear in the model 600image area.
Accessory Wide Angle Viewfinder
Viewing angle changes withdistance setting.
75 MMWide Angle Lens
ShutterBlades
RubberLens Hood
Bright Frame
Subject
Dark Slide blocks lightunless it is removed.
Film Holder
Film Pack Camera Body
Normal Lens Assembly127mm or 150mm
Height of framing lineschanges with distance setting.
Focusing circle is abovecenter at close up setting.
Focusing circle iscentered at infinity setting.
Under 10 feet, composewithin framing lines.
Over 10 feet, composewithin framing dots.
20
The framing lines, framing dots and coincidence image circle appear as bright yellow light in yourfield of vision.
For close up photographs of 10 feet or less, the picture is composed within the framing linesshown. When focusing beyond 10 feet, the picture is composed within the limits of the eightframing dots.
The Models 600 and 600SE are equipped with a coincidence-type rangefinder in which twoimages come together within a circle when in focus. Familiarize yourself with it by setting the lensat infinity. Now focus on a nearby subject.
View your subject through the bright yellow circle in the viewfinder. Position your eye so the entirecircle is visible. Within the circle your subject will appear as tow images. Turn the focusing ring sothat these two images coincide. Now the camera is focused on your subject.
Figure 2-3. Looking through the eyepiece
Viewfinder Indicator *
Viewfinder Selector Switch *
Note: Double image camera isnot focused on subject.
Framing Lines
Framing Dots
Field of Vision
* Model 600SE Only
127
127
Lens Indicator *
21
Operation of the Viewfinder
The construction of the viewfinder built into the model 600 and 600SE camera is shown inFigure 2-4. The model 600 has framing lines for the 127mm lens only. The model 600SE has twosets of framing lines and lens indicators for the 127mm and 150mm lenses.
Figure 2-4. Operation of the RF/VF for the 127mm and 150mm lenses
The framing lines are contained on a piece of film. Light passes through the frosted glass windowand through the film containing the framing images.
The desired bright yellow color of the framing image results from the color of the beam splitter.
RangefinderWindow
Angle changes as focusdistance setting changes.
MovableMirror
Fixed Mirrorwith Hole
MagnifyingFrame
MovableImage
FixedImage
Eyepiece
BeamSplitter
ObjectiveLens
Subject
Light
FrostedGlass
MetalMask
Film withFraming Images
127 150
22
On the model 600SE, a metal mask (with a pattern of holes) blocks the light from one of theframing images. Moving the viewfinder selector switch moves this metal mask to reveal oneframing image on the film, and blocks the other framing image.
As the camera is focused from infinity to close up, the rangefinder coupling pin moves the framing-mask assembly. This causes the framing line image to move down, as shown in Figure 2-2. Thiscompensates for the change of viewing angle, between the camera lens and the viewfinder lens.
At the same time the rangefinder coupling pin pivots the movable mirror. This moves the movableimage from left to right. When the movable image coincides with the fixed image in the focusingcircle, the camera is in focus.
Viewing and Focusing with the 75MM Lens and Accessory Viewfinder
An accessory wide angle viewfinder is supplied with the 75mm wide angle lens. Figure 2-5shows the accessory viewfinder ready to be attached to the cold accessory shoe on top of thecamera.
Note: It is possible to attach an accessory viewfinder incorrectly. Avoid attaching the viewfinderpartially unlocked or backwards. Do not attach the accessory viewfinder to the hand gripflash shoe.
Figure 2-5. Mounting accessory viewfinder
Avoid a partially locked lockingscrew interfering with fullinsertion of the mounting baseinto the shoe.
Slide on the accessoryviewfinder from rear ofcamera.
" Wrong "
Eyecup
Guide Spring
Accessory shoeon top of camera
" Right "
Locking screw in unlocked (top most)position. Square recess on mounting baseis clear to accept stopper screw.
Stopper Screw
23
Unlock the viewfinder by turning the locking screw opposite to the direction of the arrow on theviewfinder. When fully unlocked, the locking screw can be seen in its topmost position. If thislocking screw is partially down, it will prevent the viewfinder from being fully seated on theaccessory show. Slide the chrome mounting base of the viewfinder into the accessory shoe.Push forward until the stopper screw on the accessory shoe is inside the square recess on themounting base.
Note: The viewfinder may feel snug and secure before it is fully seated. This is because it is heldby the guide springs on the accessory shoe. Do not leave it in this partially lockedcondition. The picture framing would be faulty and the viewfinder could be knocked off thecamera.
The locking screw should be on top of the stopper screw as shown in Figure 2-6. Turn the lockingscrew as far as it will go in the direction of the lock arrow. The viewfinder is now secured to thetop of the camera.
Figure 2-6. Locking accessory viewfinder on to camera
" Right "
Locking screw is locked on top of stopperscrew. Mounting base is fully inserted intoaccessory shoe.
24
3 - Troubleshooting
Persons unfamiliar with Polaroid Model 600 and 600SE cameras should read Sections 1 and 2 togain an adequate background of camera operation and features. Reference to thesetroubleshooting charts should be sufficient to diagnose camera problems in most cases. Themethods of implementing the corrective actions are detailed in Sections 4 and 5.
Problems Evidenced in Pictures
Problems Probable Cause Corrective Action
Picture completely 1. Dark slide in. 1. Remove dark slide.black. 2. Lens cap on. 2. Remove lens cap.
3. Object in focal plane. 3. Examine film holder, camera body andshutter-lens assembly.
4. Defective film. 4. Replace film.5. Shutter defective. 5. Repair or replace shutter.
Pictures constantly 1. RF/VF tracking 1a.Perform rangefinder infinity rangeout of focus. discrepancy. adjustment.
1b.Repair or replace RF/VF, if necessary.
2. Lens out of collimation. 2. Collimate lens.3. Lenses loose. 3. Install lenses properly.4. Lenses smeared. 4. Clean lenses thoroughly.5. Lenses cracked. 5. Replace lenses.6. Focusing linkage bent. 6. Replace linkage components7. Film holder or film 7. Reseat or replace film holder. Inspect
holder adapter plate seating of film holder adapter plate,not properly seated. tighten screws.
Picture either too Camera not calibrated 1. Test shutter speeds.dark or too light. properly. 2. Observe aperture openings.
3. Repair or replace shutter.
Pictures have a 1. Dark slide covering 1. Position dark slide with onlydark line along part of negative. approximately 1/4" of metal slideone side showing.
2. Film holder not seated 2. Reset film holderproperly
25
Problems Evidenced in Pictures (Con't)
Problems Probable Cause Corrective Action
Picture fogged 1. Sponge filters missing 1. Replace filler sponges on camera(light leak). from camera body. body
2. Film holder door hinge loose 2. Repair or replace door on filmor broken. holder or replace film holder.
3. Camera body cracked. 3. Repair or replace camera body.
Pictures are light 1. Improperly seated film 1. Reseat film holder.struck in one area holder.
2. Improperly seated film 2. Reset film holder adapter plate.adapter.
3. Improperly seated filmpack. 3. Reseat film pack.
4. Cracked film holder. 4. Replace film holder5. Failure to completely close 5. Make sure dark slide is fully
from camera dark slide closed before removing thebefore removing film holder. film holder form camera.
6. Screws loose on film holder 6. Tighten screws on film holder base. base.
7. Film holder springs weak 7. Replace film holder.or broken.
8. Missing or deformed light 8. Replace light seals.seals.
9. Shutter not closing fully. 9. Check for defective shutter cableand/or actuating mechanism.If defective, replace. If OK., repairor replace shutter.
Pictures not properly 1. RF/VF framing error. 1. Perform RF/VF framingframed. adjustments.
2. RF/VF defective. 2. Repair or replace RF/VF
26
Problems with Film Holder
Problems Probable Cause Corrective Action
Bad spreads. 1. Rollers dirty. 1. Clean rollers (instruct customer).2. Rollers nicked or scratched 2. Replace A-11 mini-roller
assembly.
Film tearing 1. Exit door malformed 1. Replace film holder.(not opening properly).
2. Edge control on mini- 2. Repair or replace mini-rollerroller defective. assembly.
Film holder door not 1. Bail latch bent. 1. Replace bail latch.latching securely 2. Bail latch eyelets "floating". 2. Replace door assembly.(light leaks in picture) in door assembly.
3. Door hinge post on film 3. Replace film holder.holder broken.
Problems with Viewfinder
Problems Probable Cause Corrective Action
Faulty image in 1. Viewfinder lenses 1. Repair or replace defective parts. viewfinder. scratched, broken or Replace viewfinder assembly.
out of place.
Lens indicator not 1. Defective framing mask 1. Repair and readjust framing maskvisible. assembly. assembly.
Problems with Viewfinder
Problems Probable Cause Corrective Action
Shutter will not trip. 1. Defective release cable. 1. Repair or replace release cable.2. Defective shutter. 2. Repair or replace shutter.
Shutter will not cock. 1. Defective shutter. 1. Repair or replace shutter.
27
Camera Checkout
This section of the manual deals with the detailed inspection of the cameras. It will guide arepairman through a complete camera checkout. This is a required procedure for every camerareceived for repair. For the location of parts, refer to the Figures in Sections 1 and 4.
1. Examine the Neckstrap
Look for signs of excessive wear or faulty fastening rivets, tension slides, or keepers. Checkthat the D-rings are properly closed, holding the strap securely. Also be sure that the straplugs are properly secured in the camera body.
2. Examine the Exterior of the Camera Body and the Film Holder
a. If there are dents or cracks in the body or film holder, be sure that they don't interfere withoperation of the camera. Perform light leak test.
b. Inspect the tripod socket for stripped threads.
c. Examine action of film holder locks on both sides of camera.
d. Inspect bayonet lens mount for damage or defective springs.
e. Examine the viewfinder selector switch on the Model 600SE camera. Move the switch tothe 127 and 150 positions. Number in framing image should agree with selected number.
3. Examine the Film Holder Bail Latch
Unlatch the rear door from the film holder. Check the action of the release latch to be sure itdoesn't bind. Check the hinge area for excessive gap between the door and hinge. Close therear door and be sure both sides latch properly.
4. Examine the Film Holder Door Assembly
Release the rollers and pull them up out of the way. Look for broken plastic at the ends of thedoor. BE SURE THE ENTIRE EXIT DOOR AREA IS CLEAN.
5. Examine the A-11 Mini-Roller Assembly
With the rollers still in the unlatched position, examine them very closely for nicks, scratches, orencrusted foreign matter. Clean the rollers thoroughly. (NEVER USE ANYTHING WHICHCAN SCRATCH THE ROLLERS.) Be certain none of the parts is bent out of shape.
Note: Use only water to clean the rollers.
28
6. Examine the Rangefinder/Viewfinder (RF/VF)
Inspect the lenses to be sure they are not cracked, scratched or dirty. Move lens focus ringwhile looking through eyepiece. Inspect for smooth tracking of lens setting by the rangefinder.Perform parallax framing and tracking discrepancy tests.
7. Examine the Lens
Be sure the lens is not scratched. Clean the lens thoroughly. Move the focus ring; feel smoothaction. Perform lens collimation tests.
Note: Do not force or twist the lens barrel. It is very easy to damage thehelicoid assembly.
8. Examine the Shutter Action
Cock the shutter. Press the shutter release button. The shutter should trip when the shutterrelease button is pressed. Shutter speeds must be read on a speed tester.
29
4- Disassembly and Assembly
General
Disassembly and reassembly of both the model 600 and 600SE cameras is covered in thissection. Instructions apply to both models unless otherwise indicated. The differences betweenmodel 600 and model 600SE camera are covered in Section 1.
The disassembly and repair of the film holder is covered at the end of this section. The film holdercan easily be removed from the camera by unlocking two sliding locks on the side of the camera.
The lens assemblies for the model 600SE camera are removable and interchangeable. A lens can be easily removed by pushing the lens release button and rotating the lenscounterclockwise (Figure 4-1).
Figure 4-1. Removing film holder and lens assembly, model 600SE camera
The lens assembly for the model 600 camera should be removed for repair or replacement only.Instructions are included for the replacement of the shutter assemblies. Detailed disassembly ofthe shutter assembly components are not included in the manual.
Screws, light seals and some other parts are glued into position. Use trichlorethylene to freescrew threads and to dissolve or remove glue. Use Pliobond adhesive to glue parts atreassembly. Use Molycote or Lubriplate to lubricate parts as required.
Film Holder Lock
Lens Release Button
30
Hand Grip Removal (Figure 4-2)
The model 600SE hand grip has a cable release holder and flash shoe attached. It also has ablack chrome cable release. The model 600 has a chrome cable release. Otherwise the hadgrips are the same.
Note: Work on a soft surface, so the surfaces on the camera and film holder are not damaged.
a. Remove the film holder from the camera.
b. Remove the set screw in the stem of the left hand grip, using a 1/16" (.16 mm) widescrewdriver with a sharp edge to fit into the narrow slotted headless set screw.
c. Drive the knock pin through the left hand grip stem using a 1/8" (.32 mm) punch.
d. Slide the hand grip assembly off the grip holder socket attached to the camera body.
e. After reassembly, screw the end of the cable release into the shutter socket. Cock andrelease the shutter several times to ensure proper assembly and operation.
Figure 4-2. Hand grip removal
Cable Release Holder
Hand Grip
Left HandGrip Stem
Grip HolderSocket
Set Screw
Knock Pin
31
Removing Hand Grip Flash Shoe (Model 600SE) ( Figure 4-3)
a. Remove stopper screw.
b. Remove shoe cover.
c. Remove the four (4) screws holding the shoe and the cable release rack.
Figure 4-3. Removing hand grip flash shoe and cable release rack (model 600SE)
Stopper ScrewShoe Cover
Screws (4)Hand Grip
Flash Shoe
Cable ReleaseRack
Hand Grip
32
Disassembling Hand Grip (Figure 4-4)
a. Remove screw and belt plate (2); fold grip belt (8) back out of the way.
b. Remove two screws (3) and separate right hand grip (4) from the assembly.
c. Slide plate (5) off of grip (4) and remove screw (6), belt plate (7), and grip belt (8).
d. Hold spring (11) and remove two screws (9), cable release (10), and spring (11).
e. Lift off washer (12), plate (13), and disc (14).
f. Lift off trigger (16) and separate stopper (15) from the trigger.
Figure 4-4. Hand grip exploded view
12
3
8
45
1216
15
1714 13
9 6
7
10
11
1. Screw2.. Belt Plate3. Screw4. Right Hand Grip5. Plate6. Screw7. Top Belt Plate8. Grip Belt9. Screw (2)10. Cable Release11. Spring12. Washer13. Plate14. Disc15. Stopper16. Trigger17. Left Hand Grip
33
Removing Rangefinder Covers (Figures 4-5 through 4-8)
The rangefinder/viewfinder can be removed from model 600 and 600SE cameras without remov-ing any other major assembly. The viewfinder window cover and the top cover can be removed toallow inspection and adjustment.
On the model 600SE camera, move the viewfinder indicator to the 150 position to give access toan anchor screw securing the rangefinder assembly to the camera body. Remove screw andbutton shown in Figure 4-5.
Figure 4-5. Removing viewfinder selector switch
Removing Viewfinder Window Cover (Figure 4-6)
The viewfinder window cover can be removed for inspection, cleaning and repair of viewfinderwindows. Remove two (2) screws (Phillips head) holding viewfinder window cover to camera frontpanel.
Figure 4-6. Removing viewfinder window cover
Viewfinder Indicator
Viewfinder Selector Switch
Screw and Button
CameraFront Panel
Screws
Viewfinder WindowCover
34
Releasing Screw from Holder Plate (Figure 4-7)
Lay camera on a soft surface, with viewfinder windows facing up. Remove Phillips head screwshown in Figure 4-7.
Figure 4-7. Removing holder plate screw from viewfinder window
Removing Top Cover (Figure 4-8)
Complete part removal shown in Figures 4-5 through 4-7. Remove three (3) Phillips head screwsand three plastic washers holding cover to camera body. Lift and remove top cover.
Figure 4-8. Removing viewfinder cover
Holder Plate Screw
Cover
35
The viewfinder assembly is now partially exposed for inspection, cleaning or adjustment (Figure 4-9).Note: Do not turn screws without first determining if they are adjusting screws.
Refer to Section 5 before attempting adjustments.
Figure 4-9. Location of rangefinder adjusting screws
Removing Accessory Shoe (Figure 4-10)
Remove stopper screw. Slip shoe cover off shoe. Remove four (4) screws holding shoe andholder plate to top cover.
Figure 4-10. Removing shoe and holder plate
Near Distance RangeAdjusting Screw
TopsideAdjusting Screw
Infinity RangeAdjusting Screw
Stopper ScrewShoe Cover
Screw (4)
Shoe
Cover
Holder Plate
36
Removing Rangefinder Assembly (Figures 4-11 through 4-13)
On the model 600SE, slide the bar marked 127 150 away from the eyepiece. Unhook spring.Remove anchor screw.
Figure 4-11. Unhook spring, remove anchor screw
Place camera in vertical position. Remove two screws, shown in Figure 4-12.
Figure 4-12. Removing screws securing viewfinder assembly to camera body
SpringAnchor Screw
Retaining Screw
Retaining Screw
Anchor Screw
37
Lift rangefinder assembly from the camera body as shown in Figure 4-13.
Figure 4-13. Removing rangefinder assembly from camera body
Note: Do not loosen the eccentric screws or the parallax relay lever screw, withoutreferring to instructions covering parallax adjustment in Section 5 (Figure 4-14).
Figure 4-14. Location of parallax eccentric adjustment screw
Anchor Screws Screws (2)
Rangefinder Assembly
Camera Body
Camera Body
Range Eccentric Screw
Screw
Parallax Relay Lever
Camera Front PanelParallax Eccentric Screw
38
Removing Rangefinder/Viewfinder Windows (Figure 4-15)
Peel the felt light baffle from the back of the camera front panel. Gently press out glass windowsand screen. Gently pry out metal masks. Reassembly requires removal of old adhesive. ApplyPliobond adhesive to front panel. Clean glass and screen before cementing parts into recessesin front panel.
Figure 4-15. Removing rangefinder/viewfinder windows
Removing Viewfinder Selector (Model 600SE Only) (Figure 4-16)
Remove two screws as shown in Figure 4-16.
Figure 4-16. Removing viewfinder selector
Light Baffle (Felt)
Screen
Mask (Metal)
Objective Windows (Glass)
Framing Mask (Metal)
Rangefinder Window (Glass)
Glass
Viewfinder Selector
Screw (2)
Rangefinder
Guide Screw
39
Disassembly of Viewfinder Selector (Model 600SE Only) (Figure 4-17)
Remove the guide screw shown in Figure 4-16. Slide the top of the assembly out from under thedetent spring. In reassembly, apply a small amount of Lubriplate between the two detent slots.
The assembly relationship of the parts of the viewfinder selector is shown in Figure 4-17. Theposition of the detent spring affects the position of the lens number (127 or 150) shown at theviewfinder indicator.
The position of the metal mask driver affects the position of the metal mask as it blanks or revealsthe framing image.
Note: Perform aiming and framing tests and adjustment after reassembly.
Figure 4-17. Parts of the viewfinder selector
Removing Covers from Rangefinder Assembly (Model 600SE Only) (Figure 4-18)
Pry plate from eyepiece assembly area. Remove single screw, shown in Figure 4-18. Usetweezers to gently loosen sponge filler from eyepiece assembly area. Lift cover from rangefinder.Remove sponge from cover by gently peeling it from adhesive.
Phillips Head Screw
Metal Mask Driver
Guide Screw
Detent Slot
Detent Spring
40
Figure 4-18. Removing cover from rangefinder assembly (model 600SE)
Removing Covers from Rangefinder Assembly (Model 600 Only)
Pry plate from eyepiece assembly area. Remove single screw, shown in Figure 4-19. Usetweezers to gently loosen sponge filler from eyepiece assembly area. Use tweezers to gently liftpaper cover from rangefinder casting. Lift cover assembly (paper and metal covers) fromrangefinder assembly. If necessary, peel paper cover from metal cover.
Figure 4-19. Removing cover from rangefinder assembly (model 600 only)
Plate
SpongeFiller
Screw
Eyepiece Assembly
RangefinderAssembly
Adhesivefor Plate
Adhesivefor Sponge
EyepieceAssembly
Plate
Cover
SpongeFiller
Screw
Adhesivefor Plate
Adhesiveon Metal Cover
RangefinderAssembly
PaperCover
MetalCover
Adhesiveon RangefinderCasting forPaper Cover
41
Removing Framing Mask Assembly (Model 600SE Only)
It is possible to remove and repair the framing mask spring (keeping the metal mask in tensionagainst the film framing mask) without disassembly of the rangefinder/viewfinder. Figure 4-20shows the spring. It is accessible after the viewfinder window cover and viewfinder windows havebeen removed (Figures 4-6 and 4-15). The viewfinder selector switch should be in the 127position.
Figure 4-20. Removing framing mask spring
Pull the spring end off the spring stud first. Then pull the spring off the screw. Replace spring.Apply fresh adhesive to window area before replacing screen and glass window.
The spring should be removed in a similar manner if the rangefinder assembly is removed fromthe camera as shown in Figure 4-21. Further disassembly down to the film mask assembly levelcan be done without readjustment.
Note: Removal of this framing screen (film mask) from the parallax frame (metal guide plate)will require realignment of the framing images and adjustment of the mask position.
Pull this end first.
Framing MaskSpring
42
Figure 4-21. Removing framing mask assembly (model 600SE)
Removing Framing Screen from Parallax Frame (Model 600SE)
The framing screen may be removed from the parallax frame by removing the upper left sidescrew and washer as shown in Figure 4-22. The other screws fit into a hole and two slots in thefilm. Gently lift the film over the pivot screw. Slide the film from the two right side screws; loosenthe screws only if film sticks to parallax frames.
Note: Removal of the film framing screen from the parallax frame will require realignment of theframing images and adjustment of the mask and framing screen positions.
Figure 4-22. Removing framing screen from parallax frame (model 600SE)
Rangefinder Assembly
Film Mask Assembly
Film Mask GuideScrews
Spring Stud
Metal MaskScrew
Framing MaskSpringShoulder
Screw
Metal Mask
Framing Screen
Parallax Frame
Parallax FrameScrew (2)
Screw Slot
Pivot Screw
Framing Screen Screw
Washer
43
Removing Framing Mask Assembly (Model 600) ( Figure 4-23)
Note: Removal of the film framing screen from the parallax frame will require realignment of theframing images and adjustment of the mask position.
Remove the top screw and slip the framing mask assembly up until the lower slot is free from thelower screw.
Figure 4-23. Removing framing mask assembly (model 600)
Removing Framing Screen from Parallax Frame (Model 600)
Remove the upper left screw and washer, as shown in Figure 4-24. The other screws fit into ahole and two slots in the film. Gently lift the film over the pivot screw. Gently peel film off tape.Slide the film away from the two right side screws. Loosen screws only if film sticks to the parallaxframe.
Figure 4-24. Removing framing screen from parallax frame (model 600)
RangefinderAssembly
Top Screw
Frame MaskAssembly
B
Parallax Frame
Pivot Screw
Framing Screen(Film Mask)
Screw (Upper Left Side)
Washer
Screw Slots
Tape
44
Removing Parallax Lever Assembly from Rangefinder ( Figure 4-25)
Remove the connector screw which holds the two levers together. Loosen and remove the shaftwhile holding the spring loaded lever assembly. Turn the rangefinder assembly over and removethe pivot screw holding the parallax lever (upper).
Figure 4-25. Removing parallax lever assembly from rangefinder assembly
Removing Objective Lens Assembly (Figure 4-26)
Remove four screws. Lift off objective lens assembly.
Figure 4-26. Removing objective lens assembly
Parallax Lever(Upper)
Washer
Pivot ScrewSpring
Parallax LeverAssembly Shaft
Screw(Connector)
At Reassembly, reset springtail against objective lens.
Shaft
Rangefinder Assembly
Screw (4)
Objective Lens Assembly
45
Removing Eyepiece Assembly (Figure 4-27)
The eyepiece ring can be screwed off to allow cleaning of the eyepiece concave lens. The plateis glued to the housing. Use a knife to lift an edge or corner. Insert a thin metal blade under theplate. Gently pry the plate free of the housing. Try not to bend or deform the plate. Slight bendscan be pressed flat in a smooth-jaw vise. Replace plate if permanently bent.
The four screws holding the eyepiece housing to the rangefinder assembly may have glue orepoxy on both the Phillips head and the threads. Use a sharp pick to remove glue from the crossslot. Use a carefully selected Phillips head screwdriver, with a blunt tip, flutes to fit the cross slotand a sturdy shank. Be careful not to strip the heads. Remove the four screws.Grip the eyepiece housing and pry it free.
The stepped spacer is glued to the assembly on the outer edge. When you pull this spacer out,the first convex lens will fall out, unless you are prepared to catch it. Reassemble the lenses andspacers as shown in Figure 4-27.
The mask is glued into the stepped spacer. It should not be necessary to pry out this mask unlessit is defective.
Reassembly will require removal of some glue from the plate. Apply Pliobond adhesive and pressthe plate into the mating recess on the rangefinder assembly.
Figure 4-27. Disassembly of eyepiece
Eyepiece Ring
Plate
Eyepiece Housing
Concave Lens
Convex Lenses
Stepped Spacer
Mask
Rangefinder Assembly
Spacer
46
Removing Mirror Assembly from Rangefinder Assembly (Figure 4-28)
Note: Removal of this assembly will require readjustment of the rangefinder (See Section 5).
The leaf spring position and the upper pivot position are fixed by shellac or other adhesive.Remove excess adhesive after removing parts. Cement these parts into a fixed position after therangefinder has been adjusted.
Remove nut. Hold mirror mount assembly and remove upper pivot. Jockey mirror mountassembly off the rangefinder assembly. Remove the three screws holding the mirror lever. Do notdisassemble the rangefinder assembly beyond the disassembly level shown in Figure 4-28.
Figure 4-28. Removing mirror assembly
Removing Decorative Cover from Front Panel (Figure 4-29)
Use a knife to pry up one corner of the cover. Insert a thin metal blade to separate the adhesiveholding cover to the front panel. The bent cover will need to be replaced. Remove excessadhesive before reassembly.
Figure 4-29. Removing decorative cover from front panel )model 600)
Screws
Leaf Spring
Mirror Mount AssemblyNut
Upper Pivot
Mirror Lever
RangefinderAssembly
Range Adjusting Screw(Infinity Setting)
Screw
Front Panel
Camera Body
Decorative Cover
47
Removing Inner Cover from Front Panel (Figure 4-30)
Remove six (6) Phillips head screws. Lift cover from front panel.
On the model 600SE camera, the lens release button assembly is part of the cover beingremoved. Do not remove the lens release button. It is not a listed spare part. Clean the contactsurface before reassembly. The locking lever and spring are attached to the front panel. Thebayonet must be removed before the locking lever can be removed.
Figure 4-30. Removing inner cover from front panel (model 600)
Removing 127MM Lens Assembly (Model 600) (Figure 4-31)
Remove covers as shown in Figures 4-29 and 4-30. Use Phillips screwdriver to remove sixscrews. Lift off lens. Note position of washers. Zero to three washers may be used at the lensmount.
For reassembly, reposition washers. Place he red line on the depth of field scale in the twelveo'clock position. Replace screws. Replace covers.
Removing Springs from Bayonet (Model 600SE) (Figure 4-32)
Remove covers as shown in Figures 4-29 and 4-30. Use Phillips screwdriver and remove twoscrews from one of the four springs. Use tweezers to grip the heel of the spring. Jockey thespring out of the slot in the bayonet. Remove remaining springs.
Reassemble by placing a spring into the slot in the bayonet and tightening the screws.
Model 600 Camera
Inner Cover
Screws (6)
48
Figure 4-31. Removing 127mm lens assembly from model 600 camera
Figure 4-32. Removing springs from bayonet
Model 600 Camera
Red Line on Depth ofField Scale (in TwelveO'Clock Position)
Washer (3)
127MM Lens Assembly
Screws (6)
Model 600SE Camera
Spring (4)
Heel End of Spring
Spring Slot (4)
BayonetScrew (8)
49
Removing Bayonet (Model 600SE) (Figure 4-33)
Remove covers as shown in Figures 4-29 and 4-30. Use Phillips screwdriver to remove sixscrews lift off bayonet. Note position of washers. Zero to three washers may be used at the lensmount.
Inspect stopper screw. Replace if damaged. Reassemble by repositioning washers. Placebayonet with stopper screw in four o'clock position. The locking lever tip should come through thebayonet. Tighten six (6) screws. Replace covers.
Figure 4-33. Removing bayonet from model 600SE camera
Removing Locking Lever from Front Panel (Model 600SE) ( Figure 4-34)
Remove bayonet as shown in Figure 4-33. Use Phillips screwdriver to remove two screws. Liftout lever. Remove spring
Reassemble by placing on stud. Place locking lever into recess area. The locking lever springfinger should be on top of the spring. Replace screws.
Model 600SE Camera
Locking Lever Tip
Stopper ScrewHole in the 4 O'clock
Position
Stopper Screw(Slot Head)
Slot for LockingLever TipBayonet
Screws (6)Phillips Head
Washer (3)
50
Figure 4-34. Removing locking lever from front panel of model 600SE camera
Removing Front Panel Leg (Figure 4-35)
The front panel leg may be removed at any camera assembly level.
Reassemble by observing fit relationship between boss on bottom of front panel leg and recess inbottom of front panel. Place boss in recess. Tighten screw.
Figure 4-35. Removing front panel leg
Recess Area
Locking LeverAssembly
Spring
Spring Finger
Locking LeverTip
Spring Stud
Model 600SECamera
Screw
51
Removing Front Panel ( Figure 4-36)
Remove covers as shown in Figures 4-29 and 4-30. The screws are glued in place. Select aproper fitting Phillips screwdriver to fit the screws in the deep holes in the front panel.
Remove eight (8) screws. Lift off front panel.
Figure 4-36. Removing front Panel
Removing Range Coupling Pin Assembly ( Figure 4-37)
Remove two (2) Phillips head screws. Lift off fixing plate. Pull out shaft. Shake out spring.Reassemble by inserting spring into socket from rear of front panel. Insert shaft. Position fixingplate and loosely attach both screws. Then tighten screws.
Figure 4-37. Removing range coupling pin assembly
Camera Body
Front Panel
Screws (6)
Deep Hole forScrews
Screws (2)
Fixing Plate
Shaft
Spring
Socket for Shaft(Range Coupling Pin)
52
Removing Flash Gun Bracket (Figure 4-38)
Remove two Phillips head screws. Remove bracket
Removing Leatherette and Plates from Camera Body (Figure 4-38)
The leatherette is a man-made material attached to a light metal backing. When removingleatherette, be sure to lift up from under the metal backing. Peel off the leatherette. Pry out plates.Replace bent parts.
Figure 4-38. Removing flash gun bracket and leatherette
Removing Tripod Socket (Figure 4-39)
The tripod socket can be removed from an assembled camera as shown in Figure 4-39. Use ablade to pry under the leatherette. The leatherette is made up of a man-made leather materialbonded to a metal disc. Be careful to insert blade under the light metal disc. Peel off theleatherette. If you separate the leather material from the disc, pry out the disc.
Use Phillips screwdriver; remove four flat head screws and tripod socket.
Reassemble as shown in Figure 4-39. Cement leatherette into socket.
PlateQSN11271
PlateQSN11351
BracketFlash Gun
ScrewPlate
QSN 11281
LeatheretteQSN11291
PlateQSN 11361
LeatheretteQSN11371
53
Figure 4-39. Removing tripod socket
Removing Sliding Locks ( Figure 4-40)
Carefully peel off the index mark plate. Use a knife to lift one end and slip a thin blade under theplate to break the glue joint. Remove excess adhesive before reassembly. Minor bends in theindex mark plate can be flattened in a vise. Badly bent plates should be replaced. Note positionof left and right plates.
Figure 4-40. Removing sliding locks
Camera Body(Removal of TripodSocket can occurwith cameraassembled.)
Tripod Socket
Screws (4)
Leatherette
Index MarkPlate (TYP.)
Open Lockat Bottom
Closed Lock atTop of Camera Hex Head Screws
Slide Lock (Left)
Index Mark Plate(Right)
Flat HeadScrews
Index Mark Plate(Left)
Guide Pin
Leaf SpringSlide Lock Cover
Slide Lock (Right)
54
Use a small Phillips screwdriver to remove two flat head screws from each slide lock cover.Remove the covers.
Remove the hex head screws, two each side. Remove leaf springs and slide locks. ApplyLubriplate before reassembly.
Note: Mark slide locks, left and right, for ease of reassembly.
Inspect guide pins. Remove and replace if necessary.
Reassemble as shown in Figure 4-40. Cement index mark plates into the slide covers. Theclosed lock symbol must be at the upper end as shown in Figure 4-40.
Removing Parallax Coupling Assembly (Figure 4-41)
Note: Removal of this assembly will require readjustment of the viewfinder (See Section 5).
Use a screwdriver with a 1/2" (1.3 cm) long thin blade. Remove the screw and lift out the parallaxrelay lever. The same screwdriver should be used to remove the hub. The parallax coupling levercan be pulled down inside the camera. The spring will fall free.
Figure 4-41. Removing parallax coupling assembly
Spring
Parallax CouplingAssembly
Front Panel
EccentricAdjustment
Range LeverAssembly
Coupling Pin
Parallax RelayLever
Screw
Hub
Camera Body
Spring
Parallax CouplingLever Assembly
55
Reassemble by placing spring on parallax coupling lever assembly. The position of the leversas you look up inside the camera is shown i the left side of Figure 4-41)
Removing Rang Lever Assembly (Figure 4-42)
Remove two (2) Phillips head screws from range lever upper. Carefully pull range lever upper offthe brass centering pin of the range lever assembly. Hold the range lever assembly inside thebody of the camera. Use screwdriver with a thin flat blade 1/2" (1.3 cm) long. Remove hub, rangelever assembly and washer.
Figure 4-42. Removing range lever assembly
Screws (2)Range Lever
Upper
Camera Body
Washer
Range LeverAssembly
56
Removing Range Lever Upper Spring (Figure 4-43)
Release spring so that both ends rest on back wall of camera body. Remove screw andspring.
Figure 4-43. Removing range lever upper spring
Removing Middle Lever (Figure 4-44)
Release spring. Use blade of screwdriver to remove middle lever shaft.
Note: Changing middle lever eccentric adjustment will require readjustment of VF/RFnear range setting.
Pull middle lever from shaft. Remove two Phillips head screws. Lift off base plate.
Removing Camera Body Sealing Sponges (Figure 4-45)
The back sealing sponge is accessible after film holder has been removed (Figure 4-1).Remove front panel as shown in Figure 4-36. The sponges are cemented in place. Use 1/8"(.33cm) chisel to scrape sponge and cement from groove; clean with trichloroethylenethoroughly before replacing sponges.
ParallaxRelay Lever
Range Lever Upper
Middle Lever
Back Wall
Screw
SpringBack Wall
Camera Body
CameraBody
Range LeverUpper Spring
57
Figure 4-44. Removing middle Lever
Figure 4-45. Removing camera body sponge
SpringMiddle Lever
Shaft
Middle LeverEccentric AdjustmentMiddle
Lever
Screws
Base Plate
Back SealingSponge
Camera Body
Front SealingSponge
58
Removing Strap Eyelets (Figure 4-46)
Use Phillips screwdriver to remove three (3) screws from each strap eyelet. Lift off strapeyelet. Remove adhesive and clean parts before reassembly.
Figure 4-46. Removing strap eyelets
Removing Flash Gun Mounting Socket (Figure 4-47)
Use Phillips screwdriver to remove four screws holding flash gun mounting socket to camerabody.
Figure 4-47. Removing flash gun mounting socket
Screws
StrapEyelet
Flash GunMounting Socket
Camera Body
Screws
59
Removing Grip Holding Socket (Figure 4-48)
Use a 2.5mm Allen wrench to remove three screws holding grip holder socket to camera body.
Figure 4-48. Removing grip holder socket
Removing Bottom Plates (Figure 4-49)
Use Phillips screwdriver to remove three screws from each bottom plate and lift off the plates. Pryout the two bosses. Remove excess adhesive from plates and clean parts before reassembly.
Figure 4-49. Removing bottom plates
Camera Body
Grip HolderSocket
Washers (3)
Screws (3)
Boss
Screws (6)
Right BottomPlate
Left BottomPlate
60
Removing PC Flash Connector Socket (Figure 4-50)
Use Phillips screwdriver to remove two screws holding PC flash connector socket to the lensassembly. Gently pull the free connecting wire away from the lens assembly with the connectorattached. Loosen slot head screw under the connector. Slide out the contact lug.
Figure 4-50. Removing PC flash connector socket
Removing Seiko 884 Shutter From 127MM and 150MM Lens(Figures 4-51 through 4-53)
Note: Any disassembly or adjustment of the lens system must be followed by lenscollimation check and RF/VF adjustment.
Release contact lug from PC flash connector socket as shown in Figure 4-50. Remove the lensassembly from the camera body, as previously described for model 600SE.
The shutter is held to the lens assembly by the retaining nut shown in Figure 4-51. The lensspanner wrench, special tool no. 12459 will reach the retaining nut through the model 600 camerabody.
Work on a clean soft surface. Use the lens spanner wrench special tool no. 12459 to reachthrough the rear of the lens assembly and screw off the retaining nut.
PC FlashConnector Socket
Screw
Contact Lug
ConnectingWire
Screws (2)
Mount forConnector Socket
Lens Assembly
61
Figure 4-51. Loosing shutter retaining nut with special tool no. 12459
Carefully lift the front end including the shutter away from the shutter cover assembly as shown infigure 4-52. The rear end of the lens barrel is not normally disassembled. Information ondisassembly is included only to cover urgent replacement of rusted, worn or deformed parts.
Note: Do not unscrew the internal parts of the helicoid assembly. It is very difficult toreengage the two pairs of left and right hand multi-lead threads within the helicoidassembly (Figure 4-53).
Grip the outside of the rear lens assembly, (Key No. 6, Figure 4-52) and screw out of the rear ofthe shutter. Screw the front lens assembly (Key No. 13) out of the front of the shutter. Clean andstore the lenses.
Note: When the aperture ring assembly is removed, the clock spring and steel ball(Key No's. 10 and 11) may pop out. Be prepared to capture these parts. Theball is located at the red mark on the index mark ring.
Use a thin blade screwdriver to loosen (not remove) three screws (Key No. 18). The plasticaperture ring (Key No. 12) is flexible to allow it to slip off a retaining washer (Key No. 19). Grip theaperture control knob (Key No. 17). Turn the aperture ring and it will slip off the index mark ringassembly. Remove screw (Key No. 16) holding aperture control knob (Key No. 17) to shutter.
Remove the index mark ring by removing the three screws and washers (Key Nos 18 and 19).Place the shutter with the front end facing up. Use two fingers to screw off a brass spanner nutholding the speed mark ring (Figure 4-53). Lift off speed mark ring.
Note: Do not turn the shutter over. Parts will fall out.
Replace spanner nut into shutter. The speed mark ring is part of the shutter assembly. Place
Special ToolNo. 12459
CouplingKey
Light BaffleNo. 2
Camera Body
Light BaffleNo. 3
Screw
Screw
Retaining Nut
Light BaffleNo. 1
Rear LensAssembly
Screw
62
shutter assembly in a plastic bag.
Figure 4-52. Disassembly of front end of 127MM and 150MM lens barrel
Figure 4-53. Removing speed mark ringDisassembly of 127MM Lens Barrel
Key No. Part Name
1 Shutter release Ring2 Shutter Cover Assembly3 Earth Plate4 Screw5 Spring6 Lens assembly, Rear7 Seiko Shutter8 Index Mark Ring9 Click Spring Holder10 Spring11 Steel Ball12 Aperture Ring #1713 Lens Assembly, Front14 Lens Cap15 Screw16 Screw17 Aperture Control Knob18 Screw19 Washer20 Tube21 Contact Lug
12
34 5
6
7
8
9
10 11 1213
14
1516
1718
19
2021
4
Retaining Nut
1 2 7 8 12
Aperture Blades
Shutter Blades
Front Lens LockRing
Time Mark Ring
Cross Section of FrontEnd of Lens Barrel 13
Note: Collimation of lens will be required after anydisassembly of lens system.
Front End of Lens Barrel(6 through 13)
ApertureRing
Index MarkRing
Spanner Nut
Screws (3) RetainingWashers (3)
ApertureControl Knob
Speed Ring
63
Disassemble front end as shown in Figures 4-51 through 4-53.
The assembly relationship of the rear of the lens barrel is shown in Figures 4-54 and 4-55. Thisdisassembly is normally not required.
Figure 4-54. Disassembly of rear of Lens barrel, 127MM lens
Screws (4)
Screws (3)
Light Baffle #3
Screws (3)
Screws (2)
Depth Field Scale Ring(Model 600)
Light Baffle #2
Light Baffle #1
Inner Tube
Coupling Pin
Coupling Key
Helicoid Assembly
Screws (3)
Set Screw (3)
Shutter CoverScrews (4)
Screw
Spring
ShutterRelease Ring
Rubber Grip
Focusing Ring
Helicoid Cover
Shoulder Screws (2)Washer
Plate
Screw (Plate)
Spring
Earth Plate
64
Figure 4-55. Disassembly of rear of Lens barrel, 127MM lens
The 127mm lens for the model 600SE is very similar to the 127mm lens for the model 600(Figures 4-54 and 4-55. Note the differences in the depth of field scale ring.
With the lens barrels removed from the camera and the shutter and front end removed from thelens barrel, you can remove screws and parts from both ends down to the helicoid assembly. Donot twist or force parts out of the barrel. It is easy to disassemble the helicoid assembly by anunfortunate twist of the lens barrel. A damaged (disassembled) helicoid assembly should not berepaired. It must be replaced, and it may be necessary to replace the lens barrel.
Access to the range coupling key assembly may be required to replace the spring or to lubricatethe slide plate with Molycote or Lubriplate. Remove four screws and lift out the light baffle No. 3.Remove three screws and lift the depth of field scale ring off the helicoid assembly ( Figure 4-55).The spring can be removed without loosening the shoulder screws or the plate screw. Lift one legof the spring off the shoulder screw. Hold spring, and lift off other leg. Unhook spring loop offplate screw.
Slip the rubber grip off the focusing ring. Turn the focusing ring to infinity. Note the lineup of theinfinity mark to the helicoid assembly. Soak in trichloroethylene and loosen the three tiny slottedset screws that were hidden by the rubber grip. Remove the four screws holding the shutter coverto the helicoid assembly. Remove the three screws from the helicoid cover. Remove the twoscrews holding the plate and washer to the helicoid assembly and the coupling key.Disassembly of 150MM Lens Barrel (Figure 4-56)
Plate
Spring
Screws (4)
Light Baffle #3
Screws (3)
Depth of Field Scale Ring(Model 600)
Screw (Plate)Spring
Plate
Washer
Coupling Pin
Coupling Key
Shoulder Screws (2)Heliciod Assembly
65
Disassemble front end as shown in Figure 4-52. The assembly relationship of the rear of the lensbarrel is shown in Figure 4-56. This disassembly is not normally required. If helicoid assembly isdefective, replace lens barrel. The light baffles are glued in position. Note position and mark lightbaffles 1 and 2 before disassembly. Remove rubber grip. Loosen four set screws and Phillipshead screw on focusing ring. Remove four screws holding shutter cover to the helicoid assembly.Slip off the shutter release ring and the focusing ring. Remove four screws holding helicoid coverto the helicoid assembly. Remove the three screws holding the depth of field scale ring to theinner tube. Remove five screws holding the inner tube to the helicoid assembly. Remove twoscrews holding the plate to the inner tube.
Figure 4-56. Disassembly of rear of Lens barrel, 150MM lensDisassembly of 75MM Lens ( Figures 4-57 through 4-62)
Spring
Light Baffle #3
Depth Field Scale Ring
Light Baffle #2
Light Baffle #1
Inner Tube
Coupling Pin
Coupling Key
Helicoid Assembly
Shutter Cover
Rubber Grip
Focusing Ring
Set Screws (4)
Pin
Rear Lens Cap
Screw
ShutterRelease Ring
Helicoid Cover
Screw
Spring
Earth Plate
Screw
Screws (3)
Screws (4)
66
Remove the front lens cap.
Turn the focusing ring to the close-up position. Grip the outer edge of the front lens assembly.Twist hard in a counterclockwise direction. Unscrew front lens assembly. Clean lens. Replacefront lens cap. Store lens.
Note: Any disassembly of the lens system will require collimation of the lens.
Figure 4-57. Front lens assembly, 75MM lens
Remove the PC flash connector socket and separate the contact lug as shown in Figure 4-50.Remove the rear lens cap (Figure 4-58).
Figure 4-58. Rear lens assembly, 75MM lensUse a strap wrench to loosen the rear lens assembly. Hold the lens barrel with the rear lens
Front Lens Assembly
Lens Identification Ring
Front Lens Cap
Rear Lens Cap
Rear Lens Assembly
Washer (Shim)
67
down. This will keep the shim washers and store for reassembly. Place the lens barrel with therear up, as shown in Figure 4-59. Use special tool No. CCR-12459 as a spanner wrench.Loosen the retaining nut holding the shutter to the lens barrel. Use your fingers to unscrew theretaining nut. Lift the lens barrel. The shutter assembly will be separated from the lens barrel.
Figure 4-59. Removing retaining nut from shutter, 75MM lens
Removing Aperture Ring and Index Mark Ring (Figure 4-60)
Lens BarrelBayonet
Tube
Shutter
Retaining Nut
Ring
Screws (4)
Lens Spanner Wrench(Special Tool No. CCR-12459)
68
Use a thin blade screwdriver to loosen (not remove) three screws holding the aperture ring to theshutter. Grip the aperture control knob. The flexible plastic aperture ring can be pulled off theretaining washers. The ring will still be retained by the knob.
Note: Be prepared to capture the click ring and steel ball. They are located at the redindex mark on the index mark ring.
Remove the two screws holding the knob to the aperture ring. Lift off the aperture ring. Removethe three screws and washers holding the index mark ring to the shutter.
Figure 4-60. Removing aperture ring and index mark ring
Removing Focusing Ring (Figure 4-61)
Contact LugClick Spring Holder
Spring
Ball Aperture Ring
RetainingWashers (3)
Screws (3)
Screw
Stopper Screw
ApertureControl Knob
Seiko Shutter 885
Index Mark Ring
Stopper Screw
Screw
69
Remove the rubber grip from the focusing ring. Loosen the four set screws that were hidden bythe rubber grip; it may require a long soak in trichloroethylene to dissolve glue in screw threads.Remove focusing ring.Remove four screws holding retaining ring to the depth of field scale ring.
Figure 4-61. Removing focusing ring
Removing 75MM Lens, Depth of Field Scale Ring (Figure 4-62)
Note: The helicoid assembly of the 75mm lens is inside the depth of field scale ring. Do not twist this assembly. The reverse, left and right hand, thread mechanism is easy todisengage and destroy.
Remove four screws holding shutter cover to the depth of field scale ring. Remove shutter coverand shutter release ring. Remove four screws holding the rings to the rear of the depth of fieldscale ring.
Depth of Field Scale Ring
Ring
Set Screws (4)
Screws (4)
Retaining Ring
Focusing RingRubber Grip
70
Figure 4-62. Removing 75MM lens, depth of field scale ring
Film Holder
Because of the simplicity of the Model 73 Film Holder, repairs are minimal. Those parts whichmay be replaced are: A) Mini-Roller Spread System; B) Adapter Plate; C) Bail Latch; D) CameraDoor Assembly.
A. Mini-Roller Spread System Disassembly/Reassembly
1. Following the instructions printed on the inside of the door assembly, lift out thespread system.
2. Refer to Figure 4-63. Insert special tool No. 11606 between the two sides of either loadspring at the location shown.
3. Rotate the handle of the tool to spread the arms of the spring as far apart as the tool willallow.
4. Grasping both the spring and the tool, slide the spring out of the plastic frame in thedirection of the arrow (Figure 4-63).
Ring
Ring
Screws (4)
Screws (4)
Shutter Release Ring
Shutter Cover
Depth of Field Scale Ring
Plates (2)
Earth Plate
Screw
Spring
71
Figure 4-63. Removing spread system springs
5. Repeat the procedure for the other spring.
Note: Before withdrawing the rollers, note that the plastic bearing blocks that support the ends of the rollers are dissimilar in both color and configuration.Observe and note where each is located. Reassemble in sameposition (Figure 4-64).
Figure 4-64. Roller Bearing Blocks
6. The rollers are supported by plastic bearing blocks which slide in dovetails in the
BSpread
Pull
Rotate
Tool No. 11606
Left Side (White)
Right Side (Yellow)
72
platform. The blocks and rollers must be pulled straight up and out of the grooves.Do not cock the rollers while withdrawing the assembly.
Note: Although it may not be necessary to replace both rollers, it is necessary toreplace the pair of rollers as an assembly.
CAUTION
Do not reinstall a bearing block that is cracked or broken.
7. Install the bearing blocks on the rollers.
8. Refer to Figure 4-65. Slide the roller assembly into the dovetail grooves in the platform.
9. Using special tool 11606, spread one of the load springs and, holding the tool and springtogether, slide the spring into the platform. The spring must slide between the innersurface of the platform and the plastic projection marked A on Figure 4-65.
Figure 4-65. Mini-roller spread system
B
A
D
Bearing BlockLeft side (White)
Load Spring
Rollers
Bearing BlockRight Side (White)
Load Spring
Platform
Edge Control Spring
Edge Control Bar
C
73
10.Slide the spring in until the end bottoms in the cutout provided for it in the top of thebearing block. See B on Figure 4-63.
11.Remove the special tool.
12. Install the other load spring in the same manner.
13.Using tweezers, lift the ends of the edge control springs onto of the holes in the platform.
14.Using long-nose pliers, squeeze the slotted projection of the edge control bar (C and D)on Figure 4-65 until the bar can be drawn free of the platform. The spring will be released.
15.To replace the components, place the spring in position on the platform.
16. Place the edge control in position and press the center of the bar until the projections(C and D) lock into the center hold.
B. Adapter Frame - Disassembly/Reassembly
Note: Refer to Figure 4-66 to identify items called out below in parentheses.
1. Remove and retain eight screws (3) holding the adapter frame (2) to the film pack holderpart of the camera door assembly. The adapter frame is now free. Remove and retain thelight seal (6), spring (5) and sponge (4).
Note: Before reassembling the film holder, examine the metal adapter frame andthe plastic film pack holder. Check that the mating surfaces are flat. If either partis warped or bowed, replace it. Misalignment of these mating surfaces can causethe film to be out of focus.
2. Align the adapter frame to the film pack holder. Replace the dark slide light seal (6),spring (5) and sponge (4). Place the dark slide into the green recess on the adapterframe (2).
3. Secure the adapter frame (2), using the eight screws previously removed and retained.
4. Pull the dark slide. Be sure it works smoothly.
5. Test for light leaks:
a. Load a pack of 107 film into the film holder.
b. Be sure that the dark slide and door are fully closed and pull the safety cover from the pack.
c. Using bright 150 watt lamp, "paint" the film holder with light for one minute, three feetfrom film holder.
74
d. Pull a sample film.
e. If any light leak is found, locate its source and repair the film holder as necessary.
C. Bail Latch - Disassembly/Reassembly
1. The bail latch may be removed by gently spreading it at the door busings and pulling it free.
2. Replace the bail latch by inserting one end in the door busings and "popping" the otherend in the opposite bushing.
D. Film Holder Door - Disassembly/Reassembly (Figure 4-66)
1. Remove the mini-rollers and adapter frame as instructed.
2. Spread the pivot end of the door to free it from the film pack holder, and remove the door.
3. Install the door by spreading the pivot end and carefully slipping it onto the pivots.The door will snap into place.
4. Replace the adapter frame and A-11 mini-rollers as instructed.
5. Test for light leaks as previously instructed.
Figure 4-66. Film holder parts
Bail LatchA-11 Mini-RollerSpread System
(1)Camera Door
Film PackHolder
(4)Light Seal, Felt
(6)Light Seal
Dark SlideAssembly
(3)Screw
(2)Adapter Frame
(5)Spring
75
5 - Testing and AdjustmentsTable 5-1 lists the tests that are necessary in the repair of Model 600/600SE cameras:
Table 5-1. Model 600/600SE Camera Tests
Test Equipment Used Camera Adjustments
Light Leak Test 150W Lamp, Replace Light Seals.3000 ASA Film Type 107.
Shutter Speed Test Shutter Speed Tester. Repair or Replace Shutter.
RF/VF Parallax andLens Collimation Collimator RF/VF Topside Adjustment,Tests:• Topside Tripod, RF/VF Infinity-Range Adjustment,
• Infinity-Tube Tracking Focal Plane Plate, RFVF Near-Distance EccentricAdjustment,
• Aiming and Framing Reporter Aiming and Lens Barrel Coupling PinFraming, Adjustment,
• Near-Distance Tracking Aiming Circle. Front Lens Position Adjustment.
Light Leak Test
1. Prepare the camera to take a picture. Mount film holder with dark slide onto the camera body.Load a 3000 speed (Type 107) film pack into film holder. Do not cock or release shutter.
2. Illuminate camera all around for one minute, with light from a 150 Watt lamp no closer thanthree (3) feet from the camera. Do not shine light directly into the exit door.
3. Remove unexposed film in normal manner, as if you had just taken a picture. Inspect film forlight leaks. Check that results are not due to old or defective film pack.
4. Remove dark slide. Again, illuminate camera with light for one minute. This time, concentrateon area around slot for dark slide. Remove second unexposed film frame.
5. Both frames should be totally black. If any spots, lines, or fogging are observed on the film,attempt to isolate leak area, by substitution of film holder or lens and/or covering suspectedarea with opaque black tape.
76
6. Compare the accented and masked light leak photographs to confirm location of light leak.Replace faulty light seal, as described in Section 4.
7. After replacement of light seal, repeat test. Compare film frames. Repeat until all light leakshave been isolated and eliminated.
Shutter speed Test
1. Remove the film holder and place the camera on a commercially available mechanical shutterspeed teste that can read shutter speeds in seconds and fractions of seconds. (Limitedclearance on some testers may require removal of the lens barrel from the camera, orremoval of the shutter from the lens barrel.)
2. Open the shutter to the widest aperture setting, f/4.7 stop or the f/5.6 stop. Trip and test theshutter through all the speed settings from 1 second to 1/500 second.
Note: Table 5-2 shows the allowable range of shutter speeds that are accepted by PolaroidCorporation.
Table 5-2. Allowable Range of Shutter Speeds
Shutter Speed Speed Desired Time Allowable Time (Milliseconds) Setting (Seconds) (Milliseconds) Minimum Maximum
1 1 1000 800 12002 1/2 500 400 6004 1/4 250 200 3008 1/8 125 100 15015 1/15 66.7 53.3 8030 1/30 33.3 26.6 4060 1/60 16.7 13.3 20125 1/125 8 5.6 10.4250 1/250 4 2.8 5.2500 1/500 2 1.4 2.6
3. If any of the above speeds are not met within its allowable range, the shutter must bereplaced. Shutter repair is not covered in this manual. Shutter removal is covered inSection 4 and in videotape training instructions.
77
RF/VF Parallax and Lens Collimation Tests
The purpose of parallax and collimation tests is to assure that near and infinity images seenthrough the camera can be focused onto film loaded into the camera. Therefore, you mustmeasure how closely "the rangefinder image coincidence" tracks " the lens sharpest focus", asdescribed in the following procedures; Infinity-Tube Tracking Test, and Near-Distance TrackingTest.
The interchangeable lenses of the Model 600SE camera have different rangefinder trackingdiscrepancy allowances. All three lenses (75mm, 127mm, and 150mm) should be tested beforedecisions about adjustments are made.
Collimation and parallax tests are subject to error due to the observer's eyesight and sightingability. A second observer should confirm results before major adjustments are made.
Topside Test
1. Plug in the power cord of collimator No. 11431 to a 110 vac electric outlet. Turn the line switchto ON. Turn the function switch to INF (infinity) .
2. Mount a camera on a tripod. Position it in front of the collimator as shown in Figure 5-1.
Figure 5-1. Camera setup for infinity-tube test
Infinity Tube
Tripod
Collimator
78
3. Look through the viewfinder eyepiece. Aim the camera at the collimator infinity tube. Turn thelens focus ring to infinity. The image you should see is shown in Figure 5-2. The image isinverted and slanted. If the image shown in Figure 5-2 cannot be seen clearly through theviewfinder, move the camera. Adjust aiming until a clear images obtained. It may benecessary to raise the tripod or move it left or right.
Figure 5-2. Perfect image of infinity target seen through the viewfinder at infinity
4. Move the lens focusing ring away from the infinity stop. Two images should be seen throughthe viewfinder eyepiece ( Figure 5-3). Turn the lens focus ring to get perfect imagecoincidence. (This may not be the infinity stop position.)
Figure 5-3. Split image seen through viewfinder
Topside discrepancylimit is width of base line.
Base Line
79
5. If the base lines do not line up, remove rangefinder top cover and make any necessary topsideadjustment (Figure 5-4). If necessary, use trichloroethylene to free topside adjusting screw.Turn topside adjusting screw only. Observe movement of infinity-tube-target image through theviewfinder eyepiece. Adjust until base lines line up as shown in Figure 5-2. The base linesmust butt each other to be within allowable limits. Replace top cover.
Figure 5-4. Location of topside adjusting screw
Infinity Tube Tracking Test
1. Completing the topside the test Steps 1 through 5 prepares the RF/VF for this test.
2. Sight through the RF/VF eyepiece. Focus to get perfect image coincidence. Mark with apencil the location of perfect image coincidence on the distance scale of each lens as shownin Figure 5-5.
Figure 5-5. Marking image coincidence at infinity
Topside Adjusting ScrewSpring
Rangefinder
Image Coincidence
80
3. Focus the loupe on focal plane plate No. CCR-12262. The focal plane plate has a flat glasssurface. When this plate is loaded into the film holder on the camera, this glass surface isaccurately located at the focal plane of the camera. The loupe on the plate allows you to see amagnification of an image focused through the camera lens onto this focal plane surface.Use a scribe mark on the glass surface to focus the loupe to your eye. Each observer will haveto focus the loupe individually. Seek the maximum contrast between the dark area of thescribe mark and the brightness of the background. When the sharpest image of the scribemark on the focal plane is obtained, lock the loupe eyepiece with the locknut.
4. Set the camera for collimation test, as follows:
a. Remove the lens cap.
Note: Be sure the camera lens is clean before the camera is collimated.
b. Remove dark slide from film holder. Open door on film holder.
c. Place the focal plane plate No. CCR-12262 into the film holder as if it were a film pack(Figure 5-1). Check that the plate is fully seated to the right.
d. Set the aperture to the smallest number (largest opening).
Aperture127mm lens = f/4.7150mm lens = f/5.675mm lens = f/5.6
e. Set the shutter to "B" (bulb).
f. Cock the shutter.
g. Trip and tape the shutter release depressed into the hand grip to keep the shutter open.
5. Measure Collimation Tracking Error at Infinity, for each lens.
a. Sight through the focal plane loupe at infinity tube target. Aiming of the camera from thisparallax test should be adequate. Make focusing correction, if required, so that 40mmgrid is seen clearly, as shown in Figure 5-6.
b. Obtain the sharpest focus of infinity tube target image through each lens. Mark this locationon the distance scale of each lens, as shown in Figure 5-7.
81
Figure 5-6. Infinity-tube as seen through focal plane loupe
Figure 5-7. Measuring collimation tracking error at infinity
c. Measure tracking error by using a ruler or other measuring device to measure gap;Xbetween marks on the distance scale of each lens. Tracking error = " X ", cannotexceed the following limits:
Lens Xmax Xmax
127mm 0.039 inches (1/32) 1mm150mm 0.078 inches (5/64) 2mm 75mm 0.090 inches (3/32) 2.3mm
Best Loupe Focus Image Coincidence
X
82
d. Correcting Tracking: If error exceeds these limits, an adjustment is required. However,perform aiming and framing target tests before making adjustment. Also verify any grossdiscrepancies before adjusting. Leave pencil marks on the distance scale, so infinitytracking error can be compared to near distance tracking error.
Before making an adjustment to the Model 600SE camera, you must compare thecollimation tracking error measured sighting through each interchangeable lens. Thiscomparison will avoid needless adjusting back and forth of the three lenses and viewfinder.In most instances, a single adjustment of the infinity range screw will be sufficient to bringthe tracking discrepancies of all three lenses within allowable limits.
Aiming and Framing Target Test
1. Mount the reporter aiming and framing target No. ECR-12261, on a wall, as shown inFigure 5-8.
Figure 5-8. Reporter aiming and framing target
2. Mount a vertical strip of black tape 3/4 inch (2cm) wide by 6 inches (16cm) long to the target,above the center square.
Find the center of the framing target. (Use long straight edge or stretch string across thediagonals of the inside of the framing rectangle, to find center.) Use a tack to mount theaiming circle ACR-12438 at the center of the target.
3. Move tripod a couple of inches from the target. Adjust and lock height of tripod so that thecenter of the lens is at same height as the center of the aiming circle Figure 5-9).
Black Tape
83
Figure 5-9. Camera lined up with aiming circle
4. Remove tape from shutter release. Remove focal plane plate from film holder. Load a 107 or108 film pack. Remove film pack dark slide.
5. Move the tripod back from the target, as follows:
Lens Suggested Distance
127mm 80.5 inches (2 meters)150mm 96 inches (2.5 meters)75mm 44 inches (1.2 meters)
Note: The same suggested distances apply to the near-distance tracking error testprocedure. On the Model 600SE camera, complete tests on a single lens at thesuggested tripod position., Then move tripod to next position and complete testsfor the additional lenses.
6. Look through the viewfinder eyepiece. Try to position the camera so that the albada lineslineup with the target framing lines as shown in Figure 5-10.
View each corner separately. Make sure the albada lines are between the target lines andare spaced evenly left to right.
a. Test 127mm lens first. Move viewfinder selector switch to the 127 position.
b. When testing the 150mm lens make sure the 150 position is set by the viewfinder selectorswitch.
84
Figure 5-10. Line up albada line with framing target
c. Framing for the 75mm lens is done by sighting through the 75mm accessory viewfinder, asshown in Figure 5-11.
Figure 5-11. Sighting for parallax Test for 75mm Lens
7. Set the aperture and shutter speed to suit film speed and available light. Cock and releaseshutter, to take a picture of the target.
Scribe cross lines from the outside corners of the picture as shown in Figure 5-12.The intersection of the scribe lines must be within the aiming circle.
The intersection of the scribe lines must be within the aiming circle.
Viewfinder Albada Lines
Target
Sight through 75mmAccessory Viewfinderfor Framing Only
75mm Lens Assembly
Sight through CameraEyepiece for CoincidentImage Tests
85
Figure 5-12. Aiming measurement
8. If the intersection is outside the aiming circle, adjust the position of the viewfinder.
Note: Do not correct aiming errors by adjusting the position of the lens assembly.
a. Adjust the 127mm and 150mm aiming errors to the left and right by shifting the left-to-rightposition of the rangefinder/viewfinder. Figure 5-13 shows the location of the three brassscrews which secure the viewfinder to the body of the camera. Remove top cover.Loosen the screws, only enough to shift the RF/VF position.
b. Up-and-down 127mm and 150mm aiming errors can be adjusted by placing a small shimunder the viewfinder assembly.
Figure 5-13. Preparation for aiming adjustment
Brass Screw
Brass Screw
Brass Screw
86
c. The aiming of the 75mm accessory viewfinder can be adjusted left or right by loosening thescrews securing the accessory shoe ( Figure 5-14). Shift position of accessory shoe.
Figure 5-14. Adjusting aiming of the 75mm accessory viewfinderby repositioning accessory shoe
d. Up-and-down 75mm aiming can be adjusted two ways (Figure 5-15). First check that thedistance scale on the accessory viewfinder agrees with the measured distance to thetarget. If in error, adjust distance scale to agree with measured distance. Use spannerwrench with pencil point tips to loosen lock-screw.
Figure 5-15. Adjusting distance scale on 75mm accessory viewfinder
Stopper Screw
Shoe Cover
Screws (4)Accessory Shoe
Cover
Holder Plate
Accessory WideAngle Viewfinder
Lock ScrewDistance Scale
87
Turn distance scale with your finger, until scale reading agrees with measured distance.Tighten lockscrew. If additional adjustment is required, insert shim under mounting baseas shown in Figure 5-16.
Figure 5-16. Shim adjustment to 75mm accessory viewfinder
e. Take an aiming photograph as previously described. Scribe lines and determine if errorhas been corrected, as shown in Figure 5-12.
Near Distance Tracking Test
1. Mount the camera on a tripod at the same distance as used in the aiming and framing tests(Figure 5-17).
Lens Suggested Distance
127mm 80.5 inches (2 meters)150mm 96 inches (2.5 meters)75mm 44 inches (1.2 meters)
2. Look through the RF/VF eyepiece. Adjust the lens barrel focusing ring to obtain perfectcoincidence of the vertical tape at the center of The Reporter aiming and framing targetNo. ECR-12261. Mark with a pencil the distance scale of each lens as shown in Figure 5-18.
Note: Do not move tripod or camera, until collimation test is completed.
Shim Location
Plate
Mounting Base
88
Figure 17. Camera setup for near distance collimation test
Figure 18. Marking image coincidence at near distance
3. Set the camera as follows, for collimation test. The camera and tripod position should not bechanged from the image coincidence position.
a. Remove the lens cap.
Note: Be sure the camera lens is clean before the camera is collimated.
b. Remove dark slide from the film holder. Open door on film holder.
Focal Plane Plate
Film Holder
Door Open Seat Plateto Right
Tripod
Focal Plane Loupe
Image Coincidence
89
c. Place the focal plane plate No. CRR-12262 into the film holder as if it were a film pack(Figure 5-17). Check that plate is seated to the right. Obtain sharp focus of the scratch onthe focal plane.
d. Set the aperture to the smallest number (largest opening).
Aperture127mm lens = f/4.7150mm lens = f/5.675mm lens = f/5.6
e. Set the shutter to "B" (bulb).
f. Cock the shutter.
g. Trip and tape the shutter release into the hand grip to keep the shutter open.
4. Measure collimation tracking error at near distance for each lens.
a. Sight through the focal plane loupe and aim camera at the tape on The Reporter aimingand framing target.
b. Obtain sharpest focus of each lens of the tape target image through the focal plane loupe.Mark with a pencil this location on the distance scale of each lens, as shown inFigure 5-19.
Figure 5-19. Measuring collimation tracking error at near distance
Best Loupe Focus Image Coincidence
X
90
c. Measure tracking error by using a ruler or other measuring device to measure gap: X,between marks on the distance scale.
Tracking error = X, cannot exceed the following limits:
Lens X Max X Max
127mm 0.039 inches (1/32 1 mm150mm 0.078 inches (5/64) 2 mm75mm 0.090 inches (3/32 2.3mm
5. Make tracking discrepancy adjustments.
a. If tracking discrepancy exceeds the set limits, an adjustment is required. Verify any grossdiscrepancies. Verification should be done by a second observer.
b. On the Model 600SE, comparison of the results of the tracking error measurements foreach of the three lenses should be made, in order to determine which adjustment to make.
c. Make the following parallax adjustments listed in Table 5-3 to correct tracking errors. Thenretest to assure elimination of tracking error from each of the three lenses.
Table 5-3. Parallax Adjustments
Adjustment Comment
RF/VF Infinity This is the preferred adjustment; it is easily accessible andRange (Screw) provides the widest range of adjustments (Figure 5-20).
RF/VF Near Distance Use for near distance fine adjustment only. Use only if error(Eccentric Screw) is not resolvable by infinity range adjustment and near
distance tracking error is larger than infinity error.
This is normally a factory setting (Figure 5-21)
Lens Barrel Coupling Use for gross error in one of the interchangeable lensesPin (Screw) of Model 600SE camera ( Figure 5-22). Adjust until
tracking error is within allowable discrepancy limits.
91
Figure 5-20. Access to infinity range adjustment
Figure 5-21. RF/VF near-distance eccentric screw adjustment
Figure 5-22. Location of lens barrel coupling pin adjustment
Coupling PinAdjustment Screw
(Rear of Lens Barrel)
Access Hole
92
6. Lens collimation adjustment. If the adjustments described in Step 5 will not bring the trackingdiscrepancy to within the limits listed in Step 4, adjust the position of the front lens.
a. Use a lens spanner wrench to loosen the front lens lock ring (Figure 5-23). Put a fewdrops of trichloroethylene around the outside of the front lens lock ring. Let it soak into thethreads a few minutes. Break the shellac bond and free the front element.
b. Set the lens into a camera mounted on a tripod in front of the collimator, as shown inFigure 5-1. Turn the lens bezel to the infinity stop position.
Set the collimator switch to infinity.
Cock the shutter. Trip and tape the shutter release to keep the lens open.
c. While looking through the lens adapter loupe, slowly turn the lens until the 40 lines/mm isclear. Stop turning when you see the 40 lines/mm sharpest.
Figure 5-23. Loosening front lens lock ring
93
d. Move the camera to the aiming and framing target as shown in Figure 5-10.Look through the viewfinder eyepiece. Adjust focus until the images of the tape linecoincide. Mark the distance scale.
e. Look through the focal plane loupe. Slowly adjust the lens until the sharpest image is seen.Mark the distance scale.
f. Measure the tracking discrepancy at near distance by using a ruler or other measuringdevice to measure gap between marks (d. and e. above) on distance scale. Thediscrepancy cannot exceed limits listed in Step 4. Adjust lens to reduce error.
g. Return to the infinity tube and move the focus back to infinity. The minimum reading mustbe 40 lines/mm.
h. When the image seen through the lens loupe is sharp at both infinity and near distanceposition, lock the front lens lock ring.
Secure the front lens to the mount by applying three drops of shellac at equidistant pointsaround the lens. DO NOT DRIP SHELLAC ONTO THE LENS.
7. Perform any necessary rangefinder/viewfinder adjustments, after this lens collimation has beencompleted.
94
6 - Special Tools and Test Equipment
The special tools listed in Table 6-1 are used to repair the model 600/600SE cameras.
Table 6-1. Special Tools and Test Equipment
Name Tool Number
Collimator 11431Focal Plane Plate CCR-12262Reporter Aiming and ECR-12261Framing TargetAiming Circle ACR-12438Spanner Wrench CCR-12459Spreader for Mini-Roller 11606
Figure 6-1. Collimator and focal Plate
AC Power CordPlugs into
110 VAC Outlet
Infinity Tube
Collimator
Focal PlanePlate
95
Figure 6-2. Test targets
Figure 6-3. Special tools
Reporter Aiming and Framing Target Aiming Circle
ModifiedSpanner Wrench
(No. W6600)
ModifiedStraight Blade End Tips
(No. T3790)
Standard Straight PencilPoint Tips(No. T3785)
SpreaderFor Mini-Roller
(No. 11606)