Predicting Creep Crack Initiation in Austenitic and Ferritic Steels using the Creep Toughness Parameter and Time Dependent Failure Assessment Diagram
Catrin M. Davies
Department of Mechanical Engineering, Imperial College London, South Kensington
Campus, London SW7 2AZ. Abstract
Methods for evaluating the creep toughness parameter, mat
cK , are reviewed and mat
cK data are determined for a ferritic P22 steel from CCG tests on compact tension,
C(T), specimens of homogenous parent material (PM) and heterogeneous specimen
weldments at 565 ° C and compared to similar tests on austenitic 316H stainless
steel at 550 °C. Appropriate relations describing the time dependency of mat
cK are
determined accounting for data scatter. Considerable differences are observed in the
form of the mat
cK data and the time dependent failure assessment diagrams
(TDFADs) for both the 316H and P22 steel. The TDFAD for P22 shows a strong time
dependency but is insensitive to time for 316H. Creep crack initiation (CCI) times
predictions are obtained using the TDFAD approach and compared to experimental
results from C(T) specimens and feature components. The TDFAD based on PM
properties can be used to obtain conservative prediction of the CCI on the weldments.
Conservative predictions are almost always obtained when lower bound mat
cK values
are employed. Long term test are generally more relevant to industrial component
lifetimes. The different trends between long and short term CCI time and growth data
indicate that further long term test are required to further validate the procedure to
predict the lifetimes of high temperature component lifetimes.
Keywords TDFAD, Creep Toughness, Creep Crack Initiation (CCI), 316H Steel, P22 Steel, Weldments. Nomenclature
a, a = Crack length, Crack extension
a = Crack growth rate
A = Creep strain rate coefficient
Ap = Primary creep strain coefficient
Bn = Specimen net section thickness between side-grooves
Br = Coefficient in the stress rupture time law
C* = Steady state creep characterising fracture mechanics parameter
CCG = Creep crack growth CCI = Creep crack initiation
D = Constant coefficient in creep crack growth rate correlation with C*
Di = Constant coefficient in creep crack initiation time correlation with C*
E = Elastic (Young’s) modulus
E′ = Effective elastic modulus
H = Correlating coefficient in the cmatK vs. time relation
HAZ = Heat affected zone
J = Elastic-Plastic fracture mechanics parameter
j = The power-law exponent in the cmatK vs. time relation
JIC = Material Mode I plane strain elastic-plastic fracture toughness
K = Linear-Elastic stress intensity factor
KIC = Material Mode I plane strain fracture toughness
Kr = TDFAD parameter measuring proximity to fracture cmatK = Creep toughness parameter
LB = Lower bound
Lr = TDFAD parameter measuring proximity to plastic collapse or creep rupture
Lrmax
= Maximum value of Lr at the cut-off point in TDFAD
n = Creep stress exponent
np = Primary creep stress exponent
P = Load
p = Primary creep parameter
PLC = Plastic collapse load of cracked body
PM = Parent material ROA = Reduction of area
t, Δt = Time, time increment
ti = Creep crack initiation time
tiExp
= Experimentally measured creep crack initiation time
tiPredicted
= Predicted value of the creep crack initiation time
UB = Upper bound
pU = Area under the load displacement curve associated with plasticity
v = Poisson ratio
vr = Rupture stress exponent
W = Specimen width
WM = Weldment c = Load line displacement associated with creep
ε c = Strain component associated with creep deformation
ε e = Strain component associated with elastic deformation
ε pl
= Strain component associated with plastic deformation
ε total
= Total strain
εf = Plastic ductility cf = Creep failure strain (creep ductility)
ref = Total strain at reference stress
e
ref = Strain at reference stress associated with elastic deformation
p
ref = Strain at reference stress associated with plastic deformation
c
ref = Strain at reference stress associated with creep deformation
cp ,
cs = Primary and secondary creep strain increments
i = Exponent in correlation of initiation time with C*
= Exponent in correlation of creep crack growth rate with C*
= Factor relating J/C* to the plastic/creep area under a load
displacement curve
0.2 = 0.2% proof strength
UTS = Ultimate tensile stress
σ0.2 = 0.2% proof stress of the material
c2.0 = 0.2% creep strength (stress at 0.2 % inelastic strain)
σflow = Flow stress 0.2 2UTS
1 Introduction
The lifetime of components operating in high temperature plant is limited by the
mechanisms of creep crack initiation (CCI) and growth (CCG). The CCI time is the
period of time prior to the onset of crack extension from an existing defect due to
creep crack growth and can occupy large fraction (> 80%) of a components service
lifetime 1. The CCI time is generally defined as the time for a defined small
measureable crack extension, typically 0.2 mm for laboratory specimens or 0.5 mm 2.
Reliable predictions of CCI time are fundamental in high temperature component
lifetime assessments due to the duration of the CCI period.
The time dependant failure assessment diagram (TDFAD) approach has become
increasingly recognised for the prediction of creep crack initiation (CCI) times 3. The
development of the TDFAD has mainly been based on austenitic type 316H stainless
steel which differs from ferritic steels in their tensile and creep material behaviour and
further verification are required before the procedure may be recommended for
ferritic steels 4, 5. Two widely used alloys for high-temperature plant components with
contrasting properties are ferritic P22 (2¼Cr1Mo) steel and austenitic type 316H
stainless steel. The favourable qualities of these steels include high creep ductility
and relatively high weldability 6, 7. These two steels are considered here in the
evaluation of the TDFAD method.
The TDFAD approach for CCI time predictions relies on the availability of reliable
creep toughness (cmatK ) data. The main advantage of the TDFAD approach is that
detailed calculations of crack tip parameters such as C* are not required and that the
TDFAD can indicate whether failure is controlled by crack growth, creep rupture or
plastic collapse i.e. the fracture regime need not be specified in advance. Methods
for evaluation or estimating the cmatK parameter have been developed and modified
over recent years.
A considerable amount of creep toughness data has been determined for
austenitic type 316H stainless steel in the region of 500–700° C, though mainly at
550° C 8, 9. Limited cmatK data have also been determined for a range of ferritic steels
4, 5, 8, 10-12, and in some cases TDFADs have also been produced. Creep toughness
data often show appreciable scatter 8, 9 which must be considered when obtaining
CCI time predictions. In the majority of cases, where TDFADs have been determined
together with creep toughness data, explicit CCI times have not been obtained.
Generally, the CCI data for a given crack extension have been plotted on a TDFAD
for a range of times and an assessment made to determine if the TDFAD approach
leads to conservative predictions, or sometimes a range of CCI times indicated. The
degree of conservatism/non-conservatism however, is not indicated.
Considerably high loads are often applied to specimens in CCG tests, leading to
relatively short test durations compared to the lifetimes of high temperature
components operating in plants. Therefore, the application of methods based on
CCG test data to predict real component lifetimes require validation 4. Components
are often welded and the application of the TDFAD approach for weldments has
been considered 12-16. However, a number of complications arise when considering
weldments such as material mis-match effects which may require consideration.
In previous work 9, the TDFAD approach has been applied to predict CCI times in
austenitic type 316H stainless steel at 550° C, and the sensitivity of predictions to
creep toughness data bounds and reference stress solutions have been examined.
In this work methods for cmatK evaluation and estimation are reviewed and
cmatK data
are determined for a ferritic P22 steel from CCG tests on compact tension, C(T),
specimens of homogenous parent material and heterogeneous specimen weldments
at 565 °C. The weldments consist of parent material (PM), weld metal and a heat
affected above (HAZ). The crack tip is located on the HAZ/PM boundary where
cracking is often observed in practice. Appropriate relations describing the time
dependency of cmatK are determined accounting for data scatter. The TDFAD
diagram and its associated parameters are then compared for the austenitic type
316H and ferritic P22 steel. The influence of test duration, and material condition are
also considered and CCI time predictions obtained and compared to experimental
results from short and long term laboratory tests specimens and feature components.
2 The Failure Assessment Diagram (FAD) Approach
The FAD procedure considers that failure will occur by plastic collapse or
brittle/ductile fracture. The proximity to failure by fracture and plastic collapse are
measured by the parameters Kr and Lr , respectively, defined by
12 2
r
IC IC
K KK
K E J
(1)
0.2
ref
r
LC
PL
P
(2)
where KIC and JIC are fracture toughness values (critical values of K and J for
fracture under Mode I, tensile loading), E′ the effective elastic modulus (equal to E for
plane stress or E/(1 - v2) for plane strain conditions where v is the Poisson ratio). In
Eqn (2) σref is the reference stress 1 of a geometry, 0.2 is the 0.2% proof stress
(measure of the materials yield stress), P the applied load and PLC the collapse load
of the cracked geometry 1.
The R6 Option 1 curve 17, 18 is material independent and defined by
2 61 0.14 0.3 0.7exp 0.65r r rK L L
for Lr ≤ Lrmax (3)
Kr = 0 for Lr > Lrmax
(4)
The cut-off, Lrmax
, which indicates failure by plastic collapse is defined by the ratio
max
0.2
flow
rL
(5)
where σflow is the mean of the ultimate tensile stress, UTS, obtained from the
engineering stress-strain curve and the 0.2% proof stress i.e. 0.2 2flow UTS
The R6 Option 2 FAD has a material specific failure assessment curve (FAC)
which has been derived based on the assumption that crack growth occurs when the
J-Integral attains a critical value.
2.1 The Time Dependent Failure Assessment Diagram (TDFAD)
The R6 Option 2 FAD has been extended to a time dependent failure assessment
diagram (TDFAD) which addresses limited high temperature crack growth 3. This is
done by replacing KIC, in Eqn (1) by a creep toughness corresponding to a given
crack extension at a given time, denoted ,cmatK a t , and σ0.2 in Eqn (2) by the 0.2%
inelastic (creep and plastic) strain from an isochronous stress-strain curve at a
particular time and temperature, c
2.0 , also called the 0.2% creep strength. The value
of c
2.0 will decrease as time increases i.e. creep strain increases. In the TDFAD, for
the case of a single primary load, the parameters Kr and Lr are therefore defined as
r cmat
KK
K (6)
c
ref
rL2.0
(7)
The cut off point maxrL is defined on the TDFAD as
c
rrL
2.0
max
(8)
where r is the stress to cause creep rupture at the same time as c
2.0 is evaluated.
If Lr exceeds maxrL , failure is expected to occur by creep rupture rather than by
fracture. In order to be consistent with the R6 procedure, maxrL in the TDFAD should
not exceed the value of maxrL defined in Eqn (5). The time to rupture in a uniaxial
creep test over a range of stresses can often be approximated by the power-law
relation,
rvr rt B (9)
where Br and vr are the rupture coefficient and exponent, respectively.
The time dependent failure assessment curve is based on the assumption that
crack growth occurs when the dependent time parameter, J(t), attains a critical value.
A failure assessment diagram for a specific time is defined by the equations
21
2.03
2.0 2
ref
cr
cr
ref
rE
L
L
EK
for
maxrr LL (10)
0rK for maxrr LL (11)
In Eqn (10) ref is the total strain at reference stress at a given time, given by the sum
of the elastic and plastic strain and the total creep strain accumulated in that time i.e.
e p c
ref ref ref reft t (12)
Note that ref is the true strain at true stress ref (= Lr0.2) (and not the engineering
strain). Note also that at short times e p
ref ref reft and 0.2 0.2
c , and Eqn (10)
reduces to the R6 Option 2 curve. At long times c
ref reft and Eqn (10) reduces
to
12c
refr
ref
EK
(13)
Equation (13) can be derived for steady state creep conditions, where the creep
strain rate is a constant, based on the assumption that at long times J(t), evaluated,
can be approximated by the product of C* and time (i.e. J(t) ≈ C*t 19) and C* is given
by the reference stress estimate 1. The TDFAD can therefore measure the proximity
to failure by fast fracture, creep crack growth, plastic collapse and creep rupture.
Therefore, in the TDFAD approach, a failure mode does not have to be pre-defined.
2.2 Application of TDFAD to Predict Creep Crack Initiation (CCI)
The TDFAD can be used to predict if a crack will extend a distance a in a given time
or the time required for a specified amount of crack extension. Since CCI can be
defined as the period of time required for a small increment of crack growth, a, the
TDFAD may be used to predict CCI times. For some materials the curves may not
vary greatly with time and curves for longer times can be used to provide a
conservative TDFAD for an assessment at shorter times 8.
To predict CCI an initial time estimate is made and the values of Lr and Kr, and
their associated parameters, are determined for the specified initiation distance, a,
at that time. The point (Lr , Kr) is then plotted on the TDFAD. If the point lies within
the TDFAD then the crack extension is less than a and creep rupture is avoided in
the assessment time. To determine an initiation time, ti, a time locus of points (Lr, Kr)
is constructed at various times. The time for a crack extension a is given by the
intersection of a point on this locus (for a given time) with the failure assessment
curve for the corresponding time. An iterative process is required to match the times
associated with the point of intersection of the locus and the TDFAD constructed.
The procedure is further detailed in 8, 9.
2.3 Isochronous Stress-Strain Data
Isochronous stress-strain curves for the specified temperature are required in order
to determine c
2.0 and the overall TDFAD. Isochronous stress-strain data are
generated here using the elastic-plastic and creep material response. The method
used follows the procedure in the RCC-MR design code 20 for primary-secondary
creep of Type 316 stainless steel material. Thus, the primary and secondary creep
strain increments, cp and
cs , are calculated according to
/1/ (1 1/ )pn pc p pp ppA t (14)
c ns A t (15)
The creep strain increment, c , is equal to the larger of the two increments
calculated from Eqns (14) and (15) i.e.
c
cp for
cp ≥
cs
(16)
cs for
cp <
cs
The primary and secondary creep constants in Eqns (14) and (15) are given in Table
1 for 316H stainless steel at 550° C and P22 steel at 565° C. For a particular time,
the total strain at any stress level is given by the sum of the elastic and plastic strain
and the total creep strain accumulated in that time, i.e.
, ,total e pl c
t
t t (17)
3 Evaluation of the Creep Toughness Parameter, c
matK
The c
matK parameter is evaluated from the load displacement curve generated during
a CCG test using the relation 3, 8.
12
2 ' '
1
cpc
matn n
E U n E PK K
B W a n B W a
(18)
where Up is the area under the load displacement curve associated with plasticity, W
is the specimen width, Bn is the net specimen thickness between any side-grooves, a
is the crack length and n the secondary creep power-law stress exponent (see Eqn
(15)) and η a geometry function (η = 2.2 for C(T) specimens 21). Note that the cmatK
relation has been modified since the work in 9.
In the absence of specimen load-displacement data a method has been proposed
to estimate c
matK from CCI and CCG data. Under steady state conditions the CCG
rate, a , may be described by the expression 2
*a DC (19)
where D and are temperature dependent crack growth constants. The CCI time
may also be described by the C* parameter according to the power-law relationship
* i
i it DC (20)
where Di and i are temperature dependent CCI constants. Assuming widespread
creep conditions, a constant secondary creep strain rate and using the reference
stress estimate of C* 1, it can be shown that c
matK may be estimated from CCI data
according to the relation 22
1211 1
iimat
c iK ED t
(21)
Alternatively, if crack growth is assumed a continuous process commencing at zero
time, then c
matK may be estimated from CCG data 22 using
11 2
11mat
c
aK E t
D
(22)
It can therefore be seen from Eqn (22) that c
matK is expected to decrease with time
according to 1
1 21mat
cK t
(23)
Creep crack initiation and growth models 23-25 predict that 1i n n thus,
substituting for in Eqn (23) it may be written
12mat n
cK t
(24)
It is therefore expected that mat
cK follows the power-law relationship
,mat j
c iK a t Ht (25)
where H is the correlating coefficient and, j is the power-law exponent.
4 Creep Deformation and CCG Behaviour of P22 and 316H Steel
Firstly, the high temperature tensile and creep deformation and rupture behaviour of
the two materials are compared to reveal their differences, which will be reflected in
the form of their TDFADs. The true-stress vs. true-strain curves of both materials are
shown in Figure 1 up to the point in the tests where a failure mechanism intervened.
The tensile properties are given in Table 1. The shape of the tensile behaviour of P22
and 316H are clearly different. The 0.2% proof stress of P22 is almost 70% higher
than that of 316H and exhibits relatively little hardening. On the contrary, 316H has a
high degree of work hardening and has a 10% higher plastic ductility, εf, than P22
steel, based on engineering strain (Eng) values.
The secondary creep strain rate and rupture-time vs. stress relations for the two
steels are compared in Figure 2(a) and (b), respectively. Note that the stress values
for 316H are true-stress values accounting for plastic strain on loading. However, in
the absence of loading data, and since the applied stress are significantly less than
the σ0.2 of the steel (thus little plastic strain is expected on specimen loading), the
engineering stress has been used for the P22 tests. In Figure 2(a) the stress to
cause a given strain rate or rupture time is around a factor of three higher for 316H
than P22. The creep strain rates for a given stress are therefore significantly higher,
and rupture times lower, for P22 steel in comparison to 316H at these temperatures.
The uniaxial creep failure strain (creep ductility), cf , of P22 is over twice that of
316H based on both axial and reduction of area (ROA) measurements (see Table 1).
4.1 Isochronous Stress Strain Curves
The materials tensile data and creep laws have been combined to generate
isochronous stress-strain curves as specified in Section 2.3 using the material
properties given in Table 1. The resultant curves are very different for the 316H and
P22 steel as shown in Figure 3(a) and (b), respectively, for times up to 100,000 hours.
The P22 steel’s curves are strongly time dependent even at short times. In fact the
P22 curve for a time of one hour almost overlays the 316H curve at 100,000 hours.
The corresponding 0.2% inelastic (creep and plastic) strain, c
2.0 , are illustrated and
compared in Figure 4. Little change in c
2.0 for 316H steel is observed for the first
1000 hrs whilst creep strains dominate in the P22 steel. Even at very short times it
can be seen that for P22 c
2.0 reduces by 50% due to creep strain accumulation in
the first hour alone.
5 Creep Fracture Behaviour
5.1 CCG Behaviour
Creep crack growth test data on the compact tension specimen, C(T), from 26 for P22
and 27, 28 for 316H steel have been re-analysed in accord with recent changes in data
analysis procedures 2, 3. A sizable data set is available for 316H with test durations
ranging between 100 and 18,000 hours. The CCG tests on P22 steel were relatively
short ranging between 300 and 4,400 hrs. The significance of plasticity on loading of
the 316H steel specimens and it’s influence on CCG behaviour has been described
in 9, 29, 30. The P22 test load-up data was not available for analysis. However, it is
expected that there is little plasticity on loading of P22 specimens since the ratio σref
/σ0.2, on load up is less than 0.5 for all specimens and is on average 0.31 and 0.45
assuming plane strain and plane stress conditions, respectively. For the 316H
specimens this ratio was close to or exceeded unity assuming plane strain conditions,
except for the long term tests where the ratio was approximately 0.78.
Mean line power-law regression fits have been made to the CCG data as shown in
Figure 5. Upper bound (UB) and lower bound (LB) fits are obtained by offsetting the
mean line by ± 2 standard deviations (s.d.) of the regression fit, assuming a constant
slope. Separate fits have been made to the long and short term tests of 316H in
Figure 5(a) due to the distinct CCG behaviour observed in the long term tests, where
plasticity is limited and thus high specimen constraint effects maintained 30. The CCG
rate constants for these fits (see Eqn (5)) are given in Table 2 Similar CCG behaviour
is exhibited by both steels for C* > 1×10-5 MPamh-1, however significant tails are
observed for P22 though the validity criterion 2 are met.
5.2 CCI Behaviour
The CCI times for 0.2 mm and 0.5 mm of crack extension are plotted against the
experimentally determined C* parameter at the corresponding time in Figure 6 and
Figure 7 for 316H and P22 steel, respectively. Regression fits have been made to the
data and the constants in Eqn (20) determined, accounting for the degree of data
scatter (see Table 3). The CCI time data for 316H (Figure 6) appear to form
reasonable correlations with the C* parameter, though the power-law correlation
exponent, i , is significantly less than 1n n as predicted from CCI models 25, 29.
The value of i obtained from the regression fit for P22 data for Δa = 0.2 mm is
greater than unity indicating that the experimentally determined C* parameter is not
an appropriate correlating parameter in this case since, as indicated by the tails
shown in Figure 5, steady state CCG conditions have not been achieved 2. Also,
since the data set for P22 is relatively small it can be difficult to establish the data
trend. More reasonable correlating parameter are obtained for the P22 data at Δa =
0.5 mm, though again i is significantly less than 1n n . A significant degree of
data scatter is observed for both materials, quantified by the UB/LB values of Di,
which are generally a factor of 5 greater or less than the mean value, respectively.
5.3 Creep Toughness Data, mat
cK
The mat
cK values at Δa = 0.2 and 0.5 mm of crack extension have been calculated
using Eqn (18) for both materials in homogenous parent material (PM) and weldment
(WM) conditions. A regression fit has been made to the data to obtain the values of H
and j in Eqn (25) and again UB/LB fits made by offsetting the mean by ± 2 s.d. of the
data set (see Table 4 and Table 5). In addition, the best line fit has been made to the
data assuming a slope of 1 2n as predicted in Eqn (24). Note that sensible
trendlines have not been obtained using Eqns (21) and (22) in conjunction with the
CCG and CCI regression data detailed in Table 2 and Table 3 , respectively, and
thus are not shown in the following figures.
5.3.1 Homogenous Parent Material (PM) mat
cK Data
The creep toughness data of 316H PM at 565 °C has previously been presented in 9,
31-33. However, this data has been re-analysed here for consistency, and to be in
accord with recent modifications in the mat
cK evaluation procedure. The slope j of the
regression fits to the 316H data in Figure 8, is a factor of 5 steeper than predicted
using Eqn (24). The best fit line to the data using Eqn (24) provides a reasonable fit
to the data for less than 500 hrs and 800 hrs for Δa = 0.2 and 0.5 mm, respectively.
For times greater than these, a change in the data trend can be observed.
The corresponding mat
cK data for PM P22 steel are presented in Figure 9. Creep
toughness data for P22 steel at 550 °C has been presented in 12. mat
cK is expected to
be insensitive to such small variations in temperature 8, thus the data in 12 at 550 °C
has been combined with the data analysed here at 565 °C. The influence of
temperature on mat
cK is further discussed for materials of similar compositions to
those analysed here in 10.
The regression fit values for Δa = 0.2 mm were non-sensible as the negative j
value in Table 4 indicates an increase in mat
cK with time. For Δa = 0.5 mm, however,
j ≈ 1 2n as predicted in Eqn (24). For the P22 data therefore the mean lines shown
in Figure 9 are the best fits of Eqn (24) to the data set, and the UB/LB factors are
assumed to be equal to that obtained from a regression fit to the data.
5.3.2 Comparison of Parent and Weldment Data
The creep toughness data of 316 steel compact tension specimen weldments have
been determined and compared to PM data in 16 where full details of the weldment
geometry can be found. This weldment data is compared to additional and re-
analysed PM data in Figure 10. Due to the limited amount of weldment data available
the slope of the weldment trend line fitted to the data has been assumed to be equal
to that of the regression fit to the PM. A relatively good fit is observed, the coefficients
for which are given in Table 4. For a given time, the mean mat
cK value of the 316
weldment specimens is a factor of approximately 2 less than that for a PM.
Creep toughness data from C(T) weldment specimens of P22 steel are compared
to PM specimens at 565 °C and 550 °C for both Δa = 0.2 and 0.5 mm in Figure 11(a)
and (b), respectively. The PM and weldment data at both temperatures fall within the
same scatter bands. A best fit line assuming a slope j = 1 2n , as in Eqn (24), has
been made to the PM and weldment data sets, where n has been taken to be equal
to the PM value. This assumption is justified by the fact that the value of n
determined from tests performed on cross-weld uniaxial specimens of P22 at 550 °C,
which are considered to most represent the behaviour of C(T) weldments, were
found equal to the PM test values 26. Note that sensible regression fits were not
obtained for this data set. On average there is a 10% difference between the PM and
weldment value of mat
cK for a given time and bound, whereas there is around a 40%
and 80% difference between the UB or LB and mean value of mat
cK for a given time,
for the PM and weldment data, respectively, as can be deduced from Table 5.
Therefore, within the extent of data scatter, little difference in creep toughness
behaviour is observed between the two material conditions, for the P22 steel.
6 TDFAD Formation
The TDFADs for a range of times (t = 0, 1, 10, 100, 1000, 10000 and 100000 hrs)
have been determined from Eqn (10),(11), (14)-(17), using the PM data given in
Table 1, and are shown in Figure 12. Also shown in Figure 12 for comparison
purposes is the R6 Option 1 curve (see Eqn (3)). Note that the R6 cut off point, max
rL
(see Eqn (5)) is the appropriate value to use (see Section 2.1) for times less than
10,000 hrs for the 316H material and for all times in the case of P22.
As can be seen in Figure 12(a) and described in 9 the 316H TDFAD is insensitive
to time and deviates little from the R6 option 1 curve. The P22 TDFAD however, is in
relatively good agreement with the R6 Option 1 curve at time 0 hrs, but almost
instantly deviates significantly from it. These trends are due to the relatively low and
very high creep strain rates experienced in 316H and P22, respectively, (see Figure
2(a) and Figure 3) at these temperatures.
7 CCI Time Predictions
The TDFAD procedure for predicting CCI times is evaluated for both steels. A
program has been developed that determines the intersection of a point (Kr, Lr) for a
given time and crack extension with the TDFAD of corresponding time. Predictions
for both PM and weldment data have been determined, though note the TDFADs
have strictly been derived from PM data. The CCI times have been predicted for the
tests on homogenous PM and weldment C(T) specimens 16, 21, 27. These tests have
been used to derive the relationship of creep toughness on time, thus appropriate
predictions are expected. In addition, CCI data are available for feature tests on P22
PM and weldment pipe components, as detailed in 34. These results are also
predicted here using the TDFAD procedure. Predictions on C(T) specimens have
been based on the plane strain reference stress solution. Details of the stress
intensity factor and reference stress solution for the pipe component are given in 34.
The TDFADs predicted CCI time, tiPredicted
, is compared to the experimentally
determined value, tiExp
, in Figure 13-Figure 15. Included in these figures is the line for
tiPredicted
= tiExp
. Points situated below this line indicate a conservative prediction, and
vice-versa. Predictions have been obtained using the mean and LB values of mat
cK
calculated using Eqn (25) with the regression fit values shown in Table 4 for 316H
and the best fit values with an assumed slope of j = 1 2n (see Eqn (24)) as shown
in Table 5 for the P22 material. The predictions based on mean or LB mat
cK values
are shown as open and grey symbols, respectively.
The weldment and PM specimen predictions are shown together in Figure 13 for
the 316 steel. Similar trends are observed for the two material conditions at both
Δa = 0.2 and 0.5 mm. Predictions based on mean mat
cK values are often, but not
always, conservative whereas the use of LB mat
cK values consistently gives
conservative predictions. The same is true for C(T) specimen PM and weldment data
for P22 material shown in Figure 14 and Figure 15, respectively, except for one point
in Figure 14(b) and Figure 15(a) which is just above the line using a LB mat
cK value.
However, since the data set available for P22 is limited, less confidence can be
assigned to the appropriateness of the TDFAD for predicting CCI for P22, especially
for long term conditions since long term data are unavailable for this material.
An initiation distance Δa = 0.5 mm has been deemed suitable for the feature
components 34, thus pipe data are not included in Figure 14(a) and Figure 15(a).
Predictions for the pipe components are found to be very conservative in all cases
with tiPredicted
predicted being less than 5% of tiExp
. The degree of uncertainty
associated with tiExp
measurements and due to the approximations made in
evaluating the parameters K and σref for these components leads to higher
uncertainties in their CCI time predictions compared to that for laboratory test
specimens. These additional uncertainties may contribute to the excessive
conservatism in the CCI times predicted for these components. This uncertainty is
however not easily quantified. The influence of the reference stress solution on the
CCI predictions has previously been examined and discussed in 9.
8 Discussion
The appropriate isochronous stress-strain response of a location being either within
the parent, weld or HAZ of a weldment will be affected by the isochronous stress-
strain response of the surrounding material region. An equivalent isochronous stress-
strain response may be defined, with intermediate isochronous properties, which will
be a function of weldment geometry, loading, crack geometry, size and location. Note
that for the weldment tests considered in this work the crack was located in the HAZ
adjacent to the HAZ/PM interface. The equivalent isochronous stress-strain curve is
based on the mis-match limit load and equivalent material stress-strain curve
described in R6 17. A conservative assessment is however obtained using the tensile
properties of the weaker material, which would be the 316H parent material in the
case of the 316 specimen weldments which consist of 316H PM and 316L weld
metal 16. The mis-match reference stress for an overmatched weld is expected to be
greater than that for a homogeneous specimen (see e.g. 35). Thus, should a
conservative prediction be obtained for an overmatched weldment using the
materials PM properties and a homogeneous reference stress solution then the use
of the mismatch reference stress would further increase the degree of conservatism.
Tensile test data are not available for the P22 weld material at 565 °C however
results in 36 from a similar weld tested at 550 °C indicates that the welds yield
strength is slightly (7%) less than the PM, however their general stress-strain
behaviour of the weld is very similar to that of the PM. Therefore, it is considered that
mismatch effects may not be significant for the P22 weldments analysis. The
influence of mismatch on the isochronous stress-strain curves of Cr-Mo steel,
following the R6 approach, have been examined in 15 where the influence of
geometry, crack size and time on the TDFAD was found negligible. A simplified
procedure for evaluating isochronous stress-strain curves has been proposed in 13
(neglecting plasticity and assuming the elastic response of the entire weldment is
equal to the PM’s response) and applied to a 1Cr0.5Mo steel weldment. A
dependency of the TDFAD on time was shown in 13, however, the deviation of the
weldments TDFAC from the PM is curve was not demonstrated.
Since the TDFAD is being used to predict CCI it is expected that creep fracture
would be the failure mode predicted. This is true for all cases examined for the 316H
PM and weldments and the majority of cases for the P22 PM and weldment analyses
using the lower bound mat
cK , which leads to higher Kr values. However, for the vast
majority of cases failure by plastic collapse is predicted for the P22 PM and weldment
analyses when the mean mat
cK values are employed, which is considered unrealistic.
This is due to the strong time dependence of c
2.0 causing a rapid increase of Lr to
values greater than max
rL . The time dependency of the rupture stress r is small in
relation to c2.0 , thus max
rL calculated from Eqn (8), indicating creep rupture, does not
fall below that of Eqn (5), indicating plastic collapse.
There are considerable differences between the TDFADs for both steels. It has
been demonstrated here and previously elsewhere (see e.g. 8), that due to the
insensitivity of the 316H steels TDFAC to time a single curve for a given time or even
the R6 Option 1 curve may suffice. However, the significant time dependency of the
P22 steel shown here demonstrates that this is not the case for this ferritic steel. This
was also noted for the similar steel examined in 37. An influence of tensile curve fitting
on the accuracy of the results was noted in 5. The Ramberg-Osgood material model
widely employed to describe a materials tensile response is known to cause
inaccuracies especially for high strain hardening austenitic steels 38. In this work
however such issues are negated by employing the materials experimentally
measured tensile test data.
The mat
cK estimates obtained from using CCI and CCG data (see Eqn (21) and
(22)) have been unsuccessful for the cases examined here, though they have
provided satisfactory results elsewhere 8, 10. The best fit line from Eqn (24) has
provided a reasonable fit to all the P22 mat
cK vs. time data and to the short term 316H
data, but can not describe the longer term 316H steel data. The apparent change in
slope between the long term and short term mat
cK vs. time data may indicate a
change in material fracture behaviour, as suggested in 31. However, within the extent
of data scatter no firm conclusions can be made.
The influence of using the LB bound or mean mat
cK value has been examined here,
and significant differences are obtained in both cases, including a change of
predicted failure mode for the P22 steel. The influence of the reference stress
solution on the CCI predictions has previously been examined in 9. The plane stress
reference stress is greater than the plane strain reference stress and therefore leads
to higher degrees of conservatism. Using the plane stress reference stress solution
with a LB mat
cK value will therefore lead to conservative predictions for all cases
considered here.
Long term CCI and CCG tests are more representative of component operating
conditions. The difference between the CCG rate and mat
cK trends for long and short
term data signify that more long term tests are required to verify the TDFAD
prediction method for use in high temperature components.
9 Conclusions
The creep toughness parameter, mat
cK , for a crack extension of 0.2 mm and 0.5 mm
has been determined for an austenitic 316H steel at 550 °C and ferritic P22 steel at
565 °C from creep crack growth (CCG) tests on the compact tension, C(T),
specimen geometry. Both homogenous parent material (PM) and weldment
specimen tests have been considered. mat
cK shows a relatively weak dependency on
time for the P22 steel, however a clear decrease in mat
cK with time is observed for
the 316H material, especially at long times. Significant data scatter has been
observed in the mat
cK data for both materials, which has been quantified. For the P22
steel the influence of mat
cK on time had to be predicted using models since, due to
the extent of data scatter within the relatively small data set, a sensible regression
line fit could not be achieved. For a given time, the mean mat
cK values of the 316
weldment specimens are found to be a factor of 2 less than that of the PM specimens.
Within the extent of data scatter, little difference in creep toughness behaviour is
observed between the two material conditions for the P22 steel. Isochronous stress-
strain curves and time dependent failure assessment diagrams (TDFAD) have been
shown for a range of times for both the 316H and P22 PM steels. Due to the
relatively low creep strain rates in the 316H steel at 550 °C, these curves are
relatively insensitive to time and little change is observed in the 316H materials 0.2%
creep strength 0.2
c for times less than 10,000 hrs. On the contrary the P22 curves
rapidly deviate from their tensile curves (at t = 0 hrs) and 0.2
c halves within the first
hour of creep. A program has been developed to obtain explicit creep crack Initiation
(CCI) time predictions using the TDFAD method. CCI time predictions have been
obtained for the CGG tests on the PM and weldment C(T) specimens and in addition
for CCG data on PM and welded P22 pipe feature tests using the TDFAD derived
from PM data. Reasonable predictions are generally obtained using the mean bound
value of mat
cK , though not always conservative assuming plane strain conditions.
Conservative predictions are almost always obtained when LB mat
cK values are
employed and may be ascertained by assuming plane stress conditions. Although
considerable differences are observed in the form of the mat
cK data and TDFADs of
both austenitic 316H steel at 550 °C and ferritic P22 steel at 565 °C reasonable and
conservative CCI time predictions can be achieved for both materials following the
TDFAD approach. It is however essential that the influence of time on the TDFAD is
considered for the P22 steel. Further long term tests are recommended for the
validation of the TDFAD method to predict the CCI times of in-service components.
10 References
1. Webster GA, Ainsworth RA (1994) High Temperature Component Life Assessment. 1st edn. Chapman and Hall, London.
2. ASTM (2007) E1457-07: Measurement of Creep Crack Growth Times in
Metals. Annual Book of ASTM Standards. ASTM International, 10121035. 3. BEGL (2003) An Assessment Procedure for the High Temperature Response
of Structures. British Energy Generation Ltd. 4. Lamb M (2001) A Review of Creep Toughness of Ferritic Steels. BNFL. 5. Dogan B, Petrovski B, Ceyhan U (2005) High Temperature Crack Initiation
and Defect Assessment of Power Plant Steel Weldments. In: Shibli IA, Holdsworth SR, Merckling G, eds. Creep & Fracture in High Temperature
Components Design and Life Assessment Issues, ECCC Creep Conference. PA: DEStech Publications, IMechE, London.
6. Fedeli G, Gampe, U., Prunier, V., Nikbin, K. M., Andersson, H., Patiraj, B. and Shibli, I. A. (1998) HIDA Activity on 2¼Cr1Mo Steel. Materials at High Temperature. 15: 27-35.
7. Kutz M (2002) Handbook of materials selection John Wiley and Sons, New York ; Chichester
8. Ainsworth RA, Hooton, D. G. and Green, D. (1999) Failure Assessment Diagrams for High Temperature Defect Assessment. Engineering Fracture
Mechanics. 62: 95109. 9. Davies CM, O'Dowd NP, Dean DW, Nikbin KM, Ainsworth RA (2003) Failure
Assessment Diagram Analysis of Creep Crack Initiation in 316H Stainless
Steel. International Journal of Pressure Vessels and Piping. 80: 541551. 10. Xuan FZ, Tu ST, Wang ZD, Gong JM (2005) On the Creep Fracture
Toughness of 2¼Cr1Mo Steel. Key Engineering Materials. 297-300: 14641469.
11. Mueller F, Scholz A, Berger C (2007) Comparison of Different Approaches for the Estimation of Creep Crack Initiation. Engineering Failure Analaysis. 14:
15741585. 12. Dogan B, Ceyhan U, Petrovski B (2007) High Temperature Crack Initiation
and Defect Assessment of P22 Steel Weldments using Time Dependent Failure Assessment Method. Engineering Fracture Mechanics. 74: 839–852.
13. Ma CW, Xuan F, Wang ZD, Tu ST (2004) Isochronous Stress Strain Curves of Low Alloy Steel Cross Weld Specimen In High Temperature. Acta
Metallurgica Sinica (English Letters). 17: 612617. 14. Dogan B, Ceyhan U, Nikbin KM, Petrovski B, Dean DW (2005) European
Code of Practice for Creep Crack Initiation and Growth Testing of Industrial Specimens. Submitted for Publication.
15. Xuan F-Z, Tu S-T, Wang Z (2006) A Modified Time-Dependent Failure Assessment Diagram for Cracks in Mismatched Welds at High Temperatures.
29: 157166. 16. Davies CM, Dean DW, Nikbin KM, O'Dowd NP (2007) Interpretation of Creep
Crack Initiation and Growth Data for Weldments. Engineering Fracture Mechanics, 882–897.
17. BEGL (2001) Assessment of the Integrity of Structures Containing Defects. British Energy Generation Ltd.
18. British Standard (1999) BS 7910: Guide on Methods for Assessing the Acceptability of Flaws in Metallic Structures. BSI, London.
19. Ainsworth RA, Budden PJ (1990) Crack Tip Fields under Non-Steady Creep
Conditions. Estimates of the Amplitude of the Fields. Fatigue & Fracture of
Engineering Materials & Structures. 13: 263276. 20. RCC-MR (1985) Design and Construction Rules for Mechanical Components
of FBR Nuclear Island. AFCEN, Paris. 21. Davies CM, Kourmpetis M, O'Dowd NP, Nikbin KM (2006) Experimental
Evaluation of the J or C* Parameter for a Range of Cracked Geometries. Journal of ASTM International.
22. Ainsworth RA (1993) The Use of a Failure Assessment Diagram for Initiation and Propagation of Defects at High Temperature. Fatigue Fracture of
Engineering Materials and Structures. 16: 10911108. 23. Nikbin KM, Smith, D. J. and Webster, G. A. (1983) Influence of Creep Ductility
and State of Stress on Creep Crack Growth. Advances in Life Prediction
Methods at Elevated Temperatures. 249258. 24. Nikbin KM, Smith, D.J., Webster, G.A. (1984) Prediction of Creep Crack
Growth from Uniaxial Creep Data. Proceedings of the Royal Society. A 396:
183197. 25. Austin TSP, Webster GA (1992) Prediction of Creep Crack Growth Incubation
Periods. Fatigue and Fracture of Engineering Materials and Structures. 15:
10811090. 26. Célard N (2000) Determination of a Unified Defect Assessment Procedure for
High Temperature Applications. Department of Mechanical Engineering. Imperial College London, London.
27. Dean DW, Gladwin DN (2007) Creep Crack Growth Behaviour of Type 316H Steels and Proposed Modifications to Standard Testing and Analysis Methods.
The International Journal of Pressure Vessels and Piping. 84: 378395. 28. Bettinson AD (2002) The Influence of Constraint on the Creep Crack Growth
of 316H Stainless Steel. Department of Mechanical Engineering. Imperial College London, London.
29. Davies CM, Mueller F, Nikbin KM, O'Dowd NP, Webster GA (2006) Analysis of Creep Crack Initiation and Growth in Different Geometries for 316H and Carbon Manganese Steels. Journal of ASTM International.
30. Davies CM, Dean DW, Yatomi M, Nikbin KM (2008) The Influence of Test Duration and Geometry on the Creep Crack Initiation and Growth Behaviour of 316H Steel. to appear in Materials Science and Engineering A, Creep 2008 Special Issue.
31. Dean DW, Gladwin DN (2001) Characterisation of Creep Crack Growth Behaviour in Type 316H Steel using both C* and Creep Toughness Parameters. In: Parker DJ, ed. Proceedings of the 9th International Conference on Creep and Fracture of Engineering Materials and Structures, Swansea, 751–761.
32. Dean DW, O'Donnell M.P. (2001) Alternative Approaches in the R5 Procedures for Predicting Initiation and the Early Stages of Creep Crack
Growth. Creep and Fatigue at Elevated Temperatures, Tsukuba, Japan, 315319.
33. Dean DW, Hooton DG (2003) A Review of Creep Toughness Data for Austenitic Type 316 Steels. British Energy Generation Ltd.
34. Wasmer K, Davies, C.M., Nikbin K.M., O'Dowd, N.P., Webster, G.A. (2003) A Study of Creep Crack Initiation and Growth in Welded P22 Steel Pipes. 2nd International Conference Integrity of High Temperature Welds. IOM Communications Ltd, London, 413-423.
35. Song T-K, Kim Y-J, Kim J-S, Jin T-E (2007) Mismatch limit loads and approximate J estimates for tensile plates with constant-depth surface cracks in the center of welds. International Journal of Fracture. 148: 343-360.
36. Dogan B, Petrovski B (2001) Creep crack growth of high temperature weldments. International Journal of Pressure Vessels and Piping. 78: 795-805.
37. Xuan F, Shandong T, Zhengsong W (2004) TDFAD Approach to High Temperature Defect Assessment and its Engineering Application. Chinease
Journal of Mechanical Engineering. 17: 537542. 38. Gardner L, Ashraf M (2006) Structural Design for Non-linear Metallic
Materials. Engineering Structures. 28: 926934.
11 Tables
Table 1: Material properties for homogeneous parent material 316H stainless steel at 550 °C and P22 steel at 565 °C
316H P22 (PM)
A (MPa1/n
h-1) 1.47×10-34 3.21×10-27
n 11.58 10.68
np 7.45 2.47
Ap MPa pn pt 2.60×10-23 1.0×10-8
p 0.746 0.3
E (MPa) 140,000 140,135
σ0.2 (MPa) 170 284
σUTS (MPa) 442 365
Br (MPavr h) 5.27×1031 1.43×1022
vr 11.3 9.11
σflow (MPa) 306 327
εf (%) (Eng) 37 27 cf (%) (Axial) 8 31
cf (%) (ROA) 21 65
Table 2: Regression fit constants to CCG rate vs. C* data (Eqn (19)) from long term (LT) and short term (ST) tests on 316H and tests on P22 steel.
316H (LT) 316H (ST) P22
D Mean 9.25 3.45 4.52
D UB 16.91 8.26 16.87
D LB 5.06 1.44 1.21
0.73 0.75 0.75
Table 3: Regression fit constants to CCI time vs. C* data (Eqn (20)) from tests on
homogenous parent material 316H and P22 steel for crack extensions, Δa, of 0.2 and
0.5 mm.
316H P22
Δa (mm) 0.2 0.5 0.2 0.5
Di Mean 0.7 3.9 9.3 ×10-4 22.1
Di UB 5.0 17.9 4.0 ×10-3 4.5
Di LB 0.1 0.8 2.2 ×10-4 0.93
i 0.55 0.47 1.1 0.44
Table 4: Mean, upper bound (UB) and lower bound (LB) regression fit constants to mat
cK vs. time data (Eqn (25))of homogeneous parent material (PM) and weldment
316H and P22 PM specimens.
316H 316H P22
PM Weldment PM
Δa (mm) 0.2 0.5 0.2 0.5 0.2 0.5
H Mean 242.4 224.5 117.8 173.0 29.8 73.3
H UB 449.7 611.5 211.8 289.0 51.5 136.8
H LB 130.6 224.5 65.5 103.5 17.3 39.3
j 0.20 0.23 0.20 0.23 -0.06 0.04
Table 5: Mean, upper bound (UB) and lower bound (LB) constants for the mat
cK v.s.
time relationship of Eqn (25) for homogenous parent material (PM) specimens of
316H and of P22 steel, and weldment specimens of P22 steel assuming j = 1 2n
316H P22
PM PM Weldment
Δa (mm) 0.2 0.5 0.2 0.5 0.2 0.5
H Mean 119.8 135.1 51.35 71.96 47.2 62.1
H UB 222.2 223.0 88.68 134.3 69.5 88.3
H LB 64.5 81.9 29.73 38.56 32.0 43.7
j = 1 2n 0.043 0.047 0.047
12 Figures
0.0
100.0
200.0
300.0
400.0
500.0
600.0
0.00 0.05 0.10 0.15 0.20 0.25 0.30
True Strain
Tru
e S
tress (
MP
a)
P22 565 °C
316H 550 °C
Figure 1: Comparison of the high temperature tensile behaviour of 316H stainless steel at 550 °C and ferritic P22 steel at 565 °C.
1.E-06
1.E-05
1.E-04
1.E-03
1.E-02
10 100 1000
σ (MPa)
(h
-1)
P22 Data
316H Data
316H Trendline
P22 Trendline
s
(a)
10
100
1000
10000
100000
10 100 1000σ (MPa)
(
h)
P22 Data
316H Data
316H Trendline
P22 Trendline
(b)
rt
Figure 2: Comparison of (a) secondary creep strain rates and (b) creep rupture time with stress for 316H at 550 °C and P22 at 565 °C.
0.0
100.0
200.0
300.0
400.0
500.0
600.0
0.00 0.05 0.10 0.15 0.20 0.25 0.30Total Strain
Str
ess (
MP
a)
t = 0 ht = 1 h
t = 1000 h
t = 100 h
t = 10 h
t = 10,000 h
t = 100,000 h
(a)
316H 550 °C
0.0
100.0
200.0
300.0
400.0
500.0
600.0
0.00 0.05 0.10 0.15 0.20 0.25 0.30
Total Strain
Str
ess (
MP
a)
t = 0 h
t = 1 h
t = 1000 h
t = 100 h
t = 10 h
t = 10,000 h
t = 100,000 h
(b)
P22 565 °C
Figure 3: The isochronous stress strain curves at a range of times for (a) 316H stainless steel at 550 °C and (b) ferritic P22 steel at 565 °C.
0.0
50.0
100.0
150.0
200.0
250.0
300.0
1.E+00 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05
Time (h)
σc0
.2 (
MP
a)
P22
316H
316H
P22
σ 0.2
Figure 4: Evolution of the 0.2% creep strength, 0.2
c , with time of the 316H stainless
steel at 550 °C and P22 steel at 565 °C.
1.0E-05
1.0E-04
1.0E-03
1.0E-02
1.0E-01
1.0E+00
1.0E+01
1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02 1.0E-01
C* (MPam/h)
da
/dt
(mm
/h)
Long Term Test Data
Short Term Test Data
UB
Mean
LB
316H 550 °C
(a)
1.0E-05
1.0E-04
1.0E-03
1.0E-02
1.0E-01
1.0E+00
1.0E+01
1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02 1.0E-01
C* (MPam/h)
da
/dt
(mm
/h)
Test Data
UB
Mean
LB
(b)
P22 565 °C
Figure 5: CCG rate correlations with the C* parameter for (a) 316H stainless steel at
550 °C and (b) P22 steel at 565 °C including data bounds.
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E+05
1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02
C* (MPam/h)
ti (
h)
Test DataUBMeanLB
(a)
Δa = 0.2 mm
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E+05
1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02
C* (MPam/h)
ti (
h)
Test Data
UBMean
LB
Δa = 0.5 mm
(b)
Figure 6: CCI time correlations with the C* parameter at (a) Δa = 0.2 mm and (b)
Δa = 0.5 mm for 316H stainless steel at 550 °C, including data bounds.
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E+05
1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02
C* (MPam/h)
ti (
h)
Test Data
UB
Mean
LB
(a)
Δa = 0.2 mm
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E+05
1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02
C* (MPam/h)
ti (
h)
Test Data
UB
Mean
LB
Δa = 0.5 mm
(b)
Figure 7: CCI time correlation with the C* parameter at (a) Δa = 0.2 mm and (b)
Δa = 0.5 mm for P22 steel at 565 °C, including data bounds.
.
10
100
1000
1 10 100 1000 10000
t (h)
Kcm
at
(MP
a√
m)
Test Data
UB
Mean
LB
Regression Fit
(a)
Δa = 0.2 mm
Best Fit using Eqn (24)
10
100
1000
1 10 100 1000 10000
t (h)
Kcm
at
(MP
a√
m)
Data
UB
Mean
LB
Regression Fit
(b)
Δa = 0.5 mm316H 550 °C
Best Fit using Eqn (24)
Figure 8: Creep toughness vs. time data for 316H stainless steel at 550 °C at (a)
Δa = 0.2 mm and (b) Δa = 0.5 mm, including mean and upper/lower bound
regression fits and the best fit using Eqn (24).
10
100
1000
1 10 100 1000 10000
t i (h)
Kcm
at
(MP
a√
m)
565 °C
550 °C
UB
Mean
LB
Δa = 0.2 mm
(a)P22
10
100
1000
1 10 100 1000 10000
t i (h)
Kcm
at
(MP
a√
m)
565 °C
550 °C
UB
Mean
LB
Δa = 0.5 mm
(b)
P22
Figure 9: Creep toughness vs. time data for ferritic P22 steel PM at (a) 0.2 mm
(b) 0.5 mm, including mean, upper/lower bound fitted lines.
10
100
1000
1 10 100 1000 10000
t (h)
Kcm
at
(MP
a√
m)
PM Data
WM Data
Mean PM
Mean WM
(a)
Δa = 0.2 mm
316 550 °C
10
100
1000
1 10 100 1000 10000
t (h)
Kcm
at
(MP
a√
m)
PM Data
WM Data
Mean PM
Mean WM
(b)
Δa = 0.5 mm
316 550 °C
Figure 10: Comparison of the creep toughness vs. time data for 316H stainless steel
at (a) 0.2 mm (b) 0.5 mm, for homogenous PM and weldment C(T) specimens.
10
100
1000
1 10 100 1000 10000
t i (h)
Kcm
at
(MP
a√
m)
PM 565 °C
PM 550 °C
WM 565 °C
WM 550 °C
Mean PM
Mean WM
(a)
Δa = 0.2 mm
P22
10
100
1000
1 10 100 1000 10000t i (h)
Kcm
at
(MP
a√
m)
PM 550 °C
PM 550 °C
WM 565 °C
WM 550 °C
Mean PM
Mean WM
(b)
Δa = 0.5 mm
P22
Figure 11: Comparison of the creep toughness vs. time data for P22 steel at 565 °C
at (a) 0.2 mm (b) 0.5 mm, for homogenous PM and weldment C(T) specimens.
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
1.00
0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.60 1.80 2.00
L r
Kr
R6 Option 1
TDFAD t = 0 hrs
Cutoff R6
Cutoff t = 10000 hrs
Cutoff t = 100000 hrs
316H 550 °C
(a)
TDFAD t = 1 → 100,000 h
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
1.00
0.00 0.20 0.40 0.60 0.80 1.00 1.20
L r
Kr
R6 Option 1
TDFAD t = 0 hrs
Cutoff R6
TDFAD t = 1 → 100,000 h
P22 565 °C
(b)
Figure 12: Comparison of the TDFADs at various times with the R6 Option1 curve for homogenous PM (a) 316H stainless steel at 550 °C and (b) P22 steel at 565 °C.
1.E-02
1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 1.E+04
t iExp
(h)
ti P
red
icte
d (
h)
C(T) Data PM Mean
C(T) Data PM LB
C(T) Data WM Mean
C(T) Data WM LB
(a)
Δa = 0.2 mm
316 550 °C
1.E-02
1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 1.E+04
t iExp
(h)
ti P
red
icte
d (
h)
C(T) Data PM Mean
C(T) Data PM LB
C(T) Data WM Mean
C(T) Data WM LB
(b)
Δa = 0.5 mm
316 550 °C
Figure 13: Comparison of the predicted and experimentally determined CCI times from tests on homogenous PM and weldment C(T) specimens of 316 steel at 550 °C
for (a) 0.2 mm and (b) 0.5 mm, using mean and lower bound mat
cK values.
1.E-02
1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 1.E+04
t iExp
(h)
ti P
redic
ted
(h)
C(T) Data Mean
C(T) Data LB
(a)
P22 PM 565 °C
Δa = 0.2 mm
1.E-02
1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 1.E+04
t iExp
(h)
ti Pre
dic
ted
(h)
C(T) Data Mean
C(T) Data LB
Pipe Data Mean
Pipe Data LB
(b)
Δa = 0.5 mm
P22 PM 565 °C
Figure 14: Comparison of the predicted and experimentally determined CCI times from tests on homogenous PM C(T) specimens and pipe components of P22 steel at
565 °C for (a) 0.2 mm and (b) 0.5 mm, using mean and lower bound mat
cK values.
1.E-02
1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 1.E+04
t iExp
(h)
ti P
red
icte
d (
h)
C(T) Data Mean
C(T) Data LB
(a)
Δa = 0.2 mm
P22 WM 565 °C
1.E-02
1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
1.E+04
1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 1.E+04
t iExp
(h)
ti P
red
icte
d (
h)
C(T) Data Mean
C(T) Data LB
Pipe Data Mean
Pipe Data LB
(b)
Δa = 0.5 mm
P22 WM 565 °C
Figure 15: Comparison of the predicted and experimentally determined CCI times from tests on C(T) weldment specimens and welded pipe components of P22 steel at
565 °C for (a) 0.2 mm and (b) 0.5 mm, using mean and lower bound mat
cK values.