In terms of section 22(2)(b) of the Accreditation for Conformity Assessment, Calibration and Good Laboratory
Practice Act, 2006 (Act 19 of 2006), read with sections 23(1), (2) and (3) of the said Act, I hereby certify that:-
SABS COMMERCIAL SOC LTD Co. Reg. No.: 2000/013581/07
Facility Accreditation Number: C07a
is a South African National Accreditation System accredited Certification Body
provided that all SANAS conditions and requirements are complied with
This certificate is valid as per the scope on the accompanying schedule of accreditation,
Annexure “A”, bearing the above accreditation number for
PRODUCT CERTIFICATION
The facility is accredited in accordance with the recognised International Standard
ISO GUIDE 65:1996
While this certificate remains valid, the Accredited Facility named above is authorised to use the
relevant SANAS accreditation symbol to issue facility reports and/or certificates
CERTIFICATE OF ACCREDITATION
________________________________________________________________________
Mr R Josias Chief Executive Officer
Effective Date: 14 February 2012
Certificate Expires: 30 December 2015
ANNEXURE A
SCHEDULE OF ACCREDITATION
Facility Number: C07a
Physical Address: Management Signatory: Mr B Gray
SABS Commercial SOC Ltd
1 Dr Lategan Road
Groenkloof
Cape Town
SABS Commercial SOC Ltd
20 Liesbeeck Parkway Nominated Representative: Mr B Gray
Rosebank
Port Elizabeth
SABS Commercial SOC Ltd
The Acres Office Park
20 Nile Road
Perridgevale
Durban
SABS Commercial SOC Ltd
15 Garth Road
Mayville
Postal Address:
Private Bag X191
Pretoria
0001
Tel: (012) 428 6736
Fax: (012) 428 6703 Issue No.: 07
Cell: 072 865 9858 Date of Issue: 15 October 2013
E-mail: [email protected] Expiry Date: 30 December 2015
DURBAN SCOPE
SABS Commercial SOC Ltd, complies with the accreditation criteria for certification bodies as laid down in ISO/IEC Guide 65 and is authorised to provide Product Certification for the following:
STANDARD PRODUCT
EAC – 3 NACE - DA FOOD PRODUCTS, BEVERAGES AND TOBACCOS
SANS 1675 The manufacture, production, processing and treatment of canned meat products
SANS 449 The manufacture of soft drinks and soft drinks concentrates
Original Date of Accreditation: 01 May 2002 Page 1 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
DURBAN SCOPE
STANDARD PRODUCT
EAC-4 NACE-DB TEXTILE AND TEXTILE PRODUCTS
SANS 1228 Abrasion resistant polymeric gloves: Lined type
SANS 1362 Sewing threads
SANS 1387-4 Woven cotton and similar apparel fabrics Part 4: Cotton jean and drill fabrics
SANS 1394-2 Duvets and pillows Part 2: Synthetic-fibre filled
SANS 1401-5 Woven cotton and similar households fabric Part 5: Terry towelling, towels and
other terry weaves articles
SANS 1613 Warp –knitted terry towelling fabrics and articles
SANS 434 General protective clothing
EAC – 5 NACE - DB TEXTILE AND TEXTILES PRODUCT
SANS 1068 Coats and jackets (protective, unlined)
EAC 12 NACE DG minus 24.4 CHEMICAL PRODUCTS AND FIBRES
SANS 1042 Polymer floor dressing
SANS 1218 Hydraulic oil (anti-wear type)
SANS 1221 Detergent skin cleansers
SANS 1224 Polish stripper
SANS 1225 Ammoniated liquid detergent cleaner
SANS 1251 Engine cooling system protectors
SANS 1330 Waterless hand cleaners
SANS 1344 Medium duty solvent detergent
SANS 1381-4 Materials for thermal insulation of buildings Part 4: Reflective foil laminates (rolls, sheets
and sections)
SANS 1522 Fire extinguishing powders
SANS 1598 Unleaded petrol
SANS 1755 Petroleum jelly (petrolatum)
SANS 1796 Application of durable organic powder coatings for architectural aluminium
SANS 1827 The safety of water treatment chemicals for use in the food industry
SANS 1828 Cleaning chemicals for use in the food industry
SANS 1842 High performance engine lubricating oil for petrol engines (for API Service Category SL)
SANS 1843 High performance engine lubricating oil for diesel engines (for API Service Category CI-4)
SANS 1853 Disinfectants and detergent-disinfectants for use in the food industry
SANS 235 General purpose pure soap
SANS 237 Toilet soap
SANS 307 Penetration grade bitumens
SANS 308 Cutback bitumen (Metric units)
SANS 309 Anionic bitumen road emulsions
SANS 317 Industrial bitumens
SANS 342 Automotive diesel fuel
SANS 548 Cationic bitumen road emulsions
SANS 555 Unused and reclaimed mineral insulating oils for transformers and switchgear
SANS 731-1 Road markings Part 1: Single-pack solvent-borne paints
SANS 825 Hand dishwashing and light duty detergent (liquid)
Original Date of Accreditation: 01 May 2002 Page 2 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
DURBAN SCOPE
STANDARD PRODUCT
EAC – 13 NACE DG 24.4 PHARMACEUTICALS
SANS 1196 Detergent-disinfectants based on organic halogen compounds (other than iodine
compounds), such as fluorine bromine or chlorine
SANS 47 Coal-tar type disinfectant liquids (black and white)
SANS 639 Detergent-disinfectants based on quaternary ammonium compounds
SANS 643 Disinfectants based on stabilized inorganic chlorine compounds
EAC.14 NACE - DH RUBBER AND PLASTIC PRODUCTS
SANS 11 Unplasticized poly (vinyl chloride) (PVC-U) components for external rainwater systems
Single-use medical examination gloves Part 1: Specification for gloves made from
SANS 11193-1 rubber latex or rubber solution
SANS 1173 General purpose textile-reinforced conveyor belting
SANS 1315 Polypropylene pressure pipes
SANS 1366 Steel cord reinforced conveyor belting
SANS 1437 Footwear soiling material and footwear sole and heel components of rubber and plastics
SANS 1601 Structured wall pipes and fittings of unplasticized poly (vinyl chloride) (PVU-U) for buried
drainage and sewerage systems
SANS 20109 Uniform provisions concerning the approval for the production of retreaded pneumatic
tyres for commercial vehicles and their trailers
SANS 4074 Natural latex rubber condoms – Requirements and test methods
SANS 416 Chemical resistant gloves
SANS 4427 Polyethylene (PE) pipes for water supply - Specifications
SANS 68 Single-use sterile rubber surgical gloves - Specifications
SANS 713 Unsaturated polyester (UP) resin system
SANS 791 Unplasticized poly (vinyl chloride) (PVC-U) sewer and drain pipes and pipe fittings
SANS 8773 Plastic piping system for non-pressure underground drainage and sewerage-
polypropylene (PP)
SANS 952 Polyolefin film for damp- and waterproofing in buildings
SANS 952-1 Polymer film for damp-proofing and waterproofing in buildings Part 1: Monofilament and
co-extruded products
SANS 966-1 Components of pressure pipe system Part 1: Unplasticized poly (vinyl chloride) (PVC-U)
pressure pipe systems
SANS 966-2 Components of pressure pipe systems Part 2: Modified poly (vinyl chloride) (PVC-M)
pressure pipe systems
SANS 967 Unplasticized poly (vinyl chloride) (PVC-U) soil, waste and vent pipes and pipe fitting
SANS 971 Conveyor belting – Fire-retardant properties for all construction types
SANS 974-1 Rubber joint rings (non-cellular) Part 1: Joint rings for use in water, sewer and drainage
system
EAC 15 NACE DI minus 26.5.6 NON METALLIC MINERAL PRODUCTS
SANS 141 Glass-reinforced polyester (GPR) laminates
Original Date of Accreditation: 01 May 2002 Page 3 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
DURBAN SCOPE
STANDARD PRODUCT
EAC 16 NACE Di 26.5,6 CONCRETE, CEMENT, LIME PLASTER ect.
SANS 1215 Concrete masonry units
SANS 1263-1 Safety and security glazing materials for buildings Part 1: Safety performance of glazing
Material under human impact
SANS 1294 Precast concrete manhole sections and components
SANS 1381-6 Materials for thermal insulation of buildings Part 6: Cellulose loose fill thermal insulation
material
SANS 1491-1 Portland cement extenders Part 1: Ground granulated blast-furnace slag
SANS 227 Burnt clay masonry units
SANS 50197-1 Cement Part 1: Composition specifications and conformity criteria for common cements
SANS 542 Concrete roofing tiles
SANS 677 Concrete non-pressure pipes
SANS 824 Lime for soil stabilization
SANS 986 Precast reinforced concrete culverts
EAC 17 NACE – DJ 28 FABRICATED METAL PRODUCTS
SANS 1005 Innerspring mattresses
SANS 1143 Mushroom-and countersunk-head bolts and nuts
SANS 121 Hot dip galvanized coatings on fabricate iron and steel articles – Specification and test
method
SANS 1219 Hand hacksaw blades
SANS 1253 Fire-doors and fire-shutters
SANS 1284 Bow-saw frames and blades
SANS 1397 Industrial safety helmets
SANS 1475-1 The production of reconditioned fire-fighting equipment Part 1: Portable and wheeled
(mobile) rechargeable fire extinguishers
SANS 1475-2 The production of reconditioned fire-fighting equipment Part 2: Fire hose reels and above-
ground hydrants
SANS 1567 Portable rechargeable fire extinguishers – C02 type extinguishers
SANS 1700-7-1 Fasteners Part 7: External drive hexagon bolts and screws Section 1: Hexagon head
bolts-product grades A and B
SANS 1700-7-3 Fasteners Part 7: External drive hexagon bolts and screws Section 3: Hexagon head
bolt-products grade C
SANS 1910 Portable refillable fire extinguishers
SANS 193 Fire-dampers
SANS 29 Articles made of precious metals
SANS 4 Locks, latches, and associated furniture for doors (Domestic Type)
SANS 407 Austenitic manganese steel casting
SANS 455 Covered electrodes for the manual arc welding of carbon and carbon manganese steels
SANS 50354 Personal protective equipment against falls from a height- Lanyards
SANS 50355 Personal protective equipment against falls from a height- Energy absorbers
SANS 50358 Personal protective equipment for work positioning and prevention of falls from a height -
belts for work positioning and restraints and work positioning lanyards
Original Date of Accreditation: 01 May 2002 Page 4 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
DURBAN SCOPE
STANDARD PRODUCT
EAC – 17 NACE- DJ 28 FABRICATED METAL PRODUCTS
SANS 50361 Personal protective equipment against falls from a height – Full body harness
SANS 50795 Protection against falls from a height – Anchor devices – Requirements and testing
SANS 543 Fire hose reels
SANS 675 Zinc-coated fencing wire
SANS 727 Windows and doors made from rolled mild steel sections
SANS 809 Industrial body belts
SANS 916 Fishbolts and nuts for light rails
SANS 920 Steel bars for concrete reinforcement
SANS 935 Hot-dip (galvanized) zinc coatings on steel wire
SANS 999 Anodized coatings on aluminium (for architectural applications)
EAC 19 NACE – DL minus 32.1 & DK 29.7
ELECTRICAL AND OPTICAL EQUIPMENT & DOMESTIC APPLIANCES
SANS 1339 Electric cables- Cross-linked polyethylene (XLPE) insulated cables for rated voltages
3,8/6,6 kV to 19/33 kV
SANS 1376-3 Lights for motor vehicles Part 3: Secondary lights
SANS 1464-22 Safety of luminaires Part 22: Luminaires for emergency lighting
SANS 1507-2 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V
to 1 900/3 300 V) Part 2: Wiring cables
SANS 1507-3 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V
to 1 900/3 300 V)
SANS 151 Fixed electric storage water heaters
SANS 1524-1 Electricity payment systems Part 1: Prepayment meters
SANS 1561-1 Rewound and refurbished rotating electrical machine Part 1: Low-voltage three-phase
induction motors
SANS 1973-1 Low-voltage switchgear and controlgear Assemblies Part 1: Type tested Assemblies
SANS 1973-3 Low-voltage switchgear and controlgear Assemblies Part 1: Safety of Assemblies
SANS 60065 Audio, video and similar electronic apparatus – Safety requirements
SANS 60079-0 Electrical apparatus for explosive gas atmospheres Part 0: General requirements
SANS 60079-1 Electrical apparatus for explosive gas atmospheres Part 1: Flameproof enclosures “d”
SANS 60079-11 Explosive atmospheres Part 11: Equipment protection by intrinsic safety “I”
SANS 60079-15 Electrical apparatus for explosive gas atmospheres Part 15: Construction, test and
marking of type of protection “n” electrical apparatus
SANS 60335-1 Household and similar electrical appliances – Safety Part 1: General requirements
SANS 60335-2-24 Household and similar electrical appliances – Safety Part 2-24: Particular requirements
for refrigerating appliances, ice-cream appliances and ice-makers
SANS 60335-2-84 Household and similar electrical appliances-Safety Part 2-84: Particular requirements
for commercial refrigerating appliances with an incorporated or remote refrigerant unit
or compressor
SANS 60598-1 Luminaires Part 1: General requirements and test
SANS 60598-2-1 Luminaires Part 2: Particular requirements Section 1: Fixed purpose luminaires
Original Date of Accreditation: 01 May 2002 Page 5 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
DURBAN SCOPE
STANDARD PRODUCT
EAC 19 NACE – DL minus 32.1 & DK 29.7
ELECTRICAL AND OPTICAL EQUIPMENT & DOMESTIC APPLIANCES
SANS 60598-2-5 Luminaire Part 2-5: Particular requirements - Floodlights
SANS 60614-1 Conduits for electrical installations – Specification Part 1: General requirements
SANS 61058-1 Switches for appliances Part 1: General requirements
SANS 61241-0 Electrical apparatus for use in the presence of combustible dust Part 0: General
requirements
SANS 61084-2-1 Cable trunking and ducting systems for electrical installations Part 2: Particular
requirements Section 1: Cable trunking and ducting systems intended for mounting on
wall or ceiling
SANS 61241-1 Electrical apparatus for use in the presence of combustible dust Part 1: Protection by
enclosures “tD”
SANS 868-1-1 Compression-ignition engine systems and machines powered by such engine systems
for use in mines and plants with explosive gas atmospheres or explosive dust
atmospheres or both Part 1-1: Hazardous locations in underground mines - Basic
explosion protected
EAC 22 NACE – DM 34,35.2,5 OTHER TRANSPORT EQUIPMENT
SANS 1116-2 Retro-reflective number plates for motor vehicles Part 2: Number plates (aluminium)
SANS 1116-4 Retro-reflective number plates for motor vehicles Part 4: Number plates (plastics)
SANS 1186-1 Symbolic safety signs Part 1: Standard signs and general requirements
SANS 1186-5 Symbolic safety signs Part 5: Photoluminescent signs
SANS 1193 Safety glass for vehicles – Toughened safety glass for vehicles
SANS 1329-4 Retro-reflective and fluorescent warming signs for road vehicles Part 4: Retro-reflective
chevron signs
Ball type couplings and towing brackets for towing caravans and light trailers Part 1:
towing brackets and integrated towing devices
Original Date of Accreditation: 01 May 2002 Page 6 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
CAPE TOWN SCOPE
STANDARD PRODUCT
EAC – 3 NACE – DA FOOD PRODUCTS, BEVERAGES AND TOBACCO
SANS 1657 Bottled water of subterranean origin
SANS 449 The manufacture of soft drinks and drink concentrates
SANS 587 Canned fish, canned marine molluscs and canned crustaceans and products derived
therefrom
EAC – 4 NACE DB TEXTILES AND TEXTILE PRODUCTS
SANS 1118-3 School clothing Part 3: Trousers and shorts
SANS 1118-4 School clothing Part 4: Shirts
SANS 1118-6 School clothing Part 6: Dresses, tunic and gyms
SANS 1118-7 School clothing Part 7: Girls slacks and skirts
SANS 1362 Sewing threads
SANS 1703 Shade netting
SANS 434 Boiler suits and workwear suits
SANS 985 Polyester-and-wool uniform fabrics
EAC – 5 NACE DC LEATHER AND LEATHER PRODUCTS
SANS 421 The production of men’s shoes (Goodyear welted with stitched or stuck-on outer soles)
EAC – 12 NACE DG CHEMICALS, CHEMICAL PRODUCTS AND FIBRES
SANS 1042 Polymer floor dressings
SANS 1044 Industrial laundry detergents
SANS 1216 Solvent-emulsion degreasers
SANS 1224 Polish stripper
SANS 1225 Ammoniated liquid detergent cleaner
SANS 1330 Waterless hand cleaners
SANS 1344 Medium duty solvent detergent
SANS 1586 Emulsion paints
SANS 1598 Unleaded petrol
SANS 1796 Application of durable organic powder coatings for architectural aluminium
SANS 1827 The safety of water treatment chemicals for use in the food industry
SANS 1828 Cleaning chemicals for use in the food industry
SANS 1853 Disinfectants and detergent-disinfectants for use in the food industry
SANS 309 Anionic bitumen road emulsions
SANS 342 Automotive diesel fuel
SANS 515 Decorative paint for interior use
SANS 548 Cationic bitumen road emulsions
SANS 630 Decorative high gloss enamel paints
SANS 731-1 Road markings Part 1: Single-pack solvent-borne paints
SANS 825 Hand dishwashing and light duty detergent (liquid)
Original Date of Accreditation: 01 May 2002 Page 7 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
CAPE TOWN SCOPE
STANDARD PRODUCT
EAC – 13 NACE - DG PHARMACEUTICALS
SANS 116 Liquid antiseptics containing substituted phenolics
SANS 1196 Detergent-disinfectants based on organic halogen compounds (other than iodine
compounds), such as fluorine, bromine or chlorine
SANS 296 Sodium hypochlorite solutions
SANS 47 Coal-tar type disinfectant liquids (black and white)
SANS 636 Disinfectants based on quaternary ammonium compounds
SANS 639 Detergent-disinfectants based on quaternary ammonium compounds
EAC 14 NACE DH RUBBER AND PLASTIC PRODUCTS
SANS 11 Unplasticized poly(vinyl chloride) (PVC-U) components for external rainwater systems
SANS 1291-2 Flexible polyurethane foam sleeping mats and mattresses Part 2: Foam mattresses
for domestic and hotel use
SANS 1494 Mobile refuse bins
SANS 1609 Structured wall pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) for buried
drainage and sewerage systems
SANS 20109 Uniform provisions concerning the approval for the production of retreaded pneumatic
tyres for commercial vehicles and their trailers
SANS 4047 Natural latex rubber condoms - Requirements and test methods
SANS 4427 Polyethylene (PE) pipes for water supply - Specifications
SANS 791 Unplasticized poly(vinyl chloride) (PVC-U) sewer and drain pipes and pipe fittings
SANS 966-1 Components of pressure pipe systems Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
pressure pipe systems
SANS 966-2 Components of pressure pipe systems Part 2: Modified poly(vinyl chloride) (PVC- M)
pressure pipe systems
SANS 967 Unplasticized poly(vinyl chloride) (PVC-U) soil, waste and vent pipes and pipe fittings
EAC – 16 NACE DI CONCRETE, CEMENT, LIME, PLASTER ETC
SANS 1215 Concrete masonry units
SANS 1263-1 Safety and security glazing materials for buildings Part 1: Safety performance of glazing
materials under human impact
SANS 1294 Precast concrete manhole sections and components
SANS 1381-6 Materials for thermal insulation of buildings Part 6: Cellulose loose fill thermal insulation
material
SANS 1575 Burnt clay paving units
SANS 1882 Polymer concrete surface boxes, manhole and inspection covers, gully gratings and
frames
SANS 227 Burnt clay masonry units
SANS 470 Concrete poles for telephone, power and lighting purposes
SANS 50197-1 Cement Part 1: Composition, specifications and conformity criteria for common cements
SANS 523 Limes for use in building
SANS 542 Concrete roofing tiles
SANS 676 Reinforced concrete pressure pipes
Original Date of Accreditation: 01 May 2002 Page 8 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
CAPE TOWN SCOPE
STANDARD PRODUCT
EAC – 16 NACE DI CONCRETE, CEMENT, LIME, PLASTER ECT
SANS 677 Concrete non-pressure pipes
SANS 824 Lime for soil stabilization
SANS 986 Precast reinforced concrete culverts
EAC – 17 NACE DJ BASIC METAL AND FABRICATED METAL PRODUCTS
SANS 1005 Innerspring mattresses
SANS 1062 Pressure and vacuum gauges
SANS 121 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test
methods
SANS 1219 Hand hacksaw blades
SANS 1475-1 The production of reconditioned fire-fighting equipment Part 1: Portable and wheeled
(mobile) rechargeable fire extinguishers
SANS 1475-2 The production of reconditioned fire-fighting equipment Part 2: Fire hose reels and
above-ground hydrants
SANS 193 Fire-dampers
SANS 4 Locks, latches, and associated furniture for doors (Domestic Type)
SANS 543 Fire hose reels
SANS 751 Burglar-resistant safes
SANS 920 Steel bars for concrete reinforcement
SANS 949 Strongroom and vault doors
SANS 953-1 Storage of firearms and ammunition Part 1: Safes
SANS 999 Anodized coatings on aluminium (for architectural applications)
EAC – 19 NACE DC ELECTRICAL AND OPTICAL EQUIPMENT/ELECTRONIC COMPONENTS
SANS 1020 Power-operated dispensing devices for flammable liquid fuels
SANS 1507-3 Electric cables with extruded solid dielectric insulation for fixed installations
(300/500 V to 1 900/3 300 V) Part 3: PVC Distribution cables
SANS 151 Fixed electric storage water heaters
SANS 1524-1 Electricity payment systems Part 1: Prepayment meters
SANS 181 Thermostats for electric storage water heaters
SANS 186 Energy regulators for electric heating units
SANS 514 Immersion heaters for electric storage water heaters
SANS 537 Oven thermostats for electric stoves
SANS 60079-0 Explosive atmospheres Part 0: Equipment - General requirements
SANS 60079-1 Explosive atmospheres Part 1: Equipment protection by flameproof enclosures "d"
SANS 60079-15 Explosive atmospheres Part 15: Equipment protection by type of protection "n"
SANS 60335-2-30 Household and similar electrical appliances - Safety Part 2-30: Particular requirements
for room heaters
SANS 60598-2-1 Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires
SANS 60598-2-2 Luminaires Part 2: Particular requirements Section 2: Recessed luminaires
SANS 60614-2-2 Specification for conduits for electrical installations Part 2: Particular specification for
conduits Section 2: Rigid plain conduits of insulating materials
Original Date of Accreditation: 01 May 2002 Page 9 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
CAPE TOWN SCOPE
STANDARD PRODUCT
EAC – 19 NACE DC ELECTRICAL AND OPTICAL EQUIPMENT/ELECTRONIC COMPONENTS
SANS 61643-1 Low-voltage surge protective devices Part 1: Surge protective devices connected to
low-voltage power distribution systems - Requirements and tests
SANS 62052-11 Electricity metering equipment (a.c.) - General requirements, tests and test conditions
Part 11: Metering equipment
SANS 755 Mineral-insulated metal-sheathed air-heating units for appliances
SANS 780 Distribution transformers
AEC – 22 NACE DM OTHER TRANSPORT EQUIPMENT
SANS 1080 Restraining devices (safety belts) for occupants of adult build in motor vehicles
(revised requirements)
SANS 1116-2 Retro-reflective number plates for motor vehicles Part 2: Number plates (aluminium)
SANS 1116-4 Retro-reflective number plates for motor vehicles Part 4: Number plates (plastics)
SANS 1186-1 Symbolic safety signs Part 1: Standard signs and general requirements
SANS 1186-5 Symbolic safety signs Part 5: Photoluminescent signs
SANS 192 Laminated safety glass for vehicles
SANS 193 Toughened safety glass for vehicles
Original Date of Accreditation: 01 May 2002 Page 10 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC – 4 NACE DC FOOD PRODUCTS, BEVERAGES AND TOBACCOS
SANS 1657 Bottled natural water
SANS 1657 Bottled natural water of subterranean origin
SANS 1678 Sterilized milk
SANS 1679 Pasteurized milk
SANS 1862 Packaged water other than natural mineral water
SANS 449 The manufacture of soft drinks and soft drink concentrates
SANS 49 Edible gelatin
EAC – 4 NACE DB TEXTILE AND TEXTILE PRODUCTS
SANS 1703 Shade netting
SANS 434 Boiler suits and workwear suits
SANS 94-1 Textile slings – Safety Part 1: Flat woven webbing slings, made of man-made fibres, for
general purpose use
SANS 94-2 Textile slings – Safety Part 2: Roundslings made of man-made fibres for purpose use
AEC – 5 NACE DB TEXTILE AND TEXTILE PRODUCTS
SANS 20345 Personal protective equipment - Safety footwear
SANS 421 The production of men's shoes (Goodyear welted with stitched or stuck-on outer soles)
SANS 741 Industrial boots (including safety boots) with direct-vulcanized soles and heels
SANS 942 Children's, youths', and maids' school shoes with direct injection-moulded soles and heels
EAC – 6 NACE DD WOOD AND WOOD PRODUCTS
SANS 1783-1 Sawn softwood timber Part 1: General requirements
SANS 1783-2 Sawn softwood timber Part 2: Stress-graded structural timber and timber for frame wall
construction
SANS 1783-3 Sawn softwood timber Part 3: Industrial timber
SANS 1783-4 Sawn softwood timber Part 4: Brandering and battens
SANS 1900 Monoplanar prefabricated timber roof trusses (nail-plated)
SANS 457-2 Wooden poles, droppers, guardrail posts and spacer blocks Part 2: Softwood species
SANS 457-3 Wooden poles, droppers, guardrail posts and spacer blocks Part 3: Hardwood species
SANS 545 Wooden doors
SANS 660 Classroom furniture
SANS 753 Pine poles, cross-arms and spacers for power distribution, telephone systems and street
lighting
SANS 754 Eucalyptus poles, cross-arms and spacers for power distribution and communications
systems
SANS 929 Plywood and composite board
EAC – 12 NACE – DF 23.1, 2 MANUFACTURER OF COKE AND REFINED PETROLEUM PRODUCTS
SANS 616 Wood-preserving creosote mixtures and coal-tar mixture
Original Date of Accreditation: 01 May 2002 Page 11 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC – 12 NACE – DG minus 24.4 CHEMICAL PRODUCTS AND FIBRES
SANS 630 Decorative high gloss enamel paints
SANS 650 Laundry detergent (for use in non-automatic domestic washing machines)
SANS 651 Low-foam laundry detergent (for use in automatic and non-automatic domestic washing
machines)
SANS 680 Glazing putty for wooden and metal window frames
SANS 681 Undercoats for paints
SANS 731-1 Road markings Part 1: Single-pack solvent-borne paints
SANS 825 Hand dishwashing and light duty detergent (liquid)
SANS 892 General purpose detergent (beads, granules and powders)
SANS 940 Emulsion roof paint
EAC – 13 NACE – DG 24.4 PHARMACEUTICALS
SANS 636 Disinfectants based on quaternary ammonium compounds
SANS 639 Detergent-disinfectants based on quaternary ammonium compounds
SANS 643 Disinfectants based on stabilized inorganic chlorine compounds
SANS
EAC – 14 NACE - DH RUBBER AND PLASTIC PRODUCTS
SANS 786 Flexible vinyl flooring
SANS 791 Unplasticized poly(vinyl chloride) (PVC-U) sewer and drain pipes and pipe fittings
SANS 808 Cable glands for use on flameproof enclosures (Ex d)
SANS 950 Unplasticized polyvinyl chloride rigid conduit and fittings for use in electrical installations
SANS 952 Polyolefin film for damp- and waterproofing in buildings
SANS 966-1 Components of pressure pipe systems Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
pressure pipe systems
SANS 966-2 Components of pressure pipe systems Part 2: Modified poly(vinyl chloride) (PVC-M)
pressure pipe systems
SANS 967 Unplasticized poly(vinyl chloride) (PVC-U) soil, waste and vent pipes and pipe fittings
SANS 971 Fire-retardant textile-reinforced conveyor belting (for use in fiery mines)
EAC – 15 NACE – Di minus 26.5,6 NON METALLIC MINERAL PRODUCTS
SANS 141 Glass-reinforced polyester (GRP) laminates
SANS 15875-5 Plastics piping systems for hot and cold water installations - Crosslinked polyethylene
(PE-X) Part 5: Fitness for purpose of the system
SANS 1748-1 Glass-fibre-reinforced thermosetting plastics (GRP) pipes Part 1: Pipes for water supply,
sewerage and drainage
SANS 1749 Glass-reinforced polyester (GRP) poles
Original Date of Accreditation: 01 May 2002 Page 12 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC – 1 6 NACE – Di 26.5 &6 CONCRETE, CEMENT, LIME, PLASTER ETC
SANS 1022 Metal roofing tiles
SANS 1215 Concrete masonry units
SANS 1263-1 Safety and security glazing materials for buildings Part 1: Safety performance of glazing
materials under human impact
SANS 1263-2 Safety and security glazing materials for buildings Part 2: Burglar-resistant and
vandal-resistant glazing materials
SANS 1263-3 Safety and security glazing materials for buildings Part 3: Bullet-resistant glazing materials
SANS 1294 Precast concrete manhole sections and components
SANS 1381-1 Materials for thermal insulation of buildings Part 1: Fibre thermal insulation mats
SANS 1491-1 Portland cement extenders Part 1: Ground granulated blastfurnace slag
SANS 1491-2 Portland cement extenders Part 2: Fly ash
SANS 1575 Burnt clay paving units
SANS 15876-1 Plastics piping systems for hot and cold water installations - Polybutylene (PB)
Part 1: General
SANS 1879 Precast concrete suspended slabs
SANS 1882 Polymer concrete surface boxes, manhole and inspection covers, gully gratings and
frames
SANS 227 Burnt clay masonry units
SANS 470 Concrete poles for telephone, power and lighting purposes
SANS 50197-1 Cement Part 1: Composition, specifications and conformity criteria for common cements
SANS 50413-1 Masonry cement Part 1: Composition, specifications and conformity criteria
SANS 508 Concrete retaining blocks
SANS 523 Limes for use in building
SANS 540-1 Fibreboard products Part 1: Uncoated fibreboard
SANS 540-2 Fibreboard products Part 2: Coated fibreboard
SANS 542 Concrete roofing tiles
SANS 676 Reinforced concrete pressure pipes
SANS 677 Concrete non-pressure pipes
SANS 685 Fibre-cement sheets (flat and profiled)
SANS 803 Fibre-cement boards
SANS 819 Fibre-cement pipes, couplings and fittings for sewerage, drainage and low- pressure
irrigation
SANS 824 Lime for soil stabilization
SANS 927 Precast concrete kerbs, edgings and channels
SANS 986 Precast reinforced concrete culverts
SANS 9933 Products in fibre-reinforced cement - Long corrugated or asymmetrical section sheets
and fittings for roofing and cladding
EAC – 17 NACE DJ 27, 28 BASIC METALS AND FABRICATED METAL PRODUCTS
SANS 1005 Innerspring mattresses
SANS 101 White metal designated WM 6
SANS 10131 Above-ground storage tanks for petroleum products
Original Date of Accreditation: 01 May 2002 Page 13 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC – 17 NACE – DJ 27, 28 BASIC METALS AND FABRICATED METAL PRODUCTS
SANS 102 White metal designated WM 15
SANS 1024 Welded steel fabric for reinforcement of concrete
SANS 10244-2 Steel wire and wire products - Non-ferrous metallic coatings on steel wire Part 2: Zinc and
zinc alloy coatings
SANS 1026 Bench vices for metal work (Metric units)
SANS 103 White metal designated WM 30
SANS 1034 Grey iron castings
SANS 104 White metal designated WM 40
SANS 1056-2 Ballvalves Part 2: Heavy duty valves (not fire-safe)
SANS 1056-3 Ballvalves Part 3: Light duty valves (not fire-safe)
SANS 106 White metal designated WM 66
SANS 1060 Wheelchairs (folding type)
SANS 1062 Pressure and vacuum gauges
SANS 1063 Earth rods, couplers and connections
SANS 1067-1 Copper-based fittings for copper tubes Part 1: Compression fittings
SANS 1067-2 Copper-based fittings for copper tubes Part 2: Capillary solder fittings
SANS 107 White metal designated WM 72
SANS 108 White metal designated WM 80
SANS 109 White metal designated WM 84
SANS 1115 Cast iron gratings for gullies and stormwater drains
SANS 1120 Pliers and nippers
SANS 1128-1 Firefighting equipment Part 1: Components of underground and above-ground hydrant
systems
SANS 1151 Portable rechargeable fire extinguishers - Halogenated hydrocarbon type extinguishers
SANS 1160-1 Wheeled fire extinguishers - Performance and construction
SANS 1172 Files and rasps
SANS 1182 Light gauge welded steel pipes
SANS 121 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test
methods
SANS 12277 Mountaineering equipment - Harnesses - Safety requirements and test methods
SANS 124 White metal designated WM 90
SANS 1240 Automatic shut-off flush valves for water closets and urinals
SANS 1253 Fire-doors and fire-shutters
SANS 1313-1 Conveyor belt idlers Part 1: Troughed belt conveyor idlers (metallic and non-metallic)
for belt speeds of up to 5,0 m/s
SANS 1350 Guardrails for roads (W-section)
SANS 137 Resin cored solders (non-corrosive)
SANS 138 Resin cored solders (highly activated)
SANS 1397 Industrial safety helmets
SANS 14 Malleable cast iron fittings threaded to ISO 7-1
Original Date of Accreditation: 01 May 2002 Page 14 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC – 17 NACE – DJ 27, 28 BASIC METALS AND FABRICATED METAL PRODUCTS
SANS 1407 Anodized coatings on aluminium (for general applications)
SANS 1409 Outlet sockets and probes for medical (gas and vacuum) services used in hospitals
SANS 1431 Weldable structural steels
SANS 14341 Welding consumables - Wire electrodes and deposits for gas shielded metal arc welding
of non alloy and fine grain steels - Classification
SANS 1451-2 Hearing protectors Part 2: Ear-plugs
SANS 14520-1 Gaseous fire-extinguishing systems - Physical properties and system design Part 1:
General requirements
SANS 14520-14 Gaseous fire-extinguishing systems - Physical properties and system design Part 14:
IG-55 extinguishant
SANS 14520-9 Gaseous fire-extinguishing systems - Physical properties and system design Part 9:
HFC 227ea extinguishant
SANS 1453 Copper tubes for medical gas and vacuum services
SANS 1475-1 The production of reconditioned fire-fighting equipment Part 1: Portable and wheeled
(mobile) rechargeable fire extinguishers
SANS 1475-2 The production of reconditioned fire-fighting equipment Part 2: Fire hose reels and
above-ground hydrants
SANS 1480 Single control mixer taps
SANS 1509 Flush valves for WC flushing cisterns
SANS 1532 Vent valves for drainage installations
SANS 1533 Padlocks
SANS 1535 Glass-reinforced polyester-coated steel tanks for the underground storage of
hydrocarbons and oxygenated solvents and intended for burial horizontally
SANS 1539 Appliances operating on liquefied petroleum gas - Safety aspects
SANS 1551-1 Check valves (flanged and wafer types) Part 1: PN series
SANS 1567 Portable rechargeable fire extinguishers - CO2 type extinguishers
SANS 15876-2 Plastics piping systems for hot and cold water installations - Polybutylene (PB) Part 2:
Pipes
SANS 1592 Short-link steel chain (close-tolerance) for lifting appliances
SANS 1594 Manually operated chain blocks
SANS 1595 Forged steel lifting hooks for use with steel chains of strength grade M(4), P(5), S(6),
T(8) and V(10)
SANS 1636 Manually operated chain lever hoists
SANS 1655 Welding of thermoplastics - Welding rods, fillers and solvents
SANS 1808-16 Water supply and distribution system components Part 16: Drinking fountains
SANS 1808-2 Water supply and distribution system components Part 2: Metallic compression type pipe
couplings
SANS 1808-35 Water supply and distribution system components Part 35: Electronically operated taps
and valves
SANS 1808-44 Water supply and distribution system components Part 44: Pipe saddles
SANS 1808-5 Water supply and distribution system components Part 5: Flexible connectors
SANS 1808-53 Water supply and distribution system components Part 53: Drain cocks for hot-water
storage containers
Original Date of Accreditation: 01 May 2002 Page 15 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC – 17 NACE – DJ 27,28 BASIC METALS AND FABRICATED METAL PRODUCTS
SANS 1808-66 Water supply and distribution system components Part 66: Demand type water taps
SANS 1808-9 Water supply and distribution system components Part 9: Metering taps and valves
(metallic bodies)
SANS 1845 Prefinished sheet metal products for interior and exterior building applications
SANS 1849 Butterfly valves for general purposes
SANS 189 Short-link steel chain (medium-tolerance) for lifting purposes
SANS 1906 Non-pressure paraffin stoves and heaters
SANS 191 Cast steel gate valves
SANS 1910 Portable refillable fire extinguishers
SANS 193 Fire-dampers
SANS 198 Functional-control valves and safety valves for domestic hot and cold water supply
systems
SANS 199 Shut-off valves for refillable liquefied petroleum gas cylinders
SANS 2081 Metallic coatings - Electroplated coatings of zinc on iron or steel
SANS 226 Water taps (metallic bodies)
SANS 24 Soft solders
SANS 2503 Gas welding equipment - Pressure regulators for gas cylinders used in welding, cutting
and allied processes up to 300 bar
SANS 251 Long-link and extra-long-link medium tolerance steel chains for general purposes
SANS 2560 Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and
fine grain steels - Classification
SANS 284 Spades and shovels
SANS 29 Articles made of precious metals
SANS 32 Internal and/or external protective coatings for steel tubes - Specification for hot dip
galvanized coatings applied in automatic plants
SANS 3310-1 Test sieves - Technical requirements and testing Part 1: Test sieves of metal wire cloth
SANS 3310-2 Test sieves - Technical requirements and testing Part 2: Test sieves of perforated metal
plate
SANS 343 Steel bedside lockers
SANS 3581 Welding consumables - Covered electrodes for manual metal arc welding of stainless and
heat-resisting steels - Classification
SANS 387 Hammer heads and hand hammers
SANS 39 Small medical gas cylinders - Pin-index yoke-type valve connections
SANS 390 Forks and rakes
SANS 4 Locks, latches, and associated furniture for doors (Domestic Type)
SANS 407 Austenitic manganese steel castings
SANS 455 Covered electrodes for the manual arc welding of carbon and carbon manganese steels
SANS 460 Plain-ended solid drawn copper tubes for potable water
SANS 4706 Refillable welded steel gas cylinders
SANS 4778 Chain slings of welded construction - Grades M(4), S(6) and T(8)
SANS 497 Glazed ceramic sanitaryware
Original Date of Accreditation: 01 May 2002 Page 16 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC – 17 NACE – DJ 27,28 BASIC METALS AND FABRICATED METAL PRODUCTS
SANS 50124 Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements,
type testing, marking, quality control
SANS 50149 Respiratory protective devices - Filtering half masks to protect against particles -
Requirements, testing, marking
SANS 50353-1 Personal protective equipment against falls from a height - Guided type fall arresters
including a rigid anchor line
SANS 50354 Personal protective equipment against falls from a height - Lanyards
SANS 50355 Personal protective equipment against falls from a height - Energy absorbers
SANS 50358 Personal protective equipment for work positioning and prevention of falls from a height -
Belts for work positioning and restraint and work positioning lanyards
SANS 50361 Personal protective equipment against falls from a height - Full body harnesses
SANS 50440 Welding consumables - Wire electrodes and deposits for gas shielded metal arc welding
of non alloy and fine grain steels - Classification
SANS 50566 Mountaineering equipment - Slings - Safety requirements and test methods
SANS 50730-1 Gas welding equipment - Safety devices Part 1: Incorporating a flame (flashback) arrestor
SANS 50795 Protection against falls from a height - Anchor devices - Requirements and testing
SANS 50813 Personal protective equipment for prevention of falls from a height - Sit harnesses
SANS 51317-1 Road restraint systems Part 1: Terminology and general criteria for test methods
SANS 51317-2 Road restraint systems Part 2: Performance classes, impact test acceptance criteria and
test methods for safety barriers
SANS 521 Hospital beds and cots
SANS 52842 Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
SANS 53811 Sherardizing - Zinc diffusion coatings on ferrous products – Specification
EAC – 18 NACE MACHINERY AND EQUIPMENT
SANS 15876-3 Plastic piping systems for hot and cold water installations – Polybutylene (PB)
Part 3: Fittings
EAC – 19 NACE – DL MINUS 32.1 & DK 29.7
ELECTRICAL AND OPTICAL, DOMESTIC APPLIANCES
SANS 1213 Electric light dimmers (Metric units)
SANS 1239 Power-operated dispensing devices for flammable liquid fuels
SANS 1266 Mechanical cable glands
SANS 1339 Plugs, socket-outlets and couplers for industrial purposes
SANS 1376-2 Ballasts for discharge lamps (excluding tubular fluorescent lamps)
SANS 1376-3 Electric cables - Cross-linked polyethylene (XLPE) insulated cables for rated voltages
3,8/6,6 kV to19/33 kV
SANS 1418-1 Lights for motor vehicles Part 2: Headlights
SANS 1418-2 Lights for motor vehicles Part 3: Secondary lights
SANS 1438-3 Aerial bundled conductor systems Part 1: Cores
SANS 1464-22 Aerial bundled conductor systems Part 2: Assembled insulated conductor bundles
SANS 1489 Helmet light assemblies for miners Part 3: Cables
Original Date of Accreditation: 01 May 2002 Page 17 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC -19 NACE – DL MINUS 32.1 & DK 29.7
ELECTRICAL AND OPTICAL EQUIPMENT, DOMESTIC APPLIANCES
SANS 1507-1 Safety of luminaires Part 22: Luminaires for emergency lighting
SANS 1507-2 Flameproof restrained and bolted type plugs and sockets
SANS 1507-3 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to
1 900/3300 V) Part 1: General
SANS 1507-4 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to
1 900/3300 V) Part 2: Wiring cables
SANS 1507-5 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to
1 900/3300 V) Part 3: PVC distribution cables
SANS 1507-6 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to
1 900/3300 V) Part 4: XLPE distribution cables
SANS 151 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to
1 900/3300 V) Part 5: Halogen-free distribution cables
SANS 1520-1 Electric cables with extruded solid dielectric insulation for fixed installations (300/500 V to
1 900/3300 V) Part 6: Service cables
SANS 1520-2 Fixed electric storage water heaters
SANS 1524-1 Flexible electric trailing cables for use in mines Part 1: Low-voltage (640/1 100 V and 1
900/3 300 V) cables
SANS 1561-1 Flexible electric trailing cables for use in mines Part 2: High-voltage (3,8/6,6 kV to 19/33
kV) cables
SANS 1574-1 Electricity payment systems Part 1: Prepayment meters
SANS 1574-3 Rewound and refurbished rotating electrical machines Part 1: Low-voltage three-phase
induction motors
SANS 1574-4 Electric flexible cores, cords and cables with solid extruded dielectric insulation Part 1:
General
SANS 1574-5 Electric flexible cores, cords and cables with solid extruded dielectric insulation Part 3:
PVC- insulated cores and cables
SANS 1576 Electric flexible cables with solid extruded dielectric insulation Part 4: Rubber-insulated
cores and cords
SANS 15876-5 Electric flexible cables with solid extruded dielectric insulation Part 5: Rubber-insulated
cores and cables
SANS 164-0 Electric cables - Single core arc welding cable
SANS 60335-2-7 Household and similar electrical appliances - Safety Part 2-7: Particular requirements for
washing machines
SANS 60335-2-75 Household and similar electrical appliances - Safety Part 2-75: Particular requirements for
commercial dispensing appliances and vending machines
SANS 60335-2-80 Safety of household and similar electrical appliances Part 2-80: Particular requirements for
fans
SANS 60432-3 Incandescent lamps - Safety specifications Part 3: Tungsten-halogen lamps (non-vehicle)
SANS 60529 Degrees of protection provided by enclosures (IP Code)
SANS 60598-2-1 Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires
Original Date of Accreditation: 01 May 2002 Page 18 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC 19 – NACE – DL MINUS 32.1 & 29.7
ELECTRICAL AND OPTICAL EQUIPMENT, DOMESTIC APPLIANCES
SANS 60598-2- Luminaires Part 2: Particular requirements Section 2: Recessed luminaires
SANS 60598-2-20 Luminaires Part 2-20: Particular requirements - Lighting chains
SANS 60598-2-23 Luminaires Part 2-23: Particular requirements - Extra low voltage lighting systems for
filament lamps
SANS 60598-2-25 Luminaires Part 2-25: Particular requirements - Luminaires for use in clinical areas of
hospitals and health care buildings
SANS 60598-2-3 Luminaires Part 2-3: Particular requirements - Luminaires for road and street lighting
SANS 60598-2-4 Luminaires Part 2: Particular requirements Section 4: Portable general purpose luminaires
SANS 60598-2-5 Luminaires Part 2-5: Particular requirements - Floodlights
SANS 60598-2-6 Luminaires Part 2: Particular requirements Section 6: Luminaires with built-in transformers
or convertors for filament lamps
SANS 60598-2-7 Luminaires Part 2: Particular requirements Section 7: Portable luminaires for garden use
SANS 60598-2-8 Luminaires Part 2-8: Particular requirements - Handlamps
SANS 60614-1 Conduits for electrical installations - Specification Part 1: General requirements
SANS 60614-2-2 Specification for conduits for electrical installations Part 2: Particular specification for
conduits Section 2: Rigid plain conduits of insulating materials
SANS 60669-1 Switches for household and similar fixed-electrical installations Part 1: General
requirements
SANS 60669-2-1 Switches for household and similar fixed electrical installations Part 2-1: Particular
requirements - Electronic switches
SANS 60670-1 Boxes and enclosures for electrical accessories for household and similar fixed electrical
installations Part 1: General requirements
SANS 60670-24 Boxes and enclosures for electrical accessories for household and similar fixed electrical
installations Part 24: Particular requirements for enclosures for housing protective devices
and similar power consuming devices
SANS 60730-2-9 Automatic electrical controls for household and similar use Part 2-9: Particular
requirements for temperature sensing controls
SANS 60794-4 Optical fibre cables Part 4: Sectional specification - Aerial optical cables along electrical
power lines
SANS 60799 Electrical accessories - Cord sets and interconnection cord sets
SANS 60884-2-5 Plugs and socket-outlets for household and similar purposes Part 2-5: Particular
requirements for adaptors
SANS 60901 Single-capped fluorescent lamps - Performance specifications
SANS 60947-3 Low-voltage switchgear and controlgear Part 3: Switches, disconnectors, switch-
disconnectors and fuse- combination units
SANS 60968 Self-ballasted lamps for general lighting services - Safety requirements
SANS 60969 Self-ballasted lamps for general lighting services - Performance requirements
SANS 61048 Auxiliaries for lamps - Capacitors for use in tubular fluorescent and other discharge lamp
circuits - General and safety requirements
Original Date of Accreditation: 01 May 2002 Page 19 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIA SCOPE
STANDARD PRODUCT
EAC 19 – NACE DL MINUS 32.1 & 29.7
ELECTRICAL AND OPTICAL EQUIPMENT, DOMESTIC APPLIANCES
SANS 61084-1 Cable trunking and ducting systems for electrical installations Part 1: General
requirements
SANS 61084-2-1 Cable trunking and ducting systems for electrical installations Part 2: Particular
requirements Section 1: Cable trunking and ducting systems intended for mounting on
walls or ceilings
SANS 61199 Single-capped fluorescent lamps - Safety specifications
SANS 61241-0 Electrical apparatus for use in the presence of combustible dust Part 0: General
requirements
SANS 61241-1 Electrical apparatus for use in the presence of combustible dust Part 1: Protection by
enclosures "tD"
SANS 61243-1 Live working - Voltage detectors Part 1: Capacitive type to be used for voltages
exceeding 1 kV a.c.
SANS 61347-2-1 Lamp controlgear Part 2-1: Particular requirements for starting devices (other than glow
starters)
SANS 61347-2-2 Lamp controlgear Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-
down convertors for filament lamps
SANS 61347-2-3 Lamp controlgear Part 2-3: Particular requirements for a.c supplied electronic ballasts for
fluorescent lamps
SANS 61347-2-8 Lamp controlgear Part 2-8: Particular requirements for ballasts for fluorescent lamps
SANS 61347-2-9 Lamp controlgear Part 2-9: Particular requirements for ballasts for discharge lamps
(excluding fluorescent lamps)
SANS 61481 Live working - Portable phase comparators for use on voltages from 1 kV to 36 kV a.c.
SANS 61558-2-5 Safety of power transformers, power supply units and similar Part 2-5: Particular
requirements for shaver transformers and shaver supply units
SANS 61558-2-6 Safety of power transformers, power supply units and similar Part 2-6: Particular
requirements for safety isolating transformers for general use
SANS 61643-1 Low-voltage surge protective devices Part 1: Surge protective devices connected to low-
voltage power distribution systems - Requirements and tests
SANS 767-1 Earth leakage protection units Part 1: Fixed earth leakage protection circuit-breakers
SANS 780 Distribution transformers
SANS 868-1-1 Compression-ignition engine systems and machines powered by such engine systems, for
use in mines and plants with explosive gas atmospheres or explosive dust atmospheres or
both Part 1-1:Hazardous locations in underground mines - Basic explosion protected
SANS 868-1-3 Compression-ignition engine systems and machines powered by such engine systems, for
use in mines and plants with explosive gas atmospheres or explosive dust atmospheres or
both Part 1-3: Hazardous locations in underground mines - Machines
SANS 890-1 Ballasts for fluorescent lamps Part 1: Ballasts for lamps for operation with starters (class A
lamps)
SANS 97 Electric cables - Impregnated paper-insulated metal-sheathed cables for rated voltages
3,3/3,3kV to 19/33 kV (excluding pressure assisted cables)
Original Date of Accreditation: 01 May 2002 Page 20 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PRETORIASCOPE
STANDARD PRODUCT
EAC – 22 NACE –DM 34.4 TRANSPORT EQUIPMENT
SANS 1329-4 Retro-reflective and fluorescent warning signs for road vehicles Part 4: Retro-reflective
chevron signs
SANS 1329-5 Retro-reflective and fluorescent warning signs for road vehicles Part 5: Retro-reflective
chevron decals
SANS 1017 Electric cables for motor vehicles - Low-voltage cables and flexible earthing straps for
motor vehicles
SANS 1080 Restraining devices (safety belts) for occupants of adult build in motor vehicles (revised
requirements)
SANS 1116-1 Retro-reflective registration plates for motor vehicles Part 1: Blanks (metal)
SANS 1116-2 Retro-reflective number plates for motor vehicles Part 2: Number plates (aluminium)
SANS 1116-4 Retro-reflective number plates for motor vehicles Part 4: Number plates (plastics)
SANS 1186-1 Symbolic safety signs Part 1: Standard signs and general requirements
SANS 1186-4 Symbolic safety signs Part 4: Retro-reflective signs
SANS 1186-5 Symbolic safety signs Part 5: Photoluminescent signs
SANS 1191 High penetration-resistant laminated safety glass for vehicles
SANS 1192 Laminated safety glass for vehicles
SANS 1193 Toughened safety glass for vehicles
SANS 1329-4 Retro-reflective and fluorescent warning signs for road vehicles Part 4: Retro-reflective
chevron signs
SANS 1329-5 Retro-reflective and fluorescent warning signs for road vehicles Part 5: Retro-reflective
chevron decals
SANS 1505-1 Ball type couplings and towing brackets for towing caravans and light trailers Part 1:
Towing brackets and integrated towing devices
SANS 1519-2 Road signs Part 2: Performance requirements for road signs
SANS 1622 New replacement brake drums for motor vehicles
SANS 20003 Uniform provisions concerning the approval of retro-reflective devices for power-driven
vehicles and their trailers
SANS 513 Retro-reflectors (reflex reflectors)
EAC – 23 NACE – DM 34.4
SANS 785 Writing equipment - Ballpoint pens
Original Date of Accreditation: 01 May 2002 Page 21 of 23
Field Manager
ANNEXURE A
Facility No.: C07a Date of Issue: 15 October 2013
Expiry Date: 30 December 2015
PORT ELIZABETH SCOPE
STANDARD PRODUCT
EAC – 3 NACE DA FOOD PRODUCTS, BEVERAGES AND TOBACCOS
SANS 449 The manufacture of soft drinks and soft drink concentrates
EAC – 4 NACE - DB TEXTILE AND TEXTILE PRODUCTS
SANS 1387-4 Woven cotton and similar apparel fabrics Part 4: Cotton jean and drill fabrics
SANS 1387-9 Woven cotton and similar apparel fabrics Part 9: Polyester-and-cotton shirt fabrics
SANS 1401-3 Woven cotton and similar household fabrics and articles Part 3: Cotton sheeting,
sheets, and pillowcases
SANS 316 Industrial hand protectors (leather and fabric) and leather protective clothing
SANS 434 Boiler suits and workwear suits
EAC – 12 NACE – DG minus 24.4 CHEMICALS, CHEMICAL PRODUCTS AND FIBRES
SANS 1381-4 Materials for thermal insulation of buildings Part 4: Reflective foil laminates (rolls,
sheets and sections)
SANS 1828 Cleaning chemicals for use in the food industry
SANS 1853 Disinfectants and detergent-disinfectants for use in the food industry
EAC -14 NACE - DH RUBBER AND PLASTIC PRODUCTS
SANS 1173 General purpose textile-reinforced conveyor belting
SANS 1366 Steel cord reinforced conveyor belting
SANS 1374 Toothbrushes
SANS 20109 Uniform provisions concerning the approval for the production of retreaded pneumatic
tyres for commercial vehicles and their trailers
SANS 4427 Polyethylene (PE) pipes for water supply - Specifications
SANS 581 Semi-flexible vinyl floor tiles
SANS 786 Flexible vinyl flooring
SANS 791 Unplasticized poly(vinyl chloride) (PVC-U) sewer and drain pipes and pipe fittings
SANS 952 Polyolefin film for damp- and waterproofing in buildings
SANS 966-1 Components of pressure pipe systems Part 1: Unplasticized poly(vinyl chloride)
(PVC-U) pressure pipe systems
SANS 967 Unplasticized poly(vinyl chloride) (PVC-U) soil, waste and vent pipes and pipe fittings
SANS 971 Conveyor belting - Fire-retardant properties for all construction types
EAC – 16 NACE – Di 26.5 & 6 CONCRETE, CEMENT, LIME, PLASTER ETC
SANS 1215 Concrete masonry units
SANS 1263-1 Safety and security glazing materials for buildings Part 1: Safety performance of glazing
materials under human impact
SANS 1294 Precast concrete manhole sections and components
SANS 542 Concrete roofing tiles
Original Date of Accreditation: 01 May 2002 Page 22 of 23
Field Manager
ANNEXURE A
Facility No.: C07a
Date of Issue: 15 October 2013 Expiry Date: 30 December 2015
PORT ELIZABETH SCOPE
STANDARD PRODUCT
EAC – 16 NACE Di 26.5 & 6 CONCTRETE, CEMENT, LIME PLASTER ECT
SANS 674 Steel-reinforced spirally wound PE drainage and sewer pipes
SANS 676 Reinforced concrete pressure pipes
SANS 677 Concrete non-pressure pipes
SANS 927 Precast concrete kerbs, edgings and channels
SANS 986 Precast reinforced concrete culverts
EAC – 19 – NACE – DL MINUS 32.1 & DK 29.7
ELECTRICAL AND OPTICAL EQUIPMENT, DOMESTIC APPLIANCES
SANS 1438-2 Helmet light assemblies for miners Part 2: Lead-acid batteries
SANS 1438-4 Helmet light assemblies for miners Part 4: Helmet lights (headlights)
SANS 1438-5 Helmet light assemblies for miners Part 5: Helmet light assemblies
SANS 475 Luminaires for interior lighting, streetlighting and floodlighting - Performance requirements
SANS 60598-2-1 Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires
SANS 60598-2-5 Luminaires Part 2-5: Particular requirements - Floodlights
SANS 60896-11 Stationary lead-acid batteries Part 11: Vented types - General requirements and methods
of test
SANS 60896-21 Stationary lead-acid batteries Part 21: Valve regulated types - Methods of test
SANS 60896-22 Stationary lead-acid batteries Part 22: Valve regulated types - Requirements
SANS 61084-1 Cable trunking and ducting systems for electrical installations Part 1: General
requirements
EAC – 22 NACE – DM 34.3 TRANSPORT EQUIPMENT
SANS 1116-2 Retro-reflective number plates for motor vehicles Part 2: Number plates (aluminium)
SANS 1116-4 Retro-reflective number plates for motor vehicles Part 4: Number plates (plastics)
SANS 1191 High penetration-resistant laminated safety glass for vehicles
SANS 1192 Laminated safety glass for vehicles
SANS 1193 Toughened safety glass for vehicles
SANS 2 Lead-acid starter batteries
SANS 50286-2 Simple unfired pressure vessels designed to contain air or nitrogen Part 2: Pressure
braking and auxiliary systems for motor vehicles and their trailers
SANS 60254-1 Lead-acid traction batteries Part 1: General requirements and methods of test
Original Date of Accreditation: 01 May 2002 Page 23 of 23
ISSUED BY THE SOUTH AFRICAN NATIONAL ACCREDITATION SYSTEM
Field Manager