TECHNICAL MANUAL
SAILOR SYSTEM 5000 GMDSS CONSOLE
Disclaimer
Any responsibility or liability for loss or damage in connection with the use of this product and theaccompanying documentation is disclaimed by Thrane & Thrane. The information in this manual isprovided for information purposes only, is subject to change without notice and may contain errors orinaccuracies.
Manuals issued by Thrane & Thrane are periodically revised and updated. Anyone relying on thisinformation should acquire the most current version e.g. from the Thrane & Thrane Extranet athttp://extranet.thrane.com.
Thrane & Thrane is not responsible for the content or accuracy of any translations or reproductions, inwhole or in part, of this manual from any other source.
0935
Console 5000
0930
CONTENTS
1 General information .......................................................................... 1-1
2 Installation ......................................................................................... 2-12.1 Dimensions.......................................................................................... 2-12.2 Drilling and cutting template ................................................................ 2-42.2.1 Tabletop mounting for 325mm and 400mm section ............................ 2-42.2.2 Tabletop mounting for 3 x 400mm section .......................................... 2-42.2.3 Bulkhead mounting for 325mm and 400mm section ........................... 2-52.2.4 Bulkhead mounting for 3 x 400mm section ......................................... 2-52.2.5 Earth stubs mounting .......................................................................... 2-62.2.6 Placement of print ............................................................................... 2-62.3 Mounting the console onto the bulkhead............................................. 2-72.4 Paper roll ............................................................................................. 2-92.5 Control units ........................................................................................ 2-92.6 Message terminal ................................................................................ 2-102.7 Factory configuration of the console ................................................... 2-11
3 Electrical installation ........................................................................ 3-13.1 TT-3606E opt. 003 NMEA Adapter for mini-C ..................................... 3-13.2 Grounding cables ................................................................................ 3-23.3 Console light........................................................................................ 3-33.4 Connection board ................................................................................ 3-43.5 Schematic connection board ............................................................... 3-5
4 Installation cables ............................................................................. 4-14.1 Console wiring system ........................................................................ 4-14.2 Internal cables overview ...................................................................... 4-24.2.1 Internal cables 2 section console w/ MF/HF Radiotelex, mini-C and VHF ....... 4-44.2.2 Internal cables 3 section console w/ MF/HF Radiotelex, mini-C and VHF ....... 4-54.2.3 Internal cables 3 section console w/ MF/HF, 2 x mini-C and VHF ...... 4-64.2.4 Internal cables 1 section console w/ MF/HF and VHF......................... 4-74.3 Installation external cabling ................................................................. 4-84.3.1 External cabling - Emergency light, Battery Panel and position source ........ 4-84.3.2 External cabling - Alarm Panel ............................................................ 4-94.3.3 External cabling - VHF ........................................................................ 4-94.3.4 External cabling - MF/HF..................................................................... 4-104.3.5 External cabling - mini-C and Power supply ........................................ 4-10
1 General information Console 5000
1-10815
1 General information
With the System 5000 GMDSS console, all the communication equipment of the ship can be combinedin one small, compact console.
One of the main purposes of the console is to make the best possible use of the limited space on boarda ship. Furthermore, the fact that all the equipment is kept in the same place makes installation easy andfast. Finally, the modular structure of the system means that it can easily be altered if for example a needto have it extended should arise.
The standard console includes the following: Emergency light, battery panel, and connection board.Furthermore, the console is designed with removable front plates for easy service and maintenance.
The console can be configured to match any maritime communication need. On the following pages,some typical configurations are shown.
1 General information Console 5000
1-2 0815
2 Installation Console 5000
2-10929
2 Installation
2.1 DimensionsConsole type numbers and part numbers refer to console hardware only, i.e. an empty console with only batterypanel, emergency light and connection board(s) installed.
Equipment illustrated for reference only.
Type: 5135CConsole part no.: 405135C-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1645
40
550
0
99-127880
2 pcs. CU51x0 MF/HF Control UnitTT-3043CP Console Panel3 pcs. H1252B Parallel Printer3 pcs. TT-3606E Message Terminal
Weight:excl. units 60 kg.incl. units 89 kg.
Type: 5134CConsole part no.: 405134C-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1245
40
550
0
375
99-126990
CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP-2 Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal
Weight:excl. units 45 kg.incl. units 65 kg.
Type: 5134BConsole part no.: 405134B-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1170
405500
375
99-127178
CU51x0 MF/HF Control UnitTT-3043CP-2 Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal
Weight:excl. units 45 kg.incl. units 65 kg.
Type: 5134FConsole part no.: 405134F-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1445
405500
375
99-129806
CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP-2 Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal1 pcs. TT-3670 IP Handset
Weight:excl. units 50 kg.incl. units 71 kg.
2 Installation Console 5000
2-2 0930
Type: 5134GConsole part no.: 405134G-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1645
405500
375
99-129805
CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP-2 Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal
Weight:excl. units 58 kg.incl. units 78 kg.
Type: 5133CConsole part no.: 405133C-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1245
40
550
0
375
99-126991
CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal
Weight:excl. units 45 kg.incl. units 65 kg.
Type: 5133GConsole part no.: 405133G-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1645
405500
375
99-129807
CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal
Weight:excl. units 58 kg.incl. units 78 kg.
Type: 5133FConsole part no.: 405133F-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1445
405500
375
99-129808
CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel Printer2 pcs. TT-3606E Message Terminal1 pcs. TT-3670 IP Handset
Weight:excl. units 50 kg.incl. units 71 kg.
2 Installation Console 5000
2-3
Type: 5132CConsole part no.: 405132C-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
845
40
550
0
375
99-126992
CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel PrinterTT-3606E Message Terminal
Weight:excl. units 30 kg.incl. units 51 kg.
Type: 5132FConsole part no.: 405132F-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
1045
405500
375
99-129809
CU51x0 MF/HF Control UnitRT502x VHF RadioTT-3043CP Console Panel2 pcs. H1252B Parallel PrinterTT-3606E Message Terminal1 pcs. TT-3670 IP Handset
Weight:excl. units 35 kg.incl. units 57 kg.
Type: 5132BConsole part no.: 405132B-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
770
40
550
0
375
99-127179
CU51x0 MF/HF Control UnitTT-3043CP Console Panel2 pcs. H1252B Parallel PrinterTT-3606E Message Terminal
Weight:excl. units 28 kg.incl. units 45 kg.
Type: 5131AConsole part no.: 405131A-THRxx
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
445
405
375
99-126993
CU51x0 MF/HF Control UnitRT502x VHF Radio
Weight:excl. units 15 kg.incl. units 23 kg.
0930
2 Installation Console 5000
2-4
2.2 Drilling and cutting templateThe console can be placed and mounted, in several different ways, to ensure optimal integration into theuser environment.
2.2.1 Tabletop mounting for 325mm and 400mm section
35846A
Cut for cable entry
for 325mm section.
325
25
375
300
115
85
65
4 mounting holes (ø6)
150
400
4 mounting holes (ø6)
Cut for cable entry
for 400mm section.
25
NB! The table must be sufficiently supported
to carry the console.
****
Drilling template Drilling template
775
727.5
700
400
372.5
327.5
300
75
47.5
0 720
380
320
55
2.2.2 Tabletop mounting for 3 x 400mm section
99-126894
Cut for cable entry
400
25
375
300
115
85
65
150
400
4 mounting holes (ø6)
Cut for cable entry
25
NB! The table must be sufficiently supported
to carry the console.
****
400
4 mounting holes (ø6)
Cut for cable entry
for 400mm section.
Drilling template
4 mounting holes (ø6)
1250
1202.5
1175
875
847.5
802.5
775
475
447.5
402.5
375
75
47.5
0 1195
855
795
455
395
55
0815
2 Installation Console 5000
2-5
2.2.3 Bulkhead mounting for 325mm and 400mm section
Earth stubs entry. Earth stubs entry.
35847B
100 100
0
405
254
300
25
****
**25**
for 325mm section.
Drilling template
for 400mm section.
Drilling template
775
700
637.5
400
387.5
350
312.5
300
75
62.5
0
400325
2.2.4 Bulkhead mounting for 3 x 400mm section
Earth stubs entry. Earth stubs entry.
99-126895
100 100
0
405
300 ****
****
for 400mm section.
Drilling template
Earth stubs entry.
100
**
0
261.3
167.3
73.3
254
130.3
2525
400400400
1250
1203
1175
1033
1017
875
847
775
743.5
545.5
475
375
343.5
145.5
75
0
* To avoid vibration noise, the console should be fastened with screws onto the bulkhead.
** Space from last left- and righthand section to wall.(22.5 + spacing = 25mm)
0815
2 Installation Console 5000
2-6
2.2.5 Earth stubs mounting
Earth stubs entry. Earth stubs entry.
99-127882
100 100
Earth stubs entry.
100
100mm
40mm
15mm
30mm
copper
4 pcs. M6 bolts
Earth stubs made of steel and
welded to the steel bulkhead.
15mm
100mmx0.5mm
0
187.5
587.5
987.5
2.2.6 Placement of print
Earth stubs entry Earth stubs entry
99-129820
100 100
Earth stubs entry
100
Mini-C
Interconnection
Board (1)
Mini-C
Interconnection
Board (2)
Connection
Board (1)
Connection
Board (2)
0930
2 Installation Console 5000
2-7
2.3 Mounting the console onto the bulkheadWhen the console is placed on a table, the back of the console can be attached onto the bulkhead.This allows for free access to the connection board and wiring while installing.
1 Remove the rear (back cover) panels, by removing all 6 screws in each panel.(These will not be needed further and may be discharged of).
2 Remove the edge-profile, from top of the right end of the console (3 screws).3 Remove the plate on the right end of the console (5 screws).
99-126994
2
3
1
4 Remove all key-hole screws from the back.5 Using a hacksaw, cut away the back part, of the bottom plate, by following the pre-cut lines.
Do this on sections, where connection boards are fitted.
99-126995
*
**
**
*
4
5
9
0815
2 Installation Console 5000
2-8
6 Mount all key-hole screws, from the inside of the console.
99-126996
6
**
7 Fasten the console to the bulkhead,with 2 screws per section.
8 Loosen key-hole screws and lift up the front part.
7
Lift here
99-127884
8
12
*
*
*
*
*
*
*
*
*
*
*
*
9 At this point connection board wiring may be donewhile having free access to the connection boards.
10 Fit the front part back onto the key-hole screws.11 Fasten key-hole screws.12 Fasten the console to the table, with four screws per section13 Reinstall the plate, removed in step 3.14 Reinstall the edge-profile, removed in step 2.
0815
2 Installation Console 5000
2-9
2.4 Paper roll
99-126893
min. 680 Clearance required above console
to open top for access to
printer paper roll.
2.5 Control units
99-127913
4 screws M4x4
6 screws M4x6
4 screws M4x8
0815
2 Installation Console 5000
2-10 0815
2.6 Message terminal
37209B
4 screws M4x10
2 Installation Console 5000
2-11
2.7 Factory configuration of the consoleWhen the System 5000 Console is ordered along with the relevant equipment sets and Service Pack partnumber (Service Pack denotes factory installation of units in console) the configuration of the equipmentwill be as per the following notation:
In consoles with two handsets and hence two radio control units, the left side handset is always associatedwith the upper most control unit (MF/HF CU).Supplied with the Console accessory kit are self adhesive labels which may be used to mark therespective handsets for MF/HF and VHF, for ease of identification (Fig. 1).
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
99-128517
MF/HF
VHF
MF/HF 2
Fig.1
Equipment configuration:With two TT-3000EB mini-C installed (Fig. 2) the printer and Message Terminal/keyboard associated with#1 mini-C (part of primary GMDSS equipment) is installed in the left hand side of the console and theassociated mini-C Alarm Panel being the left hand one. The #2 mini-C equipment (part of duplicationGMDSS equipment) is installed in the right hand side, the mini-C Alarm Panel being the right hand one.Both Message Terminals will be configured with the Capsat application software program.The MF/HF controller is installed as the upper most unit (as part of System #1 or primary GMDSSequipment) and the #1 VHF installed below the MF/HF Control Unit also as part of the #1 System orprimary GMDSS equipment.
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
99-128512
#1 mini-C
#1 printer
#1 keyboard
#2 mini-C
#2 printer
#2 keyboard
Fig.2
0815
2 Installation Console 5000
2-12
With one TT-3000EB mini-C and the full MF/HF Radio Telex installed (Fig. 3) the MF/HF Control unit isinstalled as the upper most unit being part of System #1 or primary GMDSS equipment with associatedRadio Telex Message terminal/keyboard and printer installed in the left hand side of the console. Samenotation applies in case of the GMDSS Radio Telex solution without Message Terminal (2-sectionconsole - Fig. 4).The #1 VHF is installed below the MF/HF Control Unit as part of the #1 System or primary GMDSSequipment.The TT-3000EB mini-C is installed in the right hand side of the console being part of System #2 orduplication GMDSS equipment. In the case of two Message Terminals (Fig. 3) these are configured withthe Radio Telex application software program and the Capsat application software program respectively.
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
99-128513
Radiotelex #2 mini-C
mini-C printer
Keyboard
Radiotelex printer
Keyboard
Fig. 3
BATTERY
ALARM
V
1GENCY
EMER-
LIGHT
BATTERY 1
BATTERY 2
2
A
2AC1
ALARM
MUTE/
1 - 2
BATT
DIM
TEST
99-128531
Radiotelex
#2 mini-C
#2 mini-C printer
KeyboardKeyboard
printer
Fig. 4
3 Electrical Installation Console 5000
3-10815
3 Electrical installation
3.1 TT-3606E opt. 003 NMEA Adapter for mini-CIn case the position information generated by the build in GPS receiver of the TT-3026C mini-CTransceiver is required for feeding to other external communication equipment like VHF radios etc., theTT-3606E Opt. 003 NMEA Adapter is required to adapt the information into proper NMEA signal levels.
99-127912
When installing the TT-3606E Opt. 003 NMEA Adapter in the console, the cover of the Adapter box maybe discarded of.
Please refer to the installation manual delivered with the TT-3606E Opt. 003 NMEA Adapter for furtherinstallation information (TT 98-124401). Manual is also available for download from the T&T Extranet/eSupport download area.
3 Electrical Installation Console 5000
3-2 0815
3.2 Grounding cablesGrounding of all external cable screens to the console is important in order to reduce risc of noise andinterference in the GMDSS installation.
The screen of each external cable must be properly terminated to the support bracket by means of a cablelug properly secured to the support bracket with a screw.
99-127906
All internal cable screens are grounded to the support bracket using tie wraps.
99-127907
3 Electrical Installation Console 5000
3-30815
3.3 Console light
Functional descriptionThe intention is to supply the console workplace, with sufficient ambient light for working. If desired, thelight can be turned off completely, so that it does not distract the ship operator, for example during nighttime. However when required the light can be turned on quickly, by means of a switch.
By turning the dimming potentiometer clockwise, the light intensity increases, and correspondinglyturning the potentiometer anti clockwise decreases the light intensity.
The light can be switched on or off, by pushing the to-way switch located just below the dimmingpotentiometer.
If an external two-way light switch is installed for remote control of this console light, this switch shouldbe connected to the appropriate terminals on the primary connection board.
The gooseneck lamp is fed by a regulated DC voltage. The max. voltage supplied to the gooseneck lampis around above 12VDC.
The gooseneck lamp comprise a 3 pin XLR-plug with a release button. Pin 2 carries positive supplyvoltage (+), pin 3 is connected to DC-. Pin 1 is not connected.
The supply for the dimming module is routed from the emergency batteries, through the connection board.
The light source is either by white LED´s or red LED´s. The use of LED´s greatly reduces currentconsumption and heat dissipation normally associated with incandescent lamps.
24V_Light+
24V-
Battery switch
External
circuit
Dimming
Gooseneck
connection
If an external switch is not installed, a jumper wire
GND
24V-
should be placed between "24V_Light+" and "M1".99-126892
M1
M2
3
21
3 Electrical Installation Console 5000
3-4 0815
3.4 Connection boardThe connection board has been designed, so that connectors are grouped in relation to products.
Each connector has been given a unique name and designator in order to clearly identify the connector.Also where the wires are mounted into terminal strips, each connection has been named. The first digitof a designator, is a consecutive number, and the second digit is a digit only used for connectionsbelonging to that group. Every designator starts with an „X“, to indicate that this is a type of connector.For example, the first connector for VHF connection carries the designator „X21“, the second connector„X22“ and so on.
The only connector that differs from the above description, is the connector „Remote“, also designated„X71“. This connector joins the remote function for both „MINI-C“ and „TELEX“.
In consoles with two connection boards, the primary equipment connects to the left connection board. Theduplication equipment connects to the right connection board. This means that for example in commu-nications systems with two VHF radios, the primary VHF is the one located in the console and connectsto the left connection board. The duplication VHF will, if connected through the console connect, to theright hand side connection board.
Component location connection board
X44
X43
3 Electrical Installation Console 5000
3-5
3.5 Schematic connection board
0815
3 Electrical Installation Console 5000
3-6 0815
4 Installation cables Console 5000
4-10815
4 Installation cables
4.1 Console wiring systemThe internal wiring of the console has been grouped and numbered in the following drawings, so that eachcable is easily identified by its unique identifier.
NumberingThe numbering is grouped in three digits, as indicated below. The type of signal carried is also indicatedin the table listing the internal cables.
X.Y.ZZ
C7 = Primary internal 1 = RF/Antenna X.2.00 through 19 = Control/DataC8 = Duplication, backup, internal 2 = Signals X.2.20 through 29 = Relay outputC9 = Common internal 3 = DC power X.2.30 through 39 = Ext. signal
4 = AC power X.3.00 through 09 = Heavy duty DC (distribution)
X.3.10 through 19 = Single power
4 Installation cables Console 5000
4-2 1035
4.2 Internal cables overview
Cable No. Cable type From/To From/To Part No. Signal Conn.
C7.1.00 PL-PL RT50xx RF-Plug 527830 VHF Main RF 1:1C7.1.01 PL-PL RT50xx RF-Plug 527830 VHF DSC RF 1:1
C7.2.00 9-9 pole Sub D CU51x0 MF/HF 56.123 AUX 1:1C7.2.01 9-9 pole Sub D CU51x0 MF/HF 56.123 SCAN-BUS 1:1C7.2.02 Centronics 25 pole Data Terminal/CU Printer Supplied Message 1:1C7.2.03 2 pole mini-C Remote 56.121 On/Off 2C7.2.04 9-9 pole Sub D Data Terminal TT-3616C Supplied Data 1:1C7.2.05 Multi Cable TT-3616C TT-3043CP-2 37-122732-A Data 3C7.2.06 15-15 pole Sub D RT50xx 37-126527 Option 8C7.2.07 15-15 pole Sub D RT50xx 37-126528 SPARC-II 9C7.2.12 8 pole mini din Printer Paper switch 56.122 Control 4C7.2.14 9-9 pole Sub D Data Terminal CU51x0 MF/HF Supplied Data 1:1
C7.3.10 Power Cable Printer Supplied DC supply MC7.3.11 Power Cable Data Terminal Supplied DC supply MC7.3.12 Power Cable TT-3616C 37-123214-B DC supply 5C7.3.13 Power Cable RT50xx Supplied DC supply M
C8.1.00 PL-PL RT50xx RF-Plug 527830 VHF Main RF 1:1C8.1.01 PL-PL RT50xx RF-Plug 527830 VHF DSC RF 1-1
C8.2.00 15-15 pole Sub D RT50xx 37-126527 Option 8C8.2.01 15-15 pole Sub D RT50xx 37-126528 SPARC-II 9C8.2.02 Centronics 25 pole Data Terminal Printer Supplied Message 1:1C8.2.03 9-9 pole Sub D Data Terminal TT-3616C Supplied Data 1:1C8.2.04 Multi Cable TT-3616C TT-3043CP-2 37-122732-A Data 3C8.2.05 2 pole mini-C Remote 56.121 On/Off 2C8.2.06 8 pole mini din Printer Paper switch 56.122 Control 4
C8.3.10 Power Cable RT50xx Supplied DC supply MC8.3.11 Power Cable Printer Supplied DC supply MC8.3.12 Power Cable Data Terminal Supplied DC supply MC8.3.13 Power Cable TT-3616C 37-123214-B DC supply 5
C9.2.01 9-9 pole Sub D Battery Panel 56.123 Batt Sense 1:1C9.2.02 9-9 pole Sub D Battery Panel 56.123 Batt Sense 1:1
C9.3.10 Cable, 2 pole Emg. light/gooseneck 37-126773 DC supply 6C9.3.11 Cable, 4 pole Emg. light-dimmer 37-126772 DC supply 7
Notes:- Where „From/To“ is left blank, the cable is terminated at the connection board 59-126095.
See relevant internal wiring diagrams, for further information.
- „Supplied“ = Designates cable that is supplied with a product, and therefore does not have its ownpart number.
- M = Consult the technical manual for the product.
- Where „Conn.“ is marked with „1:1“, this means that the cable ends are wired pin number 1 to pinnumber 1, pin number 2 to pin number 2, and so on for further pin numbers.Other markings at „Conn.“, refers to cable wiring connection drawings, at the following pages.
2: mini-C Remote, 2 pole:The two wires are soldered on to two terminals, on an on/off push-button switch.
4 Installation cables Console 5000
4-30815
3: Multi cable, TT3043CP-2:TT-3616C TT-3043CP-2+9VDC, White Pin 1GND, Brown Pin 2I/O 0, Red Pin 3I/O 1, Gray Pin 4I/O 2, Yellow Pin 5I/O 3, Green Pin 6I 4, Blue Pin 7I 5, Pink Pin 8
Pin 9, Not connectedPin 10, Not connectedPin 11, Not connectedPin 12, Not connected
Please refer to the installation manual delivered with the TT-3000EB mini-C GMDSS system for furtherinstallation information (TT 98-122414).
4: mini din, paper switch:The two conductors are soldered respectively to pin 1 and pin 2, of the paper switch.Screen is soldered to the bracket for the paper switch.
5: Power cable, TT-3616C:Connection board TT-3616CPin 1, +24V, Red DC +Pin 2, -24V, Black DC -Pin 3, Remote, White Remote On/Off
6: Cable, 2 pole, Emg. light/gooseneck lamp:Connection board Gooseneck lampPin 1 Gooseneck + Pin 2, Light supplyPin 2 - Light Pin 3, Light ref.
7: Cable, 4 pole, Emg. light-dimmer:Dimmer Connection boardPin 1 Pin 2, - LightPin 2 Pin 1, M1Pin 3 Pin 3, M2Pin 4 Pin 4, Gooseneck +
8: Option, 15 pole SUB D connector:Only wire numbers 12, 13 and the screen, is fed through this cable.All other pin numbers has no connection.
9: SPARC-II, 15 pole SUB D connector:Only wire numbers 2, 3, 6, 7 and the screen, is fed through this cable.All other pin numbers has no connection.
4 Installation cables Console 5000
4-4 1035
4.2.1 Internal cables 2 section console w/ MF/HF Radiotelex, mini-C and VHF
99-1
2632
8-A
Prin
ter
On/
Off
Key
boar
d
Bat
tery
Pan
elP
rinte
r
Dat
a T
erm
inal
Inte
rcon
nect
ion
Boa
rdT
T-3
616C
RT
50xx
(rea
r vi
ew)
MF
/HF
CU
51x0
min
i-CT
T-3
043C
P
Key
boar
d
Ligh
tE
mer
genc
y
C7.
2.00
C7.
2.01
C7.
2.12 C7.
1.00
C7.
1.01
C7.2.07C
8.3.
13C
8.3.
12C
8.3.
11C
8.2.
05
C8.
2.03
C8.
2.04
C8.
2.02
C8.
2.06
C9.
2.02
C9.
2.01
C9.
3.11
C9.3.10
C7.3.13
C7.2.06C
7.3.
10
C7.
2.02
Han
dset
AU
XS
CA
N-B
US
Key
boar
dD
ata
Prin
ter
Bat
tery
1B
atte
ry 2
Bat
tery
1B
atte
ry 2
4 Installation cables Console 5000
4-51035
4.2.2 Internal cables 3 section console w/ MF/HF Radiotelex, mini-C and VHF
99-1
2632
9-APrin
ter
Key
boar
d
Prin
ter
Dat
a T
erm
inal
Inte
rcon
nect
ion
Boa
rdT
T-3
616C
MF
/HF
CU
51x0
Key
boar
d
Dat
a T
erm
inal
Bat
tery
Pan
el
RT
50xx
(rea
r vi
ew)
On/
Off
min
i-CT
T-3
043C
P
Ligh
tE
mer
genc
y
On/
Off
C7.
2.00
C7.
2.01
C7.
2.12
C7.
3.11
C7.
3.10
C7.
2.06
C7.
2.07
C7.
1.00
C7.
1.01
C8.
3.13
C8.
3.12
C8.
3.11
C8.
2.05
C8.
2.03
C8.
2.04
C8.
2.02
C8.
2.06
C9.
2.02
C9.
2.01
C9.
3.11
C9.3.10
C7.
2.02
C7.3.13
C7.
2.14
C7.2.03
Han
dset
AU
XS
CA
N-B
US
Key
boar
dD
ata
Prin
ter
Bat
tery
1B
atte
ry 2
Bat
tery
1B
atte
ry 2
4 Installation cables Console 5000
4-6
4.2.3 Internal cables 3 section console w/ MF/HF, 2 x mini-C and VHF
99-1
2633
1-APrin
ter
Key
boar
d
Bat
tery
Pan
elP
rinte
r
Dat
a T
erm
inal
Inte
rcon
nect
ion
Boa
rdT
T-3
616C
RT
50xx
(rea
r vi
ew)
MF
/HF
CU
51x0 K
eybo
ard
Dat
a T
erm
inal
Inte
rcon
nect
ion
Boa
rdT
T-3
616C
On/
Off
On/
Off
min
i-CT
T-3
043C
P-2
Ligh
tE
mer
genc
y
C7.
2.00
C7.
2.01
C7.
2.12
C7.
2.02
C7.
3.12
C7.
3.11
C7.
3.10
C7.
2.03
C7.
2.04
C7.
2.05
C7.
2.06
C7.
1.00
C7.
1.01
C7.
3.13
C8.
3.13
C8.
3.12
C8.
3.11
C8.
2.05
C8.
2.03
C8.
2.04
C8.
2.02
C8.
2.06
C9.
2.02
C9.
2.01
C9.3.10
C9.
3.11
C7.
2.07
Han
dset
AU
XS
CA
N-B
US
Key
boar
dD
ata
Prin
ter
Bat
tery
1B
atte
ry 2
Bat
tery
1B
atte
ry 2
1035
4 Installation cables Console 5000
4-7
4.2.4 Internal cables 1 section console w/ MF/HF and VHF
99-126332-A
Battery Panel
RT50xx(rear view)
MF/HFCU51x0
LightEmergency
C7.2.01
C7.2.00
C7.1.00 C7.1.01
C7.
2.06
C7.
2.07
C7.
3.13
C9.2.01C9.
3.10
C9.3.11Handset AUX SCAN-BUS
Keyboard Data Printer
Battery 1 Battery 2Battery 1 Battery 2
1035
4 Installation cables Console 5000
4-8
4.3 Installation external cabling
4.3.1 External cabling - Emergency light, Battery Panel and position source
99-127898
M1
24V+
External switch
24V-
24V+
Charger
M21
2
3
GND
NMEA -
Position source
NMEA +
-SHUNT
+SHUNT
Power supply/Charger
+VBAT
External shunt box/
1
2
3
AC ALR 1
AC ALR 2
-VBAT4
5
6
24V DC-
24V DC+
AC ALR 07
8
9
1
2
1
2
3
1
2
3
4
5
6
7
8
9
0815
4 Installation cables Console 5000
4-9
4.3.2 External cabling - Alarm Panel
99-127899
GND
SPARC-BUS -
MF/HF - X4
SPARC-BUS + 3
5
2
+24V 9
5065
GND
SPARC-BUS -
VHF - X3
SPARC-BUS + 3
5
2
+24V 9
D-sub
D-sub
D-sub
D-sub
To # 1 mini-C connection board
To # 2 mini-C connection board
1
2
3
4
1
2
3
4
3,7
4,5
8,9
1,2GND
Data +
Data +
VCC IN
3,7
4,5
8,9
1,2GND
Data +
Data +
VCC IN
4.3.3 External cabling - VHF
99-127900
24V DC+
24V DC-
Power Supply
1
2
0815
4 Installation cables Console 5000
4-10
4.3.4 External cabling - MF/HF
99-127901
24V DC +
24V DC -
Power Supply
+24V7
Rx AF+8
Transceiver
SCAN-BUS
AF -5
GND6
Data -3
AF +4
Supply on1
Data +2
Rx AF-9
1
2
7
8
5
6
3
4
1
2
9
D-sub
4.3.5 External cabling - mini-C and Power supply
99-127902
24V DC +
24V DC -
Power Supply
1
2
0815
Thrane & Thrane A/S • [email protected] • www.thrane.com
TT-98-127000-THR-C Issue: C/1035