F-2
Comparative Measuring Instruments
Groove Checking Comparator Gages • GROOVE GAGE .375" – 6" / 10 - 150 mm.• Precise measurement of internal grooves from .375" - 6" / 10 - 150 mm
without ex ten sion.• The finest instrument for reliable checking of ovality, parallelism, grooves,
un der cuts, blind holes and T-slots.• Locking lever and dial locking screw prevent accidental al ter ation of setting.• When the instrument is used with two contact points, it is set by means of a
micrometer; for three-point contact it is set with a ring gage.• Wide or narrow cen ter ing arm holds contact points central when checking
medium and large bores.• Adjustable arm ends.
in mm
79.108640 86149 79.105704 41869 INTERAPID IRA 2
Supplied with the following standard accessories :79.105697* 41866 79.105667* 41862 3 Measuring inserts in hardened steel (No. for 1 item)79.105698* 41867 79.105668* 41863 3 Short measuring inserts in hardened steel (No. for 1 item)79.105699* 41868 79.105669* 41864 3 Long measuring inserts in hardened steel (No. for 1 item)79.112126 41889 79.112126 41889 2 Adjustable contact arms for bores ≥ .03 in / 6 mm79.110113 41884 79.110111 41882 1 Small insert holder for 3-point contact79.110112 41883 79.110110 41881 1 Large insert holder for 3-point contact79.108504 41874 79.108502 41872 1 Centering arm for bores 5/8"-1/4" / 15-30 mm79.108505 41875 79.108503 41873 1 Centering arm for bores 1-1/4"-6" / 30-150 mm79.105694 41865 79.105694 41865 1 Special screwdriver
79.111402 41886 79.111401 41885 INTERAPID IRA 2 mdSame as INTERAPID IRA 2, but furnished with the measuringinserts mentioned below instead of those in steel No. 79.105697 or 79.105667
79.105759* 79.105756* 3 Tungsten carbide tipped measuring inserts (No. for 1 item)* Part number for these items is for one piece. 3 pieces needed per set
�
0.0005 in/ 0.01 mm
0.375 to 6 in /10 to 150 mm
± 0.008 in /to ± 0.20 mm
Armclearance:
40 in / 10 mm
Hardened steel
or tungsten carbidetipped measuring faces:see opposite
3.5 N
Plastic case
Identificationnumber
Declaration of conformity
Technical Data:Capacity: .375 - 6 in / 10 - 150 mmArm clearance: .40 in / 10 mmMeasuring force: 12.5 oz. / 3.5 N (per arm)1 scale division: .0005 in / 0.01 mmScale range: ±.008 in / ± 0.20 mmMax. measuring depth: 2-1/2 in / 62.5 mm
in a 1/2 in dia. / 13 mm dia. hole
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:25 PM Page 2
F-3
Comparative Measuring Instruments
Optional Accessories
79.112051 41887 1 set = 2 Small measuring inserts (1-point contact)1 Small measuring insert (2-point contact)
79.112052 41888 1 set = 2 Large measuring inserts (1-point contact)1 Large measuring insert (2-point contact)
79.108830 41877 Holder
R2 ø3
2.2
R2
2.2
ø3
ø2.
2ø
1
ø3
2.5
3.5
ø1.
4
ø3
5
6
1.4
3
0.8 6
43.
5 2
0.7
2.5
75.
5
1.5
5.5
4
79.105667
79.105756
79.105668
79.105669
79.112126
79.112051 79.112052
�
Steel, hardenedand chrome plated
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:25 PM Page 3
F-4
Comparative Measuring Instruments
Dial Indicator Depth Gages/Round BasesDial Depth Gages for Small HolesRound depth base is 5/8" di am e ter. Contact point is .052" diameter and willmeasure to ap prox i mate ly .650" depth. Dial in di ca tor is graduated in .001"with 1.0" range dial and coun ter -clock wise reading.
599-8941
599-8930 599-8931
599-8940
599-610 44389 Dial Indicator Depth Gage with 599-8931 Depth Base and 14.82028 Dial Indicator
Mounting Collets and Round Depth Bases
Indicator Mounting Collet:599-8940 45053 9/16-18 Mounting Thread; 3/8" hole dia.599-8941 45054 3/8-32 Mounting Thread; 1/4" hole dia.
Round Depth Bases (Individual):599-8930 45051 1" diameter; .240" hole dia. 599-8931 45052 5/8" dia; furnished with .052" dia. contact point
Rectangular Depth Gage Bases Rectangular bases are 9/16" high and have 9/16” tapped holes to ac com mo date In di ca tor Mount ing Collet 599-8940, which is fur nished witheach Rectangular Depth Base on this page.
No. ofMounting Holes Length (in)
599-8922 45046 1 2599-8923 45047 2 3599-8924 45048 3 4599-8926 45049 3 6599-8928 45050 3 8
599-610
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:27 PM Page 4
F-5
Comparative Measuring Instruments
.650".600"
2"599-7252
599-7250 599-7251
Smallest DialMarking Division Dia.
in (in) (in) (in)
599-7250* 27054 .400 0 - 40 .005 1.500599-7251 27055 .400 0 - 100 .001 1.500599-7252 27056 1.00 0 - 100 .001 2.250
* Revolution Counter not available on 599-7250
Dial Thickness GagesA handy addition to any machinist’s tool chest, providing quick measurement ofpaper, film, wire, flat stock, and sheet metal up to 1" thick.
• Lightweight, compact design.• Readings from .001" - .005" with Revolution Counter*.• Black dial face with yellow graduations.
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:32 PM Page 5
F-6
Comparative Measuring Instruments
Dial Snap Gages – Paralloc® "D"Flat Anvils• The most accurate and economical general purpose Dial Snap Gage.• 1 inch anvil adjustment range and 360° Rotational Indicator Mounting for
versa tile operation.• 0 - 18 in / 0 - 458 mm.• Gage pressure may be precisely set to
protect fine finishes and thin-walled parts.• Frame is lightweight, sturdy and well-balanced. Machined from met al lur gi cal ly
stabilized aluminum plate.• “Paralloc” mechanism locks anvil in place by trapping threaded shank.• .66 inch square tungsten carbide anvils are standard. Within the .50 inch cen-
tral square surface, standard square anvils are flat and parallel within .00015inch on sizes up to 4 inches; within .0002 inch on sizes from 4 to 8 inches;within .00025 inch on sizes from 8 to 12 inches; and within .0003 inch on sizesfrom 12 to 18 inches. All anvil edges are chamfered .016 inch by 45°.
Indicator graduations available from .0001 to .001 inch and 0.01 mm to 0.002 mm.Within a .50 inch central square surface, standard square anvils are flat and parallel within .00015 inch on sizes up to 4 inches.
in mmS2-15371 35498 0.00 - 1.00 0 - 25S2-15372 35502 1.00 - 2.00 25 - 51S2-15373 35506 2.00 - 3.00 51 - 76S2-15374 35510 3.00 - 4.00 76 - 102S2-15375 35514 4.00 - 5.00 102 - 127S2-15376 35518 5.00 - 6.00 127 - 152S2-15377 35521 6.00 - 7.00 152 - 178S2-15378 35523 7.00 - 8.00 178 - 203S2-15379 35525 8.00 - 9.00 203 - 229S2-15380 35526 9.00 - 10.00 229 - 254S2-15381 35527 10.00 - 11.00 254 - 279S2-15382 35528 11.00 - 12.00 279 - 305S2-15383 35529 12.00 - 13.00 305 - 330S2-15384 35530 13.00 - 14.00 330 - 356S2-15385 35531 14.00 - 15.00 356 - 381S2-15386 35532 15.00 - 16.00 381 - 406S2-15387 35533 16.00 - 17.00 406 - 432S2-15388 35534 17.00 - 18.00 432 - 458
Standard Indicators for use with Paralloc “D” Snap GagesD1-20241AH 33837 .0001 in 0.25 in 0 - 5 - 0D1-20281AH 33887 .002 mm .5 mm 0 - 10 - 0
Dial Snap Gage – Paralloc® “D” / flat anvil type (sold without Indicator)
in/μmDigital Indicators for use with Paralloc “D” Snap Gages19.30110 26756 0.0005 / 10Adaptor Bracket for Electronic IndicatorsD0-69973 33533
Optional Stand for Paralloc “D” Snap GagesS0-74838 35428
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:33 PM Page 6
F-7
Comparative Measuring Instruments
Indicator rotates 180˚ foreasy viewing in bench-comparator setups.
0 to 18"
inS2-12371 35446 0.00 - 1.00S2-12372 35448 1.00 - 2.00S2-12373 35450 2.00 - 3.00S2-12374 35452 3.00 - 4.00S2-12375 35454 4.00 - 5.00S2-12376 35456 5.00 - 6.00S2-12377 35458 6.00 - 7.00S2-12378 35460 7.00 - 8.00S2-12379 35462 8.00 - 9.00S2-12380 35463 9.00 - 10.00S2-12381 35464 10.00 - 11.00S2-12382 35465 11.00 - 12.00S2-12383 35466 12.00 - 13.00S2-12384 35467 13.00 - 14.00S2-12385 35468 14.00 - 15.00S2-12386 35469 15.00 - 16.00S2-12387 35470 16.00 - 17.00S2-12388 35471 17.00 - 18.00
mmS2-18371 35562 0 - 25S2-18372 35566 25 - 51S2-18373 35570 51 - 76S2-18374 35574 76 - 102S2-18375 35578 102 - 127S2-18376 35582 127 - 152S2-18377 35585 152 - 178S2-18378 35587 178 - 203S2-18379 35589 203 - 229S2-18380 35590 229 - 254S2-18381 35591 254 - 279S2-18382 35592 279 - 305S2-18383 35593 305 - 330S2-18384 35594 330 - 356S2-18385 35595 356 - 381S2-18386 35596 381 - 406S2-18387 35597 406 - 432S2-18388 35598 432 - 458
Standard Indicators for use with Paralloc “D” Snap GagesD1-20241AH 33837 .0001 in 0.25 in 0 - 5 - 0
Standard Indicators for use with Paralloc “D” Snap GagesD1-20281AH 33887 .002 mm .5 mm 0 - 10 - 0
Dial Snap Gage – Paralloc® “D” / flat anvil type (sold with .002 mm Indicator)
Dial Snap Gage – Paralloc® “D” / flat anvil type (sold with .0001” Indicator)
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:33 PM Page 7
F-8
Comparative Measuring Instruments
Dial Snap Gages – Special Applications For purchase information contact Brown & Sharpe at 1-800-283-3600.
Options• Lifting lever available on request. • Bench Stand - Part No. S0-74838.• Cartridge Adapter D0-69973 replaces indicator for use with electronic
indicators or electronic cartridges.
Blade Width Measuring Capacity
.120 in 3 mm .160 in 4 mm .190 in 5 mm in mm
S2-32371 S2-38371 S2-42371 S2-48371 S2-52371 S2-58371 0.00—0.50 0—13S2-32372 S2-38372 S2-42372 S2-48372 S2-52372 S2-58372 0.50— 1.50 13—38S2-32373 S2-38373 S2-42373 S2-48373 S2-52373 S2-58373 1.50—2.50 38—64S2-32374 S2-38374 S2-42374 S2-48374 S2-52374 S2-58374 2.50—3.50 64—89S2-32375 S2-38375 S2-42375 S2-48375 S2-52375 S2-58375 3.50—4.50 89—114S2-32376 S2-38376 S2-42376 S2-48376 S2-52376 S2-58376 4.50—5.50 114—140S2-32377 S2-38377 S2-42377 S2-48377 S2-52377 S2-58377 5.50—6.50 140—165S2-32378 S2-38378 S2-42378 S2-48378 S2-52378 S2-58378 6.50—7.50 165—191S2-32379 S2-38379 S2-42379 S2-48379 S2-52379 S2-58379 7.50—8.50 191—216S2-32380 S2-38380 S2-42380 S2-48380 S2-52380 S2-58380 8.50—9.50 216—241S2-32381 S2-38381 S2-42381 S2-48381 S2-52381 S2-58381 9.50—10.50 241—267S2-32382 S2-38382 S2-42382 S2-48382 S2-52382 S2-58382 10.50—11.50 267—292S2-32383 S2-38383 S2-42383 S2-48383 S2-52383 S2-58383 11.50—12.50 292—318S2-32384 S2-38384 S2-42384 S2-48384 S2-52384 S2-58384 12.50—13.50 318—343S2-32385 S2-38385 S2-42385 S2-48385 S2-52385 S2-58385 13.50—14.50 343—368S2-32386 S2-38386 S2-42386 S2-48386 S2-52386 S2-58386 14.50—15.50 368—394S2-32387 S2-38387 S2-42387 S2-48387 S2-52387 S2-58387 15.50—16.50 394—419S2-32388 S2-38388 S2-42388 S2-48388 S2-52388 S2-58388 16.50—17.50 419—445
Tungsten Carbide blades availableIndicator graduations available from .0001 to .001 inch and 0.01 mm to 0.002 mmIndicators normally furnished are .0001" or 0.002 mm
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:33 PM Page 8
F-9
Comparative Measuring Instruments
TESA CARY Small Horizontal Measuring BenchesTESA CARY BML with fixed anvilSpecially designed for fast and accurate measurement of parts.
TESA CARY BMS with setting spindle on anvil sideSimple non-rotative spindle that can be locked in any position. Very useful formeasuring parts by comparison against a reference setting standard.
�
0 to 82 mm
Insertretraction travel: 26mm
Fixing bore diameter for thesensor: 8h6
Cast-iron base. Othercomponents in hard-ened and
ground steelSensor dependent accuracy
Measuring force is produced bythe sensor
(not included)
2.5 kg
Wooden case
Declaration of con-formityTables and measuringinserts must beordered
together with the measuringbench as accessories. Correctassembly is ensured by themanu facturer for even greater accuracy.
�
0 to 50 mm
Insert retraction: 10 mm
(using the lift lever)Spindle travel: 15 mmFixing bore diameter forthe sensor: 8h6
Cast-iron base.Other components inhardened and
ground steelSensor dependent accuracy
Measuring force is produced by the sensor
(not included)
2.8 kg
Wooden case
Declaration of con-formityTables and measuring insertsmust be ordered
together with the measuringbench as accessories. Correctassembly is ensured by themanu facturer for even greateraccuracy.
Ø 8
26
22
Ø 8
22
Ø 8
22
03330021 29566 TESA CARY small horizontal bench accessories and dial gage not included.
03330018 29563 TESA CARY small horizontal bench BMS, accessories plus electronic probe not included.
03330019 29564 TESA CARY small horizontal bench BMS GT, accessories plus electronic probe not included. This model is provided with a removable table with adjustable height over 8 mm.
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:34 PM Page 9
F-10
Comparative Measuring Instruments
�
0 to 50 mm
Insert retraction travel:10 mm
(using the lever system)Micrometer travel: 15 mmSpindle lock by steps of0.01 mmPlexiglass tube to protectthe micrometer.Fixing bore diameter for the sensor: 8h6
1 mm
Cast-iron base.Other components in hardened
and ground steelSensor dependent accuracy
Measuring force is produced by the sensor
(not included)
3.2 kg
Wooden case
Declaration ofconformityTables and measuring insertsmust be ordered
together with the measuringbench as accessories.Correct assembly is ensured by the manu -facturer for even greateraccuracy.
TESA CARY BMH with micrometer elementThis bench has a mounted micrometer head with a non-rotative, straight-guided spindle. The analog indication features additional graduations with lockby steps of 0.01 mm ensuring quick and reliable positioning of the micrometer.This ingenious device guarantees a positioning accuracy better than 1 µm witha repeatability to < 0.5 µm.
TESA CARY BMCDerived from the BMH model, this small bench has the following keyfeatures:• Analog indication on the TESA CARY MCA8-2 microcomparator
mounted above the measuring point.• Possible assembly of a TESA inductive probe or an electronic indicator.
Ø 8
22
0 5 10 15
60
70
50
03330015 29560 TESA CARY small horizontal bench BMH, accessories and electronic probe not included.
03330016 29561 TESA CARY small horizontal bench BMH IN, accessories and electronic probe not included. (Indication is specially graduated for inside measurement)
03330017 29562 TESA CARY small horizontal bench BMH GT, accessories and electronic probe not included. This model is provided with a removable table withadjustable height over 8 mm using the lever system.
03330020 29565 TESA CARY small horizontal bench BMC with mounted.TESA precision indicator MCA8-2, but without accessories.
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:35 PM Page 10
F-11
Comparative Measuring Instruments
Resting table without support
A B C D
E F G H
Resting tables and support with fine setting,vertically
�
�
Type Description03360336 29602 BT 21 H-shaped table with tungsten carbide resting surface (h = 2 mm) B03360337 29603 BT 41 H-shaped table with tungsten carbide long plate (h = 2 mm) C03360338 29604 BT 51 H-shaped steel table, hardened D03360339 29605 BT 81 H-shaped steel table with borders, hardened F03360340 29606 BT 101 Tilted tungsten carbide table H
Type Description03360327 29593 BT 1 Small table with a 16 mm diameter A03360328 29594 BT 2 H-shaped table with tungsten carbide resting surface (h = 2 mm) B03360329 29595 BT 4 H-shaped table with tungsten carbide long plate (h = 2 mm) C03360330 29596 BT 5 H-shaped steel table, hardened D03360331 29597 BT 6 Small table, 16 mm dia., with tungsten carbide plate (h = 2 mm) E03360332 29598 BT 8 H-shaped steel table with borders, hardened F03360333 29599 BT 9 H-shaped steel table with 3 cups and borders on the front face, hardened G03360334 29600 BT 10 Tilted tungsten carbide table H03360335* 29601 Common table support* Use of the support is required for each measuring bench
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:35 PM Page 11
F-12
Comparative Measuring Instruments
Pairs of measuring inserts for external measurement �
03360301
03360302
03360303
03360304
033603050336030603360307
03360308
03360309
03360310
03360311
03360312
03360313
03360314
03360315
03360316
29567
29568
29569
29570
295712957229573
29574
29575
29576
29577
29578
29579
29580
29581
29582
B111
B112
B121
B122-0.15
B122-0.4B122-0.6B123
B124
B125
B131
B132
B133
B134
B135
B141
B142
Cylindrical, tungsten carbide,1.2 mm in diameter
Cylindrical, tungsten carbide, 2 mm in diameter
Knife-shaped, 0.4 mm wide, 2 mm thick, fitted with diamondpads Flat, tungsten carbide, 3.5 mm wide, 0.15 mm thick
Same as above, 0.4 mm thickSame as above, 0.6 mm thickKnife-shaped, tungsten carbide,3.5 mm wide, 0.05 mm thick,40° angleFlat, tungsten carbide.Thickness: bevel-edged 3.5 mm, standard 0.12 mm(must be indicated on ordering)
Knife-shaped, tungsten carbide,0.05 mm wide, 1.5 mm thick
Cylindrical, tungsten carbide, 2 mm dia. with a 90° V-groove,0.3 mm in depth
Flat, tungsten carbide, 3.5 mmwide, 0.7 mm thick with a 90° V-groove, 0.35 mm in depth
Flat, tungsten carbide, 3.5 mmwide, 0.6 mm thick with a 90°V-groove, 0.4 mm in depth
Flat, tungsten carbide, 3.5 mmwide, 0.85 mm thick; with two90° V-grooves, 0.4 mm or 0.8 mm in depth
Flat, tungsten carbide, 5 mmwide, 0.6 mm thick, with one ortwo 90° V-grooves, 0.4 mm indepth. Hardened steel V-racks,0.12 mm thick
With two 90° V-grooves, tung-sten carbide, 0.5 or 0.8 mm indepth. Possible setting for vary-ing diameters up to 1 mm
With one or two 90° V-grooves,tungsten carbide, 0.6 mm indepth. Hardened steel V-racks,0.12 mm thick, adjustable forvarying diameters up to 1 mm
Measure diameters on cylin -drical parts, e.g. staffs, arbors,rods, pins, balls, spheresSame as B111 plus thicknessof prismatic parts, bars, wash-ers, bladesMeasure diameters on watchstones. Tracked counter-pivots.Mounted on a wireMeasure diameters and thick-ness on watch stones, washersetc.Same as aboveSame as aboveMeasure diameters of slots,grooves, short staffs, pinioncoresMeasure diameters on staff piv-ots of watch wheels and pin-ions
Measure diameters on gages,gauge rods and staffs
Measure diameters on cylindricalparts, e.g. staffs, arbors, rods,pins, balls, spheres or distancebetween shouldersMeasure diameters and thick-ness on watch stones, wash-ers, files or distance be tween shouldersMeasure distance betweenshoulders and diameters ofstaff, rods, bearing pins, pin-ionsMeasure distance betweenshoulders of staffs, bearingpins, rods, pinions for pivot diameters up to 1.5 mm
Measure distance betweenshoulders or centers of staffs,rods or pinions
Measure distance betweenshoulders or centers of staffs,rods or pinions
Measure distance betweenshoulders or centers of staffs,rods or pinions with varyingpivot diameters
A-C-D-F-G
A-C-D-F-G
C-H
A-C-D-F-G
As aboveAs aboveA-D-F-G
B
E
A-C-D-F-G
A-C-D-F-G
A-C-D-F-G
A-C-D-F-G
A-D-F-G
A-D-F-G
–
Characteristics Applications Appropriate(as examples) Tables
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:35 PM Page 12
F-13
Comparative Measuring Instruments
Pairs of measuring inserts for external measurement
B 111 B 112 B 121 B 122 / 0.15 – 0.4 – 0.6
B 123 B 124 B 125 B 131
B 132 B 133 B 134
B 141 B 151 B 152
B 135
�
Characteristics Applications Appropriate(as examples) Tables
03360317
03360318
0336031903360320
29583
29584
2958529586
B151
B152
BTS121-47B151-9
Jaws, tungsten carbide, 3.5 mm wide, in excess by 1.5 mm on top, full angle to 79°
Jaws, tungsten carbide,1.5 mm thick, in excess by 1.3 mm sideways, full angle to 80°
Width of the leaves of pinions,lowest module 0.05 mm
Width of wheel, lowest module0.05 mm
A-D-F-G
E
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:35 PM Page 13
F-14
Comparative Measuring Instruments
Pairs of measuring inserts for internal measurement, without holder
<Ø 0.60.8 <Ø 11
B 171 B 172
<Ø 1.5
1.4 <Ø 2.5
1.8
B 173 B 174
<1.45
0.9
Ø 1
B 175 B 200
�
Characteristics03360321 29587 B171 For internal dimensions from 0.6 to 4 mm03360322 29588 B172 For internal dimensions from 1 to 5 mm03360323 29589 B173 For internal dimensions from 1.5 to 6 mm03360324 29590 B174 For internal dimensions from 2.5 to 7 mm03360325 29591 B175 For inside grooves from 1.45 mm03360326* 29592 B200 Probe holder for inside measurement:
measuring capacity from 0.6 to 7 mm* Use of the support is required for each measuring bench.
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:35 PM Page 14
F-15
Comparative Measuring Instruments
�
Steel inserts,hardened
Finished lappedmeasuring faces
QUICK CONTROLalone: 2μm
0 to N, adjustable.Can be reversed from “neutral” to inter-
nal or external measuring
Plastic case
Identification number
Declaration ofconformity
TESA QUICK-CONTROLfor Stationary UseVersatile instrument for comparative measurement of internal or external dimensions -Ideal for part series inspection - Accommodates a clamping fixture for mounting amechanical dial gage, an electronic indicator or an axial probe having a 8 mm diameterfixing shank.
• Solidly built, easily mounted, simple to use.• Wide application range from the smallest internal dimension of 2 mm up to
the highest dimension of 425 mm.• Measures workpieces with plan parallel surfaces as well as cylindrical or
conical surfaces, e.g. shafts, through holes, blind bores, short centeringshoulders, grooves and wall thickness - Checks gear diameters -
• Determines form and position errors such as roundness, concentricity, coaxialityerrors and the like.
03360032
03360042
03360025
03360027
in mm in mm
Internal measurement External measurement03330000 29460 QUICK-CONTROL 1 0.33 x 7.68 8.5 x 195 0 x 6.70 0 x 17003330001 29461 QUICK-CONTROL 2 1.85 x 16.93 47 x 430 0 x 16.73 0 x 425
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:36 PM Page 15
F-16
Comparative Measuring Instruments
03360057/58
03360033 03360034
03360059/60
5
Ø 9
14.5
M2.
5
M2.
5
20
03360032
33
20
60
03360031
Ø 5 48
0.5 4
12
3
03360029
Ø 8 52
11˚
Ø 10
R=0.3
03360027
12
Ø 8 524
2
03360025
Ø 5
17
Ø 8
55
03360022/23
38 / 110
Ø 8
Ø 12 85 /
145
Ø 23R=0.3
03360061/62
60 / 200
Ø 12Ø 12
70 /
130
Ø 30
R=
1
60˚
5.6
03360063
Ø 8
Ø 12
55
03360064
Ø 14.5
32
Standard Accessories
QUICK-CONTROL 103360022 29462 1 Insert holder for external or internal dimensions up to 115 mm or from 2 to 143 mm, resp.03360023 29463 1 Insert holder for external or internal dimensions from 97 to 170 mm or 115 to 208 mm, resp.03360025 29464 1 Pair of insert adapters, shaft diameter 8 mm for 5 mm03360027 29465 Measuring insert for checking bores, external diameters and grooves03360029 29466 Measuring insert for checking internal or external diameters, through and blind bores03360031 29467 1 Pair of inserts for external dimensions from 8.5 mm03360032 29468 1 Pair of raising supports for insert adapters No. 0336002503360033 29469 1 Extension, 20 mm long, for dial gage plunger03360034 29470 1 Blocking segment for insert holder
QUICK-CONTROL 203360057 29471 1 Pair of measuring inserts for external dimensions from 47 mm03360058 29472 1 Pair of measuring inserts for internal dimensions from 47 mm03360059 29473 1 Pair of disc-shaped measuring inserts for external dimensions from 62 mm03360060 29474 1 Pair of disc-shaped measuring inserts for internal dimensions from 62 mm03360061 29475 1 Insert holder, 60 mm long, with a 12 mm clamping bore03360062 29476 1 Insert holder, 200 mm long, with a 12 mm clamping bore03360063 29477 1 Pair of adapters for measuring inserts, shaft diameter 12 for 8 mm03360064 29478 1 Blocking segment for insert holder
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:36 PM Page 16
F-17
Comparative Measuring Instruments
M2.
5
M2.
560
Ø 8
03360045
Min. 10Max. 20
Ø 8
03360050
Min. 18Max. 70
Ø 8
03360051
Ø 5
17
Ø 8
3603360024
12
Ø 8 25
4
2
03360026
Ø 8 25
11˚
Ø 10
R=0.3
03360028
Ø 5 25
0.5 4
12
3
03360030
15
Ø 8
25 /
52
2
03360035/36
16
Ø 8
25 /
52
2
03360037/38
18
Ø 8
25 /
52
2
03360039/40
Ø 5
25 /
48
1
4
10
1.5
03360041/42
Ø 8 25 /
52
60˚
03360043/44
Optional Accessories (must be ordered separately)
Sec.F_CompMeas.REVISED:Sec.F_CompMeas.REVISED 8/7/06 3:36 PM Page 17