m³/h
mbar abs.
10
mbar abs.
2
kW
20 40 60 100 1000
100
120
140
3
4
6
5
160
200 400 600
180
200
220
10 20 40 60 100 1000200 400 600
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Inlet pressure p1
Inlet pressure p1
© Gardner Denver Deutschland GmbH 1 Techn. data sheet 2BV5 110, edition 12/2004 En
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 110 Vacuum pump
Performance curves for vacuum operation
Vacuum pumps of the L-BV5 range are suitable for evacuating gases and wet vapours down to inlet pressures of 33 mbar abs.(97% vacuum). All these vacuum pumps are equipped with built-in cavitation protection. For operation below 80 mbar abs. the cavita-tion protection should be connected to protect the vacuum pump.All pumps L-BV5 are especially space-saving in their monoblock design. They are available in cast iron (standard color RAL 9006). The motor is painted as standard in RAL 9006.
The motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA. Vacuum pumps with ATEX 94/9 EG for category 2G are available, too.The characteristics are valid for the inlet of air with a relative humidity of 100 % and a temperature of 20 °C, compression to 1013 mbar abs. and water at 15 °C as operating liquid. The tolerance is ± 10 %.
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
The motors are designed according to DIN EN 60 034 / DIN IEC 34-1 andtemperature class F. For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range.For all three phase machines according to UL and CSA norm (UL 507 and CSA 22.2 No. 100) the maximum allowed voltage tolerances are -10 % resp. +6 %. The frequency tolerance is maximum ± 2 %.
All L-BV5 achieve the standards and norms of the low voltage directive 72/23/E�G,L-BV5 achieve the standards and norms of the low voltage directive 72/23/E�G,BV5 achieve the standards and norms of the low voltage directive 72/23/E�G,rotating electrotechnical motor EN 60034-1-34, electromagnetic compatibility (EMC)DIN EN 61000-0/-6/-4.
* For standard UL 507 and CSA 22.2 No 113 (Certificate Number E225239).** Measuring-surface sound-pressure level acc. to DIN EN 21680, measured at a distance of 1 m at medium inlet pressure and with connected pipes.*** The quantities of operating liquid apply for fresh water operation without discharge liquid separator.For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid,available as accessories).
An inlet pressure of 10 mbar abs. can be achieved by connecting a gas ejector (seeaccessories). The gas ejector can be mounted directly onto the vacuum pump.
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain/FlushingN8.7 Cavitation protection
Other voltages2BV5 110-..5 110-..-..¨ ..-¨S
50 Hz 60 Hz
3~
185…220 V �� / 320…380 V ��� / 320…380 V � / 320…380 V �220…240 V �� / 345…415 V ��� / 345…415 V � / 345…415 V �345…415 V ����500 V ����
200…254 V �� / 345…440 V ��� / 345…440 V � / 345…440 V �220…275 V �� / 380…480 V ��� / 380…480 V � / 380…480 V �380…480 V ����575 V ����
HHHH
0875
3~ ATEX Category 2G
230 V �� / 400 V ��� / 400 V � / 400 V �400 V �� / 690 V ��� / 690 V � / 690 V �500 V ����
---
DDD
165
---
460 V ����460 V �575 V ��
GGG
615
2BV5 110 a b b1 b2 c1 c2 h1 h2 h3 h4 h5 h6 h7 h8 k l f g n s1
[mm] 639 326 255 190 20 26 140 153 203 361 288 38 58 231 295 129 468 208 91 12 x 23
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
12 340 M32x1.5 19 160 123 97 52 42 180 52 25 DN50 / 2“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc. to DIN 2501, ND16 or ANSI B16.5-3-1502) suitable for round flange acc. to DIN 2633, ND16, nominal width 15 or ANSI B16.5-1/2-150
Selection and ordering dataMaterials
Casing/port plate/impeller
Motor data Ser-vice-factor
Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
�eightapprox.
Fre-quency
Rated
voltage current output
Hz V A kW SF m³/h dB(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron/cast iron/bronze50 60
200��...240��220��...275��
345�...415�380�...480�
19.020.0
11.011.5
4.06.2
1.31.0
2BV5110-0KH01-8S0.80.8
6367
86
cast iron/cast iron/bronze50 60
345��...415��380��...480��
11.011.5
4.06.2
1.31.0
2BV5110-0KH01-7S0.80.8
6367
86
cast iron/cast iron/bronze50 60
500����575����
9.09.2
4.06.2
1.31.0
2BV5110-0KH01-5S0.80.8
6367
86
CrNi steel/CrNi steel/CrNi steel50 60
200��...240��220��...275��
345�...415�380�...480�
19.020.0
11.011.5
4.06.2
1.31.0
2BV5110-0HH01-8S0.80.8
6367
86
CrNi steel/CrNi steel/CrNi steel50 60
345��...415��380��...480��
11.011.5
4.06.2
1.31.0
2BV5110-0HH01-7S0.80.8
6367
86
CrNi steel/CrNi steel/CrNi steel50 60
500����575����
9.09.2
4.06.2
1.31.0
2BV5110-0HH01-5S0.80.8
6367
86
Quantity of Operating LiquidFrequency for fresh water operation / partial recirculation Inlet pressure p (abs.) ***
< 200 mbar 200 - 500 mbar > 500 mbar
Hz m³/h m³/h m³/h
50 0.8 / 0.45 0.35 / 0.25 0.3 / 0.12
60 0.8 / 0.45 0.35 / 0.25 0.3 / 0.12
Max. add. water carry-over or permissible back pressure
Frequencymax. additionaladditionalwater carry-over
max. permissiblepermissibleback pressure
Hz m³/h mbar abs.
50 2.0 1300
60 2.5 1300
© Gardner Denver Deutschland GmbH 2 Techn. data sheet 2BV5 110, edition 12/2004 En
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron/Grey cast iron/Bronze CrNi steel/CrNi steel/CrNi steel
002 CasingGrey cast iron(EN-GJL HB 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
005 Pump shaftChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
035 Mechanical sealSIC / Carbon / Viton (FPM) /Chrome-nickel-molybdenum steel (EN 12756 - BQ1VGG)
SIC / Carbon / Viton (FPM) / Teflon (PTFE) sheated /Chrome-nickel-molybdenum steel (EN 12756 - Q1BM1GG)
036 �asherChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 / CC33G-GS) EN 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
048Tolerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
049 Port plateGrey cast iron(EN-GJL HB 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
050 Valve plate Teflon (PTFE) Teflon (PTFE)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (NBR 70) ISO 1629 Silicone core, Teflon (PTFE) sheated
061 CoverGrey cast iron(EN-GJL HB 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
069 Sealing ring Teflon (PTFE) Teflon (PTFE)
071Pipe of cavitation protection
Teflon (PTFE) Teflon (PTFE)
072�asher for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
079 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
080 Sealing ring Teflon (PTFE) Teflon (PTFE)
© Gardner Denver Deutschland GmbH 3 Techn. data sheet 2BV5 110, edition 12/2004 En
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 Bad Neustadt - Germany
Tel.: +49 7622 392-0Fax: +49 7622 392-300
Tel.: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve, datas and weights without prior notice. The figures are without obligations.
m³/h
mbar abs.
10
mbar abs.
2
kW
20 40 60 100 1000
100
150
3
4
6
5
200
200 400 600
250
300
10 20 40 60 100 1000200 400 600
7
8
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Inlet pressure p1
Inlet pressure p1
© Gardner Denver Deutschland GmbH 1 �echn�� data sheet 2�V5 111�� edition 12�2004 �n�echn�� data sheet 2�V5 111�� edition 12�2004 �n
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 111 Vacuum pump
Performance curves for vacuum operation
Vacuum pumps of the L-�V5 range are suitable for evacuating gases and wet vapours down to inlet pressures of 33 mbar abs��(97% vacuum)�� All these vacuum pumps are equipped with built-in cavitation protection�� For operation below 80 mbar abs�� the cavita-tion protection should be connected to protect the vacuum pump��All pumps L-�V5 are especially space-saving in their monoblock design�� �hey are available in cast iron (standard color RAL 9006)�� �he motor is painted as standard in RAL 9006��
�he motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA�� Vacuum pumps with A��X 94�9 �G for category 2G are available�� too���he characteristics are valid for the inlet of air with a relative humidity of 100 % and a temperature of 20 °C�� compression to 1013 mbar abs�� and water at 15 °C as operating liquid�� �he tolerance is ± 10 %��
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
�he motors are designed according to DIN �N 60 034 � DIN I�C 34-1 andtemperature class F�� For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range��For all three phase machines according to UL and CSA norm (UL 507 and CSA 22��2 No�� 100) the maximum allowed voltage tolerances are -10 % resp�� +6 %�� �he frequency tolerance is maximum ± 2 %��
All L-�V5 achieve the standards and norms of the low voltage directive 72�23��WG��rotating electrotechnical motor �N 60034-1-34�� electromagnetic compatibility (�MC)DIN �N 61000-0�-6�-4��
* For standard UL 507 and CSA 22��2 No 113 (Certificate Number �225239)��** Measuring-surface sound-pressure level acc�� to DIN �N 21680�� measured at a distance of 1 m at medium inlet pressure and with connected pipes��*** �he quantities of operating liquid apply for fresh water operation without discharge liquid separator��For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid��available as accessories)��
An inlet pressure of 10 mbar abs�� can be achieved by connecting a gas ejector (seeaccessories)�� �he gas ejector can be mounted directly onto the vacuum pump��
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain�FlushingN8.7 Cavitation protection
Other voltages2�V5 111-����5 111-����-����¨ ����-¨S
50 Hz 60 Hz
3~
185…220 V �� � 320…380 V ��� � 320…380 V � � 320…380 V �220…240 V �� � 345…415 V ��� � 345…415 V � � 345…415 V �345…415 V ����500 V ����
200…254 V �� � 345…440 V ��� � 345…440 V � � 345…440 V �220…275 V �� � 380…480 V ��� � 380…480 V � � 380…480 V �380…480 V ����575 V ����
HHHH
0875
3~ ATEX Category 2G
230 V �� � 400 V ��� � 400 V � � 400 V �400 V �� � 690 V ��� � 690 V � � 690 V �500 V ����
---
DDD
165
2�V5 111 a b b1 b2 c1 c2 h1 h2 h3 h4 h5 h6 h7 h8 k l f g n s1
[mm] 653 326 265 190 20 26 151 166 213 371 318 48 68 258 291 128 482 224 91 12 x 23
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
12 340 M32x1��5 19 160 123 97 52 42 180 52 27 DN50 � 2“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc�� to DIN 2501�� ND16 or ANSI �16��5-3-1502) suitable for round flange acc�� to DIN 2633�� ND16�� nominal width 15 or ANSI �16��5-1�2-150
Selection and ordering dataMaterials
Casing�port plate�impeller
Motor data Ser-vice-factor
Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
Weightapprox��
Fre-quency
Rated
voltage current output
Hz V A kW SF m³�h d�(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron�cast iron�bronze50 60
200��������240��220��������275��
345�������415�380�������480�
27��527��5
16��016��0
5.58.2
1��271��0
2BV5111-0KH03-8S1��21��0
6874
105
cast iron�cast iron�bronze50 60
345��������415��380��������480��
16��016��0
5.58.2
1��271��0
2BV5111-0KH03-7S1��21��0
6874
105
cast iron�cast iron�bronze50 60
500����575����
12��512��8
5.58.2
1��271��0
2BV5111-0KH03-5S1��21��0
6874
105
CrNi steel�CrNi steel�CrNi steel50 60
200��������240��220��������275��
345�������415�380�������480�
27��527��5
16��016��0
5.58.2
1��271��0
2BV5111-0HH03-8S1��21��0
6874
105
CrNi steel�CrNi steel�CrNi steel50 60
345��������415��380��������480��
16��016��0
5.58.2
1��271��0
2BV5111-0HH03-7S1��21��0
6874
105
CrNi steel�CrNi steel�CrNi steel50 60
500����575����
12��512��8
5.58.2
1��271��0
2BV5111-0HH03-5S1��21��0
6874
105
Quantity of Operating LiquidFrequency for fresh water operation � partial recirculation Inlet pressure p (abs��) ***
< 200 mbar 200 - 500 mbar > 500 mbar
Hz m³�h m³�h m³�h
50 1��2 � 0��5 0��4 � 0��3 0��35 � 0��12
60 1��0 � 0��5 0��4 � 0��3 0��35 � 0��12
Max. add. water carry-over or permissible back pressure
Frequencymax�� additionaladditionalwater carry-over
max�� permissiblepermissibleback pressure
Hz m³�h mbar abs��
50 3��0 1300
60 3��0 1300
© Gardner Denver Deutschland GmbH 2 �echn�� data sheet 2�V5 111�� edition 12�2004 �n�echn�� data sheet 2�V5 111�� edition 12�2004 �n
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron�Grey cast iron��ronze CrNi steel�CrNi steel�CrNi steel
002 CasingGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
005 Pump shaftChrome steel(X20Cr13 � 1��4021) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
035 Mechanical sealSIC � Carbon � Viton (FPM) �Chrome-nickel-molybdenum steel (�N 12756 - �Q1VGG)
SIC � Carbon � Viton (FPM) � �eflon (P�F�) sheated �Chrome-nickel-molybdenum steel (�N 12756 - Q1�M1GG)
036 WasherChrome steel(X20Cr13 � 1��4021) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 � CC33G-GS) �N 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
048�olerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 � 1��4310) �N 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 � 1��4310) �N 10088 - 2
049 Port plateGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
050 Valve plate �eflon (P�F�) �eflon (P�F�)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMo�i 18-10 � 1��4571) �N 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMo�i 18-10 � 1��4571) �N 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (N�R 70) ISO 1629 Silicone core�� �eflon (P�F�) sheated
061 CoverGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel�� lead alloyed(11SMnPb30 � 1��0718) �N 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 3
069 Sealing ring �eflon (P�F�) �eflon (P�F�)
071Pipe of cavitation protection
�eflon (P�F�) �eflon (P�F�)
072Washer for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 � 1��4301) �N 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 � 1��4301) �N 10088 - 3
079 Plug screwMachining steel�� lead alloyed(11SMnPb30 � 1��0718) �N 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 3
080 Sealing ring �eflon (P�F�) �eflon (P�F�)
© Gardner Denver Deutschland GmbH 3 �echn�� data sheet 2�V5 111�� edition 12�2004 �n�echn�� data sheet 2�V5 111�� edition 12�2004 �n
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 �ad Neustadt - Germany
info@de��gardnerdenver��comwww��gd-elmorietschle��com
�el��: +49 7622 392-0Fax: +49 7622 392-300
�el��: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve�� datas and weights without prior notice�� �he figures are without obligations��
m³/h
mbar abs.
10
mbar abs.
4
kW
20 40 60 100 1000
150
350
5
6
8
7
200
200 400 600
250
300
10 20 40 60 100 1000200 400 600
9
10
400
11
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Inlet pressure p1
Inlet pressure p1
© Gardner Denver Deutschland GmbH 1 �echn�� data sheet 2�V5 121�� edition 12�2004 �n�echn�� data sheet 2�V5 121�� edition 12�2004 �n
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 121 Vacuum pump
Performance curves for vacuum operation
Vacuum pumps of the L-�V5 range are suitable for evacuating gases and wet vapours down to inlet pressures of 33 mbar abs��(97% vacuum)�� All these vacuum pumps are equipped with built-in cavitation protection�� For operation below 80 mbar abs�� the cavita-tion protection should be connected to protect the vacuum pump��All pumps L-�V5 are especially space-saving in their monoblock design�� �hey are available in cast iron (standard color RAL 9006)�� �he motor is painted as standard in RAL 9006��
�he motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA�� Vacuum pumps with A��X 94�9 �G for category 2G are available�� too���he characteristics are valid for the inlet of air with a relative humidity of 100 % and a temperature of 20 °C�� compression to 1013 mbar abs�� and water at 15 °C as operating liquid�� �he tolerance is ± 10 %��
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
�he motors are designed according to DIN �N 60 034 � DIN I�C 34-1 andtemperature class F�� For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range��For all three phase machines according to UL and CSA norm (UL 507 and CSA 22��2 No�� 100) the maximum allowed voltage tolerances are -10 % resp�� +6 %�� �he frequency tolerance is maximum ± 2 %��
All L-�V5 achieve the standards and norms of the low voltage directive 72�23���G��L-�V5 achieve the standards and norms of the low voltage directive 72�23���G���V5 achieve the standards and norms of the low voltage directive 72�23���G��rotating electrotechnical motor �N 60034-1-34�� electromagnetic compatibility (�MC)DIN �N 61000-0�-6�-4��
* For standard UL 507 and CSA 22��2 No 113 (Certificate Number �225239)��** Measuring-surface sound-pressure level acc�� to DIN �N 21680�� measured at a distance of 1 m at medium inlet pressure and with connected pipes��*** �he quantities of operating liquid apply for fresh water operation without discharge liquid separator��For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid��available as accessories)��
An inlet pressure of 10 mbar abs�� can be achieved by connecting a gas ejector (seeaccessories)�� �he gas ejector can be mounted directly onto the vacuum pump��
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain�FlushingN8.7 Cavitation protection
Other voltages2�V5 121-����5 121-����-����¨ ����-¨S
50 Hz 60 Hz
3~
185…220 V �� � 320…380 V ��� � 320…380 V � � 320…380 V �220…240 V �� � 345…415 V ��� � 345…415 V � � 345…415 V �345…415 V ����500 V ����
200…254 V �� � 345…440 V ��� � 345…440 V � � 345…440 V �220…275 V �� � 380…480 V ��� � 380…480 V � � 380…480 V �380…480 V ����575 V ����
HHHH
0875
3~ ATEX Category 2G
230 V �� � 400 V ��� � 400 V � � 400 V �400 V �� � 690 V ��� � 690 V � � 690 V �500 V ����
---
DDD
165
---
460 V ����460 V �575 V ����
GGG
615
2�V5 121 a b b1 b2 c1 c2 h1 h2 h3 h4 h5 h6 h7 h8 k l f g n s1
[mm] 752 348 265 190 20 26 151 167 217 385 318 39 60 258 336 135 565 262 96 12 x 23
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
12 382 M32x1��5 19 182 142 114 67 42 200 57 29 DN65 � 2½“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc�� to DIN 2501�� ND16 or ANSI �16��5-3-1502) suitable for round flange acc�� to DIN 2633�� ND16�� nominal width 15 or ANSI �16��5-1�2-150
Selection and ordering dataMaterials
Casing�port plate�impeller
Motor data Ser-vice-factor
Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
�eightapprox��
Fre-quency
Rated
voltage current output
Hz V A kW SF m³�h d�(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron�cast iron�bronze50 60
200��������240��220��������275��
345�������415�380�������480�
38��039��0
22��022��5
7.511.4
1��31��0
2BV5121-0KH03-8S1��21��5
6975
165
cast iron�cast iron�bronze50 60
345��������415��380��������480��
21��021��5
7.511.4
1��31��0
2BV5121-0KH03-7S1��21��5
6975
165
cast iron�cast iron�bronze50 60
500����575����
16��016��5
7.511.4
1��31��0
2BV5121-0KH03-5S1��21��5
6975
165
CrNi steel�CrNi steel�CrNi steel50 60
200��������240��220��������275��
345�������415�380�������480�
38��039��0
22��022��5
7.511.4
1��31��0
2BV5121-0HH03-8S1��21��5
6975
165
CrNi steel�CrNi steel�CrNi steel50 60
345��������415��380��������480��
21��021��5
7.511.4
1��31��0
2BV5121-0HH03-7S1��21��5
6975
165
CrNi steel�CrNi steel�CrNi steel50 60
500����575����
16��016��5
7.511.4
1��31��0
2BV5121-0HH03-5S1��21��5
6975
165
Quantity of Operating LiquidFrequency for fresh water operation � partial recirculation Inlet pressure p (abs��) ***
< 200 mbar 200 - 500 mbar > 500 mbar
Hz m³�h m³�h m³�h
50 1��2 � 0��6 0��4 � 0��3 0��35 � 0��12
60 1��5 � 0��6 0��4 � 0��3 0��35 � 0��12
Max. add. water carry-over or permissible back pressure
Frequencymax�� additionaladditionalwater carry-over
max�� permissiblepermissibleback pressure
Hz m³�h mbar abs��
50 3��0 1300
60 3��5 1300
© Gardner Denver Deutschland GmbH 2 �echn�� data sheet 2�V5 121�� edition 12�2004 �n�echn�� data sheet 2�V5 121�� edition 12�2004 �n
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron�Grey cast iron��ronze CrNi steel�CrNi steel�CrNi steel
002 CasingGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
005 Pump shaftChrome steel(X20Cr13 � 1��4021) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
035 Mechanical sealSIC � Carbon � Viton (FPM) �Chrome-nickel-molybdenum steel (�N 12756 - �Q1VGG)
SIC � Carbon � Viton (FPM) � �eflon (P�F�) sheated �Chrome-nickel-molybdenum steel (�N 12756 - Q1�M1GG)
036 �asherChrome steel(X20Cr13 � 1��4021) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 � CC33G-GS) �N 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
048�olerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 � 1��4310) �N 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 � 1��4310) �N 10088 - 2
049 Port plateGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
050 Valve plate �eflon (P�F�) �eflon (P�F�)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMo�i 18-10 � 1��4571) �N 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMo�i 18-10 � 1��4571) �N 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (N�R 70) ISO 1629 Silicone core�� �eflon (P�F�) sheated
061 CoverGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel�� lead alloyed(11SMnPb30 � 1��0718) �N 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 3
069 Sealing ring �eflon (P�F�) �eflon (P�F�)
071Pipe of cavitation protection
�eflon (P�F�) �eflon (P�F�)
072�asher for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 � 1��4301) �N 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 � 1��4301) �N 10088 - 3
079 Plug screwMachining steel�� lead alloyed(11SMnPb30 � 1��0718) �N 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 3
080 Sealing ring �eflon (P�F�) �eflon (P�F�)
© Gardner Denver Deutschland GmbH 3 �echn�� data sheet 2�V5 121�� edition 12�2004 �n�echn�� data sheet 2�V5 121�� edition 12�2004 �n
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 �ad Neustadt - Germany
info@de��gardnerdenver��comwww��gd-elmorietschle��com
�el��: +49 7622 392-0Fax: +49 7622 392-300
�el��: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve�� datas and weights without prior notice�� �he figures are without obligations��
m³/h
mbar abs.
10
mbar abs.
6
kW
20 40 60 100 1000
250
450
8
300
200 400 600
350
400
10 20 40 60 100 1000200 400 600
14
500
16
10
12
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Inlet pressure p1
Inlet pressure p1
© Gardner Denver Deutschland GmbH 1 �echn�� data sheet 2�V5 131�� edition 12�2004 �n�echn�� data sheet 2�V5 131�� edition 12�2004 �n
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 131 Vacuum pump
Performance curves for vacuum operation
Vacuum pumps of the L-�V5 range are suitable for evacuating gases and wet vapours down to inlet pressures of 33 mbar abs��(97% vacuum)�� All these vacuum pumps are equipped with built-in cavitation protection�� For operation below 80 mbar abs�� the cavita-tion protection should be connected to protect the vacuum pump��All pumps L-�V5 are especially space-saving in their monoblock design�� �hey are available in cast iron (standard color RAL 9006)�� �he motor is painted as standard in RAL 9006��
�he motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA�� Vacuum pumps with A��X 94�9 �G for category 2G are available�� too���he characteristics are valid for the inlet of air with a relative humidity of 100 % and a temperature of 20 °C�� compression to 1013 mbar abs�� and water at 15 °C as operating liquid�� �he tolerance is ± 10 %��
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
�he motors are designed according to DIN �N 60 034 � DIN I�C 34-1 andtemperature class F�� For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range��For all three phase machines according to UL and CSA norm (UL 507 and CSA 22��2 No�� 100) the maximum allowed voltage tolerances are -10 % resp�� +6 %�� �he frequency tolerance is maximum ± 2 %��
All L-�V5 achieve the standards and norms of the low voltage directive 72�23���G��L-�V5 achieve the standards and norms of the low voltage directive 72�23���G���V5 achieve the standards and norms of the low voltage directive 72�23���G��rotating electrotechnical motor �N 60034-1-34�� electromagnetic compatibility (�MC)DIN �N 61000-0�-6�-4��
* For standard UL 507 and CSA 22��2 No 113 (Certificate Number �225239)��** Measuring-surface sound-pressure level acc�� to DIN �N 21680�� measured at a distance of 1 m at medium inlet pressure and with connected pipes��*** �he quantities of operating liquid apply for fresh water operation without discharge liquid separator��For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid��available as accessories)��
An inlet pressure of 10 mbar abs�� can be achieved by connecting a gas ejector (seeaccessories)�� �he gas ejector can be mounted directly onto the vacuum pump��
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain�FlushingN8.7 Cavitation protection
Other voltages2�V5 131-����5 131-����-����¨ ����-¨S
50 Hz 60 Hz
3~
185…220 V �� � 320…380 V ��� � 320…380 V � � 320…380 V �220…240 V �� � 345…415 V ��� � 345…415 V � � 345…415 V �345…415 V ����500 V ����
200…254 V �� � 345…440 V ��� � 345…440 V � � 345…440 V �220…275 V �� � 380…480 V ��� � 380…480 V � � 380…480 V �380…480 V ����575 V ����
HHHH
0875
3~ ATEX Category 2G
230 V �� � 400 V ��� � 400 V � � 400 V �400 V �� � 690 V ��� � 690 V � � 690 V �500 V ����
---
DDD
165
2�V5 131 a b b1 b2 c1 c2 h1 h2 h3 h4 h5 h6 h7 h8 k l f g n s1
[mm] 801 378 300 190 20 29 175 194 249 427 372 53 76 302 373 147 608 291 103 15 x 25
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
14 382 M40x1��5 19 182 142 114 67 54 200 63 32 DN65 � 2½“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc�� to DIN 2501�� ND16 or ANSI �16��5-3-1502) suitable for round flange acc�� to DIN 2633�� ND16�� nominal width 15 or ANSI �16��5-1�2-150
Selection and ordering dataMaterials
Casing�port plate�impeller
Motor data Ser-vice-factor
Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
�eightapprox��
Fre-quency
Rated
voltage current output
Hz V A kW SF m³�h d�(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron�cast iron�bronze50 60
200��������240��220��������275��
345�������415�380�������480�
60��060��0
35��035��0
11.016.2
1��231��0
2BV5131-0KH01-8S1��81��8
7377
185
cast iron�cast iron�bronze50 60
345��������415��380��������480��
35��035��0
11.016.2
1��231��0
2BV5131-0KH01-7S1��81��8
7377
185
cast iron�cast iron�bronze50 60
500����575����
23��023��5
11.016.2
1��231��0
2BV5131-0KH01-5S1��81��8
7377
185
CrNi steel�CrNi steel�CrNi steel50 60
200��������240��220��������275��
345�������415�380�������480�
60��060��0
35��035��0
11.016.2
1��231��0
2BV5131-0HH01-8S1��81��8
7377
185
CrNi steel�CrNi steel�CrNi steel50 60
345��������415��380��������480��
35��035��0
11.016.2
1��231��0
2BV5131-0HH01-7S1��81��8
7377
185
CrNi steel�CrNi steel�CrNi steel50 60
500����575����
23��023��5
11.016.2
1��231��0
2BV5131-0HH01-5S1��81��8
7377
185
Quantity of Operating LiquidFrequency for fresh water operation � partial recirculation Inlet pressure p (abs��) ***
< 200 mbar 200 - 500 mbar > 500 mbar
Hz m³�h m³�h m³�h
50 1��8 � 0��9 0��45 � 0��4 0��4 � 0��18
60 1��8 � 0��9 0��45 � 0��4 0��4 � 0��18
Max. add. water carry-over or permissible back pressure
Frequencymax�� additionaladditionalwater carry-over
max�� permissiblepermissibleback pressure
Hz m³�h mbar abs��
50 4��5 1300
60 5��0 1300
© Gardner Denver Deutschland GmbH 2 �echn�� data sheet 2�V5 131�� edition 12�2004 �n�echn�� data sheet 2�V5 131�� edition 12�2004 �n
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron�Grey cast iron��ronze CrNi steel�CrNi steel�CrNi steel
002 CasingGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
005 Pump shaftChrome steel(X20Cr13 � 1��4021) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
035 Mechanical sealSIC � Carbon � Viton (FPM) �Chrome-nickel-molybdenum steel (�N 12756 - �Q1VGG)
SIC � Carbon � Viton (FPM) � �eflon (P�F�) sheated �Chrome-nickel-molybdenum steel (�N 12756 - Q1�M1GG)
036 �asherChrome steel(X20Cr13 � 1��4021) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 � CC33G-GS) �N 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
048�olerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 � 1��4310) �N 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 � 1��4310) �N 10088 - 2
049 Port plateGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
050 Valve plate �eflon (P�F�) �eflon (P�F�)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMo�i 18-10 � 1��4571) �N 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMo�i 18-10 � 1��4571) �N 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (N�R 70) ISO 1629 Silicone core�� �eflon (P�F�) sheated
061 CoverGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel�� lead alloyed(11SMnPb30 � 1��0718) �N 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 3
069 Sealing ring �eflon (P�F�) �eflon (P�F�)
071Pipe of cavitation protection
�eflon (P�F�) �eflon (P�F�)
072�asher for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 � 1��4301) �N 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 � 1��4301) �N 10088 - 3
079 Plug screwMachining steel�� lead alloyed(11SMnPb30 � 1��0718) �N 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 3
080 Sealing ring �eflon (P�F�) �eflon (P�F�)
© Gardner Denver Deutschland GmbH 3 �echn�� data sheet 2�V5 131�� edition 12�2004 �n�echn�� data sheet 2�V5 131�� edition 12�2004 �n
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 �ad Neustadt - Germany
info@de��gardnerdenver��comwww��gd-elmorietschle��com
�el��: +49 7622 392-0Fax: +49 7622 392-300
�el��: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve�� datas and weights without prior notice�� �he figures are without obligations��
m³/h
mbar abs.
10
mbar abs.
6
kW
20 40 60 100 1000
200
600
8
300
200 400 600
400
500
10 20 40 60 100 1000200 400 600
14
700
16
10
12
18
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Inlet pressure p1
Inlet pressure p1
© Gardner Denver Deutschland GmbH 1 �echn�� data sheet 2�V5 161�� edition 12�2004 �n�echn�� data sheet 2�V5 161�� edition 12�2004 �n
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 161 Vacuum pump
Performance curves for vacuum operation
Vacuum pumps of the L-�V5 range are suitable for evacuating gases and wet vapours down to inlet pressures of 33 mbar abs��(97% vacuum)�� All these vacuum pumps are equipped with built-in cavitation protection�� For operation below 80 mbar abs�� the cavita-tion protection should be connected to protect the vacuum pump��All pumps L-�V5 are especially space-saving in their monoblock design�� �hey are available in cast iron (standard color RAL 9006)�� �he motor is painted as standard in RAL 9006��
�he motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA�� Vacuum pumps with A��X 94�9 �G for category 2G are available�� too���he characteristics are valid for the inlet of air with a relative humidity of 100 % and a temperature of 20 °C�� compression to 1013 mbar abs�� and water at 15 °C as operating liquid�� �he tolerance is ± 10 %��
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
�he motors are designed according to DIN �N 60 034 � DIN I�C 34-1 andtemperature class F�� For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range��For all three phase machines according to UL and CSA norm (UL 507 and CSA 22��2 No�� 100) the maximum allowed voltage tolerances are -10 % resp�� +6 %�� �he frequency tolerance is maximum ± 2 %��
All L-�V5 achieve the standards and norms of the low voltage directive 72�23���G��L-�V5 achieve the standards and norms of the low voltage directive 72�23���G���V5 achieve the standards and norms of the low voltage directive 72�23���G��rotating electrotechnical motor �N 60034-1-34�� electromagnetic compatibility (�MC)DIN �N 61000-0�-6�-4��
* For standard UL 507 and CSA 22��2 No 113 (Certificate Number �225239)��** Measuring-surface sound-pressure level acc�� to DIN �N 21680�� measured at a distance of 1 m at medium inlet pressure and with connected pipes��*** �he quantities of operating liquid apply for fresh water operation without discharge liquid separator��For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid��available as accessories)��
An inlet pressure of 10 mbar abs�� can be achieved by connecting a gas ejector (seeaccessories)�� �he gas ejector can be mounted directly onto the vacuum pump��
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain�FlushingN8.7 Cavitation protection
Other voltages2�V5 161-����5 161-����-����¨ ����-¨S
50 Hz 60 Hz
3~
185…220 V �� � 320…380 V ��� � 320…380 V � � 320…380 V �220…240 V �� � 345…415 V ��� � 345…415 V � � 345…415 V �345…415 V ����500 V ����
200…254 V �� � 345…440 V ��� � 345…440 V � � 345…440 V �220…275 V �� � 380…480 V ��� � 380…480 V � � 380…480 V �380…480 V ����575 V ����
HHHH
0875
3~ ATEX Category 2G
230 V �� � 400 V ��� � 400 V � � 400 V �400 V �� � 690 V ��� � 690 V � � 690 V �500 V ����
---
DDD
165
2�V5 161 a b b1 b2 c1 c2 h1 h2 h3 3) h4 h5 h6 h7 h8 k l f g n s1
[mm] 1009 481 370 188 30 29 210 225 303 427 372 53 76 302 617 201 772 412 137 15 x 27
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
15 450 M40 x1��5 22 200 156 130 80 75 250 81 41 DN80 � 3“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc�� to DIN 2501�� ND16 or ANSI �16��5-3-1502) suitable for round flange acc�� to DIN 2633�� ND16�� nominal width 15 or ANSI �16��5-1�2-1503) for 2�V5 161-��H������ h3 = 305
Selection and ordering dataMaterials
Casing�port plate�impeller
Motor data Ser-vice-factor
Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
�eightapprox��
Fre-quency
Rated
voltage current output
Hz V A kW SF m³�h d�(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron�cast iron�bronze50 60
200��������240��220��������275��
345�������415�380�������480�
66��069��0
38��040��0
12.018.0
1��251��0
2BV5161-0KH02-8S2��42��4
7475
260
cast iron�cast iron�bronze50 60
345��������415��380��������480��
38��040��0
12.018.0
1��251��0
2BV5161-0KH02-7S2��42��4
7475
260
cast iron�cast iron�bronze50 60
500����575����
25��225��6
12.018.0
1��251��0
2BV5161-0KH02-5S2��42��4
7475
260
CrNi steel�CrNi steel�CrNi steel50 60
200��������240��220��������275��
345�������415�380�������480�
66��069��0
38��040��0
12.018.0
1��251��0
2BV5161-0HH02-8S2��42��4
7475
260
CrNi steel�CrNi steel�CrNi steel50 60
345��������415��380��������480��
38��040��0
12.018.0
1��251��0
2BV5161-0HH02-7S2��42��4
7475
260
CrNi steel�CrNi steel�CrNi steel50 60
500����575����
25��225��6
12.018.0
1��251��0
2BV5161-0HH02-5S2��42��4
7475
260
Quantity of Operating LiquidFrequency for fresh water operation � partial recirculation Inlet pressure p (abs��) ***
< 200 mbar 200 - 500 mbar > 500 mbar
Hz m³�h m³�h m³�h
50 2��4 � 1��2 0��7 � 0��6 0��5 � 0��25
60 2��4 � 1��2 0��7 � 0��6 0��5 � 0��25
Max. add. water carry-over or permissible back pressure
Frequencymax�� additionaladditionalwater carry-over
max�� permissiblepermissibleback pressure
Hz m³�h mbar abs��
50 3��0 1300
60 3��0 1300
© Gardner Denver Deutschland GmbH 2 �echn�� data sheet 2�V5 161�� edition 12�2004 �n�echn�� data sheet 2�V5 161�� edition 12�2004 �n
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron�Grey cast iron��ronze CrNi steel�CrNi steel�CrNi steel
002 CasingGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
005 Pump shaftChrome steel(X20Cr13 � 1��4021) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
035 Mechanical sealSIC � Carbon � Viton (FPM) �Chrome-nickel-molybdenum steel (�N 12756 - �Q1VGG)
SIC � Carbon � Viton (FPM) � �eflon (P�F�) sheated �Chrome-nickel-molybdenum steel (�N 12756 - Q1�M1GG)
036 �asherChrome steel(X20Cr13 � 1��4021) �N 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMo�i 17-12-2 � 1��4571) �N 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 � CC33G-GS) �N 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
048�olerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 � 1��4310) �N 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 � 1��4310) �N 10088 - 2
049 Port plateGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
050 Valve plate �eflon (P�F�) �eflon (P�F�)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMo�i 18-10 � 1��4571) �N 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMo�i 18-10 � 1��4571) �N 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (N�R 70) ISO 1629 Silicone core�� �eflon (P�F�) sheated
061 CoverGrey cast iron(�N-GJL H� 195 � �N-JL2030) �N 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 � 1��4581) �N 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel�� lead alloyed(11SMnPb30 � 1��0718) �N 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 3
069 Sealing ring �eflon (P�F�) �eflon (P�F�)
071Pipe of cavitation protection
�eflon (P�F�) �eflon (P�F�)
072�asher for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 � 1��4301) �N 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 � 1��4301) �N 10088 - 3
079 Plug screwMachining steel�� lead alloyed(11SMnPb30 � 1��0718) �N 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 � 1��4401) �N 10088 - 3
080 Sealing ring �eflon (P�F�) �eflon (P�F�)
© Gardner Denver Deutschland GmbH 3 �echn�� data sheet 2�V5 161�� edition 12�2004 �n�echn�� data sheet 2�V5 161�� edition 12�2004 �n
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 �ad Neustadt - Germany
info@de��gardnerdenver��comwww��gd-elmorietschle��com
�el��: +49 7622 392-0Fax: +49 7622 392-300
�el��: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve�� datas and weights without prior notice�� �he figures are without obligations��
0
m³/h
mbar abs.
1000
mbar abs.
0
kW
50
1200 1400 1600 1800 2000 2200
100
150
200
2
4
6
8
10
1000 1200 1400 1600 1800 2000 2200
250
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Discharge pressure p2
The characteristics are valid for the inlet of air with a relative humidity of 50 % and a temperature of 20 °C at a atmospheric pressure of 1013 mbar abs. and water at 15 °C as operating liquid.The tolerance is ± 10 %.
The motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA. Compressors with ATEX 94/9 EG for category 2G are available, too.
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Discharge pressure p2
7.5 kW
8.6 kW
6.2 kW
5.3 kW
7.5 kW
8.6 kW
6.2 kW
5.3 kW
© Gardner Denver Deutschland GmbH 1 Techn. data sheet 2BV5 110, edition 06/2005 En
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 110 Compressor
Performance curves for compressor operation
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
Selection and ordering dataMaterials
Casing/port plate/impeller
Motor data Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
Weightapprox.
Fre-quency
Rated
voltage current output
Hz V A kW m³/h dB(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron/cast iron/bronze50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
19.020.0
11.011.5
5.36.2
2BV5110-8KH01-8S0.90.9
6771
86
cast iron/cast iron/bronze50 60
345Δ...415Δ380Δ...480Δ
11.011.5
5.36.2
2BV5110-8KH01-7S0.90.9
6771
86
cast iron/cast iron/bronze50 60
500ΔΔ575ΔΔ
9.09.2
5.36.2
2BV5110-8KH01-5S0.90.9
6771
86
CrNi steel/CrNi steel/CrNi steel50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
19,020,0
11.011.5
5.36.2
2BV5110-8HH01-8S0.90.9
6771
86
CrNi steel/CrNi steel/CrNi steel50 60
345Δ...415Δ380Δ...480Δ
11.011.5
5.36.2
2BV5110-8HH01-7S0.90.9
6771
86
CrNi steel/CrNi steel/CrNi steel50 60
500ΔΔ575ΔΔ
9.09.2
5.36.2
2BV5110-8HH01-5S0.90.9
6771
86
cast iron/cast iron/bronze50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
27.527.5
16.016.0
7.58.6
2BV5110-8KH03-8S0.90.9
6974
98
cast iron/cast iron/bronze50 60
345Δ...415Δ380Δ...480Δ
16.016.0
7.58.6
2BV5110-8KH03-7S0.90.9
6974
98
cast iron/cast iron/bronze50 60
500ΔΔ575ΔΔ
12.512.8
7.58.6
2BV5110-8KH03-5S0.90.9
6974
98
CrNi steel/CrNi steel/CrNi steel50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
27.527.5
16.016.0
7.58.6
2BV5110-8HH03-8S0.90.9
6974
98
CrNi steel/CrNi steel/CrNi steel50 60
345Δ...415Δ380Δ...480Δ
16.016.0
7.58.6
2BV5110-8HH03-7S0.90.9
6974
98
CrNi steel/CrNi steel/CrNi steel50 60
500ΔΔ575ΔΔ
12.512.8
7.58.6
2BV5110-8HH03-5S0.90.9
6974
98
Quantity of Operating LiquidFrequency for fresh water operation
at Inlet pressure ***
Hz m³/h
50 0.9
60 0.9
The motors are designed according to DIN EN 60 034 / DIN IEC 34-1 andtemperature class F. For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range.For all three phase machines according to UL and CSA norm (UL 507 and CSA 22.2 No. 100) the maximum allowed voltage tolerances are -10 % resp. +6 %. The frequency tolerance is maximum ± 2 %.
All L-BV5 achieve the standards and norms of the low voltage directive 72/23/EWG,L-BV5 achieve the standards and norms of the low voltage directive 72/23/EWG,BV5 achieve the standards and norms of the low voltage directive 72/23/EWG,rotating electrotechnical motor EN 60034-1-34, electromagnetic compatibility (EMC)DIN EN 61000-0/-6/-4.
* For standard UL 507 and CSA 22.2 No 113 (Certificate Number E225239).** Measuring-surface sound-pressure level acc. to DIN EN 21680, measured at a distance of 1 m at medium inlet pressure and with connected pipes.*** The quantities of operating liquid apply for fresh water operation without discharge liquid separator.For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid,available as accessories).
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain/FlushingN8.7 Cavitation protection
Other voltages2BV5 110-..5 110-..-..¨ ..-¨S
50 Hz 60 Hz
3~
185…220 V Δ / 320…380 V YΔ / 320…380 V Y / 320…380 V Y220…240 V Δ / 345…415 V YΔ / 345…415 V Y / 345…415 V Y345…415 V ΔΔ500 V ΔΔ
200…254 V Δ / 345…440 V YΔ / 345…440 V Y / 345…440 V Y220…275 V Δ / 380…480 V YΔ / 380…480 V Y / 380…480 V Y380…480 V ΔΔ575 V ΔΔ
HHHH
0875
3~ ATEX Category 2G
230 V Δ / 400 V YΔ / 400 V Y / 400 V Y400 V Δ / 690 V YΔ / 690 V Y / 690 V Y500 V ΔΔ
---
DDD
165
---
460 V ΔΔ460 V Y575 V Δ
GGG
615
2BV5 110 a b b1 b2 c1 c2 h1 h2 h3 h4 h5 h6 h7 h8 k l f g n s1
[mm] 639 326 255 190 20 26 140 153 203 361 288 38 58 231 295 129 468 208 91 12 x 23
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
12 340 M32x1.5 19 160 123 97 52 42 180 52 25 DN50 / 2“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc. to DIN 2501, ND16 or ANSI B16.5-3-1502) suitable for round flange acc. to DIN 2633, ND16, nominal width 15 or ANSI B16.5-1/2-150
© Gardner Denver Deutschland GmbH 2 Techn. data sheet 2BV5 110, edition 06/2005 En
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron/Grey cast iron/Bronze CrNi steel/CrNi steel/CrNi steel
002 CasingGrey cast iron(EN-GJL HB 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
005 Pump shaftChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
035 Mechanical sealSIC / Carbon / Viton (FPM) /Chrome-nickel-molybdenum steel (EN 12756 - BQ1VGG)
SIC / Carbon / Viton (FPM) / Teflon (PTFE) sheated /Chrome-nickel-molybdenum steel (EN 12756 - Q1BM1GG)
036 WasherChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 / CC33G-GS) EN 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
048Tolerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
049 Port plateGrey cast iron(EN-GJL HB 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
050 Valve plate Teflon (PTFE) Teflon (PTFE)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (NBR 70) ISO 1629 Silicone core, Teflon (PTFE) sheated
061 CoverGrey cast iron(EN-GJL HB 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
069 Sealing ring Teflon (PTFE) Teflon (PTFE)
071Pipe of cavitation protection
Teflon (PTFE) Teflon (PTFE)
072Washer for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
079 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
080 Sealing ring Teflon (PTFE) Teflon (PTFE)
© Gardner Denver Deutschland GmbH 3 Techn. data sheet 2BV5 110, edition 06/2005 En
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 Bad Neustadt - Germany
Tel.: +49 7622 392-0Fax: +49 7622 392-300
Tel.: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve, datas and weights without prior notice. The figures are without obligations.
0
m³/h
mbar abs.
1000
mbar abs.
0
kW
50
1200 1400 1600 1800 2000
100
150
200
2
4
6
8
10
1000 1200 1400 1600 1800 2000
250
300
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Discharge pressure p2
The characteristics are valid for the inlet of air with a relative humidity of 50 % and a temperature of 20 °C at a atmospheric pressure of 1013 mbar abs. and water at 15 °C as operating liquid.The tolerance is ± 10 %.
The motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA. Compressors with ATEX 94/9 EG for category 2G are available, too.
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Discharge pressure p2
7.0 kW
8.2 kW
7.0 kW
8.2 kW
© Gardner Denver Deutschland GmbH 1 Techn. data sheet 2�V5 111, edition 06/2005 EnTechn. data sheet 2�V5 111, edition 06/2005 En
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 111 Compressor
Performance curves for compressor operation
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
Selection and ordering dataMaterials
Casing/port plate/impeller
Motor data Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
Weightapprox.
Fre-quency
Rated
voltage current output
Hz V A kW m³/h d�(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron/cast iron/bronze50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
27.527.5
16.016.0
7.08.2
2BV5111-8KH03-8S1.21.2
6973
105
cast iron/cast iron/bronze50 60
345Δ...415Δ380Δ...480Δ
16.016.0
7.08.2
2BV5111-8KH03-7S1.21.2
6973
105
cast iron/cast iron/bronze50 60
500ΔΔ575ΔΔ
12.512.8
7.08.2
2BV5111-8KH03-5S1.21.2
6973
105
CrNi steel/CrNi steel/CrNi steel50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
27.527.5
16.016.0
7.08.2
2BV5111-8HH03-8S1.21.2
6973
105
CrNi steel/CrNi steel/CrNi steel50 60
345Δ...415Δ380Δ...480Δ
16.016.0
7.08.2
2BV5111-8HH03-7S1.21.2
6973
105
CrNi steel/CrNi steel/CrNi steel50 60
500ΔΔ575ΔΔ
12.512.8
7.08.2
2BV5111-8HH03-5S1.21.2
6973
105
Quantity of Operating LiquidFrequency for fresh water operation
at Inlet pressure ***
Hz m³/h
50 1.2
60 1.2
The motors are designed according to DIN EN 60 034 / DIN IEC 34-1 andtemperature class F. For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range.For all three phase machines according to UL and CSA norm (UL 507 and CSA 22.2 No. 100) the maximum allowed voltage tolerances are -10 % resp. +6 %. The frequency tolerance is maximum ± 2 %.
All L-�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,rotating electrotechnical motor EN 60034-1-34, electromagnetic compatibility (EMC)DIN EN 61000-0/-6/-4.
* For standard UL 507 and CSA 22.2 No 113 (Certificate Number E225239).** Measuring-surface sound-pressure level acc. to DIN EN 21680, measured at a distance of 1 m at medium inlet pressure and with connected pipes.*** The quantities of operating liquid apply for fresh water operation without discharge liquid separator.For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid,available as accessories).
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain/FlushingN8.7 Cavitation protection
Other voltages2�V5 111-..5 111-..-..¨ ..-¨S
50 Hz 60 Hz
3~
185…220 V Δ / 320…380 V YΔ / 320…380 V Y / 320…380 V Y220…240 V Δ / 345…415 V YΔ / 345…415 V Y / 345…415 V Y345…415 V ΔΔ500 V ΔΔ
200…254 V Δ / 345…440 V YΔ / 345…440 V Y / 345…440 V Y220…275 V Δ / 380…480 V YΔ / 380…480 V Y / 380…480 V Y380…480 V ΔΔ575 V ΔΔ
HHHH
0875
3~ ATEX Category 2G
230 V Δ / 400 V YΔ / 400 V Y / 400 V Y400 V Δ / 690 V YΔ / 690 V Y / 690 V Y500 V ΔΔ
---
DDD
165
2�V5 111 a b b1 b2 c1 c2 h1 h2 h3 h4 h5 h6 h7 h8 k l f g n s1
[mm] 653 326 265 190 20 26 151 166 213 371 318 48 68 258 291 128 482 224 91 12 x 23
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
12 340 M32x1.5 19 160 123 97 52 42 180 52 27 DN50 / 2“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc. to DIN 2501, ND16 or ANSI �16.5-3-1502) suitable for round flange acc. to DIN 2633, ND16, nominal width 15 or ANSI �16.5-1/2-150
© Gardner Denver Deutschland GmbH 2 Techn. data sheet 2�V5 111, edition 06/2005 EnTechn. data sheet 2�V5 111, edition 06/2005 En
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron/Grey cast iron/�ronze CrNi steel/CrNi steel/CrNi steel
002 CasingGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
005 Pump shaftChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
035 Mechanical sealSIC / Carbon / Viton (FPM) /Chrome-nickel-molybdenum steel (EN 12756 - �Q1VGG)
SIC / Carbon / Viton (FPM) / Teflon (PTFE) sheated /Chrome-nickel-molybdenum steel (EN 12756 - Q1�M1GG)
036 WasherChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 / CC33G-GS) EN 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
048Tolerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
049 Port plateGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
050 Valve plate Teflon (PTFE) Teflon (PTFE)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (N�R 70) ISO 1629 Silicone core, Teflon (PTFE) sheated
061 CoverGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
069 Sealing ring Teflon (PTFE) Teflon (PTFE)
071Pipe of cavitation protection
Teflon (PTFE) Teflon (PTFE)
072Washer for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
079 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
080 Sealing ring Teflon (PTFE) Teflon (PTFE)
© Gardner Denver Deutschland GmbH 3 Techn. data sheet 2�V5 111, edition 06/2005 EnTechn. data sheet 2�V5 111, edition 06/2005 En
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 �ad Neustadt - Germany
Tel.: +49 7622 392-0Fax: +49 7622 392-300
Tel.: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve, datas and weights without prior notice. The figures are without obligations.
0
m³/h
mbar abs.
1000
mbar abs.
0
kW
1200 1400 1600 1800 2000
100
300
200
4
8
12
400
2200
1000 1200 1400 1600 1800 2000 2200
16
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Discharge pressure p2
The characteristics are valid for the inlet of air with a relative humidity of 50 % and a temperature of 20 °C at a atmospheric pressure of 1013 mbar abs. and water at 15 °C as operating liquid.The tolerance is ± 10 %.
The motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA. Compressors with ATEX 94/9 EG for category 2G are available, too.
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Discharge pressure p2
© Gardner Denver Deutschland GmbH 1 Techn. data sheet 2�V5 121, edition 06/2005 EnTechn. data sheet 2�V5 121, edition 06/2005 En
15.0 kW
9.75 kW
11.4 kW
17.3 kW
11.4 kW
17.3 kW
9.75 kW 15.0 kW
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 121 Compressor
Performance curves for compressor operation
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
Selection and ordering dataMaterials
Casing/port plate/impeller
Motor data Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
Weightapprox.
Fre-quency
Rated
voltage current output
Hz V A kW m³/h d�(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron/cast iron/bronze50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
38.039.0
22.022.5
9.7511.4
2BV5121-8KH03-8S1.51.5
7376
165
cast iron/cast iron/bronze50 60
345Δ...415Δ380Δ...480Δ
21.021.5
9.7511.4
2BV5121-8KH03-7S1.51.5
7376
165
cast iron/cast iron/bronze50 60
500ΔΔ575ΔΔ
16.016.5
9.7511.4
2BV5121-8KH03-5S1.51.5
7376
165
CrNi steel/CrNi steel/CrNi steel50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
38.039.0
22.022.5
9.7511.4
2BV5121-8HH03-8S1.51.5
7376
165
CrNi steel/CrNi steel/CrNi steel50 60
345Δ...415Δ380Δ...480Δ
21.021.5
9.7511.4
2BV5121-8HH03-7S1.51.5
7376
165
CrNi steel/CrNi steel/CrNi steel50 60
500ΔΔ575ΔΔ
16.016.5
9.7511.4
2BV5121-8HH03-5S1.51.5
7376
165
cast iron/cast iron/bronze50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
60.060.0
35.035.0
15.017.3
2BV5121-8KH04-8S1.51.5
7578
190
cast iron/cast iron/bronze50 60
345Δ...415Δ380Δ...480Δ
35.035.0
15.017.3
2BV5121-8KH04-7S1.51.5
7578
190
cast iron/cast iron/bronze50 60
500ΔΔ575ΔΔ
23.023.5
15.017.3
2BV5121-8KH04-5S1.51.5
7578
190
CrNi steel/CrNi steel/CrNi steel50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
60.060.0
35.035.0
15.017.3
2BV5121-8HH04-8S1.51.5
7578
190
CrNi steel/CrNi steel/CrNi steel50 60
345Δ...415Δ380Δ...480Δ
35.035.0
15.017.3
2BV5121-8HH04-7S1.51.5
7578
190
CrNi steel/CrNi steel/CrNi steel50 60
500ΔΔ575ΔΔ
23.023.5
15.017.3
2BV5121-8HH04-5S1.51.5
7578
190
Quantity of Operating LiquidFrequency for fresh water operation
at Inlet pressure ***
Hz m³/h
50 1.5
60 1.5
The motors are designed according to DIN EN 60 034 / DIN IEC 34-1 andtemperature class F. For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range.For all three phase machines according to UL and CSA norm (UL 507 and CSA 22.2 No. 100) the maximum allowed voltage tolerances are -10 % resp. +6 %. The frequency tolerance is maximum ± 2 %.
All L-�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,L-�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,rotating electrotechnical motor EN 60034-1-34, electromagnetic compatibility (EMC)DIN EN 61000-0/-6/-4.
* For standard UL 507 and CSA 22.2 No 113 (Certificate Number E225239).** Measuring-surface sound-pressure level acc. to DIN EN 21680, measured at a distance of 1 m at medium inlet pressure and with connected pipes.*** The quantities of operating liquid apply for fresh water operation without discharge liquid separator.For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid,available as accessories).
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain/FlushingN8.7 Cavitation protection
Other voltages2�V5 121-..5 121-..-..¨ ..-¨S
50 Hz 60 Hz
3~
185…220 V Δ / 320…380 V YΔ / 320…380 V Y / 320…380 V Y220…240 V Δ / 345…415 V YΔ / 345…415 V Y / 345…415 V Y345…415 V ΔΔ500 V ΔΔ
200…254 V Δ / 345…440 V YΔ / 345…440 V Y / 345…440 V Y220…275 V Δ / 380…480 V YΔ / 380…480 V Y / 380…480 V Y380…480 V ΔΔ575 V ΔΔ
HHHH
0875
3~ ATEX Category 2G
230 V Δ / 400 V YΔ / 400 V Y / 400 V Y400 V Δ / 690 V YΔ / 690 V Y / 690 V Y500 V ΔΔ
---
DDD
165
---
460 V ΔΔ460 V Y575 V ΔΔ
GGG
615
2�V5 121 a b b1 b2 c1 c2 h1 h2 h3 h4 h5 h6 h7 h8 k l f g n s1
[mm] 752 348 265 190 20 26 151 167 217 385 318 39 60 258 336 135 565 262 96 12 x 23
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
12 382 M32x1.5 19 182 142 114 67 42 200 57 29 DN65 / 2½“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc. to DIN 2501, ND16 or ANSI �16.5-3-1502) suitable for round flange acc. to DIN 2633, ND16, nominal width 15 or ANSI �16.5-1/2-150
© Gardner Denver Deutschland GmbH 2 Techn. data sheet 2�V5 121, edition 06/2005 EnTechn. data sheet 2�V5 121, edition 06/2005 En
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron/Grey cast iron/�ronze CrNi steel/CrNi steel/CrNi steel
002 CasingGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
005 Pump shaftChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
035 Mechanical sealSIC / Carbon / Viton (FPM) /Chrome-nickel-molybdenum steel (EN 12756 - �Q1VGG)
SIC / Carbon / Viton (FPM) / Teflon (PTFE) sheated /Chrome-nickel-molybdenum steel (EN 12756 - Q1�M1GG)
036 WasherChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 / CC33G-GS) EN 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
048Tolerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
049 Port plateGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
050 Valve plate Teflon (PTFE) Teflon (PTFE)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (N�R 70) ISO 1629 Silicone core, Teflon (PTFE) sheated
061 CoverGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
069 Sealing ring Teflon (PTFE) Teflon (PTFE)
071Pipe of cavitation protection
Teflon (PTFE) Teflon (PTFE)
072Washer for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
079 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
080 Sealing ring Teflon (PTFE) Teflon (PTFE)
© Gardner Denver Deutschland GmbH 3 Techn. data sheet 2�V5 121, edition 06/2005 EnTechn. data sheet 2�V5 121, edition 06/2005 En
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 �ad Neustadt - Germany
Tel.: +49 7622 392-0Fax: +49 7622 392-300
Tel.: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve, datas and weights without prior notice. The figures are without obligations.
m³/h
mbar abs.
1000
mbar abs.
0
kW
1200 1400 1600 1800
250
300
350
5
15
400
20
450
500
10
1000 1200 1400 1600 1800
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Discharge pressure p2
The characteristics are valid for the inlet of air with a relative humidity of 50 % and a temperature of 20 °C at a atmospheric pressure of 1013 mbar abs. and water at 15 °C as operating liquid.The tolerance is ± 10 %.
The motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA. Compressors with ATEX 94/9 EG for category 2G are available, too.
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Discharge pressure p2
© Gardner Denver Deutschland GmbH 1 Techn. data sheet 2�V5 131, edition 06/2005 EnTechn. data sheet 2�V5 131, edition 06/2005 En
16.2 kW
13.5 kW
16.2 kW
13.5 kW
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 131 Compressor
Performance curves for compressor operation
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
Selection and ordering dataMaterials
Casing/port plate/impeller
Motor data Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
Weightapprox.
Fre-quency
Rated
voltage current output
Hz V A kW m³/h d�(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron/cast iron/bronze50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
60.060.0
35.035.0
13.516.5
2BV5131-8KH01-8S1.81.8
7678
185
cast iron/cast iron/bronze50 60
345Δ...415Δ380Δ...480Δ
35.035.0
13.516.5
2BV5131-8KH01-7S1.81.8
7678
185
cast iron/cast iron/bronze50 60
500ΔΔ575ΔΔ
23.023.5
13.516.5
2BV5131-8KH01-5S1.81.8
7678
185
CrNi steel/CrNi steel/CrNi steel50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
60.060.0
35.035.0
13.516.5
2BV5131-8HH01-8S1.81.8
7678
185
CrNi steel/CrNi steel/CrNi steel50 60
345Δ...415Δ380Δ...480Δ
35.035.0
13.516.5
2BV5131-8HH01-7S1.81.8
7678
185
CrNi steel/CrNi steel/CrNi steel50 60
500ΔΔ575ΔΔ
23.023.5
13.516.5
2BV5131-8HH01-5S1.81.8
7678
185
Quantity of Operating LiquidFrequency for fresh water operation
at Inlet pressure ***
Hz m³/h
50 1.8
60 1.8
The motors are designed according to DIN EN 60 034 / DIN IEC 34-1 andtemperature class F. For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range.For all three phase machines according to UL and CSA norm (UL 507 and CSA 22.2 No. 100) the maximum allowed voltage tolerances are -10 % resp. +6 %. The frequency tolerance is maximum ± 2 %.
All L-�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,L-�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,rotating electrotechnical motor EN 60034-1-34, electromagnetic compatibility (EMC)DIN EN 61000-0/-6/-4.
* For standard UL 507 and CSA 22.2 No 113 (Certificate Number E225239).** Measuring-surface sound-pressure level acc. to DIN EN 21680, measured at a distance of 1 m at medium inlet pressure and with connected pipes.*** The quantities of operating liquid apply for fresh water operation without discharge liquid separator.For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid,available as accessories).
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain/FlushingN8.7 Cavitation protection
Other voltages2�V5 131-..5 131-..-..¨ ..-¨S
50 Hz 60 Hz
3~
185…220 V Δ / 320…380 V YΔ / 320…380 V Y / 320…380 V Y220…240 V Δ / 345…415 V YΔ / 345…415 V Y / 345…415 V Y345…415 V ΔΔ500 V ΔΔ
200…254 V Δ / 345…440 V YΔ / 345…440 V Y / 345…440 V Y220…275 V Δ / 380…480 V YΔ / 380…480 V Y / 380…480 V Y380…480 V ΔΔ575 V ΔΔ
HHHH
0875
3~ ATEX Category 2G
230 V Δ / 400 V YΔ / 400 V Y / 400 V Y400 V Δ / 690 V YΔ / 690 V Y / 690 V Y500 V ΔΔ
---
DDD
165
2�V5 131 a b b1 b2 c1 c2 h1 h2 h3 h4 h5 h6 h7 h8 k l f g n s1
[mm] 801 378 300 190 20 29 175 194 249 427 372 53 76 302 373 147 608 291 103 15 x 25
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
14 382 M40x1.5 19 182 142 114 67 54 200 63 32 DN65 / 2½“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc. to DIN 2501, ND16 or ANSI �16.5-3-1502) suitable for round flange acc. to DIN 2633, ND16, nominal width 15 or ANSI �16.5-1/2-150
© Gardner Denver Deutschland GmbH 2 Techn. data sheet 2�V5 131, edition 06/2005 EnTechn. data sheet 2�V5 131, edition 06/2005 En
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron/Grey cast iron/�ronze CrNi steel/CrNi steel/CrNi steel
002 CasingGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
005 Pump shaftChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
035 Mechanical sealSIC / Carbon / Viton (FPM) /Chrome-nickel-molybdenum steel (EN 12756 - �Q1VGG)
SIC / Carbon / Viton (FPM) / Teflon (PTFE) sheated /Chrome-nickel-molybdenum steel (EN 12756 - Q1�M1GG)
036 WasherChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 / CC33G-GS) EN 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
048Tolerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
049 Port plateGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
050 Valve plate Teflon (PTFE) Teflon (PTFE)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (N�R 70) ISO 1629 Silicone core, Teflon (PTFE) sheated
061 CoverGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
069 Sealing ring Teflon (PTFE) Teflon (PTFE)
071Pipe of cavitation protection
Teflon (PTFE) Teflon (PTFE)
072Washer for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
079 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
080 Sealing ring Teflon (PTFE) Teflon (PTFE)
© Gardner Denver Deutschland GmbH 3 Techn. data sheet 2�V5 131, edition 06/2005 EnTechn. data sheet 2�V5 131, edition 06/2005 En
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 �ad Neustadt - Germany
Tel.: +49 7622 392-0Fax: +49 7622 392-300
Tel.: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve, datas and weights without prior notice. The figures are without obligations.
m³/h
mbar abs.
1000
mbar abs.
0
kW
1200 1400 1600 2000
300
400
500
5
15
20
600
700
10
1800
1000 1200 1400 1600 20001800
60 Hz50 Hz
60 Hz50 Hz
Suc
tion
cap
acity
V
Discharge pressure p2
The characteristics are valid for the inlet of air with a relative humidity of 50 % and a temperature of 20 °C at a atmospheric pressure of 1013 mbar abs. and water at 15 °C as operating liquid.The tolerance is ± 10 %.
The motors are supplied as standard for the input voltage ranges of 50 and 60 Hz and for the protection category IP55 as well as approbated for UL and CSA. Compressors with ATEX 94/9 EG for category 2G are available, too.
Pow
er r
equi
rem
ent
Pon
the
pum
p s
haft
Discharge pressure p2
© Gardner Denver Deutschland GmbH 1 Techn. data sheet 2�V5 161, edition 06/2005 EnTechn. data sheet 2�V5 161, edition 06/2005 En
18.0 kW
15.0 kW
18.0 kW
15.0 kW
Data sheet liquidring pump
Series L-BV5 | L_300
Range 2BV5 161 Compressor
Performance curves for compressor operation
N2.0 N2.0
N8.7 N8.7
N4.2 N4.2
N3.0N3.0
N3.0 (nur • only 2BV5 ...-0H.)
N1.0 N1.0
N1.0, N2.0
2BV5 ...-0H.2BV5 ...-0K.
Selection and ordering dataMaterials
Casing/port plate/impeller
Motor data Order-No. Quantity ofoperatingliquid
Soundpressurelevel **
Weightapprox.
Fre-quency
Rated
voltage current output
Hz V A kW m³/h d�(A) kg
3~ 50/60 Hz version, protection class IP 55, insulation class F *
cast iron/cast iron/bronze50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
66.069.0
38.040.0
15.018.0
2BV5161-8KH02-8S 2.47778
260
cast iron/cast iron/bronze50 60
345Δ...415Δ380Δ...480Δ
38.040.0
15.018.0
2BV5161-8KH02-7S 2.47778
260
cast iron/cast iron/bronze50 60
500ΔΔ575ΔΔ
25.225.6
15.018.0
2BV5161-8KH02-5S 2.47778
260
CrNi steel/CrNi steel/CrNi steel50 60
200Δ...240Δ220Δ...275Δ
345Y...415Y380Y...480Y
66.069.0
38.040.0
15.018.0
2BV5161-8HH02-8S 2.47778
260
CrNi steel/CrNi steel/CrNi steel50 60
345Δ...415Δ380Δ...480Δ
38.040.0
15.018.0
2BV5161-8HH02-7S 2.47778
260
CrNi steel/CrNi steel/CrNi steel50 60
500ΔΔ575ΔΔ
25.225.6
15.018.0
2BV5161-8HH02-5S 2.47778
260
Quantity of Operating LiquidFrequency for fresh water operation
at Inlet pressure ***
Hz m³/h
50 2.4
60 2.4
The motors are designed according to DIN EN 60 034 / DIN IEC 34-1 andtemperature class F. For the three phase machines the tolerances are ± 10 % for fixed voltage and ± 5 % for voltage range.For all three phase machines according to UL and CSA norm (UL 507 and CSA 22.2 No. 100) the maximum allowed voltage tolerances are -10 % resp. +6 %. The frequency tolerance is maximum ± 2 %.
All L-�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,L-�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,�V5 achieve the standards and norms of the low voltage directive 72/23/EWG,rotating electrotechnical motor EN 60034-1-34, electromagnetic compatibility (EMC)DIN EN 61000-0/-6/-4.
* For standard UL 507 and CSA 22.2 No 113 (Certificate Number E225239).** Measuring-surface sound-pressure level acc. to DIN EN 21680, measured at a distance of 1 m at medium inlet pressure and with connected pipes.*** The quantities of operating liquid apply for fresh water operation without discharge liquid separator.For partial recirculation operation the quantity of the fresh applied refrigerantcan be reduced by circulation of the operating liquid in a circuit (withdischarge liqiud separator and internal recirculation of the operating liquid,available as accessories).
N1.0 Inlet flangeN2.0 Pressure flangeN3.0 Connection operating liquidN4.2 Drain/FlushingN8.7 Cavitation protection
Other voltages2�V5 161-..5 161-..-..¨ ..-¨S
50 Hz 60 Hz
3~
185…220 V Δ / 320…380 V YΔ / 320…380 V Y / 320…380 V Y220…240 V Δ / 345…415 V YΔ / 345…415 V Y / 345…415 V Y345…415 V ΔΔ500 V ΔΔ
200…254 V Δ / 345…440 V YΔ / 345…440 V Y / 345…440 V Y220…275 V Δ / 380…480 V YΔ / 380…480 V Y / 380…480 V Y380…480 V ΔΔ575 V ΔΔ
HHHH
0875
3~ ATEX Category 2G
230 V Δ / 400 V YΔ / 400 V Y / 400 V Y400 V Δ / 690 V YΔ / 690 V Y / 690 V Y500 V ΔΔ
---
DDD
165
2�V5 161 a b b1 b2 c1 c2 h1 h2 h3 3) h4 h5 h6 h7 h8 k l f g n s1
[mm] 1009 481 370 188 30 29 210 225 303 427 372 53 76 302 617 201 772 412 137 15 x 27
s2 t v d1 d2 d3 d4 d5 w w1 w2 w3 d1) (N1.0, N2.0) N3.0 2) N4.2 N8.7
15 450 M40 x1.5 22 200 156 130 80 75 250 81 41 DN80 / 3“ G¾ x 24 G³⁄8 x 25 G³⁄8 x 11
1) suitable for mating flange acc. to DIN 2501, ND16 or ANSI �16.5-3-1502) suitable for round flange acc. to DIN 2633, ND16, nominal width 15 or ANSI �16.5-1/2-1503) for 2�V5 161-.H... h3 = 305
© Gardner Denver Deutschland GmbH 2 Techn. data sheet 2�V5 161, edition 06/2005 EnTechn. data sheet 2�V5 161, edition 06/2005 En
Dimensions
006
049
069
061071
072
063
036048
080
051
068
050
047
058
002005
035
037
079
Exploded drawing
Materials of construction
Part-No.
Designation Material combination
Grey cast iron/Grey cast iron/�ronze CrNi steel/CrNi steel/CrNi steel
002 CasingGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
005 Pump shaftChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
006 Feather keyChrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
035 Mechanical sealSIC / Carbon / Viton (FPM) /Chrome-nickel-molybdenum steel (EN 12756 - �Q1VGG)
SIC / Carbon / Viton (FPM) / Teflon (PTFE) sheated /Chrome-nickel-molybdenum steel (EN 12756 - Q1�M1GG)
036 WasherChrome steel(X20Cr13 / 1.4021) EN 10088 - 3
Chrome-nickel-molybdenum steel(X6CrNiMoTi 17-12-2 / 1.4571) EN 10088 - 3
037 Set screwChrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 2
047 ImpellerCast aluminium bronze(G-CuAl10Fe5Ni5 / CC33G-GS) EN 1982
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
048Tolerance ring for impeller
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
Chrome-nickel steel(X12CrNi 17-7 / 1.4310) EN 10088 - 2
049 Port plateGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
050 Valve plate Teflon (PTFE) Teflon (PTFE)
051 Intercepting plateChrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
Chrome-nickel-molybdenum steel(X10CrNiMoTi 18-10 / 1.4571) EN 10088 - 2
058 Gasket for cover Nitrile-butadiene-caotchouc (N�R 70) ISO 1629 Silicone core, Teflon (PTFE) sheated
061 CoverGrey cast iron(EN-GJL H� 195 / EN-JL2030) EN 1561
Cast chrome-nickel-molybdenum steel(G-X5CrNiMoNb 18-10 / 1.4581) EN 10283
063 Screw Steel (DIN ISO 8992) Steel (DIN ISO 8992)
068 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
069 Sealing ring Teflon (PTFE) Teflon (PTFE)
071Pipe of cavitation protection
Teflon (PTFE) Teflon (PTFE)
072Washer for cavita-tion protection
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
Chrome-nickel steel(X5CrNi 18-10 / 1.4301) EN 10088 - 3
079 Plug screwMachining steel, lead alloyed(11SMnPb30 / 1.0718) EN 10087
Chrome-nickel-molybdenum steel(X5CrNiMo 17-12-2 / 1.4401) EN 10088 - 3
080 Sealing ring Teflon (PTFE) Teflon (PTFE)
© Gardner Denver Deutschland GmbH 3 Techn. data sheet 2�V5 161, edition 06/2005 EnTechn. data sheet 2�V5 161, edition 06/2005 En
Gardner Denver Schopfheim GmbH Gardner Denver Deutschland GmbH
Elmo Rietschle is a brand of theGardner Denver Blower Division
Roggenbachstraße 5879650 Schopfheim - Germany
Industriestraße 2697616 �ad Neustadt - Germany
Tel.: +49 7622 392-0Fax: +49 7622 392-300
Tel.: +49 9771 6888-0Fax: +49 9771 6888-4000
Changes in particular the quoted performance curve, datas and weights without prior notice. The figures are without obligations.