Download - Storage Chest - learn.kregtool.com
![Page 1: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/1.jpg)
Storage Chest
Build a DIY storage chest using a single sheet of plywood and a 2×4! The perfect place to keep extra blankets, shoes, and
more.
Difficulty
Moderate
Page 1 of 10
![Page 2: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/2.jpg)
Page 2 of 10
![Page 3: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/3.jpg)
ToolsKreg Tools
Rip-Cut™
Kreg Pocket-Hole Jig® 720
Other Tools
Circular Saw (cordless)
Miter Saw
Tape Measure
Clamps
Drill (cordless)
Sander
MaterialsWood Products
Board , 2x4 , 96"1
Plywood , 1/2" Thick , Full Sheet1
Board , 2x2 , 96"1
Board , 1x2 , 96"1
Hardware & Supplies
Piano Hinges2
1 Inch Kreg Screws Pack1
Page 3 of 10
![Page 4: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/4.jpg)
Cut List & PartsLid , 48" X 16.5"1
Box Front/Back , 45" X 18"2
Box Sides , 18" X 15"2
Box Bottom , 44" X 15"1
Base Sides , 18" X 2" X 4"2
Base Front/Back , 48" X 2" X 4"2
Trim Front , 48" X 1" X 2"1
Trim Sides , 16" X 2" X 2"2
Page 4 of 10
![Page 5: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/5.jpg)
DirectionsStep 1:Cut 2x4's to build the base. Two are 48 inches and 2 are 18 inches (mitered in the corners). Assemble with pocket holes on
the bottom.
1
Page 5 of 10
![Page 6: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/6.jpg)
Step 2:Build the box for your storage chest. The front and back are 45" wide x 18" tall and the sides are 15" deep x 18" tall. Add
pocket holes on the sides with the Kreg Jig.
2
Page 6 of 10
![Page 7: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/7.jpg)
Step 6:The lid is 48" x 16.5" with piano hinges on the back. It's attached on the top of the box.3
Page 7 of 10
![Page 8: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/8.jpg)
Step 5The trim is added around the top of the box, right under the lid. The trim pieces are only on the front and sides. The front
piece is 48" x .75" and covers the front of the box and overhangs on either side. The side pieces are 16" x 1.5" and go along the
sides. These are attached with wood glue and no screw holes needed.
4
Page 8 of 10
![Page 9: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/9.jpg)
Step 3:To assemble the box, screw the side pieces into the front and back pieces. The sides connect into the front and back. (The
front goes all the way across - you can't see the ends of the side pieces.)
5
Page 9 of 10
![Page 10: Storage Chest - learn.kregtool.com](https://reader031.vdocument.in/reader031/viewer/2022012505/617fe8f3dbdf6942a960424e/html5/thumbnails/10.jpg)
Step 4:The bottom of the box is 44" x 15" and is attached inside with pocket holes. The front of the box covers the sides of the
bottom piece. To assemble, drop the bottom inside the box and attach with the pocket hole screws into the sides and back
of the box. Attach to the base with a nail gun or screws.
6
Page 10 of 10