Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.
Typical Details:Two Piece Molding System
©2
00
3 C
itad
el
Arc
hite
ctu
ral
Pro
du
cts,
In
c.
An
IS
O 9
00
1:2
00
0 R
eg
iste
red
Co
mpa
ny.
Pro
Co
re™
is
a r
eg
iste
red
tra
de
ma
rk o
f C
itad
el
Arc
hite
ctu
ral
Pro
du
cts,
In
c.P
rinte
d In
The
U.S
.A.
For
m #
7.0
3.T
D2.
B
Rev
. (1
1/06
) S
uper
sede
s (0
6/03
)
4
14
11
12
18
15
GENERAL DETAILS
1A - B: SYSTEM ISOMETRIC
2A - C: MOLDING DIMENSIONS
SECTION DETAILS
3A - C: BASE / FOUNDATION
4A - C: HORIZONTAL / VERTICAL
5: INTERMEDIATE CONNECTION
6A - C: DISSIMILAR MATERIAL
7: PARAPET
8A - B: INSIDE CORNER
9A - B: OUTSIDE CORNER
10: CURVED SECTION
INTERSECTION DETAILS
11A - B: BASE INSIDE CORNER
12A - B: BASE OUTSIDE CORNER
13A - D: HORIZONTAL / VERTICAL
14A - C: HORZ / VERT TERMINATION
15: HORZ TERMINATION ONLY
16A - C: INSIDE CORNER
17: THREE WAY INSIDE CORNER
18A - C: OUTSIDE CORNER
19A - B: DISSIMILAR MATERIAL CORNER
89
5
7
6
16
13
17
3
10
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 1A System Isometric Option 1.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
PROCORE™
TWO PIECE EXTRUDED
MOLDINGS
CONCEALED
FASTENERS
(BY OTHERS)
WORKING POINT
IS FACE OF
SUBSTRATE
NOTE:
PANEL IS REQUIRED
TO BE EMBEDDED
IN APPROVED SEALANT
(BY OTHERS - NOT SHOWN)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS.
NAILABLE SUBSTRATE
(BY OTHERS)
SYSTEM ISOMETRIC, OPTION 11A
PVC RECEIVERS
REINFORCING RODS
(NOT SHOWN)
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 1B System Isometric Option 2.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
PROCORE™
TWO PIECE (REVEAL)
EXTRUDED MOLDINGS
CONCEALED
FASTENERS
(BY OTHERS)
NOTE:
PANEL IS REQUIRED
TO BE EMBEDDED
IN APPROVED SEALANT
(BY OTHERS - NOT SHOWN)
NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS.
WORKING POINT
IS FACE OF
SUBSTRATE
SYSTEM ISOMETRIC, OPTION 21B
PVC RECEIVER
REINFORCING RODS
(NOT SHOWN)
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 2A Molding Dimensions Page 1.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
1 1/2"
(38mm)
1"
(25mm)
3/8"
(10mm)
3/4"
(19mm)
1 1/4"
(32mm)
ST-601MX
HORZ / VERT
R20-401
PVC RECEIVER
ST-603MX
PERIMETER J
R20-403
PVC RECEIVER
ST-605MX
INSIDE CORNER
R20-404
PVC RECEIVER
ST-607MX
OUTSIDE CORNER
R20-405
PVC RECEIVER
MOLDING DIMENSIONS, PAGE 12A
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 2B Molding Dimensions Page 2.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
2"
(51mm)
3/8"
(10mm)
1 1/4"
(32mm)
1"
(25mm)
1 1/2"
(38mm)
ST-201MX
HORZ / VERT
(EXTENDED FACE)
R20-401
PVC RECEIVER
ST-203MX
PERIMETER J
(EXTENDED FACE)
R20-403
PVC RECEIVER
ST-205MX
INSIDE CORNER
(EXTENDED FACE)
R20-404
PVC RECEIVER
ST-207MX
OUTSIDE CORNER
(EXTENDED FACE)
R20-405
PVC RECEIVER
MOLDING DIMENSIONS, PAGE 22B
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 2C Molding Dimensions Page 3.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
1/2"
(13mm)
1/2"
(13mm)
2"
(51mm) 1 1/2"
(38mm)
SR-701MX
HORZ / VERT
R20-406
PVC RECEIVER
SR-703MX
PERIMETER J
R20-407
PVC RECEIVER
MOLDING DIMENSIONS, PAGE 32C
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 3A Base Foundation Option 1.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
REINFORCING
ROD
ST-603MX
PERIMETER J
APPROVED SEALANT
(BY OTHERS)
ALUMINUM FLASHING
(BY OTHERS)
R20-403
PVC RECEIVER
FASTENER
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS
NAILABLE SUBSTRATE
(BY OTHERS)
BASE / FOUNDATION, OPTION 13A
BOND BREAKER
TAPE
(BY OTHERS)
FOUNDATION
(BY OTHERS)
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 3B Base Foundation Option 2.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
REINFORCING
ROD
ST-203MX
PERIMETER J
APPROVED SEALANT
(BY OTHERS)
ALUMINUM FLASHING
(BY OTHERS)
R20-403
PVC RECEIVER
FASTENER
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS
NAILABLE SUBSTRATE
(BY OTHERS)
BASE / FOUNDATION, OPTION 23B
BOND BREAKER
TAPE
(BY OTHERS)
FOUNDATION
(BY OTHERS)
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 3C Base Foundation Option 3.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
SR-703MX
PERIMETER J
APPROVED
SEALANT
(BY OTHERS)
ALUMINUM FLASHING
(BY OTHERS)
FOUNDATION
(BY OTHERS)
R20-407
PVC RECEIVER
FASTENER
(BY OTHERS)
NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY
AT STUD FRAMEWORK
LOCATIONS
BASE / FOUNDATION, OPTION 33C
BOND BREAKER TAPE
(BY OTHERS)
REINFORCING
ROD
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 4A Horizontal Vertical Option 1.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
ST-601MX
HORZ / VERT
APPROVED SEALANT
(BY OTHERS)
REINFORCING
ROD
FASTENER
(BY OTHERS)
NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS
HORIZONTAL / VERTICAL, OPTION 14A
R20-401
PVC RECEIVER
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 4B Horizontal Vertical Option 2.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
ST-201MX
HORZ / VERT
APPROVED SEALANT
(BY OTHERS)
REINFORCING
ROD
FASTENER
(BY OTHERS)
NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS
HORIZONTAL / VERTICAL, OPTION 24B
R20-401
PVC RECEIVER
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 4C Horizontal Vertical Option 3.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PANEL 15®
SR-701MX
HORZ / VERT
APPROVED
SEALANT
(BY OTHERS)
R20-406
PVC RECEIVER
FASTENER
(BY OTHERS)
NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS.
HORIZONTAL / VERTICAL, OPTION 34C
REINFORCING
ROD
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 5 Intermediate Connection.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
APPROVED
CONSTRUCTION
ADHESIVE
(BY OTHERS)
NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE SUBSTRATES,
FASTENERS MUST BE USED ONLY
AT STUD FRAMEWORK LOCATIONS.
NOTE:
IF MOISTURE BARRIER IS PRESENT,
SPECIAL INSTRUCTIONS APPLY,
REFER TO INSTALLATION GUIDELINES.
INTERMEDIATE CONNECTION5
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 6A Dissimilar Material Option 1.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
REINFORCING
ROD
FASTENER
(BY OTHERS)R20-403
PVC RECEIVER
NAILABLE SUBSTRATE
(BY OTHERS)NOTE:
FOR NON-NAILABLE SUBSTRATES,
FASTENERS MUST BE USED ONLY
AT STUD FRAMEWORK LOCATIONS
DISSIMILAR MATERIAL, OPTION 16A
DISSIMILAR
MATERIAL
(BY OTHERS)
BOND BREAKER
TAPE
(BY OTHERS)
APPROVED
SEALANT
(BY OTHERS) VARIES
(3/8" TO 1/2")
ST-603MX
PERIMETER J
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 6B Dissimilar Material Option 2.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
REINFORCING
ROD
ST-203MX
PERIMETER J
FASTENER
(BY OTHERS)R20-403
PVC RECEIVER
NAILABLE SUBSTRATE
(BY OTHERS)NOTE:
FOR NON-NAILABLE SUBSTRATES,
FASTENERS MUST BE USED ONLY
AT STUD FRAMEWORK LOCATIONS
DISSIMILAR MATERIAL, OPTION 26B
DISSIMILAR
MATERIAL
(BY OTHERS)
BOND BREAKER
TAPE
(BY OTHERS)
APPROVED
SEALANT
(BY OTHERS) VARIES
(3/8" TO 1/2")
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 6C Dissimilar Material Option 3.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
R20-407
PVC RECEIVER
FASTENER
(BY OTHERS)NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE SUBSTRATES,
FASTENERS MUST BE USED ONLY
AT STUD FRAMEWORK LOCATIONS
SR-703MX
PERIMETER J
PROCORE™
DISSIMILAR MATERIAL, OPTION 36C
DISSIMILAR
MATERIAL
(BY OTHERS)
BOND BREAKER
TAPE
(BY OTHERS)
VARIES
(3/8" TO 1/2")
APPROVED
SEALANT
(BY OTHERS)
REINFORCING
ROD
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 7 Parapet.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
BLOCKING
(BY OTHERS)
ALUMINUM
FLASHING
(BY OTHERS)
APPROVED SEALANT
(BY OTHERS)
PROCORE™
NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS
FASTENER
(BY OTHERS)
REINFORCING
ROD
PARAPET7
SHIM AS NEEDED
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 8A Inside Corner Option 1.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
PROCORE™
REINFORCING
ROD
APPROVED SEALANT
(BY OTHERS)
ST-205MX
I/S CORNER
R20-404
PVC RECEIVER
FASTENER
(BY OTHERS)
NAILABLE SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS
INSIDE CORNER, OPTION 18A
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 8B Inside Corner Option 2.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
INSIDE CORNER, OPTION 28B
NAILABLE
SUBSTRATE
(BY OTHERS)
FIELD ROUTED
AND BENT
APPROVED CONSTRUCTION
ADHESIVE (BY OTHERS) MAY
BE REQUIRED DEPENDING
UPON PANEL SPAN
(REFER TO INSTALLATION
INSTRUCTIONS)
PROCORE™
FACE SKIN MUST
BE .024" (MIN) ALUMINUM
TO UTILIZE THIS OPTION
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 9A Outside Corner Option1.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
ST-207MX
O/S CORNER
FASTENER
(BY OTHERS)
REINFORCING
ROD
PROCORE™
R20-405
PVC RECEIVER
NAILABLE
SUBSTRATE
(BY OTHERS)
NOTE:
FOR NON-NAILABLE
SUBSTRATES, FASTENERS
MUST BE USED ONLY AT
STUD FRAMEWORK
LOCATIONS
APPROVED SEALANT
(BY OTHERS)
OUTSIDE CORNER, OPTION 19A
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC 9B Outside Corner Option 2.dwg
SYSTEM:Two Piece Moldings
SCALE:1:1
FACE SKIN MUST
BE .024" (MIN) ALUMINUM
TO UTILIZE THIS OPTION
FIELD ROUTED
AND BENT
PROCORE™APPROVED CONSTRUCTION
ADHESIVE (BY OTHERS) MAY
BE REQUIRED DEPENDING
UPON PANEL SPAN
(REFER TO INSTALLATION
INSTRUCTIONS)
NAILABLE
SUBSTRATE
(BY OTHERS)
OUTSIDE CORNER, OPTION 29B
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC 10 Curved Section.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
CURVED SECTION10
PARAMETERS FOR FIELD CURVING PROCORE™ PANELS*:
BACKER MATERIAL**:
STANDARD .024" SMOOTH ALUMINUM
.030" SMOOTH FIBERGLASS REINFORCED PLASTIC (FRP)
.008" FIBERGLASS REINFORCED KRAFT/FOIL SCRIM
* ALL MOLDINGS MUST BE FACTORY CURVED. HOWEVER, FACTORY
CURVING NOT RECOMMENDED FOR PROCORE™ PANELS.
** FACE MATERIAL MUST BE .024" (MIN) ALUMINUM.
NOTE:
FOR SPECIFIC PROJECT REQUIREMENTS, CONTACT CITADEL.
MINIMUM RADIUS:
50 FT
8 FT
2 FT
BACK SKIN
FACE SKINPROCORE™
NOTE:
FOR COLUMN COVERS,
PLEASE REFER TO THE
ENVELOPE 2000® RR SYSTEM.
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC Intersections 11A To 12B.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
R20-404
PVC RECEIVER
R20-403
PVC RECEIVER
SR-703MX
EXTRUSION
MITERED AT 45°
ST-607MX
OR ST-207
O/S CORNER
R20-405
PVC RECEIVER
ST-603MX OR
ST-203MX
PERIMETER J
R20-405
PVC RECEIVER
R20-406
PVC RECEIVER
ST-605MX
OR ST-205MX
I/S CORNER
R20-404
PVC RECEIVER
ST-603MX OR
ST-203MX
PERIMETER J
BASE INSIDE CORNER, OPTION 111A BASE INSIDE CORNER, OPTION 211B
BASE OUTSIDE CORNER, OPTION 112A BASE OUTSIDE CORNER, OPTION 212B
MITERED AT 45°MITERED AT 45°
MITERED AT 45°
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC Intersections 13A To 13D.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
MITERED AT 45°
ST-601MX OR
ST-201MX
HORZ / VERT
R20-401
PVC RECEIVER
HORIZONTAL / VERTICAL, OPTION 113A HORIZONTAL / VERTICAL, OPTION 213B
GAP TO BE FILLED
WITH APPROVED SEALANT
(BY OTHERS)
MITERED
AT 45°
HORIZONTAL / VERTICAL, OPTION 313C HORIZONTAL / VERTICAL, OPTION 413D
SR-701MX
HORZ / VERT
R20-406
PVC RECEIVER
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC Intersections 14A To 15.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
MITERED
AT 45°
GAP TO BE FILLED
WITH APPROVED SEALANT
(BY OTHERS)
R20-407
PVC RECEIVER
SR-703MX
PERIMETER J
MITERED AT 45°
R20-401
PVC RECEIVER
R20-403
PVC RECEIVER
ST-603MX OR ST-203MX
PERIMETER J
ST-601MX
OR ST-201MX
HORZ / VERT
HORZ / VERT TERMINATION, OPTION 114A HORZ / VERT TERMINATION, OPTION 214B
HORZ / VERT TERMINATION, OPTION 314C HORIZONTAL TERMINATION ONLY15
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC Intersections 16A To 17.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
R20-404
PVC RECEIVER
ST-205MX OR
ST-605MX
I/S CORNER R20-406
PVC RECEIVER
SR-701MX
HORZ / VERT
ST-605MX
OR ST-205MX
I/S CORNER
ST-601MX OR
ST-201MX
HORZ / VERT
ALL THREE
MOLDINGS
TO BE MITERED
AT 45° ON
EACH LEG
ST-205MX OR
ST-605MX
I/S CORNER
R20-404
PVC RECEIVER
INSIDE CORNER, OPTION 116A INSIDE CORNER, OPTION 216B
INSIDE CORNER, OPTION 316C THREE WAY INSIDE CORNER17
GAP TO BE FILLED
WITH APPROVED SEALANT
(BY OTHERS)
MITERED
AT 45°
Citadel Architectural Products, Inc. ProCore™
Call (800) 446-8828 or visit www.citadelap.com TYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details. REVISED:
11/06
DRAWING NAME:PRO 2PC Intersections 18A To 18C.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
GAP TO BE
FILLED WITH
APPROVED
SEALANT
(BY OTHERS)
R20-405
PVC RECEIVER
ST-607MX OR
ST-207MX
O/S CORNER
R20-401
PVC RECEIVER
ST-607MX
OR ST-207MX
O/S CORNER
OUTSIDE CORNER, OPTION 118A OUTSIDE CORNER, OPTION 218B
OUTSIDE CORNER, OPTION 318C
MITERED AT 45°
Citadel Architectural Products, Inc.ProCore™
Call (800) 446-8828 or visit www.citadelap.comTYPICAL DETAILS
Note: This detail represents the latest recommendations from CitadelArchitectural Products, Inc. It is presented in good faith and is subject tochange without notice. Citadel Architectural Products, Inc. accepts noresponsibility for the end use of this detail. For conditions not shown,consult our Technical Staff at (800) 446-8828 for review of specific details.REVISED:
11/06
DRAWING NAME:PRO 2PC Intersections 19A To 19B.dwg
SYSTEM:Two Piece Moldings
SCALE:n/a
DISSIMILAR
MATERIAL
R20-403
PVC RECEIVER
MITERED AT 45°
ST-601MX OR
ST-201MX
HORZ / VERT
DISSIMILAR MATERIAL CORNER, OPT. 119A DISSIMILAR MATERIAL CORNER, OPT. 2
R20-406
PVC RECEIVER
19B
MITERED
AT 45°
BACKER ROD (IF
NECESSARY) AND
APPROVED SEALANT
(BY OTHERS)
SR-701MX
HORZ / VERT
DISSIMILAR
MATERIAL