-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
1/10
Use and operation of Caterpillar 854G Wheel Dozers
The intent of this document is layout the operational methods and procedure to bestoperate a Caterpillar wheel dozer.
Specifically to explain the use and operation of:
1. C!C
". !hrottle #oc$
%. &CS
4. #eft 'edal
5. &i(ht 'edal
). Ser*ice +ra$es
,. General operational tips
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
2/10
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
3/10
solenoid ased on the direction shift switch and speed sensors. Thepedal does not have to e used to achieve this smoother directionalshift.
!hrottle #oc$
The throttle lock is there to maintain engine R,- to give positiveresponse on rimpull and hydraulics especially in the lade loadingsegment of the $/ cycle. The throttle lock allows the engine to runat continuous R,- in order to provide ma"imum hydraulic power from
the implement pump.If the throttle lock is used when travelling it acts like the cruise controlon a car. It can e deactivated y application of the right pedal rakeor the panel3mounted switch shown aove.
4ote5 The throttle lock must e enaled efore engine speed can eset. 6n indicator light comes on when the throttle lock is enaled.
7sing the left pedal will not disconnect the throttle lock and if usedcan allow the machine to accelerate due to its weight ecause theretardation of the engine has een reduced from 100%. It is not recommended to use throttle lock and left pedal other thanwhen do+ing or when maneuvering at very low speed as the machine
!hrottle
#oc$
na+le
!hrottle
#oc$ Set
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
4/10
will drive through its rakes once the 20% Rimpull position on thepedal is reached.
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
5/10
#eft 'edal -C!C &i(ht 'edal -Ser*ice 2ra$e
The left pedal should be considered to function as a clutch where the powertrain is progressively disengaged from a ma"imum of100% rimpull to a minimum of 20% rimpull. This is used to control tyre slip and redirect power to the hydraulics toincrease lade response. This pedal should e considered as a ground speed controller whiledo+ing or while maneuvering at low speed on level ground.
&i(ht 'edal Ser*ice 2ra$e#eft 'edal C!C
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
6/10
The left pedal should never be used to brake the machine. Therake application at the end of clutch pedal travel allows the operatorto hold the machine in position without having to use the right rakepedal which would re&uire using oth feet and would disengage
throttle lock. 7sing the left pedal while working ground speed shoulde low 1st gear and only 20% Rimpull is working against the rakes. The key thing to rememer is that the left pedal8s raking function is tocontrol the machine not to retard or stop the machine while intransport. ICTC helps to match ground speed with working conditions.
The dierence between left (clutch) and riht (brake) pedalactuation is that the left pedal reduces clutch pressure whichlimits the enine!s natural retardin capability, but can stillprovide 20% rimpull aainst the brakes.
"iht pedal is brake only, disenaes the throttle lock, andmaintains the enine!s natural retardin capability to helpslow the machine
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
7/10
&CS -&i/pull Control Syste/
"impull #ontrol $ystemThe Impeller Clutch Torque Converter (ICTC) pedal works very well by itself to controlground speed provide smoother directional shifts and for controlling occasional tire slip.
!owever certain dozing conditions such as coal applications or wet slick floors may
require a reduced rimpull setting for long periods in order to prevent costly tire slip."ather than the operator trying to find the best rimpull setting with the ICTC pedal the
operator can use the "impull Control #ystem ("C#) selector dial to select the ma$imum
desired rimpull from four factory preset positions%
3axi/u/ i(h 3ediu/ and #o6. &ffective with ('**+,-) all -/0 1heel
2ozers will have the "C# installed at the factory as standard equipment. To retrofit your
current ' serial number machine please see #&2 *345 for information.
1hen the "C# selection switch is in any position other than ma$imum an indicator light
on the dash will illuminate. The operator can choose the reduced setting that best matches
conditions. 'dditional rimpull modulation can still be achieved with the left pedal. 6ore$ample if the operator selects the edium setting he can then modulate from that point
down to ,* percent. "C# is active in first forward gear only. If the operator shifts to
second gear or higher the machine will provide 7** percent rimpull. 1hen he shifts back
to first gear the rimpull will revert back to the level selected.
ene&ts8 9ower tire costs due to better operator control of rimpull8 #moother shifts without having to lower engine rpm during directional changes
8 a$imum hydraulic efficiency : the operator can maintain high engine rpm by using
Throttle 9ock and still control wheel slip
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
8/10
8 ICTC provides smooth ground speed control allowing the operator to smoothly
approach and back away from ob;ects
8 ICTC
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
9/10
General 9perational !ips -Su//aryIt is recommended the $/ e operated with throttle lock activatedand on in #rst gear. This enales the redirection of full engine power
from Rimpull to hydraulics to match ground speed to hydraulicimplement speed. 7se of The ICTC is useful when loading lade or in areas where
rimpull control is desirale. 6n e"ample where ICTC is useful is wheretyre slip may occur or in poor underfoot or ony material.
The right pedal is the service rake and should e used for all
raking.7sing the right pedal natural engine retardation assists in the raking
process. Recommended for 2nd 9 :rd gear The throttle lock is disengaged when the right pedal is depressed.
The $/ is capale of maintaining constant speed in 2nd gear on a
ramp of 11% e!ective grade downhill using engine retardation alone.6ssumes second gear operation 6t an 11% grade with ;ock 7p Converter switched on throttle lock
o! no service raking should e re&uired.
-
8/18/2019 Use an Operation of Caterpillar 854G Wheel Dozers(Final)
10/10