Quick Reference 930502H © 2015, CyberData Corporation, ALL RIGHTS RESERVED© 2015, CyberData Corporation, ALL RIGHTS RESERVED 930502H Quick Reference
Wall Mounting Options
Gang Box Mounting Options
Backplate
Wall
(Not Provided)
Network Cable &
for Ground Wire ConnectionPick One of Four Mounting Hole
Screw121001A
Accessory Kit
(4 Places) on WallPre Drill Holes
Ground Wire
Cutout
MountingScrew (3x)
SlotEntryCable
ClosedSlotsCable
Two Gang Box use four
Wall Cutout
or Two Gang Box
Backplate acceptSingle Gang Box
Single Gang Box use two
Backplate
Wall Cutout
121002BScrew Accessory Kit
MountingScrew (3x)
(Not Provided)Ground Wire
Any Available Mounting HoleGround Wire Connect to
(Not Provided)Network Cable
SlotEntryCable
ClosedSlotsCable
Getting Started• Download the VoIP V3 Indoor Intercom Operations Guide PDF file from the following web page:
http://www.cyberdata.net/products/voip/digitalanalog/intercomindoorv3/docs.html
• Create a plan for the locations of your Intercoms.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: This enclosure is not rated for any AC voltages!
Parts
Contacting CyberData
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa 10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Maska 255.0.0.0
Default Gatewaya 10.0.0.1
a. Default if there is not a DHCP server present.
(4) Plastic Ribbed Anchor (4) #6-32 FlatHead Countersunk Machine Screw
(1) Wall Mounting Kit(1) Intercom Assembly (1) Gang Box Mounting Kit
(4) Sheet Metal Screw
Sales: (831) 373-2601 ext. 334Support: 831-373-2601 ext. 333Support Website: http://support.cyberdata.net/RMA Department: (831) 373-2601 ext. 136RMA Email: [email protected] Status: http://support.cyberdata.net/Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation3 Justin CourtMonterey, CA 93940, USA
Phone: 831-373-2601Fax: 831-373-4193http://www.cyberdata.net/
The IP Endpoint Company
Installation Quick Reference
VoIP V3 Indoor IntercomSIP Compliant011211*, RAL 9003, Signal White*Replaces the 011111 number.
© 2015, CyberData Corporation, ALL RIGHTS RESERVED 930502H Quick Reference Quick Reference 930502H © 2015, CyberData Corporation, ALL RIGHTS RESERVED
RTFM Button
Dimensions
Maximum Recommended Wall Cutout Dimensions
SW1
When the device is operational and linked to a network, you can use the Reset Test Function Management (RTFM) button (SW1 [see picture]) to announce the device’s IP address or restore the device to the factorydefault settings.
To announce the device’s current IP address:
• Press and release the RTFM button within a five second window.
Note The device will use DHCP to obtain the new IP address (DHCP-assigned address or default to 10.10.10.10 if a DHCP server is not present).
To restore the device to factory default settings:
• Press and hold the RTFM button for longer than five seconds until you hear the device announce that it is restoring the factory default settings.
4.53 [115.0]
4.53 [115.0]2.22 [56.3]DIMENSIONS ARE IN INCHES [MILLIMETER]
Dimensions are in Inches [Millimeter]
Wall Cutout
0.25 [6.4]
0.25 [6.4]
0.25 [6.4]
0.25 [6.4]Top Cable Entry Closed
Top Cable Entry Opening
Cable Connections
Terminal Block Connections
to J2
021078D
Speaker to J7
Back Plate
Push-Button
to J6Microphone
PCBA
MountingScrews
MountingScrews
PCBA
J7
J6
J2
Wire (IN)Terminal Blockcan accept16 AWG wire
J3 Terminal Block
16
Alternate Power Input:1 = +8 to +12VDC @ 1000mA Regulated Power Supply*2 = Power Ground*
Relay Contact:(1 A at 30 VDC for continuous loads)3 = Normally Open Common4 = Normally Open Contact5 = Door Sense Input6 = Door Sense Ground Reference
*Contacts 1 and 2 on the J3 terminal block are only for powering the device from a non-PoE 12VDC power source as an alternative to Network PoE power. Use of these contacts for any other purpose will damage the device and void the product warranty.
3 4