Download - Wrt54gl v11 Ug Nc
-
7/28/2019 Wrt54gl v11 Ug Nc
1/32
USER GUIDE
Wireless-G
Broadband Router
Model No: WRT54GL
-
7/28/2019 Wrt54gl v11 Ug Nc
2/32
Table of Contents
Wreless-G Broadband Router
About This Guide 1
Icon Descriptions 1
Online Resources 1
Copyright and Trademarks 1
Chapter 1: Product Overview 2Front Panel 2
Back Panel 2
Chapter 2: Wireless Security Checklist 3
General Network Security Guidelines 3
Additional Security Tips 3
Chapter 3: Advanced Confguration 4
Setup > Basic Setup 4
Setup > DDNS 7Setup > MAC Address Clone 8
Setup > Advanced Routing 9
Wireless > Basic Wireless Settings 9
Wireless > Wireless Security 10
Wireless > Wireless MAC Filter 12
Wireless > Advanced Wireless Settings 13
Security > Firewall 14
Security > VPN Passthrough 14
Access Restrictions > Internet Access 15
Applications and Gaming > Port Range Forward 16Applications & Gaming > Port Triggering 16
Applications and Gaming > DMZ 17
Applications and Gaming > QoS 17
Administration > Management 18
Administration > Log 19
Administration > Diagnostics 19
Administration > Factory Deaults 19
Administration > Firmware Upgrade 20
Administration > Confg Management 20
Status > Router 20Status > Local Network 21
Status > Wireless 21
Appendix A: Troubleshooting 22
Appendix B: Specifcations 23
Appendix C: Warranty and Regulatory Inormation 24
Limited Warranty 24
Wireless Disclaimer 25
-
7/28/2019 Wrt54gl v11 Ug Nc
3/32
Table of Contents
Wreless-G Broadband Router
FCC Statement 25
Saety Notices 25
Industry Canada (Canada) 25
IC Statement 25
Rglement dIndustry Canada 25
User Inormation or Consumer Products Covered by EU Directive 2002/96/EC on WasteElectric and Electronic Equipment (WEEE) 26
-
7/28/2019 Wrt54gl v11 Ug Nc
4/32
About This Guide
Wreless-G Broadband Router
About Ths Gude
Icon Descriptions
While reading through the User Guide you may encounter
various icons designed to call attention to a speciic itemBelow is a description o these icons:
NOTE: This check mark indicates that there isa note o interest and is something that youshould pay special attention to while using theproduct
WARNING: This exclamation point indicatesthat there is a caution or warning and it issomething that could damage your property orproduct
WEB: This globe icon indicates a noteworthywebsite address or e-mail address
Online Resources
Most web browsers allow you to enter the web addresswithout adding the http:// in ront o the address ThisUser Guide will reer to websites without including http://in ront o the address Some older web browsers may
require you to add it
Resource Webste
Linksys wwwlinksyscom
Linksys International wwwlinksyscom/international
Glossary wwwlinksyscom/glossary
Network Security wwwlinksyscom/security
Copyright and Trademarks
Speciications are subject to change without notice
Linksys is a registered trademark or trademark o CiscoSystems, Inc and/or its ailiates in the US and certainother countries Copyright 2007 Cisco Systems, Inc Allrights reserved Other brands and product names aretrademarks or registered trademarks o their respectiveholders
-
7/28/2019 Wrt54gl v11 Ug Nc
5/32
Chapter1 Product Overview
Wreless-G Broadband Router
Chapter :Product Overvew
Thank you or choosing the Linksys Wireless-G BroadbandRouter The Router lets you access the Internet via a
wireless connection, broadcast at up to 54 Mbps, orthrough one o its our switched ports You can also usethe Router to share resources such as computers, printersand iles A variety o security eatures help to protectyour data and your privacy while online Security eaturesinclude WPA2 security, a Stateul Packet Inspection (SPI)irewall and NAT technology Coniguring the Router iseasy using the provided browser-based utility
Front Panel
SecureEasySetup (Orange/White) The Ciscologo is the Routers SecureEasySetup button Itlights up and will stay orange when the Routeris powered on The color orange indicates thatthe Router is not using the SecureEasySetupeature, while the color white indicates that theRouter is using the SecureEasySetup eature
When the Router enters SecureEasySetupmode, the Cisco logo will turn white andstart lashing Ater the Router has generatedthe SSID and WPA Personal key, the Ciscologo will stop lashing and stay white
To clear the SSID and WPA Personal key, pressand hold down the Cisco logo or ive secondsThe Cisco logo will lash slowly as the Routerresets itsel The Cisco logo will turn orange toindicate a successul reset
NOTE:SecureEasySetup is a eature that makes
it easy to set up your wireless network I youhave SecureEasySetup devices, run the RoutersSetup Wizard CD-ROM and ollow the on-screen instructions to use SecureEasySetup
Power (Green) The Power LED lights upand will stay on while the Router is poweredon When the Router goes through its sel-diagnostic mode during every boot-up, thisLED will lash When the diagnostic is complete,the LED will be solidly lit
DMZ (Green) The DMZ LED indicates whenthe DMZ unction is being used This LED willremain lit as long as DMZ is enabled
WLAN (Green) The WLAN LED lights up whenthe wireless eature is enabled I the LED islashing, the Router is actively sending orreceiving data over the network
, , 3, 4 (Green) These numbered LEDs,corresponding with the numbered ports on theRouters back panel, serve two purposes I theLED is continuously lit, the Router is successullyconnected to a device through that port A
lashing LED indicates network activity overthat port
Internet (Green) The Internet LED lights upwhen there is a connection made through theInternet port A lashing LED indicates networkactivity over the Internet port
Back Panel
Reset There are two ways to reset the Routersactory deaults Either press and hold the ResetButton or approximately ive seconds, or restorethe deaults rom Administration > FactoryDeaults in the Routers web-based utility
InternetThe Internet port is where you will
connect your cable or DSL Internet connection
, , 3, 4 These Ethernet ports (1, 2, 3, 4) connectthe Router to PCs on your wired network andother Ethernet network devices
Power The Power port is where you willconnect the power adapter
-
7/28/2019 Wrt54gl v11 Ug Nc
6/32
Chapter2 Wireless Security Checklist
3Wreless-G Broadband Router
Chapter :Wreless Securty Checklst
Wireless networks are convenient and easy to install, sohomes with high-speed Internet access are adopting them
at a rapid pace Because wireless networking operates bysending inormation over radio waves, it can be morevulnerable to intruders than a traditional wired networkLike signals rom your cellular or cordless phones, signalsrom your wireless network can also be intercepted Sinceyou cannot physically prevent someone rom connectingto your wireless network, you need to take some additionalsteps to keep your network secure
. Change the default wrelessnetwork name or SSID
Wireless devices have a deault wireless network nameor Service Set Identiier (SSID) set by the actory Thisis the name o your wireless network, and can be upto 32 characters in length Linksys wireless productsuse lnksys as the deault wireless network name Youshould change the wireless network name to somethingunique to distinguish your wireless network rom otherwireless networks that may exist around you, but do notuse personal inormation (such as your Social Securitynumber) because this inormation may be available oranyone to see when browsing or wireless networks
. Change the default password
For wireless products such as access points and routers,you will be asked or a password when you want to changetheir settings These devices have a deault password setby the actory The Linksys deault password is admnHackers know these deaults and may try to use themto access your wireless device and change your networksettings To thwart any unauthorized changes, customizethe devices password so it will be hard to guess
3. Enable MAC address flterng
Linksys routers give you the ability to enable Media AccessControl (MAC) address iltering The MAC address is aunique series o numbers and letters assigned to everynetworking device With MAC address iltering enabled,wireless network access is provided solely or wirelessdevices with speciic MAC addresses For example, you canspeciy the MAC address o each computer in your homeso that only those computers can access your wirelessnetwork
4. Enable encrypton
Encryption protects data transmitted over a wirelessnetwork Wi-Fi Protected Access (WPA/WPA2) and WiredEquivalency Privacy (WEP) oer dierent levels o security
or wireless communication Currently, devices that areWi-Fi certiied are required to support WPA2, but are notrequired to support WEP
A network encrypted with WPA/WPA2 is more securethan a network encrypted with WEP, because WPA/WPA2uses dynamic key encryption To protect the inormationas it passes over the airwaves, you should enable thehighest level o encryption supported by your networkequipment
WEP is an older encryption standard and may be theonly option available on some older devices that do not
support WPA
General Network Security Guidelines
Wireless network security is useless i the underlyingnetwork is not secure
Password protect all computers on the network andindividually password protect sensitive iles
Change passwords on a regular basis
Install anti-virus sotware and personal irewallsotware
Disable ile sharing (peer-to-peer) Some applicationsmay open ile sharing without your consent and/orknowledge
Additional Security Tips
Keep wireless routers, access points, or gateways awayrom exterior walls and windows
Turn wireless routers, access points, or gatewayso when they are not being used (at night, duringvacations)
Use strong passphrases that are at least eight characters
in length Combine letters and numbers to avoid usingstandard words that can be ound in the dictionary
WEB: For more inormation on wirelesssecurity, visit www.lnksys.com/securty
-
7/28/2019 Wrt54gl v11 Ug Nc
7/32
Chapter3 Advanced Configuration
4Wreless-G Broadband Router
Chapter 3:Advanced Confguraton
Ater setting up the Router with the Setup Wizard (locatedon the CD-ROM), the Router will be ready or use However,
i youd like to change its advanced settings, use theRouters web-based utility This chapter describes eachweb page o the utility and each pages key unctions Youcan access the utility via a web browser on a computerconnected to the Router
The web-based utility has these main tabs: Setup,Wireless, Security, Access Restrictions, Applications &Gaming, Administration, and Status Additional tabs willbe available ater you click one o the main tabs
NOTE: When irst installing the Router, youshould use the Setup Wizard on the Setup
CD-ROM I you want to conigure advancedsettings, use this chapter to learn about theweb-based utility
How to Access the Web-Based Utility
To access the web-based utility, launch the web browser onyour computer, and enter the Routers deault IP address,9.68.., in theAddress ield Then, press Enter
A password request screen will appear (Non-Windows XPusers will see a similar screen) Leave the User name ield
blank The irst time you open the Web-based utility, usethe deault password admn (You can set a new passwordrom the Administration tabs Management screen) ClickOK to continue
Password Screen
Setup > Basic Setup
The irst screen that appears is the Basic Setup screen Thisallows you to change the Routers general settings
Setup > Basic Setup
Internet Setup
The Internet Setup section conigures the Router to yourInternet connection Most o this inormation can beobtained through your ISP
Internet Connection Type
Select the type o Internet connection your ISP providesrom the drop-down menu The available types are:
Automatic Coniguration - DHCP
Static IP
PPPoE
PPTP
L2TP
Telstra Cable
Automatic Configuration - DHCP
By deault, the Routers Internet Connection Type is set
to Automatc Confguraton - DHCP, which should bekept only i your ISP supports DHCP or you are connectingthrough a dynamic IP address (This option usually appliesto cable connections)
Internet Connection Type > Automatic Coniguration - DHCP
-
7/28/2019 Wrt54gl v11 Ug Nc
8/32
Chapter3 Advanced Configuration
Wreless-G Broadband Router
Static IP
I you are required to use a permanent IP address toconnect to the Internet, select Statc IP
Internet Connection Type > Static IP
Internet IP Address This is the Routers IP address, whenseen rom the Internet Your ISP will provide you with theIP Address you need to speciy here
Subnet Mask This is the Routers Subnet Mask, as seenby users on the Internet (including your ISP) Your ISP willprovide you with the Subnet Mask
Gateway Your ISP will provide you with the GatewayAddress, which is the ISP servers IP address
DNS Your ISP will provide you with at least one DNS(Domain Name System) Server IP Address
PPPoE
Some DSL-based ISPs use PPPoE (Point-to-Point Protocolover Ethernet) to establish Internet connections I you areconnected to the Internet through a DSL line, check withyour ISP to see i they use PPPoE I they do, you will have
to enable PPPoE
Internet Connection Type > PPPoE
User Name and Password Enter the User Name andPassword provided by your ISP
Servce Name I provided by your ISP, enter the ServiceName
Connect on Demand: Max Idle Tme You can conigurethe Router to cut the Internet connection ater it has beeninactive or a speciied period o time (Max Idle Time) Iyour Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as youattempt to access the Internet again To use this option,select Connect on Demand In the Max Idle Time ield,enter the number o minutes you want to have elapsed
beore your Internet connection terminates The deaultMax Idle Time is minutes
Keep Alve: Redal Perod I you select this option,the Router will periodically check your Internetconnection I you are disconnected, then the Routerwill automatically re-establish your connection To use
this option, select Keep Alve In the Redial Period ield,you speciy how oten you want the Router to checkthe Internet connection The deault Redial Period is30 seconds
PPTP
Point-to-Point Tunneling Protocol (PPTP) is a service thatapplies to connections in Europe only
Internet Connection Type > PPTP
Internet IP Address This is the Routers IP address, asseen rom the Internet Your ISP will provide you with theIP Address you need to speciy here
Subnet Mask This is the Routers Subnet Mask, as seenby users on the Internet (including your ISP) Your ISP will
provide you with the Subnet MaskGateway Your ISP will provide you with the GatewayAddress
User Name and Password Enter the User Name andPassword provided by your ISP
Connect on Demand: Max Idle Tme You can conigurethe Router to cut the Internet connection ater it has beeninactive or a speciied period o time (Max Idle Time) Iyour Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as you
attempt to access the Internet again To use this option,select Connect on Demand In the Max Idle Time ield,enter the number o minutes you want to have elapsedbeore your Internet connection terminates The deaultMax Idle Time is minutes
Keep Alve: Redal Perod If you select this option, theRouter will periodically check your Internet connection If
you are disconnected, then the Router will automatically
re-establish your connection To use this option, selectKeep Alve In the Redial Periodfield, you specify how often
you want the Router to check the Internet connection The
default value is 30 seconds
-
7/28/2019 Wrt54gl v11 Ug Nc
9/32
Chapter3 Advanced Configuration
6Wreless-G Broadband Router
L2TP
L2TP is a service that applies to connections in Israel only
Internet Connection Type > L2TP
User Name and Password Enter the User Name andPassword provided by your ISP
LTP Server This is the IP address o the L2TP ServerYour ISP will provide you with the IP Address you need tospeciy here
Connect on Demand: Max Idle Tme You can conigure
the Router to cut the Internet connection ater it has beeninactive or a speciied period o time (Max Idle Time) Iyour Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as youattempt to access the Internet again To use this option,select Connect on Demand In the Max Idle Time ield,enter the number o minutes you want to have elapsedbeore your Internet connection terminates The deaultMax Idle Time is minutes
Keep Alve: Redal Perod I you select this option,the Router will periodically check your Internetconnection I you are disconnected, then the Routerwill automatically re-establish your connection To usethis option, select Keep Alve In the Redial Period ield,you speciy how oten you want the Router to checkthe Internet connection The deault Redial Period is30 seconds
Telstra Cable
Telstra Cable is a service that applies to connections inAustralia only
Internet Connection Type > Telstra Cable
User Name and Password Enter the User Name andPassword provided by your ISP
Heart Beat Server This is the IP address o the HeartbeatServer Your ISP will provide you with the IP Address youneed to speciy here
Connect on Demand: Max Idle Tme You can conigurethe Router to cut the Internet connection ater it has beeninactive or a speciied period o time (Max Idle Time) Iyour Internet connection has been terminated due toinactivity, Connect on Demand enables the Router toautomatically re-establish your connection as soon as you
attempt to access the Internet again To use this option,select Connect on Demand In the Max Idle Time ield,enter the number o minutes you want to have elapsedbeore your Internet connection terminates The deaultMax Idle Time is minutes
Keep Alve: Redal Perod I you select this option,the Router will periodically check your Internetconnection I you are disconnected, then the Routerwill automatically re-establish your connection To usethis option, select Keep Alve In the Redial Period ield,you speciy how oten you want the Router to checkthe Internet connection The deault Redial Period is30 seconds
Optional Settings
Some o these settings may be required by your ISP Veriywith your ISP beore making any changes
Optional Settings
Router Name In this ield, you can enter a name o up to39 characters to represent the Router
Host Name/Doman Name These ields allow you tosupply a host and domain name or the Router Some ISPs,usually cable ISPs, require these names as identiicationYou may have to check with your ISP to see i yourbroadband Internet service has been conigured with ahost and domain name In most cases, leaving these ieldsblank will work
MTU MTU is the Maximum Transmission Unit It speciiesthe largest packet size permitted or Internet transmission
Select Manual i you want to manually enter the largestpacket size that is transmitted To have the Router selectthe best MTU or your Internet connection, keep thedeault setting, Auto
Sze When Manual is selected in the MTUield, this optionis enabled Leave this value in the 1200 to 1500 range Thedeault size depends on the Internet Connection Type:
DHCP, Static IP, or Telstra: 00
PPPoE: 49
PPTP or L2TP: 460
-
7/28/2019 Wrt54gl v11 Ug Nc
10/32
Chapter3 Advanced Configuration
Wreless-G Broadband Router
Network Setup
The Network Setup section changes the settings on thenetwork connected to the Routers Ethernet ports WirelessSetup is perormed through the Wireless tab
Router IP
This presents both the Routers IP Address and SubnetMask as seen by your network
Router IP Address
Network Address Server Settings (DHCP)
The settings allow you to conigure the Routers DynamicHost Coniguration Protocol (DHCP) server unction The
Router can be used as a DHCP server or your network ADHCP server automatically assigns an IP address to eachcomputer on your network I you choose to enable theRouters DHCP server option, make sure there is no otherDHCP server on your network
Network Address Server Settings (DHCP)
DHCP Server DHCP is enabled by actory deault I youalready have a DHCP server on your network, or you dontwant a DHCP server, then select Dsable (no other DHCPeatures will be available)
Startng IP Address Enter a value or the DHCP server tostart with when issuing IP addresses Because the Routersdefault IP address is 19216811, the Starting IP Address must
be 19216812 or greater, but smaller than 1921681253
The default Starting IP Address is 9.68..00
Maxmum Number of DHCP Users Enter the maximumnumber o PCs that you want the DHCP server to assignIP addresses to This number cannot be greater than 253The deault is 0
Clent Lease Tme The Client Lease Time is the amounto time a network user will be allowed connection to theRouter with their current dynamic IP address Enter theamount o time, in minutes, that the user will be leasedthis dynamic IP address Ater the time is up, the user willbe automatically assigned a new dynamic IP address Thedeault is 0 minutes, which means one day
Statc DNS (-3) The Domain Name System (DNS) is howthe Internet translates domain or website names into
Internet addresses or URLs Your ISP will provide you with at
least one DNS Server IP Address If you wish to use another,
enter that IP Address in one of these fields You can enter up
to three DNS Server IP Addresses here The Router will use
these for quicker access to functioning DNS serversWINS The Windows Internet Naming Service (WINS)manages each PCs interaction with the Internet I youuse a WINS server, enter that servers IP Address hereOtherwise, leave this blank
Time Setting
Select the time zone in which your network unctionsrom this drop-down menu (You can even automaticallyadjust or daylight saving time)
Time Setting
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Setup > DDNS
The Router oers a Dynamic Domain Name System (DDNS)eature DDNS lets you assign a ixed host and domainname to a dynamic Internet IP address It is useul whenyou are hosting your own website, FTP server, or other
server behind the RouterBeore you can use this eature, you need to signup or DDNS service with a DDNS service provider,wwwdyndnsorg or wwwTZOcom I you do not want touse this eature, keep the deault setting, Dsable
DDNS
DDNS Service
I your DDNS service is provided by DynDNSorg, thenselect DynDNS.org rom the drop-down menu I yourDDNS service is provided by TZO, then select TZO.com
The eatures available on the DDNS screen will vary,depending on which DDNS service provider you use
-
7/28/2019 Wrt54gl v11 Ug Nc
11/32
Chapter3 Advanced Configuration
8Wreless-G Broadband Router
DynDNS.org
Setup > DDNS > DynDNS
System Select the DynDNS service you use: Dynamc,
Statc, or Custom The deault selection is DynamcUser Name Enter the User Name or your DDNS account
Password Enter the Password or your DDNS account
Host Name The is the DDNS URL assigned by the DDNSservice
Mal Exchange (Optonal) Enter the address o your mailexchange server, so e-mails to your DynDNS address go toyour mail server
Backup MX This eature allows the mail exchange serverto be a backup To disable this eature, keep the deault,No To enable the eature, select Yes I you are not sure
which setting to select, keep the deault, No
WldCard This setting enables or disables wildcardsor your host For example, i your DDNS address ismyplace.dyndns.org and you enable wildcards, thenx.myplace.dyndns.org will work as well (x is the wildcard)To disable wildcards, keep the deault, Off To enablewildcards, select On I you are not sure which setting toselect, keep the deault, Off
Internet IP Address The Routers Internet IP address isdisplayed here Because it is dynamic, it will change
Status The status o the DDNS service connection is
displayed hereClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
TZO.com
Setup > DDNS > TZO
E-mal Address, Password, and Doman Name Enterthe settings o the account you set up with TZO
Internet IP Address The Routers Internet IP address is
displayed here Because it is dynamic, it will changeStatus The status o the DDNS service connection isdisplayed here
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Setup > MAC Address Clone
A MAC address is a 12-digit code assigned to a uniquepiece o hardware or identiication Some ISPs will requireyou to register a MAC address in order to access theInternet I you do not wish to re-register the MAC address
with your ISP, you may assign the MAC address you havecurrently registered with your ISP to the Router with theMAC Address Clone eature
Setup > MAC Address Clone
MAC Address Clone
Enable/Dsable To have the MAC Address cloned, selectEnable
User Defned Entry Enter the MAC Address registeredwith your ISP here
Clone Your PCs MAC Clicking this button will clone theMAC address o the computer you are using
-
7/28/2019 Wrt54gl v11 Ug Nc
12/32
Chapter3 Advanced Configuration
9Wreless-G Broadband Router
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Setup > Advanced Routing
This screen is used to set up the Routers advancedunctions Operating Mode allows you to select thetype(s) o advanced unctions you use Dynamic Routingautomatically adjusts how packets travel on your networkStatic Routing sets up a ixed route to another networkdestination
Setup > Advanced Routing (Gateway)
Setup > Advanced Routing (Router)
Advanced Routing
Operatng Mode Select the mode in which this Routerwill unction I this Router is hosting your networksconnection to the Internet, select Gateway I anotherRouter exists on your network, select Router WhenRouter is chosen, Dynamc Routng will be available asan option
Dynamic Routing
RIP This eature enables the Router to automaticallyadjust to physical changes in the networks layout and
exchange routing tables with the other router(s) TheRouter determines the network packets route based onthe ewest number o hops between the source and thedestination This eature is Dsabled by deault From thedrop-down menu, you can also select LAN & Wreless,which perorms dynamic routing over your Ethernet and
wireless networks You can also select WAN (Internet),which perorms dynamic routing with data coming romthe Internet Selecting Both enables dynamic routing orboth networks, as well as data rom the Internet
Static Routing
Select set number To set up a static route betweenthe Router and another network, select a number romthe drop-down list (A static route is a pre-determinedpathway that network inormation must travel to reach aspeciic host or network) Enter the inormation describedbelow to set up a new static route (ClickDelete Ths Entryto delete a static route)
Enter Route Name Enter a name or the Route here,using a maximum o 25 alphanumeric characters
Destnaton LAN IP The Destination LAN IP is the addresso the remote network or host to which you want to assigna static route
Subnet Mask The Subnet Mask determines whichportion o a Destination LAN IP address is the networkportion, and which portion is the host portion
Default Gateway This is the IP address o the gatewaydevice that allows or contact between the Router and theremote network or host
Interface This interace tells you whether the DestinationIP Address is on the LAN & Wreless (Ethernet and wirelessnetworks) or the WAN(Internet)
ClickShow Routng Table to view the Static Routes youhave already set up
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Wireless > Basic Wireless Settings
The basic settings or wireless networking are set on this
screen
-
7/28/2019 Wrt54gl v11 Ug Nc
13/32
Chapter3 Advanced Configuration
0Wreless-G Broadband Router
Wireless > Basic Wireless Settings
Wireless Network
Wreless Network Mode From this drop-down menu,you can select the wireless standards running on yournetwork I you have both 80211g and 80211b devicesin your network, keep the deault setting, Mxed I youhave only 80211g devices, select G-Only I you haveonly 80211b devices, select B-Only I you do not haveany 80211g and 80211b devices in your network, selectDsable
Wreless Network Name (SSID) The SSID is the networkname shared among all points in a wireless networkThe SSID must be identical or all devices in the wirelessnetwork It is case-sensitive and must not exceed32 characters (use any o the characters on the keyboard)Make sure this setting is the same or all points in yourwireless network For added security, you should change
the deault SSID (lnksys) to a unique name
Wreless Channel Select the appropriate channel romthe list provided to correspond with your network settingsAll devices in your wireless network must use the samechannel in order to communicate
Wreless SSID Broadcast When wireless clients surveythe local area or wireless networks to associate with, theywill detect the SSID broadcast by the Router To broadcastthe Routers SSID, keep the deault setting, Enable I youdo not want to broadcast the Routers SSID, then selectDsable
SecureEasySetup I you did not utilize this networkconnection eature during the Setup Wizard, you may useit here by clicking the green logo When you are promptedto start the push button setup, clickOK
Reset Securty Use this button to reset the securitysettings on your network You will need to runSecureEasySetup again on each device on your networkto re-associate it with your network
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Wireless > Wireless Security
The Wireless Security settings conigure the security oyour wireless network There are six wireless securitymode options supported by the Router: WPA Personal,WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS,
and WEP (WPA stands or Wi-Fi Protected Access, whichis a security standard stronger than WEP encryption WEPstands or Wired Equivalent Privacy, while RADIUS standsor Remote Authentication Dial-In User Service) Thesesix are briely discussed here For detailed instructionson coniguring wireless security or the Router, reer toChapter 2: Wireless Security
Wireless Security
Security Mode
Select the security method or your wireless network Iyou do not want to use wireless security, keep the deault,Dsabled
WPA Personal
NOTE: I you are using WPA, always rememberthat each device in your wireless network MUSTuse the same WPA method and shared key, orelse the network will not unction properly
Security Mode > WPA Personal
WPA Algorthm WPA supports two encryption methods,TKIP and AES, with dynamic encryption keys Select thetype o algorithm, TKIP or AES The deault is TKIP
WPA Shared Key Enter a WPA Shared Key o 8-63characters
Group Key Renewal Enter a Group Key Renewal period,which instructs the Router how oten it should change theencryption keys The deault Group Key Renewal period is3600 seconds
WPA Enterprise
This option eatures WPA used in coordination with aRADIUS server (This should only be used when a RADIUSserver is connected to the Router)
-
7/28/2019 Wrt54gl v11 Ug Nc
14/32
Chapter3 Advanced Configuration
Wreless-G Broadband Router
Security Mode > WPA Enterprise
WPA Algorthm WPA supports two encryption methods,TKIP and AES, with dynamic encryption keys Select thetype o algorithm, TKIP or AES The deault is TKIP
RADIUS Server Address Enter the IP Address o theRADIUS server
RADIUS Port Enter the port number o the RADIUSserver The deault value is 8
Shared Key Enter the key shared between the Routerand the server
Key Renewal Tmeout Enter a Key Renewal Timeoutperiod, which instructs the Router how oten it shouldchange the encryption keys The deault Key RenewalTimeout period is 3600 seconds
WPA2 Personal
Security Mode > WPA2 Personal
WPA Algorthm WPA2 supports two encryptionmethods, TKIP and AES, with dynamic encryption keys
Select the type o algorithm, AES, or TKIP + AES Thedeault selection is TKIP + AES
WPA Shared Key Enter a WPA Shared Key o 8-63characters
Group Key Renewal Enter a Group Key Renewal period,which instructs the Router how oten it should change theencryption keys The deault Group Key Renewal period is3600 seconds
WPA2 Enterprise
This option eatures WPA2 used in coordination with aRADIUS server (This should only be used when a RADIUSserver is connected to the Router)
Security Mode > WPA2 Enterprise
WPA Algorthm WPA2 supports two encryptionmethods, TKIP and AES, with dynamic encryption keysSelect the type o algorithm, AES, or TKIP + AES Thedeault selection is TKIP + AES
RADIUS Server Address Enter the IP Address o theRADIUS server
RADIUS Port Enter the port number o the RADIUSserver The deault value is 8
Shared Key Enter the key shared between the Routerand the server
Key Renewal Tmeout Enter a Key Renewal Timeout
period, which instructs the Router how oten it shouldchange the encryption keys The deault Key RenewalTimeout period is 3600 seconds
RADIUS
This option eatures WEP used in coordination with aRADIUS server (This should only be used when a RADIUSserver is connected to the Router)
Security Mode > RADIUS
-
7/28/2019 Wrt54gl v11 Ug Nc
15/32
Chapter3 Advanced Configuration
Wreless-G Broadband Router
IMPORTANT: If you are using WEP encryption,
always remember that each device in your
wireless network MUST use the same WEP
encryption method and encryption key, or else
your wireless network will not function properly
RADIUS Server Address Enter the IP Address o theRADIUS server
RADIUS Port Enter the port number o the RADIUSserver The deault value is 8
Shared Key Enter the key shared between the Routerand the server
Default Transmt Key Select a Deault Transmit Key(choose which Key to use) The deault is
WEP Encrypton Select a level o WEP encryption,64 bts 0 hex dgts or 8 bts 6 hex dgts Thedeault is 64 bts 0 hex dgts
Passphrase Enter a Passphrase to automatically generateWEP keys Then clickGenerate
Key -4 I you did not enter a Passphrase, enter the WEPkey(s) manually
WEP
WEP is a basic encryption method, which is not as secureas WPA
Security Mode > WEP
Default Transmt Key Select a Deault Transmit Key
(choose which Key to use) The deault is
WEP Encrypton Select a level o WEP encryption, 64 bts0 hex dgts or 8 bts 6 hex dgts The deault is64 bts 0 hex dgts
Passphrase Enter a Passphrase to automatically generateWEP keys Then clickGenerate
Key -4 I you did not enter a Passphrase, enter the WEPkey(s) manually
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Wireless > Wireless MAC Filter
Wireless access can be filtered by using the MAC addresses of
the wireless devices transmitting within your networks radius
Wireless > Wireless MAC Filter
Wireless MAC Filter
Wreless MAC Flter To filter wireless users by MAC Address,either permitting or blocking access, clickEnable If you do
not wish to filter users by MAC Address, keep the default
setting, Dsable
Prevent Select this to block wireless access by MACAddress This button is selected by deault
Permt Only Select this to allow wireless access by MACAddress This button is not selected by deault
Edt MAC Flter Lst Click this to open the MAC AddressFilter List screen On this screen, you can list users, by MAC
Address, to whom you wish to provide or block access For
easy reference, clickWreless Clent MAC Lst to display a listof network users by MAC Address
MAC Address Filter List
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
-
7/28/2019 Wrt54gl v11 Ug Nc
16/32
Chapter3 Advanced Configuration
3Wreless-G Broadband Router
Wireless > Advanced Wireless Settings
This Wireless > Advanced Wireless Settings screen is usedto set up the Routers advanced wireless unctions Thesesettings should only be adjusted by an expert administratoras incorrect settings can reduce wireless perormance
Wireless > Advanced Wireless Settings
Advanced Wireless
Authentcaton Type The deault is set to Auto, whichallows either Open System or Shared Key authenticationto be used With Open System authentication, the senderand the recipient do NOT use a WEP key or authenticationWith Shared Key authentication, the sender and recipientuse a WEP key or authentication
Basc Rate The Basic Rate setting is not actually one rate
o transmission but a series o rates at which the Routercan transmit The Router will advertise its Basic Rate to theother wireless devices in your network, so they know whichrates will be used The Router will also advertise that it willautomatically select the best rate or transmission Thedeault setting is Default, when the Router can transmitat all standard wireless rates (1-2Mbps, 55Mbps, 11Mbps,18Mbps, and 24Mbps) Other options are -Mbps, oruse with older wireless technology, and All, when theRouter can transmit at all wireless rates The Basic Rateis not the actual rate o data transmission I you want tospeciy the Routers rate o data transmission, conigurethe Transmission Rate setting
Transmsson Rate The rate o data transmission shouldbe set depending on the speed o your wireless networkYou can select rom a range o transmission speeds, or youcan select Auto to have the Router automatically use theastest possible data rate and enable the Auto-Fallbackeature Auto-Fallback will negotiate the best possibleconnection speed between the Router and a wirelessclient The deault value is Auto
CTS Protecton Mode CTS (Clear-To-Send) ProtectionMode should remain disabled unless you are having severeproblems with your Wireless-G products not being able
to transmit to the Router in an environment with heavy80211b traic This unction boosts the Routers abilityto catch all Wireless-G transmissions but will severelydecrease perormance
Frame Burst Enabling this option should provide yournetwork with greater perormance, depending on the
manuacturer o your wireless products To turn on theFrame Burst option, select Enable The deault is Dsable
Beacon Interval The deault value is 00 Enter a valuebetween 1 and 65,535 milliseconds The Beacon Intervalvalue indicates the requency interval o the beacon Abeacon is a packet broadcast by the Router to synchronizethe wireless network
DTIM Interval This value, between 1 and 255, indicatesthe interval o the Delivery Traic Indication Message(DTIM) A DTIM ield is a countdown ield inormingclients o the next window or listening to broadcastand multicast messages When the Router has buered
broadcast or multicast messages or associated clients, itsends the next DTIM with a DTIM Interval value Its clientshear the beacons and awaken to receive the broadcastand multicast messages The deault value is
Fragmentaton Threshold This value speciies themaximum size or a packet beore data is ragmentedinto multiple packets I you experience a high packeterror rate, you may slightly increase the FragmentationThreshold Setting the Fragmentation Threshold too lowmay result in poor network perormance Only minorreduction o the deault value is recommended In mostcases, it should remain at its deault value o346
RTS Threshold Should you encounter inconsistent datalow, only minor reduction o the deault value, 34, isrecommended I a network packet is smaller than thepreset RTS threshold size, the RTS/CTS mechanism willnot be enabled The Router sends Request to Send (RTS)rames to a particular receiving station and negotiatesthe sending o a data rame Ater receiving an RTS, thewireless station responds with a Clear to Send (CTS) rameto acknowledge the right to begin transmission The RTSThreshold value should remain at its deault value o34
AP Isolaton This isolates all wireless clients and wireless
devices on your network rom each other Wireless deviceswill be able to communicate with the Router but not witheach other To use this unction, select On AP Isolation isturned Offby deault
SecureEasySetup This eature allows you to enable ordisable the SecureEasySetup eature Select Dsabled todisable the eature and turn o the buttons light Theeature is Enabled by deault
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
-
7/28/2019 Wrt54gl v11 Ug Nc
17/32
Chapter3 Advanced Configuration
4Wreless-G Broadband Router
Security > Firewall
The Security > Firewallscreen is used to conigure a irewallthat can ilter out various types o unwanted traic on theRouters local network
Security > Firewall
Firewall
Frewall Protecton To use irewall protection, keep thedeault selection, Enable To turn o irewall protection,select Dsable
Block WAN Requests
Block Anonymous Internet Requests This eaturemakes it more diicult or outside users to work theirway into your network This eature is selectedby deaultDeselect the eature to allow anonymous Internetrequests
Flter Multcast Multicasting allows or multiple
transmissions to speciic recipients at the same time Imulticasting is permitted, then the Router will allow IPmulticast packets to be orwarded to the appropriatecomputers This eature is selected by deault Deselectthis eature to disable it
Flter Internet NAT Redrecton This eature usesport orwarding to block access to local servers romlocal networked computers Select Flter Internet NATRedrecton to ilter Internet NAT redirection This eatureis not selected by deault
Flter IDENT (Port 3) This eature keeps port 113 rombeing scanned by devices outside o your local network
This eature is selected by deault Deselect this eature todisable it
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Security > VPN Passthrough
The Security > VPN Passthrough screen allows you to enable
VPN tunnels using IPSec, PPTP, or L2TP protocols to pass
through the Routers firewall
Security > VPN Passthrough
VPN Passthrough
IPSec Passthrough Internet Protocol Security (IPSec) isa suite o protocols used to implement secure exchangeo packets at the IP layer To allow IPSec tunnels to passthrough the Router, keep the deault, Enable
PPTP Passthrough Point-to-Point Tunneling Protocol(PPTP) allows the Point-to-Point Protocol (PPP) to betunneled through an IP network To allow PPTP tunnels topass through the Router, keep the deault, Enable
LTP Passthrough Layer 2 Tunneling Protocol is themethod used to enable Point-to-Point sessions via theInternet on the Layer 2 level To allow L2TP tunnels to passthrough the Router, keep the deault, Enable
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
-
7/28/2019 Wrt54gl v11 Ug Nc
18/32
Chapter3 Advanced Configuration
Wreless-G Broadband Router
Access Restrictions > Internet Access
The Access Restrictions > Internet Access screen allows youto block or allow speciic kinds o Internet usage andtraic, such as Internet access, designated services, andwebsites during speciic days and times
Access Restrictions > Internet Access
Internet Access
Internet Access Polcy Access can be managed by apolicy Use the settings on this screen to establish anaccess policy (ater Save Settngs is clicked) Selecting apolicy rom the drop-down menu will display that policyssettings To delete a policy, select that policys numberand clickDelete To view all the policies, clickSummary(Policies can be deleted rom the Summary screen byselecting the policy or policies and clicking Delete Toreturn to the Internet Access tab, clickClose)
Internet Policy Summary
Status Policies are disabled by deault To enable a policy,select the policy number rom the drop-down menu, andselect Enable
To create an Internet Access policy:
Select a number rom the Internet Access Policy drop-down menu
1
To enable this policy, select Enable
Enter a Policy Name in the ield provided
ClickEdt Lst of PCs to select which PCs will be affected
by the policy The List of PCs screen appears You can
select a PC by MAC Address or IP Address You can also
enter a range of IP Addresses if you want this policy
to affect a group of PCs After making your changes,click Save Settngs to apply your changes or Cancel
Changes to cancel your changes Then clickClose
List o PCs
Select the appropriate option, Deny or Allow,depending on whether you want to block or allowInternet access or the PCs you listed on the List of PCsscreen
Decide which days and what times you want this policyto be enorced Select the individual days during whichthe policy will be in eect, or select Everyday Thenenter a range o hours and minutes during which thepolicy will be in eect, or select 4 Hours
Select any Blocked Services or Website Blocking youwish to use
Click Save Settngs to save the policys settings, orclickCancel Changes to cancel the policys settings
Blocked Services
You can ilter access to various services accessed over theInternet, such as FTP or telnet, by selecting services romthe drop-down menus next to Blocked Services (You canblock up to 20 services) Then enter the range o ports youwant to ilter
I the service you want to block is not listed or you want toedit a services settings, then clickAdd/Edt Servce Thenthe Port Services screen will appear
Port Services
2
3
4
5
6
7
8
-
7/28/2019 Wrt54gl v11 Ug Nc
19/32
Chapter3 Advanced Configuration
6Wreless-G Broadband Router
To add a service, enter the services name in the ServiceName ield Select its protocol rom the Protocol drop-down menu, and enter its range in the Port Range ieldsThen clickAdd
To modiy a service, select it rom the list on the rightChange its name, protocol setting, or port range Then
clickModfyTo delete a service, select it rom the list on the right ThenclickDelete
When you are inished making changes on the PortServices screen, click Apply to save the changes I youwant to cancel your changes, click Cancel To close thePort Services screen and return to the Access Restrictionsscreen, clickClose
Website Blocking by URL Address
I you want to block websites with speciic URL addresses,
enter each URL in a separate ield next to Website Blockingby URL Address
Website Blocking by Keyword
I you want to block websites using speciic keywords,enter each keyword in a separate ield next to WebsiteBlocking by Keyword
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Applications and Gaming > Port Range
ForwardThe Applications & Gaming > Port Range Forward screen
allows you to set up public services on your network, such as
web servers, ftp servers, e-mail servers, or other specialized
Internet applications (Specialized Internet applications are
any applications that use Internet access to perform functions
such as videoconferencing or online gaming Some Internet
applications may not require any forwarding)
Applications and Gaming > Port Range Forward
Port Range Forward
To orward a port, enter the inormation on each line orthe criteria required
Applcaton In this ield, enter the name you wish to givethe application Each name can be up to 12 characters
Start/End This is the port range Enter the number thatstarts the port range in the Start column and the numberthat ends the range in the End column
Protocol Select the protocol used or this application,either TCP or UDP, or Both
IP Address For each application, enter the IP Address othe PC running the speciic application
Enable Select Enable to enable port orwarding or therelevant application
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Applications & Gaming > Port Triggering
The Applications & Gaming > Port Triggering screen allowsthe Router to watch outgoing data or speciic portnumbers The IP address o the computer that sends thematching data is remembered by the Router, so that whenthe requested data returns through the Router, the data ispulled back to the proper computer by way o IP addressand port mapping rules
Applications and Gaming > Port Triggering
Port Triggering
Applcaton Enter the application name o the trigger
Triggered Range
For each application, list the triggered port number rangeCheck with the Internet application documentation orthe port number(s) needed
-
7/28/2019 Wrt54gl v11 Ug Nc
20/32
Chapter3 Advanced Configuration
Wreless-G Broadband Router
Start Port Enter the starting port number o the TriggeredRange
End Port Enter the ending port number o the TriggeredRange
Forwarded Range
For each application, list the orwarded port numberrange Check with the Internet application documentationor the port number(s) needed
Start Port Enter the starting port number o theForwarded Range
End Port Enter the ending port number o the ForwardedRange
Enable Select Enable to enable port triggering or theapplicable application
ClickSave Settngs to apply your changes, or clickCancel
Changesto cancel your changes
Applications and Gaming > DMZ
The DMZ eature allows one network computer to beexposed to the Internet or use o a special-purposeservice such as Internet gaming or videoconerencingDMZ hosting orwards all the ports at the same time toone PC The Port Range Forward eature is more securebecause it only opens the ports you want to have opened,while DMZ hosting opens all the ports o one computer,exposing the computer to the Internet
Applications and Gaming > DMZ
DMZ
Any PC whose port is being orwarded must have its DHCP
client unction disabled and should have a new static IPaddress assigned to it because its IP address may changewhen using the DHCP unction
To expose one PC, select Enable Then, enter thecomputers IP address in the DMZ Host IP Address ield Thiseature is disabled by deault
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Applications and Gaming > QoS
Quality o Service (QoS) ensures better service tohigh-priority types o network traic, which mayinvolve demanding, real-time applications, such asvideoconerencing
There are three types o QoS available: Device Priority,Ethernet Port Priority, and Application Priority
Wired QoS
Enable/Dsable To enable QoS, select Enable Otherwise,select Dsable QoS is disabled by deault
Upstream Bandwdth Select Auto or Manual romthe drop-down menu Manual allows you to speciy themaximum outgoing bandwidth that applications canutilize
Applications and Gaming > QoS
Device Priority
Enter the name o your network device in the Device nameield, enter its MAC Address, and then select its priorityrom the drop-down menu
Ethernet Port Priority
Ethernet Port Priority QoS allows you to prioritizeperormance or the Routers our ports, LAN Ports 1-4 Foreach port, select the priority and low control setting
-
7/28/2019 Wrt54gl v11 Ug Nc
21/32
Chapter3 Advanced Configuration
8Wreless-G Broadband Router
Prorty Select Hgh or Low in the Priority column TheRouters our ports have been assigned low priority bydeault
Flow Control I you want the Router to control thetransmission o data between network devices, selectEnabled To disable this eature, select Dsabled Ethernet
Port Priority QoS does not require support rom your ISPbecause the prioritized ports LAN ports 1-4 are in yournetwork This eature is enabled by deault
Application Priority
Application Priority QoS manages inormation as it istransmitted and received Depending on the settings othe QoS screen, this eature will assign inormation a highor low priority or the applications that you speciy
Optmze Gamng Applcatons Select this toautomatically allow common game application portsto have a higher priority These games include, but are
not limited to: Counter-Strike , Half-Life, Age of Empires,Everquest, Quake2/Quake3, and Diablo II The deaultsetting is unselected
Applcaton Name Enter the name you wish to give theapplication in theApplication Name ield
Prorty Select Hgh or Low to assign priority to theapplication The deault selection is Low
Specfc Port # Enter the port number or theapplication
Wireless QoS
WMM Support Wi-Fi Multimedia (WMM), ormerlyknown as Wireless Multimedia Extensions (WME), isa Wi-Fi Alliance certiied eature, based on the IEEE80211e standard This eature provides QoS to wirelessnetworks It is especially suitable or voice, music andvideo applications; or example, Voice over IP ( VoIP), videostreaming, and interactive gaming I you have otherdevices on your wireless network that support WMM,select Enabled Otherwise, keep the deault, Dsabled
No Acknowledgement This eature prevents the Routerrom re-sending data i an error occurs To use this eature,select Enabled Otherwise, keep the deault setting,
Dsabled
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Administration > Management
The Administration > Management screen allows thenetworks administrator to manage speciic Routerunctions or access and security
Administration > Management
Router Password
Local Router Access
Router Password Enter a new Password or the Router
Re-enter to confrm Enter the Password again to confirm
Web Access
Access Server HTTP (HyperText Transport Protocol) isthe communications protocol used to connect to serverson the World Wide Web HTTPS uses SSL (Secured SocketLayer) to encrypt data transmitted or higher securitySelect HTTP or HTTPS. The deault selection is HTTP
Wreless Access Web I you are using the Router ina public domain where you are giving wireless accessto your guests, you can disable wireless access to theRouters web-based utility You will only be able to accessthe web-based utility via a wired connection i you disablethe setting Keep the deault, Enable, to enable wirelessaccess to the Routers web-based utility, or select Dsableto disable wireless access to the utility
Remote Router Access
Remote Management To access the Router remotely,rom outside the network, select Enable
Management Port Enter the port number that will beopen to outside access You will need to enter the Routerspassword when accessing the Router this way, as usual
Use https To require the use o HTTPS or remote access,select this eature
UPnP
UPnP Keep the deault, Enable to enable the UPnPeature; otherwise, select Dsable
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
-
7/28/2019 Wrt54gl v11 Ug Nc
22/32
Chapter3 Advanced Configuration
9Wreless-G Broadband Router
Administration > Log
The Router can keep logs o all traic or your Internetconnection
Administration > Log
Log
Log To disable the Log unction, keep the deault setting,
Dsable To monitor traic between the network and theInternet, select Enable
When you wish to view the logs, click Incomng Log orOutgong Log, depending on which you wish to view
ClickSave Settngs to apply your changes, or clickCancelChanges to cancel your changes
Administration > Diagnostics
The diagnostic tests (Ping and Traceroute) allow you tocheck the connections o your network components
Administration > Diagnostics
Ping Test
Png The Ping test checks the status o a connectionClickPng to open the Ping Testscreen Enter the addresso the PC whose connection you wish to test and howmany times you wish to test it Then, click Png The PingTestscreen will show i the test was successul To stop thetest, clickStop ClickClear Log to clear the screen ClickClose to return to the Diagnostics screen
The Ping Test
Traceroute Test
Traceroute To test the perormance o a connection,clickTraceroute to open the Traceroute Testscreen Enterthe address o the PC whose connection you wish to testand clickTraceroute The Traceroute Testscreen will show
i the test was successul To stop the test, clickStop ClickClear Log to clear the screen ClickClose to return to theDiagnostics screen
The Traceroute Test
Administration > Factory Deaults
The Administration > Factory Defaults screen allows youto restore the Routers coniguration to its actory deaultsettings
Factory Deaults
Restore Factory Defaults To reset the Routers settingsto the deault values, select Yes, and then click SaveSettngs Any settings you have saved will be lost whenthe deault settings are restored
Administration > Factory Deaults
-
7/28/2019 Wrt54gl v11 Ug Nc
23/32
Chapter3 Advanced Configuration
0Wreless-G Broadband Router
Administration > Firmware Upgrade
The Administration > Firmware Upgrade screen allows you
to upgrade the Routers firmware Do not upgrade the
firmware unless you are experiencing problems with the
Router or the new firmware has a feature you want to use
Administration > Firmware Upgrade
Beore upgrading the irmware, download the Routersirmware upgrade ile rom the Linksys website, wwwlinksyscom Then extract the ile
Upgrade Firmware
Please select a fle to upgrade ClickBrowse and selectthe extracted irmware upgrade ile Then clickUpgradeand follow the on-screen instructions
Administration > Conig Management
This screen is used to back up or restore the Routers
coniguration ile
Administration > Conig Management
Backup Coniguration
To back up the Routers coniguration ile, click BackupThen ollow the on-screen instructions
Restore Coniguration
Please select a fle to restore Click Browse and selectthe coniguration ile Then clickRestore
Status > Router
The Status > Router screen displays the Routers currentstatus
Administration > Factory Deaults
Router Inormation
Frmware Verson This is the Routers current irmware
Current Tme This shows the time, as you set on theSetup tab
MAC Address This is the Routers MAC Address, as seenby your ISP
Router Name This is the speciic name or the Router,which you set on the Setup tab
Host Name I required by your ISP, this would have beenentered on the Setup tab
Doman Name I required by your ISP, this would havebeen entered on the Setup tab
Internet
Configuration Type
This section shows the current network inormationstored in the Router The inormation varies depending onthe Internet connection type selected on the Setup > BasicSetup screen
ClickRefresh to update the on-screen inormation
-
7/28/2019 Wrt54gl v11 Ug Nc
24/32
Chapter3 Advanced Configuration
Wreless-G Broadband Router
Status > Local Network
The Status > Local Network screen displays the status oyour network
Status > Local Network
Local NetworkMAC Address This is the Routers MAC Address, as seenon your local, Ethernet network
IP Address This shows the Routers IP Address, as itappears on your local, Ethernet network
Subnet Mask This shows the current subnet mask beingconigured or your local network
DHCP Server I you are using the Router as a DHCP server,that will be displayed here
Start IP Address For the range o IP Addresses used by
devices on your local, Ethernet network, the beginning othat range is shown here
End IP Address For the range o IP Addresses used bydevices on your local, Ethernet network, the end o thatrange is shown here
DHCP Clents Table Clicking this button will open ascreen to show you which PCs are utilizing the Router as aDHCP server You can delete PCs rom that list, and severtheir connections, by checking a Delete box and clickingthe Delete button
DHCP Clients Table
ClickRefresh to update the on-screen inormation
Status > Wireless
The Status > Wireless screen displays the status o yourwireless network
Status > Wireless
Wireless
MAC Address This is the Routers MAC Address, as seenon your local, wireless network
Mode As selected rom the Wireless > Basic WirelessSettings screen, this displays the wireless mode (Mixed, G-Only, or Disabled) used by the network
SSID As entered on the Wireless > Basic Wireless Settingsscreen, this displays the wireless network name or SSID
DHCP Server The status o the DHCP server unction isdisplayed here
Channel As entered on the Wireless > Basic WirelessSettings screen, this displays the channel on which your
wireless network is broadcasting
Encrypton Functon As selected on the Wireless >Wireless Security screen, this displays the status o theRouters wireless security
ClickRefresh to update the on-screen inormation
-
7/28/2019 Wrt54gl v11 Ug Nc
25/32
AppendixA Troubleshooting
Wreless-G Broadband Router
Appendx A:Troubleshootng
Your computer cannot connect to the Internet.
Follow these instructions until your computer can connectto the Internet:
Make sure that the Router is powered on The PowerLED should be green and not lashing
I the Power LED is lashing, then power o all oyour network devices, including the modem, Router,and computers Then power on each device in theollowing order:
Cable or DSL modem
Router
ComputerCheck the cable connections The computer shouldbe connected to one o the ports numbered 1-4 onthe Router, and the modem must be connected to theInternet port on the Router
The modem does not have an Ethernet port.
The modem is a dial-up modem or traditional dial-upservice To use the Router, you need a cable/DSL modemand high-speed Internet connection
You cannot use the DSL service to connect manually to
the Internet.
Ater you have installed the Router, it will automaticallyconnect to your Internet Service Provider (ISP), so you nolonger need to connect manually
The DSL telephone line does not ft into the Routers
Internet port.
The Router does not replace your modem You still needyour DSL modem in order to use the Router Connectthe telephone line to the DSL modem, insert the setupCD into your computer, and then ollow the on-screeninstructions
1
2
3
When you double-click the web browser, you are
prompted or a username and password. I you want to
get rid o the prompt, ollow these instructions.
Launch the web browser and perorm the ollowing steps(these steps are speciic to Internet Explorer but are similaror other browsers):
Select Tools > Internet Optons
Click the Connectons tab
Select Never dal a connecton
ClickOK
The Router does not have a coaxial port or the cable
connection.
The Router does not replace your modem You still needyour cable modem in order to use the Router Connect yourcable connection to the cable modem, insert the setup
CD into your computer, and then ollow the on-screeninstructions
The computer cannot connect wirelessly to the network.
Make sure the wireless network name or SSID is the sameon both the computer and the Router I you have enabledwireless security, then make sure the same securitymethod and key are used by both the computer and theRouter
You need to modiy the settings on the Router.
Open the web browser (or example, Internet Explorer or
Fireox), and enter the Routers IP address in the addressield (the deault IP address is 9.68..) Whenprompted, leave the User name ield blank and enter thepassword to the Router (the deault is admn) Click theappropriate tab to change the settings
WEB: I your questions are not addressed here,reer to the Linksys website, www.lnksys.com
1
2
3
4
-
7/28/2019 Wrt54gl v11 Ug Nc
26/32
AppendixB Specifications
3Wreless-G Broadband Router
Appendx B:Specfcatons
Model WRT54GL
Standards IEEE 8023, IEEE 8023u,IEEE 80211g, IEEE 80211b
Channels 11 Channels (US, Canada)13 Channels (Europe, Japan)
Ports Internet: One 10/100 RJ-45 PortLAN: Four 10/100 RJ-45 SwitchedPortsOne Power Port
Button Reset, SecureEasySetup
Cabling Type CAT5
LEDs Power, DMZ, WLAN, LAN (1-4),Internet, SecureEasySetup
RF Power Output 18 dBm
UPnP able/cert Able
Security Features Stateul Packet Inspection (SPI)Firewall, Internet Policy
Wireless Security Wi-Fi Protected Access2 (WPA2),WEP, Wireless MAC Filtering
Envronmental
Dimensions 732" x 189" x 606"(186 x 48 x 154 mm)
Weight 138 oz (391 g)
Power External, 12V DC, 05A
Certifcations FCC, IC-03, CE, Wi-Fi (80211b,80211g), WPA2, WMM
Operating Temp 32 to 104F (0 to 40C)
Storage Temp -4 to 158F (-20 to 70C)
Operating Humidity 10 to 85%, Noncondensing
Storage Humidity 5 to 90%, Noncondensing
-
7/28/2019 Wrt54gl v11 Ug Nc
27/32
AppendixC Warranty and Regulatory Information
4Wreless-G Broadband Router
Appendx C:Warranty and RegulatoryInformaton
Limited Warranty
Linksys warrants to You that, or a period o one year(the "Warranty Period"), your Linksys Product will besubstantially ree o deects in materials and workmanshipunder normal use Your exclusive remedy and Linksysentire liability under this warranty will be or Linksys atits option to repair or replace the Product or reund Yourpurchase price less any rebates This limited warrantyextends only to the original purchaser
I the Product proves deective during the WarrantyPeriod call Linksys Technical Support in order to obtain
a Return Authorization Number, i applicable BE SURETO HAVE YOUR PROOF OF PURCHASE ON HAND WHENCALLING I You are requested to return the Product, markthe Return Authorization Number clearly on the outsideo the package and include a copy o your original prooo purchase RETURN REQUESTS CANNOT BE PROCESSEDWITHOUT PROOF OF PURCHASE You are responsibleor shipping deective Products to Linksys Linksys paysor UPS Ground shipping rom Linksys back to You onlyCustomers located outside o the United States o Americaand Canada are responsible or all shipping and handlingcharges
ALL IMPLIED WARRANTIES AND CONDITIONS OFMERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE ARE LIMITED TO THE DURATION OFTHE WARRANTY PERIOD ALL OTHER EXPRESS ORIMPLIED CONDITIONS, REPRESENTATIONS ANDWARRANTIES, INCLUDING ANY IMPLIED WARRANTY OFNON-INFRINGEMENT, ARE DISCLAIMED Some jurisdictionsdo not allow limitations on how long an implied warrantylasts, so the above limitation may not apply to You Thiswarranty gives You speciic legal rights, and You may alsohave other rights which vary by jurisdiction
This warranty does not apply i the Product (a) has been
altered, except by Linksys, (b) has not been installed,operated, repaired, or maintained in accordance withinstructions supplied by Linksys, or (c) has been subjectedto abnormal physical or electrical stress, misuse,negligence, or accident In addition, due to the continualdevelopment o new techniques or intruding upon andattacking networks, Linksys does not warrant that theProduct will be ree o vulnerability to intrusion or attack
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENTWILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUEOR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THETHEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISINGOUT OF OR RELATED TO THE USE OF OR INABILITY TO
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVENIF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OFSUCH DAMAGES IN NO EVENT WILL LINKSYS LIABILITYEXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCTThe oregoing limitations will apply even i any warranty orremedy provided under this Agreement ails o its essentialpurpose Some jurisdictions do not allow the exclusion orlimitation o incidental or consequential damages, so theabove limitation or exclusion may not apply to You
Please direct all inquiries to: Linksys, PO Box 18558, Irvine,CA 92623
-
7/28/2019 Wrt54gl v11 Ug Nc
28/32
AppendixC Warranty and Regulatory Information
Wreless-G Broadband Router
Wireless Disclaimer
The maximum perormance or wireless is derived romIEEE Standard 80211 speciications Actual perormancecan vary, including lower wireless network capacity,data throughput rate, range and coverage Perormance
depends on many actors, conditions and variables,including distance rom the access point, volume onetwork traic, building materials and construction,operating system used, intererence and other adverseconditions
FCC Statement
This product has been tested and complies with thespeciications or a Class B digital device, pursuant to Part15 o the FCC Rules These limits are designed to providereasonable protection against harmul intererence ina residential installation This equipment generates,
uses, and can radiate radio requency energy and, i notinstalled and used according to the instructions, maycause harmul intererence to radio communicationsHowever, there is no guarantee that intererence will notoccur in a particular installation I this equipment doescause harmul intererence to radio or television reception,which is ound by turning the equipment o and on, theuser is encouraged to try to correct the intererence byone or more o the ollowing measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment ordevices
Connect the equipment to an outlet other than thereceivers
Consult a dealer or an experienced radio/TV technicianor assistance
Saety Notices
Caution: To reduce the risk o ire, use only No26 AWG orlarger telecommunication line cord
Do not use this product near water, or example, in a wetbasement or near a swimming pool
Avoid using this product during an electrical storm Theremay be a remote risk o electric shock rom lightning
WARNING: This product contains lead, knownto the State o Caliornia to cause cancer, andbirth deects or other reproductive harm Washhands ater handling
Industry Canada (Canada)
This device complies with Industry Canada ICES-003 rule
Cet appareil est conorme la norme NMB003 dIndustrieCanada
IC StatementOperation is subject to the ollowing two conditions:
This device may not cause intererence and
This device must accept any intererence, includingintererence that may cause undesired operation othe device
Rglement dIndustry Canada
Le onctionnement est soumis aux conditions suivantes :
Ce priphrique ne doit pas causer dinterrences;
Ce priphrique doit accepter toutes les interrencesreues, y compris celles qui risquent dentraner unonctionnement indsirable
1
2
1
2
-
7/28/2019 Wrt54gl v11 Ug Nc
29/32
AppendixC Warranty and Regulatory Information
6Wreless-G Broadband Router
User Inormation or Consumer Products
Covered by EU Directive 2002/96/EC on
Waste Electric and Electronic Equipment
(WEEE)
This document contains important inormation or userswith regards to the proper disposal and recycling oLinksys products Consumers are required to comply withthis notice or all electronic products bearing the ollowingsymbol:
Englsh - Envronmental Informaton for Customers nthe European Unon
European Directive 2002/96/EC requires that the equipmentbearing this symbol on the product and/or its packaging mustnot be disposed o with unsorted municipal waste The symbolindicates that this product should be disposed o separatelyrom regular household waste streams It is your responsibility todispose o this and other electric and electronic equipment viadesignated collection acilities appointed by the government orlocal authorities Correct disposal and recycling will help preventpotential negative consequences to the environment andhuman health For more detailed inormation about the disposal
o your old equipment, please contact your local authorities,waste disposal service, or the shop where you purchased theproduct
(Bulgaran) -
2002/96/EC , / , ,
- , ,
Cetna (Czech) - Informace o ochran votnhoprosted pro zkaznky v zemch Evropsk une
Evropsk smrnice 2002/96/ES zakazuje, aby zazen oznaentmto symbolem na produktu anebo na obalu bylo likvidovnos netdnm komunlnm odpadem Tento symbol udv,e dan produkt mus bt likvidovn oddlen od bnhokomunlnho odpadu Odpovdte za likvidaci tohoto produktu
a dalch elektrickch a elektronickch zazen prostednictvmurench sbrnch mst stanovench vldou nebo mstnmiady Sprvn likvidace a recyklace pomh pedchzetpotencilnm negativnm dopadm na ivotn prosted a lidskzdrav Podrobnj inormace o likvidaci starho vybaven silaskav vydejte od mstnch ad, podniku zabvajcho selikvidac komunlnch odpad nebo obchodu, kde jste produktzakoupili
Dansk (Dansh) - Mljnformaton for kunder EU
EU-direktiv 2002/96/EF krver, at udstyr der brer dette symbolp produktet og/eller emballagen ikke m bortskaes som
usorteret kommunalt aald Symbolet betyder, at dette produkt
skal bortskaes adskilt ra det almindelige husholdningsaaldDet er dit ansvar at bortskae dette og andet elektrisk ogelektronisk udstyr via bestemte indsamlingssteder udpegeta staten eller de lokale myndigheder Korrekt bortskaelseog genvinding vil hjlpe med til at undg mulige skader ormiljet og menneskers sundhed Kontakt venligst de lokalemyndigheder, renovationstjenesten eller den butik, hvor duhar kbt produktet, angende mere detaljeret inormation ombortskaelse a dit gamle udstyr
Deutsch (German) - Umweltnformaton fr Kundennnerhalb der Europschen Unon
Die Europische Richtlinie 2002/96/EC verlangt, dass technische
Ausrstung, die direkt am Gert und/oder an der Verpackung mitdiesem Symbol versehen ist , nicht zusammen mit unsortiertemGemeindeaball entsorgt werden dar Das Symbol weist darauhin, dass das Produkt von regulrem Haushaltmll getrenntentsorgt werden sollte Es liegt in Ihrer Verantwortung, diesesGert und andere elektrische und elektronische Gerte berdie dar zustndigen und von der Regierung oder rtlichenBehrden dazu bestimmten Sammelstellen zu entsorgenOrdnungsgemes Entsorgen und Recyceln trgt dazu bei,potentielle negative Folgen r Umwelt und die menschlicheGesundheit zu vermeiden Wenn Sie weitere Inormationen zurEntsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte andie rtlichen Behrden oder stdtischen Entsorgungsdiensteoder an den Hndler, bei dem Sie das Produkt erworben haben
-
7/28/2019 Wrt54gl v11 Ug Nc
30/32
AppendixC Warranty and Regulatory Information
Wreless-G Broadband Router
Eest (Estonan) - Keskkonnaalane nformatsoonEuroopa Ldus asuvatele klentdele
Euroopa Liidu direktiivi 2002/96/E nuete kohaselt onseadmeid, millel on tootel vi pakendil kesolev smbol ,keelatud krvaldada koos sorteerimata olmejtmetega Seesmbol nitab, et toode tuleks krvaldada eraldi tavalistestolmejtmevoogudest Olete kohustatud krvaldama kesoleva
ja ka muud elektri- ja elektroonikaseadmed riigi vi kohalikeametiasutuste poolt ette nhtud kogumispunktide kauduSeadmete korrektne krvaldamine ja ringlussevtt aitab vltidavimalikke negatiivseid tagajrgi keskkonnale ning inimestetervisele Vanade seadmete krvaldamise kohta tpsemainormatsiooni saamiseks vtke palun hendust kohalikeametiasutustega, jtmekitlusirmaga vi kauplusega, kust tetoote ostsite
Espaol (Spansh) - Informacn medoambental paraclentes de la Unn Europea
La Directiva 2002/96/CE de la UE exige que los equipos quelleven este smbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos noseleccionados El smbolo indica que el producto en cuestindebe separarse de los residuos domsticos convencionales convistas a su eliminacin Es responsabilidad suya desechar este ycualesquiera otros aparatos elctricos y electrnicos a travs delos puntos de recogida que ponen a su disposicin el gobierno ylas autoridades locales Al desechar y reciclar correctamente estosaparatos estar contribuyendo a evitar posibles consecuenciasnegativas para el medio ambiente y la salud de las personas Sidesea obtener inormacin ms detallada sobre la eliminacinsegura de su aparato usado, consulte a las autoridades locales,al servicio de recogida y eliminacin de residuos de su zona opregunte en la tienda donde adquiri el producto
(Greek) -
2002/96/EC /
, ,
Franas (French) - Informatons envronnementalespour les clents de lUnon europenne
La directive europenne 2002/96/CE exige que lquipementsur lequel est appos ce symbole sur le produit et/ou sonemballage ne soit pas jet avec les autres ordures mnagres Cesymbole indique que le produit doit tre limin dans un circuitdistinct de celui pour les dchets des mnages Il est de votre
responsabilit de jeter ce matriel ainsi que tout autre matriellectrique ou lectronique par les moyens de collecte indiquspar le gouvernement et les pouvoirs publics des collectivitsterritoriales Llimination et le recyclage en bonne et due ormeont pour but de lutter contre limpact naste potentiel de cetype de produits sur lenvironnement et la sant publique Pourplus dinormations sur le mode dlimination de votre ancienquipement, veuillez prendre contact avec les pouvoirs publicslocaux, le service de traitement des dchets, ou lendroit o vousavez achet le produit
Italano (Italan) - Informazon relatve allambenteper clent resdent nellUnone Europea
La direttiva europea 2002/96/EC richiede che le apparecchiaturecontrassegnate con questo simbolo sul prodotto e/osullimballaggio non siano smaltite insieme ai riiuti urbaninon dierenziati Il simbolo indica che questo prodotto nondeve essere smaltito insieme ai normali riiuti domestici responsabilit del proprietario smaltire sia questi prodotti siale altre apparecchiature elettriche ed elettroniche mediantele speciiche strutture di raccolta indicate dal governo o daglienti pubblici locali Il corretto smaltimento ed il riciclaggioaiuteranno a prevenire conseguenze potenzialmente negativeper lambiente e per la salute dellessere umano Per ricevereinormazioni pi dettagliate circa lo smaltimento delle vecchieapparecchiature in Vostro possesso, Vi invitiamo a contattare glienti pubblici di competenza, il servizio di smaltimento riiuti o il
negozio nel quale avete acquistato il prodotto
Latveu valoda (Latvan) - Ekoloska nformcjaklentem Eropas Savenbas jursdkcj
Direktv 2002/96/EK ir prasba, ka aprkojumu, kam pievienotazme uz paa izstrdjuma vai uz t iesaiojuma, nedrkstizmest neirot veid kop ar komunlajiem atkritumiem(tiem, ko rada vietji iedzvotji un uzmumi) zme nozmto, ka ierce ir jizmet atkritumos t, lai t nenonktu kop arparastiem mjsaimniecbas atkritumiem Jsu pienkums ir oun citas elektriskas un elektroniskas ierces izmest atkritumos,izmantojot paus atkritumu savkanas veidus un ldzekus, konodroina valsts un pavaldbu iestdes Ja izmeana atkritumos
un prstrde tiek veikta pareizi, tad mazins iespjamaiskaitjums dabai un cilvku veselbai Skkas zias parnovecojua aprkojuma izmeanu atkritumos js varat saemtvietj pavaldb, atkritumu savkanas dienest, k ar veikal,kur iegdjties o izstrdjumu
-
7/28/2019 Wrt54gl v11 Ug Nc
31/32
AppendixC Warranty and Regulatory Information
8Wreless-G Broadband Router
Letuvka (Lthuanan) - Aplnkosaugos nformacja,skrta Europos Sjungos vartotojams
Europos direktyva 2002/96/EC numato, kad rangos, kuri irkurios pakuot yra paymta iuo simboliu (veskite simbol),negalima alinti kartu su neriuotomis komunalinmisatliekomis is simbolis rodo, kad gamin reikia alinti atskirainuo bendro buitini atliek srauto Js privalote utikrinti, kad
i ir kita elektros ar elektronin ranga bt alinama per tamtikras nacionalins ar vietins valdios nustatytas atliek rinkimosistemas Tinkamai alinant ir perdirbant atliekas, bus ivengtagalimos alos aplinkai ir moni sveikatai Daugiau inormacijosapie js senos rangos alinim gali pateikti vietins valdiosinstitucijos, atliek alinimo tarnybos arba parduotuvs, kuriosesigijote t gamin
Malt (Maltese) - Informazzjon Ambjental gal Kljentfl-Unjon Ewropea
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagmir li jkun ih is-simbolu uq il-prodott u/jew uq l-ippakkjar ma jistax jintremama skart muniipali li ma iex isseparat Is-simbolu jindika
li dan il-prodott gandu jintrema separatament minn ma l-iskart domestiku regolari Hija responsabbilt tiegek li tarmidan it-tagmir u kull tagmir ieor ta l-elettriku u elettronikupermezz ta ailitajiet ta bir appuntati apposta mill-gvern jewmill-awtoritajiet lokali Ir-rimi bmod korrett u r-riikla jginjipprevjeni konsegwenzi negattivi potenzjali gall-ambjent ugas-saa tal-bniedem Gal aktar inormazzjoni dettaljatadwar ir-rimi tat-tagmir antik tiegek, jekk jogbok ikkuntattjalill-awtoritajiet lokali tiegek, is-servizzi gar-rimi ta l-iskart, jewil-anut minn ejn xtrajt il-prodott
Magyar (Hungaran) - Krnyezetvdelm nformc azeurpa uns vsrlk szmra
A 2002/96/EC szm eurpai unis irnyelv megkvnja, hogyazokat a termkeket, amelyeken, s/vagy amelyek csomagolsnaz albbi cmke megjelenik, tilos a tbbi szelektlatlan lakossgihulladkkal egytt kidobni A cmke azt jelli, hogy az adotttermk kidobsakor a szokvnyos hztartsi hulladkelszlltsirendszerektl elklntett eljrst kell alkalmazni Az nelelssge, hogy ezt, s ms elektromos s elektronikusberendezseit a kormnyzati vagy a helyi hatsgok ltalkijellt gyjtredszereken keresztl szmolja el A megelelhulladkeldolgozs segt a krnyezetre s az emberi egszsgrepotencilisan rtalmas negatv hatsok megelzsben Haelavult berendezseinek elszmolshoz tovbbi rszletesinormcira van szksge, krjk, lpjen kapcsolatba a helyihatsgokkal, a hulladkeldolgozsi szolglattal, vagy azzal
zlettel, ahol a termket vsrolta
Nederlands (Dutch) - Mleu-nformate voor klantenn de Europese Une
De Europese Richtlijn 2002/96/EC schrijt voor dat apparatuur dieis voorzien van dit symbool op het product o de verpakking,niet mag worden ingezameld met niet-gescheiden huishoudelijkaval Dit symbool geet aan dat het product apart moet wordeningezameld U bent zel verantwoordelijk voor de vernietiging
van deze en andere elektrische en elektronische apparatuur via dedaarvoor door de landelijke o plaatselijke overheid aangewezeninzamelingskanalen De juiste vernietiging en recycling vandeze apparatuur voorkomt mogelijke negatieve gevolgen voorhet milieu en de gezondheid Voor meer inormatie over hetvernietigen van uw oude apparatuur neemt u contact op metde plaatselijke autoriteiten o avalverwerkingsdienst, o met dewinkel waar u het product hebt aangeschat
Norsk (Norwegan) - Mljnformasjon for kunder EU
EU-direktiv 2002/96/EF krever at utstyr med lgende symbolavbildet p produktet og/eller pakningen, ikke m kastes
sammen med usortert avall Symbolet indikerer at dette
produktet skal hndteres atskilt ra ordinr avallsinnsamlingor husholdningsavall Det er ditt ansvar kvitte deg meddette produktet og annet elektrisk og elektronisk avall via egneinnsamlingsordninger slik myndighetene eller kommunenebestemmer Korrekt avallshndtering og gjenvinning vilvre med p orhindre mulige negative konsekvenser ormilj og helse For nrmere inormasjon om hndtering avdet kasserte utstyret ditt, kan du ta kontakt med kommunen,en innsamlingsstasjon or avall eller butikken der du kjpteproduktet
Polsk (Polsh) - Informacja dla klentw w UnEuropejskej o przepsach dotyczcych ochrony
rodowskaDyrektywa Europejska 2002/96/EC wymaga, aby sprztoznaczony symbolem znajdujcym si na produkcie i/lub jegoopakowaniu nie by wyrzucany razem z innymi niesortowanymiodpadami komunalnymi Symbol ten wskazuje, e produktnie powinien by usuwany razem ze zwykymi odpadami zgospodarstw domowych Na Pastwu spoczywa obowizekwyrzucania tego i innych urzdze elektrycznych orazelektronicznych w punktach odbioru wyznaczonych przez wadzekrajowe lub lokalne Pozbywanie si sprztu we waciwy sposbi jego recykling pomog zapobiec potencjalnie negatywnymkonsekwencjom dla rodowiska i zdrowia ludzkiego W celuuzyskania szczeg