Model YHAP-C255EXE-2000EXW4S
2,500 - 20,000 KW
SINGLE EFFECT STEAM-FIRED ABSORPTION HEAT PUMP
INSTALLATION, OPERATION, MAINTENANCE
Supersedes: 155.36-ICOM2.EN.CE/GB (1118)
Form 155.36-ICOM2.EN.CE/GB (419)
Issue Date: April 05, 2019
LD27818
Original Instruction
JOHNSON CONTROLS2
FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
This equipment is a relatively complicated apparatus. During rigging, installation, operation, maintenance, or service, individuals may be exposed to certain com-ponents or conditions including, but not limited to: heavy objects, refrigerants, materials under pressure, rotating components, and both high and low voltage. Each of these items has the potential, if misused or handled improperly, to cause bodily injury or death. It is the obligation and responsibility of rigging, instal-lation, and operating/service personnel to identify and recognize these inherent hazards, protect themselves, and proceed safely in completing their tasks. Failure to comply with any of these requirements could result in serious damage to the equipment and the property in
IMPORTANT!READ BEFORE PROCEEDING!
GENERAL SAFETY GUIDELINES
which it is situated, as well as severe personal injury or death to themselves and people at the site.
This document is intended for use by owner-authorized rigging, installation, and operating/service personnel. It is expected that these individuals possess independent training that will enable them to perform their assigned tasks properly and safely. It is essential that, prior to performing any task on this equipment, this individual shall have read and understood the on-product labels, this document and any referenced materials. This in-dividual shall also be familiar with and comply with all applicable industry and governmental standards and regulations pertaining to the task in question.
SAFETY SYMBOLS
The following symbols are used in this document to alert the reader to specific situations:
Indicates a possible hazardous situation which will result in death or serious injury if proper care is not taken.
Indicates a potentially hazardous situa-tion which will result in possible injuries or damage to equipment if proper care is not taken.
Identifies a hazard which could lead to damage to the machine, damage to other equipment or environmental pollution if proper care is not taken or instructions and are not followed.
Highlights additional information useful to the technician in completing the work being performed properly.
External wiring, unless specified as an optional connection in the manufacturer’s product line, is not to be connected inside the control cabinet. Devices such as relays, switches, transducers and controls and any external wiring must not be installed inside the micro panel. All wiring must be in accordance with Johnson Controls’ published specifications and must be performed only by a qualified electri-cian. Johnson Controls will NOT be responsible for damage or problems resulting from improper connections to the controls or application of improper control signals. Failure to follow this warn-ing will void the manufacturer’s warranty and cause serious damage to property or personal injury.
JOHNSON CONTROLS 3
FORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
MANUAL DESCRIPTION FORM NUMBER
Absorption Chiller/Heat Pump Long Term Storage 50.20-NM11
Long-Term Storage Checklist - Absorption Chiller/Heat Pump 50.20-CL10
Long-Term Storage Requirements - General 50.20-NM10
CHANGEABILITY OF THIS DOCUMENT
In complying with Johnson Controls’ policy for contin-uous product improvement, the information contained in this document is subject to change without notice. Johnson Controls makes no commitment to update or provide current information automatically to the man-ual or product owner.
It is the responsibility of rigging, lifting, and operating/ service personnel to verify the applicability of these documents to the equipment. If there is any question regarding the applicability of these documents, rig-ging, lifting, and operating/service personnel should
verify whether the equipment has been modified and if current literature is available from the owner of the equipment prior to performing any work on the unit.
CHANGE BARSRevisions made to this document are indicated with a line along the left or right hand column in the area the revision was made. These revisions are to technical in-formation and any other changes in spelling, grammar or formatting are not included.
ASSOCIATED LITERATURE
JOHNSON CONTROLS4
FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
NOMENCLATURE
YHAP - C 2000 EXW4S
UNIT York AbsorptionHeat Pump
DRIVING SOURCE NONE: =Steam Driven Single Effect NOMINAL RECOVER
HEAT SOURCE CAPACITY MODEL SERIES NAME
EXE: 255 - 500RTEXW2S: 630 - 900RTEXW4S: 1000-2000RT
DESIGN SYMBOL
JOHNSON CONTROLS 5
FORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
TABLE OF CONTENTS
SECTION 1 – GENERAL HEAT PUMP INFORMATION AND SAFETY ................................................................10Introduction .....................................................................................................................................................10About this Manual ...........................................................................................................................................10Warranty .........................................................................................................................................................10Quality Assurance ......................................................................................................................................... 11Emergency Shutdown .................................................................................................................................... 11
SECTION 2 – PRODUCT DESCRIPTION ..............................................................................................................14Heat Pump Components ................................................................................................................................14Control Panel ..................................................................................................................................................14Two Step Evaporator - Absorber ....................................................................................................................16Solution Heat Exchanger ................................................................................................................................16Generator .......................................................................................................................................................17Condenser ......................................................................................................................................................17Crystallization .................................................................................................................................................17Why Does Crystallization Occur? ...................................................................................................................17
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY .....................................................18Inspection .......................................................................................................................................................19Installation Guidelines ....................................................................................................................................19Hoisting the Machine ......................................................................................................................................20Moving the Machine on Rollers ......................................................................................................................22Jack-Up Procedure .........................................................................................................................................24Indoor and Outdoor Installation ......................................................................................................................26Electrical .........................................................................................................................................................26Precautions for Use ........................................................................................................................................27Leak Testing ...................................................................................................................................................27Electrical Shock Cautions ...............................................................................................................................27Vibration and Isolation Details ........................................................................................................................28Hot and Cold Insulation Procedure ................................................................................................................31
SECTION 4 - TECHNICAL DATA ...........................................................................................................................34Weights and Dimensions ................................................................................................................................34Physical Data .................................................................................................................................................35Noise Emission ...............................................................................................................................................36
SECTION 5 - COMMISSIONING ............................................................................................................................38General Guidelines for Use ............................................................................................................................38Precautions for the Use of Water ...................................................................................................................39Hot Water Outlet Temperature Controller .......................................................................................................40Liquid Level Gauges .......................................................................................................................................40Start the Heat Pump .......................................................................................................................................40Stop the Heat Pump .......................................................................................................................................40Electrical Data ................................................................................................................................................51Upper Communication Specification ..............................................................................................................54Scope of Delivery ...........................................................................................................................................55
JOHNSON CONTROLS6
FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
TABLE OF CONTENTS (CONT'D)
SECTION 6 – OPERATION ....................................................................................................................................62YHAU-C Control Center .................................................................................................................................62Change Numeric Values .................................................................................................................................63Date and Time ................................................................................................................................................63Steam or Steam Drain Valve Control..............................................................................................................75Operation Switch ............................................................................................................................................78Select Language ............................................................................................................................................78
SECTION 7 – MAINTENANCE ...............................................................................................................................80Valve Inspection .............................................................................................................................................80Pump Shut Off Valves (Option) ......................................................................................................................80Air Purge Valves and Drain Valves for Steam, Heat Source Water, and Hot Water .......................................80Purge Valves ..................................................................................................................................................80Start the Heat Pump After It Has Been Stopped for A Long Period ................................................................81Purge Procedure ............................................................................................................................................81Performance Check Method of Vacuum Pump ..............................................................................................82Manual Method to Purge Non-condensable Gas Directly from Absorber with Vacuum Pump .......................84Manual Method to Purge Non-condensable Gas from Purging Tank with Vacuum Pump .............................84Automatic Method to Purge Non-condensable Gas from Purging Tank by Water Jet Purge System ............85Refrigerant Refining Method ..........................................................................................................................88Manual Refrigerant Blowdown and Diluting Method ......................................................................................88Decrystallization Method ................................................................................................................................89Maintenance Items .........................................................................................................................................91Lifespan for Various Parts ..............................................................................................................................94Water Quality Control .....................................................................................................................................95Chemical Water Treatment .............................................................................................................................96Replacement of Water ....................................................................................................................................96Treatment for Long Stoppage of the Absorption Heat-Pump .........................................................................96Chemical Treatment .......................................................................................................................................96Flow Speed In Tubes ......................................................................................................................................96Storage Method of the Heat Pump ...............................................................................................................101Wet Storage Method.....................................................................................................................................101Dry Storage Method .....................................................................................................................................101Precautions Against External Damage .........................................................................................................102
SECTION 8 – TROUBLESHOOTING ...................................................................................................................108Troubleshooting Performance Issues ........................................................................................................... 111Vacuum Pump .............................................................................................................................................. 112Water Jet Purge System ............................................................................................................................... 112Abnormal Solution and Refrigerant Levels ................................................................................................... 113Low Vacuum Levels...................................................................................................................................... 113Actions to Take Against Power Failure ......................................................................................................... 115
SECTION 9 - DECOMMISSIONING, DISMANTLING, AND DISPOSAL ............................................................. 116
APPENDIX - MSDS ............................................................................................................................................... 118
JOHNSON CONTROLS 7
FORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
LIST OF FIGURESFIGURE 1 - Components ........................................................................................................................................14FIGURE 2 - Single Effect Steam Absorption Heat Pump Cycle Diagram ................................................................15FIGURE 3 - Warning ...............................................................................................................................................18FIGURE 4 - Hoisting Procedures (Models C255-500EXE) ....................................................................................20FIGURE 5 - Hoisting Procedures (Models C630EXW2S-2000EXW4S) .................................................................21FIGURE 6 - Moving the Machine on Rollers (Models C255-500EXE) ....................................................................22FIGURE 7 - Moving the Machine on Rollers (Models C630EXW2S-2000EXW4S) ................................................22FIGURE 8 - Moving the Machine on TirRollers (Models C255-500EXE) ................................................................23FIGURE 9 - Tir Roller Support .................................................................................................................................23FIGURE 10 - Moving the Machine on TirRollers (Models C630EXW2S-2000EXW4S) ..........................................24FIGURE 11 - Jack-up Procedure (Models C255-500EXE) ......................................................................................24FIGURE 12 - Jack-up Procedure (C630EXW2S-2000EXW4S) ..............................................................................25FIGURE 13 - Jack-up Procedure (Models C255-500EXE)......................................................................................25FIGURE 14 - Jack-up Procedure (Models C630EXW2S-2000EXW4S)..................................................................26FIGURE 15 - Vibration and Isolation Details ...........................................................................................................28FIGURE 16 - Nozzle Locations (Models 630EXW2S- 2000EXW4S) ......................................................................29FIGURE 17 - Nozzle Locations (Models C255-500EXE) ........................................................................................30FIGURE 18 - Hot and Cold Insulation (Single Effect Model - Example ...................................................................32FIGURE 19 - Hot and Cold Insulation (Single Effect Model - Example ...................................................................32FIGURE 20 - Sample Sound Testing .......................................................................................................................36FIGURE 21 - Start Diagram.....................................................................................................................................49FIGURE 22 - Stop Diagram .....................................................................................................................................49FIGURE 23 - Sequential Operation Flowchart ........................................................................................................50FIGURE 24 - Shutdown Absorption Heat Pump Flowchart .....................................................................................50FIGURE 25 - External Connection Terminal Details For CE ...................................................................................51FIGURE 26 - External Connection Terminal Details For GB ...................................................................................52FIGURE 27 - Signal Terminal Transition Wiring ......................................................................................................53FIGURE 28 - Upper Communication System Configuration....................................................................................54FIGURE 29 - Connection for D-Sub 9Pin ................................................................................................................57FIGURE 30 - 2-Wire 1:1 Connection with User-Created Cable...............................................................................59FIGURE 31 - 2-Wire n:1 Connection with User-Created Cable...............................................................................59FIGURE 32 - 4-Wire 1:1 Connection with User-Created Cable...............................................................................60FIGURE 33 - 4-Wire n:1 Connection with User-Created Cable...............................................................................60FIGURE 34 - Main Screen.......................................................................................................................................66FIGURE 35 - Data Screen .......................................................................................................................................68FIGURE 36 - Failure and Alarm History Screen ......................................................................................................70FIGURE 37 - Trend Data Screen.............................................................................................................................71FIGURE 38 - Failure and Alarm Screen ..................................................................................................................72FIGURE 39 - Control Screen ...................................................................................................................................75FIGURE 40 - Control Parameters of 23A and 23B ..................................................................................................77FIGURE 41 - Calculation Details of 23C and 23D ...................................................................................................77FIGURE 42 - Setting Screen ...................................................................................................................................78FIGURE 43 - Location of Manual Valve in Purging System (Example) ...................................................................83FIGURE 44 - Purge Unit ..........................................................................................................................................86FIGURE 45 - Process and Instrumentation Diagram ..............................................................................................87FIGURE 46 - Heat Source Water and Hot Water System .......................................................................................98FIGURE 47 - Steam and Drain System (Open Example) with Steam Drain Control Valve .....................................99FIGURE 48 - Steam and Drain System with Steam Drain Control Valve ................................................................99FIGURE 49 - Duhring Diagram (PTX Chart (°F)) .................................................................................................104FIGURE 50 - Duhring Diagram (PTX Chart (°C)) ..................................................................................................105FIGURE 51 - Specific Gravity - Concentration (°F) ...............................................................................................106FIGURE 52 - Specific Gravity - Concentration (°C) ...............................................................................................107FIGURE 53 - Troubleshooting Sequence Flow Chart............................................................................................ 114FIGURE 54 - Actions to Take Against Power Failure ............................................................................................. 115
JOHNSON CONTROLS8
FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
LIST OF TABLES
TABLE 1 - Nozzle Arrangements (Models 630EXW2S- 2000EXW4S) ...................................................................29TABLE 2 - Nozzle Arrangements (Models C255-500EXE) .....................................................................................30TABLE 3 - Insulating Material and Thickness .........................................................................................................31TABLE 4 - Points Requiring Hot and Cold Insulation ..............................................................................................31TABLE 5 - Weight and Dimensions (Models C255-500EXE) .................................................................................34TABLE 6 - Weight and Dimensions (Models 630 EXW2S - 2000 EXW4S) ............................................................34TABLE 7 - Physical Data (Models 255-500EXE) ....................................................................................................35TABLE 8 - Physical Data (Models 630 EXW2S - 2000 EXW4S) ............................................................................35TABLE 9 - Rotary Pump Rotation ...........................................................................................................................38TABLE 10 - Liquid Level Gauges (Sight Glass) ......................................................................................................40TABLE 11 - Contact Specifications .........................................................................................................................53TABLE 12 - Scope of Delivery ................................................................................................................................55TABLE 13 - Ethernet Interface Specification ...........................................................................................................55TABLE 14 - Communication Specifications ............................................................................................................56TABLE 15 - Read Command ..................................................................................................................................56TABLE 16 - Scope of Delivery of Upper Communication Specification ..................................................................57TABLE 17 - Cable Diagram (RS-422 RS-485) ........................................................................................................58TABLE 18 - Communication Specifications ............................................................................................................61TABLE 19 - Failure List ...........................................................................................................................................73TABLE 20 - Alarm List .............................................................................................................................................74TABLE 21 - Solenoid Valves ...................................................................................................................................80TABLE 22 - Valve Operation Table..........................................................................................................................86TABLE 23 - Maintenance and Inspection ................................................................................................................91TABLE 24 - Lifespan of Common Parts ..................................................................................................................94TABLE 25 - Tendency of Generation of Scales and Corrosion by Quality of Hot and Heat Source Water .............97TABLE 26 - Steam Drain Quality Control ................................................................................................................99TABLE 27 - Heat Source and Hot Water Quality Control (Maximum Concentrations)..........................................100TABLE 28 - Wet Storage Method ..........................................................................................................................102TABLE 29 - Dry Storage Method ..........................................................................................................................103TABLE 30 - Generator High Temperature, Generator High Pressure ...................................................................109TABLE 31 - Refrigerant Overcooled, Source Water Overcooled ..........................................................................109TABLE 32 - Source Water Suspension ................................................................................................................. 110TABLE 33 - Pumps Abnormal ............................................................................................................................... 110TABLE 34 - Troubleshooting Performance Issues ................................................................................................ 111TABLE 35 - Vacuum Pump Troubleshooting ......................................................................................................... 112TABLE 36 - Water Jet Purge Trouble Shooting..................................................................................................... 112TABLE 38 - Low Vacuum Levels ........................................................................................................................... 113TABLE 37 - Abnormal Refrigerant and Solution Levels ........................................................................................ 113
JOHNSON CONTROLS 9
FORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
THIS PAGE INTENTIONALLY LEFT BLANK.
JOHNSON CONTROLS10
SECTION 1 – GENERAL HEAT PUMP INFORMATION AND SAFETY FORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
INTRODUCTIONYORK YHAP-C Absorption heat pumps are manufac-tured to high design and construction standards. High performance, reliability, and adaptability are the result.
This heat pump is used to reclaim waste heat. The re-covered heat can then be used in various ways after the unit is set up. Lower fuel costs and reduced carbon di-oxide emissions are some of the results. See SECTION 7 – MAINTENANCE for more information.
ABOUT THIS MANUALThis manual and any other document supplied with the unit are the property of Johnson Controls which re-serves all rights. This manual may not be reproduced, in whole or in part, without prior written authorization from an authorized Johnson Controls representative.
In addition, this manual:
• Should be read thoroughly before attempting to operate or service the unit.
• Includes suggested best working practices and procedures, which are issued for guidance only. They do not take precedence over the stated in-dividual responsibility or local safety regulations.
• Contains all the information required for correct installation and commissioning of the unit. Op-erating and maintenance instructions are also in-cluded.
• Contains detailed procedures, including installa-tion, commissioning, and maintenance tasks that must only be performed by suitably trained and qualified personnel.
The manufacturer will not be liable for any injury of damage caused by incorrect installation, commission-ing, operation, or maintenance resulting from a failure to follow the procedures and instructions detailed in this manual.
WARRANTYJohnson Controls warrants YHAP-C heat pumps in ac-cordance with the Limited Warranty Engineered Sys-tems Equipment Policy (Form 50.05-NM2).
Johnson Controls warrants all equipment and materi-als against defects in workmanship and materials for a period of 18 months from the date of shipment or 12 months from the date of start-up, whichever comes first, unless labor or extended warranty has been pur-chased as part of the contract.
The warranty is limited to parts only replacement and shipping of any faulty part, or subassembly, which has failed due to defects in workmanship and materials. All claims must be supported by evidence that the fail-ure has occurred within the warranty period, and that the unit was operated within the designed parameters specified.
All warranty claims must specify the unit model, se-rial number, order number, run hours, and starts. Model and serial number information is printed on the unit identification plate.
The unit warranty will be void if any modification to the unit is carried out without prior written approval from Johnson Controls. For warranty purposes, the fol-lowing conditions must be satisfied:
• The initial start of the unit must be carried out by trained personnel from an authorized Johnson Controls Field Service Office.
• Only genuine Johnson Controls approved spare parts, oils, chemicals, and refrigerants must be used.
• All of the scheduled maintenance operations de-tailed in this manual must be performed at the specified times by suitably trained and qualified personnel.
Failure to satisfy any of these conditions will auto-matically void the warranty. Refer to Limited Warranty (Form 50.05-NM2) for complete details.
SECTION 1 – GENERAL HEAT PUMP INFORMATION AND SAFETY
JOHNSON CONTROLS 11
SECTION 1 – GENERAL HEAT PUMP INFORMATION AND SAFETYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
1QUALITY ASSURANCE Units comply with the following directive:
• GB/T 34620-2017 Category I lithium bromide absorption heat pump unit
For Europe:
• CE
• EN ISO 12100:2010
• EN 60204-1 : 2006+A1:2009
• EMC Directive 2014/30 EC
• EN 55011: 2009+A1:2010 (Group 1, Class A)
• EN61000-6-2:2005
• Pressure Equipment Directive 2014/68/EC
For Other Countries:
• Pressure vessel code for GB 150-2011
The unit must be grounded. No installation or mainte-nance work should be done on the electrical equipment without first switching the power off. The power sup-ply must be isolated and locked-off. Servicing and maintenance on live equipment must not be done. No attempt should be made to gain access to the control panel or electrical enclosures during normal operation of the unit.
Components may also have sharp edges. Reasonable care should be taken when working with components to avoid risk of minor abrasions and lacerations.
EMERGENCY SHUTDOWNIn case of emergency, the control panel is fitted with an incoming supply circuit breaker with a red handle. An example is shown below. This can be used an the emergency stop for the unit. Turn the handle counter clockwise to shut down the unit.
LD29113
High Temperature and Pressure Cleaning Do NOT use high temperature and pressure cleaning methods (e.g., steam cleaning) on any part of the pres-sure system. This may cause operation of the pressure relief devices. Detergents and solvents, which may cause corrosion, should also be avoided.
JOHNSON CONTROLS12
SECTION 1 – GENERAL HEAT PUMP INFORMATION AND SAFETY FORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Warning: Rotating object
Caution: Prohibited
Caution: Risk of tumble
Caution: Risk of getting hand caught in
LD20923a
Safety Labels
LD15421c
Warning: Risk of fire.
Warning: Risk of gas poisoning.
For safe operation, read the instructions first.
Warning: This machine may start auto-matically without prior warning.
Warning: Hot surface.
Warning: Safety relief valve may dis-charge gas or liquid without prior warning.
Warning: Isolate all electrical sources of supply before opening or removing the cover, as lethal voltages may exist.
Risk of electric shock
General attention symbol.
Warning: On isolating the supply it may take up to 300 seconds for the capacitor voltage to fall below 50 volts.
Warning: Risk of electrical arc.
JOHNSON CONTROLS 13
SECTION 1 – GENERAL HEAT PUMP INFORMATION AND SAFETYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
1
THIS PAGE INTENTIONALLY LEFT BLANK.
JOHNSON CONTROLS14
SECTION 2 – PRODUCT DESCRIPTION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
LD27818
BC
D
E
A
The principle of an absorption machine is the exchange of heat. In a heat pump, there are four basic heat ex-change surfaces: the evaporator, the absorber, the gen-erator, and the condenser (See Figure 1 on page 14).
Like any heating and cooling system, a heat pump uses evaporation and condensation to remove heat. The ab-sorption cycle uses deionized water as the refrigerant and lithium bromide (LiBr) as the absorbent. The en-tire process occurs in almost a complete vacuum.
HEAT PUMP COMPONENTSThe absorption heat-pump unit consists of the follow-ing components:
• evaporator
• absorber
• condenser
• generator
• solution heat exchangers to heighten the cycle ef-ficiency
• pumps to circulate the refrigerant and solution in the cycle
• purge unit to remove non-condensable gas from the machine
CONTROL PANELThe absorption heat-pump comes with a factory mounted and pre-wired control system. The control panel enclosure is equipped with a hinged access door with lock and key. The control panel includes a touch panel showing all system parameters in various lan-guages with numeric data in metric units. For details of the control panel, see SECTION 6 – OPERATION.
The unit is also equipped with two methods to start and stop operations:
• touch panel
• external signal
SECTION 2 – PRODUCT DESCRIPTION
ITEM COMPONENT NAME
A GeneratorB CondenserC AbsorberD EvaporatorE Heat Exchanger
FIGURE 1 - COMPONENTS
Turn off the power supply by the handle breaker when opening the control panel.
Confirm the main power switch is within 6.56 feet (2 meters) of f the ground. If not, please install the operation platform.
JOHNSON CONTROLS 15
SECTION 2 – PRODUCT DESCRIPTIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
2
S
PG1
PT1
TE2
TE3
TE5
PA
363
SH
1TC
123
AS1
TA1
M
PI
PI
SV
PA
463
SH
2
PA5
63W
H
M
TC2
23A
S2
M
TIC
323
C
TE4
LS
PT2
CAS
-SV
FX1
TIC
123
A
M
LS
FX2
TIC
223
B
CAS
-SV
TA3
26W
H2
PA
663
AP
LD27
829
Che
ck v
alve
Ste
am c
onde
nsat
e ba
ck p
ress
ure
adju
stm
ent v
alve
Dra
in tr
ap
Ste
am
shut
-off
valv
e
Dis
trict
Hea
ting
Wat
er O
utle
t
Ref
riger
ant
pum
p Sol
utio
n ci
rcul
atio
n pu
mp
Sol
utio
n sp
ray
pum
p
Con
dens
er
Ste
am in
let
Ste
am
cond
ensa
teou
tlet
Dis
trict
Hea
ting
Wat
er In
let
Solu
tion
heat
exc
hang
er
sub
cool
er
On-
off v
alve
(S
uppl
y)
On-
off v
alve
(Byp
ass)
Sco
pe o
f sup
ply
Inst
rum
ent
(Inst
alle
d in
the
heat
pum
p)
Con
trol d
evic
e (in
the
PLC
)
Ste
am d
rain
co
ntro
l val
ve
Eva
pora
tor A
bsor
ber
Gen
erat
or
Nee
dle
valv
e
FIGURE 2 - SINGLE EFFECT STEAM ABSORPTION HEAT PUMP CYCLE DIAGRAM
Note: Temperatures and pressures on this graphic are representative. Actual values may differ.
JOHNSON CONTROLS16
SECTION 2 – PRODUCT DESCRIPTION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
HOW IT WORKS
The single effect (steam driven) absorption heat-pump uses deionized water as the refrigerant and lithium bro-mide (LiBr) solution as the absorbent. It is the strong affinity that these two substances have for one another that makes the cycle work.
The vapor pressure of the lithium bromide solution is lower than the vapor pressure of the refrigerant. The vapor pressure of the LiBr solution is directly related to the amount of refrigerant (water) present in the solu-tion with the LiBr and the solution temperature.
TWO STEP EVAPORATOR - ABSORBERThe evaporator and the absorber are split into two sec-tions. This design allows the cycle concentration to be lower than a conventional absorber or evaporator. The lower concentrations means the unit is more reliable and operates with increased efficiency. In addition, it has a lower corrosion potential and uses lower temper-ature steam in the generator.
The heat source water flows through both evaporator sections. It enters the lower evaporator tubes first. It then moves to and through the upper evaporator before it leaves the heat pump.
Each evaporator works at a different temperature and pressure. The refrigerant in the lower evaporator boils at a higher temperature than in the upper one. The waste heat from the heat source water can be extracted in two steps.
The absorber is split into two sections as well. A strong solution enters the top of the upper absorber. It flows down through the upper absorber bundle.
The upper bundle operates at a lower vapor pressure. The lower vapor pressure means that the upper evapo-rator can operate at a lower pressure and temperature.
The solution then flows into the top of the lower ab-sorber section. When the LiBr solution enters the lower absorber section, it is already diluted by the refriger-ant vapor that boiled off in the upper evaporator. Since the lower evaporator is where the first step of the heat source water heat recovery process takes place, the va-por pressure of the solution is enough to maintain the temperature and pressure in the lower evaporator.
The water from the heating load facility enters the low-er absorber section first. This helps to keep the vapor pressure of the weaker solution as low as possible.
LD21213
Evaporator(Upper)
Absorber(Upper)
Evaporator(Lower)
Absorber(Lower)
Low Temp. Heat Source Water Out
Low Temp. Heat Source Water In
LiBr
Hot Water In
SOLUTION HEAT EXCHANGERAs the dilute LiBr solution is sent to the generator, it passes through a solution heat exchanger first. There, the solution is pre-heated before it enters the generator.
The pre-heating reduces the driving heat source re-quirement in the generator. It also helps to cool the concentrated solution before it enters the upper absorb-er section.
LD21214
Low Temp.Heat Exchanger
High TempHeat Exchanger
JOHNSON CONTROLS 17
SECTION 2 – PRODUCT DESCRIPTIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
2
GENERATORThe generator section is a falling film design. The steam passes through the stainless steel tubes. It then heats the pre-heated dilute solution. The pre-heated dilute solution arrives from the high temperature heat exchanger and the steam condensate heat exchanger.
The refrigerant (water) vapors move to the condenser. The LiBr solution left behind is a concentrated (strong) solution. The solution is cooled before it is sent to the upper absorber.
CONDENSERThe refrigerant vapors condense into liquid refrigerant in the condenser section. The hot water aids the pro-cess. The refrigerant water is sent to the lower evapo-rator section through the refrigerant condensate heat exchanger.
LD21215
Condenser
Condensed Refrigerant
CRYSTALLIZATIONAll absorption heat-pumps that use lithium bromide and water as the solution and refrigerant pair are sub-ject to crystallization. This is due to the fact that some areas of the unit operate with solution liquid concentra-tion levels that are only possible at temperatures that are higher than the normal ambient temperature sur-rounding the unit. For example, the solution concentra-tion in the generator of a single effect absorption unit is typically 64.3% lithium bromide by weight. That concentration begins to crystallize at 43.3°C (110°F).
Crystallization happens when the LiBr solution tem-perature drops too low or the concentration is too high. The LiBr solution becomes like slush. At this point, the LiBr solution cannot absorb any more water and will start to solidify (crystallize).
Crystallization occurs in the solution heat exchanger. In addition, it may happen in the generator. It also hap-pens in pipes that are not well insulated and are located in rooms where the temperature can affect the solution as it moves through the pipes.
You can prevent crystallization by making sure you keep the solution temperature high and the solution concentration at the optimum percentage (64%).
Since the solution temperature in the generator is high enough, no crystallization will occur as long as the higher temperature is maintained. Before the unit is shut down, make sure the solution is sufficiently di-luted in all areas of the unit to prevent crystallization during the off cycle. Remember, the solution tempera-ture will eventually become equal to the ambient tem-perature of the room.
All units employ some sort of dilution cycle, which fulfills this requirement. As long as the unit is allowed to dilute itself during an orderly shutdown sequence, the unit should be able to sit idle at fairly low plant room ambient temperatures for extended periods of time without any threat of crystallization. Typically, after a dilution cycle, the average solution concentra-tion within the heat pump will be below 45% lithium bromide by weight. Although the crystallization line on Figure 49 on page 104 or Figure 50 on page 105 does not extend that far, you can see that the solution at a 45% concentration should not crystallize at normal ambient temperatures.
WHY DOES CRYSTALLIZATION OCCUR?The most common reason for crystallization is pow-er failure. If a heat pump is running at full load and power is interrupted for a long time, the concentrated solution in the high side of the unit eventually cools down. Since no dilution cycle was performed, the solu-tion concentration in some areas of the unit will still be high. If the temperature of this concentrated solution is allowed to fall low enough, the solution will reach its crystallization point. Plant room temperature, insula-tion quality and the solution concentration all play a part in the determination of how long it will take before the unit will crystallize. See SECTION 7 – MAINTE-NANCE for information on water quality control and crystallization. The Duhring Diagram (PTX Chart) shows the specific temperatures and pressures of the crystallization area. See Figure 49 on page 104 and Figure 50 on page 105.
JOHNSON CONTROLS18
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY
LD18119
FIGURE 3 - WARNING
Rigging and lifting should only be done by a professional rigger using a written plan. The most appropriate rigging and lifting method will depend on job specific factors, such as the rigging equipment available and site needs. Therefore, a professional rigger must determine the rigging and lifting method to be used. It is beyond the scope of this manual to specify rigging and lifting details.
This heat pump is for air conditioning or a heating manufacturing process. Transport, store, and use this heat pump under the following conditions:
• Installation location: Indoor, Non-explosion area
• Ambient temperature: 10 ~ 40°C
• Humidity: 10 ~ 90% (RH%)
• Altitude: 1000 m or lower
If the temperature in the plant will fall below 10°C, you must have the cold ambient option.
JOHNSON CONTROLS 19
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
3
INSPECTIONThe unit must be inspected prior to customer use by a Johnson Controls Service representative. All damage or possible damage must be reported to the transpor-tation company. For further details, see SECTION 5 - COMMISSIONING.
NOTE: If the unit is shipped as dry ship-ment, the nitrogen gas in the unit will be charged to 0.3barg/4psig on the shell side. The solution and refrigerant water will be in barrels separately.
INSTALLATION GUIDELINESWhen evacuating the nitrogen charge, be sure the area is properly ventilated. Failure to do this could result in suffocation.
When storing the absorption heat pump unit after it has been delivered, note the following potential issues:
1. Problems with machine in storage:
a. Breaking of thin pipes caused by freezing of the refrigerant (water) sealed in the machine and resulting air leak (only in heat pumps that are charged with the solution and refrigerant water)
b. Breaking and air leak due to external damage
c. Deterioration of electrical parts caused by soot and dust
d. Deterioration of electrical parts caused by rainwater (moisture)
e. Rusting of the machine body caused by rain-water (moisture). Air leaks can cause serious damage and are costly repairs. Therefore, use diligence in keeping the machine body free from moisture at all times.
f. Loss of solution or refrigerant water caused by the solution and refrigerant water barrels break-ing.
2. Problems and Preventative Measures
PROBLEM PREVENTATIVE MEASUREFreezing of
refrigerant in machine
Store the machine where the ambient temperature is higher than 0°C. If the
ambient temperature drops below 0°C, use a heater to warm the machine. If a heater is not accessible, the following
options are available to prevent freezing: • Extraction of the refrigerant
• Addition of antifreeze to the refrigerant• Installation of a band heater
For further instruction, contact your nearest authorized Johnson Controls
Service Center. External Damage
Avoid storing the machine in a place which is easily accessible or near a
construction site. If this is unavoidable, use diligence to protect the machine. For further information contact your nearest authorized Johnson Controls Service
Center. Soot & Dust To protect the machine from soot & dust
(or other air particulates) cover the entire machine, including the control panel,
instruments and gauges located on top of the machine with a vinyl sheet. Use
caution not to apply too much pressure to the controls to prevent damage.
Rainwater Avoid storing the machine in areas that are exposed to rainwater or other standing
water.
3. Periodic Inspection and Maintenance
a. Inspect the machine weekly for damage.
b. Check the machine compound gauge daily to verify there is no decline in vacuum and record the vacuum value (-101 to -95kPa). If the vacuum is below the low limit, contact your nearest authorized Johnson Controls Service Center immediately.
c. If the vacuum has dropped as a result of improper machine operation, contact your nearest authorized Johnson Controls Service Center immediately.
NOTE: Use care that foreign matter does not enter the drain valve and air vent valve in the water chamber casing. Keep these valves fully open while the machine is in storage.
JOHNSON CONTROLS20
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
HOISTING THE MACHINEWhen hoisting the machine, attach a shackle to each of the four eye plates and lift the machine using care that the angle formed by the wire is within 60° as shown in the figure below.
Use care not to apply shock to the machine. The ma-chine is a high-vacuum vessel containing a corrosive solution. Use diligence in protecting the machine as repair is labor intensive and costly.
Be sure to lift the machine horizontally. If the machine is inclined, the solution and refrigerant inside will shift producing an offset load. This can cause damage to the machine and pose a risk to the machine installer or per-sons moving the unit.
LD27820
Eye plateC255-500 EXE
FIGURE 4 - HOISTING PROCEDURES (MODELS C255-500EXE)
JOHNSON CONTROLS 21
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
3
LD27821
FIGURE 5 - HOISTING PROCEDURES (MODELS C630EXW2S-2000EXW4S)
JOHNSON CONTROLS22
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
MOVING THE MACHINE ON ROLLERSPlan the entrance of the machine.
Do not incline the machine more than 10°. If the ma-chine has to be inclined more than 10°, the solution and refrigerant will need to be extracted beforehand.
Use care not to apply shock to the machine. The ma-chine is a high-vacuum vessel containing a corrosive solution. Use diligence in protecting the machine as repair is labor intensive and costly.
When a skid base is used to move the machine on roll-ers, secure the skid base and place the machine legs evenly on the skid base before moving the machine on rollers.
LD26819
MAX. MACHINE WIDTH MAX. MACHINE LENGTH
MA
X. M
AC
HIN
E H
EIG
HT
Skid Base
AP
PR
OX
.
APPROX. APPROX.
FIGURE 6 - MOVING THE MACHINE ON ROLLERS (MODELS C255-500EXE)
LD26824
FIGURE 7 - MOVING THE MACHINE ON ROLLERS (MODELS C630EXW2S-2000EXW4S)
JOHNSON CONTROLS 23
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
3
LD26820
LD22925
FIGURE 9 - TIR ROLLER SUPPORT
If using a tir roller to move the machine, fit the tir roller set to each of the four holes shown in the figure below.If using a tir roller to move the machine, fit the tir roller set to each of the four holes shown in the figure below.
FIGURE 8 - MOVING THE MACHINE ON TIRROLLERS (MODELS C255-500EXE)
JOHNSON CONTROLS24
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
LD26825
FIGURE 10 - MOVING THE MACHINE ON TIRROLLERS (MODELS C630EXW2S-2000EXW4S)
JACK-UP PROCEDUREWhen jacking the machine, be sure to fit the jack in each of the jack-up supports as shown below.
FIGURE 11 - JACK-UP PROCEDURE (MODELS C255-500EXE)
LD26821
JOHNSON CONTROLS 25
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
3
LD26826
FIGURE 12 - JACK-UP PROCEDURE (C630EXW2S-2000EXW4S)
Operate the front and rear jacks alternately.
Do not jack up the machine more than about 20 mm at a time. Each time the machine is jacked up, adhere it with a suitable crosstie.
Use the jack-up support on the main shell of the body as shown below. If using a high temperature generator, use secondary jack-up support.
L26822
FIGURE 13 - JACK-UP PROCEDURE (MODELS C255-500EXE)
JOHNSON CONTROLS26
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
INDOOR AND OUTDOOR INSTALLATIONThis heat pump is designed to be used indoors. Expo-sure to the elements can compromise the integrity of the thermal insulation. The minimum allowable tem-perature for outdoor installation is 0°C, provided that the heat pump includes the cold ambient option. Out-door installations will be considered on a case-by-case basis by a Johnson Controls Service Representative.
ELECTRICALThe electrical work must be performed in accordance with the wiring diagrams, delivery specifications, and technical standards for electrical equipment found in SECTION 4 - TECHNICAL DATA. Use the specified cables to complete the wiring. Be sure to fasten them to the terminals securely. Loose fitting cables can cause the terminals to heat up, resulting in fire or electrical shock.
Electrical work must be supervised or completed by a Johnson Controls Service Representative.
A ground fault (earth leakage) circuit breaker is NOT installed on this heat pump. Be sure to install one at the primary side of the unit.
FIGURE 14 - JACK-UP PROCEDURE (MODELS C630EXW2S-2000EXW4S)
STRUCTURAL SUPPORT AND INSTALLATION
Structural support of the unit should be provided for maximum efficiency. Maintain adequate maintenance space around the heat pump. In non-seismic areas, JCI recommends, but does not require foundation bolts to be installed in level concrete to secure the unit and pre-vent shifting.
It is the customer’s responsibility to furnish the founda-tion bolts, nuts and washers when used. Rubber vibra-tion isolator pads must be fitted to the unit base before installation. See Figure 7 on page 25. The tolerance for leveling is 1 inch in 1,000 inches or 1 mm in 1,000 mm, according to the bottom edge of the tube plate.
Waterproof the floor on which the ma-chine is installed in case of leaks.
For the external dimensions of the machine and foun-dation, see the full view of the machine and the foun-dation drawing.
For serviceability and maintenance, leave a minimum of 1,000 mm space on all sides of the heat pump. To be sure there is adequate clearance for tube removal, the space at the end should equal 1.25 x the length of the unit.
LD26827
JOHNSON CONTROLS 27
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
3
PRECAUTIONS FOR USEA caution label for a rotating object is pasted around the belt cover of the vacuum pump. When replacing the oil in the vacuum pump, belt, or performing main-tenance work, stop the heat pump. Be sure to turn off the main circuit breaker (MCB1) and lockout or tagout the unit. If you do not, the vacuum pump could start abruptly and cause injury to you or damage to the unit.
Do not place anything heavy on the machine or its con-trol panel. It may fall and injure someone.
Do not climb up the machine without a safety harness. Contact your local Johnson Controls service office for inspection and maintenance of the machine. Improper inspection and maintenance can not only cause a ma-chine problem but also injure workers.
Keep the hot water, heat source water, and steam under the maximum usage pressure. If they exceed the maxi-mum usage pressure, pipes may spout or leak. That, in turn, may cause an electric shock and a burn.
Do not change the set values of the safety devices and protective devices. Operation with incorrect values can cause problems.
The shut off valve for the pressure release valve must remain open except during servicing. The unit must never be operated with this shut off valve closed.
A caution label for high temperature is pasted at the control panel, solution pump, and vacuum pump. Be sure not to touch the pump during pump operation. It may cause a burn.
Wear protective gloves and goggles when operating the any part of the heat pump.
During service and maintenance work, be sure to turn OFF the main circuit breaker (MCB1) and follow all required lockout or tagout procedures Close the main valve of the steam line. If not, it may cause electric shock and burn.
If the cables of the solution pump, refrigerant pump, or vacuum pump are disconnected for service and main-tenance work, be sure to check the rotating direction of the pump motor. If not, the heat pump may malfunc-tion. When changing the oil in the purge pump, be sure to stop the purge operation.
LEAK TESTINGWhen leak testing, verify the area is properly venti-lated. Failure to do so may result in suffocation.
ELECTRICAL SHOCK CAUTIONSDo not touch the control panel with wet hands. This can cause electric shock. Do not touch the wiring in the control panel.
Other than the control panel and the valves described in the operating manual, do not touch any part of the machine. This can cause a problem and injury.
Apply only the specified source voltage. Application of a different voltage can cause a fire and electric shock.
Welding should only be done in certain circumstances. If welding is done, be careful not to compromise the integrity of the vessel. Prior to welding, be absolutely certain that the electrical system is grounded properly.
Failure to do this can result in electrical shock, injury, or damage to the heat pump.
Do not splash water over the machine and its control panel. This can cause an electric shock.
A warning label for electric shock is pasted at the con-trol panel, solution pump, refrigerant pump, and the terminal box of the vacuum pump motor. Before open-ing the terminal box, be sure to stop the heat pump and turn OFF the main circuit breaker (MCB1).
JOHNSON CONTROLS28
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
VIBRATION AND ISOLATION DETAILSBefore the unit is installed, fit rubber vibration isolators to the unit base. See Figure 13 below for a guide.
Liners may be used to adjust the level of the unit.
LD20193a
200mm
Foundation BoltRubber Vibration Isolator
Sole Plate
Filling with Mortar
WasherNut
Foundation Bolt
Sole Plate
Rubber Vibration Isolator
Nut
Base
Washer
FIGURE 15 - VIBRATION AND ISOLATION DETAILS
JOHNSON CONTROLS 29
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
3
TABLE 1 - NOZZLE ARRANGEMENTS (MODELS 630EXW2S- 2000EXW4S)
YHAP-C
NOZZLE LOCATION
HOT WATER (HW) HEAT SOURCE WATER (HSW) STEAM (STM)
STEAM DRAIN (DRN)
INLET OUTLET INLET OUTLET INLET OUTLET
630EXW2S-2000EXW4S B
ODD PASS
AB
ODD PASS
AB B
EVEN PASS
BEVEN PASS
B
NOTE: These images are representations of possible nozzle arrangements. Refer to the general arrangement drawings in the contract docu-ments. Detailed information on the nozzle locations for each unit can be found there.
LD27822
ITEM DESCRIPTION1 Hot Water Inlet2 Heat Source Water Inlet3 Hot Water Outlet (Even)4 Steam Condensate Outlet5 Steam Inlet6 Heat Source Water Outlet (Odd)7 Heat Source Water Outlet (Even)8 Hot Water Outlet (Odd)
FIGURE 16 - NOZZLE LOCATIONS (MODELS 630EXW2S- 2000EXW4S)
JOHNSON CONTROLS30
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
TABLE 2 - NOZZLE ARRANGEMENTS (MODELS C255-500EXE)
YHAP-C
NOZZLE LOCATION
HOT WATER (HW) HEAT SOURCE WATER (HSW) STEAM (STM)
STEAM DRAIN (DRN)
INLET OUTLET INLET OUTLET INLET OUTLET
C255-500EXE A
ODD pass
E
A
ODD pass
B
A AEVEN pass
AEVEN pass
A
NOTE: These images are representations of possible nozzle arrangements. Refer to the general arrangement drawings in the contract docu-ments. Detailed information on the nozzle locations for each unit can be found there.
LD27823
ITEM DESCRIPTION1 Heat Source Water Outlet (Odd)2 Hot Water Outlet (Odd)3 Hot Water Outlet (Even)4 Heat Source Water Outlet (Even)5 Heat Source Water Inlet6 Hot Water Inlet7 Steam Condensate Outlet8 Steam Inlet
FIGURE 17 - NOZZLE LOCATIONS (MODELS C255-500EXE)
JOHNSON CONTROLS 31
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
3
HOT AND COLD INSULATION PROCEDURE4. The recommended materials and their thickness
for hot insulation and cold insulation are shown in Table 2 below.
5. Use a bonding agent, iron wire, iron band, and so on to fix the hot insulation and cold insulation ma-terials. Never rivet the hot and cold insulation ma-terials. The use of welding pins is not permitted.
6. Make sure the outer covering, flanged parts, and the evaporator, absorber, and condenser water chamber casings can be easily removed for ser-vicing.
TABLE 3 - INSULATING MATERIAL AND THICKNESSHOT INSULATION COLD INSULATION
Material Rock wool or glass wool Polyurethane foam, polystyrene foam, or glass woolThickness 50 mm 50 mm
TABLE 4 - POINTS REQUIRING HOT AND COLD INSULATIONPOINT REQUIRING HOT
INSULATION (1)POINT REQUIRING COLD
INSULATION (1)POINT THAT MUST NOT BE
HEAT-INSULATEDGenerator Evaporator Shell Sight GlassHeat Exchanger for Drain Evaporator Water Chamber Case Valve ManipulatorDrain Piping Refrigerant Spray PipingHeat Exchanger Refrigerant Blow Piping Pressure GaugeAbsorber and Condenser Point Carrying "Cold Insulation" Label Thermometer Insertion HolePoint Carrying "Hot Insulation" Label Relay Insertion Hole
(1) The required type of insulation changes with the actual operating temperature of the unit.(2) There is no need for cold insulation i f the heat source temperature is above 20 °C.
7. The points that require hot insulation and cold in-sulation are shown in Figure 18 on page 32 and Figure 19 on page 32.
8. For the generator, install insulation in a way that makes it easy to remove the front, sides, and rear separately.
9. The required type of insulation changes with the operation temperature of the unit. If the operation temperature is 40°C or higher, apply hot insula-tion. If the operation temperature is 20°C or less, apply cold insulation.
JOHNSON CONTROLS32
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
LD27824
FIGURE 18 - HOT AND COLD INSULATION (SINGLE EFFECT MODEL - EXAMPLE
NOTE: The required type of insulation changes with the actual operating temperature of the unit.
FIGURE 19 - HOT AND COLD INSULATION (SINGLE EFFECT MODEL - EXAMPLE
LD27825
JOHNSON CONTROLS 33
SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLYFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
3
THIS PAGE INTENTIONALLY LEFT BLANK.
JOHNSON CONTROLS34
SECTION 4 - TECHNICAL DATA FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
SECTION 4 - TECHNICAL DATA
This section includes technical information about the unit, such as weights, dimensions and electrical data.
WEIGHTS AND DIMENSIONSThe heat pump will be designed according to the difference of heat source, drive source and hot water temperature of customer. The weights and dimensions will be documented according to the actual heat pump results.
MODEL YHAP-C 255EXE 320EXE 400EXE 500EXE
WEIGHT
OPERATION TON 11.3 13.3 15.5 18.1
MAXIMUM SHIPPING TON 8.5 10.0 11.4 13.8
EMERGENCY WEIGHT TON 19.2 23.2 27.9 33.6
DIMENSION
LENGTH MM 3.6 4.2 5.0 6.0
WIDTH MM 2.5 2.5 2.5 2.5
HEIGHT MM 3.2 3.2 3.2 3.2
TABLE 5 - WEIGHT AND DIMENSIONS (MODELS C255-500EXE)
MODEL YHAP-C 630EXW2S
700 EXW2S
800 EXW2S
900 EXW2S
1000 EXW2S
1120 EXW4S
1250 EXW4S
WEIGHT
OPERATION TON 22.8 24.6 26.5 29.3 31.7 42.4 44.7MAXIMUM SHIPPING TON 16.6 17.7 18.8 21.2 23.1 32.3 34.0
EMERGENCY WEIGHT TON 39.8 43.4 48.0 53.0 58.1 70.9 76.2
DIMENSIONLENGTH MM 5.5 6.0 6.7 7.3 8.0 6.7 7.6WIDTH MM 3.0 3.0 3.0 3.0 3.0 3.6 3.6HEIGHT MM 3.3 3.3 3.3 3.3 3.3 3.9 3.9
MODEL YHAP-C 1400 EXW4S
1500 EXW4S
1600 EXW4S
1680 EXW4S
1800 EXW4S
1900 EXW4S
2000 EXW4S
WEIGHT
OPERATION TON 47.1 49.3 51.5 53.7 56.3 59.1 61.8MAXIMUM SHIPPING TON 35.6 37.2 38.8 40.5 42.5 44.9 47.6
EMERGENCY WEIGHT TON 82.1 86.8 91.5 96.2 101.3 106.5 111.7
DIMENSIONLENGTH MM 8.2 8.7 9.2 9.7 10.2 10.7 11.2WIDTH MM 3.6 3.6 3.6 3.6 3.6 3.6 3.6HEIGHT MM 3.9 3.9 3.9 3.9 3.9 3.9 3.9
TABLE 6 - WEIGHT AND DIMENSIONS (MODELS 630 EXW2S - 2000 EXW4S)
JOHNSON CONTROLS 35
SECTION 4 - TECHNICAL DATAFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
4
PHYSICAL DATAThe heat pump will be designed according to the difference of heat source, drive source and hot water temperature of customer. The physical data will be documented according to the actual heat pump results.
MODEL YHAP-C 255EXE 320EXE 400EXE 500EXE
INSULATIONCOLD M2 12 14 17 20 HOT M2 17 19 22 29
RADIATION HEAT LOSS
WITH INSULATION KW 2.5 3.1 3.9 4.9 WITHOUT INSULATION KW 31.1 39.0 48.8 60.7
WATER VOLUMEHEAT SOURCE WATER M3 0.34 0.39 0.47 0.55
HOT WATER M3 0.88 1.02 1.19 1.35 STEAM M3 0.07 0.09 0.10 0.12
TABLE 7 - PHYSICAL DATA (MODELS 255-500EXE)
MODEL YHAP-C 630 EXW2S
700 EXW2S
800 EXW2S
900 EXW2S
1000 EXW2S
1120 EXW4S
1250 EXW4S
INSULATIONCOLD M2 29 31 33 36 39 44 47 HOT M2 31 33 35 38 41 44 47
RADIATION HEAT LOSS
WITH INSULATION KW 6.0 6.0 7.0 8.0 9.0 10.0 11.0 WITHOUT
INSULATION KW 71.0 79.0 90.0 102.0 113.0 127.0 142.0
WATER VOLUME
HEAT SOURCE WATER M3 1.04 1.12 1.24 1.35 1.47 2.29 2.45
HOT WATER M3 1.77 1.91 2.09 2.25 2.44 3.81 4.08 STEAM M3 0.16 0.18 0.20 0.22 0.24 0.35 0.38
MODEL YHAP-C 1400 EXW4S
1500 EXW4S
1600 EXW4S
1680 EXW4S
1800 EXW4S
1900 EXW4S
2000 EXW4S
INSULATIONCOLD M2 49 52 55 57 60 63 66 HOT M2 49 52 55 57 60 63 66
RADIATION HEAT LOSS
WITH INSULATION KW 13.0 14.0 14.0 15.0 16.0 17.0 18.0 WITHOUT
INSULATION KW 159.0 170.0 181.0 189.0 203.0 214.0 225.0
WATER VOLUME
HEAT SOURCE WATER M3 2.61 2.73 2.85 2.96 3.08 3.20 3.31
HOT WATER M3 4.34 4.57 4.76 4.92 5.11 5.30 5.53 STEAM M3 0.42 0.45 0.47 0.50 0.53 0.55 0.58
TABLE 8 - PHYSICAL DATA (MODELS 630 EXW2S - 2000 EXW4S)
JOHNSON CONTROLS36
SECTION 4 - TECHNICAL DATA FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
FIGURE 20 - SAMPLE SOUND TESTING
LD19976e
1
2
3
4
5
Evaporator Side
A SideB Side(Steam InletSide)
Generator SideBackground Noise
Evaporator Side
A SideB Side(Steam InletSide)
Generator SideBackground Noise
LOCATION* OVERALL OCTAVE BAND
31.5 Hz 63 Hz 125 Hz 250 Hz 500 Hz 1 kHz 2 kHz 4 kHz 8 kHz 16 kHz1 80/83 37/76 48/74 57/73 64/73 69/72 73/73 75/74 75/74 70/71 56/632 77/83 40/79 49/75 56/72 62/71 68/71 70/70 71/70 70/69 70/71 53/603 75/83 41/80 49/75 59/75 62/71 65/68 69/69 71/70 67/66 58/59 44/514 78/84 40/79 50/76 61/77 64/73 71/74 71/71 74/73 71/70 65/66 50/575 64/80 37/76 44/70 60/76 56/65 54/57 57/57 56/55 50/49 36/37 26/33
* Position of Measuring instrumentHeight:1.5 m, Horizontal:1.0 m from heat pump surface
NOTE: These data are reference values. The heat pump unit was not covered with thermal insulation materials and the water pipes (for heat source water, hot water, and steam) were temporary during the measurement.
NOISE EMISSIONThe heat pump may produce an A-weighted emission sound pressure level in excess of 80 dB(A) Normally the A-weighted sound power level is less than 100 dB(A). Hearing protection must be worn at all times when op-erating the heat pump. This hearing protection may im-pact the manner in which operators must communicate to be understood.
JOHNSON CONTROLS 37
SECTION 4 - TECHNICAL DATAFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
4
THIS PAGE INTENTIONALLY LEFT BLANK.
JOHNSON CONTROLS38
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
SECTION 5 - COMMISSIONINGGENERAL GUIDELINES FOR USE
Before OperationCharge the solution and the refrigerant water if the so-lution and refrigerant water is in the barrels during the delivery.
During commissioning, check the motor’s rotating direction of the solution pump, refrigerant pump, and purge pump.
The rotation direction can be quickly tested by using a rotation detector (Bell and Gosset or WILO DKG). If a rotation detector is not available, follow these steps:
The flow of fluid cannot be seen because the solution and refrigerant pumps are hermetically sealed.
1. Remove the plugs at the solution and refrigerant sampling valves.
2. Make sure the valves are completely closed.
3. Confirm that the absorber and the refrigerant tank contain enough solution and refrigerant.
4. Connect a compound gauge (NPT 1/2") to the sampling valve with Teflon tape.
The gauge's scale must be -760 mm Hg. to 2 Kg per cm2g, or -30" Hg. to 30 psig. To prevent corrosion of the gauge, clean it thoroughly and check for leaks after use.
5. Operate the pump and open the valve.
6. Read and record the delivery pressure of the solu-tion pump and the refrigerant pump.
7. Close the valve.
8. Check the pressure readings. See Table 9 on page 38
to see if your pump rotation is in the right direction. The correct direction shows a higher discharge pressure.
The delivery pressure reflects the high vacuum condition of the machine. If the inside pressure is atmospheric, add 1.0 kg per cm (14.3 psig) to the standards in table.
9. Remove the compound gauge.
10. Put the plugs back on the valves.
11. Clean the gauge with water.
12. For the refrigerant, confirm the correct rotation by looking at the refrigerant spray through the sight glass.
TABLE 9 - ROTARY PUMP ROTATIONCORRECTION ROTATION
Solution Circulation Pump
0.10 to 0.20 MPa.G
Solution Spray Pump -0.05 to 0.02 MPa.GRefrigerant Pump -0.08 to -0.02 MPaG
After the completion of the equipment work (installa-tion of the heat pump, thermal insulation for cold or hot surfaces), operate the heat pump and measure the noise around the heat pump unit.
The noise data of the heat pump unit is measured in decibels in the factory. See Figure 20 on page 36.
An Earth Leakage Breaker (ELB) MUST be installed on the unit. If it is not, install it before work continues.
The Heat Pump Pre-Start Up and Commissioning Checklist contains specific information for the instal-lation and start-up of the unit. The steps and proce-dures MUST be performed by a YORK/Johnson Con-trols Service person prior to customer use.
Do not run the solution pump without solution. Do not run the refrigerant pump without refrigerant water.
JOHNSON CONTROLS 39
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
5
All items on the checklist MUST be completed prior to charging and initial operation. Failure to do this may result in injury, machine malfunction, or damage.
PRECAUTIONS FOR THE USE OF WATERStaining and corrosion of the tubes in the evaporator, absorber, generator, and condenser depends on the quality of the water used as district heating (hot) water and heat source water. As a result, water quality must be checked periodically to prevent problems. If wa-ter quality is not controlled and maintained properly, premature tube failure can result. Causes of bad water quality include:
• Polluted seawater
• Brackish water
• Polluted underground water
Be sure to analyze the heat source and district heating (hot) water within one month after commissioning. See Table 27 on page 62.
Install strainers of 10 mesh and above to the heat source water and the hot water inlets.
Shut off valves will be installed at the customer site in the steam, heat source water, and district heating (hot) water inlets and outlets. Be sure the valves are completely open when supplying water. If not, the wa-ter flow can become turbulent (at the shut off valves) and damage the water chamber case and tubes. When you need to temporarily reduce the quantity of the heat source and district heating (hot) water, use the valves to make adjustments.
When the flow rate change of the heat source water is controlled (if the flow rate change function is in-stalled), the load change speed is limited.
• The load change condition to limit the heat source water temperature at the outlet is ±0.5°C: 1.5% minimum / maximum.
• The critical load change condition to prevent an overcooling trip of the heat pump is 5% minimum / maximum.
Set the steam feed pressure at the inlet of the steam manual valve to its specification. If the pressure is low-er than the specification, performance of the heat pump may drop.
Limit the steam pressure fluctuation to between +0.05 and -0.1 MPa. If the pressure fluctuates too much, con-trol becomes unstable. The valve may start to hunt for the correct district heating (hot) water and heat source water temperature at the outlet. As a result, perfor-mance suffers, and the operation may stop.
Be sure to install a 60 to 70 mesh strainer in front of the steam control valve or steam shut-off valve (option). If the valve gets clogged, the steam flow rate cannot be controlled. If the system has the any of the following, then it is vulnerable to steam leaks when the heat pump stops.
• A non-leak steam control valve or steam conden-sate (drain) control valve is not used
• No steam shut-off valve
• A clogged control valve
Crystallization of the solution in the generator may take place.
Adjust the pressure at the steam drain outlet to the specification point. Use the regulator valve on the fa-cility side to make the adjustment.
If the steam drain or air may flow back while the heat pump is stopped, install a check valve in the middle of the drain return piping. (If two or more heat pumps are installed and the drain return pipes are joined to return the drain to the hot well tank, install the check valve before the junction of the pipes.)
Install a drain trap at the lowest place of the steam con-trol valve or steam shut-off valve inlet side to prevent an inflow of drain material to the generator. And, in-stall a mist separator to minimize mist contained in the steam.
A drain trap does not need to be installed in the steam drain line between the heat pump and the hot well tank. The presence of a drain trap will cause the steam flow to become unstable. In this case, the condensed water draining from the heat pump is sub-cooled enough so that a drain trap is unnecessary.
Isolate the main steam supply valve when servicing the heat pump or during an extended shut down.
JOHNSON CONTROLS40
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
HOT WATER OUTLET TEMPERATURE CONTROLLERThe district heating (hot) water outlet temperature con-troller (23A) is located on the sequencer. It controls the district heating (hot) water outlet temperature.
LIQUID LEVEL GAUGESLiquid level gauges are used to check the condition of the heat pump components.
TABLE 10 - LIQUID LEVEL GAUGES (SIGHT GLASS)
LIQUID LEVEL GAUGE NAME SYMBOL FUNCTION
Refrigerant overflow monitoring level gauge
G1Checks refrigerant overflow level
Refrigerant tank level gauge
G2Checks lower limit of refrigerant tank level
Absorber level gauge G3Checks lower limit of absorber
GEN level gauge G4Checks condition of solution in generator
Refrigerant float box level gauge
G5, G6Checks condition of refrigerant in the refrigerant float
START THE HEAT PUMPBefore starting the heat pump, review the following:
• Check that the refrigerant blow valve (VR1) is closed.
• Check the degree of the vacuum in the machine. Use the pressure gauge of the generator.
• Check the steam inlet pressure.
• Open the steam supply manual valve and steam drain manual valve.
• Check that the Refrigerant Pump Auto button is pressed.
After the review is complete:
1. Press the OPER. button on the Control Panel to start the heat pump. To start the heat pump from a remote location, enter the remote start signal.
When the heat pump starts, the following occurs:
• The solution circulation pump, solution spray pump, and refrigerant pump start.
• The steam control valve or steam drain control valve, steam drain solenoid valve and steam shut-off (option) valve open.
• Tthe steam volume is controlled automatically according to the heating load. The Temperature Control lamp lights.
STOP THE HEAT PUMPTo stop the heat pump, press the STOP button on the Control Panel, or to stop the heat pump from a remote location, enter the remote stop signal.
When the heat pump stops, the following occurs:
1. The steam control valve or steam drain control valve, steam drain solenoid valve delay to stop and the steam shut-off (option) valve close.
2. The dilution operation starts and continues for 15 minutes.
During the dilution operation, the solu-tion circulation pump, solution spray pump, and refrigerant pump operate.
3. Once the dilution operation is complete, the solu-tion circulation pump, solution spray pump, and refrigerant pump stop.
4. Then, the heat source water pump, and district heating (hot) water pump stop.
5. Close the steam supply manual valve and steam drain manual valve.
JOHNSON CONTROLS 41
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
5
JOHNSON CONTROLS 1
The following work must be completed in accordance with installation instructions:
CUSTOMER: ____________________________________
ADDRESS: _____________________________________
PHONE: ________________________________________
JCI TEL NO: _____________________ JCI ORDER NO: __________________ JCI CONTRACT NO: ______________
JOB NAME: ____________________________________
LOCATION: ____________________________________
CUSTOMER ORDER NO: _________________________
HEAT PUMP MODEL NO: ____________________________
The work (as checked below) is in process and will be completed by: _____________ / ____________ / ___________UNIT SERIAL NO: _______________________________
Month Day Year
A. General
1. All major pieces, boxes, and crates have beenreceived and accounted for by a YORK/JohnsonControls Service Representative. ...........................
2. Any damage, or signs of possible damage, havebeen documented to the transportation company ....
3. Unit installed in an area protected from weatherand maintained at a temperature above freezing. ...
4. Vibration-proof rubber sheets are installed betweenthe heat pump base and the site foundation. ...........
5. Unit is located in accordance with minimum clear-ance dimensions. (Required maintenance space isavailable around the machine). ................................
6. Foundation bolts are properly installed. ...................
7. The levelness of the unit is within acceptable range(The tolerance for leveling length and width: 1.0mmfor every 1,000mm). ................................................
8. Generator Compound gauge displays the samepressure reading, or nearly the same reading asprior to shipment. ....................................................
9. Thermal insulation is done according to the specifi-cations detailed in this manual. ................................
10. The following items are NOT covered with insulation:
a. Valves ..................................................................
b. Thermo wells .......................................................
c. Plugs ....................................................................
d. Sight glasses .......................................................
PRE-START UP
CHECKLIST
YHAP-C STEAM SINGLE EFFECT ABSORPTION HEAT PUMP
Supersedes: 155.36-CL1 (1118) Form 155.36-CL1 (319)
HEAT PUMP START UP AND COMMISSIONING CHECKLIST
B. Piping
1. Piping is installed between the unit and the sourceof supply. ..................................................................
2. Steam piping is installed between unit and sourceof supply. .................................................................
3. Heat source water air vent valves and drain valvesare closed. ...............................................................
4. Hot water air vent valves and drain valves areclosed. ......................................................................
5. Loosen the U-band fixing bolt around the steamcondensate heat exchanger. ....................................
6. Close the steam condensate heat exchanger valve.
7. Install the steam condensate heat exchanger plug. .
8. The following and its related equipment are readyfor operation:a. Hot water pump ...................................................
b. Heat source water pump .....................................
9. Detachable flanges are properly installed close to the:a. Heat source water box. .......................................
b. Hot water box ......................................................
c. Steam box ...........................................................
10. A mesh strainer is installed on the:a. Heat source water line .........................................
b. Hot water line .......................................................
c. Steam inlet lines ..................................................
JOHNSON CONTROLS42
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
JOHNSON CONTROLS2
FORM 155.36-CL1 ISSUE DATE:11/28/2018
11. Air piping work is complete, leak tested, andflushed for the following lines:
a. Heat source water ...............................................
b. Hot water .............................................................
c. Steam supply .......................................................
d. Steam drain lines .................................................
12. Clean the mesh strainers on the lines. .....................
13. Steam supply pressure is stable and within accept-able range. ...............................................................
14. The pressure gauge and its siphon tube are installed before the steam control valve......................
15. The steam drain line has the following installed:a. Pressure gauge ...................................................
b. Check valve .........................................................
c. Adjusting valve ....................................................
16. Start the heat source water pump. ...........................
17. Start the hot water pump. .........................................
18. Water box pressure does not exceed maximum pressure for the heat source water and hot watersystems. ...................................................................
19. Flow rate of heat source water and hot water is ad-justed within acceptable range. ................................
20. Steam supply temperature is at its saturation tem-perature or lower. .....................................................
C. Valve and Sensor Check
1. Adjusting valves are set correctly. ...........................
2. The manual valves on the water jet purge line areclosed. .....................................................................
3. Close the manual valves on the purge line to theAbsorber. ..................................................................
4. Close the manual valve to purge (vacuum) pump. ..
5. Detection component of the thermosensor is in-serted into the thermowell according to designrequirements. ..........................................................
D. Electrical
1. The insulation resistance of each motor the MCBsecondary side is within acceptable range. ............
2. Power supply voltage is within acceptable range. ...
3. Control panel wiring is correctly connected to thesteam control valve. ................................................
4. The external control wiring is completed from thecontrol panel to the water pump motor starters, andother related equipment. ..........................................
E. Purge System
1. Unconnected end of the water discharge hose forthe water jet purge is in the drain ditch or drain port.Nothing is directly connected. .................................
2. Add lubrication oil to the vacuum pump. ..................
3. Vacuum pump motor rotation is correct. .................
4. Navigate to the setting screen in the control panel. ..
5.
6.
Press the manual WJ purge OFF button. ................
Press the purge pump OFF button. .........................
NOTES:________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
JOHNSON CONTROLS 43
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
5
JOHNSON CONTROLS 3
FORM 155.36-CL1 ISSUE DATE:11/28/2018
F. Evacuate Nitrogen Charge (if the heat pump ispressurised with N2)
1. Remove the plug in the purge line. .........................
2. Release the nitrogen gas until the generator com-pound gauge indicates approximately 0.005MPa.G. (0.725 PSI). .............................................................
3. Re-install the plug in the purge line. ........................
4. Navigate to the setting screen in the control panel. .
5. Press the purge pump ON button. ...........................
6. Check the oil level in the purge pump. .....................
7. Using the vacuum pump, evacuate the nitrogengas until the Generator Compound gauge indicatesapproximately -0.1MPa.G. (-14.5 PSI) ....................
8. Close all open manual valves. .................................
9. Press the purge pump OFF button. .........................
10. Turn the power switch (MCB) off. .............................
11. Replace or add oil to the purge pump. .....................
G. Solution and Refrigerant Charge (if the heat pump is shipped dry)
1. Purge the vacuum until the Generator com-pound gauge indicates approximately -0.1 MPaG (-14.5PSIG) .............................................................
2. Charge the solution from the absorber solutionsampling valve ........................................................
3. Charge the refrigerant water through the refrigerantwater sampling valve. ..............................................
H. Panel Checks
1. Thermal relays conform to the factory inspectionsheet. ......................................................................
NOTES:________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
2. Interlock and answerback signal(s) for the follow-ing are available:
a. Hot water pump ...................................................
b. Heat source water pump .....................................
3. Indicators on the control panel are correct....
4. The temperature setting parameters for capac-ity control are correct.............................................
5. Date and time reflect local time zone.....................
6. The rotation direction is correct for the following:
a. Solution circulation pump ....................................
b. Solution spray pump ............................................
c. Refrigerant pump .................................................
7. The water flow suspension switch works properly....
START UP CHECKLIST
A. Operation Check
1. Manually start the heat source water pump and thehot water pump. .......................................................
2. Confirm water box covers do not leak during waterpump operation. ......................................................
3. Stop the heat source water pump and the hot waterpump manually. ........................................................
4. Press the Auto button for each water pump. ..........
5. Open the refrigerant manual blow valve. .................
6. Navigate to the control screen in the control panel. .
7. Press the steam, or steam drain, valve MANUALbutton. ......................................................................
8. Navigate to the setting screen in the ControlPanel. .......................................................................
JOHNSON CONTROLS44
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
JOHNSON CONTROLS4
FORM 155.36-CL1 ISSUE DATE:11/28/2018
9. Make sure that the refrigerant pump AUTO buttonis pressed. ................................................................
10. Check that the steam control valve or steam draincontrol valve is closed. .............................................
11. Press the OPER. button. ..........................................
12. Check that the following start properly::
a. Solution circulation pump ....................................
b. Solution spray pump ............................................
c. Refrigerant pump .................................................
13. Check for abnormal noise and/or vibration. .............
14. Open the manual valves on the water jet purgeline. ..........................................................................
15. Navigate to the setting screen in the control panel..........
16. Press the manual WJ purge MANUAL button. ..........
17.
panel. .......................................................................
19. Press the manual WJ purge AUTO button. ................
20. Navigate to the control screen in the Control Panel.......
the procedure. ..........................................................22. Press the steam control valve or steam drain con-
trol valve AUTO button. ...........................................23. Check that the steam control valve or steam
drain control valve works automatically accord-ing to the hot water and heat source water outlettemperature. .............................................................
24. The stream drain back pressure meets the requirements of the factory inspection sheet. If not, adjust the pressure...................................................
25. Press the STOP button on the control panel.............
26. Check that the dilution process is complete. ............
27. Navigate to the setting screen. ...........................
28. Press the purge pump ON button. ...........................
29. Purge non-condensable gas from the absorber.Use the procedure detailed in SECTION 7 - MAIN-TENANCE of the manual. .......................................
30. Purge non-condensable gas from the purge tank.Use the procedure detailed in SECTION 7 - MAIN-TENANCE of the manual. .......................................
31. Press the purge pump OFF button. .........................
32. Press the OPER. button on the control panel. .........
33. Operate the heat pump for 3 hours or longer. ..........
34. Close the manual blow valve for the refrigerant. ......
35. Operate the heat pump for an additional hour (orlonger). .....................................................................
36. Check that the specific gravity of the refrigerant iswithin the acceptable range. ....................................
37. Check that the heat source water outlet temperature is lower than the heat source water inlet temperature.
38. Record the running data on data sheets. ................
39. Open the refrigerant return maintenance valve toreturn the refrigerant from the mist separator to theevaporator. ..............................................................
40. Close the refrigerant return maintenance valve. ......
41. Stop the heat pump. .................................................
NOTES:________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
________________________________________________________________
Check that the water jet purge system works and water is discharged from the water discharge hose.
Navigate to the operation screen in the control18.
Gradually increase the setting value in the Manual Input field. Refer to Change Numeric Values in 155.36-ICOM1.EN.CE.GB for more information on
21.
JOHNSON CONTROLS 45
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
5
JOHNSON CONTROLS 5
FORM 155.36-CL1 ISSUE DATE:11/28/2018
B. Purge System Check
1. Press the purge pump OFF button. .........................
2. Close the manual valves to the absorber. ................
3. Close the manual valves on the purge line to thepurge tank. ...............................................................
4. Check that all the manual valves on the water jetpurge line are open. .................................................
5. Make sure that the purge pump OFF button ispressed. ...................................................................
6. Make sure that the manual WJ purge AUTO buttonis pressed. ................................................................
7. Press the STOP button. ...........................................
8. Turn the power switch (MCB) off. .............................
9. Change the oil in the purge pump. ...........................
10. Turn the power switch (MCB) on. .............................
11. Slightly open the ballast valve of the vacuum pump.
C. Remote Operation Check
Make sure the heat pump starts/stops via remote con-trol. ...............................................................................
D. Operation instruction
Review the operation and maintenance instructions inthe manual with the customer. ......................................
Customer Signature: ______________________________________________
Title: _________________________________________
Form Completed by: ________________________________________________
Customer Names:
1. __________________________________
2. __________________________________
3. __________________________________
: _________ / _________ / _________Month Day Year
JOHNSON CONTROLS46
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
JOHNSON CONTROLS6
FORM 155.36-CL1 ISSUE DATE:11/28/2018
STEAM SINGLE EFFECT ABSORPTION HEAT PUMP COMMISSIONING DATA SHEET (1/2) User:Model: YHAP MFG. No.: User's machine code:
Insulation Resistance Electric Power SupplyStandard: 5 MΩ or more (with 500V megger) R-Gnd S-Gnd T-Gnd Specification: AC V /
HzCircuit breaker MΩ Standard: Within +/- 10% of spec.
R-S VU-Gnd V-Gnd W-Gnd R-T V
Solution circulation pump MΩ S-T VSolution spray pump MΩ R-Gnd VRefrigerant pump MΩ S-Gnd VPurge pump MΩ T-Gnd V
Thermal Relay Setting Refrigerant Purity Temperature SettingSolution circulation pump A Standard: 1.040 (kg/L) or less Hot water outlet (23A)Solution spray pump A Specific gravity Setting value °CRefrigerant pump A Turbidity Prop. band %Purge pump A Integ. time sec.
Heat Source Water Outlet (23B)Pump Discharge Pressure Setting value °CSolution circulation pump MPa.G Prop. band %Solution spray pump MPa.G Integ. time sec.Refrigerant pump MPa.G Heat Water ABS Outlet (23C)
Setting value °CProp. band %Integ. time sec.
Heat Water ABS Outlet (23D)Setting value °CProp. band %Integ. time sec.
JOHNSON CONTROLS 47
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
5
JOHNSON CONTROLS 7
FORM 155.36-CL1 ISSUE DATE:11/28/2018
STEAM SINGLE EFFECT ABSORPTION HEAT PUMP COMMISSIONING DATA SHEET (2/2)User:Model: YHAP MFG. No.: User's machine code:Running DataDate: Measured by Specification Standard : : :
Steam
Steam control valve or steam drain control valve position
% Control panel
Steam primary pressure Pressure gauge ≤ 0.8MPa.GSteam secondary pres-sure
Pressure gauge
Steam temperature °C Thermometer ≤175°CDrain outlet (back) pressure
Pressure gauge
Drain temperature °C Thermometer ≤ 95°CSteam consumption Flow meter
Hot Water
Inlet temperature °C Control panelOutlet temperaturefrom absorber °C Control panel
Inlet pressure Pressure gaugeOutlet pressure Pressure gauge[3] Pressure drop DPG or calculation [4][1] Flow rate FM or calculation [2]
Heat Source Water
Inlet temperature °C Control panelOutlet temperature °C Control panelInlet pressure Pressure gaugeOutlet pressure Pressure gauge[7] Pressure drop DPG or calculation [8][5] Flow rate FM or calculation [6]
Absorption Cycle
Generator press.(Gauge)
MPa.G Compound gauge ≤ -0.003MPa
Generator press. (Sen-sor)
kPa.abs
Control panel ≤ 94.7kPa
Generator temperature °C Control panel ≤165°CGenerator concentration
% Control panel
Refrigerant temperature °C Control panel
Outlet temperature °C Control panel
JOHNSON CONTROLS48
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
FORM 155.36-CL1 ISSUE DATE:11/28/2018
Liquid Level
Generator Level gaugeAbsorber Level gaugeEvaporator (Lower) Level gaugeEvaporator (Upper) Level gaugeRef. Float Box (Upper) Level gaugeRef. Float Box (Lower) Level gauge
NOTES:Operating hours hoursNumber of purge times timesFill out each specification pressure drop according to the factory inspection report (actual value). If differential pressure gauge (DPG) is not available, calculate each pressure drop.If flow meter (FM) is not available, calculate each flow rate as below.
[1] = [2] x √[3]/[4] [5]=[6] x √[7]/[8]
LD20020
Same Height
Waterbox
OUT
P P
IN
JOHNSON CONTROLS 49
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
5
1
1
Remote or local Operation
Change
Power On
Initialize Self-Check Mechanism
Heat Source Water and Hot Water Pump
Interlock Start
Heat Source Water and Hot Water Pump Interlock
Established
Solution Pump and Refrigerant Pump Start
Steam control valve or steam drain control valve open,
steam drain solenoid valve open and steam shut off valve
open (option)
Local Start Operation Remote Start Operation
Defective Signal Output
Remote
Local
No3 minutes
Yes
Temperature Control Running
FIGURE 21 - START DIAGRAM FIGURE 22 - STOP DIAGRAM
Stop Operation
Dilution Time Count
Dilution Time Increasing
Heat Source Water or Refrigerant Supercooling
Yes
Dilution Time Up
No
GeneratorPressure Low
No
Dilution Operation More Than 30 mins
No No
Yes
Yes
Solution Pump or Refrigerant Pump
Stop
Heat Source Water and Hot Water
Pump Stop
Absorption Heat Pump Stops
Dilution Time Stops Increasing
Solution Pump or Refrigerant
Pump Stop
Solution Pump or Refrigerant Pump Continue Running
Steam control valve or steam drain control valve
close, steam drain solenoid valve delay to close and
steam shut off valve close (option)
Yes
JOHNSON CONTROLS50
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Hea
t Pum
pHeat Source Water
Pump
Sequential Operation
AND Hot Water Pump
Sequential Operation
ANDInterlock (2)
Sequential Operation
Interlock
Other interlocks, including earthquake sensor, abnormal room temperature sensor, etc
NOTES: 1. Implement sequential operation of the heat source water pump and the hot water pump from the heat pump.2. Implement sequential operation in such a way that when the heat source water pump stops, the hot water stops too.3. If the heat sourced water and hot water system is the common system, it is required to install the isolation valve on the heat source water and hot water inlet pipe leading to the heat pump, and interlock these isolation valves with the heat pump control panel. It is imperative for safe and reliable operation of the heat pump and to prevent potential crystallization of lithium bromide solution and freezing of the evaportor tubes.
FIGURE 23 - SEQUENTIAL OPERATION FLOWCHART
FIGURE 24 - SHUTDOWN ABSORPTION HEAT PUMP FLOWCHART
Stop heat pump locally or from remote site
AND
Heat pump dilution operation
begins
Heat pump dilution operation completed
Stop the heating load system
Completed
H e a t p u m p , h e a t source water, hot water
pump stop
Not completed
Note: Close the steam inlet manual valve once the unit has stopped.
JOHNSON CONTROLS 51
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
5
ELECTRICAL DATAThe heat pump will be designed according to the dif-ference of heat source, drive source and hot water tem-perature of customer. The electrical data will be docu-mented according to the actual heat pump results.
LD28597
Power supply
TB4 Terminal Block
Control valve (4 - 20 mA)
Power supply
District heating water bypass valve open signal
District heating water supply valve open signal
District heating water pump operating signal
Hot source water pump operating signal
Common
Operation signal
Failure signal
Alarm signal
Dilution signal
Remote signal
TB3 Terminal Block
TB1 Terminal Block
Absorption heat pump control panel(scope of supply)
Ancillary equipment board (out of scope of supply)
Power supply3-phase, 3-wire
(See the speciication sheetfor voltage and frequency)
CommonPotential-free level start
Potential-free level stop
Common
Operation signal
Failure signal
Alarm signal
Dilution signal
Remote signal
Hot source water pump operating signal
District heating water pump operating signal
District heating water supply valve open signal
District heating water bypass valve open signal
Heat source water pump interlock
District heating water pump interlock
District heating water supply valve close limit
District heating water bypass valve open limit
Steam shut off valve (option)
Steam control valve
FIGURE 25 - EXTERNAL CONNECTION TERMINAL DETAILS FOR CE
JOHNSON CONTROLS52
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
LD28598
Power supply
TB4 Terminal Block
Control valve (4 - 20 mA)
Power supply
District heating water bypass valve open signal
District heating water supply valve open signal
District heating water pump operating signal
Hot source water pump operating signal
Common
Operation signal
Failure signal
Alarm signal
Dilution signal
Remote signal
TB3 Terminal Block
TB1 Terminal Block
Absorption heat pump control panel(scope of supply)
Ancillary equipment board (out of scope of supply)
Power supply3-phase, 4-wire
(See the speciication sheetfor voltage and frequency)
Common
Potential-free level start
Potential-free level stop
Common
Operation signalFailure signal
Alarm signal
Dilution signal
Remote signal
Hot source water pump operating signal
District heating water pump operating signal
District heating water supply valve open signal
District heating water bypass valve open signal
Heat source water pump interlock
District heating water pump interlock
District heating water supply valve close limit
District heating water bypass valve open limit
Steam shut off valve (option)
Steam/steam drain control valve
FIGURE 26 - EXTERNAL CONNECTION TERMINAL DETAILS FOR GB
JOHNSON CONTROLS 53
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
TABLE 11 - CONTACT SPECIFICATIONS
ABSORPTION HEAT PUMP CONTROL PANEL-> EXTERNAL INPUT TERMINAL
DIGITAL SIGNAL MAX START & STOP VOLTAGE: AC250 V / DC125 VMAX. START & STOP CURRENT: 1 A 1 POINT (RESISTANCE LOAD)
EXTERNAL OUTPUT TERMINAL-> ABSORPTION HEAT PUMP CONTROL PANEL
DIGITAL SIGNAL RATED VOLTAGE CURRENT: DC24 V / 7 mA or no voltageANALOG SIGNAL
HOT WATER OUTLET TEMPERATURE REMOTE SIGNAL4 mA: STANDARD TEMPERATURE 20mA: STANDARD TEMPERATURE + REMOTE SETTING DIFFERENTIAL
LD22032
Example: Transion wiring in case of startingpanel of source water pump and hot water pumpare separately equppied.
Test Start Stop
Interlock
Test
Start Stop
Interlock
Starting Panel for Hot Water Pump
Starting Panel for Source Water Pump Steam Absorption Heat PumpControl Panel
Source Water Pump Start Signal
Hot Water Pump Start Signal
FIGURE 27 - SIGNAL TERMINAL TRANSITION WIRING
Example: Transition wiring in case of starting panel of source water pump and hot water pump are separately equipped.
JOHNSON CONTROLS54
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
UPPER COMMUNICATION SPECIFICATIONThe information in this section applies to the C series steam heat pumps.
Upper Communication System ConfigurationThe configuration of the upper communication system is shown in Figure 10 below.
LD27828
Central Monitoring Unit
Scope of Delivery by Customer
Scope of Delivery byJohnson Controls
Data Concentrator (HUB)
FIGURE 28 - UPPER COMMUNICATION SYSTEM CONFIGURATION
JOHNSON CONTROLS 55
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
SCOPE OF DELIVERYJohnson Controls scope of delivery for the upper com-munication system covers the control panels for the upper communication function. The customer is re-sponsible to deliver all other related equipment: con-centrator (HUB), installation, wiring, communication program for the central monitoring unit, etc. See Fig-ure 28 on page 54.
TABLE 12 - SCOPE OF DELIVERYITEM CUSTOMER JCI REMARKS
Control panel with upper communication
function
X Communication protocol: Modbus TCP
Data concentrator (HUB)
X Installation and wiring are included
Wiring work for Ethernet connection
X Apply twisted pair cable
Communication program for central
monitoring unit
X See Table 11 on page 53 and Table 14 on page 56 for the details of the IP address, function code, communication data address, etc.
Connection Port for Ethernet CommunicationMake sure that the Ethernet cable is plugged into the correct port on the Control Panel. The Ethernet con-nection port is located at the bottom left on the back of the Control Panel.
TABLE 13 - ETHERNET INTERFACE SPECIFICATION
ITEM SPECIFICATIONCommunication format 10BASE-T 100BASE-TXConnector shape RJ-45 type modular jack connectorLED function Active
(Green)Blink Data sending or receiving
No light No data sending or receivingLink
(Green)Blink Data sending or receiving via
10BASE-T100BASE-TXNo light No connection or successor job
failure
JOHNSON CONTROLS56
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Communication Specification
TABLE 14 - COMMUNICATION SPECIFICATIONSCommunication Protocol Modbus TCP
Communication Path Type 10BASE-T 100BASE-TXIP Address (No. 1) 192.168.1.1, (No.2) 192.168.1.2, (No. 3) 192.168.1.3
Subnet Mask 255.255.255.0Function Code Read Command
(Digital Signal) 0.1 Read Coil (Analog Signal) 0.3 Read Holding RegisterWrite Command (Digital Signal) 0.5 Force Single Coil
Communication Data
TABLE 15 - READ COMMANDITEM DISPLAY UNIT ADDRESS CONTENT
SE
T VA
LUE
1 Set Point 65.0 °C 00001 0050~1000 unit, 1 unit=0.1°C2 Automatic stop temp. (thermo-off
temp)70.0 °C 00003 0040~1000 unit, 1 unit=0.1°C
3 Temp. difference of Automatic start or stop control
5.0 °C 00005 0001~1000 unit, 1 unit=0.1°C
OP
ER
ATIO
N C
ON
DIT
ION
4 Operation condition 0 or 1 - 00021 0:STOP, 1:OPERATION5 Local or remote mode condition 0 or 1 - 01001 0:LOCAL, 1:REMOTE6 Solution pump condition 0 or 1 - 01003 0:STOP, 1:OPERATION7 Refrigerant pump condition 0 or 1 - 01005 0:STOP, 1:OPERATION8 Control manipulated variable 100 % 00023 -0100~1100 unit, 1 unit=0.1%9 Failure signal 0 or 1 - 01011 0:NORMAL OPERATION
1:FAILURE OCCUR10 Alarm signal 0 or 1 - 01013 0:NORMAL OPERATION
1:ALARM OCCUR
ME
AS
UR
EM
EN
T VA
LUE
11 Heat source water inlet temp. 25.0 °C 00083 0001~4000 unit, 1 unit=0.1°C12 Heat source water outlet temp. 15.0 °C 00085 0001~4000 unit, 1 unit=0.1°C13 Refrigerant temp at evaporator 15.0 °C 00087 0001~4000 unit, 1 unit=0.1°C14 Hot water inlet temp. 40.0 °C 00089 0001~4000 unit, 1 unit=0.1°C15 Hot water outlet temp. 65.0 °C 00091 0001~4000 unit, 1 unit=0.1°C16 Generator solution temp. 100.0 °C 00095 0001~4000 unit, 1 unit=0.1°C17 Generator pressure 50.0 kPa 00101 0001~1100 unit, 1 unit=0.1 kPa18 Purge tank pressure 2.0 kPa 00103 0001~4000 unit, 1 unit=0.1 kPa
JOHNSON CONTROLS 57
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
User CreatedThe diagrams and tables that follow detail some of the work that must be performed by the customer to be sure that the communication systems work properly.
LD20597
Serial Interface (COM2) Connect User-Created Cable
LD20597a
FIGURE 29 - CONNECTION FOR D-SUB 9PIN
TABLE 16 - SCOPE OF DELIVERY OF UPPER COMMUNICATION SPECIFICATION
ITEM CUSTOMER JCI REMARKSControl panel with upper communication function
X Communication protocol: Modbus RTU
Wiring work for Modbus RTU communication
X Apply RS485 communication cable. See Table 17 on page 58 for more information
Communication program for central monitoring unit
X See Table 18 on page 61 for the details of the communication protocol, the path type, function
code, communication data address, etc.
JOHNSON CONTROLS58
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
TABLE 17 - CABLE DIAGRAM (RS-422 RS-485)PIN CONNECTION PIN.
NO.RS-422 RS-485
5
1
9
6
LD20598
SIGNAL NAME DIRECTION MEANING1 RDA Input Receive Data A (+)2 RDB Input Receive Data B (-)3 SDA Output Send Data A (+)4 ERA Output Data Terminal Ready A (+)5 SG Signal Ground6 CSB Input Send Possible B (-)7 SDB Output Send Data B (-)8 CSA Input Send Possible A (+)9 ERB Output Data Terminal Ready B (-)Shell FG Frame Ground (Common with SG)
Interfit bracket is $4-40 (UNC)
JOHNSON CONTROLS 59
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
2 Wire Cable Diagrams Without AdaptorThe following are sample cable diagrams for a 2-wire type connection.
LD21546FIGURE 30 - 2-WIRE 1:1 CONNECTION WITH USER-CREATED CABLE
LD21547
FIGURE 31 - 2-WIRE N:1 CONNECTION WITH USER-CREATED CABLE
JOHNSON CONTROLS60
SECTION 5 - COMMISSIONING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
4 Wire Type Cable Diagrams Without AdaptorThe following are sample cable diagrams for 4-wire type connections.
LD21548
FIGURE 32 - 4-WIRE 1:1 CONNECTION WITH USER-CREATED CABLE
LD21549FIGURE 33 - 4-WIRE N:1 CONNECTION WITH USER-CREATED CABLE
JOHNSON CONTROLS 61
SECTION 5 - COMMISSIONINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
The next table contains information about the commu-nication specifications needed for the Modbus RTU. See Table 15 on page 56 for information about the Read Command.
TABLE 18 - COMMUNICATION SPECIFICATIONSCommunication Protocol Modbus RTUCommunication path type RS422 RS485 Data Length: 8 Bit Stop Bit: 1 Bit Parity: EVEN Speed: 9600 bps
Connector D-Sub 9pinFunction Code Read Coil Status:01 Read Holding Register:03
Device Digital Signal: Coil Analog Signal: Holding RegisterSlave Equipment Address 1
JOHNSON CONTROLS62
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
SECTION 6 – OPERATION
YHAU-C CONTROL CENTERThe YHAU-C Control Center, furnished as standard on each heat pump, allows for efficiency, monitoring, data recording, heat pump protection, and operating ease. The Control Center is factory-mounted, wired, and tested. It used as a control system for lithium bromide absorption heat-pumps.
The panel is configured with a color TFT Display with buttons that are integrated into the display. A single button reveals a wide array of information on a large, full-color illustration of the appropriate component. In-formation is easier to interpret.
The LCD display allows for a graphic animated display of the heat pump, its sub-systems and system param-eters. In addition, you may view the historical opera-tion of the heat pump as well as the present operation.
Data can be displayed in Metric units plus keypad en-try of set points to 0.1 increments.
LD29091
Security access using passwords is provided to prevent unauthorized changes of set points. There are two lev-els of access. Each level has its own password. There are certain screens, displayed values, programmable set points, and manual controls not shown that are used for servicing the heat pump.
COMMON ITEMSButtons are listed in the order they are seen on the screen: left to right and top to bottom.
The Control Center screens have items that are applica-ble to each feature of the Control Center. This includes the following common items:
• LOCAL and REMOTE: Buttons that allow you to switch the operating location between remote and local. The setting can be changed while the unit is operating. Press and hold the appropriate button for 2 seconds to make the change.
• Operating Status: The display appears at the center of the screen. It shows the following op-erating conditions: Stop, Operating, and Failure Activating.
• Failure and Alarm: Warning lamps that light if the unit has a failure or a warning alarm.
• Date and Time: Shown on the upper right corner of each screen.
• OPER. and STOP: Buttons in the lower left cor-ner to allow you to stop or start the unit.
When you press the OPER. button while the unit is stopped, or STOP while the unit is operating, a confir-mation message appears. Press YES or NO depending on whether you want to continue or cancel your selec-tion.
LD29092
JOHNSON CONTROLS 63
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
• Screen Name Buttons: Located along the bottom of the screen. These are used to change screens. The selected button lights when it is active.
CHANGE NUMERIC VALUESMany numeric values, such as the set point and the ranges on the Trend screen, can be changed.
LD29093
Here is how:
1. Touch the number to be changed. A numeric key-pad appears.
2. Enter the new value on the keypad.
3. Press the ENT button to set it.
DATE AND TIMETo set the date and time, use the following procedure. You can do this from any screen. We are showing you how to do the procedure starting at the MAIN screen.
1. Press the STOP button on the MAIN screen to stop the heat pump. It can not be operating while this procedure is being performed.
2. Press the upper left corner of the screen.
3. Press the lower right corner of the screen within 0.5 seconds
4. The system menu bar displays along the bottom of the screen.
At this time, the system menu bar is avail-able only in Japanese.
5. Press the Offline button.
6. Tap the Password field on the screen that displays. The numeric keypad displays.
For information on how to use the keypad, see the Change Numeric Values section on the previous page.
LD29094
LD29095
JOHNSON CONTROLS64
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
LD21987LD21987
7. Enter the password.
8. Press the ENT key..After you complete the pass-word entry, the Offline Mode screen displays.
9. Tap the drop-down arrow to the right of the entry in the OFFLINE LANGUAGE field.
10. Select ENGLISH from the list that displays.
LD21988LD21987
11. Press the Date and Time button in the lower right corner of the screen.
LD21989LD21987
12. The Time Setting screen displays.
LD21990LD21990
13. Enter the current date and the current time in the appropriate fields.
14. Press the OK button.
LD22161
LD22161
15. Check the date and time in the lower right corner of the screen
JOHNSON CONTROLS 65
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6LD22162LD22162
16. Press the Save button.
LD22163LD22163
17. The Save File screen appears.
18. Press the Yes button to complete the process.
LD22164LD22164
19. Press the Exit button to the right of the Save but-ton.
LD22165
LD22165
20. The Exit screen displays. Press the Yes button.
LD22166LD22166
21. The system automatically reboots. When the re-boot completes, you return to the Main screen.
JOHNSON CONTROLS66
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
• Thermo OFF: Lights if the district heating (hot)water temperature rises to the automatic stop tem-perature. Turns off if the automatic restart condi-tion is satisfied.
• Dilution: Lights during the dilution operation af-ter the heat pump stops. It turns off when the dilu-tion operation is complete.
• Source Water Pump: Lights if the heat source water pump answer back signal is ON. Light is off if the heat source water pump operation answer back signal is OFF.
• Hot Water Pump: Lights if the istrict heating (hot) water pump operation answer back signal is ON. Light is off if the district heating (hot) water pump operation answer back signal is OFF.
• Set Point: The set point of district heating (hot) water leaving temperature is shown on the left of the screen.
The system illustration lights (lines fill in) when the system is operating.
FIGURE 34 - MAIN SCREEN
LD29091
The Main Screen displays equipment status (heat pump operation/stop, pumps ON/OFF, purge sys-tem ON/OFF, and heat source and district heating (hot) water pumps ON/OFF). Also displayed is the op-erating status of the various modes of heat pump opera-tion.
Operating StatusOn the upper left of the screen, below the LOCAL and REMOTE buttons, is a list of options. Each has a lamp to indicate ON or OFF for the following items:
• Source Water Check: Lights if the heat source water pump operation answer back signal is ON and its flow suspension switch is ON continuous-ly for 5 seconds. Light is off if not.
• Hot Water Check: Lights if the district heating (hot) water pump operation answer back signal is ON and its flow suspension switch is ON continu-ously for 5 seconds. Light is off if not.
• Temperature Control: Lights if the tempera-ture control of the microcomputer panel changes to RUN status. Turns off if temperature control changes to STOP status due to heat pump stop or automatic stop.
MAIN SCREEN
JOHNSON CONTROLS 67
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
An illustration of the system shows the following information:
• Steam Drain Control Valve Output
• Steam Drain Control Valve MFB (Motor Feed-back) Value (If Available)
• Heat Source Water Entering And Leaving Tem-perature
• District Heating (Hot) Water Absorber Entering, Absorber Leaving, And Condenser Leaving Tem-perature
• Evaporator Refrigerant Temperature
• Generator Pressure
• Generator Solution Temperature
• Generator Solution Concentration
• Purge Tank Pressure
This screen shows the status of the equipment in the heat pump process diagram.
Items in the heat pump process diagram are:
Pump
Solution Circulating Pump, Solution Spray Pump, Refrigerant Pump, Purge Pump, Heat Source Wa-ter Pump, District Heating (Hot) Water Pump
Flickers white during operation. Remains black when the pump is stopped.
69WC1 or 69WC2
Differential pressure switch is of heat source water (69WC1) and district heating (hot) water (69WC2)
White when water is flowing. Turns black when
the water is stopped
33RL
Level switch of refrigerant in evaporator
White when the refrigerant level in evaporator is high enough to operate the refrigerant pump. Turns black when the refrigerant level in evapora-tor is low
Valve
Steam drain control valve, refrigerant blow valve, purge tank valve
White indicates the valve is shut off. Any other color indicates the valve is open.
The condition lights show the current operating mode and status of the system.
The five (5) buttons along the bottom of the Main screen are common to many of the other screens in the Control Panel. They all can be used to move around and access other screen informa-tion. They are:
• MAIN: return to the intitial screen
• DATA: move to the Data screen
• FAIL or ALARM: move to the Failure and Alarm screen
• CONTROL: move to the Control screen
• SETTING: move to the Setting screen
JOHNSON CONTROLS68
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
The Data Screen displays values showing tempera-tures, operating hours, operating frequency, data trends and a history of failures, alarms, and time based tem-perature trends.
In the Measured Value section of the Data screen, the following is displayed:
• Hot Water In Temperature: Temperature of the district heating (hot) water measured as it enters the absorber.
• Hot Water Absorption Out Temperature: Tem-perature of the district heating (hot) water mea-sured as it leaves the absorber.
• Hot Water Out Temperature: Temperature of the district heating (hot) water measured as it leaves the condenser.
• Source Water In Temperature: Temperature of the heat source water measured as it enters the evaporator.
• Source Water Out Temperature: Temperature of the heat source water measured as it leaves the evaporator.
• Evaporator Refrigerant Temperature: Temper-ature of the refrigerant in the evaporator.
• Generator Temperature: Temperature of the concentrated solution in the generator.
• Generator Pressure: Pressure in the generator.
• Generator Concentration: Concentration of the concentrated solution in the generator.
• Purge Tank Pressure: Pressure in the purge tank.
Control Output and MFB (motor feedback) of the steam condensate control valve (if available) are shown as a percentage.
The Operation Hours section shows the following:
• Heat Pump: Displays how long the heat pump unit has been running.
• Solution Pump: Displays how long the solution pump has been running.
• Refrigerant Pump: Displays how long the re-frigerant pump has been running.
DATA SCREEN
FIGURE 35 - DATA SCREENLD29097
JOHNSON CONTROLS 69
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
The frequency of failures, alarms, and purges is shown in the Frequency section:
• Operation: Displays how many times the heat pump unit has started using the OPER. button or the remote start signal
• Failure: Displays how many times the system has experienced a failure.
• Alarm: Displays how many times an alarm has been activated.
• Auto. Purge: Displays how many times the purge system has started automatically.
The History Menu section on the right side of the screen gives you access to the Trend Data screen and
the Failure and Alarm History screens. It contains two buttons:
• Failure: Move to the Failure and Alarm History screen
• Trend: Move to the Trend Data screen
JOHNSON CONTROLS70
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
FAILURE AND ALARM HISTORY SCREEN
FIGURE 36 - FAILURE AND ALARM HISTORY SCREENLD29098
The Failure and Alarm History Screen shows informa-tion for the last event and up to twenty previous events. It contains the following fields of information:
• Date: Date the alarm or failure was triggered
• Trigger: Time that the alarm or failure was trig-gered
• Message: Event that triggered the alarm
The buttons on the lower left side of the screen are used to move through the messages. The Double Up Arrow button moves you to the top of the list. The Single Up Arrow button moves you upward through the list one event at a time.
The Single Down Arrow button moves you downward through the list one event at a time. The Double Down
Arrow button takes you right to the bottom of the list.
Press and hold the ALL CLR button to delete the en-tire list of messages. Press and hold the CLR button to delete a single highlighted message.
Press the BACK button in the lower left corner to re-turn to the Failure and Alarm Screen.
Press the CLOSE button in the lower right corner to return to the Data screen.
JOHNSON CONTROLS 71
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
TREND DATA SCREEN
FIGURE 37 - TREND DATA SCREENLD29099
Press the TREND button on the Data screen to access this information.
This screen graphically illustrates the trend of the tem-perature and the water flow volume for the following:
• Hot Water In: Temperature of the district heating (hot) water measured as it enters the absorber.
• Hot Water Out: Temperature of the district heat-ing (hot) water measured as it leaves the condens-er.
• Hot Water Absorption Out (23C): Temperature of the district heating (hot) water measured as it leaves the absorber.
• Source Water In: Temperature of the heat source water measured as it enters the evaporator.
• Source Water Out: Temperature of the heat source water measured as it leaves the evaporator.
• Generator Temperature: Temperature of the concentrated solution in the generator.
• Generator Pressure: Pressure in the generator.
These graphs are updated constantly regardless of the operating status of the heat pump.
The display ranges in the Trend screen can be changed. See Screen Name Buttons: Located along the bottom of the screen. These are used to change screens. The selected button lights when it is active. on page 63 for more information on how to make the changes.
LD29100
Press the DATA button to return to the Data screen. Or, you can press any of the other available buttons to change your destination screen.
JOHNSON CONTROLS72
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
FAILURE AND ALARM SCREEN
FIGURE 38 - FAILURE AND ALARM SCREENLD29101
This screen displays failure indications (water sus-pension, operation interlock, over and under tempera-tures, and problems with the unit's pumps) and system alarms.
If a failure occurs, this screen automatically displays.
FailureWhen a failure occurs, an alarm sounds (buzzer). The type of failure button lights in the Failure section of the screen. Press the BUZZER STOP button to turn off the alarm sound. Turning off the buzzer does NOT fix the problem.
Press the lit failure button to access an on-screen han-dling guide for each item. An on-screen guide is avail-able for each item in the Failure and the Alarm sec-tions. See an example to the right
The failure light in the upper right corner is red. The alarm light is orange
After fixing the failure, press the FAILURE RESET button to reset the lighted failure button.
If you press the FAILURE RESET button before fix-ing the problem, the lighted failure button will not go out, and the buzzer will sound again.
Press the CLOSE button to return to the Failure and Alarm screen
LD29102
JOHNSON CONTROLS 73
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
TABLE 19 - FAILURE LISTBUTTON AND FAILURE
NAMEOPERATION AT FAILURE
OCCURRENCECAUSE
Hot W. Pump Interlock (Hot Water Pump Interlock)
Stop after dilutionDistrict heating (hot) water pump interlock was not established during district heating (hot) water pump operation command output
Source W. Pump Interlock(Heat Source Water Pump Interlock)
Stop after dilutionHeat source water pump interlock was not established during heat source water pump operation command output.
Source W. Suspension(Heat Source Water Suspension)
Stop without dilutionHeat source water flow suspension was detected during solution pump operation.
Hot W. SuspensionHot Water Suspension
Stop after dilutionDistrict heating (hot) water flow suspension was detected during solution pump operation.
Source W. Overcooled(Heat Source Water Overcooloed)
Stop without dilutionHeat source water outlet temperature was abnormally low during operation
Refrigerant Overcooloed Stop without dilutionRefrigerant temperature was abnormally low during operation.
High Hot Water In Temp.(High Hot Water Inlet Temperature)
Stop after dilutionDistrict heating (hot) water inlet temperature had been beyond the upper limit for at least 30 min
High Hot Water Out Temp.(High Hot Water Outlet Temperature)
Stop after dilutionDistrict heating (hot) water outlet temperature had been beyond the upper limit for at least 30 min.
High GEN Temperature(High Generator Temperature)
Stop after dilution Generator solution temperature rose abnormally
High GEN Pressure(High Generator Pressure)
Stop after dilution Generator pressure rose abnormally.
Sol. Circu. P. Abnormal(Solution Circulation Pump Abnormal)
Stop without dilutionSolution circulation pump thermal relay or overheat switch was activated.
Sol. Spray P. Abnormal(Solution Spray Pump Abnormal)
Stop without dilutionSolution spray pump thermal relay or overheat switch was activated.
Refrigerant P. Abnormal(Refrigerant Pump Abnormal)
Stop without dilutionRefrigerant pump thermal relay or overheat switch was activated.
Control Sensor Abnormal Stop after dilutionTemperature sensor or pressure sensor detected an abnormal value due to dicconnection, short circuit, etc
CPU Abnormal Stop after dilution CPU was judged to be abnormal.
AlarmWhen an alarm occurs, the type of alarm will light up in the Alarm section of the screen. See Figure 38 on page 72. There is no buzzer.
Press the lit alarm button to access an on-screen han-dling guide for each item in the Alarm section.
After fixing the alarm, press the ALARM RESET button to reset the lighted alarm button. If you press the ALARM RESET button before fixing the prob-lem, the lit alarm button will not go out.
JOHNSON CONTROLS74
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
TABLE 20 - ALARM LISTBUTTON AND ALARM
NAMECAUSE OF ALARM AND CONDITION TO RESET
COUNTERMEASURES
Purge Abnormal
The over current (thermal) relay for the vacuum pump activates. The alarm is reset when you press the ALARM RESET button after you press the reset button of the over
current (thermal) relay.Or, the purge switch had been ON for 10 minites since the purge operation
was started.
Contact your local Johnson Controls Service Center.
High GEN Pressure(High Generator Pressure)
Generator pressure rose enough to trigger the load limit operation.
The alarm is reset when the pressure falls.
Check the district heating (hot) water line.Check the district heating (hot) water flow rate.Purge manually according to instructions in SECTION 7 - MAINTENANCE.Contact your local Johnson Controls Service Center
Recording Sensor Abnormal
The temperature sensor or the pressure sensor detected an abnormal value due to a
disconnection, short circuit, etc.Press ALARM RESET button when the temperature returns to normal.
Tighten the terminals.Contact your local Johnson Controls Service Cemter.
Low Battery Voltage
Voltage level of the battery in the control board fell down.
Press the ALARM RESET button to clear the alarm after you replace the
battery in the control board.
Replace the battery on the PWB.
To move to another screen, press the any of the avail-able buttons along the bottom of the screen.
JOHNSON CONTROLS 75
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
CONTROL SCREEN
FIGURE 39 - CONTROL SCREEN
LD29103
Use this screen to check the status of the steam or steam condensate (drain) control valve. How the valve operates can also be changed here. Control parameters can be checked, and if needed, you may make updates.
Press the CONTROL button to access the screen.
STEAM OR STEAM DRAIN VALVE CONTROLCapacity control of an absorption heat pump is done automatically. It is done by controlling the amount of the steam that goes into the Generator and goes back to the steam condensate (drain) line via the steam drain control valve. The heat source water outlet temperature is key to the equation.
Capacity control is also done with the heat source wa-ter outlet temperature and the district heating (hot) wa-ter absorber outlet temperature.
The details of the steam or steam drain control valve are shown on the Control screen.
Use this screen to check the status of the steam or steam drain control valve. How the valve operates can also be changed here. Control parameters can be checked, and if needed, you may make updates. See Screen Name
Buttons: Located along the bottom of the screen. These are used to change screens. The selected button lights when it is active. on page 63 for information on how to make changes.
The operation mode selection button section contains two buttons:
• MANUAL: Press and hold until the button lights to operate the steam or steam condensate (drain) valve manually.
• AUTO: Press and hold until the button lights to allow automatic operation of the steam or steam condensate (drain) valve.
LD29104
JOHNSON CONTROLS76
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
If you change the operation mode of the Steam or Steam Drain Control Valve to MANUAL, be sure to change it back to AUTO Continued operation in manual mode may cause damage to and failure of the heat pump.
The hot water outlet temperature control (23A) section show information about the following:
• Hot Water Outlet: Temperature of the district heating (hot) water as it leaves the condenser.
• Setting Value: Control target of the district heat-ing (hot) water condenser outlet temperature de-termined by the local SP or remote SP.
• Control Output: Shown as a percentage
The heat source water outlet temperature control (23B) section show information about the following:
• Heat Source Water Outlet: Temperature of the heat source water as it leaves the evaporator.
• Setting Value: Control target of the heat source water outlet temperature.
This value can be changed by pressing the numer-ical value section.
• Output: Shown as a percentage.
The hot water absorber outlet temperature control (23C) section show information about the following:
• Hot Water Absorber Outlet: Temperature of the district heating (hot) water as it leaves the ab-sorber.
• Setting Value: Control target of the district heat-ing (hot) water condenser outlet temperature de-termined by the heat source water outlet tempera-ture.
• Control Output: Shown as a percentage.
The hot water absorber outlet temperature control (23D) section show information about the following:
• Hot Water Absorber Outlet: Temperature of the
district heating (hot) water as it leaves the absorb-er.
• Setting Value: Control target of the district heat-ing (hot) water condenser outlet temperature de-termined by the district heating (hot) water inlet temperature
• Control Output: Shown as a percentage
The 23A local/remote selection button section contains two buttons:
• Local: Control target of the district heating (hot) water condenser outlet temperature can be changed by pressing the numerical value section of the LO-CAL SP.
• Remote: Control target of the district heating (hot) water condenser outlet temperature can be changed by the remote signal. Its setting value is indicated in the REMOTE SP.
The two fields on the lower right of the screen are:
• Manual Input: Enter the desired control target value while the manual operation mode is select-ed.
• Actual Output: Output of the 23A, 23B, 23C, and 23D, whichever is lowest, displays in this col-umn.This value is used for actual control.
The settings for the Steam or Steam Drain Control Valve Operation may be updated if needed for service and maintenance.
For detailed information on how to make the changes-see Change Numeric Values on page 60 .
Press the 23A/B parameter button to show the control parameter (proportional band and integral time) of the temperature control 23A and 23B.
Set the control parameter for 23A and 23B.
Press the 23A/B Para key to set the control parameter.
Hot Water Out (23A): Hot water outlet temperature.
Prop. Band: Proportional band setting.
Integ. Time: Integral time setting.
Source W. Out (23B): Heat source water outlet tem-perature.
Prop. Band: Proportional band setting.
Integ. Time: Integral time setting.
LD29016
JOHNSON CONTROLS 77
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
Press the 23C/D parameter button to show the control parameter (proportional band and integral time) of the temperature control 23C and 23D.
Press the Check Setting button to show the calcula-tion details of the temperature control 23C and 23D.
The left curve is to calculate the SV for hot water ab-sorptionn outlet temperature control with source water outlet temperature.
The horizontal axis is to set the minimum and maxi-mum value of heat source temperature.
The vertical axis is to set the minimum and maximum hot water ABS outlet temperature
Source hot water temperature is to set the design source hot water temperature..
LD29107
FIGURE 40 - CONTROL PARAMETERS OF 23A AND 23B
LD29108
FIGURE 41 - CALCULATION DETAILS OF 23C AND 23D
Setting value is to set the design hot water absorption outlet temperature.
The right curve is to calculate the SV for hot water ab-sorption outlet temperature control with hot water inlet temperature.
The horizontal axis is to set the minimum and maxi-mum value of hot water inlet temperature.
The vertical axis is to set the minimum and maximum hot water ABS outlet temperature
Hot water inlet temperature is to set the design hot wa-ter inlet temperature.
Setting value is to set the design hot water ABS outlet temperature
JOHNSON CONTROLS78
SECTION 6 – OPERATION FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
SETTING SCREEN
FIGURE 42 - SETTING SCREEN
LD29109
This screen displays operation witch (forced dilution, refrigerant pump, water jet purge mode, and purge pump), and language (Japanese, English, and Chinese
Press the SETTING button to access this screen.
OPERATION SWITCHIn this screen section, choices can be made about the mode of operation for the various devices. Use the but-tons to make your choice. The choices are:
• Forced Dilution: Indicates whether forced dilution is ON or OFF.
• Refrigerant Pump: Indicates whether the re-frigerant pump s operating automatically (Auto mode) or is stopped (Stop mode).
• Manual Water Jet Purge Mode: The Auto and Manual buttons control the purge operation. The lit button indicates if the purge mode is Automatic or Manual.
• Purge Pump: The ON and OFF buttons control the manual purge operation. The lit button tells you if the manual purge operation is running or not. If you press the Purge Mode Auto button, the purge is done automatically. If you press the Purge Mode Manual button, the purge starts when you press the Manual Purge ON button. The purge stops when you press the Manual Purge OFF but-ton.
Any of these may be changed.
SELECT LANGUAGEPress the button to choose the language to display the desired language in the Control Center. Various lan-guages are available.
JOHNSON CONTROLS 79
SECTION 6 – OPERATIONFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
6
THIS PAGE INTENTIONALLY LEFT BLANK.
JOHNSON CONTROLS80
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
SECTION 7 – MAINTENANCE
When inspecting and maintaining the absorption heat-pump, note the following:
• Never splash water over the electrical parts in-stalled in the control panel and absorption heat-pump.
• Do not change the set values of the control de-vices and safety switches without permission.
• Do not turn the internal cycle control valve of the absorption heat-pump without permission.
• When you replace the oil in the vacuum pump, be sure to turn OFF the main circuit breaker (MCB1) in the control panel.
VALVE INSPECTIONThe heat pump is equipped with a refrigerant manual blow valve (VR1) that blows refrigerant from the re-frigerant tank to the absorber. See Figure 42 on page 97.
The valve must not be tampered with or have its set-tings changed. Daily maintenance or inspection is the only reason to touch the valve.
During service and maintenance work, be sure to turn OFF the main circuit breaker (MCB1) and close the main valve of the steam line. If you do not, it may cause electric shock or a burn.
Contact your local Johnson Controls Service Office for inspection and mainte-nance of the machine. Improper inspec-tion and maintenance can not only cause a machine problem but also injure workers.
Solenoid ValvesThe absorption heat pump is equipped with the follow-ing solenoid valves.
TABLE 21 - SOLENOID VALVESSOLENOID VALVE
NAME SYMBOL FUNCTION
Purge solenoid valve (1) ASV1Close water jet purge piping
Purge solenoid valve (2) ASV2Purge solenoid valve (3) ASV3
Refrigerant blow solenoid valve
SV7Close automatic refrigerant blow piping
PUMP SHUT OFF VALVES (OPTION)The heat pump is equipped with the pump shut off valves shown in Figure 42 on page 97. They are used for inspection of the pumps.
If the absorption heat-pump is operated with incorrect valve settings, the pump may be damaged. Do NOT tamper with the valves.
AIR PURGE VALVES AND DRAIN VALVES FOR STEAM, HEAT SOURCE WATER, AND HOT WATERThe heat pump is equipped with air purge valves and drain valves for the heat source water, and hot water . It is equipped with a drain valve for the steam condensate (drain). They are used to drain the heat source water, hot water, and steam condensate (drain). They are also used to purge air when water is supplied.
PURGE VALVESThe heat pump is equipped with the purging valves shown in Figure 43 on page 83 and Figure 44 on page 86. For operation of those valves, see Purge Procedure on page 81.
JOHNSON CONTROLS 81
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
START THE HEAT PUMP AFTER IT HAS BEEN STOPPED FOR A LONG PERIODWhen you start the heat pump after it has not run for a long time, use the following procedure.
1. Check the insulation of the Control Center and the electric system.
2. Check the operation of the Control Center and the safety devices.
3. Check that the refrigerant blow valve VR1 is closed.
4. Check the vacuum level in the machine. Use the pressure gauge of the generator.
It should be less than -0.1 MPaG.
5. Check the source water and hot water supply.
6. Check the steam pressure.
7. Press the Refrigerant Pump Stop button.
If the checks show no problems, start the heat pump.
Checks After Operation Starts• 10-15 minutes after the heat pump and the solu-
tion pump start, check the level gauge of the re-frigerant tank.
• If the refrigerant level is within the level gauge, press the Refrigerant Pump Auto button.
• Observe the operation for a while. Check that the refrigerant liquid level does not drop.
• Use the procedure shown in Purge Procedure on page 81 to purge non-condensable gas from the low pressure side (absorber).
Remember: Only deionized water may be used as the refrigerant in the heat pump!
PURGE PROCEDURENon-condensable gas, including air, must be purged from the heat pump to maintain its performance and prevent deterioration of its internal parts. This heat pump has an automatic purge system.
The automatic purge is done by the water jet purge sys-tem. The system uses the heat source water pressure as the driving force. It ejects non-condensable gas from the purge tank via an aspirator.
Even if the automatic purge mode is used during nor-mal operation, perform the manual operation for the purging tank and absorber periodically. For the purging period, see Table 23 on page 91.
During a water jet purge, put the uncon-nected end of the water discharge hose in a drain ditch or drain port. If you do not, flooding may result.
Be sure the one end of the hose is not connected to anything. Otherwise, the automatic purge will not work properly
JOHNSON CONTROLS82
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
PERFORMANCE CHECK METHOD OF VACUUM PUMPFor commissioning and regular maintenance, check the performance of the vacuum pump first according to the following procedure.
1. Check the oil level in the vacuum pump.
2. If the oil is cloudy, it contains water and must be replaced with new oil.
See the Operation Manual for the Vacuum Pump for more information on how to change the oil.
3. Open the gas ballast.
If the purge unit is operated with the gas ballast closed, water is left in the oil. The oil will need to be replaced more frequently.
4. Set the valves according to pattern D shown in Table 22 on page 86 .
5. Press the Purge Pump ON button. The vacuum pump starts.
6. 1-2 minutes after the vacuum pump starts, con-firm that the vacuum gauge stands at 0 - approxi-mately 1 kPa.abs.
7. Press the Purge Pump OFF button. The vacuum pump stops.
8. Wait for 30 minutes.
9. Confirm that the vacuum down is within 2 kPa.
JOHNSON CONTROLS 83
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
LD27830
FIGURE 43 - LOCATION OF MANUAL VALVE IN PURGING SYSTEM (EXAMPLE)
VP9 Purge operating valve for absorber lineVP8 Purge operating valve for purge tank line
ASV3 Water jet solenoid valve for gas line (2)V10 Purge main valve
ASV2 Water jet solenoid valve for gas line (1)VP2 Water jet service valve for gas line VP1 Water jet service valve for water line
ASV1 Water jet solenoid valve for water lineVP6 Purge operating valve for condenser line (3)VP5 Purge operating valve for condenser line (2)VP4 Purge operating valve for condenser line (1)VP7 Purge operating valve for condenser direct purge line
JOHNSON CONTROLS84
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
MANUAL METHOD TO PURGE NON-CONDENSABLE GAS DIRECTLY FROM ABSORBER WITH VACUUM PUMPWhen the heat pump operates at a lower capacity than usual for a long period of time or when it restarts after a power failure, the absorber may contain non-condens-able gases. If the machine starts under these conditions, its performance and efficiency go down. If this hap-pens, purge non-condensable gas directly from the ab-sorber manually according to the following procedure.
Do NOT purge using the vacuum pump while the heat pump operates. The vacu-um pump may fail.
1. Set the valves according to pattern D shown in Table 22 on page 86.
2. Press the Purge Pump ON button. The vacuum pump starts.
3. After step 2 begins, confirm that vacuum gauge stands at 0 ~1 kPa.abs.
4. Reading the vacuum gauge, open valve VP9 grad-ually. Confirm that the pressure on the vacuum gauge increases slightly.
If the pressure decreases when valve VP9 opens, the vacuum pump capacity is insuf-ficient. Close valve VP9 at once. Check the purge line.
5. If no problems are found, open valve VP9. The valve pattern now matches pattern B shown in Table 22 on page 86.
Make sure the valve is completely open.
6. Continue to purge for 2 to 3 hours.
7. Close valve VP9.
8. Press the Purge Pump OFF button. The vacuum pump stops.
MANUAL METHOD TO PURGE NON-CONDENSABLE GAS FROM PURGING TANK WITH VACUUM PUMPWhile the absorption heat-pump operates, non-con-densable gas collects in the purging tank. You can purge those gases manually using the following procedure.
Do NOT purge using the vacuum pump while the heat pump operates. The vacu-um pump may fail.
1. Set the valves according to pattern D shown in Table 22 on page 86.
2. Press the Purge Pump ON button. The vacuum pump starts.
3. 3-4 minutes after the vacuum pump starts, con-firm that the vacuum gauge stands at 0~1 kPa.abs.
4. Reading the vacuum gauge, gradually open valve VP8. The valve pattern now matches pattern A shown in Table 22 on page 86.
5. The manual purge procedure is complete when the pressure reaches 3 kPa.abs or less on the vac-uum gauge.
6. Close valve VP8.
7. Press the Purge Pump OFF button. The vacuum pump stops.
JOHNSON CONTROLS 85
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
AUTOMATIC METHOD TO PURGE NON-CONDENSABLE GAS FROM PURGING TANK BY WATER JET PURGE SYSTEMThis heat pump has an automatic purge system. The purge solenoid valves automatically open and close by detecting the pressure inside the purge tank.
1. Set the valves in accordance with the Purge pat-tern C shown in Table 22 on page 86.
2. Press the Manual WJ Purge Auto button.
3. The purge solenoid valves automatically open and close.
During the automatic purge operation, the purge sole-noid valves open when the purging tank pressure in-creases abs and close when it decreases.
When you replace the oil in the vacuum pump or belt or perform maintenance work while the absorption heat pump is running, be sure to turn off the circuit breaker of the vacuum pump in the control panel. If not, the vacuum pump could start abruptly and cause injury.
JOHNSON CONTROLS86
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
TABLE 22 - VALVE OPERATION TABLEPURGE PATTERN USE VALVE NUMBER
VP1 VP2 VP3 VP4 VP5 VP6 VP7A Purge from purge tank O O O × O × OB Purge from absorber O O O × × O OC Water jet purge O O O × × × ×D Purge pump performance check O O O × × × O
O: Valve openx: Valve closed
LD28061
PG2
S
S
S
- - PG1 PT 1TE2
TE3
TE5
PA363SH1
TC123AS
LC33PU
TA126WL1
MS
PA663AP
TIC 323C
TE4
LS
PT 2
CAS SVFX1
TIC123A
M
LS
FX2
TIC 223B
CAS SV
TA326WH2
PA463SH2
PT3
PA563WH
LVS2
M
TC223AS2
PI
MPI
VP1
VP2
VP4VP3
VP5 VP6
VP7
Scope of supply
District Heating
Drain trap
Steam inletPurgetank
EvaporatorAbsorber
Gas separator
Heat SourceWater Inlet
Heat SourceWater Outlet
Refrigerantpump
Solutionspray pump
Solution heatexchanger
Generator
Condenser Refrigerantsub cooler
On-off valve(Supply)
Checkvalve
Steam draincontrol valve
Needlevalve
Steamcondensateoutlet
Steam condensateback pressureadjustment valve
On-off valve(Bypass)
Instrument(Installed in the heat pump)
Control device(in the PLC)
Steam shut-off valve
District Heating Water Outlet
Solution circulationpump
Discharged water from purge unit
FIGURE 44 - PURGE UNIT
JOHNSON CONTROLS 87
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
LD28062
PG2
S
PG1
PT1
S
S
TE1
TE2
TE3
TE5
TE6
TE7
TA4
26R
L
TA5
26SH
PA
363
SH
1TC
123
AS
1
LA 33R
L
LC 33PU
PA
169
WC
1
TA1
26W
L1
MS
PA
663
AP
TI
TIC
323
C
TE4
LS
PT2
CA
S-S
VFX
1
TIC
123
A
M
LS
FX2
TIC
223
B
CAS
-SV
TA3
26W
H2
PA
269
WC
2P
A4
63S
H2
PA
563
WH
LVS1
LVS2
TA2
26W
H1
M
TC2
23A
S2
PI
SV
MP
I
Sco
pe o
f sup
ply
Inst
rum
ent
(Inst
alle
d in
the
heat
pum
p)
Con
trol d
evic
e (in
the
PLC
)
Dis
trict
Hea
ting
Wat
er O
utle
t
On-
off v
alve
(Byp
ass)
Dis
trict
Hea
ting
Wat
er In
let
On-
off v
alve
(Sup
ply)
Stea
m d
rain
cont
rol v
alve
Nee
dle
valv
e
Che
ckva
lveS
team
co
nden
sate
ou
tlet
Stea
m c
onde
nsat
e ba
ck p
ress
ure
adju
stm
ent v
alve
Stea
m
shut
-off
valv
e
Dra
in tr
ap
Ste
am in
let
Pur
geta
nk
Eva
pora
tor
Abs
orbe
r
Sol
utio
n ci
rcul
atio
n pu
mp
Dis
char
ged
wat
er
from
pur
ge u
nit G
as s
epar
ator
Vac
uum
pum
p
Hea
t Sou
rce
Wat
er In
let
Hea
t Sou
rce
Wat
er O
utle
t
Ref
riger
ant
pum
p
Sol
utio
nsp
ray
pum
p
Sol
utio
n he
atex
chan
ger
Gen
erat
orC
onde
nser
Ref
riger
ant
sub
cool
er
Act
ual c
oolin
g de
man
d ca
lcul
atio
n
Flow
met
er(0~
500m
3/h)
Dev
ice
sym
bol
Des
crip
tion
Dev
ice
sym
bol
Des
crip
tion
Dev
ice
sym
bol
Des
crip
tion
TE1
Hea
t sou
rce
wat
er in
let t
emp
TA1(
26W
L1)
Hea
t sou
rce
wat
er te
mp
low
TIC
1(23
A)
Hea
t sou
rce
wat
er o
utle
t tem
p co
ntro
ller
TE2
Hea
t sou
rce
wat
er o
utle
t tem
pTA
2(26
WH
1)D
istri
ct h
eatin
g w
ater
inle
t tem
p hi
ghTI
C2(
23B
)D
istri
ct h
eatin
g w
ater
abs
orbe
r out
let t
emp
cont
rolle
r(1)
TE3
Dis
trict
hea
ting
wat
er in
let t
emp
TA3(
26W
H2)
Dis
trict
hea
ting
wat
er o
utle
t tem
p hi
ghTI
C3(
23C
)D
istri
ct h
eatin
g w
ater
abs
orbe
r out
let t
emp
cont
rolle
r(2)
TE4
Dis
trict
hea
ting
wat
er a
bsor
ber o
utle
t tem
pTA
4(26
RL)
Eva
pre
frige
rant
tem
p lo
wTC
1(23
AS
1)A
utom
atic
on/
off s
witc
h (H
eat s
ourc
e w
ater
out
let)
TE5
Dis
trict
hea
ting
wat
er o
utle
t tem
pTA
5(26
SH
)G
ene
solu
tion
tem
p hi
ghTC
2(23
AS
2)A
utom
atic
on/
off s
witc
h (D
istri
ct h
eatin
g w
ater
abs
orbe
r out
let)
TE6
Eva
p re
frige
rant
tem
pP
A1(
69W
C1)
Hea
t sou
rce
wat
er fl
ow lo
wLC
(33P
U)
Det
ectio
n of
non
-con
dens
able
gas
acc
umul
atio
nTE
7G
ene
solu
tion
tem
pP
A2(
69W
C2)
Dis
trict
hea
ting
wat
er fl
ow lo
wFX
1Fu
nctio
n tra
nsm
itter
(for
cas
cade
SV
to 2
3C)
PT1
Gen
e pr
essu
re tr
ansm
itter
PA
3(63
SH
1)G
ene
pres
sure
hig
hFX
2Fu
nctio
n tra
nsm
itter
(to
bias
cas
cade
SV
to 2
3B)
PT2
Pur
ge li
ne p
ress
ure
trans
mitt
erP
A4(
63S
H2)
Gen
e pr
essu
re h
igh
alar
mLV
S1
Eva
pre
frige
rant
leve
l sw
itch
PT3
Dis
trict
hea
ting
wat
er p
ress
ure
trans
mitt
erP
A5(
63W
H)
Dis
trict
hea
ting
wat
er p
ress
ure
high
LVS
2G
as s
epar
ator
leve
l sw
itch
PA
6(63
AP
)P
urge
line
pre
ssur
e hi
ghP
G1
Gen
e co
mpo
und
gaug
eLA
(33R
L)E
vap
refri
gera
nt le
vel l
owP
G2
Pur
ge li
ne v
acuu
m g
auge
FIGURE 45 - PROCESS AND INSTRUMENTATION DIAGRAM
JOHNSON CONTROLS88
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
REFRIGERANT REFINING METHODRemember: Only deionized water may be used as the refrigerant in the heat pump!
With an increase in the operation time of the heat pump, some of the solution can mix in with the refrig-erant. Mixing the solution and the refrigerant lowers the performance of the unit. To prevent this, the refrig-erant must be refined periodically.
Refine the refrigerant according to the following pro-cedure. The heat pump must be operating to refine re-frigerant.
When refining refrigerant, operate the absorption heat-pump under a low load (50% or less) for higher refin-ing efficiency. Note that the performance of the unit is dramatically reduced during the refrigerant refining operation.
1. Remove the cap of the refrigerant manual blow valve VR1.
For the location of the refrigerant manual blow valve, see Figure 45 on page 87.
2. Turn the spindle in the valve to the left using an 8 mm hexagon wrench to start refining the refriger-ant.
3. After the refining process is complete, close the spindle in the valve (turn it to the right until it stops).
4. Return the valve cap. There is an O-ring between the cap and valve. When fitting the cap, make sure that the O-ring is set normally.
The time required for refinement of the refrigerant depends on the current load condition. Constantly check the liquid level in the refrigerant tank while the refrigerant is refined. If the refrigerant liquid level appears in the level gauge of the refrigerant tank, close the valve im-mediately and fully.
MANUAL REFRIGERANT BLOWDOWN AND DILUTING METHODWhen the heat pump stops suddenly due to a power failure, the solution can become crystallized. If this happens, dilute the solution manually according to the following procedure.
Perform the following procedure immedi-ately after the power is restored.
1. Press the Forced Dilution ON button. The solu-tion pump and refrigerant pump start.
2. Remove the cap of the refrigerant manual blow valve VR1.
For the location of the refrigerant manual blow valve, see Figure 45 on page 87.
3. Turn the spindle in the valve to the left with the 8 mm hexagon wrench. The refrigerant in the refrig-erant tank is diverted into the absorber.
4. Watch the liquid level of the refrigerant tank. Im-mediately after the refrigerant liquid level appears in the level gauge of the refrigerant tank, close the valve (turn it to the right until it stops).
5. Press the Refrigerant Pump Stop button. The re-frigerant pump stops.
6. Let the solution pump operate independently for 30 minutes.
7. Press the Forced Dilution OFF button to stop the solution pump.
8. Press the Refrigerant Pump Auto button.
9. Return the valve cap. There is an O-ring between the cap and valve. When fitting the cap, make sure that the O-ring is set normally.
JOHNSON CONTROLS 89
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
DECRYSTALLIZATION METHODEven if the solution in the absorption heat-pump is crystallized during operation, it can be melted if the crystallization is not severe. Since it becomes more dif-ficult to melt the crystals as time passes, perform the following operation immediately when crystallization is detected. If the crystals cannot be melted using the following procedure, notify your local Johnson Con-trols Service Center immediately.
Indications of Crystallization1. The heating capacity goes down, the liquid level
in the absorber drops, and cavitation noise comes out of the solution pump.
2. The Solution Circulation Pump Abnormal or the Solution Spray Pump Abnormal button lights and the solution pump trips.
3. The liquid level in the absorber is low. The solu-tion seen through the generator level gauge (G4) is white.
4. The liquid level in the absorber drops and the tem-perature of the solution returning from the genera-tor goes down.
Decrystallization1. Stop the absorption heat-pump. If the solution
pump tripped, reset the thermal relay.
2. Disconnect the electrical wiring of the solution pump.
3. Press the Forced Dilution ON button.
Since the electrical wiring of the solution pump is disconnected, only the refrigerant pump starts.
4. Remove the cap of the refrigerant manual blow- down valve VR1.
For the location of the refrigerant manual blow valve, see Figure 45 on page 87.
5. Turn the spindle in the valve to the left with the 8 mm hexagon wrench.
The refrigerant in the refrigerant tank diverts into the absorber.
6. Watch the liquid level of the refrigerant tank.
7. Immediately after the refrigerant liquid level ap-pears in the level gauge of the refrigerant tank, close the refrigerant manual blow-down valve (turn it to the right until it stops).
8. Press the Refrigerant Pump Stop button. The re-frigerant pump stops.
9. Press the Forced Dilution OFF button
10. Re-connect the electrical wiring of the solution pump.
11. Press the Forced Dilution ON button. The solu-tion pump starts.
12. Navigate to the Control screen.
13. Press the steam control valve or steam drain con-trol valve Manual button.
14. Set the Manual Input on the Control1 screen to 30 to 40%. Constantly observe the liquid level in the absorber during this period
15. When the liquid level in the absorber drops, stop the supply of steam and press the Forced Dilution OFF button.
16. Repeat steps 12 through 16 three - four times. If the liquid level in the absorber does not go down, the crystals have melted.
JOHNSON CONTROLS90
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
17. Stop the steam supply.
18. Let the solution pump operate independently for about 30 minutes. Constantly observe the liquid level in the absorber while the solution pump op-erates.
19. After about 30 minutes, stop the solution pump.
20. Press the refrigerant pumps Auto button
21. Return the valve cap. There is an O-ring between the cap and valve. When fitting the cap, make sure that the O-ring is set normally.
Precautions for Decrystallization1. Cycle the heat source and hot water pumps off and
on during the melting process.
2. Remove any sensors that are sensitive to heat be-fore you start the melting operation. The tempera-ture of the heat source and hot water that remains in the absorption heat-pump may rise to about 70°C.
3. When you start the heat pump after melting the crystals, discharge the heat source water and hot water first. If that water is left in the machine, the paint on the inside walls may be peeled off.
JOHNSON CONTROLS 91
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
MAINTENANCE ITEMSMaintenance and inspection items along with standard inspection periods are shown in the next table. For de-tails, contact your local Johnson Controls Service Cen-ter.
Inspection frequency may be adjusted according to the actual operating conditions.
TABLE 23 - MAINTENANCE AND INSPECTIONTASK CONTENTS FREQUENCY SCOPE
Record operation dataCollect the operation data. Refer to 155.36.CL1. Compare it with the factory test data.
Weekly C
Check liquid level.Check the gauges. Refer to “causes of abnormal levels of solution and refrigerant” for more information
Daily C
Check operation of the steam control valve or steam drain control valve
Make sure the valve operates smoothly Weekly C
Refrigerant refiningRefine the refrigerant. See Refrigerant Refining Method on page 88.
Every 2-3 weeks S
Manually purge the purge tank
Manually purge non-condensable gas from the purge tank. See the procedure shown in Manual Method to Purge Non-condensable Gas from Purging Tank with Vacuum Pump on page 84
Every 2-3 months. S
Manually purge the absorber
Manually purge the non-condensable gas from the absorber. See the procedure shown in Manual Method to Purge Non-condensable Gas Directly from Absorber with Vacuum Pump on page 84.
Replace vacuum pump oil
Change the oil in the vacuum pumpEvery 2-3 months C
Check the vacuum pump
After the oil change, check the pulley belt to be sure it runs smoothly.
Appearance inspectionCheck to see if there is any damage to the equipment. For example, look for heat source water or hot water leaks, rust, abnormal sounds or vibrations in the pumps.
Monthly C
Measure insulation resistance
Measure the insulation resistance of the main circuits and motors to see if the insulation is deteriorated. If it is, it needs to be replaced. When measuring the insulation resistance, be sure to disconnect the wires of the temperature controller, etc.
Yearly(1) S
Check terminals Check that each terminal in the control panel is tight Yearly SCheck control panel Check the operation of the control panel Yearly SCheck purge unit performance
Check the performance of the purge unit. See the procedure shown in Purge Procedure on page 81.
Every 6 months S
Check and overhaul purge check valve
Disassemble and clean the purge check valve. Yearly S
Check and overhaul purge solenoid valves
Disassemble and clean the purge solenoid valves. Yearly S
Check vacuum pump for leaks
Measure the amount of gas discharged from the vacuum pump.
Every 6 months S
C = Customer and S = Johnson Controls Service
JOHNSON CONTROLS92
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
TASK CONTENTS FREQUENCY SCOPECheck protective bonding circuit
Check the continuity of the protective bonding circuit. Yearly S
Water quality analysisReview the heat source water, hot water, and steam quality values
Every 2-3 months(2) C
Solution and refrigerant Verify the amount of the solution and the refrigerantYearly (while the unit is operating at 100%)
S
Steam chamber caseOpen and inspect the steam chamber case, the internal surface, and the tubes. Replace the packing.
Yearly S
Check solution pump and refrigerant pump
Disassemble and inspect the solution pump and the refrigerant pump. Clean the internal strainer
Every 2-3 years S
Check vacuum pump Disassemble, inspect, and clean the vacuum pump. Every 4 years SGaskets Replace gaskets in airtight parts Every 4 years SSource water chamber case
Open and inspect the water case, the internal coating, and the tubes. Replace the packing
Every 2 years S
Solution Filter the solution to remove contaminants Every 5-6 years SSafety relays Inspect each safety relay Yearly STube cleaning (evaporator, absorber, and condenser) Use brushes or a water jet system to remove slime and
contaminants in the tubes.
Every 2 yearsS
Tube cleaning (generator)
Every 4 years
Tube cleaning (evaporator, absorber, and condenser) Use a chemical cleaner to remove hard scale.
Every 4 yearsS
Tube cleaning (generator)
Every 8 years
Entire machineInspect for leaks that may affect the vacuum. (Special equipment may be required.)
Every 2 years S
Eddy current check on tubes (evaporator, absorber, and condenser) Inspect the tube interiors for corrosion. Every 8 years S
Eddy current check on tubes (generator)Hot water chamber case
Open and inspect the water case, the internal coating, and the tubes. Replace the packing
Every 2 years SSource water and hot water chamber cases
Inspect and repair the paint on the interior walls.
Solution inhibitor analysis
Review the concentration of the inhibitor in the solution. Check for leaks.
Every 6 months S
Check steam control valve or steam drain control valve
Check the steam control valve or steam drain control valve seat for leaks while the heat pump stops Yearly S
C = Customer and S = Johnson Controls Service
1. Before measuring insulation resistance, wiring such as temperature controller must be removed.2. First analysis should be done within one month of the commissioning.
TABLE 18 - MAINTENANCE AND INSPECTION (CONT'D)
JOHNSON CONTROLS 93
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
Refrigerant Pump Manual StopThe refrigerant pump can be stopped manually for maintenance purposes. It can be stopped even while the heat pump is operating.
1. Navigate to the Setting screen.
2. Press the Refrigerant Pump Stop button.
After maintenance of the refrigerant pump system is complete, be sure to reset it to auto. Continued operation in stop mode may cause damage to and failure of the heat pump.
Water Jet Purge Manual StopThe water jet purge can be started or stopped manually when the heat pump is running.
1. Navigate to the Setting screen.
LD29110
2. Press the Manual Water Jet Purge Manual button.
The water jet purge solenoid valves open. The water jet purge operation begins.
3. Press the Manual Water Jet Purge OFF button when the purge process is complete.
4. The water jet solenoid valves close.
After maintenance of the water jet purge system is complete, be sure to reset it to Auto. Continued operation in manual operation or manual stop mode may cause damage to and failure of the heat pump.
5. Press the Manual Water Jet Purge Auto button.
Start or Stop Vacuum Pump
Be sure the heat pump is not running while the purge pump runs.
1. Navigate to the Setting screen.
LD29111
2. Press the Purge Pump ON button.
The purge pump starts.
3. After the use of the purge pump is complete, press the Purge Pump OFF button. The pump will NOT stop automatically without this step.
Do NOT operate the purge pump while the heat pump is running.
JOHNSON CONTROLS94
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
LIFESPAN FOR VARIOUS PARTSThe replacement periods of the main parts are shown below. (The following periods are shown for reference only. They need to be changed according to the actual environment, frequency of use, etc. Other parts may need to be replaced if used incorrectly.)
TABLE 24 - LIFESPAN OF COMMON PARTSPART NAME LIFESPAN OF COMMON PARTS REMARKS
Heat source water Waterbox Gasket Every 2 yearsSteam Chamber Box Gasket Every 1 yearHW Waterbox Gasket Every 2 yearsGasket, O-ring, Diaphragm Every 24,000 HrEvaporator tube About 15 years
Depends on the eddy current result at interval 24-36 KHR.
Absorber tube About 15 yearsCondenser tube About 15 yearsGenerator tube About 15 yearsSequencer unit Every 30,000 HrRelay Every 30,000 HrTimer Every 30,000 HrCircuit Protector Every 30,000 HrPower unit Every 30,000 HrMagnet switch, Thermal relay Every 30,000 HrBattery for touch panel, sequencer CPU unit Every 5 yearsTouch panel Every 30,000 HrInverter (option) Every 30,000 HrTemperature controller Every 30,000 HrFan for control panel Every 30,000 HrSteam control valve or steam drain control valve Every 60,000 HrSteam shut-off valve (option) Every 60,000 HrSteam drain solenoid valve Every 20,000 HrDifferential pressure switch Every 30,000 HrPressure sensor Every 30,000 HrResistance temperature sensor Every 30,000 HrThermocouple Every 30,000 HrBearing for solution circulation pump Every 20,000 HrSolution circulation pump Every 60,000 HrBearing for solution spray pump Every 20,000 HrSolution spray pump Every 60,000 HrBearing for refrigerant pump Every 20,000 HrRefrigerant pump Every 60,000 HrVacuum pump Every 60,000 HrPump shut off valve (option) Every 48,000 HrPressure release valve Every 48,000 HrPurge solenoid valve Every 30,000 HrRefrigerant blow solenoid valve Every 30,000 HrFloat valve for refrigerant tank Every 60,000 HrFloat valve for generator float box Every 60,000 Hr
JOHNSON CONTROLS 95
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
PART NAME LIFESPAN OF COMMON PARTS REMARKSFloat valve for refrigerant float box Every 60,000 HrAspirator for water jet purge 3 yearsLevel switch for separator Every 5 yearsCompound gauge Every 48,000 HrVacuum gauge Every 48,000 HrRubber hose set for purge line Every 18,000 HrOil for purge pump Every monthRefrigerant tank float switch Every 60,000 Hr
WATER QUALITY CONTROLUse the following guidelines to be sure of the highest water quality control standards:
1. Limit the water pressure to the maximum safe working pressure for heat source and hot water.
2. Install a 10 or finer mesh strainer in the heat source and hot water piping.
3. Install a thermometer and a pressure gauge in the inlet and the outlet of the heat source and hot wa-ter piping.
4. Install tapping (with valve) for chemical cleaning of the inlet and the outlet of the heat source and hot water piping.
5. Install an air vent valve at the highest part of the piping and a drain valve at the lowest part of the piping.
6. Replace the water regularly and control the water quality. Operating the heat pump for long periods of time with low quality water will cause corro-sion and the production of scale.
7. Close the main steam supply valve during an ex-tended shut down.
8. Make sure the shut off valves installed at the heat
TABLE 19 - LIFESPAN OF COMMON PARTS (CONT'D)
6. pump inlet of the heat source water and hot water are completely open.
If the heat pump runs without the valves completely open, a strong turbulent flow can be generated. The turbulence may cause damage in the water chamber case and the copper tube of the heat pump. If you need to adjust the flow rate of the heat source water and the hot water, be sure to adjust the valves installed at the outlet side of the heat pump.
7. Install a safety valve on the steam line.
8. Install an expansion tank on the hot water line if the hot water is a closed system.
JOHNSON CONTROLS96
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
CHEMICAL WATER TREATMENTSince the mineral content of the water circulated through the evaporator, condenser, absorber, and gen-erator varies, the water being used may corrode the tubes or deposit heat resistant scale in them.
Perform a chemical analysis of the water before the system is installed. Consult a reliable water treatment company to determine if treatment is necessary. If it is, the company can provide treatment for the water to help prevent damage to the tubes.
REPLACEMENT OF WATERIf the heat source water line or the hot water line are open systems, they must be cleaned or replaced peri-odically. If the water is not treated at all in the water line, the recommended intervals for replacement of both types of water are:
District polluted with sulfurous acid gas --- 5 days
Common district --- 10 days
If the water is blown manually or automatically, the replacement period may be lengthened as follows.
District polluted with sulfurous acid gas --- 1 month
Common district --- 1 month
TREATMENT FOR LONG STOPPAGE OF THE ABSORPTION HEAT-PUMPIf the absorption heat-pump is stopped for a long time, bacteria in the water or in the tubes may grow. The bacteria can corrode the tubes. When stopping the heat pump for more than 15 days, drain the water from the absorber, condenser, evaporator, and generator through the drain valve at the bottom of the waterbox.
CHEMICAL TREATMENTCorrosion inhibitors are attracted chemically to corrod-ed metal surfaces. Or, they form inert protective com-pounds over the metal surfaces. For effective use of the corrosion inhibitors, be sure to choose the correct type and concentration. Water quality, temperature, flow speed, metals used, existence of crevices and deposits and type of water system are also part of the equation. For more information about corrosion preventive mea-sures, consult a water treatment company.
FLOW SPEED IN TUBESSince the water flow speed in the tubes is closely re-lated to any existing corrosion, do not increase the wa-ter supply rate more than recommended. If the flow speed reaches 3.5 to 4 meters per second, the tubes may erode. When changing the flow rate, contact your local Johnson Controls Service Center.
If the water supply rate is adjusted at the inlet side of the heat exchanger (evaporator, condenser, and absorb-er), the eddy current at the inlet may corrode the tube.
Accordingly, be sure to control the flow rate on the out-let side.
The eddy current caused by foreign matter in the heat exchanger is also a factor in corrosion. Be sure to in-stall a strainer on the inlet side of the heat exchanger and clean the strainer periodically.
JOHNSON CONTROLS 97
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
TABLE 25 - TENDENCY OF GENERATION OF SCALES AND CORROSION BY QUALITY OF HOT AND HEAT SOURCE WATER
QUALITY OF HOT AND HEAT SOURCE WATER
GENERAL TENDENCY SCALE AND ITS COLOR CORROSION AND ITS COLOR
Factors of Water Quality
Water PH low Hard scales are generated and iron bacteria propagate
Corrosion of iron and copper
Dark brown ~ Pale greenish blue
Water PH high Calcium carbonate scales are generated easily.
Pale yellow
──
Water contains many calcium ions (Ca2+) and magnesium ions(Mg2+)
Sulfate ion SO42- silica SiO2
and carbonate ion CO32-
combine together to generate hard scale.
Pale yellow
──
Water contains many chlorine ion (Cl-)
── Iron and copper tubes corrode badly.
Water contains many sulfate ions (SO4
2-) and silica (SiO2)
Calcium sulfide (CaSO4) and calcium silicate (CaSiO3) combine together to generate hard scales.
Gray SO4
2- corrodes copper tubes badly.
Greenish Blue
Water contains many iron (Ferrous ions (Fe3+),ferric ions (Fe2+))
Fe3 becomes ferric hydroxide (Fe(OH)3) to make water turn red and sets red rust of ferric oxide (Fe2O3). Iron bacteria propagate quickly.
Reddish brown-Black
Fe3+ corrodes iron and copper tubes badly.
Reddish brown-Black
Environmental Factors
Water smells bad (Contains compounds of sulfur, hydrogen sulfide (H2S), ammonium ions (NH4
+), methane, etc.)
Scales and slime created easily.
Greenish Blue – Dark brown
H2S and NH4+
corrodes copper tubes badly.
Black – Greenish blue
Water contains organic matter (High COD and BOD)
Scales and slime are created easily.
──
Exhaust gases (Sulfurous acid gas (SO2), nitrogen oxide (NO2), hydrogen chloride (HCl), ammonia (NH3) mixed in water in cooling tower
If organic nitrogen and inorganic nitrogen are contained, algae propagate. SO2 becomes SO4
2- and combines with Ca2+ and Mg2+ to generate scales.
Algae: Green Pale yellow
Exhaust gas from cars, factories, sewage plants, ammonia refrigeration machine, lower or raise PH number. As SO4
2- Cl- and NH4+
increases, tubes are corroded and pitted very quickly.
Solid matter (Mud, sand, fibers, dust, insects) in water in cooling tower
Scales are generated easily. Solid matters set. Slime is generated.
────
Sea wind (District by sea) Scales are generated easily. Tubes corrode badly. Reddish brown-Black
JOHNSON CONTROLS98
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Heat SourceWater Pump
Flow MeterAbsorption Heat Pump
TI:ThermometerPI:Pressure GaugeFlow MeterHot Water
Pump
Scope of Supply
Heat SourceWater Return
Hot Water Return
Heat SourceWater Supply
Hot Water Supply
LD29112
FIGURE 46 - HEAT SOURCE WATER AND HOT WATER SYSTEM
JOHNSON CONTROLS 99
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
TABLE 26 - STEAM DRAIN QUALITY CONTROLCOMPONENT STANDARD VALUE
PH 7.5 ~ 8.5Cl- (ppm) ≤ 20
SO42- (ppm) ≤ 10
H2S (ppm) nilDO (ppm) ≤ 0.5
All carbonate (ppm) ≤ 20
LD22006a
Scope of Supply
Go Down to Heat PumpSteam Inlet
Pressure Gauge
Steam Shut OffValve
High Temperature GeneratorSteam Header
Steam
Drain Trap
Steam ControlValve
Check ValveDrain Back PressureAdjusting Valve
Hotwell Tank
Safety ReliefValve
Straner(60 ~70 mesh)
(Drain Back Pressure)- (Pressure Loss of Piping)
h
LD27812
FIGURE 47 - STEAM AND DRAIN SYSTEM (OPEN EXAMPLE) WITH STEAM DRAIN CONTROL VALVE
FIGURE 48 - STEAM AND DRAIN SYSTEM WITH STEAM DRAIN CONTROL VALVE
JOHNSON CONTROLS100
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
TABLE 27 - HEAT SOURCE AND HOT WATER QUALITY CONTROL (MAXIMUM CONCENTRATIONS)
ELEMENT (1) (5)
HOT WATER SYSTEM HEAT SOURCE WATER SYSTEM TENDENCY(2)
CIRCULATING WATER
REPLENISH WATER
CIRCULATING WATER
(20°C OR LOWER)
REPLENISH WATER
CO
RR
OSI
ON
SCA
LE
FOR
MIN
G
STA
ND
AR
D IT
EMS
pH (25°C) 7.0~8.0 7.0~8.0 6.8~8.0 6.8~8.0Electric Conductivity (mS per m) (25°C)(µS per cm) (25°C)(1)
Max. 30 (Max. 300)
Max. 30 (Max. 300)
Max. 40 (Max. 400)
Max. 30 (Max. 300)
Chloride Ion (mgCl- per l)
Max. 30 Max. 30 Max. 50 Max. 50
Sulfulic Acid Ion (mgSO4
2ˉ per I)Max. 30 Max. 30 Max. 50 Max. 50
Acid Consumption (PH4.8) (mgCaCO3 per I)
Max. 50 Max. 50 Max. 50 Max. 50
Total Hardness (mgCaCO3 per I)
Max. 70 Max. 70 Max. 70 Max. 70
Calcium Hardness (mgCaCO3 per I)
Max. 50 Max. 50 Max. 50 Max. 50
Ionized Silica (mgSiO2 per I)
Max. 30 Max. 30 Max. 30 Max. 30
REF
EREN
CE
ITEM
S
Iron (mgFe per I)
Max. 1.0 Max. 0.3 Max. 1.0 Max. 0.3
Copper (mgCu per I)
Max. 0.3 Max. 0.1 Max. 0.1 Max. 0.1
Sulfurization Ion (mgS2ˉ per I)
NO IONS ALLOWED
Ammonium Ion (mgNH4
+ per I)Max. 1.0 Max. 1.0 Max. 1.0 Max. 1.0
Residual Chlorine (mgCI per I)
Max. 0.3 Max. 0.3 Max. 0.3 Max. 0.3
Free Carbonate Acid (mgCO2 per I)
Max. 4.0 Max. 4.0 Max. 4.0 Max. 4.0
Stability Index – – – –
3. When the water temperature is high (40°C or higher), corrosion develops noticeably. Especially when steel material which makes direct contact with water has no protective covering, provide a suitable corrosion-preventive measure, such as adding a corrosion-preventive agent or applying deaeration treatment.
4. The supply water and replenishment water must be tap water, industrial water, or ground water. Demineralized water, neutral water, and softened water should not be used.
5. The items shown above are representative factors in corrosion and scale formation.
NOTES: 1. The item names, their definitions, and units are based on JIS
K 0101. Units and figures in braces are those which were used formerly. They are shown here for reference purposes.
2. In the Tendency column, a white circle ( ) indicates that a par-ticular item is a factor in corrosion or scale formation.
JOHNSON CONTROLS 101
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
STORAGE METHOD OF THE HEAT PUMPIf the heat pump needs to be stored long-term, the stor-age method varies. A lot depends on the machine room temperature condition and the storage period. If the machine room temperature is below 0°C, drain off the heat source water, hot water, and the steam drain. Dry the tube interiors. Make sure all equipment installed in the heat source water, hot water, and the steam lines is completely dry.
Nitrogen gas pressurization inside the absorption heat-pump is required when the storage period exceeds 6 months. Contact your local Johnson Controls Service Center for more details.
The heat pump is not explosion proof. Highly flammable items, gas, or liquids should not be handled or stored near the heat pump. Failure to do this may result in explosion, injury, or damage to the equipment or building.
There are two storage methods available for the heat pump during off-season (winter) or plant suspension; the wet storage method and the dry storage method. (The wet storage method is available only where heat source water and hot water will not freeze.)
Each storage method has its own characteristics. Select the method to use based on the plant’s features and the storage period. Details follow.
WET STORAGE METHODThe wet storage method may be used when there is no concern about heat source water or hot water freezing in winter. Store the machine in a place where the ambi-ent temperature will remain higher than 0°C.
If it is likely that the temperature will drop below that, provide a heater for the machine. If a heater is not pos-sible, contact your local Johnson Controls service cen-ter for further information. For details on the wet stor-age method, see Table 28 on page 102.
The wet storage procedure is as follows if either the heat source water line or the hot water line is an open system:
1. Completely drain the water from the systems if it has deteriorated in quality.
2. Clean the water systems by passing clear water through them from a position higher than the heat pump.
9. Fill the water systems with clear water.
10. Circulate the clear water through the water pump for 30 minutes to one hour to clean it.
11. Drain the water.
12. Completely fill the water systems with clear water again.
13. Store the machine.
DRY STORAGE METHODThe dry storage method should be used if the heat source or hot water system may freeze in the winter or, if the heat source or hot water system has a lining tube. Do not simply drain the heat source or hot water and store the machine. This significantly increases the pos-sibility of corrosion of the heat transfer tube and rust. For details, see Table 29 on page 103.
The dry storage procedure is as follows if either the heat source water line or the hot water line is an open system:
1. Completely drain the water.
2. Clean the water systems by passing clear water through them from a position higher than the heat pump.
3. Fill the water systems with clear water.
4. Circulate the clear water through the water pump for 30 minutes to one hour to clean it.
5. Drain the water from each water or steam box.
6. Dry the interior of each water or steam box and the heat transfer tube.
7. Store the machine.
JOHNSON CONTROLS102
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
PRECAUTIONS AGAINST EXTERNAL DAMAGEAvoid storing the machine in a place that is easily ac-cessible or near a construction site. If this is unavoid-able, provide the machine with protection.
If it is not possible to protect the machine, fill the in-terior with N2 to minimize the amount of air leakage. For details, contact your local Johnson Controls ser-vice center.
TABLE 28 - WET STORAGE METHODPART STORAGE METHOD NOTES
Storage Period; less than 2 months
Heat source water line Fully filled with water
1. The manual valve on the purge piping should be completely closed (See Figure 43 on page 83.
2. The main supply valve supplying steam must be closed.
3. If the storage period exceeds 2 months, to avoid the growth of algae and bacteria that may corrode the tubes, add the appropriate chemicals to the water.
4. If the storage period exceeds 2 month, water inside the heat pump should be replaced monthly. In addi-tion, run the heat source water and hot water pumps periodically.
5. If the storage period exceeds 6 months, check the internal nitrogen pressure weekly. It needs to stay at 0.01~0.02 MPaG.
Hot water line Steam line
Vacuum Inside of shells
Storage Period; more than 2 months and less than 6 months
Heat source water system Fully filled with water
Hot water system
Steam line Pressurized with Nitrogen
(0.01~0.02 MPaG) Inside of shells Vacuum
Storage Period; more than 6 months
Heat source water system Fully filled with water
Hot water system
Steam line Dried and pressurized
with Nitrogen (0.01~0.02 MPaG)
Inside of shells Pressurized with Nitrogen
(0.01~0.02 MPaG)
JOHNSON CONTROLS 103
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
TABLE 29 - DRY STORAGE METHODPART STORAGE METHOD NOTES
Storage Period; less than 2 months
Heat source water system
Dried and pressurized with Nitrogen (0.01~0.02
MPaG)1. Heat source water and hot water systems should be
drained completely and dried by nitrogen blow. Then pressurize with nitrogen and leave as is. Depend-ing on the water quality, hard scale may be fixed on the inside surface of tubes by drying. It can be removed only by chemical cleaning. If the unit is be stored for more than one year, you must clean the tubes. Then, drain the unit, dry the inside by nitrogen blow,and pressurize it with nitrogen.
2. The main supply valve supplying steam must be closed.
3. If the storage period is longer than 6 months, apply pressure at 0.01~0.02 MPaG with nitrogen inside the shells and leave as is. Internal pressure should be checked at least once a week to confirm no pres-sure drop occurs.
4. The manual valve on the purge piping should be fully closed (See Figure 43 on page 83).
Hot water systemSteam line
VacuumInside of shell
Storage Period; more than 2 months and less than 6 months
Heat source water system Dried and pressurized
with Nitrogen (0.01~0.02 MPaG)
Hot water system Steam line
Inside of shells Vacuum
Storage Period; more than 6 months
Heat source water system Dried and pressurized
with Nitrogen (0.01~0.02 MPaG)
Hot water system Steam line
Inside of shells Pressurized with Nitrogen
(0.01~0.02 MPaG)
JOHNSON CONTROLS104
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
LD14221d
SATURATION PRESSURE m
m HgREFR
IGERANT
TEMPERATU
RE F
20 15 10 8 6 4.2
100
9080
70
60
50
40
30
995.
5
900
800
700
600
500
400
300
200
150
SOLU
TIO
N T
EMPE
RA
TUR
EF
70
80
60 50 40 3040
5060
7080
9010
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
0200
190
180
170
160
150
140
130
120
110
100
90 80 70 60 50 40 30220
210
90
100
110
120
130
140
150
160
170
180
190
200
210
220
CR
YSTA
LLIZ
ATI
ON
AR
EA65
%60
%55
%50
%45
%40
%
40%
45%
50%
55%
60%
65%
70%
200
200
210
210
220
220
230
230
240
240
250
250
260
260
270
270
280
280
290
290
300
300
310
310
320
320
330
330
340
340
350
350
Düh
ring
Dia
gram
/ PT
X C
hart
Abs
orpt
ion
Hea
t Pum
ps
Use
ful C
onve
rsio
n Fo
rmul
asTo
Con
vert
ºC (C
entig
rade
) to
ºF (F
ahre
nhei
t) or
ºF to
ºC:
ºC =
ºF
+40
1.8
-40
ºF =
(ºC
+ 4
0) x
1.8
- 40
1 at
m (a
tmos
pher
e at
sea
leve
l) =
14.6
96 p
sia
= 0
psig
= 7
60 m
mH
G =
29.
92 in
Hg
1 m
m H
g =
1000
mic
rons
= 0
.393
7 in
ch H
g =
.019
34 p
si1
in H
g =
25.4
mm
Hg
= .4
91 p
si1
psi =
2.0
36 in
Hg
= 51
.7 m
m H
g =
2.31
ft H
2O1
ft H
2O =
.433
psi
1 lb
= .4
536
Kg
= 45
3.6
gms
1 lit
er =
.264
1 U
.S. g
al =
1.0
57 U
.S. q
uarts
1 U
.S. g
allo
n =
3.78
5 lit
ers
1 in
ch =
25.
4 m
m1
ton
refri
gera
tion
(12,
000
btu/
hr) =
3.5
2 kW
FIGURE 49 - DUHRING DIAGRAM (PTX CHART (°F))
JOHNSON CONTROLS 105
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
FIGURE 50 - DUHRING DIAGRAM (PTX CHART (°C))
10.0
15.6
21.1
26.7
32.2
37.8
43.3
48.9
54.4
60.0
65.6
71.1
76.7
Use
ful
Con
vers
ion
Form
ulas
To c
onve
rt °C
(Cen
tigra
de) t
o °F
(Fah
renh
eit)
or °F
to °C
:
°C=
°F +
40
–40
°F =
(°C
+ 40
) x 1
.8 –
40
1.8
1 at
m (a
tmos
pher
e at
sea
leve
l) =
14.6
96 p
sia
= 0
psig
= 7
60 m
mH
g =
29.9
2 in
Hg
1 m
m H
g =
1000
mic
rons
= 0
.393
7 in
ch H
g =
.019
34 p
si
1 in
Hg
= 25
.4 m
m H
g =
.491
psi
1 ps
i = 2
.036
in H
g =
51.7
mm
Hg
= 2.
31 ft
H2O
1 ft
H2O
= .4
33 p
si
1 lb
= .4
536
Kg
= 45
3.6
gms
1 lit
er =
.264
1 U
.S. g
al =
1.0
57 U
.S. q
uarts
1 U
.S. g
allo
n =
3.78
5 lit
ers
1 in
ch =
25.
4 m
m
1 to
n re
frige
ratio
n (1
2,00
0 B
tu/h
r) =
3.5
2 kW
Duh
ring
Dia
gram
/PTX
Cha
rt
4.4
82.2
87.8
93.3
98.9
104.
411
0.0
115.
612
1.1
126.
713
2.2
137.
814
3.3
148.
915
4.4
160.
0
165.
617
1.1
176.
7-1
.1
4.4
10.0
15.6
21.1
26.7
32.2
37.8
43.3
48.9
54.4
60.0
65.6
71.1
76.7
82.2
87.8
93.3
98.9
104.
4
0.6
0.8
1.1
1.3
2.0
4.0
5.3
6.7
8.0
9.310
.712.013
.3
20.0
26.7
40.0
53.3
66.6
80.0
93.310
6.612
0.013
2.7
2.7
SOLU
TIO
N T
EMPE
RAT
UR
E °C
CRY
STA
LLIZ
ATIO
N A
REA
SATURATION PRESSURE kP
a
REFRIGERANT TEMPERATURE °C
93.3
98.9
104.
411
0.0
115.
612
1.1
126.
713
2.2
137.
814
3.3
148.
915
4.4
160.
0
165.
617
1.1
176.
7
40%
45%
50%
55%
60%
65%
40%
45%
50%
55%
60%
65%
70%
LC20933d
Abs
orpt
ion
Hea
t Pum
ps
JOHNSON CONTROLS106
SECTION 7 – MAINTENANCE FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
FIGURE 51 - SPECIFIC GRAVITY - CONCENTRATION (°F)LD14222d
6 65.70 65.85 66.00 66.14 66.2866.09 66.24 66.38 66.52 66.6766.47 66.61 66.76 66.90 67.0466.84 66.98 67.13 67.27 67.41
6 67.20 67.35 67.49 67.63 67.7767.56 67.70 67.84 67.98 68.12
SPECIFIC GRAVITY - CONCENTRATION TABLESAQUEOUS LiBr SOLUTIONSRefrigerant Table (%LiBr by Weight)
Temperature F
S.G. 40 45 50 55 60 65 70 75 80 85 90 95 1001.00 –– –– –– –– –– –– 0.08 0.18 0.28 0.37 0.47 0.57 0.671.01 0.98 1.08 1.17 1.27 1.37 1.47 1.56 1.66 1.76 1.85 1.95 2.05 2.151.02 2.43 2.52 2.62 2.72 2.82 2.91 3.01 3.11 3.20 3.30 3.40 3.50 3.591.03 3.84 3.94 4.03 4.13 4.23 4.33 4.42 4.52 4.62 4.72 4.81 4.91 5.011.04 5.22 5.32 5.42 5.51 5.61 5.71 5.81 5.90 6.00 6.10 6.19 6.29 6.391.05 6.57 6.67 6.77 6.87 6.96 7.06 7.16 7.26 7.35 7.45 7.55 7.64 7.74
Solution TablesTemperature F
S.G 60 70 80 90 100 110 120 130 140 150 160 170 1801.350 37.27 37.5 37.75 37.98 38.21 38.44 38.67 38.90 39.13 39.35 39.58 39.80 40.021.360 38.03 38.26 38.50 38.73 38.96 39.19 39.42 39.64 39.87 40.09 40.31 40.53 40.751.370 38.78 39.01 39.24 39.47 39.70 39.93 40.15 40.38 40.60 40.82 41.04 41.26 41.481.380 39.52 39.75 39.98 40.20 40.43 40.66 40.88 41.10 41.32 41.54 41.76 41.98 42.201.390 40.25 40.48 40.70 40.93 41.16 41.38 41.60 41.82 42.04 42.26 42.48 42.69 42.901.400 40.97 41.20 41.42 41.65 41.87 42.09 42.31 42.53 42.75 42.97 43.18 43.39 43.611.410 41.69 41.91 42.14 42.36 42.58 42.80 43.02 43.24 43.45 43.67 43.88 44.09 44.301.420 42.39 42.62 42.84 43.06 43.28 43.50 43.72 43.93 44.15 44.36 44.57 44.78 44.991.430 43.10 43.32 43.54 43.76 43.98 44.19 44.41 44.62 44.83 45.04 45.25 45.46 45.671.440 43.79 44.01 44.23 44.45 44.66 44.88 45.09 45.30 45.51 45.72 45.93 46.13 46.341.450 44.47 44.69 44.91 45.13 45.34 45.55 45.76 45.97 46.18 46.39 46.59 46.80 47.001.460 45.15 45.37 45.58 45.80 46.01 46.22 46.43 46.6 446.85 47.05 47.25 47.46 47.661.470 45.82 46.03 46.25 46.46 46.67 46.88 47.09 47.30 47.50 47.70 47.91 48.11 48.301.480 46.48 46.69 46.91 47.12 47.33 47.54 47.74 47.95 48.15 48.35 48.55 48.75 48.941.490 47.13 47.35 47.56 47.77 47.97 48.18 48.38 48.59 48.79 48.99 49.19 49.38 49.581.500 47.78 47.99 48.20 48.41 48.61 48.82 49.02 49.22 49.42 49.62 49.82 50.01 50.201.510 48.42 48.63 48.84 49.04 49.25 49.45 49.65 49.85 50.05 50.24 50.44 50.63 50.821.520 49.05 49.26 49.46 49.67 49.87 50.07 50.27 50.47 50.66 50.86 51.05 51.24 51.431.530 49.67 49.88 50.08 50.28 50.49 50.68 50.88 51.08 51.27 51.46 51.66 51.84 52.031.540 50.29 50.49 50.69 50.89 51.09 51.29 51.49 51.68 51.87 52.06 52.25 52.44 52.631.550 50.89 51.10 51.30 51.50 51.69 51.89 52.08 52.28 52.47 52.66 52.84 53.03 53.211.560 51.49 51.69 51.89 52.09 52.29 52.48 52.67 52.86 53.05 53.24 53.43 53.61 53.791.570 52.09 52.28 52.48 52.68 52.87 53.06 53.25 53.44 53.6 353.82 54.00 54.18 54.371.580 52.67 52.87 53.06 53.26 53.45 53.64 53.83 54.02 54.20 54.39 54.57 54.75 54.931.590 53.25 53.44 53.64 53.83 54.02 54.21 54.39 54.58 54.77 54.95 55.13 55.31 55.491.600 53.81 54.01 54.20 54.39 54.58 54.77 54.95 55.14 55.32 55.50 55.68 55.86 56.041.610 54.37 54.57 54.76 54.95 55.13 55.32 55.50 55.69 55.87 56.05 56.23 56.40 56.581.620 54.93 55.12 55.31 55.49 55.68 55.86 56.05 56.23 56.41 56.59 56.76 56.94 57.111.630 55.47 55.66 55.85 56.03 56.22 56.40 56.58 56.76 56.94 57.12 57.29 57.46 57.641.640 56.01 56.20 56.38 56.57 56.75 56.93 57.11 57.29 57.46 57.64 57.81 57.98 58.151.650 56.54 56.72 56.91 57.09 57.27 57.45 57.63 57.81 57.98 58.15 58.33 58.50 58.671.660 57.06 57.25 57.43 57.61 57.79 57.97 58.14 58.32 58.49 58.66 58.83 59.00 59.171.670 57.58 57.76 57.94 58.12 58.29 58.47 58.65 58.82 58.99 59.16 59.33 59.50 59.661.680 58.08 58.26 58.44 58.62 58.79 58.97 59.14 59.31 59.48 59.65 59.82 59.99 60.151.690 58.58 58.76 58.94 59.11 59.29 59.46 59.63 59.80 59.97 60.14 60.30 60.47 60.631.700 59.07 59.25 59.42 59.60 59.77 59.94 60.11 60.28 60.45 60.61 60.78 60.94 61.101.710 59.55 59.73 59.90 60.08 60.25 60.42 60.59 60.75 60.92 61.08 61.25 61.41 61.571.720 60.20 60.38 60.55 60.72 60.88 61.05 61.22 61.38 61.54 61.71 61.87 62.031.730 60.67 60.84 61.01 61.18 61.34 61.51 61.67 61.84 62.00 62.16 62.32 62.481.740 61.13 61.30 61.46 61.63 61.80 61.96 62.12 62.28 62.44 62.60 62.76 62.921.750 61.74 61.91 62.08 62.24 62.40 62.56 62.72 62.88 63.04 63.20 63.351.760 62.35 62.51 62.68 62.84 63.00 63.16 63.31 63.47 63.62 63.781.770 62.78 62.94 63.10 63.26 63.42 63.58 63.74 63.89 64.04 64.201.780 63.37 63.52 63.68 63.84 64.00 64.15 64.30 64.46 64.611.790 63.78 63.94 64.09 64.25 64.40 64.56 64.71 64.86 65.011.800 64.34 64.50 64.65 64.81 64.96 65.11 65.26 65.411.810 64.89 65.05 65.20 65.35 65.50 65.65 65.801.820 65.43 65.58 65.73 65.88 66.03 66.181.830 65.96 66.11 66.26 66.41 66.551.840 66.48 66.63 66.77 66.921.850 66.99 67.13 67.27
190 200 210 220 230 240 40.24 40.46 40.68 40.90 41.11 41.33 40.97 41.19 41.41 41.62 41.83 42.0541.69 41.91 42.12 42.34 42.55 42.7642.41 42.62 42.83 43.04 43.25 43.4643.12 43.33 43.54 43.75 43.95 44.1643.82 44.03 44.23 44.44 44.64 44.85 44.51 44.72 44.92 45.12 45.33 45.5345.19 45.40 45.60 45.80 46.00 46.2045.87 46.07 46.27 46.47 46.67 46.8746.54 46.74 46.94 47.14 47.33 47.5347.20 47.40 47.60 47.79 47.99 48.18 47.85 48.05 48.25 48.44 48.63 48.8248.50 48.70 48.89 49.08 49.27 49.4649.14 49.33 49.52 49.71 49.90 50.0949.77 49.96 50.15 50.34 50.53 50.7150.39 50.58 50.77 50.96 51.14 51.3351.01 51.20 51.38 51.57 51.75 51.93 51.62 51.80 51.99 52.17 52.35 52.5352.22 52.40 52.59 52.77 52.95 53.1252.81 52.99 53.18 53.36 53.53 53.7153.40 53.58 53.76 53.94 54.11 54.2953.97 54.15 54.33 54.51 54.68 54.8654.55 54.72 54.90 55.07 55.25 55.42 55.11 55.28 55.46 55.63 55.80 55.9755.66 55.84 56.01 56.18 56.35 56.5256.21 56.38 56.55 56.72 56.89 57.0656.75 56.92 57.09 57.26 57.43 57.5957.28 57.45 57.62 57.79 57.95 58.1257.81 57.97 58.14 58.31 58.47 58.6358.32 58.49 58.66 58.82 58.98 59.1458.83 59.00 59.16 59.32 59.49 59.6559.33 59.50 59.66 59.82 59.98 60.1459.83 59.99 60.15 60.31 60.47 60.6360.31 60.48 60.64 60.79 60.95 61.1160.79 60.95 61.11 61.27 61.43 61.5861.26 61.42 61.58 61.74 61.89 62.0561.73 61.89 62.04 62.20 62.35 62.5062.18 62.34 62.50 62.65 62.80 62.9562.63 62.79 62.94 63.09 63.25 63.4063.07 63.23 63.38 63.53 63.68 63.8363.51 63.66 63.81 63.96 64.11 64.2663.93 64.08 64.23 64.38 64.53 64.6864.35 64.50 64.65 64.80 64.95 65.0964.76 64.91 65.06 65.21 65.35 65.5065.16 65.31 65.46 65.60 65.75 65.8965.565.94 66.32 66.70 67.067.42
CRYSTALLIZATION AREA
JOHNSON CONTROLS 107
SECTION 7 – MAINTENANCEFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
7
FIGURE 52 - SPECIFIC GRAVITY - CONCENTRATION (°C)
SPECIFIC GRAVITY – CONCENTRATION TABLES AQUEOUS LiBr SOLUTIONS
Refrigerant Table (%LiBr by Weight) Temperature °C
S.G. 4.4 7.2 10.0 12.8 15.6 18.3 21.1 23.9 26.7 29.4 32.2 35.0 37.8 1.00 0.08 0.18 0.28 0.37 0.47 0.57 0.67 1.01 0.98 1.08 1.17 1.27 1.37 1.47 1.56 1.66 1.76 1.85 1.95 2.05 2.15 1.02 2.43 2.52 2.62 2.72 2.82 2.91 3.01 3.11 3.2 3.3 3.4 3.5 3.59 1.03 3.84 3.94 4.03 4.13 4.23 4.33 4.42 4.52 4.62 4.72 4.81 4.91 5.01 1.04 5.22 5.32 5.42 5.51 5.61 5.71 5.81 5.9 6 6.1 6.19 6.29 6.39 1.05 6.57 6.67 6.77 6.87 6.96 7.06 7.16 7.26 7.35 7.45 7.55 7.64 7.74
Solution Tables Temperature °C
S.G. 15.6 21.1 26.7 32.2 37.8 43.3 48.9 54.4 60.0 65.6 71.1 76.7 82.2 87.8 93.3 98.9 104.4 110.0 115.6 1.35 37.27 37.50 37.75 37.98 38.21 38.44 38.67 38.90 39.13 39.35 39.58 39.80 40.02 40.24 40.46 40.68 40.90 41.11 41.33 1.36 38.03 38.26 38.50 38.73 38.96 39.19 39.42 39.64 39.87 40.09 40.31 40.53 40.75 40.97 41.19 41.41 41.62 41.83 42.05 1.37 38.78 39.01 39.24 39.47 39.70 39.93 40.15 40.38 40.60 40.82 41.04 41.26 41.48 41.69 41.91 42.12 42.34 42.55 42.76 1.38 39.52 39.75 39.98 40.20 40.43 40.66 40.88 41.10 41.32 41.54 41.76 41.98 42.20 42.41 42.62 42.83 43.04 43.25 43.46 1.39 40.25 40.48 40.70 40.93 41.16 41.38 41.60 41.82 42.04 42.26 42.48 42.69 42.90 43.12 43.33 43.54 43.75 43.95 44.16 1.40 40.97 41.20 41.42 41.65 41.87 42.09 42.31 42.53 42.75 42.97 43.18 43.39 43.61 43.82 44.03 44.23 44.44 44.64 44.85 1.41 41.69 41.91 42.14 42.36 42.58 42.80 43.02 43.24 43.45 43.67 43.88 44.09 44.30 44.51 44.72 44.92 45.12 45.33 45.53 1.42 42.39 42.62 42.84 43.06 43.28 43.50 43.72 43.93 44.15 44.36 44.57 44.78 44.99 45.19 45.40 45.60 45.80 46.00 46.20 1.43 43.10 43.32 43.54 43.76 43.98 44.19 44.41 44.62 44.83 45.04 45.25 45.46 45.67 45.87 46.07 46.27 46.47 46.67 46.87 1.44 43.79 44.01 44.23 44.45 44.66 44.88 45.09 45.30 45.51 45.72 45.93 46.13 46.34 46.54 46.74 46.94 47.14 47.33 47.53 1.45 44.47 44.69 44.91 45.13 45.34 45.55 45.76 45.97 46.18 46.39 46.59 46.80 47.00 47.20 47.40 47.60 47.79 47.99 48.18 1.46 45.15 45.37 45.58 45.80 46.01 46.22 46.43 46.60 46.85 47.05 47.25 47.46 47.66 47.85 48.05 48.25 48.44 48.63 48.82 1.47 45.82 46.03 46.25 46.46 46.67 46.88 47.09 47.30 47.50 47.70 47.91 48.11 48.30 48.50 48.70 48.89 49.08 49.27 49.46 1.48 46.48 46.69 46.91 47.12 47.33 47.54 47.74 47.95 48.15 48.35 48.55 48.75 48.94 49.14 49.33 49.52 49.71 49.90 50.09 1.49 47.13 47.35 47.56 47.77 47.97 48.18 48.38 48.59 48.79 48.99 49.19 49.38 49.58 49.77 49.96 50.15 50.34 50.53 50.71 1.50 47.78 47.99 48.20 48.41 48.61 48.82 49.02 49.22 49.42 49.62 49.82 50.01 50.20 50.39 50.58 50.77 50.96 51.14 51.33 1.51 48.42 48.63 48.84 49.04 49.25 49.45 49.65 49.85 50.05 50.24 50.44 50.63 50.82 51.01 51.20 51.38 51.57 51.75 51.93 1.52 49.05 49.26 49.46 49.67 49.87 50.07 50.27 50.47 50.66 50.86 51.05 51.24 51.43 51.62 51.80 51.99 52.17 52.35 52.53 1.53 49.67 49.88 50.08 50.28 50.49 50.68 50.88 51.08 51.27 51.46 51.66 51.84 52.03 52.22 52.40 52.59 52.77 52.95 53.12 1.54 50.29 50.49 50.69 50.89 51.09 51.29 51.49 51.68 51.87 52.06 52.25 52.44 52.63 52.81 52.99 53.18 53.36 53.53 53.71 1.55 50.89 51.10 51.30 51.50 51.69 51.89 52.08 52.28 52.47 52.66 52.84 53.03 53.21 53.40 53.58 53.76 53.94 54.11 54.29 1.56 51.49 51.69 51.89 52.09 52.29 52.48 52.67 52.86 53.05 53.24 53.43 53.61 53.79 53.97 54.15 54.33 54.51 54.68 54.86 1.57 52.09 52.28 52.48 52.68 52.87 53.06 53.25 53.44 53.60 53.82 54.00 54.18 54.37 54.55 54.72 54.90 55.07 55.25 55.42 1.58 52.67 52.87 53.06 53.26 53.45 53.64 53.83 54.02 54.20 54.39 54.57 54.75 54.93 55.11 55.28 55.46 55.63 55.80 55.97 1.59 53.25 53.44 53.64 53.83 54.02 54.21 54.39 54.58 54.77 54.95 55.13 55.31 55.49 55.66 55.84 56.01 56.18 56.35 56.52 1.60 53.81 54.01 54.20 54.39 54.58 54.77 54.95 55.14 55.32 55.50 55.68 55.86 56.04 56.21 56.38 56.55 56.72 56.89 57.06 1.61 54.37 54.57 54.76 54.95 55.13 55.32 55.50 55.69 55.87 56.05 56.23 56.40 56.58 56.75 56.92 57.09 57.26 57.43 57.59 1.62 54.93 55.12 55.31 55.49 55.68 55.86 56.05 56.23 56.41 56.59 56.76 56.94 57.11 57.28 57.45 57.62 57.79 57.95 58.12 1.63 55.47 55.66 55.85 56.03 56.22 56.40 56.58 56.76 56.94 57.12 57.29 57.46 57.64 57.81 57.97 58.14 58.31 58.47 58.63 1.64 56.01 56.20 56.38 56.57 56.75 56.93 57.11 57.29 57.46 57.64 57.81 57.98 58.15 58.32 58.49 58.66 58.82 58.98 59.14 1.65 56.54 56.72 56.91 57.09 57.27 57.45 57.63 57.81 57.98 58.15 58.33 58.50 58.67 58.83 59.00 59.16 59.32 59.49 59.65 1.66 57.06 57.25 57.43 57.61 57.79 57.97 58.14 58.32 58.49 58.66 58.83 59.00 59.17 59.33 59.50 59.66 59.82 59.98 60.14 1.67 57.58 57.76 57.94 58.12 58.29 58.47 58.65 58.82 58.99 59.16 59.33 59.50 59.66 59.83 59.99 60.15 60.31 60.47 60.63 1.68 58.08 58.26 58.44 58.62 58.79 58.97 59.14 59.31 59.48 59.65 59.82 59.99 60.15 60.31 60.48 60.64 60.79 60.95 61.11 1.69 58.58 58.76 58.94 59.11 59.29 59.46 59.63 59.80 59.97 60.14 60.30 60.47 60.63 60.79 60.95 61.11 61.27 61.43 61.58 1.70 59.07 59.25 59.42 59.60 59.77 59.94 60.11 60.28 60.45 60.61 60.78 60.94 61.10 61.26 61.42 61.58 61.74 61.89 62.05 1.71 59.55 59.73 59.90 60.08 60.25 60.42 60.59 60.75 60.92 61.08 61.25 61.41 61.57 61.73 61.89 62.04 62.20 62.35 62.50 1.72
60.20 60.38 60.55 60.72 60.88 61.05 61.22 61.38 61.54 61.71 61.87 62.03 62.18 62.34 62.50 62.65 62.80 62.95 1.73 60.67 60.84 61.01 61.18 61.34 61.51 61.67 61.84 62.00 62.16 62.32 62.48 62.63 62.79 62.94 63.09 63.25 63.40 1.74 61.13 61.30 61.46 61.63 61.80 61.96 62.12 62.28 62.44 62.60 62.76 62.92 63.07 63.23 63.38 63.53 63.68 63.83 1.75
61.74 61.91 62.08 62.24 62.40 62.56 62.72 62.88 63.04 63.20 63.35 63.51 63.66 63.81 63.96 64.11 64.26 1.76
62.35 62.51 62.68 62.84 63.00 63.16 63.31 63.47 63.62 63.78 63.93 64.08 64.23 64.38 64.53 64.68 1.77 62.78 62.94 63.10 63.26 63.42 63.58 63.74 63.89 64.04 64.20 64.35 64.50 64.65 64.80 64.95 65.09 1.78
63.37 63.52 63.68 63.84 64.00 64.15 64.30 64.46 64.61 64.76 64.91 65.06 65.21 65.35 65.50 1.79 63.78 63.94 64.09 64.25 64.40 64.56 64.71 64.86 65.01 65.16 65.31 65.46 65.60 65.75 65.89 1.80
64.34 64.50 64.65 64.81 64.96 65.11 65.26 65.41 65.56 65.70 65.85 66.00 66.14 66.28 1.81
64.89 65.05 65.20 65.35 65.50 65.65 65.80 65.94 66.09 66.24 66.38 66.52 66.67 1.82
65.43 65.58 65.73 65.88 66.03 66.18 66.32 66.47 66.61 66.76 66.90 67.04 1.83
65.96 66.11 66.26 66.41 66.55 66.70 66.84 66.98 67.13 67.27 67.41 1.84
66.48 66.63 66.77 66.92 67.06 67.20 67.35 67.49 67.63 67.77
1.85 66.99 67.13 67.27 67.42 67.56 67.70 67.84 67.98 68.12
CRYSTALLIZATON AREA
JOHNSON CONTROLS108
SECTION 8 – TROUBLESHOOTING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
SECTION 8 – TROUBLESHOOTING
If the heat pump has a problem or an abnormal condi-tion while it operates, find the cause. Use the proce-dures listed below to fix the problem.
If the cause is not clear, using the countermeasure does not fix the problem, or if the heat pump seems to have a serious problem, contact your local Johnson Controls Service Center immediately.
If the heat pump stops because of a problem, wait until the heat source water pump, hot water pump, and heat pump unit stop completely, then review and verify the following items.
Several items should be checked routinely whenever the heat pump experiences any trouble or abnormality:
• Check to see if the main steam valve was closed by mistake.
• Open the main valve.
• See if the valves of the heat source water system and the hot water system are set correctly. Verify the flow rate.
Contact your local Johnson Controls Service Center if any of the following apply:
• The water flow rate setting is unknown.
• It takes 30 minutes or more to restore operations.
• Solution is crystallized.
• The cause of the trouble is not readily apparent.
Check the causes in order. Any of these causes will start the diluting operation automatically then stop the heat pump. Check that the diluting operation was completed, and if not, dilute the solution. See the Manual Refrigerant Blowdown and Diluting Method on page 88 .
JOHNSON CONTROLS 109
SECTION 8 – TROUBLESHOOTINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
8
TABLE 30 - GENERATOR HIGH TEMPERATURE, GENERATOR HIGH PRESSUREITEM CAUSE COUNTERMEASURE
1 Hot water flow is low or flow has stopped.
• Check the flow meter, discharge pressure of the hot water pump, current, etc. • If the flow rate is low, check the opening ratio of the flow control valve.• Check to see if the strainer is clogged.
2Pressure or flow rate of steam exceeds the specification value
• Check and change, if necessary, the boiler's pressure setting point so that it matches the specification.
• Check and adjust the back pressure of the steam drain line during operation under the condition close to the specification, so that it matches the specification.
2 Non-condensable gas stays in the machine.
• Check the capacity of the vacuum pump. • Check the purge unit.• Purge non-condensable gas from the heat pump (See Purge Procedure on page
81). • If partial load operation is continued for a long period, non-condensable gas tends
to stay in the absorber. In this case, purge directly from the low pressure side (according to instructions in Purge Procedure on page 81.
4Heat exchange tube is dirty (heat source water, hot water).
Contact your local Johnson Controls Service Office. 5 Solution is crystallized.6 Corrosion inhibitor is worn.
7 Air leaks in absorption heat pump.
TABLE 31 - REFRIGERANT OVERCOOLED, SOURCE WATER OVERCOOLED
When the refrigerant or the heat source water is over-cooled, the heat pump stops immediately. It does NOT perform the dilution operation. When this happens, the solution may crystallize in 4-5 hours. Perform the Manual Refrigerant Blowdown and Diluting Method on page 88.
ITEM CAUSE COUNTERMEASURE
1Heat source water flow rate drops or changes drastically.
See if the heat source water flow rate changes drastically (particularly in the case of variable flow rate specification). If it changes, limit the change rate to the heat source water flow control or take another measure.
2Load of heat source water side drops too far or too quickly.
See if the load of the heat source water side changes drastically.
3 Refrigerant is dirty (contains solution).
See if the refrigerant refining operation has been performed periodically. For the refrigerant refining method, see the procedure shown Refrigerant Refining Method on page 88.
4 Heat exchange tube is dirty (Heat source water)
Contact your local Johnson Controls Service Office.5 Temperature controller is
broken.
JOHNSON CONTROLS110
SECTION 8 – TROUBLESHOOTING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
TABLE 32 - SOURCE WATER SUSPENSION
When heat source water flow stops, the absorption heat pump also stops immediately. It does NOT perform the dilution operation. If the absorption heat pump is left as it is, the solution in it may be crystallized in 4-5 hours. To prevent this, dilute the solution according to manual refrigerant blowing and diluting method. See Manual Refrigerant Blowdown and Diluting Method on page 88 for more information.
ITEM CAUSE COUNTERMEASURE
1 Heat source water pump has a problem.
Check the heat source water pump for a problem.
2 Heat source water flow rate is low.
• Check to see if the heat source water flow rate is below the set point of the water suspension switch.
• If it is low, check the flow controller, check the strainer for clogging, and check the opening ratio of the flow control valve.
3Pressure transfer pipe of water suspension switch is clogged. Contact your local Johnson Controls Service Office.
4 Water suspension switch is broken.
TABLE 33 - PUMPS ABNORMAL
If the heat pump has a pump problem, it stops imme-diately and does NOT perform the dilution operation. If left as it is, the solution in it may be crystallized in 4-5 hours. To prevent this, contact your local Johnson Controls Service Office immediately.
ITEM CAUSE COUNTERMEASURE1 Bearings of the pump are worn or clogged.
Contact your local Johnson Controls Service Office.
2 Pump is damaged by cavitation caused by low liquid level.3 Thermal switch is not set properly.4 Internal cycle control valve is not set properly.5 Filter in the pump is clogged.6 Solution is crystallized.7 Circuit breaker has tripped.8 Inverter has a problem (Inverter equipped model only)
JOHNSON CONTROLS 111
SECTION 8 – TROUBLESHOOTINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
8
TROUBLESHOOTING PERFORMANCE ISSUESIf the performance is low while the steam control valve is open or if the steam control valve does not com-pletely open while the load is sufficient, check num-bers 1-7 in the following table in order. If the cause of the trouble is not 1-7, it may be 8-14. If that is the case, contact your local Johnson Controls Service Cen-ter immediately.
TABLE 34 - TROUBLESHOOTING PERFORMANCE ISSUES
ITEM CAUSE COUNTERMEASURE
1 Pressure or flow rate of steam is below specifications
• Check and change the boiler's pressure set point so that it matches the specification.
• Check and adjust the back pressure of the steam drain line during operation so that it matches the specification.
2 Hot water flow rate is low.
• See if the hot water supply rate matches the specification. (Check the flow meter, discharge pressure of the hot water pump, current, etc.)
• If the flow rate is low, check the opening ratio of the flow controller valve and check the strainer for clogging.
3 Hot water heat exchange tube is dirty. Contact your local Johnson Controls Service Office.
4 Non-condensable gas remains in machine.
• See Purge Procedure on page 81. • Check the capacity of the vacuum pump. • Check the purge unit for trouble. • Purge non-condensable gas from the absorption heat pump. If
partial-load operation continues for a long time, non-condensable gas tends to stay in the absorber. In this case, purge directly from the low-pressure side (absorber). See Purge Procedure on page 81.
• Even if the automatic purge unit is installed, purge from the lower pressure side (absorber) manually.
5 Temperature controllers are not set properlyBe sure that each setting parameter for temperature control is set correctly.
6 Manual refrigerant blow valves are kept open. Check that the manual refrigerant blow valve VR1 is closed.7 Refrigerant Pump Stop button is lit. Press the Refrigerant Pump Auto button.8 Corrosion inhibitor is depleted.
Contact your local Johnson Controls Service Office.
9 Surface active agent is depleted.10 Refrigerant is dirty (contains solution).11 Temperature controllers are broken12 Internal cycle control valve is not set properly.13 Solution is crystallized.14 Air leaks in absorption heat pump.
JOHNSON CONTROLS112
SECTION 8 – TROUBLESHOOTING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
VACUUM PUMPIf the vacuum level of the purge line did not reach the specified level during the vacuum pump performance check, the entire purge line needs to be inspected. See the table below. If the vacuum pump needs to be dis-assembled for inspection, contact your local Johnson Controls Service Center.
TABLE 35 - VACUUM PUMP TROUBLESHOOTINGITEM CAUSE COUNTERMEASURE
1 Deterioration of vacuum pump oil Replace the vacuum pump oil.2 Wrong operation of purging line switching when
vacuum pump capacity was checked.See Purge Procedure on page 81. Confirm the valves are open or closed.
3 Deterioration of vacuum pump beltContact your local Johnson Controls Service Center.4 Leakage in purge pipe lines.
5 Thermal switch is not set properly
WATER JET PURGE SYSTEMWhen the Purge Abnormal alarm button lights, the entire of the water jet purge line needs to be inspected. See the table below.
TABLE 36 - WATER JET PURGE TROUBLE SHOOTING
ITEM CAUSE COUNTERMEASURE1 Water jet service valves are closed Open all of the water jet service valves.2 Water discharge hose from water jet purge system
is cloggedClean inside the water discharge hose
3 Water jet solenoid valves do not work properly
Contact your local Johnson Controls Service Center.
4 Aspirator for water jet purge does not work properly
5 Level switch for separator does not work properly6 Discharged water line between evaporator and
aspirator is clogged7 Gas line between purge tank and aspirator is
clogged
JOHNSON CONTROLS 113
SECTION 8 – TROUBLESHOOTINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
8
ABNORMAL SOLUTION AND REFRIGERANT LEVELSCauses of abnormal levels of solution and re-frigerant and countermeasures against them If the level of the solution or refrigerant is wrong, correct it using the following procedure.
TABLE 37 - ABNORMAL REFRIGERANT AND SOLUTION LEVELS
SECTION NORMAL CONDITION
ABNORMAL CONDITION CAUSE COUNTERMEASURE
Refrigerant Overflow (G1)
High temperature of hot water inlet temperature. • See if the hot water supply rate conforms to the
specification. (Check the flow meter, discharge pressure of the hot water pump, current, etc.)
• If the flow rate is low, check the opening ratio of the flow controller valve and check the strainer for clogging.
• See Purge Procedure on page 81. Check the performance of the vacuum pump. Check the purge unit for trouble. Then, purge non-condensable gas from the absorption heat pump.
• If partial-load operation continues for a long time, non-condensable gas tends to stay in the absorber. In this case, purge directly from the low pressure side (absorber). See Purge Procedure on page 81.
Low temperature of heat source water outlet temperature.Pressure or flow rate of steam exceeds specifications
Hot water tube fouling
Purge trouble
Air leakage
Refrigerant Tank (G2)
Hot water inlet temperature is low. Set point error of automatic start or stop switch.
• Check the hot water inlet temperature • Check the setpoint.
Solution Tank (G3)
Purging is insufficient. See Purge Procedure on page 81.Valve opening setting error.
Contact your local Johnson Controls Service Center.Solution is crystallized.
LOW VACUUM LEVELSCauses of low vacuum level of purging line and coun-termeasures against them.
TABLE 38 - LOW VACUUM LEVELSITEM CAUSE COUNTERMEASURE
1 Purge pump trouble Contact your local Johnson Controls Service Office.2 Deterioration of vacuum pump oil. Replace the vacuum pump oil.
3 Wrong operation of purging line switching when vacuum pump capacity was checked. See Purge Procedure on page 81. Then, confirm if the
valves are open or closed on the purge line.4 Valve VP7 left open by mistake5 Deterioration of vacuum pump belt.
Contact your local Johnson Controls Service Office.6 Leakage in purge pipe line.
JOHNSON CONTROLS114
SECTION 8 – TROUBLESHOOTING FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Emergency Stop
Generator pressure lower than dilution finish pressure?
Heat source water or refrigerant temp low cut-out
alarm?
Dilution operation time has passed?.
Steam control valve or steam drain control
valve closed
• Heat source water suspension
• Refrigerant overcooled• Solution circulation pump
abnormal• Solution spray pump
abnormal• Refrigerant pump abnormal• Solution pump inverter
abnormal - Optional• Source water overcooled
Alarm Buzzer
No
• Hot water pump operation interlock• Heat source water pump operation
interlock• Interlock monitored normally• Hot water high temperature• Generator high temperature• Generator high pressure• Control sensor abnormal• CPU abnormal
No
Yes
No
Failure Light
Stop with dilution operation?
Dilution operation time calculation
Heat source water or hot water pump stop
Dilution operation time integration
Steam drain solenoid valve and steam shut off valve close (option)
Solution pump and refrigerant pump stop
Solution refrigerant pump stop
AH, FCU, stop
1
Dilution operation more than 30 minutes?
Dilution operation time integration stop
Solution refrigerant pump continues to
operate
1
External Outlet Issues
YesYes
Dilution finish
Reset operation (Buzzer off)
FIGURE 53 - TROUBLESHOOTING SEQUENCE FLOW CHART
Yes
No
NoYes
JOHNSON CONTROLS 115
SECTION 8 – TROUBLESHOOTINGFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
8
ACTIONS TO TAKE AGAINST POWER FAILUREIf the main power fails, take the following actions.
Power failure
Power failure interval is shorter than the controller back up interval
Power failure interval is shorter than 5 minutes
Power failure interval is shorter than 1 hour.
Continue running machine
Re-start using the Control Panel located on the machine. Monitor until machine returns to normal operation. Purge directly from the absorber. Stop the machine to ensure the dilution operation takes place. The dilution operation takes approximately 10 minutes.
Power is restored
Heat pump stops
No
If the power is not restored within 4-5 hours, the solution in the machine may be crystallized. Contact your local Johnson Controls Service Office for assistance.
Re-start using the Control Panel located on the machine. Monitor until machine returns to normal operation. Purge directly from the absorber.
No
Yes
Yes
No
Yes
FIGURE 54 - ACTIONS TO TAKE AGAINST POWER FAILURE
JOHNSON CONTROLS116
SECTION 9 - DECOMMISSIONING, DISMANTLING, AND DISPOSAL FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
SECTION 9 - DECOMMISSIONING, DISMANTLING, AND DISPOSAL
Unless otherwise indicated, the operations described below can be performed by any properly trained main-tenance technician.
1. Isolate all sources of electrical supply to the unit, including any control system supplies switched by the unit. Make sure that all points of isolation are secured in the off position.
2. Disconnect and remove the supply cables. For connection points, see SECTION 3 – HANDLING, STORAGE, INSTALLATION AND REASSEMBLY
3. Fill the interior of the unit with N2 gas to pressur-ize up to approximately 0.01~0.02 MPa.G.
4. Prepare a suitable container. As for the amounts of the charged solution and refrigerant in the ma-chine, see the name plate of the machine or con-tact your local Johnson Controls Service Center.
5. Drain the remainder of the solution and refriger-ant in the unit from each service valve as com-pletely as possible into the container.
6. Dispose of them in a suitable and safe manner
7. Isolate the unit heat exchanger from the external water systems. Drain the heat exchanger section of the system. If no isolation valves are installed it may be necessary to drain the complete system.
8. If glycol was used in the water system, or chemi-cal additives are contained, dispose of the solu-tion in a suitable and safe manner. Under NO cir-cumstances should any system containing glycol be drained directly into domestic waste or natural water systems.
9. After draining, disconnect and remove the water.
10. Remove fixing down bolts.
11. Lift the unit from position, using the points pro-vided and equipment with adequate lifting capac-ity.
See SECTION 3 – HANDLING, STORAGE, INSTAL-LATION AND REASSEMBLY for unit installation in-structions.
Units which cannot be removed in one piece after dis-connection, must be dismantled in position. Handle each component carefully. Where possible, dismantle units in the reverse order of installation.
Make sure that while components are being removed, the remaining parts are supported in a safe manner.
Only use lifting equipment of adequate capacity.
After removing the unit from position, dispose of the unit parts according to local laws and regulations.
JOHNSON CONTROLS 117
SECTION 9 - DECOMMISSIONING, DISMANTLING, AND DISPOSALFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
9THIS PAGE INTENTIONALLY LEFT BLANK.
JOHNSON CONTROLS118
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 1 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
Applicant: Hebei Molor Environmental Protection Technology Co.,Ltd.Address: No.5, Ganjiang Road, Shijiazhuang Economic and Technological Development Zone, Hebei
Sample information:Sample name: Lithium bromide solutionModel: /Applicant sheet received date: March 2, 2018Edit period: From March 2, 2018 to March 4, 2018
Required service : As specified by the client, to edit Safety Data Sheet (SDS) by the submitted sampleinformation.
Summary : As specified by the client, This safety data sheet was prepared in accordance withRegulation(EC) No.1907/2006 (REACH), 1272/2008, as amended by Regulation(EU) No.2015/830 and UN GHS (the 7th revised edition). Please refer to the attached report fordetails.
Shanghai Changyin Testing Technology Co.,Ltd
Approved by:
APPENDIX - MSDS
JOHNSON CONTROLS 119
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 2 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
Safety Data Sheet(SDS)
Conforms toRegulation(EC)No.1907/2006(REACH),1272/2008(CLP),asamendedbyRegulation(EU)No.2015/830
Section 1 - Chemical Product and Company Identification
1.1 Product Identification:
Product Name: Lithium bromide solutionProduct Model: /REACH registrationnumber:
01-2119970708-24-XXXX
1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified uses: Preparation of low temperature refrigerant water, used as a cold source of air conditioningsystems and process , can be widely used in handmade textile, chemical, electronics, food andother industrial and mining enterprises, can also be applied to hotels, theaters, hospitals,buildings and other occasions.
Use advised against: No data available.
1.3 Details of the Manufacture or supplier
Manufacture: Hebei Molor Environmental Protection Technology Co.,Ltd.Address: No.5, Ganjiang Road, Shijiazhuang Economic and Technological Development Zone, HebeiTelephone: +86-311-88081038Fax: +86-311-88382758Email: [email protected]
1.4 Emergency telephone number
Emergency Telephone: +86-311-88081038
Section 2 - Hazards Identification
2.1 Classification of the substance or mixture
Classification according to Regulation (EC) No 1272/2008 [EU-GHS/CLP]
Classification: Skin irritation (Category 2), H315
Skin sensitisation, category 1, H317
JOHNSON CONTROLS120
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 3 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
Serious eye irritation (Category 2A), H319
2.2 Label elements, including precautionary statements
Labels:Pictogram(s):
Signal Word: Warning
Hazard Statement: H315: Causes skin irritation.
H317: May cause an allergic skin reaction.
H319: Causes serious eye irritation.
Precautionary statement(s)
Prevention precautionary
statements:
P261: Avoid breathing dust/fume/gas/mist/vapours/spray.
P264: Wash thoroughly after handling.
P272: Contaminated work clothing should not be allowed out of the workplace
P280: Wear protective gloves/ eye protection/ face protection.
Response Precautionary Statements: P302+352: IF ON SKIN: Wash with soap and water.
P333+313: If skin irritation or a rash occurs: Get medical advice/attention.
P363: Wash contaminated clothing before reuse
P305+P351+P338: If in eyes: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do, continue rinsing.
P337+313: If eye irritation persists get medical advice/attention.
Storage Precautionary Statements: None.
Disposal Precautionary Statements: P501: Dispose of contents and container in accordance with local/regional/national
/international regulations.
2.3 Description of any hazards not otherwise classified
None. See section 11 for more detailed information on health effects and symptoms.
Section 3 - Composition/Information on IngredientSubstance () Preparation (√) Article ()
Composition:
Chemical name CAS No. EC No. REACH No. Content (%)Classification according to
Regulation (EC) No1272/2008 [EU-GHS/CLP]
JOHNSON CONTROLS 121
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 4 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
Lithium bromide 7550-35-8 231-439-8 01-211997070
8-24-XXXX
55% Skin Irrit. 2, H315;
Skin Sens. 1, H317;
Eye Irrit. 2, H319.
Water 7732-18-5 231-791-2 - 45% Not classified.
Abbreviation: CAS No. is Chemical Abstract Service Registry Number.
Section 4 - First Aid Measures4.1 Description of first aid measures:
Eye Contact: IF IN EYES: Rinse cautiously with water for at least 15 minutes. Get medical attention if eye irritationdevelops or persists.
Skin Contact: IF ON SKIN: Remove contaminated clothing and shoes and wipe off the contaminated area, Wash affectedskin with soap and water. If irritation develops and persists, Get medical attention.
Inhalation: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Ifsymptoms occur, obtain medical attention.
Ingestion: IF SWALLOWED, Rinse mouth with water if conscious. Never give anything by mouth to an unconsciousperson.Get medical attention immediately.
4.2 Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in section 2 and section11.
4.3 Indication of any immediate medical attention and special treatment needed
Treat symptomatically and supportively.
Section 5 -Extinguishing media
5.1 Extinguishing media
Suitable extinguishing media:Water spray, Dry chemical, carbon dioxide or alcohol-resistant foam.
Unsuitable extinguishing media: Do not use a solid water stream as it may scatter or spread fire.
5.2 Special hazards arising from the substance or mixture
Overheating or high temperature may release harmful vapors and decomposition products.
5.3 Advice for firefighters
Evacuate unnecessary persons to safe area. As in any fire, Wear self-contained breathing apparatus and full protective gear forfirefighting.
JOHNSON CONTROLS122
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 5 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
5.4 Further information
Avoid contaminated firefighting water flowing into sewers and water source.
Section 6 - Accidental Release MeasuresFor guidance on selection of personal protective equipment see Chapter 8 of this Material Safety Data Sheet. See Chapter 13for information on disposal. Observe the relevant local and international regulations.
6.1 Personal precautions, protective equipment and emergency procedures:
Evacuate area. Ventilate area. Avoid direct contact with spillage. Avoid inhaling vapor. Use suitable personal protectiveequipment.
6.2 Environmental precautions:
Prevent further leakage or spillage if safe to do so. Do not let product enter drains and environment.
6.3 Methods and materials for containment and cleaning up:
Small quantities may be contained by inert material(sand, diatomite, acid binders, universal binders, sawdust). For large spills,dike spilled material or otherwise contain material to ensure runoff does not reach a waterway. Gather the spilled product andkeep in suitable, closed containers for recycle or disposal(see section 13).
Section 7 - Handling and Storage7.1 Precautions for safe handling:
The usual precautionary measures for handling chemicals should be followed.Use in well-ventilated area. Use appropriate, approved safety equipment as in section 8.Avoid contact with skin and eyes. Avoid breathing vapor or mist.Wash thoroughly after handling.Keep container tightly closed when not in use.Do not eat, drink or smoke at the workplace.Keep away from oxidizing agents. Equip with accidental release equipment.
7.2 Conditions for safe storage, including any incompatibilities:
Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Store away from foodstuffs. Do not storetogether with oxidizing agents. Equipped with emergency equipment for accidental leakage.
Section 8 - Exposure Controls, Personal Protection
JOHNSON CONTROLS 123
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 6 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
8.1 Exposure Limits: Not established.
8.2 Exposure controls
Engineering Control: General industrial hygiene practice. Provide appropriate exhaust ventilation. Provide safeshower and eye wash fountain.
Personal protective equipment:
Respiratory Protection: Where risk assessment shows air-purifying respirators are appropriate use a full-face respiratorwith multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as abackup to engineering controls. Use respirators and components tested and approved underappropriate government standards such as NIOSH (US) or CEN (EU).
Eyes Protection: Use face shield and safety glasses if in-eye risk exists. Use equipment for eye protection testedand approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Body Protection: Normal general work suit is enough. If liquid splash exists, wear chemical resistant completesuit,The type of protective equipment must be selected according to the concentration andamount of the dangerous substance at the specific workplace.
Hands Protection: Handle with chemical-resistant gloves. Use proper glove removal technique(without touchingglove's outer surface) to avoid skin contact with this product.
Other Protections: Handle in accordance with good industrial hygiene and safety practice. Wash hands beforebreaks and at the end of workday.
Section 9 - Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance Transparent liquid
Color Colorless
Odor Odorless
pH (55% LiBr: Distilled Water=1g:0g) pH7.88(55% LiBr: Distilled Water=10g:100g)pH13.
Melting point/freezing point Not available.
Initial boiling point and boiling range Not available.
Flash point Not applicable.
Evaporation rate Not available.
Flammability Incombustible.
Upper explosive limit %(V/V) Not applicable.
JOHNSON CONTROLS124
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 7 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
Lower explosive limit %(V/V) Not applicable.
Vapor pressure Not available.
Vapor density Not available.
Relative density Not available.
Solubility(ies) Soluble in water.
Partition coefficient: n-octanol/water Not available.
Ignition temperature Not applicable.
Decomposition temperature Not available.
Viscosity Not available.
Section 10 - Stability and Reactivity10.1 Stability: Stable under normal storage temperature and pressure.
10.2 Conditions to Avoid: Heat, flames and mars.
10.3 Incompatible materials: Strong oxidizing agents, strong acid.
10.4 Hazardous Decomposition Products: Other decomposition products- no data available. In the event of fire:see section 5.
10.5 Possibility of hazardous reactions: None hazardous reactions known under normal condition.
Section 11 - Toxicological Information
Acute Toxicity: Lithium bromide (CAS # 7550-35-8):
LD50 - Rat - Oral - 1800 mg / kg.
Skin Corrosion/Irritation: Causes skin irritation.
Serious Eye Damage/Eye Irritation: Causes serious eye irritation.
Respiratory or Skin Sensitization May cause an allergic skin reaction.
Germ Cell Mutagenicity Based on available data, the classification criteria are not met.
Carcinogenicity: None of the components of this product is listed as a carcinogen by IARC,NTP, US OSHA.
Reproductive Toxicity: Based on available data, the classification criteria are not met.
Specific Target Organ Toxicity - SingleExposure (Globally Harmonized System):
Based on available data, the classification criteria are not met.
Specific Target Organ Toxicity - RepeatedExposure (Globally Harmonized System):
Based on available data, the classification criteria are not met.
Aspiration Hazard: Based on available data, the classification criteria are not met.
JOHNSON CONTROLS 125
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 8 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
Potential Health Effects:
Inhalation: Long-term inhalation can cause skin rashes and central nervous disorders.
Skin Contact: Causes skin irritation. May cause an allergic skin reaction.
Eye Contact: Causes serious eye irritation.
Ingestion: May be harmful if ingested. Large doses of lithium bromide can inhibit thecentral nervous system.
Section 12 - Ecological Information12.1 ToxicityLithium bromide (CAS # 7550-35-8):Toxicity to fish LC50 - Rainbow trout - 438 mg / l - 96 h; NOEC - Rainbow trout - 128 mg / l - 96 h.
12.2 Persistence and degradabilityMethods of biodegradation test do not apply to inorganic substances.
12.3 Bioaccumulative potentialNo data available.
12.4 Mobility in soilNo data available
12.5 Results of PBT and vPvB assessmentThis substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or verypersistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
12.6 Other adverse effectsDo not allow materials to release to drains or water body.
Section 13 - Disposal Considerations
Waste treatment methods
Product
Waste should be poured into special bucket (with lid) for further disposal.Dispose of product and contaminated packaging ashazardous waste and send to to a licensed disposal company. Observe according to the national and local related regulations.
Contaminated packaging
Containers may still present chemical hazard when empty. Return to supplier for recycling if possible.
Section 14 - Transport Information
JOHNSON CONTROLS126
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 9 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
14.1 UN Number:
ADR/RID, IMDG, IATA Not regulated as dangerous goods.
14.2 UN proper shipping name:
ADR/RID, IMDG, IATA Not dangerous goods
14.3 Transport hazard class(es):
ADR/RID, IMDG, IATA Not regulated as dangerous goods.
14.4 Packing group:
ADR/RID, IMDG, IATA Not regulated as dangerous goods.
14.5 Environmental hazards: No.
14.6 Special precautions for user:
Choose suitable means of transport and the appropriate transport and storageconditions Equipped with firefighting equipment and emergency leakage equipment.If transport by road, please follow the prescribed route. Incompatible materials: strongacid, strong oxidant.
Section 15 - Regulatory Information
EU Regulations
Classification according to Regulation (EC) No 1272/2008 [EU-GHS/CLP]Skin irritation (Category 2), H315Skin sensitisation, category 1, H317Serious eye irritation (Category 2A), H319
US Regulations
OSHA:OSHAHazard Communication Standard Status: This product is considered to be a hazardous substance under OSHA’sFederal Hazard Communication Standard 29 CFR 1910.1200.
USA SARA
SARA 302 ComponentsSARA 302: No chemicals in this material are subject to the reporting requirements of SARATitle III, Section 302.SARA 313 Components (Specific toxic chemical listings)SARA 313: This material does not contain any chemical components with known CAS numbers that exceed the threshold (DeMinimis) reporting levels established by SARA Title III, Section 313Canadian RegulationsSARA 311/312 HazardsAcute Health Hazard, Chronic Health Hazard
JOHNSON CONTROLS 127
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 10 / 10MSDS NO.: A001R1803020201Creation Date: March 4, 2018
California Prop. 65 ComponentsThis product does not contain any chemicals known to State of California to cause cancer, birth defects, or any otherreproductive harm.
Section 16 - Additional InformationAbbreviations:
pH- Relates to hydrogen ion concentration - this value will relate to a scale of 0 - 14, where 0 is highly acidic and 14 ishighly alkaline
OSHA- Occupational Safety and Health AdministrationNTP- National Toxicilogy ProgramIARC- International Agency for Research on CancerCAS#- Chemical Abstract Service number - used to uniquely identify chemical compoundsACGIH- The American Conference of Governmental Industrial HygienistsADR- Agreement on Dangerous Goods by RoadIATA - International Air Transport AssociationIMDG- International Maritime Dangerous Goods
Further Information:
-The contents and format of this SDS are in accordance with Regulation (EC) No 190712006, 1272/2008 and Regulation (EU)No 2015/830.
-The above information is based on the data of which we are aware and is believed to be correct as of the data hereof. Sincethis information may be applied under conditions beyond our control and with which may be unfamiliar and since data madeavailable subsequent to the data hereof may suggest modifications of the information, we do not assume any responsibility forthe results of its use. This information is furnished upon condition that the person receiving it shall make his own determinationof the suitability of the material for his particular purpose.
Department Issuing SDS: Hebei Molor Environmental Protection Technology Co.,Ltd.
Issue Date:March 4, 2018
JOHNSON CONTROLS128
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 1 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
Applicant: Hebei Molor Environmental Protection Technology Co.,Ltd.Address: No.5, Ganjiang Road, Shijiazhuang Economic and Technological Development Zone, Hebei
Sample information:Sample name: Dilithium molybdate solutionModel: 20%Applicant sheet received date: March 2, 2018Edit period: From March 2, 2018 to March 4, 2018
Required service : As specified by the client, to edit Safety Data Sheet (SDS) by the submitted sampleinformation.
Summary : As specified by the client, This safety data sheet was prepared in accordance withRegulation(EC) No.1907/2006 (REACH), 1272/2008, as amended by Regulation(EU) No.2015/830 and UN GHS (the 7th revised edition). Please refer to the attached report fordetails.
Shanghai Changyin Testing Technology Co.,Ltd
Approved by:
JOHNSON CONTROLS 129
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 2 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
Safety Data Sheet(SDS)
Conforms toRegulation(EC)No.1907/2006(REACH),1272/2008(CLP),asamendedbyRegulation(EU)No.2015/830
Section 1 - Chemical Product and Company Identification
1.1 Product Identification:
Product Name: Dilithium molybdate solutionProduct Model: 20%REACH registrationnumber:
-
1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified uses: Dilithium molybdate solutionUse advised against: No data available.
1.3 Details of the Manufacture or supplier
Manufacture: Hebei Molor Environmental Protection Technology Co.,Ltd.Address: No.5, Ganjiang Road, Shijiazhuang Economic and Technological Development Zone, HebeiTelephone: +86-311-88081038Fax: +86-311-88382758Email: [email protected]
1.4 Emergency telephone number
Emergency Telephone: +86-311-88081038
Section 2 - Hazards Identification
2.1 Classification of the substance or mixture
Classification according to Regulation (EC) No 1272/2008 [EU-GHS/CLP]
Classification: Skin irritation (Category 2), H315Serious eye irritation (Category 2A), H319Specific target organ toxicity - single exposure (Category 3), Respiratory system,H335
2.2 Label elements, including precautionary statements
JOHNSON CONTROLS130
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 3 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
Labels:Pictogram(s):
Signal Word: WarningHazard Statement: H315 Causes skin irritation.
H319 Causes serious eye irritation..H335 May cause respiratory irritation.
Precautionary statement(s)
Prevention precautionarystatements:
P261 Avoid breathing dust/fume/gas/mist/vapors/spray.P264 Wash thoroughly after handling.P271 Use only outdoors or in a well-ventilated area.P280 Wear protective gloves/ eye protection/ face protection.
Response PrecautionaryStatements:
P303+P361+P353 If on skin(or hair):Remove/take off immediately all contaminatedclothing. Rinse skin with water/shower.P332+313 If skin irritation persists get medical advice/attention.P304+P340 If inhaled, Remove victim to fresh air and keep at rest in a positioncomfortable for breathing.P304+312 Call a POISON CENTER or doctor/physician if you feel unwell.P305+P351+P338 If in eyes: Rinse cautiously with water for several minutes.Remove contact lenses, if present and easy to do, continue rinsing.P337+313 If eye irritation persists get medical advice/attention.
Storage Precautionary Statements: P405: Store locked upP403+233: Store in a well ventilated place. Keep container tightly closed
Disposal PrecautionaryStatements:
P501: Dispose of contents and container in accordance with local/regional/national/international regulations.
2.3 Description of any hazards not otherwise classified
None. See section 11 for more detailed information on health effects and symptoms.
Section 3 - Composition/Information on IngredientSubstance () Preparation (√) Article ()
Composition:
Chemicalname
CAS No. EC No. REACH No. Content (%)Classification according to
Regulation (EC) No1272/2008 [EU-GHS/CLP]
Dilithium 13568-40-6 236-977-7 - 20% Skin Irrit. 2, H315;
JOHNSON CONTROLS 131
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 4 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
molybdate Eye Irrit. 2, H319;
STOT SE 3, H335.
Water 7732-18-5 231-791-2 - 80% Not classified.
Abbreviation: CAS No. is Chemical Abstract Service Registry Number.
Section 4 - First Aid Measures
4.1 Description of first aid measures:
Eye Contact: IF IN EYES: Rinse cautiously with water for at least 15 minutes. Get medical attention if eye irritationdevelops or persists.
Skin Contact: IF ON SKIN: Remove contaminated clothing and shoes and wipe off the contaminated area, Wash affectedskin with soap and water. If irritation develops and persists, Get medical attention. Wash contaminatedclothing before reuse.
Inhalation: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Ifsymptoms occur, obtain medical attention.
Ingestion: IF SWALLOWED, Rinse mouth with water if conscious. Never give anything by mouth to an unconsciousperson.Get medical attention immediately.
4.2 Most important symptoms and effects, both acute and delayed
The most important known symptoms and effects are described in section 2 and section11.
4.3 Indication of any immediate medical attention and special treatment needed
Treat symptomatically and supportively.
Section 5 -Extinguishing media
5.1 Extinguishing media
Suitable extinguishing media:Water spray, Dry chemical, carbon dioxide or alcohol-resistant foam.
Unsuitable extinguishing media: Do not use a solid water stream as it may scatter or spread fire.
5.2 Special hazards arising from the substance or mixture
Overheating or high temperature may release harmful vapors and decomposition products.
5.3 Advice for firefighters
Evacuate unnecessary persons to safe area. As in any fire, Wear self-contained breathing apparatus and full protective gear forfirefighting.
JOHNSON CONTROLS132
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 5 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
5.4 Further information
Avoid contaminated firefighting water flowing into sewers and water source.
Section 6 - Accidental Release MeasuresFor guidance on selection of personal protective equipment see Chapter 8 of this Material Safety Data Sheet. See Chapter 13for information on disposal. Observe the relevant local and international regulations.
6.1 Personal precautions, protective equipment and emergency procedures:
Evacuate area. Ventilate area. Avoid direct contact with spillage. Avoid inhaling vapor. Use suitable personal protectiveequipment.
6.2 Environmental precautions:
Prevent further leakage or spillage if safe to do so. Do not let product enter drains and environment.
6.3 Methods and materials for containment and cleaning up:
Small quantities may be contained by inert material(sand, diatomite, acid binders, universal binders, sawdust). For large spills,dike spilled material or otherwise contain material to ensure runoff does not reach a waterway. Gather the spilled product andkeep in suitable, closed containers for recycle or disposal(see section 13).
Section 7 - Handling and Storage7.1 Precautions for safe handling:
The usual precautionary measures for handling chemicals should be followed.Use in well-ventilated area. Use appropriate, approved safety equipment as in section 8.Avoid contact with skin and eyes. Avoid breathing vapor or mist.Wash thoroughly after handling.Keep container tightly closed when not in use.Do not eat, drink or smoke at the workplace.Keep away from oxidizing agents. Equip with accidental release equipment.
7.2 Conditions for safe storage, including any incompatibilities:
Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Store away from foodstuffs. Do not storetogether with strong acids, strong bases. Equipped with emergency equipment for accidental leakage.
Section 8 - Exposure Controls, Personal Protection
JOHNSON CONTROLS 133
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 6 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
8.1 Exposure Limits:
Substance CAS No.USA. Occupational Exposure Limits(OSHA) - Table Z-1 Limits for Air
Contaminants
USA. ACGIH ThresholdLimit Values(TLV)
Dilithium molybdate 13568-40-6 TWA:5 mg/m3 TWA:0.5 mg/m3
8.2 Exposure controls
Engineering Control: General industrial hygiene practice. Provide appropriate exhaust ventilation. Provide safeshower and eye wash fountain.
Personal protective equipment:
Respiratory Protection: Where risk assessment shows air-purifying respirators are appropriate use a full-face respiratorwith multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as abackup to engineering controls. Use respirators and components tested and approved underappropriate government standards such as NIOSH (US) or CEN (EU).
Eyes Protection: Use face shield and safety glasses if in-eye risk exists. Use equipment for eye protection testedand approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Body Protection: Normal general work suit is enough. If liquid splash exists, wear chemical resistant completesuit,The type of protective equipment must be selected according to the concentration andamount of the dangerous substance at the specific workplace.
Hands Protection: Handle with chemical-resistant gloves. Use proper glove removal technique(without touchingglove's outer surface) to avoid skin contact with this product.
Other Protections: Handle in accordance with good industrial hygiene and safety practice. Wash hands beforebreaks and at the end of workday.
Section 9 - Physical and Chemical Properties
Information on basic physical and chemical properties
Appearance Transparent liquid
Color Colorless
Odor Odorless
pH Not available.
Melting point/freezing point Not available.
Initial boiling point and boiling range Not available.
Flash point Not applicable.
JOHNSON CONTROLS134
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 7 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
Evaporation rate Not available.
Flammability Incombustible.
Upper explosive limit %(V/V) Not applicable.
Lower explosive limit %(V/V) Not applicable.
Vapor pressure Not available.
Vapor density Not available.
Relative density Not available.
Solubility(ies) Soluble in water.
Partition coefficient: n-octanol/water Not available.
Ignition temperature Not applicable.
Decomposition temperature Not available.
Viscosity Not available.
Section 10 - Stability and Reactivity10.1 Stability: Stable under normal storage temperature and pressure.
10.2 Conditions to Avoid: Heat, flames and mars.
10.3 Incompatible materials: Strong acids, Strong bases.
10.4 Hazardous Decomposition Products: Other decomposition products- no data available. In the event of fire:see section 5.
10.5 Possibility of hazardous reactions: None hazardous reactions known under normal condition.
Section 11 - Toxicological InformationAcute Toxicity: No data available.
Skin Corrosion/Irritation: Causes skin irritation.
Serious Eye Damage/Eye Irritation: Causes serious eye irritation.
Respiratory or Skin Sensitization Based on available data, the classification criteria are not met.
Germ Cell Mutagenicity Based on available data, the classification criteria are not met.
Carcinogenicity: None of the components of this product is listed as a carcinogen by IARC,
NTP, US OSHA.
Reproductive Toxicity: Based on available data, the classification criteria are not met.
Specific Target Organ Toxicity - Single
Exposure (Globally Harmonized System):
May cause respiratory irritation.
Specific Target Organ Toxicity - Repeated Based on available data, the classification criteria are not met.
JOHNSON CONTROLS 135
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 8 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
Exposure (Globally Harmonized System):
Aspiration Hazard: Based on available data, the classification criteria are not met.
Potential Health Effects:
Inhalation: May cause respiratory irritation.
Skin Contact: Causes skin irritation.
Eye Contact: Causes serious eye irritation.
Ingestion: May be harmful if ingested. Large doses of lithium ion have caused
dizziness and prostration, and can cause kidney damage if sodium intake is
limited. Dehydration, weight loss, dermatological effects, and thyroid
disturbances have been reported. Central nervous system effects that
include slurred speech, blurred vision, sensory loss, ataxia, and convulsions
may occur. Diarrhea, vomiting, and neuromuscular effects such as tremor,
clonus, and hyperactive reflexes may occur as a result of repeated exposure
to lithium ion., Dermatitis, To the best of our knowledge, the chemical,
physical, and toxicological properties have not been thoroughly
investigated.
Section 12 - Ecological Information12.1 ToxicityNo data available.
12.2 Persistence and degradabilityMethods of biodegradation test do not apply to inorganic substances.
12.3 Bioaccumulative potentialNo data available.
12.4 Mobility in soilNo data available
12.5 Results of PBT and vPvB assessmentThis substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or verypersistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.
12.6 Other adverse effectsDo not allow materials to release to drains or water body.
Section 13 - Disposal Considerations
JOHNSON CONTROLS136
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 9 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
Waste treatment methods
Product
Waste should be poured into special bucket (with lid) for further disposal.Dispose of product and contaminated packaging ashazardous waste and send to to a licensed disposal company. Observe according to the national and local related regulations.
Contaminated packaging
Containers may still present chemical hazard when empty. Return to supplier for recycling if possible.
Section 14 - Transport Information
14.1 UN Number:
ADR/RID, IMDG, IATA Not regulated as dangerous goods.
14.2 UN proper shipping name:
ADR/RID, IMDG, IATA Not dangerous goods
14.3 Transport hazard class(es):
ADR/RID, IMDG, IATA Not regulated as dangerous goods.
14.4 Packing group:
ADR/RID, IMDG, IATA Not regulated as dangerous goods.
14.5 Environmental hazards: No.
14.6 Special precautions for user:
Choose suitable means of transport and the appropriate transport and storageconditions Equipped with firefighting equipment and emergency leakageequipment. If transport by road, please follow the prescribed route. Incompatiblematerials: strong acid, strong base.
Section 15 - Regulatory Information
EU Regulations
Classification according to Regulation (EC) No 1272/2008 [EU-GHS/CLP]Skin irritation (Category 2), H315Serious eye irritation (Category 2A), H319Specific target organ toxicity - single exposure (Category 3), Respiratory system, H335
US Regulations
JOHNSON CONTROLS 137
APPENDIX - MSDSFORM 155.36-ICOM2.EN.CE/GB ISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 10 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
OSHA:OSHAHazard Communication Standard Status: This product is considered to be a hazardous substance under OSHA’sFederal Hazard Communication Standard 29 CFR 1910.1200.
USA SARA
SARA 302 ComponentsSARA 302: No chemicals in this material are subject to the reporting requirements of SARATitle III, Section 302.SARA 313 Components (Specific toxic chemical listings)SARA 313: This material does not contain any chemical components with known CAS numbers that exceed the threshold (DeMinimis) reporting levels established by SARA Title III, Section 313Canadian RegulationsSARA 311/312 HazardsAcute Health HazardCalifornia Prop. 65 ComponentsThis product does not contain any chemicals known to State of California to cause cancer, birth defects, or any otherreproductive harm.
Section 16 - Additional InformationAbbreviations:
pH- Relates to hydrogen ion concentration - this value will relate to a scale of 0 - 14, where 0 is highly acidic and 14 ishighly alkaline
OSHA- Occupational Safety and Health AdministrationNTP- National Toxicilogy ProgramIARC- International Agency for Research on CancerCAS#- Chemical Abstract Service number - used to uniquely identify chemical compoundsACGIH- The American Conference of Governmental Industrial HygienistsADR- Agreement on Dangerous Goods by RoadIATA - International Air Transport AssociationIMDG- International Maritime Dangerous Goods
Further Information:
-The contents and format of this SDS are in accordance with Regulation (EC) No 190712006, 1272/2008 and Regulation (EU)No 2015/830.
-The above information is based on the data of which we are aware and is believed to be correct as of the data hereof. Sincethis information may be applied under conditions beyond our control and with which may be unfamiliar and since data madeavailable subsequent to the data hereof may suggest modifications of the information, we do not assume any responsibility forthe results of its use. This information is furnished upon condition that the person receiving it shall make his own determinationof the suitability of the material for his particular purpose.
Department Issuing SDS: Hebei Molor Environmental Protection Technology Co.,Ltd.
Issue Date:March 4, 2018
JOHNSON CONTROLS138
APPENDIX - MSDS FORM 155.36-ICOM2.EN.CE/GBISSUE DATE: 04/05/2019
Shanghai Changyin Testing Technology Co.,LtdRoom 1018, V6 Times Business Building, No.16, Xinyuan Road, Anting Town, Jiading District, Shanghai
Tel:+86-021-61842208, Fax:+86-021-61842208 E-mail:[email protected], http://www.changyin-lab.com
Page 11 / 11SDS NO.: A001R1803020302Creation Date: March 4, 2018
5000 Renaissance Drive, New Freedom, Pennsylvania USA 17349 1-800-524-1330 Subject to change without notice. Printed in USACopyright © by Johnson Controls 2019 www.johnsoncontrols.com ALL RIGHTS RESERVED Form 155.36-ICOM2.EN.CE.GB (419)Issue Date: April 05, 2019 Supersedes Form 155.36-ICOM2.EN.GB (1118)