dr engp 1.1 r.3piping engineering
TRANSCRIPT
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
1/658
GUIDELINES OF E&P PRODUCTION ENGINEERING Nº:
DR-ENGP-1.1 – R.3
CLIENT: E&P PAGE: 1 of 24
OWNER: E&P Production Engineering Executive Management
AREA: Offshore Production Installation
TITLE: Piping Standard and Material for Oil Production and Process Facilities
VOLUME: I – Corporate Engineering Requirements
PART:
CHAPTER:
APPROVAL ENGP Gerência Executiva de Engenharia de Produção
VERIFICATION IPP Gerência Geral de Instalações e Processos de Produção
EXECUTION EISA Gerência de Engenharia de Instalações de Superfície e Automação
Approved29/11/2010
CORPORATE INFORMATION
DR-ENGP-1.1-R.3
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTIONAND PROCESS FACILITIES
Note: For requisition of materials referred here in through their TAG’s, thePetrobras / E&P materials standardization PM-1/2, shall be used.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
2/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 2 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
INDEX
1 – Line numering systems.2 – Reference standards.3 – Abreviations.4 – Service symbols, pressure rating and piping.5 – Piping material standardization.6 – Appendixs.
Appendix Index
1 – Connection details for temperature wells.2 – Connection details for drains and vents.3 – Connection details for pressure instruments.4 – Connection details for orifice flange.5 – Corrosive effect of liquid gaseous hydrocarbons and produced water.
10 – Procedure for coating bolts and nuts.11 – Specifications for Utilization Sacrificial Anodes in Piping, Spec A5sheet
2/212 – Branch connections tables.13 – Procedure for internal coating of piping with polyethylene.
14 – Fully tight valves.15 – Isolating joint.16 – Welding qualification for superduplex.17 – Minimum requirements for superduplex cast steel valvemanufacturing.18 – Technical data of organic coated for piping and valves.19 – Minimum requirements for non-metallic piping20 – Industrial Valve Supply Requirements for E&P21 – Welding Qualification for Inconel 625 “Weld overlay” Clad pipe.
7 – Valves descriptions.
8 – Piping material descriptions.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
3/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 3 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
1 – Line Numbering System
(1) – (2) – (3) – (4) – (5)
(1) – Nominal diameter (inches)(2) – Service symbols (see symbology)(3) – Piping material standardization(4) – Sequencial numbering of line(5) – Indication insulation:
PP – Personal protectionHC – Heat conservationCC – Cold conservation
Exemplo:
6” _____ P ___ B10 ___ 010 ___HCHot insulated line
Sequencial number
Piping material standardization
Process (non-corrosive hydrocarbon)
Nominal diameter:
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
4/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 4 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
2 – Reference Standards
STANDARD TITLE
API RP 14E Recommended Practice for Design andInstallation of offshore Production Platform PipingSystems.
API SPEC 5L Specification for Line Pipe.
API SPEC 6D ISO 14313 – Petroleum and Natural GasIndustries – Pipeline Tranportation Systems-Pipeline Valves.
API STD 594 Check Valves: Wafer, Wafer-Lug, and DoubleFlanged Type.
API STD 600 ISO 10434 – Bolted Bonnet Steel Gate Valves forPetroleum and Natural Gas Industries.
API STD 602 ISO 15671 – Compact Steel Gate Valves –
Flanged, Threaded, Welding, and.Extended –Body Ends.
API STD 609 Butterfly Valves: Double Flanged, Lug and Wafer – Type.
ASME B1.1 Unified Inch Screw Threads (UN and UNR ThreadForm).
ASME B1.20.1 Pipe Threads, General Purpose (Inch).
ASME B16.1 Cast Iron Pipe Flanges and Flanged FittingsClasses 25, 125 and 250.
ASME B16.5 Pipe flanges and flanged fittings NPS 1/2 throughNPS 24 metric/inch standard revision e ASMEB16.5
ASME B16.9 Factory - made wrought steel buttwelding fittings.
ASME B16.11 Forged Fittings, Socket-Welding and Threaded.
ASME B16.20 Metallic gaskets for pipe flanges ring-joint, spiral-wound, and jacketed addenda A-07/21/2000.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
5/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 5 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
STANDARD TITLE
ASME 16.21 Nonmetallic Flat Gaskets for Pipe Flanges.
ASME B16.25 Buttwelding End.
ASME B16.28 Wrought Steel Buttwelding Short Radius Elbowsand Returns.
ASME B16.47 Large diameter Steel Flanges (NPS 26 throughNPS 60).
ASME B18.2.2 Square and Hex Nuts (Inch Series).
ASME B31.3 Process Piping.
ASME B36.10 Welded and Seamless Wrought Steel Pipe.
ASME B36.19 Stainless Steel Pipe
ASTM A105 Standard Specification for Carbon Steel Forgingsfor Piping Applications.
ASTM A106 Standard Specification for Seamless Carbon SteelPipe for High-Temperature Service.
ASTM A123 Standard Specification for Zinc (Hot-DipGalvanized) Coatings on Iron and Steel Products.
ASTM A126 Standard Specification for Gray Iron Castings forValves, Flanges, and Pipe Fittings.
ASTM A182 Standard Specification for Forged or Rolled Alloy-.Steel Pipe Flanges, Forged Fittings, and Valves
and Parts for High-Temperature Service.
ASTM A193 Standard Specification for Alloy-Steel andStainless Steel Bolting Materials for High-Temperature Service.
ASTM A194 Standard specification for carbon and alloy steelnuts for bolts for high pressure or hightemperature service, or both.
ASTM A216 Standard Specification for Steel Castings, Carbon,Suitable for Fusion Welding, High-TemperatureService.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
6/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 6 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
STANDARD TITLE
ASTM A234 Standard Specification for Piping Fittings ofWrought Carbon Steel and Alloy Steel forModerate and High Temperature Service.
ASTM A312 Standard Specification for Seamless, Welded,and Heavily Cold Worked Austenitic StainlessSteel Pipes.
ASTM A320 Standard Specification for Alloy-Steel andStainless Steel Bolting Materials Low High-
Temperature Service.
ASTM A333 Standard Specification for Seamless and WeldedSteel Pipe for Low-Temperature Service.
ASTM A350 Standard Specification for Carbon and Low-AlloySteel Forgings, Requiring Notch ToughnessTesting for Piping Components.
ASTM A351 Standard Specification for Castings, Austenitic,Austenitic-Ferritic (Duplex), for Pressure-
Containing Parts.
ASTM A352 Standard Specification for Steel Castings, Ferriticand Martensitic, for Pressure-Containing Parts,Suitable for Low-Temperature Service.
ASTM A358 Standard Specification for Electric-Fusion-WeldedAustenitic Chromium-Nickel Stainless Steel Pipefor High-Temperature Service and GeneralApplications
ASTM A403 Standard Specification for Wrought AusteniticStainless Steel Piping Fittings.
ASTM A420 Standard Specification for Piping Fittings ofWrought Carbon Steel and Alloy Steel for Low-Temperature Service.
ASTM A487 Standard Specification for Steel Castings Suitablefor Pressure Service.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
7/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 7 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
STANDARD TITLE
ASTM A522 Standard Specification for Forged or Rolled 8 and9% Nickel Alloy Steel Flanges, Fittings, Valves,and Parts for Low-Temperature Service
ASTM A536 Standard Specification for Ductile Iron Castings.
ASTM A564 Standard Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars andShapes.
ASTM A671 Standard Specification for Eletric-Fusion-WeldedSteel Pipe for Atmospheric and LowerTemperatures.
ASTM A694 Standard Specification for Carbon and Alloy SteelForgings for Pipe Flanges, Fittings, Valves, andParts for High-Pressure Transmission Service.
ASTM A790 Standard Specification for Seamless and WeldedFerritic/Austenitic Stainless Steel Pipe.
ASTM A815 Standard Specification for Wrought Ferritic,Ferritic/Austenitic, and Martensitic Stainless SteelPiping Fittings.
ASTM A928 Standard Specification for Ferritic/Austenitic(Duplex) Stainless Steel Pipe Electric FusionWelded with Addition of Filler Metal
ASTM A995 Standard Specification for Castings, Austenitic-Ferritic (Duplex) Stainless Steel, for Pressure-Containing Parts
ASTM B62 Standard Specification for Composition Bronze orOunce Metal Castings.
ASTM B584 Standard Specification for Copper Alloy SandCastings for General Applications.
ASTM D1784 Standard Specification for Rigid Poly (VinylChloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds.
ASTM D1785 Standard Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe, Schedules 40, 80 and 120.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
8/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 8 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
STANDARD TITLE
ASTM D2467 Standard Specification for Poly (Vinyl Chloride)(PVC) Plastic Pipe Fittings, Schedule 80.
ASTM D3567 Standard Practice for Determining Dimensions ofFiberglass (Glass-Fiber-Reinforced ThermosettingResin) Pipe and Fittings R (2002).
ASTM D4024 Standard Specification for Machine Made"Fiberglass" (Glass-Fiber-ReinforcedThermosetting Resin) Flanges (2000).
ASTM F1173 Standard Specification for Thermosetting ResinFiberglass Pipe Systems to be used for MarineApplications (2001).
ASTM F439 Standard Specification for Chlorinated Poly (VinylChloride) (CPVC) Plastic Pipe Fittings, Schedule80.
BSI BS 1873 Stell Globe and Globe Stop and Check Valves(flanged and butt-welding ends) for the Petroleum,
Petrochemical and Allied Industries.
BSI BS 3799 Steel Pipe Fittings, Screwed and Socket-Weldingfor the Petroleum Industry.
BSI BS 5152 Cast Iron Globe and Globe Stop and CheckValves for General Purposes.
BSI BS 5351 Steel Ball Valves for the Petroleum, Petrochemicaland Allied Industries.
BSI BS 5352 Steel Wedge Gate, Globe and Check Valves 50mm and Smaller for the Petroleum, Petrochemicaland Allied Industries.
EEMUA 144 90/10 Copper Nickel Alloy Piping for OffshoreApplications. Tubes Seamless and Welded.
EEMUA 145 90/10 Copper Nickel Alloy Piping for OffshoreApplications. Flanges Composite and Solid.
EEMUA 146 90/10 Copper Nickel Alloy Piping for OffshoreApplications. Fittings.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
9/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 9 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
STANDARD TITLE
IMO A 753(18) International Maritime Organization - Resolution A753(18).
MSS SP-6 Standard Finishes for Contact Faces de PipeFlanges and Connecting-End Flanges of Valvesand Fittings.
MSS SP-70 Cast Iron Gate Valves, Flanged and ThreadedEnds.
MSS SP-71 Gray Iron Swing Check Valves, Flanged andThreaded Ends
MSS SP-72 Ball Valves with Flanged or Butt-Welding Ends forGeneral Service.
MSS SP-80 Bronze Gate, Globe, Angle and Check Valves.
MSS SP-83 Steel Pipe Unions, Socket-Welding and Threaded.
MSS SP-88 Diaphragm Type Valves.
MSS SP-95 Swage (d) Nipples and Bull Plugs.
NACE MR0175 ISO 15156 - Metals for Sulfide Stress Crackingand Stress Corrosion Cracking Resistance in SourOilfield Environments.
NORSOK L-005 Compact Flanged Connections.
NORSOK M-001 Materials Selection
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
10/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 10 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
3 – Abbreviations
AISI - American Iron and Steel Institute
API - American Petroleum Institute
ASME - American Society of Mechanical Engineering
ASTM - American Society For Testing And Materials
BF - Strap-Flange
BRE - Reduction Bushing
BS - British Standards
BUJ - Plug
CCS - Centrifugal Carbon Steel
CL - Class
CPVC - Chlorinated Poly (Vinyl Chloride)
CR - Chrome
CRC - Short Radius Curve
CRL - Long Radius Curve
CRUZ - Cross
Cu-Ni - Copper/Nikel
DN - Nominal Diameter
EBL - Elbolet (Curved Collar)
EEMUA - Engineering Equipment and Materials Users Association
EPDM - Ethylene Propylene Diene Monomer
FLG - Flange
FF - Flat Face
RF - Raised Face
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
11/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 11 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
FRP - Fiber Reinforced Plastic
FUC - Female Union Capilary
GALV - Galvanized
GR - Grade
HEX - Hexagonal
IMO - International Maritime Association
IN - Inch
J - Joint
JA - Ring Joint
JE - Spiral Wound
JI - Insulated Joint
JO - Elbow
L - Coupling
LRE - Reduction Sleeve
LREFF - Female X Female Reduction Sleeve
LREMF - Male X Female Reduction Sleeve
LTL - Latrolet (Lateral Collar)
MAX - Maximum
ML - Half Coupling
MSS - Manufacturers Standardization Society Of Valve And FittingsIndustry
MUC - Male Union Capilary
NACE - National Association of Corrosion Engineers
NIP - Nipple
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
12/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 12 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
NIPC - Short Nipple
NIPL - Niple Longo
NIPR-C - Concentric Reduction Nipple
NIPR-E - Eccentric Reduction Nipple
NPT - National Pipe (ASME B1.20.1 Thread)
NSFHT - National Standard Fire Hose Thread
PE - Polyethylene
PSI - Pounds Per Square Inch
PTFE - Poli Tetra Fluor Etileno
PVC - Poly (Vinyl Chloride)
RED - Reduction
REDC - Concentric Reduction
REDE - Eccentric Reduction
RTJ - Ring Type Joint
SCH - Schedule
SDV - Shut Down Valve
STD - Standard
SW - Socket Weld
TAM - Plug
TEMP - Temperature
THD - Threaded
TRE - Reduction Tee
UN - Union
UN FLEX - Flexible Union
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
13/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 13 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
UN ISOL - Insulated Union
UNS - Unified Numbering System
VAG - Needle Valve
VB - Butterfly Valve
VE - Ball Valve
VET - Fully Tight Valve
VG - Gate Valve
VG ABRAS - Gate Valve for Abrasive Materials
VGL - Globe Valve
VR - Check Valve
WOL - Weldolet (Beveled Collar)
XS - Extra Strong
XXS - Double Extra Strong
WN - Welding Neck
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
14/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 14 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
15/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 15 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
16/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 16 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
17/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 17 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
18/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 18 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
19/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 19 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
Spec Rev. Class Service/FluidA4 Q 125 SFWA8 R 125 GW HWU SP WWB3 D 150 AM CNI D DW F FG H IA IG IGN IN JF PW PWH PC BG SPB4 F 150 HF HWP S SCB5 G 150 FPB6 G 150 F G GL PB7 C 150 FWB7R D 150 FL FW BR SWB9 H 150 AM DA DFC F PC PCW SPB10 G 150 AM BG CHW CI D DF F FG FL G IW OL P SA SN WB11 B 150 ADW PC PCWB12 F 150 PC
B14 C 150 BW CN IW IWC SWB15 A 150 BW P PC PCW SWW CB16 0 150 AM PCB17 0 150 PCB19 0 150 FB20 A (*) CHW CN GW PW W WWB21 A (*) HWU PWHB22 B (*) BW DA IWC SWB23 C (*) BW SWB24 B (*) FWB25 D (*) DA PCWC3 B 300 CNI D FG H PCC4 A 300 HF HWP S SCC5 B 300 FPC6 F 300 F G GL PC8 D 300 DOC9 G 300 PCC10 F 300 AM BG CI D FG G IW P SA SN WC11 0 300 PCWC12 E 300 PCC14 C 300 IW SWC16 0 300 AM PCC30 0 300 PCE3 D 600 AM CNI D FG H PCE4 A 600 HWP S SC
E5 A 600 FPE6 F 600 G GL PE6R A 600 GLE8 E 600 DOE9 F 600 PC
(*) Maximum Working Pressure (psig), according to the table – Temperature and Pressure Limit, of therespective Spec.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
20/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 20 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
Spec Rev. Class Service/FluidE10 C 600 AM BG CI FG G IW P WE10R A 600 WE11 0 600 PCWE14 B 600 IWE16 0 600 AM DF DFC P PCE17 0 600 PCE30 0 600 PCF3 B 900 CNI D FG H PCF4 A 900 S SCF5 A 900 FPF6 D 900 GL PF6R A 900 GL P
F10 B 900 BG CI G HWU IW P WF10R A 900 BG CI G P WF11 0 900 PCWF14 B 900 IWG3 C 1500 CNI D FG G H P PCG4 A 1500 S SCG5 A 1500 FPG6 D 1500 G GL PG6R A 1500 GL PG10 C 1500 BG CI G IW P WG10P C 1500 PG10R A 1500 BG CI G P WG11 C 1500 PCWG12 C 1500 PCG12P 0 1500 PCG14 B 1500 IWG16 0 1500 PC DFCG16P 0 1500 PCG18 0 1500 PG19 0 1500 PCH3 B 2500 CNI HH5 B 2500 FPH10 C 2500 D PH10P 0 2500 PH11 0 2500 PCW
H14 0 2500 IWH30 0 2500 PCH30P 0 2500 PCJ12 0 10000psi PCJ31 0 10000psi PJ31P 0 10000psi P
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
21/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 21 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
Class 125 150 300 600 900 1500 2500/10000
Family A B C E F G H / JB3(-100ºC/370ºC) C3(-46ºC/149ºC) E3(-100ºC/190ºC) F3 (-100ºC/200ºC) G3(-100ºC/210ºC) H3 (-60ºC/210ºC)
Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel Stainless steel ASTM A312 ASTM A312 ASTM A312 ASTM A312 ASTM A358 ASTM A358
3
Gr TP 316L Gr TP 316L Gr TP 316L Gr TP 316L Gr 316L Cl 1 ou 3 Gr 316L Cl 1 ou
A4 (0ºC/90ºC) B4 (0ºC/350ºC) C4 (0ºC/350ºC) E4 (0ºC/350ºC) F4 (0ºC/350ºC) G4 (0ºC/350ºC)
Carbon steel API Carbon steel Carbon steel Carbon steel API Carbon steel API Carbon steel API 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1
wall thickness wall thickness wall thickness wall thickness wall thickness wall thickness 4
1,6 mm 1,6 mm 1,6 mm 1,6 mm 1,6 mm 1,6 mm
B5 (0ºC/90ºC) C5 (0ºC/90ºC) E5 (0ºC/90ºC) F5 (0ºC/90ºC) G5 (0ºC/90ºC) H5 (0ºC/90ºC)
Carbon steelAPI
Carbon steelAPI Carbon steel API Carbon steel API Carbon steel API
Carbon steelAPI
5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1
wall thickness wall thickness wall thickness wall thickness wall thickness wall thickness 5
3,2 mm 3,2 mm 3,2 mm 3,2 mm 3,2 mm 3,2 mm
B6 (-46ºC/240ºC)C6 (-
46ºC/110ºC)
E6 (-46ºC/110ºC) F6 (-46ºC/110ºC) G6 (-46ºC/110ºC)
Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel ASTM A333 Gr 6 ASTM A333 Gr 6 ASTM A333 Gr 6 ASTM A333 Gr 6 ASTM A333 Gr 6
wall thickness wall thickness wall thickness wall thickness wall thickness
1,6 mm 1,6 mm 1,6 mm 1,6 mm 1,6 mm
E6R(-46ºC/110ºC) F6R (-46ºC/110ºC) G6R (-46ºC/110ºC)
Carbon steel Carbon steel Carbon steel ASTM A333 Gr 6 ASTM A333 Gr 6 ASTM A333 Gr 6
wall thickness wall thickness wall thickness
6
1,6 mm 1,6 mm 1,6 mm
B7 (0ºC/90ºC)
CuNi 90/10 (UNS
C70600) 20 bar
B7R (0ºC/90ºC)
CuNi 90/10 (UNS
7
C70600) 16 bar
A8 (0ºC/105ºC) C8 (-18ºC/54ºC) E8 (-18ºC/54ºC)
Carbon steel API Carbon steelAPI Carbon steel API 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1
8
Galvanized Galvanized Galvanized
B9 (0ºC/270ºC) C9 (0ºC/270ºC) E9 (0ºC/150ºC)
Carbon steelAPI
Carbon steelAPI Carbon steel API
5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1
wall thickness3,2
wall thickness wall thickness 9
3,2 mm 3,2 mm 3,2 mm
B10 (0ºC/240ºC) C10 (0ºC/240ºC) E10 (-15ºC/210ºC) F10 (0ºC/210ºC) G10 (-20ºC/210ºC) H10 (0ºC/175ºC)
Carbon steelAPI
Carbon steelAPI Carbon steel API Carbon steel API Carbon steel API
Carbon steelAPI
5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1
wall thickness wall thickness wall thickness wall thickness wall thickness wall thickness 1,6 mm 1,6 mm 1,6 mm 1,6 mm 1,6 mm 1,6 mm
G10P(10ºC/110ºC) H10P(0ºC/70ºC)
Carbon steel API Carbon steel
5L Gr B PSL 1API 5L Gr B
PSL 1
wall thickness wall thickness 1,6 mm (piggable)
1,6 mm(piggable)
E10R(0ºC/240ºC) F10R(0ºC/240ºC) G10R(0ºC/240ºC)
Carbon steel API Carbon steel API Carbon steel API 5L Gr B PSL 1 5L Gr B PSL 1 5L Gr B PSL 1
wall thickness wall thickness wall thickness
10
1,6 mm 1,6 mm 1,6 mm
B11 (0ºC/150ºC) C11 (0ºC/90ºC) E11 (0ºC/90ºC) F11 (0ºC/90ºC) G11 (0ºC/90ºC) H11 (0ºC/70ºC)
Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel
API 5L Gr BPSL 1
API 5L Gr BPSL 1
API 5L Gr BPSL 1
API 5L Gr BPSL 1
API 5L Gr BPSL 1
API 5L Gr BPSL 1
M e t a l l i c s
11
(organic coated) (organic coated) (organic coated) (organic coated) (organic coated) (organic coated)
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
22/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 22 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
B12 (0ºC/140ºC) C12 (0ºC/140ºC) G12 (0ºC/90ºC) J12 (0ºC/65ºC)
Super duplex steel Super duplexsteel
Super duplex steel Super duplex steel
ASTM A790 ASTM A790 ASTM A790 ASTM A790
(UNS S32760) (UNS S32760) (UNS S32760) (UNS S32760)
G12P (0ºC/90ºC)
Super duplex steel
ASTM A790
(UNS S32760)
12
(piggable)
B13 (0ºC/120ºC) C13 (0ºC/120ºC)Super duplex
steel Super duplex
steel ASTM A928 ASTM A928
13
(UNS S32750) (UNS S32750)
B14 (0ºC/70ºC) C14 (0ºC/70ºC) E14 (0ºC/70ºC) F14 (0ºC/70ºC) G14 (0ºC/70ºC) H14 (0ºC/70ºC)
Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel Carbon steel
API 5L Gr BPSL 1
API 5L Gr BPSL 1
API 5L Gr BPSL 1
API 5L Gr BPSL 1
API 5L Gr BPSL 1
API 5L Gr BPSL 1
(coated (coated (coated (coated (coated (coated
14
polyethylene) polyethylene) polyethylene) polyethylene) polyethylene) polyethylene)
B15 (10ºC/110ºC)
Carbon steel
Mariloy S-400
wall thickness
15
1,6 mm
B16(-46ºC/130ºC)
C16(-46ºC/130ºC)
E16(-46ºC/130ºC) G16(-46ºC/130ºC)
Duplex steel Duplex steel Duplex steel Duplex steel
ASTM A790 ASTM A790 ASTM A790 ASTM A790
(UNS S32760) (UNS S32760) (UNS S32760) (UNS S32760)
G16P(-46ºC/130ºC)
Duplex steel
ASTM A790
16
(UNS S32760)
B17 (0°C/120°C) E17 (0°C/90°C )Carbon steel API Carbon steel API
5L Gr B PSL 1 5L Gr B PSL 1
Wall thickness Wall thickness
17
6,4 mm 6,4 mm
G18 (0ºC/100ºC)
Carbon steel API
5L Gr B PSL 1
Wall thickness
18
1,6 mm
B19(-46°C/180°C)
G19 (-46ºC/70ºC)
Carbon steel Carbon steel
ASTM A 333 Gr 6 ASTM A 333 Gr 6
Wall thickness Wall thickness
19
3,2 mm 3,2 mm
C30 (0ºC/100ºC) E30 (0ºC/190ºC)H30
(-20ºC/100ºC)Carbon steel API Carbon steel API Carbon steel
API 5L Gr X65 PSL 1 5L Gr X65 PSL 1 5L Gr X65 PSL 1
(coated (coated (coated
Inconel 625) Inconel 625) Inconel 625)
H30P(0ºC/100ºC)
Carbon steelAPI
5L Gr X65 PSL 1
(coated
30
Inconel 625)
J31(-70ºC/123ºC)
Alloy steel
ASTM A 333 Gr 8
J31P(-70ºC/123ºC)
Alloy steel
M e t a l l i c
31
ASTM A 333 Gr 8
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
23/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 23 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
Class 125 150 300 600 900 1500 2500
Family A B C E F G H
B20 (0ºC/40ºC)
PVC ASTM
D1785 PVC 1120
20
B21 (0ºC/80ºC)
CPVC ASTM
F441 CPVC 4120
21
B22(90ºC/110PSIG)
(60º - 230 PSIG)
FRP ASTM F1173
condutive 150
22
psig
B23 (90ºC/150PSIG)
(60º - 230 PSIG)FRP ASTM F1173
condutive 225
23
psig
B24 (0ºC/120ºC)
FRP ASTM F1173
phenolic resin
condutive 150
24
psig
B25 (0ºC/80ºC)
RPVC - PVC
extruder reinforced
ext. wtih resin
poly and glass
N o n m e t a l l i c s
25
fiber
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
24/658
OFFSHORE PRODUCTION FACILITIES ENGINEERING GUIDELINES
VOLUME I – CORPORATE ENGINEERING REQUIREMENTSDR-ENGP-1.1-R.3 – Piping Standard and Material for Oil Production and Process Facilities PAGE: 24 of 24
PETROBRAS/E&P-ENGP/IPP/EISA Approved 29/11/2010 CORPORATE INFORMATION
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
25/658
N: REV:
P
CLIENT: SHEET:
TITLE:
Temp. RangeCorrosion
AllowanceClass Standard
0ºC / 90ºC (1,6 mm) 125 A4
TagSize
(in)Wall or class Ends
Size Tag
T-02A
T-02B
T-02A
T-02B
T-02A
16" - 20"
22" - 24" 0,281"
Elbow 90º JO-01
Elbow 45º JO-02
Tee TE-01
Cross CRUZ-01
Bushing BRE-01 6000
Half Coupling ML-01 3000
Plug BUJ-01 6000
Cap TAM-01
Union UN-01
Flex Un. UN FLEX-01 1"
Ins. Un. UN ISOL-01 1" - 1 1/2"
Coupling L-06
Short Nip.
Long Nip.
Red. Nip. C. NIPRC-01
Red. Nip. E. NIPRE-07
Red. Nip. C. NIPRC-04B
Red. Nip. E. NIPRE-10B
S. R. ELL 90º CRC-01
L. R. ELL 90º CRL-01
L. R. ELL 45º CRL-02
Tee TE-02
Red. Tee TRE-01
Conc . Red. REDC-01
Ecc. Red. REDE-01
Cap. TAM-02
Cross CRUZ-02
Weldolet WOL-01
FLG-01B 1/2" - 1 1/2" THD (FF)
FLG-02A SO (FF)
FLG-04B WN (FF)
FLG-05B BLIND (FF)
JPH-09 1/2" - 10" 1/16" (1,6mm)
JPH-10 12" - 24"
T-02B
Sch 10
API 5L Gr B PSL 1
welded (E=0,95)
Fenolic resin with neoprene
FF
1/8" (3,2mm)
Compressed non-asbestos
(aramida fiber and NBR)
Pipe
1/2" - 1 1/2" Sch 80THD
(Note 5)
BW
8" - 12"
T-01A
14"
TECHNICAL SPECIFICATION DR-ENGP-1.1
E&P 1 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
ASME B31.3 SFW-Fire Water (Fresh)
CODE Service
Item Material Ball
Pipes and fittings Valves
Description
2" - 6"
1/2" - 1 1/2"
Sch 40
Sch 20
API 5L Gr B PSL 1
seamless
or
welded (E=0,95)
Gate valve; class 125; FLG; FF; cast
iron.VG-34
14" - 24"
Gate (Note 4)
VG-36Gate valve; class 150; threaded;
bronze.
BW/THD
(Note 5)
THD
(Note 5)
Globe
1/2" - 1 1/2"
VG-35
Globe valve; class 125; FLG; FF; cast
iron.
2" - 12"
Butterfly valve; wafer; max.
pressure 250 PSIG; ductile iron,
Buna-N seat.
VB-09
VB-10
Butterfly valve; wafer; max.
pressure 250 PSIG; gear; ductile
iron, Buna-N seat.
Other
Angular valve for hydrant; with
adaptor for hose and cap; max.
working pressure 200 psig;
VGL-31
8" - 24"
150 ASTM A 105
2 1/2"
2" - 6"
12" - 24"
(Note 2) 1/2" - 1 1/4"ASTM A 193 Gr B7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Nut ASTM A 194 Gr 2H
Stud
2" - 24"Check valve, dual plate, wafer; class
125, FF, cast iron.
VB-02
Butterfly (Note 8)
2" - 10"
Butterfly valve; wafer; max.
pressure 150 PSIG; ductile iron,
Buna-N seat.
VB-01
VR-49
BW
ASTM A 105
Gate valve; class 125; FLG; FF;
gear; cast iron.
Globe valve; class 150; threaded;
bronze.
Check
VR-25
VGL-16
VGL-18
API 5L Gr B PSL 1
seamless
Check valve, swing type, class 200,
threaded, bronze.
Butterfly valve; wafer; max.
pressure 150 PSIG; gear; ductileiron, Buna-N seat.
API 5L Gr B PSL 1
seamless
ASTM A 234 Gr WPB
2" - 10"
1/2" - 1 1/2"
2" - 24"
Gasket(Note 10)
Flange(Notes 6 and 7)
F i t t i n g s
( N o t e s
1
a n d
9 )
T-01A
JI-02 1/2" - 24"
2" - 24"
1/2" - 1 1/2"
ASTM A 105
3000
3000
1/2" - 1 1/2"
1/2" - 4"
Wall Thickness
according to pipe
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
26/658
N: REV:
P
CLIENT: SHEET:
TITLE:
Temp. RangeCorrosion
AllowanceClass Standard
0ºC / 90ºC (1,6 mm)
125 A4
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Threaded connections must be weld sealed in case of vibration.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 Use weldneck flanges when directly connected to but-weld fittings.
8 For pressures above 150 psig, use VB-09 and VB-10.
9 Use Plug (BUJ-01) after drains and vents blocking.
10 Isolating joint see drawing on the appendix 15.
Max. Press. (psig)
NPS (1/2" -12")Temp. (ºC)
TECHNICAL SPECIFICATION DR-ENGP-1.1
E&P 2 of 132
CODE Service
ASME B31.3 SFW-Fire Water (Fresh)
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Branch Connections (Note 3)
90 190 90 135
150
Pressure / Temperature Rating
up to 66
Max. Press. (psig)
NPS (14" - 24")
up to 66 200
Temp. (ºC)
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
27/658
N: REV:
R
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
0ºC / 105ºC ______ 125 A8
TagSize
(in)Wall or class Ends
Size (in) Tag
T-02A
T-02B VE-10E
T-02A VE-17E
T-02B
Elbow 45º JO-08
Equal Tee TE-05
Red. Tee TRE-02
Cross CRUZ-05
Half Coupl ing ML-02
Red. Coupling LRE-01
Cap TAM-05
Union UN-04
Coupling L-04
Short Nip.
Long Nip.
Red. Nip. C NIPRC-04
Red. Nip. E NIPRE-10
Red. Nip. C NIPRC-04A
Red. Nip. E NIPRE-10A
S. R. Elbow 90º CRC-01
L. R. Elbow 90º CRL-01
L. R. Elbow 45º CRL-02
Tee TE-02
Red. Tee TRE-01
Conc. Red. REDC-01
Ecc. Red. REDE-01
Cap TAM-02
Cross CRUZ-02
Weldolet WOL-01
JPH-07 1/2" - 10" 1/16" (1,6mm)
JPH-08 12" - 24" 1/8" (3,2mm)JPH-09 1/2" - 10" 1/16" (1,6mm)
JPH-10 12" - 24"
JI-02 1/2" - 24"
FLG-04B
BLIND (FF)
WN (FF)
Globe (Note 4)
Check
VGL-18
1/2" - 12"FLG-05B
API 5L Gr B PSL 1
seamless
Gate valve; class 150; FLG; FF; carbonsteel.
T-05A
2" - 6"
8" - 12"
API 5L Gr B PSL 1
seamless
Ball valve; class 150; FLG; FF; carbon
steel.2" - 4"
Ball valve; class 150; FLG; FF; carbon
steel.
Ball valve; class 150; FLG; FF; gear;
carbon steel.
Sch 20
Sch 40
VE-22E
3000
VE-44
6" - 12"
BW
VR-127
VR-49
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
2" - 12"
1/2" - 1 1/2"
1/2" - 1 1/2"
Check valve, dual plate, wafer, class
125; FF; cast iron.
Check valve, swing type, class 200,
FLG, FF, bronze.
DR-ENGP-1.1
E&P 3 of 132
Pipes And Fittings (Notes 5 and 9) Valves
CODE Service
ASME B31.3 HWU-Utility Heating Water - Utilities; GW-Grey Water; SP-Tank Vent &Sounding Pipe (Notes 8 and 9); WW-Sewage Waste Water
Item Material
1/2" - 1 1/2" Sch 80 PLAINDescription
1/2" - 1 1/2"
Ball (Note 4)
API 5L GR B PSL 1
seamless
or
welded (E=0,85)
Gate (Note 4 )
2" - 10"Globe valve; class 125; FLG; FF; cast
iron.
Flange
(Note 6)150 ASTM A 105
1/2" - 12"
Other
Compressed non-asbestos(aramida fiber and NBR)Gasket
(Note 4)
VAG-08Globe valve, needle disc; 3000 psig;
threaded; male-female; stainless steel.
1/8" (3,2mm)
RF
FF
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Nut
ASTM A 193 Gr B7
ASTM A 194 Gr 2H
Stud(Note 2) 1/2" - 7/8"
SW
Pipe
F i t t i n g s
( N o t e s
1
a n d
3 )
ASTM A 105
2" - 12" BW
1/2" - 4"
ASTM A 105
VG-100
2" - 12"Gate valve; class 125; FLG; FF; cast
iron.VG-34
1/2" - 1 1/2"
Wall
thickness
according to
pipe
Fenolic resin with neoprene
T-05A
1/2" - 1 1/2"
PLAIN
ASTM A 234 Gr WPB
BW/PLAIN
JO-07Elbow 90º
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
28/658
N: REV:
R
CLIENT: SHEET:
TITLE:
Temp.
Ran e
Corrosion
AllowanceClass Standard
0ºC / 105 ºC ______
125 A8
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 Use niple THD X PLAIN and threaded cap (TAM-04) after drains and vents blocking.
4
5 Piping spools must be galvanized after manufacturing to ASTM A 123.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 For onshore facilities only, stub in connections may be used according to ASME B31.3.
8 Use Spec A8 only for vent in Naval Systems.
9
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
CODE Service
TECHNICAL SPECIFICATIONDR-ENGP-1.1
E&P 4 of 132
ASME B31.3HWU-Utility Heating Water - Utilities; GW-Grey Water; SP-Tank Vent &
Sounding Pipe (Notes 8 and 9); WW-Sewage Waste Water
Temp. (ºC) Max. press (psig) Temp. (ºC) Max. press (psig)
up to 65 200
80 194
Branch Connections (Note 7)
185105
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
On Naval Systems the wall thickness must be: DN ≤ 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN ≥ 10" - (0.500) XS.
Use flat face gasket (JPH-10) for gate, globe and check valves assembly. For ball valves use raised face gasket (JPH-07).
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
29/658
N: REV:
E
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
-100ºC / 370ºC ________ 150 B3
TagNPS
(in)Wall or Class Ends
T-11 1/2" - 1 1/2" Sch 40S PLAIN Size Tag
2" - 10" Sch 10S
12" Sch 40S
14" - 16" Sch 10S
18" - 20" Sch 40S
22" Sch 20
24" Sch 40S
26" - 28" 0.438"
30" Sch 10
32" Sch 20
34" Sch 30
Elbow 90º JO-23
Elbow 45º JO-24
Tee TE-15
Red. Tee TRE-10
Cross CRUZ-15
Hal f Coupl ing ML-09
Red. Coupling LRE-05
Cap TAM-19
Union UN-12
Coupling L-13
Short Nip.
Long Nip.
Red. Nip. C NIPRC-07
Red. Nip. E NIPRE-13
Red . N ip . C NIPRC-07A
Red. N ip . E NIPRE-13A
S.R.ELL 90º CRC-04 2" - 24"
L.R.ELL 90º CRL-07
L.R.ELL 45º CRL-08
Tee TE-21
Red. Tee TRE-16
Conc. Red. REDC-04
Ecc. Red. REDE-04
Cap TAM-25
Cross CRUZ-19
Weldolet WOL-04
FLG-51 1/2" - 1 1/2" SW (RF)
FLG-50A 1/2" - 24" BLIND (RF)
FLG-49A 2" - 24" WN (RF)
FLG-50B BLIND (RF)
FLG-49B WN (RF)
JE-04 1/2" - 6"
JE-05 8" - 24"
JE-06 26" - 34"
JI-01 1/2" - 34" 1/8" (3,2 mm)
(Notes 2) 1/2" - 1 1/2"
(Notes 2 and 20) 1/2" - 1 1/2"
(Notes 2) 1/2" - 1 1/2"
(Notes 2 and 20) 1/2" - 1 1/2"
6" - 24"Ball valve; fire tested; class 150;
FLG; RF; gear; stainless steel,
RPTFE® metal seat, -46°C to
Gate valve; class 150; FLG; RF;
stainless steel.
Globe valve; class 150; FLG; RF;
stainless steel.2" - 10"
2" - 4" VE-256
Ball valve; fire tested; class 150;
FLG; RF; gear; stainless steel,
TFE/P metal seat.
VE-255
VR-74
2" - 24"
VE-241
Ball valve; class 150; FLG; RF;
stainless steel, PEEK® seat, -
46°C to 220°C.
VE-242
Ball valve; class 150; FLG; RF;
gear; stainless steel, PEEK® seat,
-46°C to 220°C.
VE-246
2" - 4"
Ball valve; fire tested; class 150;
FLG; RF; stainless steel, RPTFE®
metal seat, -46°C to 150°C.
VE-247
VG-19
6" - 24"
BW
Stainless steel AISI 304 with flexible-graphite, with inner ring AISI 304
ASTM A 403 Gr WP 316L
1/2" - 1 1/2"
3000
Ball valve; fire tested; class 150;
FLG; RF; gear; stainless steel,
PEEK® metal seat, -46°C to
1/2" - 1 1/2"
2" - 4"
Gate valve; class 800; SW;stainless steel.
1/2" - 1 1/2"
Ball valve; fire tested; class 800;
SW; stainless steel, TFE/P metal
seat.
6" - 24"
Ball valve; fire tested; class 800;
SW; stainless steel, RPTFE ®
metal seat; -46°C to 150°C.
Ball valve; class 150; FLG; RF;
stainless steel, TFE/P seat.
Check
6" - 24"
Ball valve; fire tested; class 800;
SW; stainless steel, PEEK ® metal
seat, -46°C to 220ºC.
1/2" - 1 1/2"
VE-250
VE-251
VG-18
Gate (Note 4)
2" - 12"
Gate valve; class 150; FLG; RF;
gear; stainless steel.14" - 24"
26" - 34"
ASTM A 194 Gr 7
Globe
1/2" - 1 1/2"
Check valve; dual plate; wafer;
class 150; RF; stainless steel,
metal-metal; over 200ºC.
Check valve; horizontal; class
800; SW; stainless steel.VR-83
Other
VR-42
6" - 24"
6" - 24"Ball valve; class 150; FLG; RF;
gear; stainless steel, TFE/P seat.
VE-245
(Note 18)
2" - 4"
1/2" - 1 1/2"Ball valve; class 800; SW;
stainless steel, TFE/P seat.
VE-243
(Note 18)
Ball valve; class 150; FLG; RF;
gear; stainless steel, -46°C to
370°C.
VE-149
VE-230
2" - 4"
Ball valve; class 150; FLG; RF;
stainless steel, RPTFE® seat, -
46°C to 150°C.
VE-328
VE-329
Ball valve; class 150; FLG; RF;
gear; stainless steel, RPTFE®
seat, -46°C to 150°C.
6" - 24"
VE-240
Ball valve; class 800; SW;
stainless steel, PEEK® seat, -
46°C to 220ºC.
1/2" - 1 1/2"
Description
T- 30
(Note 18)BW
1/2" - 1 1/2"
Ball valve; class 800; SW;
stainless steel, RPTFE® seat, -
46°C to 150°C.
ASTM A 312 Gr TP 316L
seamless
ASTM A 358 Gr TP 316L 1 or 3
welded (E=1)
2" - 4"
Valves (Note 16)
Item Material Ball (Note 4)
DR-ENGP-1.1
E&P 5 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
SYSTEM
Service
ASME B31.3
F i t t i n g s
a n d
A c c e s s o r i e s
( N o t e s
1
a n d
5 )
F-Safety System and Flare (Note 11); FG-Fuel Gas (Note 9); IGN-Ignition Line; PC-Process (Corrosive
Hydrocarbon) (Note 10); CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite);IA-
Instrumention Air; H-Hydraulic Fluid; IG-Instrumention Gas; IN-Instrumention Nitrogen; D- Diesel (Note
7); JF-Aviation Kerosene; PW-Potable Water (Note 8); PWH-Hot fresh water (Note 8); BG-Inerte gas
(Notes 12 and 14); SP-Tank Vent & Sounding (Notes 14 and 15); DW- Distilled water; AM-Amine (Note
16).
Pipes and Fittings (Note 12 )
ASTM A 312 Gr TP 316L
seamless
2" - 34"
ASTM A 182 Gr F 316L
1/2" - 1 1/2"
ASTM A 182 Gr F 316L
TECHNICAL SPECIFICATION
Flange(Notes 6 and 12)
T-11
Pipe
SW
CODE
1/2" - 1 1/2"Ball valve; class 800; SW;
stainless steel, -46°C to 370°C.VE-231
2" - 4"Ball valve; class 150; FLG; RF;
stainless steel, -46°C to 370°C.VE-148
ASTM A 182 Gr F 316L
Fenolic resin with neoprene
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
VE-257
Stud
Check valve; dual plate; wafer;
class 150; RF; stainless steel;
Viton TBR-S seat; up to 200ºC.
VE-248
PLAIN
BW/PLAIN
VE-244
(Note 18)
VGL-10
Ball valve; fire tested; class 150;
FLG; RF; stainless steel, PEEK®
metal seat, -46°C to 220°C.
VE-249
VG-52
Ball valve; fire tested; class 150;
FLG; RF; stainless steel, TFE/P
metal seat.
VAG-26Globe valve, needle disc; 3000
psi; SW; stainless steel.1/2" - 1 1/2"
0,175" (4,4mm)
Stainless steel AISI 304
with flexible-graphite2" - 24"
RFGasket
(Note 19)
Nut
Wall
thickness
according topipe
150
1/2" - 4"
ASTM A 320 Gr L7
ASTM A 193 Gr B16
ASTM A 194 Gr 4/S3
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
30/658
N: REV:
E
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
-100ºC / 370ºC ________ 150 B3
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 On piping subjected to water hammer or requesting gradual opening and closing only gate valves must be used.
5 Use niple THD X PLAIN and threaded cap (TAM-14) after drains and vents blocking.
6 Flanges ≤ 1 1/2" may be used, if strictly necessary.
7 Use only downstream centrifuge.
8 When Classifier especifies metallic material, this Spec shall be used.
9 Use only downstream filters.
10 This Spec should only be used when recommended in appendix 5.
11 Pipes, connections and fittings larger than 24", only to be used in F - (Flare) service.
12 For inert gas used for purge of cargo and ballast pumps in Naval Systems use only B3.
13 For sounding pipe in Naval Systems use only B3.
14 On Naval Systems the wall thickness must be: DN ≤ 2" - Sch 80 /// 2" < DN < 10" - Sch 40 /// DN ≥ 10" - (0.500) XS.
15 When requerid Fully Tight valve (VET), see types in appendix 14.
16 Inlet from rich Amine flash drum and outlet of Amine stripper reflux drum.
17 From -101ºC to -30ºC material shall be solution heat treated.
18 Use only for AM - Amine.
19 Isolating joint see drawing on the appendix 15.
20
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
221
Max. Press. (PSIG)
For SDV's and it's by pass (if existing) or when design especified, "fire tested" ball valves must be used. ASTM A 193 Gr B16 stud bolts and ASTM A 194
Gr 7 nuts for this valves assembly shall be Zn-Ni coated.
Branch Connections (Note 3)
130
161205
CODE
238
110
100
TECHNICAL SPECIFICATIONDR-ENGP-1.1
6 of 134
154
E&P
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND MARINE
189 370
192
Pressure / Temperature Rating
Temp. (ºC)
from -100 up to 38
Max. Press. (PSIG)
50
150 174230
Temp. (ºC)
ASME B31.3
F-Safety System and Flare (Note 11); FG-Fuel Gas (Note 9); IGN-Ignition Line; PC-Process (Corrosive
Hydrocarbon) (Note 10); CNI-Corrosive Chemical Injection (Except Sodium Hypoclorite);IA-
Instrumention Air; H-Hydraulic Fluid; IG-Instrumention Gas; IN-Instrumention Nitrogen; D- Diesel (Note
7); JF-Aviation Kerosene; PW-Potable Water (Note 8); PWH-Hot fresh water (Note 8); BG-Inerte gas
(Notes 12 and 14); SP-Tank Vent & Sounding (Notes 14 and 15); DW- Distilled water;
AM-Amine (Note 16).
Service
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
31/658
N: REV:
G
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
0ºC / 350ºC (1,6 mm) 150 B4
TagSize
inWall or Class Ends
Size Tag
T-02A
T-02B
T-02A
14"
16" - 18"
20" - 24" Sch 20
Elbow 90º JO-07
Elbow 45º JO-08
Tee TE-05
Red. Tee TRE-02
Cross CRUZ-05
Half Coupling ML-02
Red. Coupling LRE-01
Cap TAM-05
Union UN-04
Coupling L-04
Short Nip.
Long Nip.
Red. Nip. C NIPRC-04
Red. Nip. E NIPRE-10
Red. Nip. C NIPRC-04A
Red. Nip. E NIPRE-10A
S.R.ELL 90º CRC-01
L.R.ELL 90º CRL-01
L.R.ELL 45º CRL-02
Tee TE-02
Red. Tee TRE-01
Conc. Red. REDC-01
Ecc. Red. REDE-01
Cap TAM-02
Cross CRUZ-02
Weldolet WOL-01
FLG-05E 1/2" - 1 1/2" SW (RF)
FLG-05A 1/2" - 24" BLIND (RF)
FLG-04A 2" - 24" WN (RF)
F i t t i n g s
( N o t e s
1
a n d
4 )
ASTM A 105
BW/PLAIN
Wall Thickness
according to pipe
PLAIN
ASTM A 105
14" - 24"Gate valve; class 150; FLG; RF;
gear; carbon steel.
TECHNICAL SPECIFICATION
Service
8" - 24"
1/2" - 6"
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
E&P
Sch 40
07 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Pipes and Fittings (Note 4) Valves (Note 6)
DR-ENGP-1.1
CODE
150
Nut ASTM A 194 Gr 2H(Note 2)
Stud ASTM A 193 Gr B7
Gasket
Flange
(Note 5)
JE-05
ASTM A 105
ASME B31.3 HF-Hot Fluid; HWP-Process Heating Water; S-Steam; SC-Steam Condensate
8" - 12"
T-05A API 5L Gr B PSL 1 seamless
Item Material Ball
Description
BW
Pipe
1/2" - 1 1/2" Sch 80 PLAIN
2" - 6"
T-02B
Sch 20
API 5L Gr B PSL 1 seamless or
welded
(E=0,85)
API 5L Gr B PSL 1 welded
(E=0,85)
Sch 10
Globe
1/2" - 1 1/2"Globe valve; class 150; FLG; RF;
carbon steel.VGL-20
VR-56
2" - 12"Gate valve; class 150; FLG; RF;
carbon steel.
Gate
1/2" - 1 1/2"Gate valve; class 800; SW; carbon
steel.VG-45
VG-39A
VG-39
Check valve; horizontal; piston;
class 800; SW; carbon steel.
Other
Globe valve, needle disc; 3000
PSI; SW; carbon steel.VAG-17
VR-77
2" - 24" VR-76
3000 SW
1/2" - 1 1/4"
Check valve; dual plate; wafer;
class 150; RF; carbon steel; metal-
metal (over 200°C).
2" - 24"
Check valve; dual plate; wafer;class 150; RF; carbon steel; Viton
seat TBR-S (up to 200°C).
Check
1/2" - 1 1/2"
1/2" - 1 1/2"
JE-04
0,175" (4,4mm) RFStainless steel AISI 304 with
flexible-graphite, with inner ring
AISI 304
Stainless steel AISI 304 with
flexible-graphite
API 5L Gr B PSL 1
seamless
ASTM A 234 Gr WPB
T-05A
2" – 24" BW
1/2" - 4"
1/2" - 1 1/2"
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
32/658
N: REV:
G
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
0ºC / 350ºC (1,6 mm) 150 B4
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Use niple THD X PLAIN and threaded cap (TAM-01) after drains and vents blocking.
5 Flanges ≤ 1 1/2" may be used, if strictly necessary.
6
200
250
When requerid Fully Tight valve (VET), see types in appendix 14.
200
174
147
121
E&P 08 of 134
TECHNICAL SPECIFICATION
300
350
Temp. ºC
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
DR-ENGP-1.1
Pressure / Temperature Rating
284
100
up to 38
50
251
Temp. ºC
110
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
CODE Service
ASME B31.3HF-Hot Fluid; HWP-Process Heating Water; S-Steam; SC-Steam
Condensate
Max. Press. (PSIG)
278
256
Branch Connections (Note 3)
Max. Press. (PSIG)
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
33/658
N: REV:
G
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
0ºC / 90ºC (3,2 mm) 150 B5
TagSize
(in)
Wall or
ClassEnds
T-05A 3/4" XXS PLAIN Size Tag
T-02A
Half Coupling ML-03 6000 SW
Short Nip.
Long Nip.
S.R.ELL 90º CRC-01
L.R.ELL 90º CRL-01
L.R.ELL 45º CRL-02
Tee TE-02
Red. Tee TRE-01
Conc. Red . REDC-01
Ecc. Red. REDE-01
Cap TAM-02
Cross CRUZ-02
Weldolet WOL-01
FLG-13 WN (RTJ)
FLG-15 BLIND (RTJ)
FLG-04A WN (RF)
FLG-04B PE (FF)
FLG-05A BLIND (RF)
FLG-05B BLIND (FF)
2" - 4" 600Butterfly
F i t t i n g s a n d
A c c e s s o r i e s
( N o t e
1 )
ASTM A105
API 5L Gr B PSL 1
seamlessXXS
ASTM A 105
ASTM A 234 Gr WPB
T-05A
Flange
(Note 4)ASTM A 105
Carbon steel coated Zn-Ni max.hardness 90 Brinell
Stud
2" - 6" 150
Gasket
(Note 2)
JPH-07 2" - 6"1/16"
(1,6mm)
JA-01 2" - 4" 600 Oval
ASME B31.3 FP-Production and drilling fluid
Pipes and Fittings
Pipe
Item Material
T-02BSch 80
API 5L Gr B PSL 1 seamless
API 5L Gr B PSL 1 welded
(E=0,85)
Valves
description
VE-48D3/4"Ball valve; class 800; SW; carbon
steel.
Ball
CODE Service
TECHNICAL SPECIFICATION
E&P
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
DR-ENGP-1.1
09 of 134
Gate (Note 4)
2 1/16" - 4 1/16"Gate valve; abrasive; FLG; RTJ;
carbon steel; API 2000 PSIG; CWP.VG ABRAS-04
Globe
2" - 6"Check valve; dual plate; wafer;
class 150; carbon steel; Viton seat.VR-35
RFCompressed non-asbestos
(aramida fiber and NBR)
Check
(Note 2) 5/8" - 3/4"Nut ASTM A 194 Gr 2H
ASTM A 193 Gr B7
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
2" - 6"
BW
PLAIN
BW
Wall
thickness
according to
pipe
2" - 6"
3/4"
2" - 6"
Butterfly valve; wafer; max.
pressure 150 PSIG; ductile iron,
Buna-N seat.
VB-03
2" - 6"
Butterfly valve; wafer; max.
pressure 250 PSIG; ductile iron,
Buna-N seat.
VB-09
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
34/658
N: REV:
G
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
0ºC / 90ºC (3,2 mm) 150 B5
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts, nuts and gaskets must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 In VG ABRAS-04 assembly use FLG-13 (RTJ) flange.
CODE Service
ASME B31.3 FP-Production and drilling fluid
Pressure / Temperature Rating
Temp. (ºC) Max. Press. (PSIG) Temp.(ºC) Max. Press. (PSIG)
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
TECHNICAL SPECIFICATION DR-ENGP-1.1
E&P 10 of 134
90 261
up to 38 284
50 278
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Branch Connections (Note 3)
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
35/658
N: REV:
I
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
-46ºC /
240ºC(1,6 mm) 150 B6
TagSize
(in)
Wall or
ClassEnds
1/2" - 3/4" Sch 160 Size Tag
1" - 1 1/2"
2" - 3"
4" - 6" Sch 40
8" - 12" Sch 20
14"
16" - 20"
22" - 24" 0,312"
26" - 28" Sch 10
30" 0,344"
32 - 34" STD
36" 0.406"
Elbow 90º JO-17
Elbow 45º JO-18
Equal Tee TE-12
Red. Tee TRE-08 1/2" - 1 1/2"
Cross CRUZ-12
Half Coupling ML-07
Red. Coupling LRE-04
Cap TAM-12
Union UN-09
Coupling L-09
Elbow 90º JO-13
Elbow 45º JO-14
Equal Tee TE-09
Red. Tee TRE-05
Cross CRUZ-09
Half Coupling ML-05
Red. Coupling LRE-03
Cap TAM-09
Union UN-07
Coupling
Short Nip.
Long Nip.
Red. Nip. C NIPRC-05
Red. Nip. E NIPRE-16
Red. Nip. C NIPRC-05A
Red. Nip. E NIPRE-16A
S.R.ELL 90º CRC-02 2" - 24"
L.R.ELL 90º CRL-03L.R.ELL 45º CRL-04
Tee TE-08
Red. Tee TRE-04
Conc. Red. REDC-02
Ecc. Red. REDE-02
Cap TAM-08
Cross CRUZ-08
Weldolet WOL-02
FLG-45 1/2" - 1 1/2' SW (RF)
FLG-23A 1/2" - 24" BLIND (RF)
FLG-22A 2" - 24" WN (RF)
FLG-23B BLIND (RF)
FLG-22B WN (RF)
JE-05 8" - 24"
JE-06 26" - 36"
26" - 36"Ball valve; class 150; FLG; RF; gear; carbon
steel, RPTFE® seat, up to 150ºC.VE-332A
VE-302B
6" - 24"
Ball valve; fire tested, class 150; FLG; RF;
gear; carbon steel, RPTFE® seat, up to
150ºC.
VE-301
Ball valve; fire tested, class 800; SW; carbon
steel, PEEK® seat, over 150°C.VE-302C
VE-298
Ball valve; fire tested, class 150; FLG; RF;
carbon steel, PEEK® seat, over 150°C.VE-303
6" - 24"Ball valve; fire tested, class 150; FLG; RF;
gear; carbon steel, PEEK® seat, over 150°C.VE-304
L-08
Ball valve; fire tested, class 800; SW; carbon
steel, RPTFE® seat, up to 150ºC.VE-299C
1" - 1 1/2"Ball valve; fire tested, class 800; SW; carbon
steel, RPTFE® seat, up to 150ºC.VE-299B
2" - 4"Ball valve; fire tested, class 150; FLG; RF;
carbon steel, RPTFE® seat, up to 150ºC. VE-300
VE-301A
VE-332
Valves (Note 8)
Item Material
1" - 1 1/2"Ball valve; class 800; SW; carbon steel,
RPTFE® seat, up to 150ºC.VE-330B
Pipes and Fittings (Note 5)
PipeBall valve; class 150; FLG; RF; carbon steel,
RPTFE® seat, up to 150ºC.VE-331
2" - 36"
1/2" - 3/4"
1/2" - 3/4"
1" - 1 1/2"
6" - 24"
VE-298A
Globe
6000
Ball valve; class 150; FLG; RF; gear; carbon
steel, PEEK® seat, over 150°C.
CODE
Check valve; dual plate; wafer; class 150;
RF; carbon steel; Viton TBR-S seat (up to
200°C).
VR-53
1/2" - 1 1/2"Check valve; horizontal; piston; class 800;
SW; carbon steel.VR-52
F i t t i n g s a n d
A c c e s s o r i e s
( N o
t e s
1
a n d
5 )
1/2" - 4"
T-09
1/2" - 1 1/2"
TECHNICAL SPECIFICATION DR-ENGP-1.1
E&P 11 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Service (Note 6)
ASME B31.3F-Safety System and Flare; G-Glycol; GL-Refrigerated Liquified Petroleum
Gases in Low Temperature; P-Process (non-corrosive hydrocarbon )
2" - 4"
T-07A
T-08
Sch 10
Sch 80
ASTM A 671 Gr CC 60
CL 22 welded (E=1)
ASTM A 333 Gr 6
seamless
T-09
2" - 4"
1" - 1 1/2"
Ball valve; class 150; FLG; RF; carbon steel,
PEEK® seat, over 150°C.
PLAIN
BW
6" - 24"Ball valve; class 150; FLG; RF; gear; carbon
steel, RPTFE® seat, up to 150ºC.
Ball valve; class 800; SW; carbon steel,
PEEK® seat, over 150°C.
SW
Ball
Description
VE-297
1/2" - 3/4" Ball valve; class 800; SW; carbon steel,PEEK® seat, over 150°C.
VE-296C
1/2" - 3/4"Ball valve; class 800; SW; carbon steel,
RPTFE® seat, up to 150ºC.VE-330C
VE-296B
26" - 36"Ball valve; class 150; FLG; RF; gear; carbon
steel, PEEK® seat, over 150°C.
1/2" - 3/4"
3000
26" - 36"
Ball valve; fire tested, class 150; FLG; RF;
gear; carbon steel, RPTFE® seat, up to
150ºC.
ASTM A 350 Gr LF2 CL 1
1/2" - 3/4"
0,175" (4,4mm) RFStainless steel AISI 304 with
flexible-graphite, with inner ring
AISI 304
Wall
thicknessaccording to
pipe
2" - 24"
2" - 10"
Check
26" - 36"
Stainless steel AISI 304 with
flexible-graphite
Other
Check valve; dual plate; wafer; class 150;
RF; carbon steel; metal-metal (over 200°C).VR-71A
150 ASTM A 350 Gr LF2 CL 12" - 24"
Stud(Note 2)
ASTM A 320 Gr L7
ASTM A 194 Gr 4/S31/2" - 1 1/2"
Globe valve, needle disc; 3000 PSI; SW;
carbon steel.VAG-21
Flange
(Note 7)
1/2" - 1 1/2"Nut
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
26” - 36”
VR-78
(Note 4)Gasket
JE-04 1/2" - 6"
1" - 1 1/2"Ball valve; fire tested, class 800; SW; carbon
steel, PEEK® seat, over 150°C.
VR-53A
Check valve; dual plate; wafer; class 150;
RF; carbon steel; metal-metal (over 200°C).VR-71
VGL-22
26" - 36"Ball valve; fire tested, class 150; FLG; RF;
gear; carbon steel, PEEK® seat, over 150°C.VE-304A
2" - 4"
Check valve; globe; with damping piston;class 150; FLG; RF; Viton TBR-S seat (up to
200°C).
BW/PLAIN
PLAIN
ASTM A 333 Gr 6
seamless
ASTM A 420 Gr WPL6
2" - 24"
BW
Check valve; dual plate; wafer; class 150;
RF; carbon steel; Viton TBR-S seat (up to
200°C).
26" - 36"
Globe valve; class 150; FLG; RF; carbon
steel.
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
36/658
N: REV:
I
CLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
-46ºC /
240ºC(1,6 mm) 150 B6
Notes:
1 Instrument, drains and vents connections shall be according to appendix 1 to 4.
2 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
3 For onshore facilities only, stub in connections may be used according to ASME B31.3.
4 Where pulsating flow exists.
5 Use niple THD X PLAIN and threaded cap (TAM-07 or TAM-16) after drains and vents blocking.
6 Charpy impact test is required for low temperature services materials (-46ºC / -15ºC).
7 Flanges ≤ 1 1/2" may be used, if strictly necessary.
8
F-Safety System and Flare; G-Glycol; GL-Refrigerated Liquified Petroleum
Gases in Low Temperature; P-Process Hydrocarbon (non-corrosive)
TECHNICAL SPECIFICATION
E&P
110
DR-ENGP-1.1
Max. Press. (PSIG)
251
Temp.(ºC)
Pressure / Temperature Rating
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
240 180
Branch Connections (Note 3)
When requerid Fully Tight valve (VET), see types in appendix 14.
200
50
100
200
256
278
Temp. (ºC) Max. Press. (PSIG)
Service (Note 6)
-46 / 38 284
CODE
ASME B31.3
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
12 of 134
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
37/658
N: REV:
CCLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
0ºC / 90ºC ___ 150 B7
Size Tag
1/2" 16
3/4" 25
1" 30
1 1/4" 38
1 1/2" 44,5
2" 57
2 1/2" 76,1
3" 88,9
4" 108
6" 159
8" 219,1
10" 267
12" 323,9
14" 368
16" 419
18" 457,2
20" 508
24" 610
28" 711
32" 813
36" 914
Elbow 90° JO-92
Elbow 45° JO-93
Equal Tee TE-91
Coupling L-91
Union UN-91
Cap TAM-91
Red.Coupling F LREFF-91
Red. Coupling M LREMF-91 M.UCxF.UC
Sockolet SKL-91 UC
Conc. F CONF-91 F.NPTxF.UC
Conc. M CONM-91 M.NPTxF.UC
Fem. Un. Con. UNADF-91 F.UCxF.NPT
Male Un. Con. UNADM-91 M.NPTxNPT
Male Niple Con. NIPADM-91 M.NPTxM.UC
Fem. Niple Con. NIPADF-91 F.NPTxM.UC
BP/SPR. NPT BRE-91 M.UCxF.NPT
Plug BUJ-91 NPT
Male Niple NIPM-91 M.NPT
Thredolet THL-91 F.NPT
L.R.ELL 90º CRL-92
L.R.ELL 45º CRL-93
Tee TE-93
Red. Tee TRE-93
Conc. Red. REDC-91
Ecc. Red. REDE-90
Cap TAM-93
Weldolet WOL-90
FLG-90 SO (RF)
FLG-92 WN (RF)
FLG-93 BLIND (RF)
FLG-92A WN (RF)
FLG-93A BLIND (RF)
VIR- 03 WNSE
FLG- 132 WNBF
JPH-08
JI-01
Stub Ends1/2" - 36"
Cu-Ni 90/10
(UNS C70620)
Pressure 20 Bar
(EEMUA 145)
ASTM A 105 (EEMUA 145)
Flange
Backing Flange
26" - 36"
2" - 24"
1/2" - 1 1/2"
2" - 24"
F i t t i n g s a n d
A c c e s s o r i e s
( N o t e
1 )
1/2" - 1 1/2"
___
1/2" - 2"
1/2" - 1 1/2"
BW
Female
capilary
2" - 36"
Wall thickness
according to
pipe
150
2" - 24"
Check valve; dual plate; wafer; class
150; RF; carbon steel; Viton seat.
VB-19A
VR-42A
VB-18
VB-19
Butterfly
5,5
2,5
VGL-16
VR-251/2" - 1 1/2"Check valve; swing type; class 200;
threaded; brass.
2,5
ASME B31.3 FW-Fire Water (Aerated Sea Water)
Pipes and Fittings (Note 2)
Wall or
Class Ends Material
20 Bar
Od(mm)
TECHNICAL SPECIFICATION
T-90
T-91
Item Tag
Pipe
T-91 / T-92
T-92
Size(in)
CODE
E&P
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Service (Notes 4 and 5)
Valves (Note 7)
Ball
Description
DR-ENGP-1.1
13 of 134
4,5
3,5
2,0
2,5
2,5
PLAIN
2,5
2,5
Cu-Ni 90/10 (UNS C70620)
EEMUA 144 seamless or
welded (E=1)
9,0
17,0
13,0
Cu-Ni 90/10 (UNS C70620)
EEMUA 144 seamless
Gate valve; class 150; FLG; RF; gear;
stainless steel.
Gate valve; class 200; threaded; bronze.
2,0
7,0
19,0
9,5
8,01/2" - 1 1/2"
28" - 36"
15,0
BW
Gate
11,0
3,0
2" - 12"Gate valve; class 150; FLG; RF; stainless
steel.
Globe
VG-19
VG-19A
Cu-Ni 90/10
1/2" - 1 1/2"
Other
Butterfly valve; flanged; max. pressure
250 PSIG; RF; gear; ductile iron, Nylon
11 coated disc, Viton seat.
2" - 6"
Globe valve; class 150; FLG; RF; carbon
steel.
Angular valve for hydrant; with adaptorfor hose and cap; max. working pressure
200 PSIG; threaded; bronze.
2 1/2"
1/2" - 36"
1/2" 1 1/2"ASTM A 194 GR 2H
Fenolic resin with neoprene1/8" (3,2mm)
Nut(Note 3)
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Stud ASTM A 193 GR B7
VG-36
14" - 24"Gate valve; class 150; FLG; RF; gear;
stainless steel.
28" - 36"
Check
VGL-03
VGL-31
Globe valve; class 200; threaded; brass.
Cu-Ni 90/10 (UNS C70620)
EEMUA 144 welded (E=1)
2" - 10"
Check valve; dual plate; wafer; class
150; RF; carbon steel; Viton seat.VR-42
Cu-Ni 90/10
(UNS C70620)
Pressure 20 Bar
(EEMUA 146)
28" - 36"
8" - 24"
Butterfly valve; wafer; max. pressure
250 PSIG; gear; ductile iron, Nylon 11
coated disc, Viton seat.
Butterfly valve; wafer; max. pressure
250 PSIG; ductile iron, Nylon 11 coateddisc, Viton seat.
VG-18
Gasket
(Note 6)
RF
12" - 36"
Compressed non-asbestos
(aramida fiber and NBR)1/16" (1,6mm)1/2" - 10"JPH-07
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
38/658
N: REV:
CCLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
0ºC / 90ºC ___ 150 B7
1 Instrument, drains and vents connections shall be according to appendix 2 to 4.
2 Piping, connections and flanges should be specified according EEMUA 144/145/146.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 This Spec must be used only for offshore facilities. Use Spec B10 for onshore facilities.
5 Use Spec B24 for fixed platform and uninhabited.
6 Isolating joint see drawing on the appendix 15.
7
ASME B31.3 FW-Fire Water (Aerated Sea Water)
TECHNICAL SPECIFICATION
Max. Press. (PSIG)
DR-ENGP-1.1
E&P 14 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Pressure / Temperature Rating
CODE Service (Notes 4 and 5)
Temp. (ºC) Temp. (ºC)
up to 90 290
Max. Press. (PSIG)
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
When requerid Fully Tight valve (VET), see types in appendix 14.
Notes:
Branchs Connections
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
39/658
N: REV:
E
CLIENT: SHEET:
TITLE:
Temp. RangeCorrosion
AllowanceClass Standard
0ºC / 90ºC ___ 150 B7R
Size Tag
1/2" 16
3/4" 25
1" 30
1 1/4" 38
1 1/2" 44,5
2" 57
2 1/2" 76,1
3" 88,9
4" 108
6" 159
8" 219,1
10" 267
12" 323,9
14" 368
16" 419
18" 457,2
20" 508
24" 610
28" 711
32" 813
36" 914
Elbow 90° JO-92
Elbow 45° JO-93
Equal Tee TE-91
Coupling L-91
Union UN-91
Cap TAM-91
Red. Coupling F LREFF-91
Red. Coupling M LREMF-91 M.UC.xF.UC
Sockolet SKL-91 UC
Female Con. CONF-91 F.NPTxF.UC
Male Con. CONM-91 M.NPTxF.UC
Fem. Un. Con. UNADF-91 F.UCxF.NPT
Male. Un. Con. UNADM-91 M.UCxF.NPT
Male Niple Con. NIPADM-91 M.NPTxM.UC
Fem. Niple Con. N IPADF-91 F.NPTxM.UC
BP/SPR.NPT BRE-91 M.UCxF.NPT
Plug BUJ-91 NPT
Male Nip. NIPM-91 M.NPT
Thredolet THL-91 F.NPT
L.R.ELL 90º CRL-92
L.R.ELL 45º CRL-93
Tee TE-93
Red. Tee TRE-93
Conc. Red REDC-91
Ecc. Red REDE-90
Cap TAM-93
L.R.EII 90º CRL-94
L.R.EII 45º CRL-95
Tee TE-94
Red. Tee TRE-94
Conc. Red REDC-92
Ecc. Red REDE-91
Cap TAM-94
Weldolet WOL-90
FLG-92 WN (RF)
FLG-93 BLIND (RF)
FLG-94 WN (RF)
FLG-95 BLIND (RF)
FLG-94A WN (RF)
FLG-95A BLIND (RF)
VIR-03 WNSE
FLG-132 WNBF
JPH-07
JPH-08
JI-01
1/2" - 36"
150Cu-Ni 90/10
(UNS C7060X)
Pressure 16 Bar
(EEMUA 145)
Stub Ends
Backing Flange ASTM A 105 (EEMUA 145)
SO (RF)
6" - 24"
2" - 4"
1/2" - 1 1/2"
Gasket
(Note 6)
2" - 6"
Butterfly valve; wafer; max. pressure 250
PSIG; ductile iron, Nylon 11 coated disc,
Viton seat.
Gate valve; class 150; FLG; RF; stainless
steel.
28" - 36"
2" - 10"
2" - 12"
Globe valve; class 150; FLG; RF; carbon
steel.
Check valve; dual plate; wafer; class 150;
RF; stainless steel; Viton seat.
Globe
VG-18
2,5
5,5
2,5
Butterfly valve; max. pressure 150 PSIG;
RF; gear; ductile iron, Nylon 11 coated
disc, Viton seat.
4,5
2,5
13,5
6,5
BW
Female capilary
8" - 24"
1/2" - 1 1/2"
Butterfly (Notes 7, 10 and 11)
2 1/2"
Butterfly valve; flanged; max. pressure
250 PSIG; RF; gear; carbon steel, Nylon
11 coated disc, Viton seat.
8" - 24"
VB-11
Butterfly valve; wafer; max. pressure 150
PSIG; ductile iron, Nylon 11 coated disc,
Viton seat.
T-91
T-62
7,0
15,5
12
8,5
3,0
4,0
10,5
T-61 / T-62
1/2" - 10" Compressed non-asbestos
(aramida fiber and NBR)
Fenolic resin with neoprene1/8" (3,2mm)
1/16" (1,6mm)
RF
ASTM A 194 Gr 2H
12" - 36"
BW
ASTM A 193 Gr B7
Cu-Ni 90/10
(UNS C70620)
EEMUA 144 seamless
Cu-Ni 90/10
(UNS C70620)
EEMUA 144 seamless or welded
(E=1)
Cu-Ni 90/10
(UNS C70620)
EEMUA 144 welded (E=1)
PLAIN
Cu-Ni 90/10
Cu-Ni 90/10
(UNS C7060X)
Pressure 20 Bar
(EEMUA 145)
3,0
VB-29A
VB-26
Butterfly valve; wafer; max. pressure 150
PSIG; gear; aluminum-bronze, Ni/Al/Br
disc, Viton seat.
Butterfly valve; wafer; max. pressure 150
PSIG; aluminum-bronze, Ni/Al/Br disc,
Viton seat.
VB-25
28" - 36"
12" - 24"
2" - 10"
Butterfly valve; flanged; max. pressure
150 PSIG; RF; gear; aluminum-bronze,
Ni/Al/Br, Viton seat.
VB-26A
1/2" - 1 1/2'
Pipe
2,0
2,5
8,0
Wall thickness
according to
pipe
2,0
2,5
2,5
T-90
Ball
VG-36Gate valve; class 200; threaded; bronze.
Description
Gate
CODE Service
ASME B31.3 BR -Bilge (Note 7); FL-Foam Line (Note 4); FW-Fire Water (Aerated Sea Water) (Note 5);
SW-Aerated Sea Water (Naval System) (Note 8)
Pipes and Rattings (Note 2)
16 Bar
Valves (Note 9)
Item EndsTagSize
(in)
Od
(mm)
Wall or ClassMaterial
DR-ENGP-1.1
15 of 134E&P
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES AND
MARINE SYSTEM
VGL-161/2" - 1 1/2" Globe valve; class 200; threaded; brass.
VG-19A
VG-19
VGL-31
Check
Angular valve for hydrant; with adaptor
for hose and cap; max. working pressure
200 psig; threaded; bronze.
VGL-03
28" - 36"
14" - 24"Gate valve ; class 150; FLG; RF; gear;
stainless steel.
Gate valve; class 150; FLG; RF; gear;stainless steel.
28" - 36"Check valve; dual plate; wafer; class 150;
RF; stainless steel; Viton seat.VR-42A
Check valve; swing; type; class 200;
threaded; bronze.VR-25
2" - 24" VR-42
1/2" - 1 1/2"
2" - 10"
Cu-Ni 90/10
(UNS C7060X)
Pressure 16 Bar
(EEMUA 146)
28" - 36"
Butterfly valve; flanged; max. pressure
250 PSIG; RF; gear; ductile iron, Nylon 11
coated disc, Viton seat.
28" - 36"
Butterfly valve; flanged; max. pressure
250 PSIG; RF; gear; carbon steel, Nylon
11 coated disc, Viton seat.
Butterfly valve; wafer; max. pressure 250
PSIG; gear; ductile iron, Nylon 11 coated
disc, Viton seat.
Cu-Ni 90/10
(UNS C7060X)
Pressure 20 Bar
(EEMUA 146)
1/2" - 36"
(Note 3) 1/2" - 1 1/2"Nut
Stud
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
2" - 36"
VB-1212" - 24"
Butterfly valve; wafer; max. pressure 150
PSIG; gear; ductile iron, Nylon 11 coated
disc, Viton seat.
VB-19A
VB-29
VB-18
VB-12A2" - 4"
VB-19
26" - 36"
F i t t i n g s a n d
A c c e s s o r i e s
( N o t e
1 )
1/2" - 2"
1/2" - 1 1/2"
Flange(Note 2)
FLG-90
6" - 36"
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
40/658
N: REV:
ECLIENT: SHEET:
TITLE:
Temp. RangeCorrosion
AllowanceClass Standard
0ºC / 90ºC ___ 150 B7R
Notes:
1 Instrument, drains and vents connections shall be according to appendix 2 to 4.
2 Piping, connections and flanges should be specified according EEMUA 144/145/146.
3 Bolts and nuts must be Zn-Ni coated, according to appendix 10.
4 This Spec must be used only for offshore facilities. Use Spec B10 for onshore facilities.
5 Use Spec B24 for fixed platform and uninhabited.
6 Isolating joint see drawing on the appendix 15.
7 For BR, use VB-25, VB-26 and VB-26A.
8 Use only at Naval System, for generators and inert gas seal.
9
10
11 Diaphragm valve should be used according Project Engineer.
up to 90 230
THE DATA OR PARTS THERE OF, ARE PETROBRAS PROPERTY AND THUS MUST NOT BE USED IN ANY WAY WITHOUT ITS PERMISSION
Branchs Connections
Pressure / Temperature Rating
Temp. (ºC) Max. Press (PSIG) Temp. (ºC) Max. Press (PSIG)
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
CODE Service
ASME B31.3 BR -Bilge (Note 7); FL-Foam Line (Note 4); FW-Fire Water (Aerated Sea Water) (Note 5);
SW-Aerated Sea Water (Naval System) (Note 8)
Use VB-29 and VB-29A, flanged only at sea chest.
DR-ENGP-1.1
E&P 16 of 134
When requerid Fully Tight valve (VET), see types in appendix 14.
TECHNICAL SPECIFICATION
-
8/20/2019 DR ENGP 1.1 R.3piping Engineering
41/658
N: REV:
JCLIENT: SHEET:
TITLE:
Temp.
Range
Corrosion
AllowanceClass Standard
0ºC / 240ºC
(Note 16)(3,2 mm) 150 B9
TagSize
(in)Wall or Class Ends
1/2" - 3/4" XXS Size Tag
1" - 1 1/2"
2" - 3"
4" - 6" Sch 40
8" - 10" Sch 20
12" Sch 30 VE-334
14" - 24" Sch 20 VE-335
26" - 32" 0.438"
34" 0.469"
36" Sch 20
Elbow 90º JO-09
Elbow 45º JO-10
Equal Tee TE-06
Red. Tee TRE-03 1/2" - 1 1/2"
Cross CRUZ-06
Half Coupling ML-03 VE-306
Red. Coupling LRE-02 VE-307
Cap TAM-06
Union UN-05
Coupling L-05
Elbow 90º JO-07
Elbow 45º JO-08
Equal Tee TE-05
Red. Tee TRE-02
Cross CRUZ-05
Half Coupling ML-02 VE-50
Red. Coupling LRE-01 VE-67
Cap TAM-05
Union UN-04
Coupling L-04
Short Nip.
Long Nip.
Red.Nip.C NIPRC-04
Red .Nip.E NIPRE-10
Red.Nip.C NIPRC-04A
Red .Nip.E NIPRE-10A VE-338
S.R.ELL 90º CRC-01 2" - 24" VE-339
S.R.ELL 90º CRL-01 Wall
S.R.ELL 45º CRL-02 thickness
Tee TE-02 according to
Red. Tee TRE-01 pipe
Conc. Red. REDC-01
Ecc. Red. REDE-02
Cap TAM-02
Cross CRUZ-02
Weldolet WOL-01 VE-310
VE-311
FLG-05E 1/2" - 1 1/2" SW (RF)
FLG-05A 1/2" - 24" BLIND (RF)
FLG-04A 2" - 24" WN (RF)
FLG-05C BLIND (RF)
FLG-04C WN (RF)
JPH-07 1/2" - 10" 1/16" (1,6mm)
JPH-08 12" - 36"
JI-01 1/2" - 36"
JE-05 8" - 24"
JE-06 26" - 36"
(Notes 2) 1/2" - 1 1/2"
(Notes 2 and 4) 1/2" - 1 1/2"
(Notes 2) 1/2" - 1 1/2"
(Notes 2 and 4) 1/2" - 1 1/2" 1/2" - 1 1/2" VAG-17
6000
SW
3000
PLAIN
F i t t i n g s a n d
A c c e s s o r i e s
( N o t e s
1
a n d
7 )
1/2" - 4"
2" - 36"
1" - 1 1/2"
1/2" - 3/4"
1/2" - 3/4"
T-05A
Stainless steel AISI 304 with flexible-graphite, with inner ring AISI 304
Stainless steel AISI 304 with flexible-
graphite
6" - 24"
1" - 1 1/2"
1/2" - 3/4"
2" - 10"
BW/PLAIN
26" - 36"
1" - 1 1/2"
ASTM A 105
2" - 4"
ASTM A 1052" - 4"
1" - 1 1/2"
6" - 24"
26" - 36"
Check valve; horizontal piston; class
800; SW; carbon steel.
Globe valve; class 150; FLG; RF; carbon
steel.
Check
1/2" - 1 1/2" VR-56
Gate valve; class 150; FLG; RF; gear;
carbon steel.
Ball valve; class 150; FLG; RF; carbon
steel, PEEK® seat; over 150°C to
220ºC
Gate valve; class 800; SW; carbon steel.
Gate valve; class 150; FLG; RF; carbon
steel.VG-03
VE-309D
VE-309B
Ball valve; fire tested; class 800; SW;
carbon steel, PEEK® seat.
Ball valve; fire tested; class 800; SW;
carbon steel, PEEK® seat.
VE-312
Ball valve; fire tested; class 150; FLG;
RF; gear; carbon steel, PEEK® seat.VE-312A
Ball valve; fire tested; class 150; FLG;
RF; carbon steel, PEEK® seat.
Ball valve; fire tested; class 150; FLG;
RF; gear; carbon steel, PEEK® seat.
VE-337D
Ball valve; fire tested; class 150; FLG;
RF; carbon steel; RPTFE® seat.
VE-340
Ball valve; fire tested; class 150; FLG;
RF; gear; carbon steel; RPTFE® seat;
2" - 4"
1/2" - 3/4"
Gate (Note 5)
14" - 24"Gate valve; class 150; FLG; RF; gear;
carbon steel.
VG-45
VG-04
Ball valve; fire tested; class 800; SW;
carbon steel; RPTFE® seat.
1/2" - 3/4"
T-02A
Sch 80
T-05A PLAIN
1" - 1 1/2"
API 5L Gr B PSL 1
seamless
CODE Service
TECHNICAL SPECIFICATIONDR-ENGP-1.1
E&P 17 of 134
TECHNICAL SPECIFICATION ET-200.03
PIPING STANDARD AND MATERIAL FOR OIL PRODUCTION AND PROCESS FACILITIES
Ball valve; class 150; FLG; RF; gear;
carbon steel, PEEK® seat; over 150°C
to 220ºC
VE-308
ASME B31.3
DFC-Closed Drain (Corrosive Hydrocarbon); PC-Process (Corrosive Hydrocarbon) (Note
6 and 10); PCW-Produced water (Note 6); DA-Open Drain (Notes 9, 12 and 15); AM-
Amine (Note 14); SP-Vent and tank sounding; F-Safety system and Flare
Pipes and Fittings
MaterialItem
Pipe
T-02B
2" - 4"
0,175" (4,4mm)
1/8" (3,2mm)Fenolic resin with neoprene
Valves (Notes 9 and 13)
Ball (Note 4)
Description
VE-340A
Ball valve; fire tested; class 800; SW;
carbon steel; RPTFE® seat.VE-337B
Ball valve; fire tested; class 150; FLG;
RF; gear; carbon steel; RPTFE® seat;
VR-35ARF
Compressed non-asbestos (aram