dsx-1 performance-series rear cross- connect panels for ... · dsx-1 performance-series rear...

DSX-1 Performance-Series Rear Cross-Connect Panels for Connectorized NE CircuitsInstallation Guide

Model 010-2164-0010 (64 Circuits)

Model 010-2184-0010 (84 Circuits)

Page ii

Telect, Inc. • USA +1.509.926.6000 • Mexico +52.33.3836.37.52www.telect.com • © 2010 Telect, Inc., All Rights Reserved, 129510 A0.1

DSX-1 Performance-Series Rear Cross-Connect Panels for Connectorized NE Circuits

Installation Guide 129510 A0.1

Copyright 2010, Telect, Inc., All Rights Reserved

Telect and Connecting the Future are registered trademarks of Telect, Inc.

1730 N Madson St., Liberty Lake, Washington

Telect assumes no liability from the application or use of these products. Neither does Telect convey any license under its patent rights nor the patent rights of others. This document and the products described herein are subject to change without notice.

About Telect

Telect offers complete solutions for physical layer connectivity, power, equipment housing and other network infrastructure equipment. From outside plant and central office to inside the home, Telect draws on more than 25 years of experience to deliver leading edge product and service solutions. Telect is committed to providing superior customer service and is capable of meeting the dynamic demands of customer and industry requirements. This commitment to customer and industry excellence has positioned Telect as a leading connectivity and power solution provider for the global communications industry.

Technical Support

E-mail: [email protected]

Phone: 888-821-4856 or 509-921-6161

DSX-1 Performance-Series Rear Cross-Connect Panels for Connectorized NE CircuitsInstallation Guide

Table of Contents1.1 Overview ................................................................................................................................ 1

1.1.1 Applications ................................................................................................................... 21.1.2 Features ........................................................................................................................ 2

1.2 Specifications.......................................................................................................................... 31.3 Installation .............................................................................................................................. 4

1.3.1 Installing the Panel ........................................................................................................ 51.3.2 Designating 84-Circuit Panels With 1-28A/1-28B/1-28C Nomenclature ....................... 91.3.2 Offset Panel Mounting ................................................................................................ 12

1.4 Schematic Drawing .............................................................................................................. 141.5 Connection Tables ............................................................................................................... 151.6 Accessories .......................................................................................................................... 181.7 Assembly Drawings ............................................................................................................. 20

List of FiguresFigure 1 - DS1 128-Circuit X-Aisle Panel Models ........................................................................ 1Figure 2 - Front of 84-Circuit Panel .............................................................................................. 2Figure 3 - Remove XC Trough ..................................................................................................... 5Figure 4 - Flush Mounting Panel to a 19-in Rack ......................................................................... 5Figure 5 - Installing 19-in. to 23-in. Panel Rack Adapters ............................................................ 5Figure 6 - Flush Mounting Panel to a 23-in Rack ......................................................................... 6Figure 7 - Ground & Power Connections ..................................................................................... 6Figure 8 - Installing NE Cables on a Model 010-2184-0010 ........................................................ 7Figure 9 - Installing Cross-Connects to Left-Rear Corner of Panel ............................................. 8Figure 10 - Applying Circuit Designation Labels .......................................................................... 9Figure 11 - Adding Decals ........................................................................................................... 9Figure 12 - Applying Labels ....................................................................................................... 10Figure 13 - Applying Labels ....................................................................................................... 10Figure 14 - Applying the Two Labels for the Connectors ........................................................... 11Figure 15 - Installing Rings ........................................................................................................ 12Figure 16 - Mounting Extension Brackets to the 19-in. Rack ..................................................... 12Figure 17 - Mounting Flange Adapters ...................................................................................... 13

Page iii


Figure 18 - Positioning the Panel ............................................................................................... 13Figure 19 - Fastening the Panel to the Rack .............................................................................. 14Figure 20 - Connection Table for 64-Circuit Panel ..................................................................... 15Figure 21 - Connection Table for 84-Circuit Panel, Circuits 1-28 & 29-56 ................................. 16Figure 22 - Connection Table for 84-Circuit Panel, Circuits 57-84 ............................................. 17Figure 23 - Dimensions for 64-Circuit Panel .............................................................................. 20Figure 24 - Dimensions for 84-Circuit Panel .............................................................................. 21

Page iv


DSX-1 Performance-Series Rear Cross-Connect Panels for Connectorized NE Circuits Installation Guide1.1 OverviewTelect offers DSX-1 Performance Series Cross-Connect Panels with 56, 64, or 84 circuits featuring wire-wrap cross-connections and either connectorized or wire-wrapped NE cabling. Telect has a Performance Series Panel to fit any CO circuit count, designation, or cable format. Telect’s Performance Series Panels are the functional foundation of concentration lineups requiring either front or rear cross-connect access.

Shown below are Performance Series Rear Cross-Connect Panels with connectorized rear-side NE cabling: both 64- and 84-circuit panels fit either 19- or 23-in. EIA or WECO racks.

Figure 1 - DS1 128-Circuit X-Aisle Panel Models

Model 010-2164-0010 (64 Circuits)

Model 010-2184-0010 (84 Circuits)


Page 1

Models 010-2164-0010 and 010-2184-0010 are white panels accommodating network-element, connectorized cabling and wire-wrap cross-connection, all on the rear. Cross-connect pinfield features T and R (tip and ring) pins and a a tracer lamp (TL) pin for each circuit.

Each of the 64 or 84 circuits contains Bantam-style jacks at the front of the panel for temporary patching during maintenance or redirecting I/O circuit during troubleshooting. Output signals can be monitored at the Bantam monitor port. Jacks are labeled as follows:

• MON is used to monitor and test the output of the network element connected at the rear of the circuit. The tracer lamp blinks at both ends of the cross connection for 30-to-60 seconds and then stays on while the output circuit is being monitored. Monitoring and test-ing is non-intrusive.

• OUT and IN are the outputs and inputs of that network element. Use these Bantam ports for temporary patching. (I/O temporary patching is intrusive.)

Tracer lamps are located above the jack field.

Near the front corners of all panels are pull-out circuit designation cards.

On the rear, the pinfield is used for wire-wrapping cross-connections (XCs). The removable XC trough below the XC pinfield allows for convenient access to NE cabling during initial phases of wiring.

The XC trough guides XC wiring to the rear corners where 4 in. by 4 in. (Nominal outside dimensions. Inside dimension of rings is 3.75 in. x 3.75 in.) routing rings direct circuit wiring up and down the rack.

1.1.1 Applications

High-density CO environments and for DCS interfaces where vertical and horizontal expansion and adaptability are required. Lineups with 64-, and 84-circuit Performance Series Panels offer the highest-density DSX-1 in the industry.

1.1.2 Features

• Highest ever DS1 termination in minimal space (2RU, 1RU = 2 in.) provides 43% increase in DS1 circuit density over 7-in. high legacy products.

• Circuit multiples match industry-standard SONET OC3, 12, 48 and 192 systems.

• Telect's patented Dedicated Digital Jacks is backed by Telect's DSX lifetime warranty.

• Nonintrusive circuit access, testing, patching, and monitoring are available at the highest density connectivity.

• Industry-standard design enables the use of all legacy Bantam patch cords. (See “1.6 Acces-sories” on page 18.)

• Panels provide easy access to rear-side NE cabling and front-side cross-connections.

Figure 2 - Front of 84-Circuit Panel


Page 2

1.2 Specifications

Signal Interface: Specification:

Monitor Level 20dB ± 1.5dB below signal level

Return Loss Equal to or greater than -26 dB of loss @ 772KHz

Insertion Loss -0.5 dB @ 1.576MHz

Crosstalk < -60 dB

Characteristic Impedance Std DS1 @ 100 Ω

Physical (Nominal): Specification:

Width x Height x Depth* 19 x 4 x 8 in. (483 x 102 x 203 mm)

Weight (Installed) 18 - 20 lbs (8 - 9 kg)

Weight (Shipping) 21 - 23 lbs (9.5 - 10.5 kg)

NOTE: Not including rings. See last page for complete dimensions.

Environment: Specification:

Thermal Limits • -55° C to 85°C, nonoperating• -40° C to 65°C, operating

Thermal Shock per MIL-STD-202, methods 107D

Humidity 0% to 95%, noncondensing, operating and nonoperating

Moisture Resistance per MIL-STD-202, method 106E

Salt Spray per MIL-STD-202F, method 101D

Power & Grounding: Specification:

Chassis GND Terminal Studs (With KEPS Nuts) for Single-Hole Compression Lug

8-32 stud. Torque KEPS nut (using 11/32 in. or 9 mm socket) to ~17 in.-lb (~1.92 N•m).

Tracer Lamp LED Draws 8mA @ 56Vdc

Power for Tracer LEDs -48Vdc BATT and RTN. BATT must be fused @ 1.33A (max.)

Power Terminals #6-32 panhead screws for forked or single-hole compres-sion lugs with 24 AWG wiring or larger

Shield Ground Terminal Same as Power Terminals stated above.


Page 3

1.3 Installation

ALERT!ALERT! Only qualified personnel may install and maintain this product. Verify all connec-tions meet requirements specified in local electric codes or operating company guide-lines.

Please read these instructions carefully before beginning the installation. If you need assistance call Technical Support at 888-821-4856 (domestic calls), or 509-921-6161 (Option 2), or email us at [email protected].

Inspect equipment after unpacking and compare it to the packing list.

Immediately report any shipping damage, defects, or missing parts to Telect at 1-800-551-4567. Keep all documentation that comes with your shipment.

Telect is not liable for shipping damage. If the equipment is damaged, notify the carrier and call Telect’s Customer Service Department at 1-800-551-4567 (domestic only) or 1-509-926-6000 for further recourse.

Mechanical Interface: Specification:

Bantam Jack Insertion Force 4.17 lb (1.9 kg) average

Bantam Withdrawal Force 5.21 lb (2.4 kg) average

Bantam Jack Life > 20K insertion/withdrawal cycles

Vibration Per MIL-STD-202F, method 201A

Cross Connect** Wire-wrap pinfield (TL, T OUT, R OUT, T IN, and R IN per circuit)

Network Element I/O† Connectors 64-pin Amphenol-type female connectors (unshielded; three for inputs from & three for outputs to NEs) for right-angle male connectors on T1 cables.

** Max. wiring distance between XC pins is 85 ft for 24 AWG.† Max. distance between NE and Panel is 655 ft for 22 AWG.


Page 4

1.3.1 Installing the Panel

Procedure steps:

1. Before installing the panel, remove the XC wiring trough on the rear of the panel, as shown on the right.

2. For circuit designation 1A-28A/1B-28B/1C-28C (rath-er than 1-84) on 84-Circuit Performance Series Pan-els (Model 010-2184-1010) only, apply the circuit des-ignation decals (supplied), as instructed. See “1.3.2 Designating 84-Circuit Panels With 1-28A/1-28B/1-28C Nomenclature” on page 9, then continue with this procedure.

3. For flush mounting panel to front rack flange, proceed as follows.(For 2-in. off-set mounting on the front rack flange, see “1.3.2 Offset Panel Mounting” on page 12, then continue with this procedure.)

• For a 19-in rack,

a. Use the four #12-24 thread-cut-ting screws (provided, two per side) to install panel to rack. as shown on the right.

b. Torque the #12-24 screws to 35 in.-lb (4.29 N•m).

c. Install the right and left rings at rear corners using the #6-32 flathead screws provided.

• For a 23-in. rack,

a. Use the four #12-24 thread-cut-ting screws (provided, two per side) to install the two 19-in. to 23-in. flange adapters to the panel, as shown.

Figure 5 - Installing 19-in. to 23-in. Panel Rack Adapters

Captive Screws

Figure 3 - Remove XC Trough

Right Corner Ring

Figure 4 - Flush Mounting Panel to a 19-in Rack

Adapter for Mounting19-in. Panels to 23-in. Racks


Page 5

b. Use the four remaining #12-24 thread-cutting screws (two per side) to install the panel with the flange adapters to the rack.

c. Torque the #12-24 screws to 35 in.-lb (4.29 N•m).

d. Install right and left rings at the rear corners using the #6-32 flathead screws provided.

WARNING !

WARNING! Failure to properly ground this equipment can create hazardous conditions to installation personnel and to the equipment.

ALERT!ALERT! Only use components and crimping tools approved by agencies or certifying bodies recognized in your country or region such as Underwriter’s Laboratories (UL), TUV, etc.

4. Grounding is required. Use a listed (approved) crimping tool to attach a listed (approved), single-hole com-pression lug for a #8 stud onto 14 AWG ground wire.

5. Connect the lug using the innermost of the two #8-32 KEPS nuts provided on the chassis ground stud, as shown in Figure 7.

6. Tighten the innermost KEPS nut to ~17 in.-lb (~1.92 N•m).

7. If CO policy requires that shield ground be tied to chassis ground, in-stall a 24 AWG drain wire between the S. GND screw terminal and chassis ground. (On the chassis ground stud secure wire be-tween the two KEPs nuts provided on the chassis ground stud.)

8. Tighten the outermost KEPS nut to ~17 in.-lb (~1.92 N•m).

Right Corner Ring

Figure 6 - Flush Mounting Panel to a 23-in Rack

Ground Wire

Ring or Forked Lugs

Drain Wire ConnectsShield Grounds toChassis Ground

Figure 7 - Ground & Power Connections


Page 6

Telect recommends that shields be grounded at one, but not both, end of NE cabling and patch cords.

9. For powering tracer lamps, prepare -48Vdc BATT and RTN feeds by crimping fork or ring compression lugs, suitable for a #6 screw, onto suitably long 24 AWG (min.) wires.

10. Connect the end prepared in Step 9 to the power terminals shown in the illustration. Dress the opposite end and connect to a power distribution unit output fused at 1.33A (max).

11. Connect NE I/O T1 cables (24 AWG Preferred), each with a right-angle Amphenol-style, 64-pin, male connector, to the input and output connectors on the rear of the panel, as shown in Figure 11.

The cables can be fed from the top down or bottom up.

NOTE: Normally input cables go to the right rear corner, as indicated in the following illustration, and the output cables to the left rear corner. Always follow operating company guidelines.

12. Use a flat-tipped screwdriver to secure the inboard end of the male-female connection.

13. Use cable ties at the outboard ends of the connectors.

14. Use cable ties at either the rear corner anchors or at the rack’s rear flange holes.

Cable Ties

Use Tie-Down Anchor for J5

J5

Figure 8 - Installing NE Cables on a Model 010-2184-0010


Page 7

15. Use lacing or cable ties to secure the cable along the rack’s channel.

16. After finishing NE cabling in a panel, re-attach the XC trough.

If possible, finish installing all panels and NE cabling in a rack before installing cross-connect wiring.

17. Install cross-connects, as shown in the following illustration for an 84-circuit panel.

Consult the tables in Section “1.5 Connection Tables” on page 15 for NE versus cross-con-nect pinout assignments.

18. Fit XC wires into fanning strips below the pinfield and then along the trough.

19. If possible, run half of the wiring to the left-rear corner ring and the other half to the right corner ring.

20. As cross-connects are assigned, record assignments on the circuit designation decals provided. When finished, affix self-adhesive labels to both sides of the two pull-out designation cards.

Figure 9 - Installing Cross-Connects to Left-Rear Corner of Panel

Prevent wiring conjestion in the trough by running XC I/0 wiring for Circuits 1-42 to the right-rear rings and wiring for Circuits 43-84 to the left-rear rings.


Page 8

NOTE: For service or warranty information, please visit telect.com website, or email inquiries to [email protected] and click on the “Support” tab, or phone us at 800-551-4567 (domestic only) or 509-926-6000.

This procedure is complete.

1.3.2 Designating 84-Circuit Panels With 1-28A/1-28B/1-28C Nomenclature

Procedure steps:

1. Find the adhesive-backed circuit designa-tion decals, shown on the right.

2. Carefully peel off the 1A-through-14B label from the FRONT JACK FIELD decal and affix over the 1-through-42 designations above the front jack field, as shown in Fig-ure 12, following.

Similarly, apply the 15B-through-28C label.

64.65.66.67.68.69.70.71.72.73.74.75.76.77.78.79.80.81.82.83.84.63.

62.61.60.59.58.57.56.55.54.53.52.51.50.49.48.47.46.45.44.43.

22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.21.

20.19.18.17.16.15.14.13.12.11.10.9.8.7.6.5.4.3.2.1.

Circuit Designation Decals

Figure 10 - Applying Circuit Designation Labels

1

Jack Field Decal

Pinfield Decals

Connector Decals

Figure 11 - Adding Decals


Page 9

Figure 12 - Applying Labels

3. Open the pinfield doors on the front of the panel and apply the 1A-through-14B pinfield label over the 1-42 designations behind the left door. Similarly, apply the 15B-through-28C desig-nation over the 43-84 designation behind the right door.

Figure 13 - Applying Labels


Page 10

4. On the back of the panel, apply the two labels for the connectors

Figure 14 - Applying the Two Labels for the Connectors


3


Page 11

1.3.2 Offset Panel Mounting

Telect manufactures brackets to extend the panel 2 inches beyond the rack flange. (See “1.6 Accessories” on page 18.) To install the extension brackets and the panel, proceed as follows.

Procedure steps:

1. Install right and left rings at the rear corners of the panel using the #6-32 flathead screws pro-vided, as shown below.

Figure 15 - Installing Rings

2. Use #12-24 thread-forming screws (provided) to mount extension brackets to the front rack flanges, as follows:

• For a 19-in. rack, mount extension brackets as shown below.

Figure 16 - Mounting Extension Brackets to the 19-in. Rack

Right Ring Assy

Left Ring Assy

Offset Brackets for ExtendingPanel 2 in. Beyond the Rack Flange.*

* Right and left offset brackets areidentical. Fastening hardware is included.


Page 12

• For a 23-in. bracket, fasten two 19-in. to 23-in. flange adapters between extension brack-ets and rack flange, as shown.

Figure 17 - Mounting Flange Adapters

3. Using two people, one at the front of the rack (with the four remaining #12-24 Phillips head thread-cutting screws and fastening tool) and one at the rear of the rack, tilt the panel and pass it through the rack, as shown below.

Figure 18 - Positioning the Panel

Offset Brackets for ExtendingPanel 2 in. Beyond the Rack Flange.*

* Right and left offset and adapter bracketsare identical. Fastening hardware is included withall brackets.

19-in. to 23-in. Adapter Brackets*


Page 13

4. Fasten the panel to the rack. Tighten all #12-24 threading-cutting screws to 35 in.-lb (4.29 N•m).

Figure 19 - Fastening the Panel to the Rack


1.4 Schematic Drawing

S.GND

BATT

RTN

C.GND

R2

RTR

TR

TOUT

IN

IN

OUT

R1

MON

LED ASSEMBLY

RTTL

TL

OUT

INRTRT

TR

RTTL

S.GND

BATT

RTN

C.GND

R1

R2

TL

LED ASSEMBLY

IN

OUT

MON

INOUTOUT

IN

I

Network Element 1 Network Element 2 R1 & R2 = 475 OHM

REAR EQUIPMENT INPUT/OUTPUT

REAR CROSS-CONNECT

O O I


Page 14

1.5 Connection Tables

Figure 20 - Connection Table for 64-Circuit Panel

PinsW/WCircuit

1OUT T

RTR

IN

J3-33J3-1

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

J1-1J1-33

32

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

CircuitJ1/J3Pins Pins

J1/J3

J1-49J1-17

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

J3-17J3-49

INRTRTOUT

W/WPins

J3-34J3-2J1-34J1-2

J3-50J3-18J1-50J1-18

J3-35J3-3J1-35J1-3

J3-51J3-19J1-51J1-19

J3-36J3-4J1-36J1-4

J3-52J3-20J1-52J1-20

J3-37J3-5J1-37J1-5

J3-53J3-21J1-53J1-21

J3-38J3-6J1-38J1-6

J3-54J3-22J1-54J1-22

J3-39J3-7J1-39J1-7

J3-55J3-23J1-55J1-23

J3-40J3-8J1-40J1-8

J3-56J3-24J1-56J1-24

J3-41J3-9J1-41J1-9

J3-57J3-25J1-57J1-25

J3-42J3-10J1-42J1-10

J3-58J3-26J1-58J1-26

J3-43J3-11J1-43J1-11

J3-59J3-27J1-59J1-27

J3-44J3-12J1-44J1-12

J3-60J3-28J1-60J1-28

J3-45J3-13J1-45J1-13

J3-61J3-29J1-61J1-29

J3-46J3-14J1-46J1-14

J3-62J3-30J1-62J1-30

J3-47J3-15J1-47J1-15

J3-63J3-31J1-63J1-31

J3-48J3-16J1-48J1-16

J3-64J3-32J1-64J1-32 J2-16

J2-48J4-16J4-48J2-15J2-47J4-15J4-47J2-14J2-46J4-14J4-46J2-13J2-45J4-13J4-45J2-12J2-44J4-12J4-44J2-11J2-43J4-11J4-43J2-10J2-42J4-10J4-42J2-9J2-41J4-9J4-41J2-8J2-40J4-8J4-40J2-7J2-39J4-7J4-39J2-6J2-38J4-6J4-38J2-5J2-37J4-5J4-37J2-4J2-36J4-4J4-36J2-3J2-35J4-3J4-35J2-2J2-34J4-2J4-34

PinsW/W

OUT TRTR

IN

J4-49J4-17

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

J2-17J2-49

J2/J4PinsPins

J2/J4 Circuit

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

J2-33J2-1

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

J4-1J4-33

INRTRTOUT

33

Circuit W/WPins

J2-32J2-64J4-32J4-64J2-31J2-63J4-31J4-63J2-30J2-62J4-30J4-62J2-29J2-61J4-29J4-61J2-28J2-60J4-28J4-60J2-27J2-59J4-27J4-59J2-26J2-58J4-26J4-58J2-25J2-57J4-25J4-57J2-24J2-56J4-24J4-56J2-23J2-55J4-23J4-55J2-22J2-54J4-22J4-54J2-21J2-53J4-21J4-53J2-20J2-52J4-20J4-52J2-19J2-51J4-19J4-51J2-18J2-50J4-18J4-50


Page 15

Figure 21 - Connection Table for 84-Circuit Panel, Circuits 1-28 & 29-56

PinsW/WCircuit

1 OUT TRTR

IN

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT2

3

4

5

6

7

8

9

10

11

12

13

14

15

16J1-1J1-33

32

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

CircuitJ1/J4Pins Pins

J1/J4

J1-49J1-17

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT RTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

INRTRTOUT

W/WPins

J1-34J1-2

J1-50J1-18

J1-35J1-3

J1-51J1-19

J1-36J1-4

J1-52J1-20

J1-37J1-5

J1-53J1-21

J1-38J1-6

J1-54J1-22

J1-39J1-7

J1-55J1-23

J1-40J1-8

J1-56J1-24

J1-41J1-9

J1-57J1-25

J1-42J1-10

J1-58J1-26

J1-43J1-11

J1-59J1-27

J1-44J1-12

J1-60J1-28

J1-45J1-13

J1-46J1-14

J1-47J1-15

J1-48J1-16 J2-16

J2-48J4-16J4-48

J2-15J2-47

J4-15J4-47

J2-14J2-46

J4-14J4-46

J2-13J2-45

J4-13J4-45

J2-12J2-44

J4-12J4-44

J2-11J2-43

J4-11J4-43

J2-10J2-42

J4-10J4-42

J2-9J2-41

J4-9J4-41

J2-8J2-40

J4-8J4-40

J2-7J2-39

J4-7J4-39

J2-6J2-38

J4-6J4-38

J2-5J2-37

J4-5J4-37

J2-4J2-36

J4-4J4-36

J2-3J2-35

J4-3J4-35

J2-2J2-34

J4-2J4-34

PinsW/W

OUT TRTR

IN

J4-49J4-17

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

J2-17J2-49

J2/J5PinsPins

J2/J5 Circuit

49

50

51

52

53

54

55

56

J2-33J2-1

48

47

46

45

44

43

42

41

40

39

38

37

36

35

34 OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

J4-1J4-33

INRTRTOUT33

Circuit W/WPins

J2-24J2-56

J4-24J4-56

J2-23J2-55

J4-23J4-55

J2-22J2-54

J4-22J4-54

J2-21J2-53

J4-21J4-53

J2-20J2-52

J4-20J4-52

J2-19J2-51

J4-19J4-51

J2-18J2-50

J4-18J4-50

T

J4-57J4-25

J2-57J2-25

J4-58J4-26

J2-58J2-26

J4-59J4-27

J2-59J2-27

J4-60J4-28

J2-60J2-28

J5-1J5-33

J5-34J5-2

J5-35J5-3

J5-36J5-4

J5-37J5-5

J5-38J5-6

J5-39J5-7

J5-40J5-8

J5-41J5-9

J5-42J5-10

J5-43J5-11

J5-44J5-12

J5-45J5-13

J5-46J5-14 J5-28

J5-60

J5-27J5-59

J5-26J5-58

J5-25J5-57

J5-50J5-18

J5-51J5-19

J5-52J5-20

J5-53J5-21

J5-54J5-22

J5-55J5-23

J5-56J5-24

J5-49J5-17

J5-47J5-15

J5-48J5-16

(1A)

(2A)

(3A)

(4A)

(5A)

(6A)

(7A)

(8A)

(9A)

(10A)

(11A)

(12A)

(13A)

(14A)

(15A)

(16A)

(4B)

(3B

(2B)

(1B)

(28A)

(27A)

(26A)

(25A)

(24A)

(23A)

(22A)

(21A)

(20A)

(19A)

(18A)

(17A)

(21B)

(22B)

(23B)

(24B)

(25B)

(26B)

(27B)

(28B)

(20B)

(19B)

(18B)

(17B)

(16B)

(15B)

(14B)

(13B)

(12B)

(11B)

(10B)

(9B)

(8B)

(7B)

(6B)

(5B)


Page 16

Figure 22 - Connection Table for 84-Circuit Panel, Circuits 57-84

J6-16J6-48

J3-16J3-48

J6-15J6-47

J3-15J3-47

J6-14J6-46

J3-14J3-46

J6-13J6-45

J3-13J3-45

J6-28J6-60

J3-28J3-60

J6-12J6-44

J3-12J3-44

J6-27J6-59

J3-27J3-59

J6-11J6-43

J3-11J3-43

J6-26J6-58

J3-26J3-58

J6-10J6-42

J3-10J3-42

J6-25J6-57

J3-25J3-57

J6-9J6-41

J3-9J3-41

J6-24J6-56

J3-24J3-56

J6-8J6-40

J3-8J3-40

J6-23J6-55

J3-23J3-55

J6-7J6-39

J3-7J3-39

J6-22J6-54

J3-22J3-54

J6-6J6-38

J3-6J3-38

J6-21J6-53

J3-21J3-53

J6-5J6-37

J3-5J3-37

J6-20J6-52

J3-20J3-52

J6-4J6-36

J3-4J3-36

J6-19J6-51

J3-19J3-51

J6-3J6-35

J3-3J3-35

J6-18J6-50

J3-18J3-50

J6-2J6-34

J3-2J3-34

PinsW/W

OUT TRTR

IN J3-49J3-17

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

INRTRTOUT

J6-17J6-49

J3/J6PinsPins

J3/J6 Circuit

73

74

75

76

77

78

79

80

81

82

83

84

J6-33J6-1

72

71

70

69

68

67

66

65

64

63

62

61

60

59

58 OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

OUT TRTR

IN

J3-1J3-33IN

RTRTOUT57

Circuit W/WPins

(17C)

(18C)

(19C)

(20C)

(21C)

(22C)

(23C)

(24C)

(25C)

(26C)

(27C)

(28C)

(16C)

(15C)

(14C)

(13C)

(12C)

(11C)

(10C)

(9C)

(8C)

(7C)

(6C)

(5C)

(4C)

(3C)

(2C)

(1C)


Page 17

1.6 Accessories

Description Catalog No. Illustration

64-Pin, 28 Twisted Pair, Shield-ed, T1 Interface Cable with Single 90°, Hooded Male Connector for an 84 -Cir-cuit Panel

22 AWG

24 AWGa

26 AWG

928-1104-0001-xxx

928-2104-0001-xxx

928-3104-0001-xxx

where xxx is the length in ft.

See telect.com for T1 cables with connectors on both ends.

64-Pin, 32 Twisted Pair, Shield-ed, T1 Interface Cable with Single 90°, Hooded Male Connector for a 64-Circuit Panel

22 AWG

24 AWG1

26 AWG

932-1104-0001-xxx

932-2104-0001-xxx

932-3104-0001-xxx


Bantam Patch Cord, Single Plug 040-1000-xxx


Bantam Patch Cord, Dual Plug

040-2000-xxx


Bantam Circuit Guards

Circuit Guard, BLK

Circuit Guard, RED

101222-2

101222-3

Offset Bracket Kit(2 in. offset; white) 999-0041-105

XXX FEET

XXX FEET


Page 18

Designation Decals:b

For a 64-Circuit Panel

127603

(Designations 1A-28A, 1B-28B, & 1C-28C)

128085

a. The 24 AWG wire is the best choice.b. Designation decals are included with panel. Use these catalog numbers to order replacements.

Description Catalog No. Illustration

1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16. 48.

47.46.45.44.43.42.41.40.39.38.37.36.35.34.33.

32.31.30.29.28.27.26.25.24.23.22.21.20.19.18.17. 49.

50.51.52.53.54.55.56.57.58.59.60.61.62.63.64.

8C.9C.10C.11C.12C.13C.14C.15C.16C.17C.18C.19C.20C.21C.22C.23C.24C.25C.26C.27C.28C7C

6C.5C.4C.3C.2C.1C.28B.27B.26B.25B.24B.23B.22B.21B.20B.19B.18B.17B.16B.15B.

22A.23A.24A.25A.26A.27A.28A.1B.2B.3B.4B.5B.6B.7B.8B.9B.10B.11B.12B.13B.14B.21A.

20A.19A.18A.17A.16A.15A.14A.13A.12A.11A.10A.9A.8A.7A.6A.5A.4A.3A.2A.1A.


Page 19

1.7 Assembly Drawings

Figure 23 - Dimensions for 64-Circuit Panel

MON

OUT

OUT

MON

IN

IN

MON

OUT

IN

4844403633

24

OUT

IN

MON

201612841

TL

RTR

T T

RTR

TL

www.telect.com

NOTE: Dimensions are in in. (mm)

REAR VIEW

FRONT VIEW

TOP VIEW

(ROTATED, SHOWN WITH XC WIRING TROUGH REMOVED)

1.00 (25.4)

1.00 (25.4)

2.25(57.2)

2.25(57.2)3.97

(100.8)

25.23 (640.9)

9.98(253.6)

3.75 (95.2)

12.01(305.2)

3.75(95.2)

0.50 (12.7)

19.00 (482.6)

18.31 (465.1)

28 32

52 56 60 64

TL

TLTL

TL

www.telect.com

OUT

IN

OUT

IN

6452 56 6048322824201612841 40 4436

~4.0(~100)

Circuit Designation Card Tab(Card Shown Fully Retracted)

Circuit Designation Card(Card Shown Fully Extended)

0.5 (12.7)#8-32 Stud & KEPS Nuts #6-32 Panhead Screws0.27 (6.6)

J1 IN 1-32

J2 IN 33-64

J3 OUT 1-32

J4 OUT 33-64

RTN

BATT

0.6A

-48V

S.G

ND

1

Pin 1

Pin 1

64-Pin Female Amphenol-Style Connectors (4)

1

1

1


Page 20

Figure 24 - Dimensions for 84-Circuit Panel

MON

OUT

OUT

MON

IN

IN

MON

OUT

IN

84827874666258504643

42403632

OUT

IN

MON

242012841

TL

RTR

IN

OUTT

848065 70 7550 55 60454035302520151051

TOUT

INRTR

TL

www.telect.com

NOTE: Dimensions are in in. (mm)

REAR VIEW

FRONT VIEW

TOP VIEW

(ROTATED, SHOWN WITH XC WIRING TROUGH REMOVED)

1.00 (25.4)

1.00 (25.4)

2.25(57.2)

2.25(57.2)3.97

(100.8)

25.25 (641.4)

9.98(253.6)

3.75 (95.2)

12.01(305.2)

3.75(95.2)

0.50 (12.7)

19.00 (482.6)

18.31 (465.1)

~4.0(~100)

Circuit Designation Card(Card Shown Fully Extended)

Circuit Designation Card Tab(Card Shown Fully Retracted)

#6 Panhead Screws#8-32 Stud & KEPS Nuts

0.26(6.6)

RTN

BA

TT

0.7A

-48V

S.G

ND

J1 IN 1-28

J3 IN 57-84

J2 IN 29-56J4 OUT 1-28

J6 OUT 57-84

J5 OUT 29-56

16 28

7054

0.5 (12.7)

1

Pin 1

Pin 1

64-Pin Female Amphenol-Style Connectors (4)

1

1

1

1


Page 21

This page intentionally left blank.


Page 22

dsx-1 performance-series rear cross- connect panels for ... · dsx-1 performance-series rear...

Documents