EC centrifugal fans backward curved, Ø 560

Highlights: – 9-blade fan, 3-phase fan motor – 10 VDC max. output / 10 mA, 20 VDC max. output / 50 mA, 0-10 V slave output, 24 V external program input, 0-10 VDC / PWM control input, 0-10 V or 4-20 mA sensor input, external release input– Integrated PID controller, control interface with SELV potential safely disconnected from the mains, RS485 MODBUS RTU technology – Over-temperature protected electronics / motor, operation and alarm display, alarm relay – Soft start, PFC passive, line undervoltage / phase failure detectionMaterial: Impeller: Aluminum sheet Rotor: Coated in black Electronic housing: Die-cast aluminumMounting position: Shaft horizontal or rotor on bottom; rotor on top on request Condensate discharge holes: Rotor-side Direction of rotation: Clockwise, seen on rotor

(1) Nominal data at maximum load.

Measurement: LU-118570 Measurement: LU-120955 Measurement: LU-120956 Measurement: LU-120957

Air performance measured as per: ISO 5801, Installation category A, without protection against accidental contact. Suction-side noise levels: LWA as per ISO 13347, LPA measured at 1m distance to fan axis. The values given are valid under the measuring conditions mentioned and may vary accoring to the actual installation situation. With any deviation to the standard set-up, the specific values have to be checked and reviewed once installed or fitted.

For detailed information on the measuring set-up, please contact ebm-papst.

Curvesn

rpm

Pe

W

I A

(460V)

I A

(230V)

LwA

dB(A)

Nominal Data Nom

inal

vol

tage

rang

e

Freq

uenc

y

Pow

er in

put (

1)

Spee

d (1

)

Curr

ent d

raw

(1)

Tem

pera

ture

rang

e (1

)

Mas

s

I ngr

ess

prot

ectio

n ra

ting

Elec

trica

l wiri

ng d

iagr

am

UL A

ppro

val

Type K Module Motor VAC Hz Watts RPM A °C lbs

R3G560-AH29-66F EG1R-240-560-30 M3G150-IF 200...240 50/60 3,100 1,510 9.2 -25...60 65 IP54 A Yes

R3G560-AH23-65F EG1R-480-560-30 M3G150-IF 380...480 50/60 3,100 1,510 4.6 -25...60 65 IP54 A Yes

0 2.000 4.000 6.000 8.000 cfm

0

0.2

0.

4

0.6

0.8

1

1

.2

1.4

1

.6

1

.8

2

2

.2

2.4

2.6

2

.8

3

3.2

3

.4

3.6

3.8

in

. wg

2.000 4.000 6.000 8.000 10.000 12.000 14.000 16.000 m3/h

pfs[Pa]

pfs[Pa]

2.000 4.000 6.000 8.000 10.000 12.000 14.000 m3/h

950

900

850

800

750

700

650

600

550

500

450

400

350

300

250

200

150

100

50

pfs[Pa]

1

2

3

4

5

6

7

8

9

10

11

12A

A

A

A

A

A

A

A

A

A

A

A

13

14

15

16A

A

A

A

1

2

3

4

5

6

7

8

9

10

11

12A

A

A

A

A

A

A

A

A

A

A

A

13

14

15

16A

A

A

A

1520 2029 3.1 6.2 87

1520 2636 4.0 8.0 84

1520 3000 4.6 9.2 82

1520 2981 4.6 9.2 83

1260 1156 1.8 3.6 81

1260 1519 2.3 4.6 79

1260 1730 2.7 5.4 78

1260 1619 2.5 5.0 78

1000 617 1.0 2.0 75

1000 799 1.3 2.6 73

1000 908 1.4 2.8 72

1000 839 1.3 2.6 73

760 302 0.6 1.2 68

760 378 0.7 1.4 69

760 423 0.7 1.4 67

760 392 0.7 1.4 67

EG1R-XXX-560-30Ø2

2.24

( 565

)Ø1

5.67

( 398

+ 1.5

)

Depth of screw max. 25mm

Cable diameter: min. 4 mm, max. 10 mm; tightening torque: 4+0.6 Nm

Accessory part: Inlet nozzle 63071-2-4013not included in the standardscope of delivery.

Tightening torque 3.5+0.5 Nm

Ø9.13 (232 -2)

Ø10.83 (275)Ø9.92 (252 +0.3)

7.68 (195)

10.16 (258)

.20 (5)

10.79 (274+2)13.54 (344 +3)

2.76 (70)3.23 (82)

.08 (2)

Ø15.

16 ( 3

85)

Ø14.

96 ( 3

80)

Ø20.

28 ( 5

15)

Ø19.

29 ( 4

90)

R3G560-AHXX-XXF

347.35(13.675)

22.0

47 ( 5

60)

29.528 (750)Ø .433 (11)8 PLACES 302.35 (11.603)

31.4

96 ( 8

00)