edge 160 mitring guide - stratco · 2020. 1. 6. · edge 160 corner assembly step 1 lengths of...
TRANSCRIPT
![Page 1: EDGE 160 MITRING GUIDE - Stratco · 2020. 1. 6. · EDGE 160 CORNER ASSEMBLY STEP 1 Lengths of pre-mitred gutter to be fit in-place either under patio roofing overhang, or into fascia](https://reader035.vdocument.in/reader035/viewer/2022071608/614635868f9ff81254201e09/html5/thumbnails/1.jpg)
Safety Glasses
Ø3.2mm Drill Bit
Gloves
Rivet Gun
Marker
Rivets
Tin Snips
Silicone Gun
Drill
Silicon
GUTTER MITRING GUIDE
STRATCO EDGE 160 GUTTER
INSTALLATION GUIDE
EDGE 160 MITRING GUIDEThis document provides templates and instructions to assist in mitring Stratco Edge 160 Gutter for 90° corners.The internal & external templates provided within this document can act as a guide to generate the 45° mitred cuts required for joining gutters at 90°.It must be noted that the dimensions of the gutters provided may vary slightly from the templates. It is always best practice to measure-out a 45° mitre rather than relying on templates.NOTE: Ensure templates are printed at 1:1 (A3 single page spread preferred).
TOOLS REQUIRED
![Page 2: EDGE 160 MITRING GUIDE - Stratco · 2020. 1. 6. · EDGE 160 CORNER ASSEMBLY STEP 1 Lengths of pre-mitred gutter to be fit in-place either under patio roofing overhang, or into fascia](https://reader035.vdocument.in/reader035/viewer/2022071608/614635868f9ff81254201e09/html5/thumbnails/2.jpg)
BROCG
NI
« SCAN THIS QR CODE TO FIND A STRATCO NEAR YOU
1300 155 155stratco.com.auAll brands and logos/images accompanied by ® or ™ are trade marks of Stratco (Australia) Pty Limited. ® Copyright December 2019
ø3.2mm COLOUR RIVETS
90°
EXTERNAL MITRE
INTERNAL MITRE
90°
EXTERNAL MITRE COVER
INTERNAL MITRECOVER
EDGE 160 CORNER ASSEMBLY
STEP 1
Lengths of pre-mitred gutter to be fit in-place either under patio roofing overhang, or into fascia clips.
STEP 2
Gutter faces must be aligned.A small gap is permitted between mitred edges.
STEP 3
External & Internal gutter mitre covers will be supplied to cover each corner. Fit each mitre cover in-place from beneath the gutter.
STEP 4
Drill four ø3.2mm holes in the gutter using the pilot holes in the mitre covers as a guide.Rivet the mitre covers to the gutters using colour-matched ø3.2mm rivets.Seal each corner using silicone within the gutter.
![Page 3: EDGE 160 MITRING GUIDE - Stratco · 2020. 1. 6. · EDGE 160 CORNER ASSEMBLY STEP 1 Lengths of pre-mitred gutter to be fit in-place either under patio roofing overhang, or into fascia](https://reader035.vdocument.in/reader035/viewer/2022071608/614635868f9ff81254201e09/html5/thumbnails/3.jpg)
EDGE 160 GUTTER MITRING GUIDE
GUTT
ER F
RONT
45° 45°
45°
55°
35°
135°
190°
0mm50 60 70 80 9040302010
100mm
FOLD
FOLD
FOLD
FOLD
FOLD
FOLD
20mm 58mm 80mm 110mm 24mm
EDGE 160 EXTERNAL MITRE FLAT PATTERN TEMPLATECUT-OUT TEMPLATE FOR MARKING-UP GUTTERS
FLIP TEMPLATE FOR LEFT & RIGHT VARIATIONS
ENSURE TEMPLATES ARE PRINTED AT “ACTUAL SIZE”
EXTERNAL PAGE 1
![Page 4: EDGE 160 MITRING GUIDE - Stratco · 2020. 1. 6. · EDGE 160 CORNER ASSEMBLY STEP 1 Lengths of pre-mitred gutter to be fit in-place either under patio roofing overhang, or into fascia](https://reader035.vdocument.in/reader035/viewer/2022071608/614635868f9ff81254201e09/html5/thumbnails/4.jpg)
GUTT
ER F
RONT
45° 45°
45°
55°
35°
135°
190°
0mm50 60 70 80 9040302010
100mm
FOLD
FOLD
FOLD
FOLD
FOLD
FOLD
20mm 58mm 80mm 110mm 24mm
EXTERNAL PAGE 2
![Page 5: EDGE 160 MITRING GUIDE - Stratco · 2020. 1. 6. · EDGE 160 CORNER ASSEMBLY STEP 1 Lengths of pre-mitred gutter to be fit in-place either under patio roofing overhang, or into fascia](https://reader035.vdocument.in/reader035/viewer/2022071608/614635868f9ff81254201e09/html5/thumbnails/5.jpg)
EDGE 160 GUTTER MITRING GUIDE
GUTT
ER F
RONT
45°
45°
170°
125°
45°
55°
45°
45°0mm
50 60 70 80 9040302010100mm
FOLD
FOLD
FOLD
FOLD
FOLD
FOLD
20mm 58mm 80mm 110mm 24mm
INTERNAL PAGE 1
![Page 6: EDGE 160 MITRING GUIDE - Stratco · 2020. 1. 6. · EDGE 160 CORNER ASSEMBLY STEP 1 Lengths of pre-mitred gutter to be fit in-place either under patio roofing overhang, or into fascia](https://reader035.vdocument.in/reader035/viewer/2022071608/614635868f9ff81254201e09/html5/thumbnails/6.jpg)
EDGE 160 INTERNAL MITRE FLAT PATTERN TEMPLATECUT-OUT TEMPLATE FOR MARKING-UP GUTTERS
FLIP TEMPLATE FOR LEFT & RIGHT VARIATIONS
ENSURE TEMPLATES ARE PRINTED AT “ACTUAL SIZE”
GUTT
ER F
RONT
45°
45°
170°
125°
45°
55°
45°
45°0mm
50 60 70 80 9040302010100mm
FOLD
FOLD
FOLD
FOLD
FOLD
FOLD
20mm 58mm 80mm 110mm 24mm
INTERNAL PAGE 2