eii shw exclusive professional sqr pvt 1199133-a02-d

1199133-A02-D 18/2/20

INSTALLATION INSTRUCTIONS

SHOWER

Engle�eld

EXCLUSIVE SERIES Pivot Doors

Englefield has a historyof making superb showersand their popularity istestament to their qualityand affordability.

It’s the details that Englefieldcares about - from pioneeringthe latest technology, toinnovative design, it’s all tomake your showeringexperience the very best itcan be.

Note: Tapware and accessories are not included. Handles may di�er from those pictured.

Before installing the shower please read these instructions carefully to familiariseyourself with the required tools, materials and installation sequences. Please leave theseinstructions for the consumer after installation. Refer to the separate care and maintenanceguide for important care and cleaning information.

Ensure that the shower tray and wall, if applicable, are completely finished prior toinstalling your shower door and return. Follow all warnings, cautions and instructionscontained in this guide.

1. ENGLEFIELD strongly recommends that a minimum of TWO persons install this enclosure due to the weight of the door panels. 2. Toughened safety glass cannot be cut. Risk of injury or product damage.

3. Wear protective footwear when lifting panels.

4. Wear safety glasses when drilling.

1. The wall retainers must be installed onto a waterproof, vertical and flat wall surface. Failure to do so will result in an unsatisfactory seal, which may cause property damage. The wall inclination (out of squareness) is recommended to be out by no more than +/- 4mm/m. 2. Please install this door onto an ENGLEFIELD Quick - Fit shower tray only, unless installing directly onto tiled walls and floor.

®

3. Care must be taken when drilling into walls and floors to avoid any hidden pipes or

wires.

4. It is the responsibility of the INSTALLER to ensure that the installation complies with council and or local authority bylaws.

INSTALLATION INSTRUCTIONSPivot Doors

BEFORE YOU BEGIN

SAFETY !

! ATTENTION

ENGLEFIELD

Instructions, drawings, and diagrams contained in this manual present information available at the time of printing. Although every attempt has been made to keep them up-to-date, Engle�eld reserves the right to implement product changes without further notice.

EXCLUSIVE SERIES

Wall Framing for acrylic tray with acrylic wall

Page 2


ENGLEFIELD

1a - CONSTRUCTION REQUIREMENTS [corner enclosure - pivot door with side panel]

Due to the weight of the shower system Englefield strongly recommendsconstructing double studs (as below) to fix the wall retainers to.

This section is for a corner enclosure [pivot door with side panel].For alcove [door only] installations see section 2 (page 8).

!

ATTENTION

TOOLS AND MATERIALS REQUIRED

3.0 mm 6.0 mm2.5 mmPhillips

A

Double studs

Double studs

B

Size

For Acrylic tray/base

Dim ‘A’

900 x 900

NOTE: Based on the use of standard 10mm wall board

900

1000 x 1000 1000

Dim ‘B’

900

1000


1b - PARTS IDENTIFICATION [corner enclosure - pivot door with side panel]

Page 3


ENGLEFIELD

EXCLUSIVE SERIES

Return SideWall Channel (Retainer)

Return Panel

Corner Post

Door Assembly

Door SideWall Channel (Retainer)

Pivot Doors

1c - INSTALLATION [corner enclosure - pivot door with side panel]

Page 4


ENGLEFIELD

EXCLUSIVE SERIES

Check the distance between the walls to ensure that the Door and

Return are within the maximum and minimum enclosure tolerances.

1

It is recommended that thewaste outlet be ‘taped over’ toavoid the loss of any componentsduring installation.

2

Shower base MUST be installedlevel.3

Select preferred shower dooropening and Return position.4

Poagainst shower walls, restingon the shower base sill.Door wall retainer must have

inside of the shower.

5

DOOR SIDE RETURN SIDE

10 mm

10 mm

10mm from the front edge of theshower base.Check vertical with spirit level and

ENSURE WALL RETAINER PROFILESARE PLUMB.NOTE: DISCARD FROM DOOR PACK 1 X DOOR WALL RETAINER PROFILEAS THIS IS NOT REQUIRED. (Refer to the exploded view onopposite page).

O

DOOR SIDE

RETURN SIDE

TYPE DOOR ADJUSTMENT (mm) MIN MAX

900x900

1000x1000

851 889

951 989

TYPE RETURN ADJUSTMENT (mm) MIN MAX

900x900

1000x1000

858 879

964 985

A

B

Pivot Doors


ENGLEFIELD

EXCLUSIVE SERIES

Centralise Door Assemblybetween Wall Retainer and Corner Post.

Position Return Panel betweenWall Retainer and Corner Post sothat the black lines at each cornerare not visible. DO NOT push thePVC gasket into position at thisstage.

Mark corner of shower base10mm in from front edges.6

Fix both wall retainers in place using the 6 long screws. Make

sure the screws go into studs.7

Panel Assembly and push intoposition.9

Move 90° Corner Post andReturn Panel Assembly out10

Fit Door Assembly into Wall

to Door Assembly.

11

predetermined corner position.12

13a

b

Note: If Screwing into backing board only, use appropriate wallanchors in the wall.

CAUTION: BEFORE DRILLING HOLES, ENSURE THERE ARE NO ELECTRICAL CABLES OR WATER

PIPES BEHIND WALLS

Caution:wall retainers by screwing through the backing board and into studs. Other methods may cause warping and might void warranty.

Insert return panel into wallretainer so that the black

mark aligns with the edge of the . .reniater llaw

8

DO NOT push the PVC gasket into position at this stage.

Pivot Doors


ENGLEFIELD


Using spirit level, plumb Door andReturn assembly and Corner Post.Tape into position as shown(tape not supplied). Check Dooropens and shuts properly and theblack lines on the Return assemblytop and bottom rails remainhidden. Readjust if necessary.

Check that the Door and ReturnPanel Assemblies are level withtop of Wall Retainer and 90°

14

Fit top and bottom hinge caps. (Note bottom cap has ‘wings’).

15

Slide drip edge seal over wing on bottom hinge cover and trim

door glass.

16

Pbeside door edge extrusion

enough to slip drip seal moulding underneath. (NB: drip seal mouldingand retainer bracket are ‘handed’.)

and pull into contact with door edge extrusion. Clamp in place using thebracket and No. 6 screw.

18

Fit handles following instructions supplied withhandle.

19

20

NOTE: This is an important partof the installation procedure and your careful attention at this stage will ensure that you will obtain the best possible results.

DO NOT PROCEED TO STEP 21 UNTIL DOOR IS OPERATING CORRECTLY.

IMPORTANTTEST THE OPENING AND CLOSINGOPERATION OF THE PIVOT DOOR

If door alignment is incorrect, doorwill not fuction properly and furtheradjustments are necessary.Remove tape and re-align untilcorrect alignment is achieved.

17

Ensure that the end of this seal just clears the Door Jamb as the door closes to create the best seal.

Fit the other small screw to the top hole in the door edge extrusion.


ENGLEFIELD

EXCLUSIVE SERIES

Drill holes (with 2.5mm drill bit, DO NOT USE A BIGGER

DRILL BIT) through punched holes at top and bottom of each Wall Retainer and Corner Post to secure door and return. Make sure Door and Return assemblies do not move during this operation. Fit screw, screw caps and remove tape.

Fit long seal to hinge edge of glass. Flap faces into enclosure.

Push down to butt against bottom seal. Trim to top of glass.

23

21 Position Return Panel PVCgasket by pushing outside leginto both Wall Retainer andCorner Post. It should ‘snap’into place. Now push the insideleg into place.

22 Install the handles by followingthe instructions supplied in thehandle carton.

24

RETURN WALL RETAINER

DOOR WALL RETAIN-

90O CORNER POST

Inside Shower

Outside Shower

Push outside leg

Push inside leg

Pivot Doors

Proceed to section 3,sealant application.


ENGLEFIELD


2a - INSTALLATION [alcove enclosure - pivot door only]

Double studs

Double studs

TOOLS AND MATERIALS REQUIRED

3.0 mm 6.0 mm2.5 mmPhillips

A B

2005mmMinimum

Height

This section is for an alcove enclosure [pivot door only].For corner [door + side panel] installations see section 1 (page 2).

Due to the weight of the shower system Englefield strongly recommendsconstructing double studs (as below) to fix the wall retainers to. !

ATTENTION

Wall Framing for acrylic tray with acrylic wall

Size Dim ‘A’900 x 900 9001000 x 1000 1000

Dim ‘B’884

+2-0

984

NOTE: This setup allows for the useof standard 10mm wall board.A thicker wall board could make therecess too narrow for the door system.

2b - PARTS IDENTIFICATION [alcove enclosure - pivot door only]

Page 9


ENGLEFIELD

EXCLUSIVE SERIES

Door Wall Channel(Retainer)

Door Assembly Door Wall Channel(Retainer)

Pivot Doors

2c - INSTALLATION [alcove enclosure - pivot door only]

Page 10


ENGLEFIELD


Check the distance between the walls to ensure they are within

the maximum and minimum enclosure adjustment tolerances.

1 dellatsni eb TSUM esab rewohSlevel.3

It is recommended that the wasteoutlet be ‘taped over’ to avoid the lossof any components during installation.

2

Lift door panel onto the tray and slideit hinge side into the wall retainer.Push it hard against the wall.

6

CAUTION: BEFORE DRILLING HOLES, ENSURE THERE ARE NO ELECTRICAL CABLES OR WATER

PIPES BEHIND WALLS

Fix hinge side wall retainer in place using 3 of the 6 long

screws. Make sure the screws go into studs.

5

wall retainers by screwing through the backing board and into studs. Other methods may cause warping andmight void warranty.

Note: If screwing into backing board only, use appropriate wall anchors in the wall.

10 mm

Select preferred shower dooropening. It is recommended to startthe installation from the hinge sideof the door.

4

against shower wall, resting on the shower

the inside of the shower.

from the front of the shower base. Check

holes.ENSURE WALL RETAINER PROFILE IS PLUMB.

TYPE ADJUSTMENT TOLERANCE (mm) MIN MAX

900 mm

1000 mm

836

936

874

974


ENGLEFIELD


Attach second Wall Retainer P7 Check that the Door Assembly

top edges are level.

10

Fit top and bottom hinge caps.(Note: bottom cap has ‘wings’.)11

position against the wall.8

Centralise Door Assembly9

Slide drip edge seal over wingon bottom hinge cover and

Repeat between hinge cover

glass.

12

door edge extrusion enough to slipdrip seal moulding underneath.(Note: Drip seal moulding andretainer and ‘handed’).

glass and pull into contact withdoor edge extrusion. Clamp inplace using the bracket and No. 6screw.

13

NOTE: DOOR ASSEMBLY MUST BE PLUMB USING A SPIRIT LEVEL.

Ensure the end of this seal just clears the Door Jamb as the door closes to create the best seal.

Fit the other small screw to the top hole in the door edge extrusion.

front of the shower base.Check vertical with spirit level and

remaining long scews. Ensure the screws go into the stud.Fit all 6 screw caps.

10 mm


ENGLEFIELD


Using spirit level plumbDoor Assembly. Tape intoposition as indicated.

14 Fit long seal to hinge edge of glass. Flap faces into

enclosure. Push down to butt against bottom seal. Trim to top of glass.

16

If door alignment is incorrect, doorwill not function properly andfurther adjustments are necessary.Remove tape and re-align untilcorrect alignment is achieved.

DO NOT PROCEED TO STEP 15 UNTILDOOR IS OPERATING CORRECTLY.

NOTE: This is an important part ofthe installation procedure and yourcareful attention at this stage willensure that you will obtain the bestpossible results.

IMPORTANTTEST THE OPENING AND CLOSINGOPERATION OF THE PIVOT DOOR.

Fit handles following instruc-tions supplied with handle.17

Drill holes (use 2.5mm drill bit, DO NOT USE A BIGGER DRILL

BIT) through punched holes at top and bottom of each wall retainer to secure door. Fix screws as pictured.Fit caps & remove positioning tape.

15

Proceed to section 3,sealant application.


ENGLEFIELD

EXCLUSIVE SERIES

the joint between the CornerPost and Door Jamb.

For corner enclosures, seal up to the PVC gasketjoints between Return Panel& Corner Post and Return Panel& Wall Retainer.

SEALANT APPLICATION STEPS

Ensure all joints are clean anddry before applying sealant.

For metallic �nish showers, clear silicone is required.For white �nish showers,white silicone is required.

(b) Hold the tube at 45° angle & push

(c) The surface of the sealant canbe smoothed (before surface dries)

a small quantity of water with one drop of washing liquid added.

(d) Excess sealant should be removed immediately with a damp cloth.

CAUTION: Avoid contact with skin, eyes and mouth and avoid breathing

with water. If irritation persists, seekmedical attention. Keep out of reach of children.

IMPORTANT

SIKASIL NG SEALANT SHOULD BEAPPLIED TO ALL OUTSIDE JOINTS.

DO NOT SEAL FROM INSIDE.

2a. Seal full height of the jointbetween the Walls and theWall Retainers.

INSTALLATION COMPLETE

d.

(a) Cut tip of silicone tube nozzle

at 45O angle.

1.

(e) Allow the silicone 24 hours to cure before using the enclosure.

6mm

45°

For sealant application, follow steps(a) to (e) detailed below.

e.

b. Seal joint between the Door Sill and the Shower Tray.For corner enclosures, sealthe joint between the ReturnPanel and the Shower Tray.

To a height of 100mm, sealjoints between Door Frameand Wall Retainer(s).For corner enclosures, sealjoint between Door Frameand Corner Post.

c. IMPORTANTALLOW 24 HOURS FOR SEALANT AND

ADHESIVE TO CURE BEFORE USING THE SHOWER.

24hrs

For corner enclosures, onmetallic �nish showers seal

3 - SEALANT APPLICATION

Pivot Doors

Spare Part Image Description Codes

Hinge Kit Englefield 1152757- 1 x kit, contains part numbers on this page (marked with )Ø White

Hinge outer - Door hinge Englefield Q6700-W3- 1 x outer hinge White

Englefield Q6700-CP ØChrome

Hinge inner - Door hinge Englefield Q6701-NP Ø- 1 x inner hinge

Pad - Outer - Door hinge Englefield Q670002 Ø- 1 x Outer hinge pad

Pad - Inner - Door hinge Englefield Q670001 Ø- 1 x inner hinge pad

Screw M6x16 - Door hinge Englefield Q912320 Ø- 1 x Hinge screw - M6x16

Pin - Door hinge Englefield Q913000 Ø

- 1 x Hinge pin - 5mm x 30mm

Bush - Door hinge Englefield Q356050 Ø- 1 x hinge bush

Pivot block - Door hinge Englefield Q3800-0 Ø- 1 x hinge pivot block White

Englefield Q3800-GYGrey

Cover set - Door hinge Englefield Q6710-W3 Ø- 1 x bottom hinge cover with wings & 1 x top hinge cover White

Englefield Q6710-CPChrome

Page 14


ENGLEFIELD

EXCLUSIVE SERIES

4 - SPARE PARTS

Pivot Doors


ENGLEFIELD

EXCLUSIVE SERIES

Spare Part Image Description Codes

Frame Block Englefield Q3500-W3- 1 x frame block White


Bracket kit - VQR drip seal retainer Englefield Q9097-W3- 2 x 9mm coated screws, 2 x retainer brackets & White 2 x drip seal mouldings


ProfileMagnetic strip Englefield Q360000- 1 x generic length door magnetic strip

End cap - Magnetic strip Englefield Q3530-W3- 1 x magnetic strip end cap White


Screw cap pack Englefield 1152746- 15 x white screw cap

Glass Aftercare Pack- Limescale Remover Surface Conditioner Applicator Sponge Information Booklet

White

Englefield 98945A-NA

Profile Door jamb - Magnet side- 1 x door jamb - magnet side

Englefield Q1100-T-W3White 1930mm

Englefield Q1100-T-SASilver 1930mm

Englefield Q1100-T-SSSatin 1930mm

Profile

Door jamb - Standard- 1 x door jamb extrusion




Profile Post - 90 degrees (Square Corner Only )- 1 x 90 degree post




Screw kit - Extrusion assembly Englefield Q9090-0- 8 x 33mm screws, 13 x 9mm screws & 13 x screw White caps (for 9mm screws)


Info Booklet

Applicator

ConditionerSurfaceRemover

Limescale

Pivot Doors


ENGLEFIELD

EXCLUSIVE SERIES

Spare Part Image Description CodesRH Top / LH Bottom extrusion - Door ( Rondo Only ) Englefield Q2222-W3RH Top / LH Bottom extrusion - 900 Door Englefield Q2230-W3- 1 x RH top or LH bottom door extrusion White

Reference: Length = 831mm Distance from end to centre of pivot hole = 187mm

LH Top / RH Bottom extrusion - 900 Door Englefield Q2231-W3- 1 x LH top or RH bottom door extrusion White

Reference: Length = 831mm Englefield Q2231-SA Distance from end to centre of pivot hole = 187mm Silver

Englefield Q2231-SSSatin

RH Top / LH Bottom extrusion - 1000 Door Englefield Q2235-W3- 1 x RH top or LH bottom door extrusion White



LH Top / RH Bottom extrusion - 1000 Door Englefield Q2236-W3- 1 x LH top or RH bottom door extrusion White



ProfileSeal - Straight glass - Door bottom Englefield Q371111- 1 x generic length Valencia door bottom straight drip seal

Profile U Seal- 1 x vertical U seal

Englefield Q37105-T-W3

White 1930mm

Englefield Q37105G-T

Grey 1930mm

Wall retainer - Return- 1 x return wall retainer




Profile Wall retainer - Door- 1 x door wall retainer




ProfileSeal - Vertical - Door- 1 x door seal

Englefield Q634050-T1930 shower

Profile

Profile

Profile

Profile

Profile

Englefield Q2230-SASilver


Pivot Doors

Engle�eld


CONTACT AND WARRANTY INFORMATION

NEW ZEALANDKOHLER NZ LTD

- For warranty and other information, please visit our website.

- For contact information, please refer to the Home Owner’s Guide.

Please refer to our website for cleaning instructions.

CLEANING AND MAINTENANCE INSTRUCTIONS

www.englefield.co.nz

AUSTRALIA KOHLER AUSTRALIA

www.englefield.com


eii shw exclusive professional sqr pvt 1199133-a02-d

Documents