elct564 spring 2012
DESCRIPTION
ELCT564 Spring 2012. Diodes, Transistors and Mixers. Diodes. Diodes are non-linear devices. Passive diodes --- signal detection, phase shifting. Non-linear devices. Active FET, MESFET, HBT, BiCMOS -- signal generation and amplification. Rectifying properties of semiconductor materials - PowerPoint PPT PresentationTRANSCRIPT
ELCT564 Spring 2012
04/22/23 1ELCT564
Diodes, Transistors and Mixers
Diodes
04/22/23 ELCT564
• Diodes are non-linear devices
• Non-linear devicesPassive diodes --- signal detection, phase shifting
Active FET, MESFET, HBT, BiCMOS -- signal generationand amplification
• Rectifying properties of semiconductor materials Known since 1874 --- created by the establishment of electrostatic barrier inthe path of the current flow
• Electrostatic barrier can be created by junctions
Conductivity when charge carriers have enough energy to overcome barrier (usually thermionic emission)
PN Junctions
• When an n-type and a p-type semiconductor are brought into contact a pn junction is formed --- acts as a diode
• Carriers: electrons and lack of electrons (holes)
04/22/23 ELCT564
• n-type: majority electrons, p-type: majority holes
• When in contact electrons + holes diffuse across the interface and they recombine when they reach the opposite layer—until thermal equilibrium
• Electric field that stops diffusion is set up – V0 contact potential depends on doping concentrations on each side
Depletion region is formed (no carriers)
• If external voltage is applied --- junction is biased, net flow of charge and energy• Forward bias: reduces potential difference from |V0| to |V0 | - |Vext|net current flow from p-side to n-side
• Reverse bias: increases potential difference from |V0 | to |V0 | + |Vext|carriers cannot overcome the additional barrier--- little current due to the charge
densities
Diodes
04/22/23 ELCT564
• When an ohmic contact is placed on the surface of the n-doped semiconductor only majority carrier diffusion dominates the junction performance
• Free electrons that enter the metal have positively charged region depleted of carriers just underneath the metal contact
• This positive charge gives rise to an electrostatic barrier V0
• Fwd-bias diffusion current from electrons in semiconductor dominates
Diodes
Practical Diodes
04/22/23 ELCT564
• Finite resistivity of the bulk semiconductor----voltage drop--- reduces the fraction of the applied voltage that appears across the junction
• Current shows a saturation tendency
Transistor
04/22/23 ELCT564
GaAs MESFET
BJT
Minimum transit time from emitter to collector
BJTs are planar and made of si in the npn typeLow cost and reliable solution below 4 GHz
Applications: small signal amplifiers, linear power amplifiers, low noise amplifiers and oscillaors
Use ion-implantation for fabrication and self-alignment:Multi-finger emitter-base construction
Transistor Model
04/22/23 ELCT564
More advanced hybrid-p modelModel for packaged transistorsLp ~ 0.2 to 1nHCp ~ 0.01 to 0.05 pF
Advanced CAD programs allow designers to compare measured s-parameters of transistor with those obtained from model.
Field Effect Transistors
04/22/23 ELCT564
Metal- semiconductor field-effect transistor
Gate terminal uses a Schottky barrier gate
Microwave FETS with GaAs– greater e- mobility– f>4GHZExcellent freq. response & noise performance
Mixers and Detectors
04/22/23 ELCT564
Use non-linear characteristic of device to generate an output signal containing many frequency components
Detection
Diode is receiving only one high frequency ωRF
DC term which includes information about the amplitude of the RF signal
Diode sensitivity = PDC/ PRF
Frequency diagram of a detector diode
Mixing
04/22/23 ELCT564
Required in order to get amplitude +phase information
Need two high (RF) frequencies close to each other RF frequency and LO frequency (produced by a local oscillator)
Goals for the design of a good mixer
Optimum match for the RF and LO signals at RF & LO ports
Suppression of the DC component at RF, LO, IF portsOptimum match for the IF at the IF port
Optimum termination of higher harmonics at RF, LO & IF ports
Mixer Diode
04/22/23 ELCT564
Let’s assume that the incoming signal to the diode is the superposition of the RF & LO as shown below:
Single Diode Mixers
04/22/23 ELCT564
Fundamental to the design of all mixers
Every mixer can be scaled down to a single diode one
At very high frequencies exhibit best performance in terms of Lc
But not that good in terms of RF/LO isolation
Problems : Leakage of IF through RF/LO ports, leakage of RF/LO through IF port, leakage of DC through all ports, coupling between RF and LO, mismatch between RF/LO and IF ports and the diode --- need to modify circuits
• Transfer of RF, LO powers to the diode is optimized by using matching networks
• Transfer of IF power from diode to connecting circuits is optimized by appropriate design + choice of diode
• Image frequency has to be determined & isolated from RF/LO & IF ports
Microstrip Single Diode Mixer
04/22/23 ELCT564
Single diode mixers are not used effectively or frequently at microwave frequencies
Found more often in single balanced mixers
IF filter extracts only desired frequenciesand matches ZIF
Single stub match for ZRF /LO
fLO =20 GHz, fIF =1 GHz
fRF fLO+ fIF
Mixer Measurements
04/22/23 ELCT564
Conversion loss: Lc =10log(PRF /PIF)(if using BJT & FET – conversion gain!!)
Calibrate RF, LO powers before measurement
Find cable losses
Calibrate Spectrum analyzer
Noise FigureUse N.F. meter
Balanced Mixers
04/22/23 ELCT564
Single diode mixers are easy to make but have difficulty in isolating the RF from LO ports --- balanced mixers overcome this problem
Also give cancellation of AM noise from the local oscillator
Single balanced mixers• 2 complete single diode mixers connected
to mutually isolated ports of a hybrid
• RF & LO connecting to mutually isolated ports
• IF outputs are usually connected in parallel or combined through another hybrid
180o Hybrid Balanced Mixer
04/22/23 ELCT564
Microstrip configuration
Vd1=VRF + VLO
Vd2=VRF - VLO
In to get a non-zero IF --- 2 diodes are connected in ananti-parallel configuration.
Rat-race Mixer
04/22/23 ELCT564
not appropriate for all applications but have simple design, low LO requirements and simplebias circuit
Example of a mixer used in an integrated low-noise receiver
IF output is filtered directly from the ring and low frequency blocks are used on the RF and LO lines
Anti-parallel diode mixer
Double Balanced Mixer
04/22/23 ELCT564
• Suppresses even harmonics of both LO + RF
• Four diodes in configuration
• Very low conversion loss
Image Rejection Mixer
Fabricated Monolithic FGC Mixer