electrical sor

74
SOR 1 SCHEDULE OF RATES Item Description Unit Rate ($) POINT WIRING * Surface wiring in 1.5 mm2 PVC cable and 1.5 mm2 PVC earth cable in PVC trunking including accessories but excluding fittings, fan regulators and fans * ( 1 - 7 ) 1 One lighting or fan point controlled by a 1-gang No 23.80 switch (trunking run not exceeding 18m) 2 One lighting or fan point controlled by a 1-gang No 32.40 switch ( trunking run not exceeding 8m but not exceeding 12m ) 3 Two lighting or fan points controlled by a 2-gang No 47.30 switch ( trunking run not exceeding 12m) 4 Three lighting or fan points controlled by a 3-gang No 73.20 switch ( trunking run not exceeding 18m) 5 Each additional lighting or fan point to item 1, 2, 3 or No 13.20 4 ( Trunking run not exceeding 5m) 6 Each additional lighting or fan point to item 1, 2, 3 or No 26.50 4 ( trunking run exceeding 5m but not exceeding 10m) 7 One lighting points or fan controlled by two 2-way No 36.20 switches (trunking run not exceeding 12m) * Metal conduit wiring in 2 x 1.5mm2 PVC/PVC sheathhed cables and 1.5mm2 PVC earth cable to lighting points including 20mm diameter galvanised steel conduits and surface mounted metal clad plateswitches (batten lampholders ceiling roses, mounting blocks to be measured separately) * ( 8 - 15) 8 One lighting point controlled by a 1-gang switch No 49.50 (conduit run not exceeding 8m) 9 One lighting point controlled by a 1-gang switch No 66.00 (conduit run exceeding 8m but not exceeding 12m) 10 Two lighting points controlled by a 2-gang switch No 74.00 (conduit run not exceeding 12m) 11 Three lighting points controlled by a 3-gang switch No 113.90 (conduit run not exceeding 18m) CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Upload: kokuei

Post on 02-Dec-2014

2.015 views

Category:

Documents


22 download

TRANSCRIPT

Page 1: Electrical SOR

SOR 1SCHEDULE OF RATES

Item Description Unit Rate ($)

POINT WIRING

* Surface wiring in 1.5 mm2 PVC cable and 1.5 mm2

PVC earth cable in PVC trunking including

accessories but excluding fittings, fan regulators

and fans * ( 1 - 7 )

1 One lighting or fan point controlled by a 1-gang No 23.80

switch (trunking run not exceeding 18m)

2 One lighting or fan point controlled by a 1-gang No 32.40

switch ( trunking run not exceeding 8m but

not exceeding 12m )

3 Two lighting or fan points controlled by a 2-gang No 47.30

switch ( trunking run not exceeding 12m)

4 Three lighting or fan points controlled by a 3-gang No 73.20

switch ( trunking run not exceeding 18m)

5 Each additional lighting or fan point to item 1, 2, 3 or No 13.20

4 ( Trunking run not exceeding 5m)

6 Each additional lighting or fan point to item 1, 2, 3 or No 26.50

4 ( trunking run exceeding 5m but not exceeding 10m)

7 One lighting points or fan controlled by two 2-way No 36.20

switches (trunking run not exceeding 12m)

* Metal conduit wiring in 2 x 1.5mm2 PVC/PVC

sheathhed cables and 1.5mm2 PVC earth cable

to lighting points including 20mm diameter

galvanised steel conduits and surface mounted

metal clad plateswitches (batten lampholders ceiling

roses, mounting blocks to be measured separately)

* ( 8 - 15)

8 One lighting point controlled by a 1-gang switch No 49.50

(conduit run not exceeding 8m)

9 One lighting point controlled by a 1-gang switch No 66.00

(conduit run exceeding 8m but not exceeding 12m)

10 Two lighting points controlled by a 2-gang switch No 74.00

(conduit run not exceeding 12m)

11 Three lighting points controlled by a 3-gang switch No 113.90

(conduit run not exceeding 18m)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 2: Electrical SOR

SOR 2SCHEDULE OF RATES

Item Description Unit Rate ($)

12 Each additional lighting point to item 8, 9, 10 or 11 No 26.50

(conduit run not exceeding 5m)

13 Each additional lighting point to item 8, 9, 10 or 11 No 48.50

(conduit run exceeding 5m but not exceeding 10m )

14 One lighting point controlled by a 2-way switches No 87.00

(conduit run not exceeding 12m)

15 One fan point controlled by one switch excluding No 66.00

regulator (To a distance not exceeding 12m)

* PVC conduit wiring in 2 x 1.5mm2 PVC / PVC

sheathed cables and 1.5mm2 earth cable (green) to

lighting points including 20mm diameter PVC

conduits and surface mounted metal clad,

plateswitches (batten lampholers, ceiling roses,

mounting blocks to be measured separately)

* ( 16 to 23 )

16 One lighting point controlled by a 1-gang switch No 28.40

(conduit run not exceeding 8m )

17 One lighting point controlled by a 1-gang switch No 41.30

(conduit run exceeding 8m but not exceeding 12m )

18 Two lighting points controlled by a 2-gang switch No 50.20

( conduit run not exceeding 12m )

19 Three lighting points controlled by a 3-gang switch No 78.70

( conduit run not exceeding 18m )

20 Each additional lighting point to item 16, 17,18 or 19 No 13.10

(conduit run exceeding 5m )

21 Each additional lighting point to item 16, 17,18 or 19 No 26.20

(conduit run exceeding 5m but not exceeding 10m )

22 One lighting point controlled by two 2-way switches No 61.00

( conduit run not exceeding 12m )

23 One fan point controlled by one switch excluding No 37.80

regulator (To a distance not exceeding 12m)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 3: Electrical SOR

SOR 3SCHEDULE OF RATES

Item Description Unit Rate ($)

PUBLIC LIGHTING POINT AND WIRING

24 Public lighting points with wiring in 1.5mm2 / 3 - No 28.70

core PVC flat cables including PVC trunking

(ceiling roses, mounting blocks, wiring in PVC

counduits for vertical run to be measured

separately) (trunking run not exceeding 12m)

25 Public lighting points with wiring in 1.5mm2 / 3 - No 40.20

core PVC flat cables including PVC trunking

(ceiling roses, mounting blocks, wiring in PVC

counduits for vertical run to be measured

separately) (trunking run exceeding 12m but not

exceeding 16m)

26 Extra over item 24 and 25 for wiring using 20mm No 6.70

diameter PVC conduit for vertical run from floor

to ceiling

POWER POINT AND WIRING

27 One 13A switchsocket outlet (1-gang) with wiring No 37.90

in 2.5mm2 / 3 - core PVC / PVC sheathed flat cables

including 40 x 20 (mm) PVC trunking and surface

mounted white plate switchsocket outlet (trunking

run not exceeding 12m)

28 One 13A switchsocket outlet (2-gang) with wiring No 44.90

in 2.5mm2 / 3 - core PVC / PVC sheathed flat cables

including 40 x 20 (mm) PVC trunking and surface

mounted white plate switchsocket outlet (trunking

run not exceeding 12m)

29 One 13A metal clad switchsocket outlet (1-gang) No 64.30

with wiring in 2.5mm2 / 3 - core PVC / PVC sheathed

flat cables including 20 mm diameter galvanised

steel conduits and metal clad switchsocket outlet

( conduit run not exceeding 12m)

30 One 13A metal clad switchsocket outlet (1-gang) No 45.00

with wiring in 2.5mm2 / 3 - core PVC / PVC sheathed

flat cables including 20 mm diameter PVC conduit

metal clad switchsocket outlet

( conduit run not exceeding 12m)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 4: Electrical SOR

SOR 4SCHEDULE OF RATES

Item Description Unit Rate ($)

31 One 15A switchsocket outlet (1-gang) with wiring No 46.10

in 2.5 mm2/3 - core PVC / PVC sheathed flat cables

including 40 x 20 (mm) PVC trunking and surface

mounted white plate switchsocket outlet

(trunking run not exceeding 12m)

32 One 15A metal clad switchsocket outlet (1-gang) No 69.00

with wiring in 2.5mm2 / 3 - core PVC / PVC sheathed

flat cables including 20 mm diameter galvanised

steel conduits and metal clad switchsocket outlet

( conduit run not exceeding 12m)

33 One 15A metal clad switchsocket outlet (1-gang) No 49.50

with wiring in 2.5mm2 / 3 - core PVC / PVC sheathed

flat cables including 20 mm diameter PVC conduit

steel conduits and metal clad switchsocket outlet

( conduit run not exceeding 12m)

34 One 20A water heater point with wiring in 2 x 6mm2 No 65.40

PVC / PVC cable with 6mm2 PVC earth (green)

including 40 x 20 (mm) PVC trunking, surfaced

mounted water heater switch (MARKED WATER

HEATER AND WITH PILOT LAMP) and 20A

connection unit ( trunking run not exceeding 12m)

RISING MAINS / SUBMAINS / CIRCUIT WIRING

35 Rising mains of 4 x 150 mm2 600 / 1000 volts m 76.50

PVC/PVC sheathed cables c/w 70mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

36 Rising mains of 4 x 120 mm2 600 / 1000 volts m 65.00

PVC/PVC sheathed cables c/w 70mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

37 Rising mains of 4 x 95 mm2 600 / 1000 volts m 51.00

PVC/PVC sheathed cables c/w 50mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 5: Electrical SOR

SOR 5SCHEDULE OF RATES

Item Description Unit Rate ($)

38 Rising mains of 4 x 70 mm2 600 / 1000 volts m 39.00

PVC/PVC sheathed cables c/w 35mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

39 Rising mains of 4 x 50 mm2 600 / 1000 volts m 31.00

PVC/PVC sheathed cables c/w 25mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

40 Rising mains of 4 x 35 mm2 600 / 1000 volts m 25.50

PVC/PVC sheathed cables c/w 16mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

41 Rising mains of 4 x 25 mm2 600 / 1000 volts m 16.50

PVC/PVC sheathed cables c/w 16mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

42 Rising mains of 4 x 16 mm2 600 / 1000 volts m 11.50

PVC/PVC sheathed cables c/w 16mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

43 Rising mains of 4 x 10 mm2 600 / 1000 volts m 8.20

PVC/PVC sheathed cables c/w 10mm2 PVC earth

cable supplied and properly fixed including all

labour, PVC/galvanised steel band, staples, clips

& all necessary connection ( metal trunking/tray to

be measured separately )

44 Submains/Circuit wiring of 2 x 25 mm2 600/1000 m 8.40

volts PVC/PVC sheathed cables and 16mm2 PVC

sheathed earth wire supplied and properly installed

including labour for laying/drawing & all necessary

connections (PVC trunking, cocnduits to be

measured separately)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 6: Electrical SOR

SOR 6SCHEDULE OF RATES

Item Description Unit Rate ($)

45 Submains/Circuit wiring of 2 x 16 mm2 600/1000 m 6.40

volts PVC/PVC sheathed cables and 16mm2 PVC

sheathed earth wire supplied and properly installed

including labour for laying/drawing & all necessary

connections (PVC trunking, cocnduits to be

measured separately)

46 Submains/Circuit wiring of 2 x 10 mm2 600/1000 m 5.40

volts PVC/PVC sheathed cables and 10mm2 PVC

sheathed earth wire supplied and properly installed

including labour for laying/drawing & all necessary

connections (PVC trunking, cocnduits to be

measured separately)

47 Submains/Circuit wiring of 2 x 6 mm2 600/1000 m 4.30

volts PVC/PVC sheathed cables and 6mm2 PVC

sheathed earth wire supplied and properly installed

including labour for laying/drawing & all necessary

connections (PVC trunking, cocnduits to be

measured separately)

48 Submains/Circuit wiring of 2 x 4 mm2 600/1000 m 3.20

volts PVC/PVC sheathed cables and 4mm2 PVC

sheathed earth wire supplied and properly installed

including labour for laying/drawing & all necessary

connections (PVC trunking, cocnduits to be

measured separately)

49 Circuit wiring of 2 x 2.5 mm2 600/1000 volts PVC/PVC m 2.80

sheathed cables and 2.5mm2 PVC sheathed earth

wire supplied and properly installed including

labour for laying/drawing & all necessary connections

(PVC trunking, conduits to be measured separately)

50 Circuit wiring of 2 x 1.5 mm2 600/1000 volts PVC/PVC m 2.10

sheathed cables and 1.5mm2 PVC sheathed earth

wire supplied and properly installed including

labour for laying/drawing & all necessary connections

(PVC trunking, conduits to be measured separately)

51 Wiring in 2 x 4 mm2 600 / 1000 volts PVC and 4mm2 m 2.80

PVC and 4mm2 PVC earth wire supplied and properly

installed including labour for laying / drawing &

all necessary connection to the point of supply

(PVC trunking, conduit measured sepatetely)

52 Wiring in 2 x 2.5 mm2 600 / 1000 volts PVC and m 2.10

2.5mm2 PVC earth wire supplied and properly

installed including labour for laying / drawinng &

all necessary connection to the point of supply

(PVC trunking, conduit measured separately )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 7: Electrical SOR

SOR 7SCHEDULE OF RATES

Item Description Unit Rate ($)

53 Wiring in 2 x 1.5 mm2 600 / 1000 volts PVC and m 1.60

1.5mm2 PVC earth wire including labour for laying /

drawing & all necessary connection to the point

of supply ( conduit measured separately )

54 1 x 1.5 mm2 single PVC sheathed green & yellow m 0.40

colour earth wires including fixing staples or clips

55 1 x 2.5 mm2 single PVC sheathed green & yellow m 0.50

colour earth wires including fixing staples or clips

56 1 x 4 mm2 single PVC sheathed green & yellow m 0.70

colour earth wires including fixing staples or clips

57 1 x 6 mm2 single PVC sheathed green & yellow m 1.00

colour earth wires including fixing staples or clips

58 1 x 10 mm2 single PVC sheathed green & yellow m 1.40

colour earth wires including fixing staples or clips

59 1 x 16 mm2 single PVC sheathed green & yellow m 2.00

colour earth wires including fixing staples or clips

60 1 x 25 mm2 single PVC sheathed green & yellow m 3.00

colour earth wires including fixing staples or clips

61 1 x 35 mm2 single PVC sheathed green & yellow m 3.60

colour earth wires including fixing staples or clips

62 1 x 50 mm2 single PVC sheathed green & yellow m 4.80

colour earth wires including fixing staples or clips

63 1 x 70 mm2 single PVC sheathed green & yellow m 5.50

colour earth wires including fixing staples or clips

64 1 x 10 mm2 single PVC sheathed green & yellow m 1.30

colour earth wires including fixing staples or clips

65 1 x 16 mm2 single PVC sheathed green & yellow m 1.80

colour earth wires including fixing staples or clips

66 1 x 25 mm2 single PVC sheathed green & yellow m 2.80

colour earth wires including fixing staples or clips

67 1 x 50 mm2 single PVC sheathed green & yellow m 5.10

colour earth wires including fixing staples or clips

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 8: Electrical SOR

SOR 8SCHEDULE OF RATES

Item Description Unit Rate ($)

* Wiring in Mineral Insulated Copper Cable with

PVC sheath (MICC/PVC) including all clips, staples

and fixing accessories (cable tray and terminating

and connecting accessories to be measured

separately) * 68 to 80

68 10 mm2 4 core cable m 35.30

69 16 mm2 4 core cable m 50.20

70 25 mm2 4 core cable m 51.60

71 4 x 50 mm2 single core cable m 74.00

72 4 x 70 mm2 single core cable m 125.80

73 4 x 95 mm2 single core cable m 211.00

74 4 x 120 mm2 single core cable m 252.70

75 Sealing assembly / cable link for MICC / PVC No. 8.80

sheathed cable 10 - 25mm2

76 Sealing assembly / cable link for MICC / PVC No 12.00

sheathed cable 35 - 50mm2

77 Sealing assembly / cable link for MICC / PVC No 14.70

sheathed cable 70 - 120mm2

78 Gland for MICC/PVC cable size 10 - 25mm2 No 10.30

79 Gland for MICC/PVC cable size 35 - 50mm2 No 17.50

80 Gland for MICC/PVC cable size 95 - 120mm2 No 20.40

FIRE RESISTANT CABLES

(S'pore Cable Manufacturer, Fujikuca, Sigma, Tian Sin)

81 Wiring in 4 x 16 mm2 600/1000 volts PE or EPR with m 24.50

PVC sheath including clips, staples and fixing

accessories ( cable trunking/ tray to be measured

separately)

82 Wiring in 4 x 25 mm2 600/1000 volts PE or EPR with m 32.50

PVC sheath including clips, staples and fixing

accessories ( cable trunking/ tray to be measured

separately)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 9: Electrical SOR

SOR 9SCHEDULE OF RATES

Item Description Unit Rate ($)

83 Wiring in 4 x 35 mm2 600/1000 volts PE or EPR with m 45.30

PVC sheath including clips, staples and fixing

accessories ( cable trunking/ tray to be measured

separately)

84 Wiring in 4 x 50 mm2 600/1000 volts PE or EPR with m 54.60

PVC sheath including clips, staples and fixing

accessories ( cable trunking/ tray to be measured

separately)

85 Wiring in 4 x 70 mm2 600/1000 volts PE or EPR with m 68.10

PVC sheath including clips, staples and fixing

accessories ( cable trunking/ tray to be measured

separately)

UNDERGROUND CABLES

( S' pore Cable Manufacturer, Sigma, Tai Sun, Wilson)

86 Underground cable of 4mm2 3-core 600/1000 volts m 2.80

PVC/SWA/PVC including laying in trench but

exclude excavation

87 Underground cable of 6mm2 2-core 600/1000 volts m 3.10

PVC/SWA/PVC including laying in trench but

exclude excavation

88 Underground cable of 6mm2 3-core 600/1000 volts m 3.60

PVC/SWA/PVC including laying in trench but

exclude excavation

89 Underground cable of 10mm2 2-core 600/1000 volts m 4.60

PVC/SWA/PVC including laying in trench but

exclude excavation

90 Underground cable of 10mm2 3-core 600/1000 volts m 5.20

PVC/SWA/PVC including laying in trench but

exclude excavation

91 Underground cable of 16mm2 2-core 600/1000 volts m 6.60

PVC/SWA/PVC including laying in trench but

exclude excavation

92 Underground cable of 25mm2 2-core 600/1000 volts m 9.80

PVC/SWA/PVC including laying in trench but

exclude excavation

93 Underground cable of 50mm2 2-core 600/1000 volts m 16.20

PVC/SWA/PVC including laying in trench but

exclude excavation

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 10: Electrical SOR

SOR 10SCHEDULE OF RATES

Item Description Unit Rate ($)

94 Underground cable of 6mm2 4-core 600/1000 volts m 4.20

PVC/SWA/PVC including laying in trench but

exclude excavation

95 Underground cable of 10mm2 4-core 600/1000 volts m 8.20

PVC/SWA/PVC including laying in trench but

exclude excavation

96 Underground cable of 16mm2 4-core 600/1000 volts m 10.90

PVC/SWA/PVC including laying in trench but

exclude excavation

97 Underground cable of 25mm2 4-core 600/1000 volts m 16.50

PVC/SWA/PVC including laying in trench but

exclude excavation

98 Underground cable of 35mm2 4-core 600/1000 volts m 22.30

PVC/SWA/PVC including laying in trench but

exclude excavation

99 Underground cable of 50mm2 4-core 600/1000 volts m 28.60

PVC/SWA/PVC including laying in trench but

exclude excavation

100 50mm diameter, UPVC Class C pipe for road crossing m 3.20

laid in trench ( trench measured separately )

101 80mm diameter, UPVC Class C pipe for road crossing m 5.60

laid in trench ( trench measured separately )

102 100mm diameter, UPVC Class C pipe for road crossing m 9.30

laid in trench ( trench measured separately )

103 150mm diameter, UPVC Class C pipe for road crossing m 20.00

laid in trench ( trench measured separately )

104 Excavate trench for underground cable / road crossing m 6.70

pipes 600mm wide and not exceeding 750mm deep

including sand blinding and backfill of earth

105 Excavate trench for underground cable / road crossing m 8.80

pipes 600mm wide exceeding 750mm and not exceeding

1.0m deep including sand blinding and backfill of earth

106 Excavate pit 1m x 1m x 750mm deep and backfilling Nos 12.00

107 Breaking up macadam road surface 600mm wide and m 17.10

not exceeding 300mm thick including taking up pitch

block base and reinstate same on completion

108 Breaking up reinforced concrete slab not exceeding m2 40.00

150mm thick, remove debris off site and reinstate

including making good to match existing

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 11: Electrical SOR

SOR 11SCHEDULE OF RATES

Item Description Unit Rate ($)

109 Breaking up reinforced concrete drain ( exceeding m 52.50

300mm deep ) and reinstate on completion to match

existing

110 1000 or 2000 x 150 x 2 mm thick UPVC cable cover m 4.00

pleates as warning or protective cover in trench

CONDUIT

( Barton, Maruchi, Walsall, Burns)

111 20mm diameter galvanised steel conduit fixed to wall, m 8.00

or ceiling complete with spacer bar, saddles,

inspection boxes / junctions / bends / tees, elbows

and joints accessories

112 25mm diameter galvanised steel conduit fixed to wall, m 8.80

or ceiling complete with spacer bar, saddles,

inspection boxes / junctions / bends / tees, elbows

and joints accessories

113 32mm diameter galvanised steel conduit fixed to wall, m

or ceiling complete with spacer bar, saddles, 11.20

inspection boxes / junctions / bends / tees, elbows

and joints accessories

114 20mm diameter super high impact heavy gauge PVC m 2.70

conduit fixed to wall or ceiling complete with spacer

bas, saddles, inspection boxes / junctions / bends /

tees, elbows and joint accessories

115 25mm diameter super high impact heavy gauge PVC m 3.00

conduit fixed to wall or ceiling complete with spacer

bas, saddles, inspection boxes / junctions / bends /

tees, elbows and joint accessories

116 32mm diameter super high impact heavy gauge PVC m 4.20

conduit fixed to wall or ceiling complete with spacer

bas, saddles, inspection boxes / junctions / bends /

tees, elbows and joint accessories

117 38mm diameter super high impact heavy gauge PVC m 7.50

conduit fixed to wall or ceiling complete with spacer

bas, saddles, inspection boxes / junctions / bends /

tees, elbows and joint accessories

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 12: Electrical SOR

SOR 12SCHEDULE OF RATES

Item Description Unit Rate ($)

PVC TRUNKINGS

118 Approved 40mm x 20mm single compartment PVC m 3.40

trunking including fixing to wall or ceiling all PVC

clips and joint accessories

119 Approved 40mm x 16mm single compartment PVC m 3.00

trunking including fixing to wall or ceiling all PVC

clips and joint accessories

120 Approved 80mm x 32mm two compartment PVC m 8.50

trunking including fixing to wall or ceiling all PVC

clips and joint accessories

121 Approved 60mm x 20mm two compartment PVC m 5.80

trunking including fixing to wall or ceiling all PVC

clips and joint accessories

122 Approved 32mm x 16mm single compartment PVC m 2.20

trunking including fixing to wall or ceiling all PVC

clips and joint accessories

123 Approved 25mm x 12.50mm single compartment PVC m 2.00

trunking including fixing to wall or ceiling all PVC

clips and joint accessories

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 13: Electrical SOR

SOR 13SCHEDULE OF RATES

Item Description Unit Rate ($)

METAL TRUNKING

(Ekko, Sakiya, Li-Soon )

* Electro Galvanised Metal Trunking complete with

coupling, detachable cover, screws and joint

accessories and finshed with epoxy paint and

including fixing to walls or ceilings ( * 124 144 )

124 1.2mm thick 50 x 50 mm trunking m 10.20

125 1.2mm thick 75 x 50 mm trunking m 11.80

126 1.2mm thick 75 x 75 mm trunking m 13.10

127 1.2mm thick 100 x 25 mm trunking m 11.80

128 1.2mm thick 100 x 50 mm trunking m 13.20

129 1.2mm thick 100 x 75 mm trunking m 14.50

130 1.4mm thick 110 x 100 mm trunking m 18.10

131 1.4mm thick 125 x 50 mm trunking m 16.30

132 1.4mm thick 150 x 25 mm trunking m 16.30

133 1.4mm thick 150 x 50 mm trunking m 18.20

134 1.4mm thick 150 x 75 mm trunking m 20.10

135 1.4mm thick 150 x 100 mm trunking m 22.20

136 1.6mm thick 150 x 150 mm trunking m 26.10

137 1.6mm thick 175 x 50 mm trunking m 21.00

138 1.6mm thick 200 x 50 mm trunking m 22.70

139 1.6mm thick 200 x 75 mm trunking m 24.20

140 1.6mm thick 200 x 100 mm trunking m 26.50

141 1.6mm thick 225 x 50 mm trunking m 24.20

142 1.6mm thick 250 x 50 mm trunking m 26.70

143 1.6mm thick 300 x 25 mm trunking m 29.40

144 1.6mm thick 300 x 50 mm trunking m 31.30

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 14: Electrical SOR

SOR 14SCHEDULE OF RATES

Item Description Unit Rate ($)

* Electro galvanised steel trunking detachable cover

finished with epoxy coating and fixed to existing

trunking ( 145 161 )

145 1.2mm thick 50 x 25 mm trunking cover m 3.30

146 1.2mm thick 50 x 50 mm trunking cover m 3.50

147 1.2mm thick 75 x 50 mm trunking cover m 4.10

148 1.2mm thick 75 x 75 mm trunking cover m 4.10

149 1.2mm thick 100 x 25 mm trunking cover m 5.00

150 1.2mm thick 100 x 50 mm trunking cover m 5.00

151 1.2mm thick 100 x 75 mm trunking cover m 5.00

152 1.2mm thick 100 x 100 mm trunking cover m 5.10

153 1.2mm thick 125 x 50 mm trunking cover m 5.80

154 1.2mm thick 150 x 25 mm trunking cover m 6.60

155 1.2mm thick 150 x 50 mm trunking cover m 6.60

156 1.2mm thick 150 x 75 mm trunking cover m 6.60

157 1.2mm thick 150 x 100 mm trunking cover m 6.70

158 1.2mm thick 150 x 150 mm trunking cover m 6.90

159 1.2mm thick 175 x 50 mm trunking cover m 7.70

160 1.4mm thick 200 x 50 mm trunking cover m 9.80

161 1.4mm thick 200 x 756mm trunking cover m 9.80

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 15: Electrical SOR

SOR 15SCHEDULE OF RATES

Item Description Unit Rate ($)

CABLE TRAY

* Hot dipped galvanised perforated mild steel cable

tray including all hangers, supports and fixings

162 100mm width, 1.0mm thick m 14.90

163 150mm width, 1.0mm thick m 18.10

164 225mm width, 1.2mm thick m 21.10

165 300mm width, 1.6mm thick m 27.50

166 450mm width, 1.6mm thick m 42.00

167 600mm width, 2.0mm thick m 49.10

ELECTRICAL ACCESSORIES

* Supply and fix the following accessories and fittings

fittings includidng all necessary fiixing screws and

plastic plugs

168 5 Amp white rocker plate switch 1-way or 2-way No 7.00

complete with moulded surface mounting box

( MK, Delta, Crabtree, Tenby, Clipsal )

169 5 Amp white rocker 2 gang plate switch No 10.80

complete with moulded surface mounting box

( MK, Delta, Crabtree, Tenby, Clipsal )

170 5 Amp white rocker 3 gang plate switch No 11.60

complete with moulded surface mounting box

( MK, Delta, Crabtree, Tenby, Clipsal )

171 5 Amp white rocker 4 gang plate switch No 14.50

complete with moulded surface mounting box

( MK, Delta, Crabtree, Tenby, Clipsal )

172 5 Amp switchboard outlet ( 3-pin) shuttered and No 18.30

complete with moulded surface mounting box

( MK, Delta, Crabtree, Tenby, Clipsal )

173 13 Amp switchsocket-outlet complete with moulded No 9.60

mounting box

( MK, Delta, Crabtree, Tenby, Clipsal )

174 13 Amp switchsocket-outlet 2-gang complete with No 13.00

moulded surface mounting box

( MK, Delta, Crabtree, Tenby, Clipsal )

175 13 Amp metal clad switchsocket-outlet complete No 12.60

with box for surface mounting

( MK, Delta, Crabtree, Tenby, Clipsal )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 16: Electrical SOR

SOR 16SCHEDULE OF RATES

Item Description Unit Rate ($)

176 13 Amp metal clad switchsocket-outlet 2 gang complete No 21.60

with box for surface mounting

( MK, Delta, Crabtree, Tenby, Clipsal )

177 13 Amp weatherproof switchsocket-outlet complete No 68.00

with screw-on cap

178 15 Amp weatherproof switchsocket-outlet complete No 80.00

with screw-on cap

179 15 Amp switchsocket-outlet complete with moulded No 14.00

surface mounting box

( MK, Delta, Crabtree, Tenby, Clipsal )

180 15 Amp switchsocket-outlet metal clad complete No 18.00

with box for surface mounting box

181 13 Amp 3 pin fused plug No 4.00

182 15 Amp 3 pin plug top No 8.50

183 15 Amp 3 pin weatherproof plug No 32.80

184 20 Amp 5 pin SW socket No 90.00

185 5 Amp metal clad switch 1 gang No 11.70

( MK, Delta, Clipsal, PDL )

186 5 Amp metal clad switch 2 gang or 4 gang No 16.80

( MK, Delta, Clipsal, PDL )

187 White moulded insulated bayonet-type batten No 4.60

lampholder, 5 Amp with skirt, 3 terminals and

loop-in earth terminal similar to Delta Cat No. 1031

or other approved

188 White ceiling rose three terminals 5 Amp similar to No 4.90

Delta Cat No. 1200 or other approved

189 3-pin connectors (PVC) No 3.00

190 Polarised 10 Amp rated plug and socket connector No 3.00

191 Adaptors to Lamp Holders No 3.00

192 PVC mounting block No 1.80

193 20 Amp double pole water heater switch c/w pilot No 14.90

lamp and white moulded surface mounting box

194 45 Amp cooker double pole control switch No 32.10

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 17: Electrical SOR

SOR 17SCHEDULE OF RATES

Item Description Unit Rate ($)

195 20 Amp double pole switch c/w white moulded No 14.90

surface mounting box

196 20 Amp DP metal clad switch fuse c/w HRC fuse No 89.60

( Mem, Stromberg, Simplex )

197 32 Amp DP metal clad switch fuse c/w HRC fuse No 121.90

( Mem, Stromberg, Simplex )

198 63 Amp DP metal clad switch fuse c/w HRC fuse No 250.00

( Mem, Stromberg, Simplex )

199 100 Amp DP metal clad switch fuse c/w HRC fuse No 270.70

( Mem, Stromberg, Simplex )

200 20 Amp TPN metal clad switch fuse c/w HRC fuse No 112.40

( Mem, Stromberg, Simplex )

201 32 Amp TPN metal clad switch fuse c/w HRC fuse No 150.70

( Mem, Stromberg, Simplex )

202 63 Amp TPN metal clad switch fuse c/w HRC fuse No 283.00

( Mem, Stromberg, Simplex )

203 100 Amp DP metal clad switch fuse c/w HRC fuse No 450.80

( Mem, Stromberg, Simplex )

204 15 Amp Double pole metal clad isolator switch No 96.30

( Mem, Stromberg, Simplex )

205 32 Amp Double pole metal clad isolator switch No 107.80

( Mem, Stromberg, Simplex )

206 63 Amp Double pole metal clad isolator switch No 140.20

( Mem, Stromberg, Simplex )

207 20 Amp TPN metal clad isolator switch No 66.00

( Mem, Stromberg, Simplex )

208 32 Amp TPN metal clad isolator switch No 88.30

( Mem, Stromberg, Simplex )

209 63 Amp TPN metal clad isolator switch No 173.40

( Mem, Stromberg, Simplex )

210 100 Amp TPN metal clad isolator switch No 289.80

( Mem, Stromberg, Simplex )

211 Insulated consumer control unit complete with 40 Amp No 183.30

RCCB, 32 Amp DP or 63 Amp DP isolator and

4 x 5/20 Amp 6 KA MCB (ABB, Mem, Sunlight )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 18: Electrical SOR

SOR 18SCHEDULE OF RATES

Item Description Unit Rate ($)

212 Insulated consumer control unit complete with 40 Amp No 201.00

RCCB, 32 Amp DP or 63 Amp DP isolator and

6 x 5/20 Amp 6 KA MCB (ABB, Mem, Sunlight )

213 Insulated consumer control unit complete with 40 Amp No 230.80

RCCB, 32 Amp DP or 63 Amp DP isolator and

8 x 5/20 Amp 6 KA MCB (ABB, Mem, Sunlight )

214 Insulated consumer control unit complete with 40 Amp No 251.70

RCCB, 32 Amp DP or 63 Amp DP isolator and

10 x 5/20 Amp 6 KA MCB (ABB, Mem, Sunlight )

215 Insulated consumer control unit complete with 40 Amp No 284.30

RCCB, 32 Amp DP or 63 Amp DP isolator and

12 x 5/20 Amp 6 KA MCB (ABB, Mem, Sunlight )

216 Metal clad consumer control unit complete with No 192.20

40 Amp RCCB, 32 Amp DP or 63 Amp DP isolator

and 4 x 5/20 Amp 6 KA MCB

(ABB, Mem, Sunlight, F & G )

217 Metal clad consumer control unit complete with No 207.20

40 Amp RCCB, 32 Amp DP or 63 Amp DP isolator

and 6 x 5/20 Amp 6 KA MCB

(ABB, Mem, Sunlight, F & G )

218 Metal clad consumer control unit complete with No 230.20

40 Amp RCCB, 32 Amp DP or 63 Amp DP isolator

and 8 x 5/20 Amp 6 KA MCB

(ABB, Mem, Sunlight, F & G )

219 Metal clad consumer control unit complete with No 250.40

40 Amp RCCB, 32 Amp DP or 63 Amp DP isolator

and 10 x 5/20 Amp 6 KA MCB

(ABB, Mem, Sunlight, F & G )

220 Metal clad consumer control unit complete with No 272.80

40 Amp RCCB, 32 Amp DP or 63 Amp DP isolator

and 12 x 5/20 Amp 6 KA MCB

(ABB, Mem, Sunlight, F & G )

221 40 Amp DP Residual currens circuit breaker (ELCB) No 60.00

with 30mA tripping current complete with mounting

box (ABB, Mem, F & G, Hager)

222 63 Amp DP Residual currens circuit breaker (ELCB) No 76.00

with 30mA tripping current complete with mounting

box (ABB, Mem, F & G, Hager)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 19: Electrical SOR

SOR 19SCHEDULE OF RATES

Item Description Unit Rate ($)

223 Metal Clad split load consumer unit complete with No 243.00

40 Amp DP RCCB 63 Amp DP or 32 Amp DP isolator

6 x 5/20 Amp 6KA MCB (ABB, Mem, Sunlight )

224 Metal Clad split load consumer control unit complete No 275.50

with 60 Amp DP isolator 1 x 20A sp MCB, 40 Amp DP

ELCB with 7 x 5/20A 6KA sp MCB )

(ABB, Mem, Sunlight

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 20: Electrical SOR

SOR 20SCHEDULE OF RATES

Item Description Unit Rate ($)

CONNECTORS, CUT-OUTS, FUSE LINK &

TAP-OFF UNITS

225 30 Amp B.I connector, 'Lucy' or other approved No 8.70

226 60 Amp B.I connector, 'Lucy' or other approved No 9.90

227 100 Amp B.I connector, ' Quintela ' or other approved No 21.40

228 150 Amp B.I connector, ' Quintela ' or other approved No 32.90

229 200 Amp B.I connector, ' Quintela ' or other approved No 46.70

230 30 Amp Electrical Service Box complete with No 95.40

accessories ( ABB, Sunlight, Huat Heng, Seah & Lee)

231 60 Amp Electrical Service Box complete with No 74.00

accessories ( ABB, Sunlight, Huat Heng, Seah & Lee)

232 18 mm2 capacity line tape with hexagon screw and felt No 7.10

233 30 mm2 capacity line tape with hexagon screw and felt No 8.90

234 50 mm2 capacity line tape with hexagon screw and felt No 11.30

235 75 mm2 capacity line tape with hexagon screw and felt No 17.80

236 120 mm2 capacity line tape with hexagon screw and felt No 60.00

237 6 Amp HRC cartridge fuse link No 3.40

(Mem, English Electric, Legrand)

238 16 Amp HRC cartridge fuse link No 3.30

(Mem, English Electric, Legrand)

239 20 Amp HRC cartridge fuse link No 3.60

(Mem, English Electric, Legrand)

240 25 Amp HRC cartridge fuse link No 4.00

(Mem, English Electric, Legrand)

241 32 Amp HRC cartridge fuse link No 4.90

(Mem, English Electric, Legrand)

242 60 Amp HRC cartridge fuse link No 7.30

(Mem, English Electric, Legrand)

243 100 Amp HRC cartridge fuse link No 14.70

(Mem, English Electric, Legrand)

244 60 Amp HRC fuse with carrier and base No 35.30

( Mem, Legrand, Merlin Gerin, PDL )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 21: Electrical SOR

SOR 21SCHEDULE OF RATES

Item Description Unit Rate ($)

245 100 Amp HRC fuse with carrier and base No 49.00

( Mem, Legrand, Merlin Gerin, PDL )

246 20 Amp industrial bolted pattern HRC fuse link No 3.50

( Mem, English Electric, Legrand )

247 32 Amp industrial bolted pattern HRC fuse link No 3.50

( Mem, English Electric, Legrand )

248 40 Amp industrial bolted pattern HRC fuse link No 5.80

( Mem, English Electric, Legrand )

249 63 Amp industrial bolted pattern HRC fuse link No 5.80

( Mem, English Electric, Legrand )

250 100 Amp industrial bolted pattern HRC fuse link No 12.10

( Mem, English Electric, Legrand )

251 160 Amp industrial bolted pattern HRC fuse link No 13.50

( Mem, English Electric, Legrand )

252 200 Amp industrial bolted pattern HRC fuse link No 14.30

( Mem, English Electric, Legrand )

253 300 Amp industrial bolted pattern HRC fuse link No 21.50

( Mem, English Electric, Legrand )

254 400 Amp industrial bolted pattern HRC fuse link No 42.90

( Mem, English Electric, Legrand )

255 500 Amp industrial bolted pattern HRC fuse link No 51.50

( Mem, English Electric, Legrand )

256 600 Amp industrial bolted pattern HRC fuse link No 59.60

( Mem, English Electric, Legrand )

257 Single phase 60 Amp fused tap-off units complete No 161.10

with line-tap connectors, HRC fuse, carrier, holder,

neutral connector and earth link as specified

( ABB, Sunlight, Huat Heng, Soundtext )

258 Single phase tap off box complete with 60 Amp 25 KA No 292.20

240V DP MCCB, 2 x 95mm2 line-tap connectors,

BI connectors, earth connector and earthing terminal

( ABB, Sunlight, Huat Heng, Soundtext )

259 Single phase tap off box complete with 2 x 60 Amp 25 KA No 373.00

240V DP MCCB, 2 x 95mm2 line-tap connectors,

BI connectors, earth connector and earthing terminal

( ABB, Sunlight, Huat Heng, Soundtext )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 22: Electrical SOR

SOR 22SCHEDULE OF RATES

Item Description Unit Rate ($)

260 Three phase fused tap-off box complete with No 419.90

4 x 50 mm2 or 4 x 70mm2 line-tap connectors,

3 x 100A HRC fuse, carrier, holder and earth link

( ABB, Sunlight, Huat Heng, Soundtext )

261 Three phase fused tap-off box complete with No 373.90

4 x 50 mm2 or 4 x 70mm2 line-tap connectors,

3 x 63A HRC fuse, carrier, holder and earth link

( ABB, Sunlight, Huat Heng, Soundtext )

262 Three phase 60 Amp usfused tap-off units complete No 132.40

with 50 mm2 line-tap connectors, neutral connector

earth link as specified

( ABB, Sunlight, Huat Heng, Soundtext )

263 Three phase 100 Amp usfused tap-off units complete No 143.90

with 50 mm2 line-tap connectors, neutral connector

earth link as specified

( ABB, Sunlight, Huat Heng, Soundtext )

264 Electro-galvanised steel tap-off box cover, No 18.60

320mm x 250mm x 105mm c/w cam lock

265 Camlock to metal box enclosure c/w 2 Nos keys No 8.00

266 4mm cable lug No 1.30

267 6mm cable lug No 1.30

268 10mm cable No 1.40

269 16mm cable lug No 1.50

270 20mm cable lug No 1.60

271 25mm cable No 1.60

272 35mm cable lug No 1.80

273 50mm cable No 2.40

274 70mm cable No 2.80

275 95mm cable lug No 3.00

276 120mm cable lug No 3.60

277 150mm cable No 4.10

278 185mm cable lug No 5.30

279 240mm cable No 6.40

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 23: Electrical SOR

SOR 23SCHEDULE OF RATES

Item Description Unit Rate ($)

MCCB AND MCB

280 MCB with short circuit interrupting capacity minimum No 10.00

6 KA, 5 - 40 Amp SP 240V

(ABB, Merlin Gerin, Mitsubishi )

281 MCB with short circuit interrupting capacity minimum No 62.00

10 KA, 20 - 60 Amp SP 240V

(ABB, Merlin Gerin, Mitsubishi )

282 MCB with short circuit interrupting capacity minimum No 39.00

6 KA, 5 - 40 Amp DP 240V

(ABB, Merlin Gerin, Mitsubishi )

283 Moulded case circuit breaker ( MCCB) minimum No 131.70

25 KA short circuit interrupting capacity, 15 - 100Amp

240V DP (Hitachi, Merlin Gerin, Terasaki, Mitsubishi)

284 MCCB minimum 25 KA short circuit interrupting No 178.00

capacity, 15 - 100 Amp 415V TP

(Hitachi, Merlin Gerin, Nikko, Terasaki, Mitsubishi)

285 MCCB minimum 36 - 50 KA short circuit interrupting No 363.00

capacity, 125 - 225 Amp 415V TP

(Hitachi, Merlin Gerin, Nikko, Terasaki, Mitsubishi)

286 MCCB minimum 36 - 50 KA short circuit interrupting No 610.00

capacity, 250 - 400 Amp 415V TP

(Hitachi, Merlin Gerin, Nikko, Terasaki, Mitsubishi)

287 MCCB 50 KA short circuit interrupting No 1161.00

capacity, 450 - 600 Amp 415V TP

(Hitachi, Merlin Gerin, Nikko, Terasaki, Mitsubishi)

288 MCCB 50 KA short circuit interrupting No 1585.00

capacity, 700 - 800 Amp 415V TP

(Hitachi, Merlin Gerin, Nikko, Terasaki, Mitsubishi)

289 MCCB 50 KA short circuit interrupting No 1950.00

capacity, 1000 - 1600 Amp 415V TP

(Hitachi, Merlin Gerin, Nikko, Terasaki, Mitsubishi)

290 ACB minimum 36 KA 3 sec short-time withstand No 5598.00

capacity 800 - 1250A 415V TP c/w overload and

short-circuit protection control unit, drawout type

291 ACB minimum 36 KA 3 sec short-time withstand No 6407.00

capacity 800 - 1250A 415V 4P c/w overload and

short-circuit protection control unit, drawout type

292 ACB minimum 57 KA 3 sec short-time withstand No 9047.00

capacity 1600 - 2500A 415V TP c/w overload and

short-circuit protection control unit, drawout type

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 24: Electrical SOR

SOR 24SCHEDULE OF RATES

Item Description Unit Rate ($)

293 ACB minimum 57 KA 3 sec short-time withstand No 11500.00

capacity 1600 - 2500A 415V 4P c/w overload and

short-circuit protection control unit, drawout type

294 RCCB 63A 2P 30mA complete with built-in anti- No 74.00

nuisance tripping device and trip indication

(MG, Hager, F&G, ABB)

295 RCCB 63A 4P 30mA complete with built-in anti- No 110.00

nuisance tripping device and trip indication

(MG, Hager, F&G, ABB)

296 RCCB 40A 2P 30mA complete with built-in anti- No 57.00

nuisance tripping device and trip indication

(MG, Hager, F&G, ABB)

297 RCCB 40A 4P 30mA complete with built-in anti- No 106.00

nuisance tripping device and trip indication

(MG, Hager, F&G, ABB)

MAINWSITCHBOARD'S ACCESSORIES

* The following instruments or accessories includes all

necessary fixing screws, connecting cable *298 to 309)

298 Ammeter - current transformer operated No 47.00

( 0 to 100A or up to 1600A )

( Bult, Nitech, Rudolf )

299 Volmeter - rotary water type ( 0 to 500V ) No 57.30

( Celsa, Crompton )

300 Voltmeter & ammeter selector switch No 25.10

( K & N, Blueline, Selko, Telux )

301 Maximum demand ammeter ( 0 to 100A or up to 1600A, No 107.00

excluding current transformers ) (Celsa, Crompton )

302 Indicating lamp bulb complete with built-in No 13.20

transformer ( Ideelzumi, Telemencarique)

303 Indicating lamp ( led ) complete with built-in No 30.00

transformer

304 Easrth fault relay with built-in timer ( excluding No 348.10

injection test on site and current transformer )

(Kasuga, RMA)

305 Timer for earth relay / over current relay No 180.00

( TEC, Kasuga, Mitsubishi, National )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 25: Electrical SOR

SOR 25SCHEDULE OF RATES

Item Description Unit Rate ($)

306 Earth Fault relay without built-in timer No 297.80

( excluding injection test on site and current

transformer ) ( Kasuga, RMA)

307 DTL over current relay with built-in timer No 456.20

( excluding injection test on site and current

transformer ) ( Kasuga )

308 One set 3 nos. IDMTL overcurrent relay c/w metal No 4974.80

enclosure ( excluding injection test on site and

current transformer )

309 IDMTL overcurrent relay ( excluding injection test No 1662.80

on site and current transformer )

* Protective Transformer Class 5P10

* ( 310 to 315 )

310 CT Ration 100 / 5 ( Nitech, Bilt, Rudolf ) No 52.00

311 CT Ration 200 / 5 or 300 / 5 No 81.10

( Nitech, Bilt, Rudolf )

312 CT Ration 400 / 5 ( Nitech, Bilt, Rudolf ) No 101.80

313 CT Ration 600 / 5 or 800 / 5 No 108.70

( Nitech, Bilt, Rudolf )

314 CT Ration 1000 / 5 or 1200 / 5 No 110.70

( Nitech, Bilt, Rudolf )

315 CT Ration 1600 / 5 No 111.00

( Nitech, Bilt, Rudolf )

* Metering current transformer Class 1

* ( 316 to 320 )

316 CT Ratio 100 / 5 (Nitech, Bilt, Rudolf ) No 35.00

317 CT Ration 200/5 or 300/5 or 400/5 No 42.50

(Nitech, Bilt, Rudolf )

318 CT Ration 600/5 or 800/5 No 44.70

(Nitech, Bilt, Rudolf )

319 CT Ration 1000/5 or 1200/5 No 65.50

(Nitech, Bilt, Rudolf )

320 CT Ratio 1600 / 5 (Nitech, Bilt, Rudolf ) No 99.50

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 26: Electrical SOR

SOR 26SCHEDULE OF RATES

Item Description Unit Rate ($)

321 32A By-pass switch DP or TP No 49.40

( Blueline, Hitachi, Mitsubbishi, Stromberg )

322 30 Amp DP contactor No 81.00

( Blueline, Hitachi, Mitsubishi, Stromberg)

323 30 Amp 4P contactor No 81.00

( Blueline, Hitachi, Mitsubishi, Stromberg)

324 60 Amp DP contactor No 128.40

( Blueline, Hitachi, Mitsubishi, Stromberg)

325 60 Amp 4P contactor No 176.70

( Blueline, Hitachi, Mitsubishi, Stromberg)

326 " Horstmann " Type Y Quartz or other approved time No 175.10

switch with 150 hours battery reserve

327 Neutral link 60A rating No 11.00

328 Neutral link 100A rating No 13.30

329 Neutral link 200A rating No 38.60

330 Supply and fix Indoor Service Electrical Distribution Set 1693.00

Panels ( OG Box) comprising : -

4 Nos. 630 Strip Fuse Way

6 Nos. 630A Solid Link

3 Nos. 200 HRC Fuse Link

2 Nos. Cast Resin Insulator

3 Nos. 70mm2 Earth Braid c/w lugs

3 Nos. 70mm2 cable clip

1 No. 1720mm x 610mm x 350mm Metal Enclosure c/w

Panel Lock ( Sunlight, Suat Heng, Soundtrex,

Seah & Lee)

331 PUB electrical meter box complete with No 285.00

(1) 1 No. 32A/40A DP MCB type C 10KA

(2) 1 No. 32A DP MCB type B 10 KA

(3) 2 Nos. 3 way connector

(4) 1 set 2 x 10mm2 PVC cable

(5) 1 No. insulated enclosure ( IP40)

complete with UV stablished and water tight viewing

lens

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 27: Electrical SOR

SOR 27SCHEDULE OF RATES

Item Description Unit Rate ($)

FANS

332 Exhaust fan 300mm ( KCK, National, Mitsubishi) No 105.00

333 Exhaust fan 450mm High Pressure No 520.00

( Industrial Type )

( 1400 RPM ) (KDK, National, Mitsubishi )

334 Exhaust fan 600mm High Pressure No 800.00

( Industrial Type )

( 920 RPM ) (KDK, National, Mitsubishi )

335 Ceiling fan hook including cutting mortice in concrete No 5.90

336 Ceiling fan regulator No 16.00

337 1.5 diameter sweep ceiling fan complete with regulator No 88.00

and teak board (KDK, National, Mitsubishi)

338 400mm diameter wall bracket fan complete with No 153.00

pull cord regulator and switch

(KDK, National, Mitsubishi)

339 500mm diameter wall bracket fan complete with No 355.00

pull cord regulator and switch

(KDK, National, Mitsubishi)

340 Supply and fix 508mm (20") diameter "WING-TON" No 248.00

WALL FAN 240v, 1400 RPM 50 Hz model 303 (MG)

in replacement including removing of existing wall fan

341 Supply and fix 500mm (20") diameter "KDK" wall No 370.00

Model H50 CK in replacement including removing of

existing wall fan

342 Supply and fix 635mm (25") diameter 'WING-TON" No 270.00

wall fan 240v, 1400 RMP 50Hz

Model 303 ( MG ) in replacement including removing

of existing wall fan

343 Supply and fix 635mm (25") diameter "KOUKYU" No. 210.00

wall fan 240V, 1400 rpm 50 Hz

Model 303 (MG) in replacement including removing

of existing wall fan

344 Rewind of fan motor coil for 400mm or 500mm diameter No 40.30

wall bracket fan

345 Fan condenser for 400mm or 500mm diameter wall No 11.40bracket fan

346 400mm diameter Auto rotating ceiling fan No 182.00

(KDK, National, Mitsubishi )

347 Replacement of fan gear for industrial wall fan No 81.65

348 Repair wall fan coil No 168.00

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 28: Electrical SOR

SOR 28SCHEDULE OF RATES

Item Description Unit Rate ($)

LUMINAIRES

The following including flexible connecting cables,

screws or ramsets

349 Mounting channel fluorescent luminaires complete No 27.00

with 1 x 18W tube and low-loss ballast ( max 6.5 W )

( Amcol, Simlite, Trimex )

350 Mounting channel fluorescent luminaires complete No 28.00

with 1 x 36W tube and low-loss ballast ( max 6.5 W )

( Amcol, Simlite, Trimex )

351 Mounting channel fluorescent luminaires complete No 42.00

with 1 x 18W tube and PUB approved type with

SISIR sticker electronic ballast

352 Mounting channel fluorescent luminaires complete No 44.00

with 1 x 36W tube and PUB approved type with

SISIR sticker electronic ballast

353 Mounting channel fluorescent luminaires complete No 52.60

with 2 x 36W tube and low-ballast ( max 6.5 W)

( Amcol, Simlite, Trimex )

354 Mounting channel fluorescent luminaires No 75.00

Philips TC 058 / 136 c/w 1 x TLD 36W tube, low-loss

ballast (max. 6.5W) and prismatic diffuser

( Amcol, Simlite, Trimex )

355 GHIDINI wall mounted luminaire with 2 x 11W PL lamp No 106.00

Cat. No. OVALLA BL 1101.2

356 GHIDINI wall mounted luminaire with 2 x 9W PL lamp No 100.00

Cat. No. OVALLA BL 1101.1

357 THORN PLAZZA OS 50 wall mounted luminaire with No 272.40

1 x 50W MBF lamp

358 Matsushita HS 1002 Opal diffuser c/w 2 x PL 9W lamp No 145.76

359 Lucerne 270-G surface mounted wall light (IP54) c/w No 79.35

2 x 9W PL lamp and accessories

360 Bega 2491 wall light (IP45) c/w 1 x 26W PLC & accessories No 419.75

361 Goccia 2898 wall light c/w 2 x 9W PL lamp & gear No 98.90

362 Noral Santa / Milano, Frosted Lens, Silver Reflector, No 126.50

capacitor 4UF c/w 2D 38W Lamp

363 FABRIKANT 1014 wall mounted luminaire No 303.60

(IP54) c/w 1 x 18W PLC Lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 29: Electrical SOR

SOR 29SCHEDULE OF RATES

Item Description Unit Rate ($)

364 Thorn FRAS 218 2 x 18W fluorescent luminaires No 174.80

c/w FRV 236 louvres

365 ZUMTOBELL Cat No.HS1002 c/w 2 x 11W PL Lamp No 146.05

366 HILITE SSMF/HF/3018, SSMF/HF Hinged frame No 226.55

luminaire c/w diffuser framed with spring loaded &

catches c/w 3 x 18W/83 lamp

367 Metal reflector fluorescent luminaire complete with No 34.00

1 x 18W tube and low-loss ballast (max 6.5 W)

( Amcol, Simlite, Trimex )

368 Metal reflector fluorescent luminaire complete with No 40.10

1 x 36W tube and low-loss ballast (max 6.5 W)

( Amcol, Simlite, Trimex )

369 Metal reflector fluorescent luminaire complete with No 51.20

2 x 36W tube and low-loss ballast (max 6.5 W)

( Amcol, Simlite, Trimex )

370 Wire Guard fluorescent luminaire complete with No 36.50

1 x 18W tube and low-loss ballast (max 6.5W) and

integral cam-lock

( Amcol, Simlite, Trimex )

371 Wire Guard fluorescent luminaire complete with No 37.50

1 x 36W tube and low-loss ballast (max 6.5W) and

integral cam-lock

( Amcol, Simlite, Trimex )

372 Weatherproof fluorescent luminaire 'Philips' No 86.00

Cat No. TCW 075/136 complete with 1 x 36 W tube

or other approved.

(Thorlux , Simlite)

373 Weatherproof fluorescent luminaire 'Philips' No 109.00

Cat No. TCW 075/236 complete with 2 x 36 W tube

or other approved.

(Thorlux , Simlite)

374 Take down and remove existing fluorescent luminaire No 39.00

and tube, and replace with wire guard fluorescent

luminaire complete with 1 x 18W tube including flexible

connecting cable and ceiling rose, or polarised plug

and socket connector, screwed or ramseted to walls

or concrete

375 Take down and remove existing fluorescent luminaire No 41.50

and tube, and replace with wire guard fluorescent

luminaire complete with 1 x 36W tube including flexible

connecting cable and ceiling rose, or polarised plug

and socket connector, screwed or ramseted to walls

or concrete

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 30: Electrical SOR

SOR 30SCHEDULE OF RATES

Item Description Unit Rate ($)

376 Take down and remove existing fluorescent luminaire No 31.00

and tube, and replace with mounting channel fluorescent

luminaire complete with 1 x 18W tube including low-loss

ballast (max 6.5W), flexible connecting cable, ceiling

rose/polarised plug, socket connector, screwed or

ramseted to walls or concrete

377 Take down and remove existing fluorescent luminaire No 32.00

and tube, and replace with mounting channel fluorescent

luminaire complete with 1 x 36W tube including low-loss

ballast (max 6.5W), flexible connecting cable, ceiling

rose/polarised plug, socket connector, screwed or

ramseted to walls or concrete

The following includes necessary fixing screw and

accessories (when necessary):-

378 Tungsten incandescent lamp bulbs 15/40 watts No 1.60

379 Tungsten incandescent lamp bulbs 60/75/100 watts No 1.80

380 Lampholders for fluorescent lamp Pair 2.00

381 Starters for fluorescent lamps (Philips, Oscram) No 1.10

382 Fluorescent starter holder (square) in replacement No 1.30

383 Capacitor 3.25 mfd fluorescent lamps No 3.60

384 Capacitor 7.5 / 6.5 mfd for 40W fluorescent lamps No 5.80

385 Low loss 20W or 40W fluorescent ballast No 9.40

(ATCO, Helvar, Vossloh Schwabe)

386 Electronic ballast for single 20W or 40W fluorescent lamp No 30.00

(PUB approved type with SISIR sticker)

387 Electronic ballast for 2 x 40W fluorescent lamp No 40.00

(PUB approved type with SISIR sticker)

388 3 core flexible cables for fluorescent luminaire including No 1.10

connection to ceiling roses

389 50W / 80W / 125W high presssure mercury vapour No 16.20

lamp with E27 base (Philips or Oscram)

390 160W high presssure mercury vapour lamp (blended) No 19.60

(Philips, Oscram)

391 250W high presssure mercury vapour lamp No 41.40

(Philips, Oscram)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 31: Electrical SOR

SOR 31SCHEDULE OF RATES

Item Description Unit Rate ($)

392 Ballast (control gear) for operation of high pressure No 49.60

mercury vapour lamp 50W/80W/125W

(Philips, Schwabe, Helvar, Parmar)

393 Halide 400W mercury ballast No 75.50

(Philips, Vossioh Schwabe )

394 400W mercury lamp No 44.40

approved (Philips, Splendour, Osram, Sylvania )

395 70W SON lamp ballast, 'Philips' or other No 46.60

approved (Philips, Splendour, Sylvania )

396 70W SON lamp ignitor , 240v No 39.20

(Philips, Thorn, Parmar, Bag Tusgi)

397 Candle bulb 40W, 240V, E14 No 2.90

(Philips, Splendour, Sylvania , Osram, Tungram)

398 450/600mm energy saving fluorescent tube No 2.90

(daylight) of 18W

(Philips, Hitachi, Toshiba, Osram)

399 900mm 30 W energy saving fluorescent tube No 3.10

(daylight) of 30W

(Philips, Hitachi, Toshiba, Osram)

400 1200mm 36 W energy saving fluorescent tube No 3.40

(daylight)

(Philips, Hitachi, Toshiba, Osram)

401 1500mm 36 W energy saving fluorescent tube No 3.90

(daylight) of 230V, 58W

(Philips, Hitachi, Toshiba, Osram)

402 6V, 3W indicating bulb for main switchboard No 1.30

(Ozon, Splendour, Sylvania)

403 600MM 18W energy saving fluorescent tube No 6.50

(warm white) (Philips colour 83, Splendour, Osram

Lumilux 31 Sylvania)

404 1200MM 18W energy saving fluorescent tube No 7.00

(warm white) (Philips colour 83, Splendour, Osram

Lumilux 31 Sylvania)

405 Supply and fix halogen lamp 12V 50W / 20W No 8.00

(Osram, Philip, Thorn)

406 Halogen Lamp HOFFIMISTER 0.35810-910 No 146.05

12V 50W c/w transofrmer

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 32: Electrical SOR

SOR 32SCHEDULE OF RATES

Item Description Unit Rate ($)

407 40W Circular tube (Daylight) No 6.80

(Ozon, Splendour, Osram, Sylavania)

408 SL 18W prismatic lamp No 22.00

(Philips, Splendour, Osram, Sylvania)

409 Philips' SL 25W prismatic lamp No 26.00

(Philip, Splendour, Osram, Sylvania)

410 Daylight / Warm white compact fluorescent lamp No 11.50

PL 5W / 7W / 9W

(Philip, Splendour, Osram, Sylvania)

411 Daylight / Warm white compact fluorescent lamp No 12.50

PL 11W

(Philip, Splendour, Osram, Sylvania)

412 Daylight / Warm white compact fluorescent lamp No 18.00

PLc 18W

(Philip, Splendour, Osram, Sylvania)

413 Daylight / Warm white compact fluorescent lamp No 20.00

PL 26W

(Philip, Splendour, Osram, Sylvania)

414 Daylight / Warm white compact fluorescent lamp No 19.00

PL 10W / 13W

(Philip, Splendour, Osram, Sylvania)

415 Daylight / Warm white compact fluorescent lamp No 26.00

PL 18W

(Philip, Splendour, Osram, Sylvania)

416 Daylight / Warm white compact fluorescent lamp No 27.00

PLC 26W

(Philip, Splendour, Osram, Sylvania)

417 ' PHILIPS ' BPL 10 L23 ballast for compact fluorescent lamp No 11.10

(Ozon, Splendour, Osram, Sylvania)

418 ' PHILIPS ' TCS 058 / 118 fluorescent luminaire c/w No 91.00

1 x 18W TLD lamp, low loss ballast in HPF switch start

circuitry and opal diffuser

419 ' PHILIPS ' TCS 058 / 236 fluorescent luminaire c/w No 155.00

2 x 36W TLD lamp, low loss ballast in HPF switch start

circuitry and opal diffuser

420 Arcluce Monos' 1021, 1 x 36W (IP40) oval-shaped, No 151.80

extruded aluminium tubular system c/w reeded

prismatic diffuser

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 33: Electrical SOR

SOR 33SCHEDULE OF RATES

Item Description Unit Rate ($)

421 'PHILIPS' Sox 18w low pressure sodium lamp No 59.20

(Osram, Sylvania)

422 250-500W double-ended tungsten 119mm No 14.00

halogen lamp 240V R75

( Osram, Splendour, Philip, GE )

423 'PHILIPS' MHN-TD 250W double-ended metal No 178.50

halide lamp

(Ozon, Splendour, Sylvania)

424 ' AMCOL ' AFR /M24 /236 recessed fluorescent fittings No 77.60

c/w ATCO LEC 40 EO low losss ballasts & KSH 12 (C12)

clear flat acrylic prismatic diffusers c/w 2 x 36W tubes

425 ' AMCOL ' AFR /M22 /218 recessed fluorescent fittings No 57.40

c/w ATCO LEC 20 EO low losss ballasts & KSH 12 (C12)

clear flat acrylic prismatic diffusers c/w 2 x 18W tubes

426 'AMCOL ' C12 1200mm x 600mm clear flat prismatic No 14.80

diffuser only

427 'AMCOL' AND 140 fluorescent fittings c/w ATCO EC No 38.00

low loss ballast and clear flat acrylic prismatic diffusers

c/w 1 x 36W tube

428 'AMCOL' AND 120 fluorescent fittings c/w ATCO EC No 32.00

low loss ballast and clear flat acrylic prismatic diffusers

c/w 1 x 18W tube

429 'GEC' dd 120 flourescent luminaires and low loss ballast, No 32.00

diokon diffuser c/w 1 x 18W tube

430 Double-sided box type Emergency "EXIT" sign, wall or No 120.00

ceiling mounted c/w 2 x 8W tube and Nickel Cadmium

battery pack

431 Single-sided box type Emergency "EXIT" sign, wall or No 110.00

ceiling mounted c/w 2 x 8W tube and Nickel Cadmium

battery pack

432 Double-sided slim type Emergency "EXIT" sign, wall or No 134.00

ceiling mounted c/w 2 x 8W tube and Nickel Cadmium

battery pack

433 Single-sided slim type Emergency "EXIT" sign, wall or No 134.00

ceiling mounted c/w 2 x 8W tube and Nickel Cadmium

battery pack

434 Philips FGC Security lighting including PL 9W lamp No 146.05

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 34: Electrical SOR

SOR 34SCHEDULE OF RATES

Item Description Unit Rate ($)

435 MLS / S / 2080 NC 2 hrs 'Boxer' 2 x 8W sustained No 111.50

emergency exit lights c/w 2 hours ni-cad batteries

436 MEP / NM / 208P self contained emergency lighting No 115.55

c/w 2 x 8W fluorescent lamp

437 Fluorescent tube in emergency exit signs - 8W No 3.90

438 Colour bulb 5W No 1.40

439 Colour bulb 15W / 25W No 1.60

440 Colour bulb 40W No 1.90

441 Square Polomiti ceiling luminaire c/w 2 x 9W PL lamp No 120.75

or 2 x 11W PL lamp ballast & capacitor

442 Rectangular wall luminaire c/w x 2 x 11W PL, ballast No 98.90

& capacitor

443 16W / 28W / 38W 2D lamp 4 pins No 28.00

GE, Thorn, Philip)

444 120W / 150W Par 36 lamp ' OSRAM ' No 12.00

(Philip, Thorn,Splendour, Sylvania)

445 Superclub, club / Diamond light fitting c/w No 75.00

2D 16W lamp & accessories

( Thorn or other approved)

446 Superclub, club / Diamond light fitting c/w No 90.00

2D 28 / 38W lamp & accessories

( Thorn or other approved)

447 SIMENS CAMEO No 90.00

( 2 X 9 watts PL lamp)

448 ' WE-EF ' LIGHT FITTING No 199.40

Model : DLG 259-DD-26

complete with PL-C lamp 26W

449 ' THORLUX ' light fitting No 185.00

Model : Prismalette bulkheed luminaires

Cat No. PS 7952S complete with 2D 38W / 28W lamp

or 2 x PL 11W lamp

450 Recessed downlight fitting ceiling ring diameter No 76.40

160mm complete with SL 18 lamp

451 Recessed downlight similar to "DUTCH-LITE' No 151.80

KL 7943 c/w 2 x 13W PL lamp ring diameter

225mm & silver reflector

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 35: Electrical SOR

SOR 35SCHEDULE OF RATES

Item Description Unit Rate ($)

452 Ceiling mounted fluorescent luminaire similar to No 126.50

NIBA Act No. 3688 of colour white diffuser, frame

in orange-Ped PC white base in self extinguishing

thermoplastic & external SS screws c/w 2D 28W warm

white lamp

453 Termo-Lyra TL-M0445/11 decorative ceiling light c/w No 120.75

11W PL Lamp

454 DIL-Ciko 17 recessed downlight ring diameter 185mm No 117.30

c/w 1 x 13W PLC lamp

455 RAAK recessed sownlight R14-0003 ring diameter No 312.80

190mm c/w 1 x 18 / 21W PL Lamp

456 Royce Thomson RTE / PS / KT Photorell kit No 85.70

457 32 / 40W square box light fitting 600mm x 600mm No 39.20

including the use of metal movable scaffolding if necessary

458 100W bulbs for roof top Aviation light No 2.60

459 100 watts GLS coiled coil tungsten incandescent lamp No 4.90

bulbs with ES caps for aircraft warning light

460 'BERGER & WEISER ' Model No 5203 outdoor No 52.00

corrision resistant sportlight c/w 1 x Par 38 cool beam

100W lamp and ground spike

461 Lightcraft AGT 146 / P3-2 double c/w PLC 26W Set 590.00

462 Lightcraft AGT 146 / P3-1 double c/w PLC 26W lamp Set 435.00

463 Lightcraft AGT 180 / P3-1 lantern & ballast c/w Set 365.00

PLC 26W lamp

464 Lightcraft AGT 180 / P3-1 telescopic post / 1 white Set 195.00

head post c/w holder, plastic shade and PLC 26W

465 FABRIKANT 8003 twin obstruction light, lighting control Set 1250.00

box and change over relay c/w bracket and on roof 42mm

dia. Hot dipped galvanised steel pipe mounted on roof

deck and secured by 3 Nos. stainless steel cable support

466 WE-EF 808-E2-100 Twin obstruction light c/w 8000hr Set 1250.00

Claude Kryton lamps, lighting control box and change

over relay, brackets and 43mm dia. Hot dipped galvanised

steel pipe mounted on roof deck and secured by 3 nos.

stainless steel cable support

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 36: Electrical SOR

SOR 36SCHEDULE OF RATES

Item Description Unit Rate ($)

LIGHTING CONDUCTORS, EARTH RODS AND CLAMPS

467 Lighting conductors aluminium 25mm x 3mm tape with m 7.40

aluminium clip and base properly secured onto wall or roof

with stainless steel screws (scaffolding measured

separately (Furse, Emtech, HS, Heng)

468 Lighting conductors copper 25mm x 3mm tape with M 8.40

brass/bronze clip and base

(Furse, Emtech, HS, Heng)

469 Air Terminal, taper-pointed aluminium rod, 16mm diameter No 11.00

and 300mm long, complete with aluminium air terminal

base and stainless steel screws

(Furse, Emtech, HS, Heng, NSI )

470 Air Terminal, taper-pointed copper, 16mm diameter and No 27.00

300mm long, complete with leaded gunmetal air terminal

(Furse, Emtech, HS, Heng, NSI )

471 Bi-metallic aluminium-copper connector for conductor No 28.70

tapes (Furse, BICC< Cembre, Rema, Heng, HS )

472 Earth rod 16mm diameter copper-weld rod mild steel No 109.00

3.6m long driven in ground, complete with bronze clamp,

and coupling interconnecting 25mm x 3mm copper tape

(not exceeding 5m) and galvanised hinged lid inspection pit

473 Earth rod 16mm diameter copper-weld rod mild steel No 28.70

1.8m long driven in ground, complete with bronze coupling

(Furse, Emtech, HS, Heng, NSI )

474 Labour and equipment to cocnduct testing of lighting Point 10.00

protection system (LPS) including certification of test

report by PUB licensed electrical worker

475 Aluminium square Tape Clamp suitable for 25 x 3 mm No 8.00

conductor size similar to ' Furse' or other approved

(Heng, HS, NSI)

476 Leaded Gunmental square Tape Clamp suitable for 25 x 3 mm No 13.50

conductor size similar to ' Furse' or other approved

(Heng, HS, NSI)

477 Leaded sunmetal round test clamp similar to Furse No 30.60

CT405 or other approved

478 Exothermic welded joints for 20 x 3mm copper tapes - No 22.10

cable to steel syrface similar to Furse Type BSI or BS2

or Cadweld Type CW, or other approved

479 Precase concrete cover 225mm x 225mm No 2.80

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 37: Electrical SOR

SOR 37SCHEDULE OF RATES

Item Description Unit Rate ($)

480 250 x 250 x 4 mm thick hot-dipped galvanised hinged No 27.00

lid inspection pit compete with plastic moulded pot

(Heng, HS, NSI, Sunlight)

481 Earth clip/clamp for water pipe/gas pipe bonding diameter No 3.00

12mm - 75mm c/w label

482 PUB approved earth rod to tape A type earthing clamp No 12.00

c/w label (Heng, HS, NSI)

483 Inter connecting buried 25 x 3mm copper pipe m 6.00

484 236 x 236 x 230mm polymer earth eletrode inspection pit No 33.00

485 Electrical joint compound for earthing rod cap Tube 60.00

(8 oz plastic tube type)

MISCELLANEOUS

486 Take delivery from any store, transport, cut stem as No 33.20

required and fix fan and regulator (hook not included)

487 Tinned copper busbar including fixing accessories Kg 20.00

and connection

488 Supply and fix 75mm2 earth wire tap No 8.60

489 Supply and fix approved powered drive masonry pin No 0.60

including the use of cartridges

490 Labour only taking down, removing and refixing No. 15.00

ceiling fans and regulators in new position not

exceeding 200mm distance

491 Labour only taking down, removing and refixing No 20.00

ceiling fans and regulators in new position exceeding

200mm distance including all necessary transport

492 Labour for taking down wall fan in hawker centre or Per Job 13.00

other parts of any building for cleaning, oiling, servicing

& refixing after work completion

493 Labour only for refixing loose and fallen teak battens m 1.20

including replacement of wall plugs where necessary

(where work involved in this item does not exceed 10m,

a minimum charge of 10m applies)

494 Labour only for refixing loose lighting conductors m 2.40

including replacement of wood plugs and staples

(where work involved in this item does not exceed 10m,

a minimum charge of 10m applies)

(Scaffolding measured separately)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 38: Electrical SOR

SOR 38SCHEDULE OF RATES

Item Description Unit Rate ($)

495 Labour only for refixing loose and fallen wirinng m 1.20

including supply of additonal saddles or clips

(where work involved in this item does not exceed 10m,

a minimum charge of 10m applies)

(Scaffolding measured separately)

496 Hacking existing rc slab not exceeding 225mm thick to form opening 9.00

opening 150mm x 75mm for trunking including making

good all works disturbed and to match existing with paint

497 Patch up openings for pipes / conduit exceeding 100mm dia No 5.00

but not exceedidng 225mm dia. With cement and sand (1:3)

including approved waterproof compounds in wall and

floor not exceeding 225mm thick and make good to match

existing

498 Labour only for refixing loose or fallen ceiling blocks / wood No 1.20

blocks including the replacement of wood plugs

where necessary

499 Labour only fr refixing meter / distribution boards No 11.70

including the replacment of wood plug where necessary

500 Labour only for refixing loose electrical fittings and No 6.00

accessories including the replacment of wood plugs where

necessary / labour to convert ceiling rose of light fitting

to cable & PVC trunking including all necessary parts

& fitting for the connection work

501 Refix loose galvanised steel conduit 20mm diameter Per Job 10.50

pipes at gable end wall including new hasp clip, saddle

clams and screws

502 Labour to check and tighten the loose cable connection Per Job 20.00

for fuses, MCCB's and busbars in the main switchboard

503 Labour only for removing unauthorised wirings, battens, Per Job 15.00

in vacant flat, touch up all plug holes with putty and all

affected work to match existing with paint

504 Erection of double layer timber scaffolding including m2 4.20

taking down after use (irrespective of height of building,

a minimum of 5m shall be paid)

505 Erection of metal scaffolding not exceeding 15m height m2 10.90

including taking down after use

506 Erection of metal scaffolding exceeding 15m height but m2 12.10

not exceeding 35m height including taking down after use

507 Supply and fix 150 x 180 x 70 mm approved metal box with No 26.00

cam lock and hidden hinges to wall for 13 Amp socket

outlet (measure separately)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 39: Electrical SOR

SOR 39SCHEDULE OF RATES

Item Description Unit Rate ($)

508 Labour only for checking and attending to defective Per Job 30.00

light in community hall and other parts of building

exceeding 8m height inclcuding use of movable metal

scaffolding (parts and fittings will be paid separately)

509 GS bracket for metal trunking fixed to ceiling or wall No 3.80

including ramset nails and 2 coats of painting

510 Supply and fix 125W or 250W procelain lamp holder No 18.10

inclcuding use of movable metal scaffolding

511 Supply and fix 150/200W spot light fitting complete with No 33.30

base holder to wall or ceiling and including making

good all work disturbed

512 Padlock for public fitting 'Yale' 713 / 40mm or other approved No 6.00

513 Supply and install safety rubber mats M.R 52.00

Size : 900mm width x 6.5mm thick

514 Supply and install 60A TPN tap-off box c/w fuse 'CIAMA' No 400.00

515 Wire-guard warning light for pump room No 50.00

516 Labour and material only for modifying the existing No 6.00

fluorescent light fitting for installation of electronic or

low loss ballast including supply of necessary wiring

517 Supply and fix PUB's approved first aid chart in switchroom No 20.00

518 Labour tocheck, clean and tighten the 1st 5 nos. of loose No 4.00

neutral connector or line tap/line connector including

replacement of defective screws (within same block)

519 Labour tocheck, clean and tighten the remaining nos. of No 2.00

loose neutral connector or line tap/line connector including

replacement of defective screws (within same block)

The following accessories and fittings include all

necessary fixing screws, wood plugs etc.

520 350mm x 200mm x 170mm metal box with 165mm x 200mm x No 118.40

15mm metal mounting plates, welded internally an centrally

to base of metal box fabricated from 1.2mm thich

electro-galvanised sheet steel c/w hidden door hinges,

waterproofing seals, 2 nos. 6mm dia steel thumb screw

with plastic knobs, earth terminal and treated with paint

finish of 45 microns oven baked and dried.

(For 30 Amp MCCB)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 40: Electrical SOR

SOR 40SCHEDULE OF RATES

Item Description Unit Rate ($)

521 Supply, deliver and install metal box fabricated from m2 375.00

1.6mmthick, electro-galvanised sheet steel complete with

hidden door hinges, water-proofing seals, lock facilities,

treated with paint finish of 45 microns overbaked & dried

(overall 260mm thickness)

522 Supply, deliver and install metal box fabricated from m2 400.00

1.6mmthick, electro-galvanised sheet steel complete with

hidden door hinges, weather proofing seals, lock facilities,

treated with paint finish of 45 microns overbaked & dried

(overall 300mm thickness)

523 Supply, deliver and install metal box fabricated from m2 435.00

1.6mmthick, electro-galvanised sheet steel complete with

hidden door hinges, weather proofing seals, lock facilities,

treated with paint finish of 45 microns overbaked & dried

(overall 350mm thickness)

524 Supply, deliver and install metal box fabricated from m2 498.00

1.6mmthick, electro-galvanised sheet steel complete with

hidden door hinges, weather proofing seals, lock facilities,

treated with paint finish of 45 microns overbaked & dried

(overall 400mm thickness)

525 Labour for checking firmness of ceiling fan bracket/hook, Per Fan 15.00

taking down ceiling fans in hawker centres or other

buildings as directed, dismantling the mechanical

connecting components to check for worn bolt / rivets,

corroded hanging rod and bolt assembly without split

cotter pins and replacing these parts (parts measured

separately ) if necessary, including cleaning fans and

refixing on completion

526 Labour nly for dismantling and re-fixing the illuminated No 35.00

Block No. / Carpark Signages for the purpose of carrying

out the repair / replacement of defective fluorescent

tubes, starters, ballasts etc inclusive of metal scaffoldings

not exceeding 6.5m height ( Parts and fittings shall be

measured separately )

527 Labour nly for dismantling and re-fixing the illuminated No 45.00

Block No. / Carpark Signages for the purpose of carrying

out the repair / replacement of defective fluorescent

tubes, starters, ballasts etc inclusive of metal scaffoldings

exceeding 6.5m height but ecceeding 15m height.

( parts and fittings shall be measured separately )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 41: Electrical SOR

SOR 41SCHEDULE OF RATES

Item Description Unit Rate ($)

528 Supply and fix stainless steel screw ( cylindrical head ) No 4.40

with washer to electro galvanised steel tap off box/s cover

inclcuding labout for drilling holes, forming screw thread

and opening defective cam lock

529 Servicing of switchroom, switchboards panel, including Per Rm 300.00

cleaning and vacuum cleaning of air circuit breaker, MCCB,

MCB, tightening of contact point, terminal busbar, testing

and reset to normal after work completed and remove all

rubbish from site

530 Supply and isntall A1 size wooden framing for single No 50.00

line diagram in switchroom

DAYWORK

The following daywork's Schedule of Rates are without

establishment charges abd profit. The 15% establishment

cahrges abd profit for items Nos. 531 to 537 shall be

payable to the contractor

The percentage adjustment to the Standard Schedule of

Rates as inserted in the Form of Tender in this contract

shall apply to them No.531 532 only.

In the case of building fair rates (star rates) the Daywork

rates shall not be subjected to the percentage adjustment

to the Standard Schedule of Rates as inserted in the Form

of Tender. However the 15% establishment charges and

profit is payable.

The following rates shall be applicable in respect of all

work executed on a daywork basis. During the continuance

of such work, the contractor shall keep proper records

of such work, the contractor shall keep proper records

of the names, occupations and working hours of all

workmen employed for such work and the quantities and

and descriptions of all materials and plant employed.

Such records, receipts or vouchers must be verified by

the Superintending Officer's representative before

payment can be effected . Provided always if the

Superintending Officer's representative shall consider

that for any reason the keeping of records, receipts and

vouchers by the contractor as required was impracticable,

he shall nevertheless be entitled to authorise payment

for such work either as daywork (on being satisfied as to

the time employed and plant and materials used on such

work) or at such value thereof as he shall considered

fair and reasonable.

Provide the undermentioned labour as may be ordered in

writing by the Superintending Officer

531 Supply of labourer for miscellaneous work Per Hour 4.70

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 42: Electrical SOR

SOR 42SCHEDULE OF RATES

Item Description Unit Rate ($)

532 Supply of skilled electrician Per Hour 7.00

533 Services rendered by skilled electriician for resetting of Per Hour 9.00

MCCB / earth fault relay / overcurrent electrical faults

( after officer hours or on Saturday, Sunday and Public

Holidays) for a minimum of 4 hours

534 Services rendered by licensed electrical worker of Per Hour 30.00

technician grade for a minimum of 1.5 hours during office

hours 8.00 am to 5.30 pm

535 Services rendered by licensed cable detection worker Per Hour 115.00

for site excavation using mechanical means for laying of

underground cables / erection of lighting columns for

a minimum of 1 1/2hours

536 Services rendered by licensed electrical engineer Per Hour 50.00

for a minimum of 1 1/2 horus ( during office hours

8.00 am to 5.30 pm )

537 Services rendered by licensed electrical engineer Per Hour 75.00

for a minimum of 1 1/2 horus ( after office hours or on

Saturday, Sunday and public holiday )

538 Injection test for 1 No. ACB / MCCB ( with earth fault / No 850.00

overcurrent protections ) by PSPL / PGPL registered testing

engineer including submission of shutdown form to

PSPL / PGPL, arrangement for shutdown etc for testing

and providing temporary electrical supply and skilled

electricians, equipment and transportation cost -

during office hours i.e 8.00 am to 5.30 pm

539 Injection test for each additional circuit breaker ( with No 600.00

earth fault / overcurrent protections ) within the same

switchroom as item 538

540 Injection test for 1 No. ACB / MCCB ( with earth fault / No 1200.00

overcurrent protections ) PSPL / PGPL registered testing

engineer including submission of shutdown form to

PSPL / PGPL, arrangement for shutdown etc for testing

and providing temporary electrical supply and skilled

electricians, equipment and transportation cost - after

office hours or on Saturday, Sunday and Public Holiday

541 Injection test for each additional circuit breaker No 850.00

( with earth fault / overcurrent protections) within the same

switchroom as item 540

542 Application and endorsement of PSPL Form CS / 1 as Per Job 150.00

licensed electrical worker when requested by

Superintending Officer for PSPL testing for electrical

extension / minor rewiring work for non licensed electrical

isntallation

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 43: Electrical SOR

SOR 43SCHEDULE OF RATES

Item Description Unit Rate ($)

543 Servicing of air-circuit breaker (ACB) including provision No 550.00

of labour for the work - during officer hour i.e 8.00 am

to 5.30 pm

544 Servicing of additional air-circuit breaker within the No 450.00

same switchroom as item 543

545 Servicing of air-circuit breaker ( ACB ) including provision No 900.00

of labour for the works - after officer hour or on Saturday,

Sunday and Public Holiday

546 Servicing of air-circuit breaker ( ACB ) including provision No 1100.00

of generator for work carry out during mid-night

547 Servicing additional air-circuit breaker ( ACB ) within No 850.00

same switchroom including provision of labour for the

work - after office hours or on Saturday

548 Servicing additional air-circuit breaker ( ACB ) within the No 1000.00

same switchroom including provision of generator for

work carry out during mid-night

549 Supply of PUB Licensed Cable Jointer to carry out Per Job 150.00

"Live" termination of CTS cabales at OG bet

550 Supply of PUB authoirsed small installation tester (ASIT) Per Job 100.00

to test electrical extensions and submission of report to

PUB / Town Council

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 44: Electrical SOR

SOR 44SCHEDULE OF RATES

Item Description Unit Rate ($)

EXCAVATION AND BACKFILLING

551 Excavate trench 300 x 750 mm deep by hand, sand bed m 3.90

and backfilling as specified for cable (s) in trench

552 Excavate trench 300 x 750 mm deep by excavator, sand m 3.00

bed and backfilling as specified for cable (s) in trench

553 Excavate pit 1m x 1m x 750mm deep and backfilling No 27.00

554 Supply and turf good quality 25mm thick cow grass close m2 4.00

turfing including 125mm thick top soil and well watering

and tendering to ensure growth of turfs.

CABLE GLANDS TO BS 6121:1973

555 Supply and install brass compression glands ( Type BW) No 9.90

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 6mm2 2 core

PVC / SWA / PVC cables

556 Supply and install brass compression glands ( Type BW) No 11.60

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 10mm2 2 core

PVC / SWA / PVC cables

557 Supply and install brass compression glands ( Type BW) No 12.20

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 16mm2 2 core

PVC / SWA / PVC cables

558 Supply and install brass compression glands ( Type BW) No 12.20

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 25mm2 2 core

PVC / SWA / PVC cables

559 Supply and install brass compression glands ( Type BW) No 18.40

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 50mm2 2 core

PVC / SWA / PVC cables

560 Supply and install brass compression glands ( Type BW) No 10.50

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 6mm2 4 core

PVC / SWA / PVC cables

561 Supply and install brass compression glands ( Type BW) No 12.40

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 10mm2 4 core

PVC / SWA / PVC cables

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 45: Electrical SOR

SOR 45SCHEDULE OF RATES

Item Description Unit Rate ($)

562 Supply and install brass compression glands ( Type BW) No 15.10

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 16mm2 4 core

PVC / SWA / PVC cables

563 Supply and install brass compression glands ( Type BW) No 18.00

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 25mm2 4 core

PVC / SWA / PVC cables

564 Supply and install brass compression glands ( Type BW) No 19.10

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 35mm2 4 core

PVC / SWA / PVC cables

565 Supply and install brass compression glands ( Type BW) No 20.30

including brass locknut, earth tags, shroud, connection

to cable and mounting bracket for 50mm2 4 core

PVC / SWA / PVC cables

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 46: Electrical SOR

SOR 46SCHEDULE OF RATES

Item Description Unit Rate ($)

JOINTS

566 Underground straight cable joints of PVC/SWA/PVC No 44.30

cables of all sizes ( 2 x 6 / 10 /16 mm2 and 4 x 6 / 10 /6 mm2 )

567 Underground straight cable joints of PVC/SWA/PVC No 62.70

cables of all sizes ( 2 x 25 / 50 mm2 and 4 x 25 / 50 mm2 )

568 Underground Tee-joints of PVC/SWA/PVC cable of No 56.90

all sizes ( 2 core x 6 mm2 to 2 core x 25 mm2 inclusive )

569 Wiring of 2 x 6 mm2 PVC covered overhead line conductors m 1.30

of hard-drawn copper on insulators without intermediate

support ( SCM, Sigma, Wilson, Unicable)

570 Wiring of 2 x 10 mm2 PVC covered overhead line conductors m 2.00

of hard-drawn copper on insulators without intermediate

support ( SCM, Sigma, Wilson )

571 Wiring of 2 x 16 mm2 PVC covered overhead line conductors m 2.90

of hard-drawn copper on insulators without intermediate

support ( SCM, Sigma, Wilson )

572 Wiring of 2 x 25 mm2 PVC covered overhead line conductors m 4.30

of hard-drawn copper on insulators without intermediate

support ( SCM, Sigma, Wilson )

573 Wiring of 2 x 6 mm2 PVC insulated and sheathed cable on m 1.70

insulators supported by and including a caternary wire

( SCM, Sigma, Wilson )

574 Wiring of 2 x 10 mm2 PVC insulated and sheathed cable on m 2.50

insulators supported by and including a caternary wire

( SCM, Sigma, Wilson )

575 Wiring of 2 x 16 mm2 PVC insulated and sheathed cable on m 3.40

insulators supported by and including a caternary wire

( SCM, Sigma, Wilson )

576 Wiring of 2 x 25 mm2 PVC insulated and sheathed cable on m 4.80

insulators supported by and including a caternary wire

( SCM, Sigma, Wilson )

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 47: Electrical SOR

SOR 47SCHEDULE OF RATES

Item Description Unit Rate ($)

CATENARY WIRE AND INSULATORS

577 Supply and fix catenary wire between lamp posts to m 0.70

support cables

578 Supply and fix porcelain insulator No 22.50

LIGHTING DISTRIBUTION BOARD, FUSES,

TIME SWITCHES, ETC

* Supply and fix the following accessories including all

necessary fixing screws, rawl plugs etc * ( 579 - 598)

579 Street lighting cut-outs 25 Amps, 240 Volts No 40.00

BICC Cat No. G72515-02 ( 1 tag type )

or other approved type

580 Street lighting cut-outs 25 Amps, 240 Volts No 45.00

BICC Cat No. G72515-06 ( 2 tag type )

or other approved type

581 ' BICC ' Cat No. G72522-03 or other approved cable with No 35.00

glandplate and wormdrive clips for attaching to street

lighting cutout

582 ' BICC ' Cat No. G72569-02 or other approved 3 phase No 56.00

adaptor with bottom plate for attaching to street

lighting cutout

583 Lighting distribution with metal enclosure comprising No 596.40

the following :

1 No. 20A 250V ' Horstmann' Type Y Quartz Time Switch

or other approved type with 150 hours battery reserve

4 No. 20Amp HRC fuse, fuse carrier and holder (PHL,

Merlin Gerin, Mem)

1 No. 30A D.P. MCB (22KA) and

1 No. 100MA 40A D.P. ELCB

( Hatachi, Merlin Gerin, Nikko)

1 No. 30A T.P Contactor

( Hitachi, Mitsubishi, Stromberg )

1 No. 30/60A 'by-pass' switch and all internal wiring

and connection

584 20 - 30 Amp HRC fuse, fuse carrier and holder No 13.20

( English Electric, Legrand, Mem )

585 60 Amp bakelite insulated connector similar to No 7.70

Lucy Cat No. MLN or approved equivalent

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 48: Electrical SOR

SOR 48SCHEDULE OF RATES

Item Description Unit Rate ($)

586 300 x 100 x 25 timber teak board No 4.00

587 300 x 230 x 25 timber teak board No 10.00

588 520 x 230 x 25 timber teak board No 16.50

( meterboard )

589 330 x 700 x 25 timber teak board No 18.00

590 450 x 600 x 25 timber teak board No 18.00

591 2 way earth terminal No 1.30

592 3 way earth terminal No 1.70

593 4 way earth terminal No 1.90

594 2 x 6 mm2 PVC/PVC c/w 6mm2 PVC E m 4.60

Jumper cable between main switch board and

underground cables terminations including necessary

jointing, connectors

595 2 x 10 mm2 PVC/PVC c/w 10mm2 PVC E m 5.60

Jumper cable between main switch board and

underground cables terminations including necessary

jointing, connectors

596 2 x 16 mm2 PVC/PVC c/w 16mm2 PVC E m 6.80

Jumper cable between main switch board and

underground cables terminations including necessary

jointing, connectors

597 2 x 25 mm2 PVC/PVC c/w 16mm2 PVC E m 8.80

Jumper cable between main switch board and

underground cables terminations including necessary

jointing, connectors

598 2 x 50 mm2 PVC/PVC c/w 25mm2 PVC E m 11.20

Jumper cable between main switch board and

underground cables terminations including necessary

jointing, connectors

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 49: Electrical SOR

SOR 49SCHEDULE OF RATES

Item Description Unit Rate ($)

SURFACE WIRING IN G.I CONDUIT/METAL TRUNKINGS

* Supply and fix the following including all necessary

screw, rawl plug, stades/clips and bracket etc * ( 599 to 605)

599 Interconnecting wiring in 2 x 6 mm2 PVC/PVC complete m 11.00

with 6 mm2 PVC (green) earth wiring ( between main

switch board and lighting distribution board including

necessary terminations, lugs and conduit/metal trunking)

600 Interconnecting wiring in 2 x 10 mm2 PVC/PVC complete m 11.80

with 10 mm2 PVC (green) earth wiring ( between main

switch board and lighting distribution board including

necessary terminations, lugs and conduit/metal trunking)

601 Interconnecting wiring in 2 x 16 mm2 PVC/PVC complete m 13.60

with 16 mm2 PVC (green) earth wiring ( between main

switch board and lighting distribution board including

necessary terminations, lugs and conduit/metal trunking)

602 Interconnecting wiring in 2 x 25 mm2 PVC/PVC complete m 17.70

with 16 mm2 PVC (green) earth wiring ( between main

switch board and lighting distribution board including

necessary terminations, lugs and conduit/metal trunking)

603 Interconnecting wiring in 2 x 50 mm2 PVC/PVC complete m 21.00

with 25 mm2 PVC (green) earth wiring ( between main

switch board and lighting distribution board including

necessary terminations, lugs and conduit/metal trunking)

604 Interconnecting wiring in 4 x 6 mm2 PVC/PVC complete m 13.80

with 6 mm2 PVC (green) earth wiring ( between main

switch board and lighting distribution board including

necessary terminations, lugs and conduit/metal trunking)

605 Interconnecting wiring in 4 x 25 mm2 PVC/PVC complete m 22.70

with 16 mm2 PVC (green) earth wiring ( between main

switch board and lighting distribution board including

necessary terminations, lugs and conduit/metal trunking)

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 50: Electrical SOR

SOR 50SCHEDULE OF RATES

Item Description Unit Rate ($)

POST TOP LANTERNS

606 Labour to remove existing post top lantern including No 10.80

reinstatement of surfaces, transportation and disposal

of post top lantern off site

607 Removal of post top lantern including excavation, taking No 48.50

off of poles, concrete foundation, backfilling, reinstatement

of ground surfaces, transportation and disposal of surplus

earth and post top lantern off site

* Supply, deliver to site and install the following

including connecting wiring, mounting brackets, screws,

connections. ( Labour to remove existing post top lantern

to be measured separately) * ( 608 695)

608 ' INDALUX ' post top polycarborate clear diffuser No 499.00

lantern cat no 250-IJB-RK complete with 80E / 125W

HPL-N lamp and intergral control gear

609 ' INDALUX ' post top polycarborate clear diffuser No 520.00

lantern cat no 250-IJB-RK complete with 70W / 50W

SON lamp and intergral control gear

610 ' INDALUX ' post top polycarborate cleardouble No 635.00

prismatic diffuser lantern cat no. 250-IJD-RK complete

with 80W/125W HPL-N lamp and intergral control gear

611 ' INDALUX ' post top polycarborate cleardouble No 665.00

prismatic diffuser lantern cat no. 250-IJD-RK complete

with 70W/50W SON lamp and intergral control gear

612 ' INDALUX ' QUEBEC 125-IQC' post top lantern c/w No 600.00

aluminium canopy, intergral control gear, polycarbonate

frosted sphere and 1 x 125W / 80W mercury vapour lamp

613 ' INDALUX ' QUEBEC 125-IQC' post top lantern c/w No 680.00

aluminium canopy, intergral control gear, polycarbonate

frosted sphere and 1 x 70W SON lamp

614 ' INDALUX ' QUEBEC 150-IQC' post top lantern c/w No 690.00

aluminium canopy, intergral control gear, polycarbonate

frosted sphere and 1 x 70W SON lamp

615 ' INDALUX ' post top lantern model IJK c/w 125W HPL No 533.60

lamp and integral control gear

616 THORN-JOHANNA QGJ 1070-4 post top lantern c/w No 453.00

integral control gear and 1 x 70W SON lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 51: Electrical SOR

SOR 51SCHEDULE OF RATES

Item Description Unit Rate ($)

617 'PGL' post top polycarborate opal 400 mm diameter No 256.00

spherical lantern cat no. P/4C c/w 80W / 125W HP-N lamp

and integral control gear

618 'PGL' post top polycarborate clear / smoke 400 mm diameter No 295.00

spherical lantern cat no. P/4C c/w 80W / 125W HP-N lamp

and integral control gear

619 'PGL' post top polycarborate opal 400 mm diameter No 295.00

spherical lantern cat no. P/4C c/w 70W SON lamp

and control gear

620 'PGL' post top polycarborate clear / smoke 400 mm diameter No 352.00

spherical lantern cat no. P/4C c/w 70W son lamp

and integral control gear

621 'PGL' post top polycarborate 500 X 500 mm clear/smoke No 398.00

lantern cat no. P/ 5 x 5C c/w 80W / 125W HPL-N lamp

and integral control gear

622 'PGL' post top polycarborate 500 X 500 mm clear / smoke No 440.00

lantern cat no. P / 5 x 5C c/w 70W SON lamp

and integral control gear

623 'PGL' post top polycarborate 400 X 500 mm cylinder No 441.00

clear / smoke lantern cat no. P / 4 x 5C c/w 80W / 125W

HPL-N lamp and integral control gear

624 'PGL' post top polycarborate 400 X 500 mm cylinder No 389.00

clear / smoke lantern cat no. P / 4 x 5C c/w 70W

lamp and integral control gear

625 'PGL' louvre for post top lantern No 115.10

626 ' RAAK' Elipse post top lantern cat no. s-2389.1321 No 608.00

complete with 70W SON lamp and integral control gear

627 ' RAAK' post top kosmos 430 mm diameter Lantern No 698.80

cat no. S2280 . 8000 complete with 80W HPL-N lamp

and integral control gear

628 ' RAAK' post top kosmos 430 mm diameter Lantern No 790.80

cat no. S2280 . 7000 complete with 70W HPL-N lamp

and integral control gear

629 ' RAAK' octahedron S - 2387 . 1321 complete with No 956.46

70W SON lamp and integral control gear

630 ' Philips ' post top Lantern cat no. HPP 131, opal - white No 337.00

sphere with black rim, complete with 80W HPL - N lamp

and integral control gear

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 52: Electrical SOR

SOR 52SCHEDULE OF RATES

Item Description Unit Rate ($)

631 ' Philips ' post top Lantern cat no. HPP 131, opal - white No 337.00

sphere with black rim, complete with 125W HPL - N lamp

and integral control gear

632 ' Philips ' post top Lantern cat no. SPP 131, opal - white No 298.00

sphere with black rim, complete with 70W SON lamp

and integral control gear

633 'Philips' lighting luminaire comprising of opal-white No 330.50

sphere, complete with 80W or 125W lamp and integral

control gear

634 'Philips' lighting luminaire comprising of opal-white No 351.20

sphere, complete with 70W SON lamp and integral

control gear cat SPP 133

635 'Philips' post top lantern cat no. HPP 134, opal-white No 303.00

elipse, complete with 80W HPL-N lamp and integral

control gear

636 'Philips' post top lantern cat no. HPP 134, opal-white No 309.00

elipse, complete with 125W HPLN lamp and integral

control gear

637 'Philips' post top lantern cat no. SPP 134, opal-white No 323.00

elipse, complete with 70W SON lamp and integral

control gear

638 'Philips' post top lantern cat no. HPP 136, opal-white No 294.00

cone, complete with 80W HPL-N lamp and integral

control gear

639 'Philips' post top lantern cat no. HPP 136, opal-white No 297.00

cone, complete with 125W HPL-N lamp and integral

control gear

640 'Philips' post top lantern cat no. SPP 136, opal-white No 303.00

cone, complete with 70W SON lamp and integral

control gear

641 'Philips' post top lantern cat no. HPP 137, mushroom, No 350.00

complete with 80W HPL-N lamp and integral

control gear

642 'Philips' post top lantern cat no. HPP 137, mushroom, No 352.00

complete with 125W HPL-N lamp and integral

control gear

643 'Philips' post top lantern cat no. SPP 137, mushroom, No 352.00

complete with 70W SON lamp and integral control gear

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 53: Electrical SOR

SOR 53SCHEDULE OF RATES

Item Description Unit Rate ($)

644 'Philips' lighting luminaire comprising of frosted No 397.80

polycarbonate sphere, complete with 80W or 125W HPL-N

lamp and integral control gear cat HPP 133 PCT

645 'Philips' lighting luminaire comprising of frosted No 418.50

polycarbonate sphere, complete with 70W SON lamp

and integral control gear cat SPP 133 PCT

646 'Philips' parklight Lantern cat no. GV 64 PC complete No 433.00

with 80W HPL-N lamp and control gear

647 'Philips' parklight Lantern cat no. GV 64 PC complete No 456.00

with 70W SON lamp and control gear

648 'Mazda' ' CYCAR' 400 Opal M80 / S70 post-top lantern c/w No 325.00

integral control gear and 1 x 80W HPL-N / 70W SON lamp

649 'Mazda' ' TAKEO' M80 / S70 post-top lantern with No 380.00

circular overlapping canopy complete with 80W HPL-N

lamp or 70W SON lamp and integral control gear

650 'Mazda' ' OPALA ' M80 / 'opala' S70 post-top lantern No 296.00

IP 549 c/w 400mm diameter polycarbonate diffuser and

1 x 80W HPL-N / 70W SON lamp

651 'Mazda' Agate S70 / M80 / 'opala' S70 post-top lantern No 405.00

IP 549 c/w 500mm diameter oroglass diffuser, inegral

control gear & 80W HPL-N or 70W SON lamp

652 'ERNST ' 381006 post top lantern c/w 125W mercury No 859.05

vapour lamp and inegral control gear

653 'ERNST ' 370104 post top lantern c/w 125W mercury No 801.55

vapour lamp and inegral control gear

654 'PILOTINE ' post top lantern c / w 125W mercury No 410.55

vapour lamp and integral control gear

655 'STEMTER FRANFLYN III ' post top lantern No 1396.10

cat No. FK20-10-3-N c / w 125W mercury delux lamp

and integral control gear

656 WE-EF SK409-E-80 / MV [ K ] 400mm dia spherical opal No 310.00

Polyethylene luminaire c/w corrosion resistant die-cast

aluminium alloy base, heat shield, control gear and

80 watts mercury lamp

657 WE-EF SK409-E-125 / MV [ K ] 400mm dia spherical opal No 295.00

Polyethylene luminaire c/w corrosion resistant die-cast

aluminium alloy base, heat shield, control gear and

125 watts mercury lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 54: Electrical SOR

SOR 54SCHEDULE OF RATES

Item Description Unit Rate ($)

658 WE-EF SK409-E-70 / NI [ K ] 400mm dia spherical opal No 350.00

Polyethylene luminaire c/w corrosion resistant die-cast

aluminium alloy base, heat shield, control gear and

70 watts mercury lamp

659 WE-EF SK459-E-80 / MV [ K ] 450mm dia spherical opal No 385.00

Polyethylene luminaire c/w corrosion resistant die-cast

aluminium alloy base, heat shield, control gear and

80 watts mercury lamp

660 WE-EF SK459-E-125 / MV [ K ] 450mm dia spherical opal No 448.00

Polyethylene luminaire c/w corrosion resistant die-cast

aluminium alloy base, heat shield, control gear and

125 watts mercury lamp

661 WE-EF SK459-E-70 / NI [ K ] 450mm dia spherical opal No 385.00

Polyethylene luminaire c/w corrosion resistant die-cast

aluminium alloy base, heat shield, control gear and

70 watts sodium lamp

662 WE-EF SKF450-E-80 / MV [ K ] 450mm dia Frosted or Clear No 453.00

Polycarbonate spherical luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control gear

and 80 watts mercury lamp

663 WE-EF SKF450-E-125 / MV [ K ] 450mm dia Frosted or Clear No 465.00

Polycarbonate spherical luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control gear

and 80 watts mercury lamp

664 WE-EF SKF450-E-125 / MV [ K ] 450mm dia Frosted or Clear No 504.00

Polycarbonate spherical luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control gear

and 70 watts mercury lamp

665 WE-EF SKG509-E-80 / MV [ K ] 500mm dia Decorative No 455.00

spherical opal Polyethylene luminaire c/w die-cast

aluminium base, decorative black enamelled aluminium

' basket ' , control gear and 80 watts mercury lamp

666 WE-EF SKG509-E-125 / MV [ K ] 500mm dia Decorative No 458.00

spherical opal Polyethylene luminaire c/w die-cast

aluminium base, decorative black enamelled aluminium

' basket ' , control gear and 125 watts mercury lamp

667 WE-EF SKG509-E-70 / NI [ K ] 500mm dia Decorative No 490.00

spherical opal Polyethylene luminaire c/w die-cast

aluminium base, decorative black enamelled aluminium

' basket ' , control gear and 70 watts mercury lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 55: Electrical SOR

SOR 55SCHEDULE OF RATES

Item Description Unit Rate ($)

668 WE-EF MA 11B-E-70 / NI [ K ] Post top lantern with No 474.00

'lift-off ' canopy and diffuser. Corrosion resistant

die-cast aluminium alloy base and canopy, opal diffusing

cone in vandal resistant UV stabilized high density

Polyethylene ( HDPE-S ) and complete with control gear

and 70 watts sodium lamp

669 WE-EF MA 30-E-70 / NI [ K ] Post top lantern with No 516.00

corrosion resistant die-cast aluminium alloy base and

canopy, opal diffusing cone in vandal resistant UV

stabilized high density Polyethylene ( HDPE-S ) or clear

frosted acrylic diffuser and complete with control gear

and 70 watts sodium lamp

670 WE-EF SKL 400-E-70 / MV [ K ] 400mm dia spherical No 450.00

Clear Polycarbonate luminaire c/w corrosion resistant

die-cast aluminium alloy base, anodized high purity

aluminium relfectors, built-in control gear and 80 watts

mercury lamp

671 WE-EF SKL 400-E-125 / MV [ K ] 400mm dia spherical No 462.00

Clear Polycarbonate luminaire c/w corrosion resistant

die-cast aluminium alloy base, anodized high purity

aluminium relfectors, built-in control gear and 125 watts

mercury lamp

672 WE-EF SKL 400-E-70 / NI [ K ] 400mm dia spherical No 365.00

Clear Polycarbonate luminaire c/w corrosion resistant

die-cast aluminium alloy base, anodized high purity

aluminium relfectors, built-in control gear and 70 watts

mercury lamp

673 WE-EF ZA 600-E-70 / NI [ K ] Decorative post top No 950.00

c/w corrosion resistant die-cast aluminium alloy body

and canopy, diffuser of UV stabilized and vandal resistant

Polycarbonate, anodized high purity aluminium reflector,

built-in control gear and 70 watts sodium lamp

674 WE-EF AL 500-E-70 / NI [ K ] Decorative post top No 780.00

c/w corrosion resistant die-cast aluminium alloy body ,

diffuser of UV stabilized and vandal resistant

Polycarbonate, anodized high purity aluminium reflector,

built-in control gear and 70 watts sodium lamp

675 WE-EF ASP 504-E-70 / NI [ K ] Decorative pendent No 780.00

mounted lantern c/w corrosion resistant die-cast aluminium

alloy body, diffuser of UV stabilized and Polycarbonate

lear-Patterned equipped with glare restriction and light

control reflectors, built-in control gear and 70 watts

sodium lamp and c/w pole bracket

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 56: Electrical SOR

SOR 56SCHEDULE OF RATES

Item Description Unit Rate ($)

676 Supply of WE-EF SK post top 400mm dia polyethylene No 160.00

opal white sphere

677 Supply of WE-EF post top 400mm dia polyethylene No 180.00

clearopal white sphere

678 Supply of WE-EF die-cast aluminium alloy base, heat No 180.00

shield, control gear and lamp

679 Supply of WE-EF SK post top 450 mm dia No 195.00

polyethylene opal white sphere

680 Supply of WE-EF post top 450 mm dia polyethylene No 310.00

frosted/clear sphere

681 WE-EF SKG 50 Decorative spherical opal No 506.00

polyethylene luminaire with corrosion-resistant

die-cast aluminium base, decorative black enamelled

aluminium 'basket' c/w control gear and lamp and

heat-shield SKG 50-1 / 70N diameter 500 mm

(for sodium 70W)

682 WE-EF MA 11B-E-70 / NI (K) post top lantern Set 514.00

with 'lift-off' canopy and diffuser. Corrosion-

resistant die-cast aluminium alloy base and canopy.

Opal diffusing cone in vandal resistant UV

stabilized high density Polyethylene (HDPE-S) and

complete with 70W Sodium integral control gear and

lamp

683 WE-EF MA 30-E-70 / NI (K) post top lantern with Set 543.00

corrosion-resistant die-cast aluminium alloy base

and canopy. Opal diffusing cone in vandal resistant

UV stabilized high density Polyethylene (HDPE-S)

and complete with 70W Sodium integral control

gear and lamp

684 'Siemen' Cat 5NA 5482-ICKO Post top lantern c/w No 650.00

built in 80 / 125W high pressure mercury lamp and

control gear

685 'Siemen' Cat 5NA 5482-ICKO Post top lantern c/w No 695.00

built in 50 / 70W high pressure sodium lamp and

control gear

686 FABRIKANT 4114 400mm dia spherical opal No 300.00

polyethylene luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control

gear and 80 watts mercury lamp

687 FABRIKANT 4115 400mm dia spherical opal No 308.00

polyethylene luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control

gear and 125 watts mercury lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 57: Electrical SOR

SOR 57SCHEDULE OF RATES

Item Description Unit Rate ($)

688 FABRIKANT 4116 400mm dia spherical opal No 360.00

polyethylene luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control

gear and 70 watts high pressure sodium lamp

689 FABRIKANT 4117 450mm dia spherical opal No 330.00

polyethylene luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control

gear and 80 watts mercury lamp

690 FABRIKANT 4118 450mm dia spherical opal No 340.00

polyethylene luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control

gear and 125 watts mercury lamp

691 FABRIKANT 4119 450mm dia spherical opal No 395.00

polyethylene luminaire c/w corrosion resistant

die-cast aluminium alloy base, heat shield, control

gear and 70 watts high pressure sodium lamp

692 FABRIKANT 4034 decorative post top lantern No 790.00

c/w corrosion resistant die-cast aluminium alloy body

and canopy, diffuser of UV stabilized and vandal

resistant polycarbonate, anodised high purity

aluminium reflector, built-in control gear and 70 watts

high pressure sodium lamp

693 FABRIKANT 4120 500mm dia decorative spherical No 510.00

opal polyethylene luminaire c/w die-cast aluminium

base, decorative black enamelled aluminium

"BASKET", control gear and 80 watts / 125 watt

mercury lamp

694 FABRIKANT 4121 500mm dia decorative spherical No 550.00

opal polyethylene luminaire c/w die-cast aluminium

base, decorative black enamelled aluminium

"BASKET", control gear and 70 watts high pressure

sodium lamp

695 FABRIKANT 4027 post top lantern with corrosion No 550.00

resistant die-cast aluminium alloy base and canopy,

opal diffusing cone in vandal resistant UV stabilized

high density polyethylene (HDPE-S) and complete

with control gear and 70 watts high pressure

sodium lamp / 125 mercury lamp

696 Supply of FABRIKANT post top 400mm dia No 185.00

polycarbonate opal white sphere

697 Supply of FABRIKANT die-cast aluminium alloy No 195.00

base, heat shield, control gear and lamp

698 Labour to remove existing bollards including No 10.80

reinstatement, transportation and disposal of bollards

off site

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 58: Electrical SOR

SOR 58SCHEDULE OF RATES

Item Description Unit Rate ($)

699 Removal of bollards including excavation of base, No 13.50

backfilling, reinstatement of ground surfaces,

transportation and disposal of surplus earth, base

and bollards off site

700 400 x 400 x 300 thick grade 25 concrete block act as No 15.90

base for bollards including reinstatement of ground

* Supply, deliver to site and install the following

including connecting wiring, mounting brackets,

screws, connections.

(Labour to remove existing bollard to be measured

separately)

701 'Philips' decorative bollard cat no. HGC 130 with No 441.00

opal-white cube and vandal-resistant glass-fibre

reinforced polyester column complete with 80W

NPL-N lamp and integral control gear

702 'Philips' decorative bollard cat no. HGC 130 No 451.00

with opal-white cube and vandal-resistant

glass-fibre reinforced polyester column complete

with 70W SON lamp and integral control gear

703 'Philips' decorative bollard cat no. HGC 131 No 472.00

with clear cube, built-in white lacquered

aluminium louvre system and vandal-

resistant glass-fibre reinforced polyester

column complete with 80W HPL-N lamp and

integral control gear

704 'Philips' decorative bollard cat no. HGC 131 No 472.00

with clear cube, built-in white lacquered

aluminium louvre system and vandal-

resistant glass-fibre reinforced polyster

column complete with 125W HPL-N lamp

and integral control gear

705 'Philips' decorative bollard cat no. HGC 131 No 482.00

with clear cube, built-in white lacquered

aluminium louvre system and vandal-

resistant glass-fibre reinforced polyster

column complete with 70W SON lamp

and integral control gear

706 Selux licol garden bollard 600mm ht cat No 860.00

no. SX 702 - 11 - 2 c/w 80W HPL-N lamp

and integral control gear

707 Selux licol garden bollard 600mm ht cat No 925.00

no. SX 702 - 15 - 2 c/w 80W HPL-N lamp

and integral control gear

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 59: Electrical SOR

SOR 59SCHEDULE OF RATES

Item Description Unit Rate ($)

708 Selux licol garden bollard 1000mm ht cat No 948.00

no. SX 702 - 14 - 2 c/w 50W / 70W high

pressure sodium lamp and integral control

gear

709 Selux licol garden bollard 1000mm ht No 983.00

louvred head cat no. SX 700 - 19 - 2

c/w 50W / 70W high pressure sodium

lamp and integral control gear

710 Selux licol garden bollard 1000mm ht No 956.00

louvred head cat no. SX 700 - 19 - 2

c/w 80W HPL-N lamp and integral

control gear

711 Selux licol garden bollard 600mm ht No 897.00

louvred head cat no. SX 700 - 19 - 2

c/w 50W / 70W SON lamp and intergral control gear

712 Selux garden bollard 1200mm ht cat No 890.10

no. SX 703-13-2 c/w 80W mercury lamp and

control gear, fuse box, mounting cable

713 'Mazda' decorative bollard cat no. Feria No 414.00

S70 (IP44) c/w 1 x S0N 70W lamp high

pressure sodium lamp and integral

control gear

714 'Mazda' decorative bollard cat no. Feria No 425.00

M80 (IP44) c/w 1 x 80W HPL-N lamp high

pressure mercury vapour lamp and integral

control gear

715 WE-EF GTY 25-E-70 / NI (K) Decorative No 820.00

garden bollard in corrosion resistant

die-cast aluminium alloy body and

louvres, aluminium post, built-in

control gear and 70 watts sodium lamp

716 WE-EF GRY 25-E-70 / NI (K) Decorative No 820.00

garden bollard in corrosion resistant

die-cast aluminium alloy body and

louvres, aluminium post, built-in

control gear and 70 watts sodium lamp

717 WE-EF CRY 150-E-70 / NI (K) Decorative No 720.00

garden bollard in corrosion resistant

die-cast aluminium alloy body, UV

stabilized and vandal resistant

Polycarbonate diffuser, anodized high

purity reflector, built-in control gear

and 70 watts sodium lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 60: Electrical SOR

SOR 60SCHEDULE OF RATES

Item Description Unit Rate ($)

718 WE-EF CTY 150-E-70 / NI (K) Decorative No 720.00

garden bollard in corrosion resistant

die-cast aluminium alloy body, UV

stabilized and vandal resistant

Polycarbonate diffuser, anodized high

purity reflector,built-in control gear

and 70 watts sodium lamp

719 WE-EF VSI 254-E-50 / NI (K) Decorative No 780.00

garden bollard in corrosion resistant

die-cast aluminium alloy body with

one-sided light output c/w built-in

control gear and 50 watts sodium lamp

720 WE-EF OSS 254-T-50 / NI (K) Decorative No 780.00

garden bollard in corrosion resistant

die-cast aluminium alloy body with one

sided light output c/w built-in control

gear and 50 watts sodium lamp

721 WE-EF DSS 259-E-50 / NI (K) Decorative No 780.00

garden bollard in corrosion resistant

die-cast aluminium alloy body with one

sided light output c/w built-in control

gear and 50 watts sodium lamp

722 WE-EF OSV 204-E-50 / NI (K) Decorative No 780.00

garden bollard in corrosion resistant

die-cast aluminium alloy body with one

sided light output c/w built-in control

gear and 50 watts sodium lamp

723 WE-EF DSG 259-E-50 / NI (K) Decorative No 685.00

garden bollard in corrosion resistant

die-cast aluminium alloy body with one

sided light output c/w built-in control

gear and 50 watts sodium lamp

724 WE-EF OSH 254-T-50 / NE (K) Decorative No 780.00

garden bollard in corrosion resistant

die-cast aluminium alloy body with one

sided light output c/w built-in control

gear and 50 watts sodium lamp

725 WE-EF FTY-150-E-70 / NI (K) Decorative No 820.00

garden bollard in corrosion resistant

die-cast aluminium alloy body with one

sided light output c/w built-in control

gear and 50 watts sodium lamp

726 FUMAGLLI OFIR2' Landscape luminaire c/w No 653.20

antique reeded pole moulded with resin and

reinforced with steel c/w 2 x 20W EL lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 61: Electrical SOR

SOR 61SCHEDULE OF RATES

Item Description Unit Rate ($)

727 FUMAGLLI OFIR3' Landscape luminaire c/w No 779.70

antique reeded pole moulded with resin and

reinforced with steel c/w 3 x 20W EL lamp

728 FABRIKANT 2008 decorative gardem bollard No 720.00

in corrosion resistant die-cast aluminium alloy

body and louvres, aluminium post, built-in

control gear and 70 watts high pressure sodium

lamp / 80W mercury vapour lamp

729 FABRIKANT 2048 decorative gardem bollard No 750.00

in corrosion resistant die-cast aluminium alloy

body, tempered glass diffuser, anodised high

purity reflector, built-in control gear and 70 watts

high pressure sodium lamp / 80W mercury vapour

lamp

FLOODLIGHT LUMINAIRES

730 Labour to remove existing floodlight luminaires No 10.80

including reinstatement of surfaces, tramsportation

and disposal of floodlight luminaires off site

* Supply, delivery to site and install the following

including connecting wiring, mounting, brackets,

screws, connections.

(Labour to remove existing floodlight luminaires

to be measured separately)

731 WE-EF FL 31-T-250 / N (K) Floodlight fitting of No 854.00

corrosion resistant die-cast aluminium alloy body

with cooling fins, hinged and framed safety glass

thermal shock resistant, stainless steel locking

devices, weatherproof and non-aging silicon

rubber gasket c/w RF 1-76/M/16 spigot cap,

built-in control gear and 250 watts tubular

sodium lamp

732 WE-EF FL 31-E-250 / N (K) Floodlight fitting of No 835.00

corrosion resistant die-cast aluminium alloy body

with cooling fins, hinged and framed safety glass

thermal shock resistant, stainless steel locking

devices, weatherproof and non-aging silicon

rubber gasket c/w RF 1-76/M/16 spigot cap,

built-in control gear and 250 watts elliptical

sodium lamp

733 WE-EF FL 31-T-400 / H (K) Floodlight fitting of No 864.00

corrosion resistant die-cast aluminium alloy body

with cooling fins, hinged and framed safety glass

thermal shock resistant, stainless steel locking

devices, weatherproof and non-aging silicon

rubber gasket c/w RF 1-76/M/16 spigot cap,

built-in control gear and 400 watts metal

halide tubular lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 62: Electrical SOR

SOR 62SCHEDULE OF RATES

Item Description Unit Rate ($)

734 'THORN' area floodlight cat no. OAC 400T complete No 612.00

with stirrup mounting bracket, integral control

gear and 400W-MBIF lamp

735 'THORN' area floodlight cat no. OAK 400T complete No 532.00

with stirrup mounting bracket, integral control

gear and 400W-MBF / U lamp

736 'THORN' area floodlight cat no. OAC 250T complete No 578.00

with stirrup mounting bracket, integral control gear

and 250W MBIF lamp

737 'THORN' OT 70T SON-Pak 7 floodlight c/w 70W SON No 348.00

lamp and integral control gear

738 'THORN' are floodlight cat no. CAST 250 complete No 578.00

with stirrup mounting bracket integral control

gear and 250w SON - T lamp

739 'THORN' ODW 500 halogen floodlight complete No 168.00

with K1 500w linear tungsten halogen lamp.

740 'THORN' ODW 500 halogen floodlight complete No 177.00

with K15 250w linear tungsten halogen lamp.

741 'ARCLUCE' ECO 8137 1x 70w SON slimline No 349.60

floodlight (IP55), black die cast aluminium housing

with cooling fins c/w integral control gear,

mounting bracket.

742 'PHILIPS' floodlight cat no. HNF 003 complete No 604.00

with 250w SON / T lamp, control gear mounting

bracket and weatherproof metal enlosure for

control gear.

743 'PHILIPS' floodlight cat no. HNF 003 complete No 624.00

with 400w SON / T lamp, control gear mounting

bracket and weatherproof metal enlosure for

control gear.

744 " MAZDA" 'TOUCAT' TCE EXT floodlight C/W No 950.00

remote control gear in wheather proof box and 1x400w

metal halide ( MAIH 400W) lamp / SON 250w lamp,

control gear, weather-proof metal enclosure for control

gear and stirrup mounting bracket

745 "MAZDA" CORMORAN 400 / 1000 E40 floodlight No 400.00

complete with 250w high pressure sodium vapour lamp,

control gear, weather-proof metal enclosure for control

gear and stirrup mounting bracket

746 Similar to item 745 but c/w 400w hiigh pressure No 450.00

sodium / 400w metal halide lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 63: Electrical SOR

SOR 63SCHEDULE OF RATES

Item Description Unit Rate ($)

747 " FABRIKANT" 3206 floodlight fitting of corrosion No 765.00

resistant die-cast aluminium alloy body with cooling

fins, hinged and framed safety glasss thermal shock

resistant, stainless steel locking devices, weatherproof

and non-aging silicon rubber gasket c/w RF 1-76 / m / 16

spigot cap, built-in control gear and 150 watts metal

halide tubular lamp

748 " FABRIKANT" 3208 (T) floodlight fitting of corrosion No 860.00

resistant die-cast aluminium alloy body with cooling

fins, hinged and framed safety glasss thermal shock

resistant, stainless steel locking devices, weatherproof

and non-aging silicon rubber gasket c/w RF 1-76 / m / 16

spigot cap, built-in control gear and 250 watts metal

halide tubular lamp

749 " FABRIKANT" 3208 (E) floodlight fitting of corrosion No 860.00

resistant die-cast aluminium alloy body with cooling

fins, hinged and framed safety glasss thermal shock

resistant, stainless steel locking devices, weatherproof

and non-aging silicon rubber gasket c/w RF 1-76 / m / 16

spigot cap, built-in control gear and 250 watts metal

elliptical sodium lamp

750 " FABRIKANT" 3204 (E) floodlight fitting of corrosion No 838.00

resistant die-cast aluminium alloy body with cooling

fins, hinged and framed safety glasss thermal shock

resistant, stainless steel locking devices, weatherproof

and non-aging silicon rubber gasket c/w RF 1-76 / m / 16

spigot cap, built-in control gear and 400 watts metal

halide tubular lamp

751 ' Siemens ' EUROFLOOD 701150 SICOMPACT mini No 590.00

floodlight c/w 70 / 150W metal halide or high pressure

sodium lamp and control gear

752 ' Siemens ' EUROFLOOD 250 / 400 SICOMPACT mini No 690.00

floodlight c/w 250 / 4000W metal halide or high pressure

sodium lamp and control gear

753 Hubbell' Magnuliter floodlight Cat No. MVM-0250S-166 No 639.00

complete with 250W high pressure sodium control gear

and 4024C mounting bracket

754 Hubbell' Mimiliter floodlight Cat No. MHS-0070S-166 No 471.00

for 240V operation complete with 70W high pressure

sodium control gear and 4024C mounting bracket

and 4024C mounting bracket

755 Hubbell' Primeter floodlight complete with aluminium No 360.00

body integral control gear polycarbonate diffuser with

70W SON lamp or 125W mercury vapour lamp

and 4024C mounting bracket

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 64: Electrical SOR

SOR 64SCHEDULE OF RATES

Item Description Unit Rate ($)

756 ' Philip' Anti Glare Weatherproof floodlight Cat No. No 438.00

SNF 300 c/w 250W SON / T lamp and integral control gear

757 ' Philip' Anti Glare Weatherproof floodlight Cat No. No 378.00

SNF 201 c/w 250W SON / T and one pre-wired

weatherproof die-cast control gear box

758 ' Philip' Anti Glare Weatherproof floodlight Cat No. No 435.00

SNF 201 c/w 400W HDL/ T lamp and one pre-wired

weatherproof die-cast control gear box

759 Philip' Bulk head luminaire Cat No. XGC001 complete No 181.00

with prismatic deffuser, 18W soX lamp, control gear

and mounting bracket

760 Selux ' MTR luminaire Cat No. SX 563 11 - 2 complete No 900.00

with 70W SON lamp, MTR 200 refractor and accessories

761 INDALUX QUEEN 150 - IQN' security floodlight c/w No 360.00

die-cast aluminium housing, integral contrl gear,

polycarbonate diffuser and 1 x 125W mercury lamp

762 THORLUX' PASSLIGHT security floodlight No 340.00

Cat No. PL 6235 c/w die-cast aluminium housing,

primatic glass cover / polycarbonate diffuser, intergral

control gear and 70W SON-T lamp / 80W / 125W

mercury lamp

763 "Thorn" PIAZZA security floodlight Cat. OS 50.4 / ) 70.4 No 260.00

c/w injection moulded black polycarbonate integral control

gear, polycarbonate diffuser and 50W / 70W SON-T lamp

STREET LIGHTING LANTERNS

* Supply, deliver to site and install street lighting lantern

for one 70W high pressure sodium lamp complete with

intergral compensated control gear and other accessories

as specified for the following : ( 764 770 )

764 ' Philips' Cat No. SRC 501 or SGS 201 / 070G complete No 259.00

with 70W SON - T lamp

765 Thorn ' Cat No. QB 79 WNB 1070 complete with 70W No 230.00

SON - T lamp

766 Madza ' COMETE PF S70 Steel lantern c/w integral No 320.00

control gear, cover bowl and 70W son lamp / 125W

mercury lamp

767 SIEMEN SRL S70 complete with 70W SON-T lamp No 260.00

768 ' Mazda' MACADAM PFS70 No 310.00

complete with 70W SON lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 65: Electrical SOR

SOR 65SCHEDULE OF RATES

Item Description Unit Rate ($)

769 Siemens' Cat No. 5NA 3322-OS complete with built-in No 255.00

70W high pressure sodium lamp and control gear

770 Siemens' Cat No. 5NA 3332-IS c/w built-in 150W high No 400.00

pressure sodium lamp and control gear

* Supply, deliver to site and install street lighting lantern

for 125W high pressure mercury vapour lamp complete

with intergral comensated control gear and accessories

as specified for the following : -

* ( 771 774 )

771 ' Philips ' Cat No. HGS 201 or HRC 510 / 080 - 125G No 236.00

complete with 125W HPL - N lamp

772 ' Thorn ' Cat No. QB79WB1125 complete with 125W No 219.00

MBF / U lamp

773 ' Madza ' MACADAM Cat No PF M125 complete with No 300.00

125W mercury vapour lamp, control gear and cover bowl

774 ' Siemens ' Cat No. 5NA3322-1D complete with built-in No 230.00

125W high pressure mercury lamp and control gear

* Supply, deliver to site and install street lighting lantern

for one 150W SON lamp complete with integral compensated

control gear and other accessories as specified for the

following :- *( 851 856 )

775 ' Simens ' MRL 6150 complete with 150W SON lamp No 311.00

776 ' Madza ' MACADAM GS 150 street lantern complete No 390.00

with integral control gear, cover bowl and 150W SON lamp

777 ' Philips ' Cat No. SGS 203 or SGS 201 / 150G complete No 400.00

with 150W SON lamp

778 ' Habbell ' Cat No. RMA- 3 - 3 / RMD - 15S2E - 3 No 471.00

complete with 150W SON lamp

779 ' EYE ' Cat No. H788E complete with 150W SON lamp No 446.00

780 ' Madza ' COMETE LIF S150 street lantern complete No 530.00

with integral control gear, cover bowl and 150W SON

lamp

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 66: Electrical SOR

SOR 66SCHEDULE OF RATES

Item Description Unit Rate ($)

LAMPS

* Supply and replace / install the following lamp :- *(858 872)

781 70W SON deluxe Elliptical / Tubular high pressure sodium No 43.00

vapour lamp with E27 base, ' Philips ' or other approved

type

782 150W SON high pressure sodium vapour lamp with No 58.00

E40 base, ' Philips ' or other approved type

783 250W SON deluxe Elliptical / Tubular high pressure sodium No 65.00

vapour lamp with E40 base, ( ' Philips ', Oram or Thorn )

784 50W / 80W / 125W HPL - comford high pressure mercury No 28.00

vapour flourescent lamp with E27 base ( 'Philips' or Osram )

785 400W HPI Bus high pressure metal halide gas discharge No 129.00

lamp with E40 base, ' Philips ' or other approved type

( built-in ignitor )

786 400W HPI - T Ellipticalor tubular high pressure metal No 119.00

halide gas discharge lamp with E40 base, 'Philips' or other

approved type ( built-inignitor)

787 250W HPI - T Ellipticalor tubular high pressure metal No 119.00

halide gas discharge lamp with E40 base, 'Philips' or other

approved type ( built-inignitor)

788 400W MBIF high pressure metal halide lamp G53455 No 131.00

ignitor & E40, porcelain lampholder, 'Thorn' or other

approved type.

789 250W MBIF metal halide lamp with metallic additives No 126.00

ignitor & E40 base 'Thorn' or other approved type

790 250W SON-T tubular high pressure sodium vapour No 70.00

discharge lamp with E40 base, 'Philips' or other

approved type

791 Metal halide lamp 70W HQI-TS 70W / WDL No 78.30

792 Metal halide lamp 150W HQI-TS 150W / WDL No 85.00

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 67: Electrical SOR

SOR 67SCHEDULE OF RATES

Item Description Unit Rate ($)

BALLASTS AND LAMP ACCESSORIES

* Supply and replace / install the followiwng : - 793 803

793 150W SON lamp ballast, BSN 150 L34 ' Philips' or other No 65.00

approved

794 250W SON/metal halide lamp ballast, 'Philips' or other No 70.00

approved

795 400W SON/metal halide lamp ballast, 'Philips' or other No 75.00

approved

796 80W / 125W high pressure mercury lamp ballast, BHL 80 No 49.00

L32/BHL 125 L32 'Philips' or other approved

797 250W high pressure mercury lamp ballast, BHL 250 L32 No 60.00

Philips' or other approved

798 400W high pressure mercury lamp ballast, BHL 400 L32 No 75.00

Philips' or other approved

799 150W / 250W / 400W SON/metal halide lamp ignitor, No 39.00

( 'Philips', Parmar, Bag Turgi)

800 E27 Porcelain lampholder for discharge lamp No 12.00

801 E40 Porcelain lampholder for discharge lamp No 15.00

802 Ballast for 7W / 9W / 11W PL lamp No 15.00

( 'Philips', ATIO, Vossloh Sch)

803 Ballast for PLC 13W / 18W lamp 'Philips' or other approved No 16.00

WEATHERPROOF AND METAL ENCLOSURES

* Supply and install the following : - * ( 804 809 )

804 Vynckier Superpolyrel SP 320 500 x 750 x 300 mm complete No 863.00

with rainhood, air vents, handle, lock and key and gasket

for IP55

805 Vynckier Superpolyrel SP 330 750 x 750 x 300 mm complete No 1061.00

with rainhood, air vents, handle, lock and key and gasket

for IP55

806 Vynckier Superpolyrel SP 430 1000 x 750 x 300 mm complete No 1224.00

with rainhood, air vents, handle, lock and key and gasket

for IP55

807 160 x 135 x 77 mm plastic rectangular base, ' Legrand ' No 21.70

Cat No. 92106 or other approved

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 68: Electrical SOR

SOR 68SCHEDULE OF RATES

Item Description Unit Rate ($)

808 310 x 240 x 154 mm plastic rectangular base with hinged No 145.00

cover, 'Legrand' Cat. No. 35054 or other approved

809 280 x 200 x 150 mm metal box No 37.00

PAINTING OF LIGHTING COLUMNS

( Colour of paint to be determined by the S. O. )

810 Prepare and paint one coat of primer and two coats of No 13.30

synthetic enamel paint, onto the external surface of the

lighting columns for 8m street lighting colums with

single arm bracket

811 Prepare and paint one coat of primer and two coats of No 14.10

synthetic enamel paint, onto the external surface of the

lighting columns for 8m street lighting colums with

double arm bracket

812 Prepare and paint one coat of primer and two coats of No 8.30

synthetic enamel paint, onto the external surface of the

lighting columns for 3m post top lighting column

813 Prepare and paint one cost of primer and two coats of No 12.20

synthetic enamel paint, onto the external surface of the

lighting columns for 8m post top lighting column

814 Prepare and paint one coat of primer and two coats of No 15.60

synthetic enamel paint, onto the external surface of the

lighting columns for 10m post top lighting column

815 Prepare and paint one coat approved aluminium paint No 12.20

to existing lamp poles including spraying lamp post

indicator with approved black paint and all necessary

supports, etc

816 Prepare and paint two coats approved aluminium paint No 17.20

to existing lamp poles including spraying lamp post

indicator with approved black paint and all necessary

supports, etc

817 Paint identification numbers (Block No. / Lamp Pole No.) Pole 1.80

on to existing lamp poles of size not exceeding 150 mm

in height

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 69: Electrical SOR

SOR 69SCHEDULE OF RATES

Item Description Unit Rate ($)

LIGHTING COLUMNS

* Supply, deliver to site, erect and install lighting columns

complete with 5 Amp 'HRC' fuse, accessories, cable glands,

shrouds, locks, internal wiring including painting

identification numbers as detailed in Standard Drawing

Nos. EM-LC (CP) - 90 - 1&2 to location as directed.

(Removal and reposition of existing lighting columns

to be measured separately) *( 818 837)

818 Single arm 8-metre HOT DIP GALVANISED lighting No 690.00

column all as shown including all necessary concrete

foundation, cement skirting, excavation, backfilling and

reinstatement of ground surfaces

819 Double arm 8-metre HOT DIP GALVANISED lighting No 740.00

column all as shown including all necessary concrete

foundation, cement skirting, excavation, backfilling and

reinstatement of ground surfaces

820 8 metre post top HOT DIP GALVANSIED lighting column No 700.00

all as shown including all necessary concrete foundation,

cement skirting, excavation, backfilling and reinstatement

of ground surfaces

821 10 metre post top HOT DIP GALVANISED lighting column No 790.00

all as shown including all necessary concrete foundation,

cement skirtng, excavation, backfilling and reinstatement

of ground surfaces

822 3M or 3.75m post top HOT DIP GALVANISHED lighting No 380.00

column all as shown including all necessary concrete

foundation, cement skirting, excavation, backfilling and

reinstatement of ground surfaces

823 Double arm 3-metre HOT DIP GALVANISED lighting No 398.00

column and powder coated black colour

824 Double quarter arm 3.5 - metre HOT DIP GALVANISED No 527.00

lighting column and powder coated black colour

825 Single quarter arm 3.5 - metre HOT DIP GALVANISED No 634.00

lighting column and powder coated black colour

826 Supply and fix hotdip galvanised bracket metal arm to No 103.00

lighting column to match existing (single arm)

827 Supply and fix hot dip galvanised bracket metal arm to No 140.00

lighting column to match exisitng (double arm)

828 Supply and fix 80mm diameter 200mm length steel adaptor No 42.00

with spigot to lighting column for mounting or post top

lantern c/w mounting screws

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 70: Electrical SOR

SOR 70SCHEDULE OF RATES

Item Description Unit Rate ($)

829 Supply and fix hot dip galvanised metal door c/w locking No 35.00

facilities to match existing lighting column

830 Supply and fix corrosion resistant aluminium wall bracket, No 117.00

'PGL' Cat No. P/BM-448 or other approved type

831 Supply and fix corrosion resistant aluminium double arm No 268.00

bracket for post top mounting, 'PGL' Cat No. P/T-2 or

other approved

832 Supply and fix corrosion resistant aluminium triple arm No 325.00

bracket for post top mounting, 'PGL' Cat No. P/T-3 or

other approved

833 "WE-EF" A 50-400.60 corrosion resistant aluminium No 196.00

wall bracket

834 "WE-EF" AS 20-400 corrosion resistant aluminium No 370.00

double arm bracket for post top mounting

835 "WE-EF" AS 30-400 corrosion resistant aluminium No 494.00

triple arm bracket for post top mounting

836 "WE-EF" MF1-A-108 steel mounted bracket for single No 135.00

floodlight on post top column

837 "WE-EF" MF2-A-108 steel mounted bracket for two No 240.00

floodlight on post top column

838 Supply and fix steel mounted bracket for single flood No 80.00

light luminaire on post top column

839 Supply and fix steel mounted bracket for two flood No 120.00

lights luminaires on post top column

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 71: Electrical SOR

SOR 71SCHEDULE OF RATES

Item Description Unit Rate ($)

SECTIONAL TAPERED OCTAGONAL HOT-

DIPPED GALVANISED LIGHTING COLUMN

* Supply, deliver to stie, erect and install the following

lighting complete with 5Amp 'HRC' fuse accessories

cable glands, shrouds, locks, internal wiring including

painting identification number, bitumen coating of

planted section, all necessary excavation, concrete

skirting, backfilling and reinstatement of ground surfaces.

( Removal and reposition of existing lighting cloumn to

be measured separately )

840 "LYCORPOLE" 8 metre lighting column complete with No 520.00

single arm bracket 2m length outreach

841 "LYCORPOLE" 8 metre lighting column complete with No 630.00

double arm bracket 2m length outreach

842 "LYCORPOLE" 3 metre post lighting column No 274.00

(without skirting)

843 'LYCORPOLE' 8 metre post top lighting column No 591.00

844 'LYCORPOLE' 10 metre post top lighting column No 715.00

845 'PETITJEAN' 8 metre octagonal hot-dipped galvanised No 500.00

flange pole complete with 2m single outreach arm

846 'PETITJEAN' 8 metre octagonal hot-dipped galvanised No 580.00

flange pole complete with 2m double outreach arm

847 'PETITJEAN' 5 metre swaged post top hot-dipped No 330.00

galvanised embedded pole c/w L bracket

848 'PETITJEAN' 4 metre swaged post top hot-dipped No 290.00

galvanised embedded pole c/w L bracket

849 'PETITJEAN' 3 metre swaged post top hot-dipped No 260.00

galvanised embedded pole c/w L bracket

850 'PETITJEAN' 3 metre octagonal post top hot-dipped No 265.00

galvanised embedded pole

851 'PETITJEAN' 3.5 metre octagonal post top hot-dipped No 300.00

galvanised embedded pole

852 'PETITJEAN' 5 metre octagonal post top hot-dipped No 360.00

galvanised embedded pole

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 72: Electrical SOR

SOR 72SCHEDULE OF RATES

Item Description Unit Rate ($)

REMOVAL AND REPOSITION OF EXISTING

LIGHTING COLUMNS (INCLUDING BRACKET

ARM AND LUMINAIRE)

853 Removal of lighting column inclding excavation, taking off No 220.00

of poles, backfilling, reinstatement of ground surfaces,

transporation to new site, re-erect and install 8m to 12m

lamp pole

854 Removal of lighting column including excavation, taking off No 141.50

of poles, backfilling, reinstatement of ground surfaces,

transportation to new site, re-erect and install 5m to 6.6m

street lighting lamp pole

855 Removal of lighting column including excavation, taking off No 113.00

of poles, backfilling, reinstatement of ground surfaces,

transportation to new site, re-erect and install 3m to 4m

lamp pole

856 Removal of 5m to 12m lighting column including excavation, No 112.00

taking off of poles, backfilling, reinstatement of ground

surfaces, transportation and disposal of surplus earth

and column from site

857 Removal of 3m to 4m lighting column including excavation, No 77.00

taking off of poles, backfilling, reiinstatement of ground

surfaces, transportation and disposal of surplus earth

and column from site

REPLACEMENT OF DEFECTIVE STREETLIGHT

COVER BOWLS

* Remove existing defective streetlight cover bowl, supply

and fix new cover bowl including all accessories for the

following lighting lantern : - *( 858 865 )

858 " Philips " Cat No. SGS 201-070G / SRC 510 - 070G No 54.00

859 " Thorns " Cat No. QB 79 WNB 1070 No 65.00

860 " Mazda " Cat No. SOLAIR 125 No 76.00

861 " Mazda " Cat No. COMETE P S70 No 76.00

862 " Philips " Cat No. HGS 201 / HRC 510 / 080 - 125G No 59.00

863 " Thorn " Cat No. QB 79 WB 1125 No 65.00

864 " Mazda " Cat No. SOLAIR 251 No 84.00

865 " Philips " Cat No. SGS 201 / SGS 203 / 150G No 60.00

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 73: Electrical SOR

SOR 73SCHEDULE OF RATES

Item Description Unit Rate ($)

LABOUR ONLY ITEMS

866 Labour for replacement lamp holder wiring No 4.40

867 Skilled electrician for checking defective witing, fuses, Per Job 23.00

times switches, including repair where necessary in meter

room / control box

868 Labour for checking defective lamp post wiring, fuses, Per Post 17.00

including tracing fault & repair where necessary

869 Labour only for removal or tighting stay wire from Per Post 10.00

lamp post

870 Labour for reconnecting overhead cable Pole 14.90

871 Labour for removing existing / defective 5 to 12 m lighting Per Pole 69.00

column including bracket arm & luminaire

(excluding excavation)

872 Labour for refixing loosen lamp cover Per Pole 6.50

873 Labour for removing existing / defective 3 to 4 m lighting Per Pole 48.00

column including bracket arm & luminaire

(excluding excavation)

874 Labour for refixing loosen lamp fitting Per Pole 6.50

875 Labour for dismantling single / double lamp post arm Per Pole 29.90

876 Labour for refixing single / double arm to lamp post Per Pole 29.90

877 Labour for repositioning single / double arm to lamp Per Pole 29.90

poast's arm

878 Labour for repositioning and realigning lamp post not Per Pole 57.00

exceeding 4 m height including all necessary excavation

and make good all works affected on completion

879 Labour for repositioning and realigning lamp post exceeding Per Pole 89.00

4m but not exceeding 8 m height including all necessary

excavation and make good all works affected on completion

880 Labour for repositioning and realigning lamp post exceeding Per Pole 101.00

8m but not exceeding 12 m height including all necessary

excavation and make good all works affected on completion

881 Labour for checking and locating underground cable Per Pole 133.00

short-fault c/w excavation and make good all works

affected on completion

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]

Page 74: Electrical SOR

SOR 74SCHEDULE OF RATES

Item Description Unit Rate ($)

MISCELLANEOUS

882 Ripple control receiver for existing public lighting installation No 340.00

- two relay type

883 Ripple control receiver for existing public lighting installation No 400.00

- three relay type

884 Supply and replace post top 400 mm diameter polycarbonate No 144.00

opal white sphere (other than FABRIKANT & WE - EF)

885 Supply and replace 400 mm diameter polycarbonate clear / No 153.00

smoke sphere (other than WE-EF)

886 Supply and install metal base for post top spheric lantern No 37.00

c/w mounting screws and connections

887 Provide 200-300 mm high and 50 mm thick circular on plan No 34.00

concrete base to lighting column including all necessary

excavation and making good

888 Provide 300 - 450 mm high concrete pedestal base for No 61.00

westherproof / outdoor control box c/w mounting screws

and brackets

889 Supply and install 200 watt E / 27 Rough Device lamp bulb No 12.00

890 Supply and install supporting bracket consisting of 75 mm No 68.00

diameter galvanised pipe with 200mm x 75mm x 19mm

supporting tray, 300mm x 300mm x 3mm bottom base place

and concrete footing

891 Supply and install timer relay c/w base for zebra crossing No 120

warning light

892 Supply and install post top yellow globe 300mm diameter No 180

for zebra crossing

893 Rental for the 'Wildcat' self propelled work platforms Per Mth 1600

Model 2032 with working height of 7.90m, overall length

2.30m, platforms capacity 800 lbs

CD16/SOR-Electrical Re-Wiring Upgrading/Rewiring-SOR.Xls/(1)/[2007 Edition]