emergency light fittings for fluorescent lamps series exlux 6008

Upload: midfiild-cosmin

Post on 06-Jul-2018

215 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/16/2019 Emergency Light Fittings for Fluorescent Lamps Series EXLUX 6008

    1/2

    R. STAHL Schaltgeräte GmbH Page 1 / 2Data Sheet 27.08.2012

    R. STAHL Schaltgeräte GmbH 169732P.O. Box 40 - D-74636 Waldenburg - Tel. 07942 943-0 - Fax 07942 943-4333

    e-mail: [email protected] - Internet: http://www.stahl.de

    Page / Data SheetIdent-No.169732

    Ident-No. 169732

    Order number  6008/542-9011-7147

    Emergency Light Fittings for Fluorescent Lamps Series EXLUX 6008

    Luminous Characteristics

    Lamps 2 x 36 W W

    Battery 7 Ah

    Lighting hours 1.5 / 3 h (emergency light)

    Explosion protection

    Global (IECEx)

    IECEx IECEx PTB 07.0053

    Gas explosion pro-

    tection

    Ex d e mb IIC T4

    Dust explosion pro-

    tection

    Ex tD A21 IP66 T80°C

    Europe (ATEX)

    Gas explosion pro-

    tection

    PTB 97 ATEX 2032

    Gas explosion pro-

    tection

      II 2 G Ex d e mb IIC T4

    Dust explosion pro-

    tection

    PTB 97 ATEX 2032

    Dust explosion pro-

    tection

     

    II 2 D Ex tD A21 IP6. T80°C

    Certificates and appro-

    vals

    Certificates IECEx, ATEX, Brazil (UL do Brasil), India (PESO), Canada (CSA), Kazakhstan (GOST-K), Rus-

    sia (GOST-R), Ukraine (GOST-U), USA (FM), Belarus (GOST-B), Serbia (IZP), Corea KGS),

    China (CQST)

    Other approvals ship approval (GL)

    Further parameters

    Marking (CE) 

    0158

    Electrical data

    Rated voltage 220 ... 254 V, 50 / 60 Hz

    110 ... 127 V, 50 / 60 Hz available on request

    Disconnection of the light When opening the light

    Switch with safety lock; when opening the central lock, all poles of the voltage supply to the

    ballast are disconnected; contacts of the switching element are NC contacts, they can only

    switched on again when the lamp cover and the central locking system are closed.

    In case of a lamp fault, the electronic ballast disconnects the defective lamp from the power 

    supply.

    Emergency light electronics

    Operating modes Continuous operation, continuous operation with emergency light blocking and stand-by

    switching

    Battery charge Intelligent battery management, controlled microprocessor (charging time max. 14 h) total dischargeprotection to avoid a pole reversal

  • 8/16/2019 Emergency Light Fittings for Fluorescent Lamps Series EXLUX 6008

    2/2

    R. STAHL Schaltgeräte GmbH Page 2 / 2Data Sheet 27.08.2012

    R. STAHL Schaltgeräte GmbH 169732P.O. Box 40 - D-74636 Waldenburg - Tel. 07942 943-0 - Fax 07942 943-4333

    e-mail: [email protected] - Internet: http://www.stahl.de

    Switchover voltage from mains to battery operation for U < 0.74 x UNfrom battery to mains operation for U > 0.80 x UN

    Test functions

    Functional test The emergency light function is checked once a week

    First test takes place 1 hour after putting into operation

    For the first test, both lamps are switched on for 1 minute and the battery is charged with the

    rated current.

    Battery errors and lamp faults are detected and indicated via the LED.

    Light duration test of the

    emergency lighting

    Test of the battery capacity in time intervals of 12 months; operation of the device in the

    emergency light mode during 2/3 of rated operation time. If the light is switched off by the

    discharge protection before the time has elapsed, the battery cannot be used for the emer-

    gency mode.

    The red LED indicates the error.

    Battery set

    Version Gas-tight NiCd battery

    Operating voltage 6 V

    Capacity 7 Ah

    Replacing the battery set When the battery enclosure is opened, the battery set is de-energised;

    the battery set can be removed from the enclosure after disconnection of the plug-in

    contacts

    Mechanical data

    Ambient conditions

     Ambient temperature Standard operation: - 20 ... + 50 °C

    Battery operation: - 5 ... + 50 °C charging, - 20 ... + 50 °C discharging

    Material

    Enclosure material Polyester, glass fibre reinforced, colour: white, similar to RAL 9010

    Lamp cover  Polycarbonate

    Gasket Polyurethane foam gasket in the lamp cover 

    Lamp locking Central locking which can be opened/closed using a socket key M8 / wrench size 13, hinged

    lamp cover 

    Connection Polyamide terminal block with cover

    Marking: L1, N, PE, L’ (L’ = charging phase)

    Connection range: max. 2 x 6 mm2 (solid), 2 x 4 mm2 (flexible)

    Weight 10.400 kg

    Cable entry Connection side: 1 cable gland M 25 x 1.5 and 1 stopping plug M 25 x 1.5

    Opposite side: 1 stopping plug M 25 x 1.5

    Connection Polyamide terminal block with cover

    Marking: L1, N, PE, L’ (L’ = charging phase)

    Connection range: max. 2 x 6 mm2 (solid), 2 x 4 mm2 (flexible)

    Through wiring without

    Dimensions

    Dimensional Drawings (All Dimensions in mm) - Subject to Alterations

    We reserve the right to make alterations to the technical data, weights, dimensions,

    designs and products available without notice. The illustrations cannot be considered

    binding.