exam 642-901 preparation questions

Exam 642-901 study material

Made available by CertsKing.com

Free 642-901 Exam Preparation Questions

Exam 642-901: BSCI - Building Scalable Cisco Internetworks

For Latest 642-901 Exam Questions and study guides- visit- http://www.certsking.com/642-901.html

http://www.certsking.com/642-901.html



Question:1 Refer to the exhibit. On the basis of the information in the exhibit, which two statements are true? (Choose two.)

A. The output was generated by entering the show ip bgp command on the ISP router. B. The serial 0/0/1 interface on the ISP router has been configured with the set metric 50 command. C. The output was generated by entering the show ip bgp command on the Company1 router. D. When traffic is sent from the ISP to autonomous system 64512, the traffic will be forwarded to Company1 because of

the lower MED value of Company1.

Answer: A, D

Question:2 The term routing protocol may refer more specifically to a protocol operating at Layer 3 of the OSI model which similarly disseminates topology information between routers. Which two routing protocols require a metric to be configured when redistributing routes from other protocols? (Choose two.)

A. RIP B. IS-IS C. EIGRP D. OSPF

Answer: A, C Question:3 Mobile IPv6 provides route optimization mechanism for fast communication by lessening the overhead of indirection. A mobile IPv6 binding is an association between which of the following? (Choose two)

A. Care-of address


B. Prefix C. Correspondent nodes D. Home address

Answer: A, D

Question:4 Which statement best describes OSPFv3?

A. Authentication is supported through IPSec. B. Point-to-multipoint mode is no longer an option for interfaces. C. Neighbor discovery has been enhanced over OSPFv2 to allow multiple adjacencies. D. Multiple DRs are allowed on a broadcast segment.

Answer: A

Question:5 Study the network diagram carefully, which routers currently compose the IS-IS backbone?

A. P4S2, P4S3, P4S6, P4S7 B. P4S3, P4S4, P4S6 C. P4S3, P4S4, P4S5, P4S6 D. P4S2, P4S3, P4S4, P4S6, P4S7

Answer: D

Question:6 A Company network administrator is managing a hub-and-spoke network with EIGRP routing enabled. The hub router is trying to query a remote router. But, delays are occurring that are caused by certain paths being stuck in active (SIA). How should the administrator configure EIGRP in order to limit the scope of the query range and prevent SIA from occurring?

A. Configure the hub to indicate that the remote router is a stub router. B. Configure the hub and remote router as stub routers.


C. Configure the remote router as a stub router. D. Disable the SIA feature of EIGRP on the remote router.

Answer: C

Question:7 Which one of the following commands enables a multicast routing protocol on an IOS device?

A. (config-if)#multicast address {IP-address} B. (config)#ip multicast routing C. (config-if)#ip pim {dense-mode | sparse-dense-mode | sparsemode} D. (config)#ip pim send-rp-announce {interface type} scope {ttl} group-list {acl}

Answer: C

Question:8 Which routing protocols will support IPv6? (Choose two)

A. RIPv2 B. EIGRP C. OSPFv3 D. ODR

Answer: B, C

Question:9 Which statement accurately describes Dual stack ?

A. Running IPv4 and IPv6 at the same time B. Process interception C. Passing IPv6 through UDP D. Translating IPv4 traffic to IPv6

Answer: A

Question:10 6 to 4 is an automatic tunnel Givesa prefixto the attachedIPv6 network. How is a 6-to-4 tunnel different than a manually configured tunnel?

A. It is not a dual-stack solution B. It uses NAT-PT C. Automatic tunnel creation D. IPv6 addresses are embedded in IPv4 addresses

Answer: C

Question:11 As shown in the exhibit ,OSPF is configured over a Frame Relay network. All PVCs are active. However, P4S1 and P4S3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on P4S2 displays the state of the neighbors. In order to fix the problem , what should be done?


A. The neighbor command should be configured under the OSPF routing process on all routers. B. The ip ospf network broadcast command should be configured on each Frame Relay interface. C. The ip ospf network non-broadcast command should be configured on each Frame Relay interface. D. The ip ospf priority value on the spoke routers should be set to 0.

Answer: D

Question:12 According to the following output, can you tell me which command can edistribute IGRP into EIGRP?

Router eigrp 123 Network 10.10.10.0 No auto-summary ! Router igrp 123 Network 172.16.0.0 Network 172.17.0.0

A. Under the router eigrp mode add redistribute igrp 123 subnets B. Under the router igrp mode add redistribute eigrp 123 C. Under the router eigrp mode add redistribute igrp 123 D. None, EIGRP and IGRP are automatically redistributed in this instance.

Answer: D

Question:13 Intermediate system to intermediate system (IS-IS), is a protocol used by network devices (routers) to determine the best way to forward datagrams through a packet-switched network, a process called routing. Which three attributes are of the IS-IS routing protocol?

A. link-state routing protocol B. operation is similar to BGP C. supports VLSM D. supports two routing levels within an autonomous system

Answer: A, C, D

Question:14 On the basis of the following presented exhibit, what will happen after configuring the neighbor 10.1.1.1 weight 200 BGP configuration command on router P4S-A?


A. P4S-A will prefer the path through P4S-B for network 172.20.0.0. B. Packets from P4S-D will prefer the path through P4S-C for networks advertised by P4S-A. C. P4S-A will prefer the path through P4S-C for network 172.20.0.0. D. Packets from P4S-D will prefer the path through P4S-B for networks advertised by P4S-A

Answer: A

Question:15 Which feature is a must for the BGP update packet?

A. Weight B. LOCAL_ PREF C. AS_Path D. AGGREGATOR

Answer: C

Question:16 Which description regarding OSPF Network LSAs is correct?

A. They are originated by Area Border Router and are sent into a single area to advertise an Autonomous System Border Router.

B. They are originated by the DR on every multi-access network. They include all attached routers including the DR itself.

C. They are originated by every router in the OPSF network. They include all routers on the link, interfaces, the cost of the link, and any known neighbor on the link.

D. They are originated by Area Border Routers and are sent into a single area to advertise destinations outside that area.

Answer: B

Question:17 The Border Gateway Protocol (BGP) is the core routing protocol of the Internet. It maintains a table of IP networks or 'prefixes' which designate network reachability among autonomous systems (AS). In routing updates, which BGP feature will not be advertised to o its neighboring routers?

A. weight


B. next hop C. local preference D. origin

Answer: A

Question:18 When CDP finds out that a Cisco phone is attached, which three interface commands should be used in order for the switch port to support a connected Cisco phone and to trust the CoS values received on the port? (Choose three.)

A. switchport priority extend cos_value B. mls qos trust cos C. mls qos trust device cisco-phone D. switchport voice vlan vlan-id

Answer: B, C, D

Question:19 Open Shortest Path First (OSPF) is a routing protocol developed for Internet Protocol (IP) networks by the Interior Gateway Protocol (IGP) working group of the Internet Engineering Task Force (IETF). Which two statements best describe the OSPF link-state routing protocol? (Choose two.)

A. OSPF sends updates every 10 seconds. B. When a link state is changed, the router that detected the change creates a link-state advertisement (LSA) and

propagates it to all OSPF devices using the 224.0.0.6 multicast address. C. OSPF sends summaries of individual link-state entries every 30 minutes to ensure LSDB synchronization. D. OSPF sends triggered updates when a network change occurs.

Answer: C, D

Question:20 What will happen after redistributing other routing protocol routes into OSPF?

A. miss the metric option in the redistribute command. B. miss the subnet option in the redistribute command. C. miss the tag option in the redistribute command. D. misconfigure the metric-type option in the redistribute command to type-1.

Answer: B

Question:21 Refer to the following IPv6 addresses, which one could correctly compress the IPv6 unicast address 2001:0:0:0:0DB8:0:0:417A?

A. 2001:::0DB8:0:0:417A B. 2001:0DB8:417A C. 2001::0DB8::417A D. 2001::DB8:0:0:417A

Answer: D

Question:22 A routing loop is a common problem with various types of networks, particularly computer networks. They are formed when an error occurs in the operation of the routing algorithm, and as a result, in a group of nodes, the path to a particular destination forms a loop. Which BGP feature can prevent routing loops?


A. AS-path B. weight C. local preference D. origin

Answer: A

Question:23 OSPF is a link-state routing protocol that calls for the sending of link-state advertisements (LSAs) to all other routers within the same hierarchical are a. In the network provided in the following exhibit, each router is configured with OSPF. But, router P4S-R1 can??t receive a default route to router P4S-R2 as expected. How to solve this problem?

A. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router P4S-R2. B. Add the always keyword to the default-information originate configuration command on router P4S-R2. C. Add the area 1 stub command on routers P4S-R1. D. Remove the default information originate configuration command from router P4S-R2 and place it on router P4S-

R1.

Answer: B

Question:24 The Border Gateway Protocol (BGP) is the core routing protocol of the Internet. It maintains a table of IP networks or 'prefixes' which designate network reachability among autonomous systems (AS). Look at the following presented BGP configuration commands from the advertising router seriously, it is found that the 192.168.0.0 route is not being advertised in this network. Why?

router bgp 65111 neighbor 172.16.1.1 remote-as 65111 neighbor 172.16.2.1 remote-as 65112 network 192.168.0.0 network 10.0.0.0 ! ip route 192.168.0.0 255.255.0.0 null0

A. The network 192.168.0.0 statement is missing mask 255.255.0.0 B. The auto-summary configuration is missing.


C. The network 192.168.0.0 statement is missing mask 0.0.255.255. D. The network 10.0.0.0 statement is missing mask 255.0.0.0.

Answer: A

Question:25 DR (Designated Router) is for environments where many routers on the same network such as Ethernet. In the following presented network, all routers are reloaded simultaneously, and DR is selected as expected. What is the P4S-RTC status?

A. 2WAY/DR B. FULL/DROTHER C. FULL/BDR D. FULL/DR

Answer: C

Question:26 According to the diagram displayed below, which address can summarize the presented networks successfully?


A. 192.168.0.0/24 B. 192.168.8.0/20 C. 192.168.8.0/21 D. 192.168.12.0/20

Answer: C

Question:27 During selecting the BGP path on a Cisco router, which BGP feature will be first used to determine the best path?

A. origin B. next-hop C. weight D. AS-path

Answer: C

Question:28 Observe the following exhibit carefully, the interfaces addresses on P4S-RA are 192.168.1.1 and 172.16.1.1, while the interfaces addresses on P4S-RB are 172.16.1.2 and 10.1.1.2. P4S-RA serial link is used to connect the two routers. Which command can be issued to configure P4S-RB with RIPv2?


Answer:


Question:29 Look at the following exhibit carefully, then select a command which can generate a default route on P4S-R2 to reach all other networks except P4S-R1?

A. ip route 0.0.0.0 0.0.0.0 192.168.2.2 B. ip route 192.168.1.0 255.255.255.0 s0/0/0

C. ip route 10.0.0.0 255.255.255.0 s0/0/0 D. ip route 0.0.0.0 255.255.255.0 192.168.2.2

Answer: A Case Study# 1

Scenerio:


Refer to the exhibit, Bigbids incorporated is a worldwide aution provider. The netword user EIGRP as its routing protocol throughout the orporation. The network administrator does not understand the convergence of EIGRP. Using the output of the show ip eigrp topology all-links command, answer the administrator’s question.

Topology: Case Study #1 (Questions)

Question:30 Which three EIGRP routers will be installed for the 172.29.3.128/25 and 172.29.2.0/24 networks? (choose three)

A. 172.29.3.128/25 [90/28160] via 172.29.1.2, 01:26:35, FastEthernet0/2 B. 172.29.2.0/24 [90/30720] via 172.29.10.2, 02:10:11, FastEthernet0/1 C. 172.29.3.128/25 [90/30720] via 172.29.3.2, 01:20:35, FastEthernet0/3 D. 172.29.3.128/25 [90/30720] via 172.29.10.2, 01:26:35, FastEthernet0/1

Answer: B, C, D

Question:31 Which two networks does the P4S-SW1 device have feasible successors for? (choose two)

A. 10.19.0.0/24 B. 172.29.2.0/24 C. 172.29.1.0/24 D. 172.29.0.0/30

Answer: A, D

Question:32 Which three networks is the router at 172.29.10.2 directly connected to ? (choose three)

A. 172.29.0.0/30 B. 172.29.2.0/24 C. 172.29.3.128/25 D. 172.29.10.0/24


Answer: B, C, D Case Study# 2

Scenerio: Look at the following exhibit. FunGames Incorporated is a famous gaming supplier. EIGRP is used throughout the company as the protocol of the network. Assume that the network engineer know nothing of the convergence of EIGRP. You are required to use the output of the show ip EIGRP topology all-links command to answer the questions asked by the engineer.

Topology: Case Study# 2 (Questions)

Question:33 Choose three EIGRP routes that will be installed for network 172.18.3.128/25 and 172.18.2.0/24? (Choose three)

A. D 172.18.2.0/24[90/30720]via 172.18.10.2,02:10:11,FastEthernet0/1 B. D 172.18.2.0/24[90/33280]via 172.18.3.2,02:10:11,FastEthernet0/3 C. D 172.18.3.128/25[90/30720]via 172.18.3.2,01:26:35,FastEthernet0/3 D. D 172.18.3.128/25[90/30720]via 172.18.10.2,01:26:35,FastEthernet0/1


Answer: A, C, D

Question:34 Choose two networks for which the Switch1 device has feasible successors. (Choose two)

A. 172.18.2.0/24 B. 172.18.3.0/25 C. 10.24.0.0/24 D. 172.18.0.0/30

Answer: C, D

Question:35 Choose three networks to which the router at 172.18.10.2 directly connected. (Choose three)

A. 172.18.3.128/25 B. 172.18.3.0/25 C. 172.18.2.0/24 D. 172.18.10.0/24

Answer: A, C, D

Question:36 Which two of the following are reasons for the failure of BGP neighbor stablishment?

A. There is an access list blocking all TCP traffic between the two BGP neighbors. B. The BGP update interval is different between the two BGP neighbors. C. The IBGP neighbor is not directly connected. D. The BGP neighbor is referencing an incorrect autonomous system number in its neighbor statement.

Answer: A, D


For complete Exam 642-901 Training kits and Self-Paced Study Material

Visit:http://www.certsking.com/642-901.html

http://www.certsking.com/


http://www.certsking.com/



exam 642-901 preparation questions

Documents

remote router

ipv6 answer

hub router

c question

company1 router

isp router

d question

p4s7 answer