f.254-i-t

8/11/2019 F.254-I-T

1/139

The Challenge Machinery Company provides owner'smanuals on its products solely as a courtesy to its customers.See the information below before using this manual.

These manuals are for reference only. These manuals include products which are non-current, unsupported or no longer produced by The Challenge Machinery Company, and are

provided solely as an accomodation to our customers. By providing these manuals, TheChallenge Machinery Company makes no representation or warranty as to the products,their current condition, or their suitability or fitness for use in any particular application, whichare the sole and independent responsibility of the product owner and user.

Older products may not comply with current safety procedures, guidelines or regulations,and it is the product owner's and user's respons ibil ity to evaluate the suitability and fitness ofthe products in their current use and application. The Challenge Machinery Company makesno representation, warranty or recommendation regarding any modifications which may berequired on non-current or unsupported products. The Challenge Machinery Companyassumes no liabil ity for any modification or alteration to any Challenge product, and any such

modification or alteration to any Challenge product is not authorized by The ChallengeMachinery Company. The availability of these manuals is solely for the purpose of providingreference information for the products.

This manual may not be complete in all aspects of product maintenance and repair. Allproducts should be used only by qualified and properly trained personnel, following propersafety procedures.All products should be regularly inspected and maintained, and their condition,

application and use should be periodically evaluated by qualified personnel. Only qualified andproperly trained technicians should perform maintenance, repair and replacementprocedures. Attempting these procedures without proper training may cause machinedamage or operator injury!

Products may be unsupported by The Challenge Machinery Company due to age or thunavailabilityof parts from their original manufacturer. No parts or product support will bavailable to repair or maintain unsupported products. Older products may not be UL listed (the product does not have a UL label it is not a listed product), and may not comply withapplicable installation or other regulations or requirements if relocated to a new facilityMany municipalities require a product to be UL listed before an electrician will connect poweto them. Often the cost of updating an older product to comply with current safety regulations greater than the value of the product.

8/11/2019 F.254-I-T

2/139

F.254-I-TFeb 2011

C H A M P IO N 3 0 5 P A P ER C U T T IN G

M A C H IN E

M o d e ls X , X G , X T

Sold and Serviced byThe Challenge Machinery Company

6125 Norton Center DriveNorton Shores, MI 49441-6081 USA

ChallengeMachinery.com

Serial Numbers 07X1360 & Up

T ECH N IC A L

M A N U A L

8/11/2019 F.254-I-T

3/139

1.0 Introduction

2

1.0 IntroductionThis manual is designed to help you get the most from your Challenge equipment. Keep this manualin a safe, convenient place for quick reference by operators and service personnel.

SAFETY ALERT! This symbol means CAUTION: Personal safety in-structions! Pay special attention to the instructions in bold type. Personal injury may result if theprecautions are not read and followed.

READ THIS MANUAL BEFORE OPERATING! Follow the precautions and instructions given. If af-ter reading the manual questions still remain, contact your Authorized Challenge Dealer.

FOR PARTS AND SERVICE, contact the Authorized Challenge Dealer from whom you purchasedthe machine. Use the illustrations and parts lists at the back of this manual to identify the correctparts needed. Always give theSERIAL NUMBER andMODEL of your machine to insure the correctparts are sent as soon as possible.

RECORD YOUR MACHINE SERIAL NUMBER in the space provided on the front cover of this man-ual. Fill out the warranty card accompanying your machine and return it DIRECTLY TO CHAL-LENGE.

If you bought a used machine, it is important to have the following information on record at Challenge.Copy this page, fill in the information and send it care of The Challenge Service Department, 6125

Norton Center Drive Norton Shores MI 49441.

CHALLENGE MODEL SERIAL NUMBER

ATTN COMPANY

ADDRESS

CITY STATE/PROVINCE ZIPPHONE DATE INSTALLED

DEALER NAME & CITY

* WARRANTY INFORMATION *

It is very important that you read and understand the conditions outlined in the Warranty InformationSheet attached to the outside of the shipping container of your machine.

The Warranty Information Sheetmust be filled out completely and returned to THE CHALLENGE

MACHINERY COMPANY in order for the warranty to be issued for this machine.

Challenge is a registered trademark of

The Challenge Machinery Company 6125 Norton Center Drive Norton Shores MI 49417

Copyright 1997-2012 by The Challenge Machinery Company. All rights reserved. Printed in the U.S.A

8/11/2019 F.254-I-T

4/139

1.0 Introductio

TABLE OF CONTENTS

1.0 Introduction...................... ......................... .......................... ......................... ......................... ...... 2

2.0 Safety ......................... .......................... ......................... ......................... ................................ .... 5

2.1 Precautions....................... ......................... ......................... .......................... .......................... 5

2.2 Power Lockout Procedure ....................... ......................... .......................... ......................... .... 5

2.3 Warning Label Definitions............................ ......................... .......................... ......................... 6

3.0 Maintenance Guide ....................... .......................... ......................... ......................... .................. 8

3.1 Maintenance Adjustments....................... ......................... .......................... ......................... .... 93.1.1 Centering the Backgauge Control Knob............................................ ......................... ....... 93.1.2 Squaring the Backgauge...................... .......................... ......................... ......................... 93.1.3 Proximity Switches.............. ......................... .......................... ......................... ............... 10

3.1.4 Hydraulic Valve Adjustments................. ......................... .......................... ...................... 133.1.5 Clamp Cylinder ....................... ......................... .......................... ......................... ........... 17

3.1.6 Clamp Parallel Rod...................... ......................... .......................... ......................... ...... 18

3.1.7 Backgauge Gibs................................... ......................... ......................... ........................ 19

3.1.8 Lead Screw Adjustment Nuts ........................ .......................... ......................... .............. 20

3.1.9 Backgauge Drive Belt Adjustment ...................... ......................... ......................... .......... 21

3.1.10 Knife Bar Gibs................... ......................... ......................... .......................... ............... 21

3.2 Repair and Replacement................................. .......................... ......................... ................... 233.2.1 Fuses................................. ......................... .......................... ......................... ................ 23

3.2.2 Knife Bar Cylinder....................... .......................... ......................... ......................... ....... 233.2.3 Pilot Check Valve............ ......................... ......................... .......................... ................... 253.2.4 Clamp Return Speed Adjustment ....................... ......................... ......................... .......... 263.2.5 Table Maintenance .......................... ......................... ......................... .......................... .. 26

4.0 Troubleshooting ........................ ......................... .......................... ......................... .................... 28

5.0 Schematics & Parts Lists............................. ......................... ......................... ............................ 32

5.1 Main Assembly Front View........................ ......................... ......................... ....................... 32

5.2 Main Assembly Side View ......................... ......................... ......................... ....................... 36

5.3 Main Assembly Top View...................... .......................... ......................... ......................... .. 38

5.4 Main Assembly Rear View............................. ......................... ......................... ................... 40

5.5 Main Assembly X Model Tables............................. .......................... ......................... .......... 44

5.6 Main Assembly XG/XT Model Table ....................... ......................... .......................... ......... 46

5.7 Main Assembly - Air Table Assembly......................... ......................... .......................... ......... 485.8 Main Assembly - Power Panel Wiring XG/XT - 1 Phase...................... ......................... ........ 505.9 Main Asm. Front View (Rough).............. ......................... ......................... ......................... .. 52

5.10 Main Assembly- Electric Eyes ........................ ......................... .......................... .................. 565.11 Main Assembly- Electric Eyes ........................ ......................... .......................... .................. 585.12 Main Assembly Electric Eyes (X, XG, XT)......... ......................... .......................... ............. 605.13 Main Assembly - Wiring X Model 1ph................ .......................... ......................... ......... 61

5.14 Basic Machine Schematic XG/XT Models......................... ......................... ...................... 62

5.15 Basic Machine Schematic X Models ......................... ......................... .......................... ..... 64

5.16 Power Panel Assembly 305X ...................... ......................... .......................... .................. 66

5.17 Power Panel Asm. 305X (Blower Opt. Wiring) ........................ ......................... ................. 70

5.18 Power Panel Assembly 305X XG/XT Models....................... ......................... ................. 72

5.19 Interconnection Diagram 305X XG/XT Models........................ ......................... ............. 785.20 Interconnection Diagram 305X ........................ .......................... ......................... .............. 80

5.21 Control Console Assembly - 305XG Model........................... ......................... ...................... 805.22 Control Console Assembly - 305X...................... .......................... ......................... .............. 805.23 Control Console Assembly - XT Model - Color LCD....................... ......................... ............. 805.24 Cut Button Assembly (Obsolete).......................................... ......................... ....................... 80

5.25 Cut Button Assembly (Current)... .......................... ......................... ......................... .......... 80

5.26 Kit Ergonomic Touch Switch (Cut Button Option)............................ .......................... ........ 80

5.27 Line Light Assembly.......................... ......................... ......................... ......................... ....... 80

5.28 Air Table Blower Assembly Single Phase ...................... .......................... ......................... 80

8/11/2019 F.254-I-T

5/139

1.0 Introduction

4

5.29 Compressor Assembly.........................................................................................................80

5.30 Backgauge Control Assembly ......................... ......................... ......................... ...................80

5.31 X/XG/XT Troubleshooting ...................... ......................... .......................... ......................... ..80

5.32 Description of Error Messages ........................ .......................... ......................... ..................80

5.33 Sensor Data Abbreviations...................................................................................................805.34 Encoder Cable Assembly 305X - X Models ........................ .......................... .....................805.35 Encoder Cable Assembly 305X XG/XT Models.................................. ......................... ....805.36 Knife Latch Assembly...........................................................................................................80

5.37 Bell-Crank Assembly Clamp..............................................................................................805.38 Hydraulic Manifold Assembly ...................... ......................... .......................... ......................80

5.39 Hydraulic Power Unit Assembly ....................... ......................... ......................... ..................80

5.40 Hydraulic Manifold ......................... ......................... ......................... ......................... ...........80

5.41 Manifold Assembly...............................................................................................................80

5.42 Fuse Charts.........................................................................................................................80

5.43 XG/XT Models Label Power Panel Connection Procedure................ .......................... .......80

5.44 305 X Model Label Power Panel Conn. Procedure. .......................... ......................... ........80

5.45 Warning Label......................................................................................................................805.46 Paper Deflector (Kit Option) ........................ ......................... ......................... .......................805.47 Paper Deflector Assembly....................................................................................................805.48 Extension Tables - 24 x 36 - (Kit Option)............................................................................80

5.49 Extension Air Tables - 24 x 36 (Kit Option).........................................................................80

5.50 Back Gauge Tape Kit...........................................................................................................80

5.51 Electric Eye Kit Instructions (Obsolete)..............................................................................80

5.52 Electric Eye Kit Instructions (Current) ........................ .......................... ......................... .....80

5.53 Jogging Aid Construction Guide...................... ......................... .......................... ..................80

5.54 Converting 305X Series from Three Phase to Single Phase. ........................ ........................80

5.55 Knife Lifter Assembly ......................... ......................... ......................... ......................... .......80

6.0 Safety System Tests ...................... .......................... ......................... ......................... ................80

8/11/2019 F.254-I-T

6/139

2.0 Safe

2.0 Safety

2.1 Precautions

This machine is designed for one-person operation. Never operate the machine with more thanone person.

Safe use of this machine is the responsibility of the operator. Use good judgment and commonsense when working with and around this machine.

Read and understand all instructions thoroughly before using the machine. If questions remain,contact the dealer from which you purchased this machine. Failure to understand the operatinginstructions may result in personal injury.

Only trained and authorized people should operate this machine.

Do not alter safety guards or devices. They are for your protection. Severe personal injury mayresult.

Disconnect power before cleaning or performing maintenance. See Section 2.2 Power LockoutProcedure.

Observe all caution labels and plates on this machine.

Be sure the cutter is properly grounded. Be sure there is sufficient power to operate the cutter properly.

Keep foreign objects off the table and away from cutter blade.

BE EXTREMELY CAREFULwhen handling and changing the cutter knife. Severe lacerations ordismemberment could result from careless handling procedures.

Keep the floor around the cutter free of trim, debris, oil and grease.

When replacing hydraulic parts, loosen the connections slowly to release pressure. Never loosenconnections with the machine running.

If the cutter sounds unusual or operates abnormally, turn it off and consult the troubleshootingsection of this manual. If the problem cannot be corrected, have it checked by a qualified serviceperson.

CRUSH HAZARD, keep hands and fingers from under the clamp while clamping. Use JoggingAid to load paper, and use the backgauge to push paper out before unloading. DO NOT REACH

UNDER THE KNIFE AND CLAMP AREA!

2.2 Power Lockout Procedure

For maximum safety when making adjustments or repairs to your machine, be sure to lock out themain power control switch to which the machine is connected. The switch should be moved to theOFF position and a padlock placed in the loop. The person servicing the machine should hold thekey.

Figure 1

8/11/2019 F.254-I-T

7/139

2.0 Safety

6

2.3 Warning Label Definitions

The following warning labels are found at various locations on your machine. Read and understandthe meaning of each symbol. If a label is lost from the machine, it should be replaced. The itemnumber and location of each label can be found in Section 17.0, Schematics and Parts List.

HAZARDOUS AREA

Disconnect power before cleaning, servicing, or making adjustments not requiringpower. Do not alter safety guards or devices; they are for your protection. Replaceall guards. Do not operate with any guards removed.

SHOCK HAZARD

Disconnect power before removing cover. Replace cover before operation.

SHOCK HAZARD

Disconnect power before removing cover. Replace cover before operation.

SINGLE OPERATOR

Do not operate with more than one person.

8/11/2019 F.254-I-T

8/139

2.0 Safe

!OJO!

This Este simbolo de alerta de seguridad significa OJO ! - IN-STRUCCIONES DE SEGURIDADPERSONAL. Lea las instrucciones porque se refieren a su

seguridad personal. Fall de obedecer las instrucciones que siguen podria resultar en lesionescorporales.

Esta maquina, junto con sus mecanismos de seguridad, esta disenada para ser manejada por UNA SOLA PERSONAa la vez. Jamas debe ser manejada por mas de una persona al mismo

tiempo.

La seguridad es la responsabilidad del operario que usa esta maquina. LEA DETENIDAMENTEel manual de instrucciones y las PRECAUCIONES DE SEGURIDAD

antes de poner a funcionar la cortadora. Pidale a su supervisor una copia.

El manejo de la guillotina debe estar exclusivamente a cargo de personal entrenado y autorizadopara ello.

NO MODIFIQUE LOS MECANISMOS DE SEGURIDAD, estan ahi para su proteccion no debenni modificarse ni quitarse.

DESCONECTE LA CORRIENTE ELECTRICAantes de proceder a hacerle servicio de limpieza,engrasar, o de hacer adjustes que no requieren corriente. Trabe el interruptor en la posicionOFF(apagado); vea Procedimiento para cortar la corriente electrica al pie de esta pagina.

Eche llave a la guillotina y quite la llave cuando la maquina no esta en operacion; vea Corrienteelectrica.

Asegurese de que la guillotina este debidamente a tierra. Vea Conexion de la fuerza electrica.

Verifique el voltaje y asegurese de que este sea suficiente para el debido funcionamiento de laguillotina.

Preste atencion a todas las placas con advertencias instaladas en esta guillotina.

No permita que objetos estranos esten en la mesa o cerca de la cuchilla cortadora.

TENGA SUMO CUIDADOal tocar y cambiar la cuchilla. Heridas severas y hasta desmem-bramiento pueden resultar del manejo sin cuidado o negligente.

El suelo alrededor de la guillotina debe mantenerse despejado y libre de recortes, desperdicios,

aceite y grasa. Al haber la necesidad de reemplazar partes hidraulicas, afloje todas las conexiones poco a poco

para dejar escapar la presion. Jamas debe aflojarse conexiones mientras la maquina este

andando.

Si la guillotina empezara a sonar o trabajar diferentemente a lo acostumbrado, desconectela yconsulte la seccion Troubleshooting (Reparador) de este manual. Si no es posible corregir elproblema, llame a su servicio autorizado para que le examinen la maquina.

PELIGRO DE MACHUQUE- Mantenga manos y dedos fuera de la agarradera mientras sujeta elpapel. Use el calibrador trasero y su rueda de mano para empujar el papel cortado. NO PONGASUS MANOS BAJOLA CUCHILLA O AREA DE LA AGARRADERA.

NO OPERE SIN LAS GUARDAS PROTECTORAS!

OJO ! PRECAUCION - Como proceder para desconectarla corriente electrica.

Para maxima seguridad durante ajustes y reparaciones de su maquina, verifique bien que el interruptor principalde control de corriente al cual la maquina esta conectada, este desconectado. El interruptor deba ser puesto enla posicion OFF (desconectado) y se debe poner un candado en la anilla. La llave del candado debe ser guar-dada por la persona que estara efectuando los trabajos de servicio o de reparacion en la guillotina.

Desconecte la corriente electrica antes de proceder a hacer cualquier ajuste o reparacion o de efectuar el en-grase en cualquier maquina.

8/11/2019 F.254-I-T

9/139

3.0 Maintenance Guide

8


NOTICE

The instructions on the followingpages are for the use of trained

service personnel only!

Attempting to perform repair andreplacement procedures withoutproper training may cause ma-

chine damage or operator injury!PARTS CUSTOMERS: Parts with the express understanding that they are to replace partsfound missing or no longer serviceable on equipment designed and/or manufactured atChallenge. The Challenge Machinery Company assumes no liability for any modification oralteration to any Challenge products, and any such modification or alteration to any Chal-lenge product is not authorized by The Challenge Machinery Company. Any modification oralteration of any Challenge product will void any remaining warranty.

8/11/2019 F.254-I-T

10/139

3.0 Maintenance Gui

3.1 Maintenance Adjustments

3.1.1 Centering the Backgauge Control Knob

The Backgauge Control Knob is coupled with a potentiometer. If the Control Knob is misadjusted, thebackgauge may wander forward or backward.

To adjust the Control Knob, turn the power off and then on and immediately enter Sensor Data Mode.Hold the rubber coupling in the Control Knob Assembly while turning the knob. Adjust the knob until.512 is displayed on the screen. Turn the power of and then on once again.

Figure 2

3.1.2 Squaring the Backgauge

To test the backgauge for squareness, place a small lift of paper against the left side of the back-

gauge (but not against the side guide) and make a cut.

Figure 3

Now, leave the backgauge in the same position, flip the lift over and against the right side of the back-gauge (but not against the side guide). Make another cut to see if any of the stock will trim off. Run

two checks, one starting on the left and moving to the right, the other, moving from the right to the left.Trim in either sequence indicates the backgauge is out of square.

1. As machine wears, make sure the backgauge gibs are set properly first (see BackgaugeGibs), then follow steps 2 through 5.

NOTE: Gib adjustment is not necessary on initial machine setup because they have been ad-justed at the factory.

PAPER

8/11/2019 F.254-I-T

11/139


10

2. Loosen backgauge locking screw (smaller head). Loosen the jam nuts on the backgaugesquaring screws.

Figure 4

3. Back off the squaring screw on the side that the trim occurred and tighten the other.

4. With the squaring screws tight, make another test. Continue to adjust and test until no trimoccurs when testing in either sequence.

5. Tighten the jam nuts and lock screw.

3.1.3 Proximity Switches

These tests require the machine to be operational for checking and adjust-ing. Be very careful that tools and other people are clear of moving parts and that the cutter is notaccidentally operated while adjustments are being made.

Challenge Champion cutters incorporate proximity switches to detect stages of operation. Thesetypes of limit switches have no moving parts and are more reliable than the old style of contactswitches.

NOTE: Adjust the switches in the following order:

1. Kni fe Up/Down Limi t Switches2. Hydraulic Up Limit Switch3. Clamp Up Limit Switch4. False Clamp Sheath Limit Switch

LockingScrew

Squaring Screws

8/11/2019 F.254-I-T

12/139

3.0 Maintenance Gui

CRUSH HAZARD! When the limit switch is actuated, the clamp will returnto the up position. Keep hands and tools clear.

1. Knife Up/Down Proximity Switches

Figure 5

The Knife Up and Knife Down Proximity switches are mounted to a bracket that is attached to theKnife Cylinder (Figure 5). With the power off, set the collar between the proximity switches and thenturn on power. Press cut buttons once to turn on the hydraulic motor. The knife will move to the ab-solute top of its stroke. Move the collar to the top proximity switch until LED turns on, then move it anadditional 1/4 higher and tighten its setscrew. An indicator light on the switch body comes on whenthe switch is actuated (proximity switches must be within 1/8 (3.2mm) to actuate). Check the KnifeDown Proximity switch by going into the Maintenance screen to Knife Adjust and lock the knife in thedown position. Check the distance between the proximity switch and the actuator.

2. Hydraulic Up Proximity Switch

This switch is mounted on the left, rear leg of the base casting (Figure 6 on page 12). An indicatorlight on the switch body comes on when the switch is actuated (proximity switches must be within 1/8(3.2mm) to actuate). The switch senses the extension of the clamp cylinder at the top of its stroke.This stops hydraulic power to the clamp and knife. If the switch is not properly set, the knife andclamp cylinders will be under constant load (indicated by excessive heat and noise).

To adjust:

a. Loosen the bottom lock nut and turn the top lock nut down to raise the switch.

b. Turn on the machine and press the cut buttons once to start the hydraulic motor.

c. The knife and clamp will move to the extreme up position and a load will remain on thehydraulics.

d. When the cylinder has stopped moving, pass a metal object in front of the switch to actu-ate it and take the load off the hydraulics. Keeping pressure on the switch to hold itagainst its mounting bracket, turn the lock nut up to lower the switch until the indicatorlight in the switch comes on. Tighten the lower jam nut.

e. Press the cut buttons to cycle the clamp and check clamp position.

8/11/2019 F.254-I-T

13/139


12

Figure 6

3. Clamp Up Proximity Switch

This switch is mounted inside the rear of the arch casting, Figure 7. It is tripped by the clamp when

the clamp is in the up position. This switch prevents backgauge movement if the clamp is not up. Onmachines equipped with the air table option, it also diverts the air from the table when the clamp isdown to prevent the stock from moving during a cut. This switch is tripped by a actuator on the top ofthe clamp and must be adjusted to within 1/8 (3.2mm) of the face of the switch.

Figure 7

4. False Clamp Sheath Limi t Switch

This switch is mounted on the false clamp sheath on the right side of the machine, Figure 7. It istripped when the false clamp plate is in the sheath. This switch prevents the backgauge from gettingany closer then 2 to the clamp if the false clamp plate is not in the sheath. If the switch is actuated(the false clamp plate is in the sheath) then the minimum cut size is 3/4. To check the switch slidethe false clamp plate into the sheath and check that the light on the switch is on. If the switch needsto be adjusted, move the switch to within 1/8 (3.2mm) from the face of the switch to the metal falseclamp plate.

Hyd. Up Prox-imity Switch

8/11/2019 F.254-I-T

14/139

3.0 Maintenance Gui

Figure 8

3.1.4 Hydraulic Valve Adjustments

Several of the following tests require the machine to be operational forchecking and adjusting. Be very careful that tools and other people are clear of moving parts and thatthe cutter is not accidentally operated while adjustments are being made. Disconnect the power andlock it out, see Safety Precautions, page 8, whenever working on the machine unless the directionsspecifically require the machine to be powered.

For initial setup, adjust the valves in the following order:

1. Main System Relief Valve- 1800 psi2. Kni fe down sequence valve- 1600 psi3. Clamp up relief valve- 400-600 psi4. Pressure reducer valve (X only)- 1400max/400min psi

5. Electronic Clamp Pressure- 1400max/400min psi

NOTE: Pressure settings fluctuate with oil temperature. Set pressures when the oil is hot.

8/11/2019 F.254-I-T

15/139


14

Figure 9

1. Main System Relief Valve (Figure 9)

This valve maintains the overall hydraulic pressure for the entire system. Factory setting: 1800 psi.

Check Procedure:a. Open the left access door on front of the cutter.b. Turn the power on and make a cut to hold the knife down on the cutting stick. Read the

pressure off the main system pressure gauge (front gauge) while the knife is down. If thegauge does not read 1800 psi, an adjustment is needed. You may need to send knifedown in maintenance mode to read the gauge more easily.

To Adjust: Loosen the lock nut on the relief valve. Use an Allen wrench to turn the adjusting screw.

Turn clockwise to increase pressure, counter-clockwise, to decrease pressure.

a. Make a cut and hold the buttons in. Or go to knife down adjustment in maintenancemode to cycle the hydraulics. Adjust the valve screw until you have the correct pressure.

b. Tighten the lock nut while holding the hex wrench in place.

c. Proceed to readjust the other valves.

2. Kni fe Down Sequence Valve (Figure 9)

This valve controls the clamp and knife sequence. It keeps the knife up until after the clamp hasmade contact. It is the upper right valve on the front of the manifold. Factory Setting: 1600 psi.

NOTE: Main System Pressure must be set at 1800 psi before making this adjustment.

Check Procedure:

a. Open the left access door on front of the cutter.

b. Press the cut buttons while reading the pressure on the main system pressure gauge(front gauge). The gauge should read approximately 1600 psi as the knife is movingdown (when bottomed, the gauge will jump to 1800 psi showing the Main System Re-lief Pressure previously set).

c. If correct, proceed to check the Pressure Reducer.

MainSystemGauge

ElectronicClamp Valve

Main SystemRelief Valve

Knife DownSequence

Clamp UpSequence

8/11/2019 F.254-I-T

16/139

3.0 Maintenance Gui

To adjust:a. Loosen the lock nut.

b. Make a cut and hold the buttons in. While reading the main system gauge, adjust thevalve until you have the correct pressure. Clockwise to increase, counter-clockwise todecrease.

c. Tighten the lock nut while holding the hex wrench in place.

d. Proceed to readjust the other valves.

3. Clamp Up Sequence Valve (Figure 9on page 14)

This valve maintains clamp pressure so the clamp remains down until the knife has stopped inthe up position. Factory setting: 400-600 psi.

Check Procedure:a. Open the left access door of the cutter.

b. Press the cut buttons, and while reading the pressure on the main gauge (frontgauge), release them. The gauge should read between 400-600 psi as the clamp isgoing up. There should be no clamp movement until the knife is stopped in the upposition.

c. If correct, proceed to check the Pressure Reducer.

To Adjust:a. Remove the protective cap and loosen the lock nut on the clamp up sequence valve.

b. Make a cut, then release the buttons. Read the main gauge as the clamp is return-ing. Adjust the valve for a reading of 400-600 psi.

c. Tighten the lock nut while holding the hex wrench in place and replace the protectivecap.

d. Proceed to readjust other valves.

4. Manual Pressure Reducer Valve- (X only)

This valve, Figure 10 on page 16, limits the amount of pressure to the clamp system. Factory setting:1000 psi (1400max/400min).

To Check: With the hydraulic access door open, activate the cut buttons and read the pressure off

the clamp gauge (rear gauge). It should read 750 psi for average cutting purposes.

To Adjust:1. Loosen the lock knob. There are two knobs, one behind the other. The outer is the adjusting

knob. The inner is the lock knob.

2. Push the cut buttons and check the reading on the clamp gauge (rear gauge) when the clampis on the table and the knife is coming down.

8/11/2019 F.254-I-T

17/139


16

3. Turn the Pressure adjusting knob clockwise for MORE pressure, counter-clockwise for LESS.

DO NOT set the clamp pressure below 400 psi. Severe lacerations or dis-memberment could result! The knife and clamp system will lose sequence settings below 400 psi

and the knife could come down before the clamp.

4. Make another cut and check the pressure gauge. Adjust the pressure to your cutting applica-tion (See Operator Tips or Knives sections).

5. Tighten the locking knob.

Figure 10

1. Electronic Clamp Control Valve- (XG)

The electronic clamping control allows the convenience of changing the clamp pressure at the controlconsole. The pressure is controlled by use of the up and down arrow keys, 0 being the lowest, 15 thehighest; and is indicated in the upper right hand corner of the display. See below:

Adjustment of the Electronic Valve:a. To adjust the pressure range, enter the Maintenance Mode and choose Diagnostic.

b. To adjust the pressure, select Clamp Adjust. See the next screen on page 86:

c. Setting the Maximum Pressure: Perform a cut cycle, after the clamp has contactedthe table and while the knife bar is coming down, read the pressure on the right handpressure gauge. It should be set at 1400 p.s.i. If not, correct by using the up and

ClampGauge

Pressure AdjustKnob

LockKnob

5.000in

DIAGNOSTICError CodeSensor DataClear MemoryClamp Adjust

Select & press enterA) Maint C) SendB) Job D) Exit

8/11/2019 F.254-I-T

18/139

3.0 Maintenance Gui

down arrow keys. When finished, choose D), to exit and go to the minimum pressureset up seen shown below:

d. Setting the Minimum Pressure: Perform a cut cycle, after the clamp has contactedthe table and while the knife bar is coming down, read the pressure on the right handpressure gauge. It should be set at 400 p.s.i. If not, correct by using the up and

down arrow keys. When finished, choose C), to return to the Send mode, or D) Exit toreturn to Diagnostics.

3.1.5 Clamp Cylinder

If the clamp piston bottoms in the cylinder before the clamp makes contact with the table, or if theclamp does not make full travel on the up stroke, the clamp cylinder may need adjustment. Theclamp cylinder is located inside the left base casting leg behind the left front door (Figure 11, on page18).

5.000Set Maximum>

Press /\ to Increase

Press \/ to Decrease

A) Main C) SendB) Job D) Exit

5.000Set Minimum>

Press /\ to Increase

Press \/ to Decrease

A) Main C) SendB) Job D) Exit

ClampCylinder

8/11/2019 F.254-I-T

19/139


18

Figure 11

To adjust:1. Turn on machine. Start the hydraulic motor by pressing both cut buttons simultaneously.

Turn off the machine.

2. DISCONNECT THE POWER AND LOCK IT OUT! (See Power Lockout procedure, page 5).

3. Loosen the jam nut.

4. Use the flats on the clamp cylinder shaft to turn the shaft into or out of the clevis as required,(Figure 8). (In decreases, out increases height.) The clamp should be set to 4 above thetable.

Figure 8

5. Retighten the jam nut securely.

3.1.6 Clamp Parallel Rod

If the clamp is not parallel with the table:

1. DISCONNECT THE POWER AND LOCK IT OUT! (See Power Lockout procedure, page 5.)

2. Loosen the jam nuts on each end of the clamp connecting rod, (Figure 9 & Figure 14). (Note:the left jam nut has left hand threads.)

Figure 9 & Figure 10 LH & RH End o f Rod

JamNut

JamNut

Clevis

Jam Nut

Wrench Flat

8/11/2019 F.254-I-T

20/139

3.0 Maintenance Gui

3. Using the flats on the end exposed below the base casting, (Figure 9 & 14), turn the connect-ing rod and align the clamp with the table. Place a long strip of paper under each end of theclamp. Push the cut buttons and when the clamp contacts the table, attempt to pull the stripsout. The clamp should be adjusted so neither strip pulls out.

4. Retighten the jam nuts securely.

3.1.7 Backgauge Gibs

If you are having trouble keeping the back-gauge square, check for backgauge side play. Positionthe backgauge approximately 2 (50-55mm) from the rear of the table and turn off power.

Remove the rear table cover. From the back, hold each end of the backgauge and try pulling oneend while pushing the other to rock it side to side. If there is noticeable side-to-side play in the back-gauge, the gibs will need adjusting. Check for play at various positions on the table, (Figure 11).Note: there will be some front to rear movement between the backgauge nut and screw.

Figure 11

The backgauge has two gibs that ride on an iron rail underneath the table, (Figure 12). These are ad-justed with setscrews, which are held in position with jam nuts.

Figure 12

To adjust:1. Run the backgauge back to 23 (600mm) and disconnect the power.

2. Always adjust the side gib first. Loosen all jam nuts and adjusting screws then tighten thefront and rear screws.

3. Pull each end of the backgauge and try to rock it side to side as before to check for play.

4. Continue to adjust these two screws until there is no play and the hand-wheel still turns easily(X only).

Set Screws& Jam Nuts

Rail

8/11/2019 F.254-I-T

21/139


20

5. Lock the screws in place with the jam nuts.

6. Snug up the middle two screws and lock in place with the jam nuts.

7. Snug up the bottom gib adjusting screws finger tight and lock in place with the jam nuts.

8. Run the backgauge back and forth to make sure it does not bind. Readjust if necessary.

9. Replace the rear table cover.

10. Check the backgauge squareness.

3.1.8 Lead Screw Adjustment Nuts

If play is noted in the forward pillow block and thrust bearings, take up the play in the adjustment nutsby:

1. Loosening the lead screw jam nuts, Figure 13 (X) & Figure 14 (XT/XG) on page 20.

2. Snug up the inner nut to eliminate any play.

3. Tighten the nuts against each other.

4. Check the socket head bolts in the pillow block to make sure they are also tight.

Figure 13 X Model Jam Nut Location

Figure 14 XG Model Jam Nut Location

8/11/2019 F.254-I-T

22/139

3.0 Maintenance Gui

2

3.1.9 Backgauge Drive Belt Adjustment

If the backgauge motor runs but the backgauge does not move or slips, the belt may need adjust-ment, Figure 15.

Figure 15

To adjust the belt:1. Turn off the machine, DISCONNECT THE POWER AND LOCK IT OUT! (See Power Lock-

out procedure, page 5.)

2. Remove the drive belt cover guard at the rear of the table.

3. Loosen the four socket head screws holding the motor to the mounting plate.

4. Slide the motor down to put more tension on the belt, or lift it up to reduce tension for remov-ing belt.

5. If belt cannot be tightened, replace with a new belt.

6. Adjust the tension of the belt so that there is a 1/2-3/4 (10mm) flex remaining and tightenthe mounting plate socket screws.

7. Replace the belt guard cover.

8. Reconnect the power to the machine.

3.1.10 Knife Bar Gibs

The knife bar gibs are two steel backed UHMW plates on either side of the arch that guide and holdthe knife as it cuts. If adjusted too tight the knife may not come down, or scoring could damage thegibs and knife bar. If too loose, you could get uneven or inaccurate cuts.

WARNING: Knives are heavy and very sharp (even after use). Severelacerations could result. Follow all safety precautions and knife changing instructions fromthe Knives section o f this manual.

8/11/2019 F.254-I-T

23/139


22

There are three, socket set screws with jam nuts on each side of the arch that adjust the gibs, (Figure20). These should be adjusted only with the knife bar directly behind the screws being tightened.

Figure 20

To adjust:1. Start the machine and make a cut. When the knife is half way down, have someone press

the stop button. The knife bar should be stopped half way across the gibs.

2. Loosen all (6) jam nuts on the gib adjusting screws and back the screws out 1/2 turn.

3. Adjust center (2) screws until snug - not tight to eliminate the air gap between the knife barand gib. Tighten those (2) jam nuts.

4. Place the machine into knife down adjustment mode. See Operating instructions for yourmachines model.

5. Adjust the bottom two screws the same way the middle screws were adjusted. Tighten thejam nuts.

6. Start the machine. The knife should return to the up position. Shut the machine off.

7. Adjust the upper (2) gib adjusting screws and tighten the jam nuts.

8. Turn the power back on and cycle the knife several times. Recheck the gibs (repeat steps 2-6as necessary).

9. Dont over-tighten the gibs.

10. If the knife bar and gibs get scored, remove only the burrs by scraping and then sandingsmooth.

8/11/2019 F.254-I-T

24/139

3.0 Maintenance Gui

2

3.2 Repair and Replacement

3.2.1 Fuses

FIRE HAZARD. Replaceonly with same type and rating fuse.

Figure 16

The Champions each have a set of fuses. The fuses are located inside the main power box, (Figure16). Check the label inside the cover for correct ratings for these fuses. Labels are reproduced withthe drawings at the back of this manual in case those on the cover may be damaged or illegible. (Seepages 80, 80, & 80.)

3.2.2 Knife Bar Cylinder

Replacing the Knife Bar Cylinder:1. Remove the knife from the cutter (see Knife, Installation and Set Up).

2. Place a 3 (60mm) lift of paper under the clamp only to hold it up and out of the way of theknife bar. Then place a 3 (1 meter) long 2x4 board flat side down under the right end of theknife bar. This will be used for leverage on the knife bar when removing and reinstalling theknife bar pin.

3. Lock the clamp and knife down by following instructions in the Operator Controls section foryour particular model of machine.

4. Turn off the main power disconnect switch. DISCONNECT POWER AND LOCK IT OUT!

See page 5.

Loosen connections slowly to bleed off any trapped pressure!

5. Place a pan underneath the cylinder and gradually loosen and remove the hydraulic connec-tions. Loosen the connections slowlyto bleed off any trapped pressure.

8/11/2019 F.254-I-T

25/139


24

Figure 22

6. Remove the clevis pin. E-style retaining rings on each side of the pin can be removedthrough the access panel in the side of the arch casting. The pin has a 1/4-20 tapped hole init to aid removal and a clearance hole in the front of the arch provides access to knock the pinout of the knife bar, (pg. 95, fig. 65). Use the board to block up the knife bar and to releasepressure from the pin to make it easier to remove.

7. Now, remove the pin retainer and the Tru-arc retaining ring from the lower mounting pin hold-ing the cylinder to the base.

8. Remove the old cylinder. With the shaft of the old cylinder bottomed out, note the dimensionbetween the top of the cylinder body and the bottom of the cylinder clevis. Also note the ap-proximate position of the proximity switch actuator. Transfer the proximity switch actuator,the clevis lock nut, and the clevis onto the new cylinder and insert it into position on the cut-ter.

9. Reinstall the base pin, Tru-Arc retainers, and the pin retainer.

10. Install the upper pin to connect the cylinder to the knife bar and replace the retaining rings.

11. The cylinder shaft can be threaded into the clevis to adjust the position of the knife bar.When properly adjusted, the distance from the top of the knife bar recess to the table with theknife in the down position should measure 4-1/8 (103mm), (Figure 18).

Figure 17

12. Lock the jam nut securely in place.

13. Reconnect the hydraulic hoses.

Clevis

JamNut

-20 Tapped Hole E-Ring

Clevis

8/11/2019 F.254-I-T

26/139

3.0 Maintenance Gui

2

CRUSH HAZARD! Knife and clamp will return to the up position whenthe key is turned on and the cut buttons are pressed for the first time. Keep hands and toolsaway.

Figure 18

14. Reconnect the power to the cutter and turn main power on.

15. Adjust the Knife up proximity switch actuator. Press the cut buttons once to turn on the hy-draulic motor and raise the knife and clamp. Allow machine to run for a few minutes to workthe air out of the system.

16. See Knife Installation and Set up for reinstalling the knife.

3.2.3 Pilot Check Valve

The Pilot Check Valve on the knife cylinder (Figure 19) helps to hold the knife in the up position. If itbecomes stuck or plugged, the clamp will come down but the knife will remain in the up position.

Figure 19

To check:1. Follow the knife changing procedures to remove the knife blade and then block the knife bar

in the up position.

Clamp

KnifeBar

Arch

Table

4-1/8

Pilot CheckValve

8/11/2019 F.254-I-T

27/139


26

2. Turn the main-power disconnect switch to the off position, DISCONNECT THE POWER ANDLOCK IT OUT! (See Power Lockout Procedure, page 5.)

3. Place a pan underneath the valve and slowly loosen the pilot valve connections to bleed offany pressure.

4. Remove the check valve and hoses from the knife cylinder. Replace the hose fitting attachedto the cylinder with the two 900fittings on the check valve. (The smaller fitting goes on thetop port.) Reconnect the hoses.

5. Reconnect the power and run the machine.

6. If the knife cycles without the valve in line, replace with a new check valve.

3.2.4 Clamp Return Speed Adjustment

The clamp return speed can be adjusted if it becomes too sluggish or too fast. This adjustment ismade on the air cylinder that brings the clamp down. To make this adjustment, remove the rear archcover. Turn the lower flow control on the air cylinder clockwise to decrease the return speed of theclamp. Turn the flow control counter-clockwise to increase the return speed of the clamp. The clampshould be adjusted such that it returns fast but does not bounce at the top of the stroke.

The clamp down speed can be adjusted to personal preference. Adjust the clamp down speed usingthe upper flow control valve on the upper end of the cylinder (rod end).

3.2.5 Table Maintenance

The table of a paper cutter requires periodic maintenance to remove surface oxidation. Polishing isalso required to provide a smooth surface for paper to move freely. The frequency of this mainte-nance will be determined by a number of factors. Among these are the humidity, environmental dust,handprints, liquid spills, and type of paper stock. We recommend the use of the Challenge CutterCare Ki t P/N 16077for of your table care needs.

To prepare a new machines table, use the following instructions.

1. Remove the rust-protective coating from the table with a solvent.2. Remove all solvent residues from the table with a dry cloth. Continue until the cloth shows no

sign of residue.3. Apply a light coating of an SAE 10-weight non-detergent motor oil or equivalent to the table and

allow it to penetrate for at least one hour.4. Remove all excess oil from the table with paper toweling (not cloth) until the paper towel you are

using shows no sign of oil.

5. Apply a paste wax (Challenge P/N 16078) to the table to seal the pores of the metal.

Note: Do not use a wax that contains a cleaning compound on the table. The cleaner contains mi-croscopic abrasive particles that will cause wear between the table and the bottom of the backgauge.

A silicone spray (Challenge P/N 16079) will show the same type of wear as the cleaner if the excesssilicone is not removed. If the excess is not removed, the silicone spray has a substance that holdsthe silicone to the surface it is sprayed on that causes a black, gummy build-up under the backgauge.If a silicone spray is used, paper toweling must be used to remove the excess to prevent this wearand build-up.

To clean surface oxidation from a table, follow the procedure below:

8/11/2019 F.254-I-T

28/139

3.0 Maintenance Gui

2

1. Spray Rust-B-Gone (Challenge P/N 16080) on the table and allow it to dissolve the rust. Thenremove it with paper toweling. Or, pour a small quantity of SAE 10-weight motor oil onto the ta-ble. Using a Scotch-Brite Pad or a 400 grit sand paper, polish the table following the grain ofthe metal until all oxidation is removed to your satisfaction.

2. Remove all of the oil from the table until the cloth you are using shows no sign of residue.3. Apply a light coating of an SAE 10-weight non-detergent motor oil or equivalent to the table and

allow it to penetrate for at least one hour.4. Remove all excess oil from the table with paper toweling (not cloth) until the paper towel you are

using shows no sign of oil.

5. Apply a paste wax (Challenge P/N 16078) to the table to seal the pores of the metal.

Note: Do not use a wax that contains a cleaning compound on the table. The cleaner contains mi-croscopic abrasive particles that will cause wear between the table and the bottom of the backgauge.

A silicone spray (Challenge P/N 16079) will show the same type of wear as the cleaner if the excesssilicone is not removed. If the excess is not removed, the silicone spray has a substance that holdsthe silicone to the surface it is sprayed on that causes a black, gummy build-up under the backgauge.If a silicone spray is used, paper toweling must be used to remove the excess to prevent this wearand build-up.

8/11/2019 F.254-I-T

29/139

4.0 Troubleshooting

28

4.0 Troubleshooting

Never work on this machine with the power on unless the instruc-tions say the machine power must be on. Lock the power off at the wall disconnect switch.

See Power Lockout Procedure, page 5.

WONT START1. Fuse blown 4. Cut button defective2. Starter is defective 5. Check error codes3. Loose plug or wire

CUT BUTTONS PUSHED- MACHINE SHUTS OFF1. Knife and clamp are out of sequence. Turn off power and turn back on.2. Check clamp and knife up limit switches.3. When cutting a full pile, the clamp up limit switch does not break contact, either adjust limit switch

or cut down on pile height.4. Defective circuit board

CUT BUTTONS ACTIVATED- WONT CUT1. A cut button is defective.2. Motor wired wrong, going in opposite direction of the arrow sticker on the motor3. Pilot check on the knife cylinder is defective4. Sequence valve pressure is set too high5. Either down solenoid in valves inoperative6. Knife up limit switch is not properly adjusted7. Defective circuit board

ERRATIC OPERATION- POWER LOSS1. Low hydraulic oil level2. Debris in relief valve

3. Defective pump4. Oil bypassing clamp cylinder seals

CLAMP WONT OPERATE1. Bind in linkage or gibs2. Clamp pressure reducer valve set too low3. High pressure solenoid defective4. Relief valve defective5. Clamp return spring defective

CLAMP WONT HOLD PRESSURE1. Clamp cylinder seals worn2. Pressure valve setting too low3. Clamp not parallel to table

CLAMP WONT BOTTOM1. Clamp cylinder out of adjustment2. Clamp return spring broken or out of adjustment

CLAMP NOT PARALLEL TO TABLE1. The clamp connecting rod is out of adjustment.

8/11/2019 F.254-I-T

30/139

4.0 Troubleshooti

2

CONCAVE CUTTING- ENDS WIDE, CENTER NARROW1. Excessive moisture at edges of paper2. More ink on edges of lift

CONCAVE CUTTING- VARIATION OF TOP AND BOTTOM1. Soft stock not firmly clamped2. Knife is dull or ground incorrectly3. Knife bar gibs loose4. Air in stock when clamped, pulls away from backgauge5. Clamp not parallel to table

INCONSISTENT STOPPING OF KINFE IN UP POSITION1. Bind in knife linkage or gibs2. Up sequence valve not properly adjusted3. Knife links worn

HESITATION OF KNIFE1. Dull knife2. Seals worn in knife or clamp cylinder3. Defective pilot check on knife cylinder

4. Knife links worn

KNIFE WONT RETURN1. Defective high pressure valve2. Directional valve(s) stuck in3. Up sequence pressure too low

CLAMP WONT RETURN1. Up sequence pressure too high2. Bind in clamp linkage or gibs3. Clamp not parallel to table4. Clamp return spring defective

KNIFE DRIFTS DOWN1. Knife bar gibs out of adjustment2. Defective pilot check on knife cylinder3. Defective seals in knife cylinder4. Knife latch out of adjustment

KNIFE STOPS IN STOCK1. Knife dull2. Relief valve defective3. Pressure control valve clogged or defective4. Knife cylinder seals worn5. Clamp cylinder seals worn6. Motor stalling due to low voltage or too small wire to machine

NOISY AND SLUGGISH HYDRAULIC SYSTEM1. Cylinder seals worn on clamp or knife2. Low on hydraulic fluid3. Worn spline coupling in motor/pump

INACCURATE CUTTING1. Backgauge not square2. Knife bar has play- tighten gibs3. Backgauge gibs loose

8/11/2019 F.254-I-T

31/139

4.0 Troubleshooting

30

4. Dull knife5. Clamp not parallel to table6. Accuracy not set correctly

BACKGAUGE SPEED ERRATIC1. Oil on pulley belt2. Belt/pulley loose

BACKGAUGE MOVEMENT ERRATIC1. Backgauge gibs loose or binding on table way (rail under table)2. Backgauge nut binding on leadscrew, screw bent or dirty3. Problem with electrical drive component4. Defective circuit board

DRAWING OF STOCK1. Dull knife2. Low clamp pressure3. Hydraulic fluid low4. Air in lift- reduce pile height5. Clamp not parallel to table

SLOW KNIFE1. Defective seals in clamp cylinder2. Defective pilot check valve on knife cylinder3. Pump not achieving full pressure4. Main system or clamp pressure reducer is by-passing fluid

8/11/2019 F.254-I-T

32/139

4.0 Troubleshooti

3

NOTES

8/11/2019 F.254-I-T

33/139

5.0 Schematics & Parts Lis ts

32

5.0 Schematics & Parts Lists

5.1 Main Assembly Front View

47500 Sht. 1 of 16, Rev. X

8/11/2019 F.254-I-T

34/139

5.0 Schematics & Parts Lis

3

Main Assembly Front View47500 Sht. 1 of 16, Rev. XNO. PART NO. DESCRIPTION OF ACCESSORIES QTY

1 S-1781-116 LABEL- WARNING (XD/XG/XT ONLY) 1

2 4506 STUD - CLAMP 2

3 47097 DOOR ASM. - R.H. FRONT 1

4 47033-3 ENCLOSURE - FRONT 1

5 47163 GASKET 6

6 H-465-1 MANIFOLD ASSEMBLY REF.

7 S-1781-11 LABEL - CAUTION (NON-EURO ONLY) 1

7 S-1781-35 LABEL - CAUTION (EURO MACH. ONLY) 1

8 47101 LATCH - FRONT ENCLOSURE 2

9 EE-2149-9 TABLE LIGHT ASSEMBLY- ON/OFF SWITCH 1

10 S-1781-16 LABEL - CAUTION 1

11 8815 WASHER - KNIFE SCREWS 6

12 47507 KNIFE 2

13 4171 CUT STICK 1

14 A-9121 CUT PLATE 215 4503-3 LINK - KNIFE BAR 2

16 E-2196 PLUG - HOLE 3

17 4518 PIN - KNIFE LINK 2

18 S-845 LIGHT - TABLE 1

19 S-1781-11A LABEL - CAUTION (NON-EURO ONLY) 2

19 S-1781-35 LABEL - CAUTION (EURO MACH. ONLY) 2

20 EE-2832-1 SWITCH ASSEMBLY- CUT BUTTON 1

21 4449 KNIFE ADJUSTING SCREW 2

22 S-1193-75 "E" RING - 3/4 2

23 S-1087-1 PIN - ROD END 1

24 EE-2830 SWITCH ASSEMBLY- MAIN DISCONNECT 1

25 4501-4 KNIFE BAR ASSEMBLY- 305 1

26 E-2196-11 PLUG - HOLE 2

27 S-1694 TYRAP 3

28 S-1781-25 LABEL - INSTRUCTION 1

29 47173-1 DOOR ASM. - L.H. FRONT 1

30 H-437 CHECK VALVE ASSEMBLY REF.

31 H-433-1 TUBE ASSEMBLY - KNIFE CYL. PILOT REF.

32 H-435 TEE - MALE RUN 1

33 S-1350-2 BUSHING - CABLE STRAIN RELIEF 1

34 11145-1 RIVET - 3/16 4

35 EE-2823-1 CONTROL CONSOLE- SPACER "XG" 1

35 EE-2850-1 CONTROL CONSOLE- SPACER "X" 135 EE-2998-4 CONTROL CONSOLE- SPACER "XT" 1

36 47502 BRACKET- CONSOLE 2

37 4505 GIB - KNIFE BAR 2

38 S-1864-2 CAPTIVE RET. DEVICE- #10 2

39 EE-2882 ELECTRICAL PANEL - SPACER 1

39 EE-3170 ELECTRICAL PANEL - NON-SPACER "X" 1

8/11/2019 F.254-I-T

35/139


34

Main Assembly Front View47500 Sht. 1 of 16, Rev. X

NO. PART NO. DESCRIPTION OF ACCESSORIES QTY

40 S-1781-52 LABEL - POWER CONN. PROC. - SPACER 1

40 S-1781-161 LABEL - POWER CONN. PROC. - "X" 1

41 47252 FIBER BOARD - KNIFE SLIDE 1

42 47645-1 CLAMP COMPRESSOR ASSEMBLY 1

43 S-1781-34 DECAL - EXTENSION TABLES 2

44 H-504 KIT- HYDRAULIC MANIFOLD 1

45 H-203-33 VALVE- PRESSURE REDUCING, ELEC. (SPACER) REF.

45 5136 VALVE- PRESSURE REDUCING, MANUAL (X) 1

46 47568-1 ASSEMBLY- KNIFE LATCH 1

47 47504 BRACKET- KNIFE BAR KEEPER 1

48 E-2196-17 PLUG- HOLE 4

49 40016-8 VIBRATION ABSORBER 4

50

51 H-6940-416 SCREW - 1/4-20 X 1" FT. PT. SET 852 H-6975-404 SCREW - 1/4-20 X 1/2 NYLOK CUP PT. SS 2

53 H-6918-608 SCREW - 3/8-16 X 1" SOC. HD. 6

54 H-6910-102406 SCREW - #10-24 X 3/4 BUTT. HD. 2

55 H-6913-606 SCREW - 3/8-16 X 3/4 HEX 4

56 H-6953-856 SCREW - 1/2-13 X 3-1/2 OVAL PT. SOC. SET 6

57 H-6910-102404 SCREW - #10-24 X 1/2 BUTT. HD. 15

58 H-6910-102408 SCREW - #10-24 X 1" BUTT. HD. 2

59 H-6910-83204 SCREW - #8-32 X 1/2 BUTT. HD. 2

60 H-6897-102403 SCREW - #10-24 X 3/8 NYLOK FL HD.SOC.CAP 2

61 H-7324-8 WASHER - 1/4 INT. TOOTH 14

62 H-7324-#10 WASHER - #10 INT. TOOTH 15

63 H-7324-#8 WASHER - #8 INT. TOOTH 2

64 H-7327-12 WASHER - 3/8 MED. LOCK 8

65 H-6910-102403 SCREW - #10-24 X 3/8 BUTT. HD. 10

66 H-6424-4 NUT - 1/4-20 HEX 12

67 H-6424-6 NUT - 3/8-16 HEX JAM 2

68 E-2883 ANCHOR - TIE WRAP 3

69 H-7002-8 NUT - 1/2-13 HEX JAM (BLACK) 6

70 H-6423-#8 NUT - #8-32 HEX 2

71 H 6910-405 1/4-20 X 5/8 BUTT. HD. 2

72 H-6913-605 SCREW- 3/8-16 X 5/8 HEX HD. 2

73 H-6923-44012 SCREW- #4-40 X 3/4 RD. HD. 2

74 H-7324-#4 WASHER- #4 INT. TOOTH 375 H-6423-#4 NUT- #4-40 HEX 2

76 S-1781-11 LABEL- CAUTION 1

77 K-47548 TOOL KIT- 305 X 1

77 K-47547 TOOL KIT- 305 XD/XG 1

78 H-7321-#10 WASHER-#10 SAE FLT. PLT'D 4

79 H-7321-6 WASHER-3/8 SAE FLT. 4

8/11/2019 F.254-I-T

36/139


3

Main Assembly Front View47500 Sht. 1 of 16, Rev. X


80

81 H-6910-504 SCREW- 5/16-18 X 1/2 BUT HD 4

82 E-2196-24 HOLE PLUG - 3/8 SHORTY 3

83 47617 FALSE CLAMP PLATE SHEATH ASM. 1

84 H-7324-10 WASHER-5/16 INTERNAL TOOTH 4

85 H-7321-5 WASHER-5/16 SAE FLT. 4

86 H-7327-10 WASHER-5/16 MEDIUM LOCK 4

87 H-6417-5 NUT- 5/16-18 HEX 4

88 H-6910-404 SCREW- 1/4-20 X 1/2 BUT HD 1

89 H-6423-4 NUT- 1/4-20 HEX KEP 1

90 S-1781-42 LABEL- GROUND 1

91 EE-3210 CABLE ASM- COMPRESSOR POWER REF.

92 49249 BACKGAUGE CONTROL ASSEMBLY 1

93 H-6910-604 SCREW- 3/8-16 X 1/2 BHC 2

8/11/2019 F.254-I-T

37/139


36

5.2 Main Assembly Side View

47500 Sht. 2 of 16, Rev. L

8/11/2019 F.254-I-T

38/139


3

Main Assembly Side View47500 Sht. 2 of 16, Rev. L

8/11/2019 F.254-I-T

39/139


38

5.3 Main Assembly Top View

47500 Sht. 3 of 16

8/11/2019 F.254-I-T

40/139


3

Main Assembly- Top View47500 Sht. 3 of 16

8/11/2019 F.254-I-T

41/139


40

5.4 Main Assembly Rear View

47500 Sht. 4 of 16, Rev. N

8/11/2019 F.254-I-T

42/139


4

Main Assembly Rear View Parts List47500 Sht. 4 of 16, Rev. N


1 47519 BRACKET - KNIFE PROX. 1

2 S-1781-15 LABEL - "HAZARDOUS MOVING PARTS" 1

3 EE-2848 CABLE ASM.- LCD BACK LITE 1

4 7032-M TRIM- PLASTIC (9 FT. & 37.5" LONG) 1

5 S-1350-16 BUSHING 4

6 S-1694-2 TYRAP- #10 1

7 EE-2839-2 CABLE ASM.- LINE LIGHT 1

8 47552 COVER- REAR BASE, L.H. 1

9 47050 COVER- BASE, R.H. REAR 1

10

11 47570 COVER- REAR BASE, MAIN 1

12 47171 BRACKET- CLAMP PROX. SWITCH 1

13 47006-2 PLATE ASM.- FALSE CLAMP 1

14 S-1244 PIN- LOCK 215 S-1861 SHIM 2

16 4509-1 BAR CLAMP GUIDE 2

17 47001 COVER- REAR ARCH 1

18 47557-1 AIR CYLINDER ASSEMBLY 1

19 47522 CLAMP 1

20 47267 BRACKET- HYDRAULIC DAMPER 1

21 EE-2834 CABLE ASM.- JUNCTION BOX REF.

22 H-230-6 ELBOW- 90%%D "O" RING TO TUBE 2

23 E-1152-35 SPACER- STAND OFF 1

24 E-1152-36 SPACER- STAND OFF 5

25 47571 BRACKET- REAR COVER 4

26

27 47268 PIN- HYDRAULIC DAMPER 1

28 4508 CLAMP- GUIDE BAR 2

29 4507-1 PIN- KNIFE BAR LINK 2

30 E-2626-6 TERMINAL BLOCK- 6 POLE 1

31 P-303 1/4 VINYL TUBING 58"

32 E-2883 ANCHOR- TYRAP 1

33 S-1694 TYRAP 1

34 47195 BRACKET- ARCH JUNCTION 1

35 S-1864-2 CAPTIVE RETAINING DEVICE 4

36 S-1864-3 CAPTIVE RETAINING DEVICE 6

37 47019-1 GUIDE- REAR, R.H. 138 47020-1 GUIDE- REAR, L.H. 1

8/11/2019 F.254-I-T

43/139


42

Main Assembly Rear View Parts List47500 Sht. 4 of 16, Rev. N


39 4441-1 PAPER GUIDE 1

40

41 E-2186-7 CLAMP- WIRE HARNESS (PROGRAMMABLE ONLY) 2

42 S-1694-2 TIE- CABLE (#10) 1

43 S-1781-61 LABEL - KNDN 1

44 S-1781-62 LABEL - KNUP 1

45 H-6417-6 NUT- 3/8-16 HEX (USE AS SPACERS) 2

46 S-1781-63 LABEL - CLDN 1

47 S-1781-64 LABEL - CLUP 1

48 47528 LIMIT SWITCH ACTUATOR- CLAMP "UP" 1

72 H-7327-12 WASHER- 3/8 LOCK 8

73

7475 H-7324-#10 WASHER- #10 INT. TOOTH 14

76 S-1193-25 "E" RING- 1/4 2

77 H-7324-#4 WASHER- #4 INT. TOOTH 2

78 H-6922-44012 SCREW- #4-40 X 3/4 FLAT HD. 2

79 H-6423-#4 NUT- #4-40 HEX 2

80

81

82H-6910-102403 SCREW- #10-24 X 3/8 BUTT. HD. 12

83 H-6951-406 SCREW- 1/4-20 X 3/8 S.S. NYLOC 3

84 H-6910-403 SCREW- 1/4-20 X 3/8 BUT HD 7

85 H-7324-8 WASHER- 1/4 INT. TOOTH 2

89 H-6910-404 SCREW- 1/4-20 X 1/2 BUTT. HD. 6

90H-6910-102404 SCREW- #10-24 X 1/2 BUTT. HD. 16

91H-6910-102406 SCREW- #10-24 X 3/4 BUTT. HD. 2

92 E-2743 WIRE - #18 GA. GRN/YEL EURO MTW 5" LONG 1

93 E-1214-8 CONNECTOR - #10 INS. RING (16-22 GA.) 1

94 H-6918-608 SCREW- 3/8-16 X 1" SOC. HD. 20

95 H-6918-606 SCREW- 3/8-16 X 3/4 SOC. HD. 2

96 H-6910-408 SCREW- 1/4-20 X 1" BUTT. HD. 1

97H-6903-102404 SCREW- #10-24 X 1/2 BUTT. HD., NYLOC 2

98 S-1781-16 LABEL- CRUSH HAZARD 1

99H-21S-375-1000 ROLL PIN- 3/8 X 1" 1

100 S-1781-12 LABEL- SHOCK HAZARD, ELECTRICAL 1

8/11/2019 F.254-I-T

44/139


4

Notes

8/11/2019 F.254-I-T

45/139


44

5.5 Main Assembly X Model Tables

47500 Sht. 5 of 16 Rev. D

8/11/2019 F.254-I-T

46/139


4

Main Assembly X Model Tables47500 Sht. 5 of 16 Rev. D

8/11/2019 F.254-I-T

47/139


46

5.6 Main Assembly XG/XT Model Table

47500 Sht 6 of 16 Rev. H

8/11/2019 F.254-I-T

48/139


4

Main Assembly XG/XT Model Table47500 Sht 6 of 16 Rev. H

8/11/2019 F.254-I-T

49/139


48

5.7 Main Assembly - Air Table Assembly

47500 Sht. 7 of 16 Rev. E

8/11/2019 F.254-I-T

50/139


4

Notes

8/11/2019 F.254-I-T

51/139


50

5.8 Main Assembly - Power Panel Wiring XG/XT - 1 Phase

47500 Sht. 8 of 16 Rev. D

8/11/2019 F.254-I-T

52/139

8/11/2019 F.254-I-T

53/139


52

5.9 Main Asm. Front View (Rough)

47500 Sht. 11 of 16 Rev. G

8/11/2019 F.254-I-T

54/139


5

Main Assembly Front View (Rough)47500 Sht. 11 of 16 Rev. G


1 47630 CUT STICK STOP 1

2

3 47529 CLEVIS- CLAMP CYLINDER 1

4 47172-1 ACTUATOR- CLAMP PROXIMITY 1

5 H-431-2 CYLINDER ASM.- CLAMP 1

6 47520 BASE 1

7

8 47111 PIN- CLAMP CYLINDER 1

9

10

11 47136-2 SPRING - EXTENSION 1

12 47255 CLEVIS - L.H. 1

13 47253 TIE ROD - CLAMP RETURN 1

14 47254 CLEVIS - R.H. 115 47087 PIN- KNIFE CYLINDER 1

16 S-1073-100 RETAINING RING- 1" 1

17 H-342-2 CYLINDER ASSEMBLY- KNIFE 1

18 47110 PIN- BELLCRANK 2

19 A-10644-8 COLLAR- 1-1/4 1

20 4411 CLEVIS- KNIFE CYLINDER 1

21 4542 STOP- CUT STICK, R.H. 1

22 47005 BELLCRANK ASSEMBLY- CLAMP 1

23 47530 ARCH 1

24

25

26

27

28 SS-798 COLLAR 1

29 8835 PIN- KEEPER 4

30 4504-2 BAR- CLAMP PULL DOWN 1

31 47063 PIN- CLAMP CYLINDER CLEVIS 1

32 47666 NUT- 3/8-24 HIGH HEX 2

33 H-21S-125-0500 PIN- 1/8 DIA. X 1/2 ROLL 1

34 H-6633-612 PIN- #6 X 1-1/2 TAPER 2

35 47662 PIN- #7 TAPER WITH STUD (HARDENED) 2

36 H-6910-404 SCREW- 1/4-20 X 1/2 BUTT. HD. 4

37 H-6913-614 SCREW- 3/8-16 X 1-3/4 HEX 838 H-6913-606 SCREW- 3/8-16 X 3/4 HEX 1

8/11/2019 F.254-I-T

55/139


54

Main Assembly Front View (Rough)47500 Sht. 11 of 16 Rev. G


39 H-6417-8 NUT- 1/2-13 HEX 2

40 H-6918-814 SCREW- 1/2-13 X 1-3/4 SOC. 8

41 H-6918-606 SCREW- 3/8-16 X 3/4 SHC 1

42 H-6951-824 SCREW- 1/2-13 X 1-1/2 FLT. PT. SS. NYLOCK 2

43 H-6423-6 NUT- 3/4-16 HEX 1

44 H-6433-6 NUT- 3/8-16 L.H. HEX 1

45 H-6428-12 NUT- 3/4-16 HEX JAM 1

46 H-6427-16 NUT- 1"-14 HEX 1

47 - - -

48 H-7329-8 WASHER- 1/2 HI COLLAR 6

49 H-7324-8 WASHER- 1/4 INT. TOOTH 4

50 H-6451-0500 RING- EXTERNAL GRIPRING- 1/2 2

51 H-7327-12 WASHER- 3/8 LOCK 9

52 4484 BRACE- TABLE 153 H-6913-616 SCREW- 3/8-16 X 2" HEX HD. 4

47654-1 AIR TABLE

54 47654 TABLE 1

55 H-6913-608 SCREW- 3/8-16 X 1" HEX 6

56 H-7321-6 WASHER- 3/8 SAE FLAT 10

57 H-6918-836 SCREW- 1/2-13 X 4-1/2 SOC. HD. 4

58 H-7329-8 WASHER- 1/2 HI LOCK 4

59 47541 SHELF- HYDRAULIC POWER UNIT 1

8/11/2019 F.254-I-T

56/139


5

Notes

8/11/2019 F.254-I-T

57/139


56

5.10 Main Assembly- Electric Eyes

47500 Sht. 13 of 16 Rev. A (For s/ns 11X1564 and Below)

8/11/2019 F.254-I-T

58/139


5

Main Assembly- Electric Eyes47500 Sht. 13 of 16 Rev. A (for s/ns 11X1564 and Below )

8/11/2019 F.254-I-T

59/139


58

5.11 Main Assembly- Electric Eyes

47500 Sht. 13 of 16 Rev. B (for s/ns 11X1565 and Up)

8/11/2019 F.254-I-T

60/139


5

Main Assembly- Electric Eyes47500 Sht. 13 of 16 Rev. B (for s/ns 11X1565 and Up)


1 EE-3339 CONTROLLER ASSEMBLY - EURO. ELEC. EYES 1

2 E-3336 CONTROLLER - RELAY 1

3 47592 ELECTRIC EYE COVER REF.

4 47590 ELECTRIC EYE GUARD 1

5 16047 HINGE 1

6 E-2810 POWER SUPPLY - 24V OUTPUT 1

7 E-2070-1 END BRACKET - TERMINAL 2

8 E-1977-23 RAIL - TERMINAL, 5" LONG 1

9 E-1172-10 BUSHING 1

10 S-1350-16 STRAIN RELIEF - CABLE 2

11 H-6910-102403 SCREW- #10-24 X 3/8 BUT HD CAP 612 H-6910-102406 SCREW- #10-24 X 3/4 BUT HD CAP 5

13 H-6910-404SS SCREW- 1/4-20 X 1/2 BHC STAINLESS 8

14 H-6910-408 SCREW- 1/4-20 X 1" BUT HD CAP 4

15 H-6423-#10 NUT- #10 HEX KEP 8

16 H-7324-8 WASHER- 1/4 INT TOOTHLOCK 12

17 H-7321-4 WASHER- 1/4 SAE FLAT 4

8/11/2019 F.254-I-T

61/139


60

5.12 Main Assembly Electric Eyes (X, XG, XT)

47500 Sht. 14 of 16 Rev. A (For s/ns 11X1564 and Below)

8/11/2019 F.254-I-T

62/139


6

5.13 Main Assembly - Wiring X Model 1ph

47500 Sht. 16 of 16, Rev. A

8/11/2019 F.254-I-T

63/139


62

5.14 Basic Machine Schematic XG/XT Models

E-2814-1, Rev. C (For s/ns 11X1564 and Below)

8/11/2019 F.254-I-T

64/139


6

Basic Machine Schematic XG/XT ModelsE-2814-2, Rev. A (For s/ns 11X1565 and Up)

8/11/2019 F.254-I-T

65/139


64

5.15 Basic Machine Schematic X Models

E-3171-1 Rev. C (For s/ns 11X1564 and Below)

8/11/2019 F.254-I-T

66/139


6

Basic Machine Schematic X ModelsE-3171-2, Rev. A (For s/ns 11X1565 and Up)

8/11/2019 F.254-I-T

67/139


66

5.16 Power Panel Assembly 305X

EE-3170-1 Sht. 1, Rev. D

8/11/2019 F.254-I-T

68/139


6

Power Panel Assembly 305XEE-3170-1 Sht. 1, Rev. D


1 47512 PANEL - POWER 1

2 E-1089-41 TRANSFORMER - 208-230V "T1" 1

3 E-1143 BRIDGE RECTIFIER - PANEL MOUNT 2

4 E-1429-17 WIRE DUCT & COVER - 9" LONG 1

5 E-1429-18 WIRE DUCT & COVER - 5-1/4" LONG 1

6 E-1977-21 RAIL - TERMINAL - 10" LONG 1


8 EE-3080 WIRES - CUT LIST 1

9 E-2752-2 COVER - TERMINAL BLOCK 3

10 E-2068-3 TERMINAL BLOCK - GROUNDING 1

11 E-2068-8 TERMINAL BLOCK - #10 AWG. 12

12 E-2068-7 TERMINAL BLOCK - 3 AWG. 6

13 E-1974-10 TERMINAL BLOCK - FUSEHOLDER, MIDGET 2

14 E-1974-9 TERMINAL BLOCK - FUSEHOLDER, GLASS 415 E-2069-3 END PLATE 1

16 E-2070-1 END BRACKET 7

17 E-2507-2 FIXED BRIDGE - 2 POLE 1



20 E-1356-147 MARKING STRIP - TERMINAL BLOCK 1






26 E-1453-6 TUBING - SHRINK, 1/8" DIA. 1" LONG 1

27 E-2742-5 TRANSFORMER - 120/230V , 16/24V SC. "T2" 1

28 E-1377 VARISTOR - SUPRESSOR, MOV 1

29 E-2403-2 CONTACTOR - RELAY (CR) 1

30 E-1736-4 QUENCHARC - SNAP-IN MOUNT 1

31 E-1152-56 STAND-OFF - 1/2" LONG 6

32 E-2196-21 HOLE PLUG - 2" DIA 2

33 EE-2807-2 P.C.B. ASM. - MOTOR CONTROLLER 1

34 E-1453-3 SHRINK TUBING - 1" LONG 2

35

36 E-2066-10 PLUG CONNECTOR - P.C.B. 10 PIN (H4 & 5) 2

37 E-2066-8 PLUG CONNECTOR - P.C.B. 8 PIN (H6) 138 E-2066-5 PLUG CONNECTOR - P.C.B. 5 PIN (H7) 1

39 EE-2825-1 CABLE ASSEMBLY - HYD. FAN 1

40 EE-2843-1 CABLE ASSEMBLY - KNIFE LATCH 1

41 EE-2834-1 CABLE ASM. - JUNCTION BOX 1

42 EE-2836-1 CONDUIT ASM. - HYDRAULIC MOTOR, 3 PHASE 1

43 EE-2820 PROX. ASSEMBLY - HYDRAULIC UP "H" 1

44 EE-2820-4 PROX. ASSEMBLY - CLAMP UP "C" 1

8/11/2019 F.254-I-T

69/139


68

Power Panel Assembly 305XEE-3170-1 Sht. 1, Rev. D


45 EE-2820-2 PROX. ASSEMBLY - KNIFE DOWN "K" 1

46 EE-2820-5 PROX. ASSEMBLY - KNIFE UP "U" 1

47 EE-3210 CABLE ASM. - CLAMP COMPRESSOR JUMPER REF

48 EE-2821-8 CABLE ASM. - CUT SOLENOID"A" (MSCE1) 1

49 EE-2842-1 PROX. ASSEMBLY - KNIFE LATCH 1

50

51 EE-2821-6 CABLE ASM. - UNLOAD VALVE SOLENOID "U" 1

52 EE-2821-9 CABLE ASM. - CUT SOLENOID "B" (MSCE2) 1

53 49039 CONDUIT ASSEMBLY - BLOWER/AIR SOL. REF

54 EE-2838-3 CABLE ASSEMBLY - ENCODER 1

55 EE-2817-1 CABLE ASSEMBLY - PRESETTER REF.

56 S-1781-50 LABEL - EURO ELECT. SHOCK 1

57 E-1584-51 LABEL - TRANSFORMER, "T1" 1

58 E-1584-52 LABEL - TRANSFORMER, "T2" 159 E-1584-( ) LABEL - ASM. NO./REV. LEVEL 1

60 S-1781-197 LABEL - GROUND SYMBOL, PRIMARY 1

61 H-6910-83204 SCREW, #8-32NC X 1/2" BUT HD CAP 2


63 H-6423-#6 NUT, #6-32NC HEX 6

64 H-7324-#6 WASHER, #6 INT. TOOTH 14





69 H-6910-403 SCREW, 1/4-20NC X 3/8" BUT HD CAP 5

70 H-7324-8 WASHER, 1/4 INT. TOOTH 5

71 H-7319-4 WASHER, 1/4 USS FLAT 4

72 E-2308 FUSE - 3.2A SB MIDGET, "F4","F5" 2

73 E-889-35 FUSE - 1AMP SLO-BLO GLASS, "F6" 1


75 E-889-5 FUSE - 4AMP SB GLASS, "10","11" 2

76 S-1350-16 STRAIN RELIEF - CABLE 11

77 S-1694 TY-WRAP - CABLE (NOT SHOWN) 10

78 E-2330-7 FUSE - 5A SB, GLASS METRIC (PCF2) 1

79 E-2330-8 FUSE - 6.3A SLO-BLO, GLASS METRIC (PCF3) 1

80 E-2864 SEPARATOR PLATE - TERMINAL BLOCK 2

81 E-1599-11 IC CHIP - 32 PIN PACKAGE (BLANK) 182 E-2805 STARTER - 3 PHASE 1

83 E-2441-11 RELAY - OVERLOAD, 3 PHASE 1

84 E-2376-2 AUXILIARY CONTACT - N.O. 3

85 E-2066-12 PLUG CONNECTOR - P.C.B. 12 PIN (H2) 1

86 E-2232-2 RELAY - CLAMP COMPRESSOR (CC) 1

87 H-7321-#8 WASHER -#8 FLAT 2

8/11/2019 F.254-I-T

70/139


6

Power Panel Assembly 305XEE-3170-1 Sht. 2, Rev. A

8/11/2019 F.254-I-T

71/139


70

5.17 Power Panel Asm. 305X (Blower Opt. Wiring)

EE-3170-1 Sht. 3, Rev. A

8/11/2019 F.254-I-T

72/139


7

Notes

8/11/2019 F.254-I-T

73/139


72

5.18 Power Panel Assembly 305X XG/XT Models

EE-2882-1 Sht 1, Rev. E

8/11/2019 F.254-I-T

74/139


7

Power Panel Assembly 305X XG/XT ModelsEE-2882-1 Sht. 1, Rev. E


1 47512 PANEL - POWER 1

2 E-1089-41 TRANSFORMER - 208-230V "T1" 1

3 EE-3210 CABLE ASM. CLAMP COMPRESSOR JUMPER REF

4 E-1429-17 WIRE DUCT & COVER - 9" LONG 1

5 E-1429-18 WIRE DUCT & COVER - 5-1/4" LONG 1



8 EE-3080 WIRES - CUT LIST 1

9 E-1143 BRIDGE RECTIFIER - PANEL MOUNT 2

10 E-2068-3 TERMINAL BLOCK - GROUNDING 1

11 E-2068-8 TERMINAL BLOCK - #10 AWG. 12

12 E-2068-7 TERMINAL BLOCK - 3 AWG. 6

13 E-1974-10 TERMINAL BLOCK - FUSEHOLDER, MIDGET 2

14 E-1974-9 TERMINAL BLOCK - FUSEHOLDER, GLASS 615 E-2069-3 END PLATE 1

16 E-2070-1 END BRACKET 7










26 E-1453-6 TUBING - SHRINK, 1/8" DIA. 1" LONG 1

27 E-2742-5 TRANSFORMER - 120/230V , 16/24V SC. "T2" 1

28 E-2066-3 PLUG CONNECTOR - 3 PIN (H3 & H19) 2

29 E-2403-2 CONTACTOR - RELAY (CR) 1

30 E-1736-4 QUENCHARC - STARTER MOUNTING 1

31 E-1152-56 STAND-OFF - 1/2" LONG 6

32 E-1152-43 STAND-OFF - 2" LONG 2

33 EE-2807-2 P.C.B. ASM. - MOTOR CONTROLLER 1

34 EE-2820-8 PROX. ASSEMBLY - FALSE CLAMP PLATE "F" 1

35 47157-7 P.C.B. COVER - CLEAR 1

36 E-2066-10 PLUG CONNECTOR - P.C.B. 10 PIN 2

37 E-2066-8 PLUG CONNECTOR - P.C.B. 8 PIN 138 E-2066-5 PLUG CONNECTOR - P.C.B. 5 PIN 1

39 E-2066-4 PLUG CONNECTOR - P.C.B. 4 PIN 1

40 E-2196-21 HOLE PLUG - 2" DIA 2

41 EE-2834-1 CABLE ASM. - JUNCTION BOX 1

42 EE-2833-1 CABLE ASM. - BACKGAGE MOTOR 1

43 EE-2820 PROX. ASSEMBLY - HYDRAULIC UP "H" 1

44 EE-2820-4 PROX. ASSEMBLY - CLAMP UP "C" 1

8/11/2019 F.254-I-T

75/139


74

Power Panel Assembly 305X XG/XT ModelsEE-2882-1 Sht. 1, Rev. E


45 EE-2820-2 PROX. ASSEMBLY - KNIFE DOWN "K" 1

46 EE-2820-5 PROX. ASSEMBLY - KNIFE UP "U" 1

47 E-2232-2 RELAY - AIR BLOWER (AR)/ CLAMP COMPRESS. 2

48 EE-2821-8 CABLE ASM. - CUT SOLENOID"A" (MSCE1) 1

49 EE-2842-1 PROX. ASSEMBLY - KNIFE LATCH 1

50 EE-2821-3 CABLE ASM. - ADJUST. PRESS. SOLENOID "P" 1

51 EE-2821-6 CABLE ASM. - UNLOAD VALVE SOLENOID "U" 1

52 EE-2821-9 CABLE ASM. - CUT SOLENOID "B" (MSCE2) 1

53 49039 CONDUIT ASSEMBLY - BLOWER/AIR SOL. REF

54 EE-3030-1 CABLE ASSEMBLY - ENCODER 1

55 EE-2817-1 CABLE ASSEMBLY - PRESETTER REF.

56 EE-2825-1 CABLE ASSEMBLY - HYD. FAN 1

57 EE-2843-1 CABLE ASSEMBLY - KNIFE LATCH 1

58 E-1377 VARISTOR - SUPRESSOR, MOV 159 E-1453-3 SHRINK TUBING - 1" LONG 2

60 E-2752-2 COVER - TERMINAL BLOCK 3

61 S-1781-197 LABEL - GROUND SYMBOL, PRIMARY 1

62 S-1781-50 LABEL - EURO ELECT. SHOCK 1



65 E-1584-( ) LABEL - ASM. NO./REV. LEVEL 1

66 S-1781-35 LABEL - CAUTION, ELEC. DANGER 1



69 H-6423-#6 NUT, #6-32NC HEX 6






75 H-6910-403 SCREW, 1/4-20NC X 3/8" BUT HD CAP 5

76 H-7324-8 WASHER, 1/4 INT. TOOTH 5

77 H-7319-4 WASHER, 1/4 USS FLAT 4

78 E-2308 FUSE - 3.2A SB MIDGET, "F4","F5" 2



81 E-889-5 FUSE - 4AMP SB GLASS, "F8","F9","10","11" 4

8/11/2019 F.254-I-T

76/139

8/11/2019 F.254-I-T

77/139


76

Power Panel Assembly 305X XG/XT ModelsEE-2882-1 Sht 2, Rev. A

8/11/2019 F.254-I-T

78/139


7

Notes

8/11/2019 F.254-I-T

79/139


78

5.19 Interconnection Diagram 305X XG/XT Models

E-2840-1, Rev. E (For s/ns 11X1564 and Below)

8/11/2019 F.254-I-T

80/139


7

Interconnection Diagram 305X XG/XT ModelsE-2840-3, Rev. A (For s/ns 11X1565 and Up)

8/11/2019 F.254-I-T

81/139


80

5.20 Interconnection Diagram 305X

E-2841-1 Rev. D (For s/ns 11X1564 and Below)

8/11/2019 F.254-I-T

82/139


8

Interconnection Diagram 305XE-2841-3 Rev. A (For s/ns 11X1565 and Up)

8/11/2019 F.254-I-T

83/139


82

5.21 Control Console Assembly - 305XG Model

EE-2823, Rev. C (For Non-Back lit displays)

8/11/2019 F.254-I-T

84/139


8

Control Console Assembly - 305XG ModelEE-2823-1, Rev. A (For Back lit displays)

8/11/2019 F.254-I-T

85/139


84

5.22 Control Console Assembly - 305X

EE-2850, Rev. C (Non-Back Lit Display)

8/11/2019 F.254-I-T

86/139


8

Control Console Assembly - 305XEE-2850-1, Rev. A (Back Lit Display)

8/11/2019 F.254-I-T

87/139


86

5.23 Control Console Assembly - XT Model - Color LCD

EE-2998-3 rev B (For Serial Numbers 09X1505 and below)

8/11/2019 F.254-I-T

88/139


8

Control Console Assembly - XT Model - Color LCDEE-2998-4 rev A (For Serial Numbers 09X1506 and Up)

8/11/2019 F.254-I-T

89/139


88

5.24 Cut Button Assembly (Obsolete)

EE-2832-1, Rev. B (Note: these cut switches are no longer available they havebeen replaced with K-3374)

8/11/2019 F.254-I-T

90/139


8

Kit - Cut But ton ReplacementK-3374, Rev. B

8/11/2019 F.254-I-T

91/139


90

5.25 Cut Button Assembly (Current)

EE-3382, Rev. B

8/11/2019 F.254-I-T

92/139


9

Cut Button Assembly Parts ListEE-3382, Rev. B


1 47665 CONTROL BOX ASSEMBLY - 305X 1

2 E-3127-4 PUSHBUTTON SWITCH - MUSHROOM, 3 N.O. 2

3 E-2078-3 CABLE - #18GA. 8 COND. 49" LONG 1

4 E-2078 CABLE - #18GA. 6 COND. 38" LONG 1

5 E-3082 SWITCH - MAIN DISCONNECT (BODY) 1

6 E-3083 SWITCH FACE - MAIN DISCONNECT 1

7

8 E-2190-2 3/4" CONDUIT CONNECTOR - 90%%d 2

9 E-2189-2 CONDUIT - PLASTIC, 16" LONG 1

10 E-1213-B WIRE - #10 GA. BLACK MTW 38" LONG 6

11 E-2743-1 WIRE - #14 GA. GRN/YEL TEW 38" LONG 1

12 E-1214-64 CONNECTOR - 1/4" RING (16-14GA) 1

13 H-6423-4 NUT - 1/4-20 HEX 114 S-1781-42 LABEL - GROUND SYMBOL, SECONDARY 1

15 S-1781-11 LABEL - ELECTRIC SHOCK 1

16 E-1237-6 WIRE NUT - BLUE 3

8/11/2019 F.254-I-T

93/139


92

5.26 Kit Ergonomic Touch Switch (Cut Button Option)

K-3404, Rev. A

8/11/2019 F.254-I-T

94/139


9

Kit Ergonomic Touch Switch (Cut Button Option)K-3404, Rev. A (For S/Ns 11X1565 and up)

8/11/2019 F.254-I-T

95/139


94

5.27 Line Light Assembly

47538, Rev. D

8/11/2019 F.254-I-T

96/139


9

5.28 Air Table Blower Assembly Single Phase

47578, Rev. C

8/11/2019 F.254-I-T

97/139

8/11/2019 F.254-I-T

98/139


9

Notes

8/11/2019 F.254-I-T

99/139


98

5.30 Backgauge Control Assembly

49249 Rev. B

8/11/2019 F.254-I-T

100/139


9

Backgauge Control Assembly, 49249 Rev. B

NO. PART NO. DESCRIPTION QTY

1 41074 POLYURETHANE DOT 2

2 47053 COUPLING 1

3 49248 PILLOW BLOCK BRACKET 1

4 63210-1 FRONT PILLOW BLOCK 1

5 63213 TORSION SPRING 1

6 63214 ACTUATOR 1

7 63218 KNOB 1

8 63221 CONTROL KNOB SHAFT 1

9 EE-3213 POTENTIOMETER 1

10 H-6424-6 NUT - 3/8-16 HEX JAM 2

11 H-6910-610 SCREW - 3/8-16 X 1-1/4 BUTTON HEAD CAP 2

12 H-6940-102404 SCREW - #10-24 X 1/4 FLAT SOC SET 1

13 H-6940-406 SCREW - 1/4-20 X 3/8 FLAT SOC SET 1

14 H-7321-6 WASHER - 3/8 SAE PLAIN 2

15 H-7322-8 WASHER - 1/2 POLISHED 2

16 H-7327-12 WASHER - 3/8 MEDIUM LOCK 2

17 H-21S-250-1500 ROLL PIN - 1/4 X 1-1/2 1

18 S-1193-37 E-RING - 3/8" 1

19 SU-30-107 GREASE DAMPENING, 1200 VISCOSITY 1

8/11/2019 F.254-I-T

101/139


100

5.31 X/XG/XT Troubleshooting

EE-2807-2 (Order programmed IC chip separately.)The following is a description of the various diagnostic LEDs in the power panel. These lights areindicators used to show input and output status.

8/11/2019 F.254-I-T

102/139


10

5.32 Description of Error Messages

Message Description Test

Backgauge Failure Backgauge doesnt move Mec

f.254-i-t

Documents