fa-10dccru (1), quick setup guide (1), cd-rom (1

FA10DCCRU_SETUPGUIDE-E-4.DOCX

FA-10DCCRU Quick Setup Guide

Packing list: FA-10DCCRU (1), Quick Setup Guide (1), CD-ROM (1) (including Operation Manuals), AC cord (1), AC cord retaining clip (1 set), Rack mount bracket set (1 set), * The FA-10DCCRU is inoperable, except for the ability to change its own settings, unless it is connected to a Main Unit.

1. Rear Connectors 4. Connecting Main Units

There are two ways to connect to an FA Unit (FA-505, FA-1010, FA-9520, FA-

9500 or FA-9600): Direct mode (default) and Unit ID Selection mode.

Direct mode: Connects a unit by specifying a DIRECT number among 20.

(Unit ID number 1 to 20 are assigned to Direct number 1 to 20 as factory

default.)

Unit ID Selection mode: Connects a unit by specifying an ID from among

100 ID numbers.

* Note that startup connection may require one and a half second at most.

◆ Connecting in Direct Mode (default)

In the following example, an FA-10DCCRU connects to an FA Unit whose

DIRECT number is 3.

(1) Press the 1-5 button tree times.

When the connection process starts, “Connection (Direct)” is displayed.

(2) When the “Please Choose Direct MU No” message appears and Buttons

(1-5, 6-10, 11-15 and 16-20) are flashing, press 1-5 again to confirm the

connection target.

(3) When “Connected: FA-1010” is displayed, the connection is established.

◆ Changing Connection Mode from Direct to Unit ID Selection

(1) Press and hold down FS SEL for about 3 seconds.

(2) Press + to select Unit Mode Connection.

(3) Press SELECT or FS SEL to confirm the change.

◆ Connecting in Unit ID Selection Mode

In the following example, an FA-10DCCRU connects to an Unit whose UNIT ID

number is 10.

(1) Press 11-15/UNIT.

(2) Turn VIDEO LEVEL to select “ID10“ (MU UNIT ID number), then “ID10:

XXXXX” will be displayed, scrolling from left to right.

If “Unit Name” (for example, FA-1010) and “IP address” are saved to ID10,

the message as shown below appears.

ID10: FA-1010

If only “IP Address” is saved to ID10, the message as shown below

appears.

ID10: 192.168.0.10 (No Name)

(3) Press SELECT to confirm the connection target.

(4) When “Connected: FA-1010” appears, the connection is established.

1-5 6-10

11-15/UNIT 16-20

BYPS/OP FS SEL

MEMORY/SET

0 1 2 3 4 5 6 7

FREEZE

CLIP

SPLIT

SELECT - +

SAVE LOAD CLEAR

PROCESS CONTROL

VIDEO LEVEL Y LEVEL C LEVEL SETUP/BLUCK HUE

UNITY UNITY UNITY UNITY UNITY

SYSTEM

GRP ADJ

UNITY UNITY UNITY UNITY UNITY UNITY

R G B R G B

WHITE LEVEL BLACK LEVEL

UNITY UNITY UNITY

R G B

GAMMA WHITE BAL FA-10DCCRU

CENTER DIF

BLACK SEPIA

2. Installing the AC Cord Retaining Clip

Securely connect the AC cord with the supplied ladder strap/retaining clip assembly to prevent accidental removal from the FA-1010. Be sure to install the AC cord retaining clip before mounting the unit into a rack.

1) Wrap the retaining clip around the AC cord. (with the anchor of the ladder strap toward the unit.)

2) Insert the anchor into the hole above the AC IN socket.

3) Lightly fasten the clip around the AC cord.

4) Plug in the power cord.

5) Slide the clip on the ladder strap toward the plug.

6) Fasten the clip tightly.

7) Gently pull on the AC cord to ensure it securely fastened.

3. Connection

* Complete connections before turning the power of the unit on.

Open a web browser on the connected computer, and enter the address

http://192.168.0.101/ (factory default setting) in the address bar. The authentication

dialog box (the first time only) and Information page as shown below appear.

Precautions

⚫ Operate the unit only at the specified supply voltage. ⚫ Ensure the unit is properly grounded at all times. ⚫ Ensure the power cord and connectors are firmly connected. ⚫ Do not access circuitry with power applied to the unit. ⚫ Unit should not be operated or stored with the cover, panels, and/or casing

removed. ⚫ Unit should not be operated or stored in a humid, dusty, etc. environment.

Doing so could result in fire or electrical shock. ⚫ Do not allow fluids, metal fragments, or any other foreign objects to enter

the unit. If foreign matter does enter the unit, turn the power off and disconnect the power cord immediately. Remove the material or contact your authorized service representative

⚫ If you notice any strange smells or noises coming from the unit, turn the power off immediately, turn OFF the power switch, disconnect the power cord, then contact your authorized service representative.

2)

4) 3)

5) 6)

AC cord retaining clip anchor hole

Ground Terminal

GPI connectors for FA-AUX30 option connection

A LAN connector for FA-1010 control AC IN FAN

AC100-240V 50/60Hz IN

GPI3GPI2GPI1TO MU

(10/100/1000BASE-T)POWER

ON

OFF

PS1/LOCK

PS2/LOCK

EVENT

VIDEO IN

GENLOCL

REMOTE

AUDIO IN

FAN ALARM

DC POWERF 1

F 2

F 3

F 4

F A - 9 5 2 0H D / S D F R A M E S Y N C H R ON I ZE R

DISPLAYF 1

UN ITY

F 2

UN ITY UN ITY

F 3 F 4

UN ITY

PROCESS

SDI AUDIO

MAPPING

VIDEO OP

AUDIO OP

C C

A V O CLIP

DELAY

VIDEO SYS

AUDIO SYS

AES AUDIO

CONV1

ANALOG

IN SEL

DOWNMIX

STATUS

OTHER

CONV2

MASTER

OUT SEL

M OD E

VIDEO

AUDIO

FA-1010FRAME SYNCHRONIZER

INITIALIZATION

OPTION SLOT

A B C D

INSTALL

VIDEO IN

AUDIO IN

BY-PASS

VIDEO

AUDIO

1 2 3 4 5 6 7 8 9 10

DC POWER 1 GENLOCK

DC POWER 2

FAN ALARM LTC IN

SDI IN

PC

Hub FA-10GUI (PC)

FA-10DCCRU FA-1010


INITIALIZATION

OPTION SLOT

A B C D

INSTALL

VIDEO IN

AUDIO IN

BY-PASS

VIDEO

AUDIO

1 2 3 4 5 6 7 8 9 10

DC POWER 1 GENLOCK

DC POWER 2

FAN ALARM LTC IN

SDI IN


INITIALIZATION

OPTION SLOT

A B C D

INSTALL

VIDEO IN

AUDIO IN

BY-PASS

VIDEO

AUDIO

1 2 3 4 5 6 7 8 9 10

DC POWER 1 GENLOCK

DC POWER 2

FAN ALARM LTC IN

SDI IN

FA-10RU

FA-95RU

FA-9520

FA-9500 MASTER

CONV2

OUT SEL

MODE

VIDEO

AUDIO

ANALOG

CONV1

IN SEL

DOWNMIX

STATUS

OTHER

C C

AES AUDIO

CLIP

DELAY

AUDIO SYS

VIDEO SYS

AUDIO OP

VIDEO OP

MAPPING

A V O

PROCESS

SDI AUDIO

F4

UNITYUNITYUNITYUNITY

F3F2F1

F A - 9 5 0 0

DISPLAY AREA

H D / S D F R A M E S Y S N C H R O N I Z E R

VIDEO IN

AUDIO IN

GENLOCK

REMOTE

FAN ALARM

DC POWER

BY-PASS

LOCK

EVENT

ON

OFF

POWER

F1

F2

F3

F4

MASTER

CONV2

OUT SEL

MODE

VIDEO

AUDIO

ANALOG

CONV1

IN SEL

DOWNMIX

STATUS

OTHER

C C

AES AUDIO

CLIP

DELAY

AUDIO SYS

VIDEO SYS

AUDIO OP

VIDEO OP

MAPPING

A V O

PROCESS

SDI AUDIO

F4


F3F2F1

F A - 9 5 0 0

DISPLAY AREA


VIDEO IN

AUDIO IN

GENLOCK

REMOTE

FAN ALARM

DC POWER

BY-PASS

LOCK

EVENT

ON

OFF

POWER

F1

F2

F3

F4

MASTER

CONV2

OUT SEL

MODE

VIDEO

AUDIO

ANALOG

CONV1

IN SEL

DOWNMIX

STATUS

OTHER

C C

AES AUDIO

CLIP

DELAY

AUDIO SYS

VIDEO SYS

AUDIO OP

VIDEO OP

MAPPING

A V O

PROCESS

SDI AUDIO

F4


F3F2F1

F A - 9 5 0 0

DISPLAY AREA


VIDEO IN

AUDIO IN

GENLOCK

REMOTE

FAN ALARM

DC POWER

BY-PASS

LOCK

EVENT

ON

OFF

POWER

F1

F2

F3

F4

DISPLAY AREA

POWER

ON

OFF

LOCK

MUSELECT

EVENT

BY-PASSVIDEO IN

AUDIO IN FAN ALARM

GENLOCK

REMOTE

F 1

F 2

F 3

F 4

R E M O T E C O N T R O L U N I TF A - 9 5 R U

F1 F2 F3 F4

UNITYUNITY UNITY UNITY

PROCESS

SDI AUDIO

C C

AES AUDIO

CONV1

ANALOG

CONV2

MASTER

AVO

MAPPING

CLIP

DELAY DOWNMIX

IN SEL OUT SEL

MODE

AUDIO OP

VIDEO OP VIDEO SYS

AUDIO SYS

STATUS

OTHER

VIDEO

AUDIO

POWER

ON

OFF

MU SELLOCK

FS SELFS LINK

EVENT

GENLOCK

FREEZE

TEST SIGNAL

BY-PASS

FAN ALARM

DC POWER

REMOTE CONTROL UNIT FA-10RU

DISPLAY AREAF1 F2 F3 F4

UNITY UNITY UNITY UNITY

1 2 3 4

5 6 7

9 10 0

OPTION8

PROCEMB

CCSETUP

CLIPDWN MIX

BY-PASSMAPPING

INPUTAES

CLN SWGAINI

OUTPUTDELAY

ANC

ANALOGSYSTEM STATUS

VIDEO

AUDIO

1-5 6-10

11-15/UNIT 16-20

BYPS/OP FS SEL

MEMORY/SET

0 1 2 3 4 5 6 7

FREEZE

CLIP

SPLIT

SELECT - +

SAVE LOAD CLEAR

VIDEO LEVEL Y LEVEL C LEVEL HUE


SYSTEM

GRP ADJ


R G B R G B


UNITY UNITY UNITY

R G B


CENTER DIF

BLACK SEPIA

SETUP/BLACK

PROCESS CONTROL

1-5 6-10

11-15/UNIT 16-20

BYPS/OP FS SEL

MEMORY/SET

0 1 2 3 4 5 6 7

FREEZE

CLIP

SPLIT

SELECT - +

SAVE LOAD CLEAR



SYSTEM

GRP ADJ


R G B R G B


UNITY UNITY UNITY

R G B


CENTER DIF

BLACK SEPIA

SETUP/BLACK

PROCESS CONTROL

1-5 6-10

11-15/UNIT 16-20

BYPS/OP FS SEL

MEMORY/SET

0 1 2 3 4 5 6 7

FREEZE

CLIP

SPLIT

SELECT - +

SAVE LOAD CLEAR



SYSTEM

GRP ADJ


R G B R G B


UNITY UNITY UNITY

R G B


CENTER DIF

BLACK SEPIA

SETUP/BLACK

PROCESS CONTROL

◆ Assigning Main Units

Click Unit ID Assignment to open the dialog box. The dialog example below is for assigning main units to Unit ID 1 to 20.

Enter a unit IP address and port number. Enter a unit name to be displayed for settings, if necessary, under Unit Name. After assigning IP addresses, click Apply. (The assignments are effective without rebooting.) Unit names can be set with up to 15 alphanumeric characters.

Click Network Settings in the dialog window. Enter your user name and password. User name: fa10dccru Password: foranetwork Then, click OK. After completing the settings, click Submit, and then click Restart. The Restart window appears. Click Restart in the window. The settings take effect after the restart is completed.

https://www.for-a.com/

You can download manuals and other documents by registering your email address.

http://192.168.0.10/

FA10DCCRU_SETUPGUIDE-E-4.DOCX

FA-AUX30 GPI devices are specifically designed to send or receive FA-10DCCRU GPI signals.

Thirty buttons on the front panel allow to send / receive GPI signals to / from 30 GPI ports on the FA-10DCCRU.

◆ Connection

GPI input /output functions can be assigned to GPI ports on the FA-10DCCRU using the supplied FA GPIO Editor software.

◆ Installing and Starting the FA GPIO Editor

(1) Before installing the software, close all other applications on the computer.

(2) Insert the supplied CD-ROM into the PC.

Click “FA GPIO Editor > setup “ on the CD-ROM to start the installation.

(3) Follow the installation wizard to install the FA GPIO Editor.

(4) After the installation, click the FA GPIO Editor shortcut icon on the desktop

to start the FA GPIO Editor.

(5) Enter the FA-10DCCRU IP address, user name and password.

Click Load to load the current settings.(All ports are set to None as factory default.)

IP address: 192.168.0.101

User name: fa10dccru

Password: foranetwork

5. FA-AUX30 Option

FA-AUX30 rear panel

GPI1 GPI2 GPI3

FA-10DCCRU

TO MU

(10/100/1000BASE-T)

GPI1 GPI2 GPI3

POWER

AC

100-2

40V

50/6

0H

z IN

OFF

ON

Supplied FA-AUX30 cable x 3

FA-AUX30 front panel

◆ Assigning GPI Functions

(1) The FA GPI Editor screen has three tab windows, for which 10 ports per window can be set. These tab windows correspond to three button blocks

on the FA-AUX30 front panel. Click a tab to display the desired port setting window.

(2) Refer to the “Input Setting List” table below to set Setting 1, Setting 2 and Setting 3 for each port, as needed. The Setting 2 and Setting 3 settings

depend on the Setting 1 selection.

<Setting Examples>

-If set to MU Select Unit ID1 FS1: Select FS1 in main unit with Unit 1D 1.

-If set to FS Select FS1 : Select FS1 in the connected main unit.

-If set to Freeze(On/Off) None : Set Freeze On/Off for the selected FS.

-If set to Freeze(On/Off) FS1 : Set Freeze On/Off for FS1.

* See the “Detailed Input Settings” table below for detailed input settings

(3) After all settings are finished, click Apply.

* Refer to “FA-10DCCRU Operation Manual” for GPI output settings.

GPI Port 1-10 GPI Port 11-20 GPI Port 21-30

Port 1 Port 11 Port 21

DC POWER

FA-AUX30AUXILIARY UNIT

Port 6 Port 16 Port 26

Input Setting List

Port No. Setting 1 Setting 2 Setting 3

1-30

None - -

MU Select Disconnect -

Unit ID1-100 None, FS1-10

FS Select FS1-10 -

FS Link(On/Off) All Clear, FS1-10 -

Freeze(On/Off) None, FS1-10 -

Split Mode Off, Mode1-3 None, FS1-10

CC Mode Balance, Differential, Sepia None, FS1-10

Gamma Curve Center, Black, White None, FS1-10

Clip Off, YPbPr, RGB None, FS1-10

GPI Lock(On/Off) - -

Group Adjust(On/Off) - -

Event Load Default, Event1-100 -

Event Save Event1-100 -

Detailed Input Settings

Setting 1 setting Description

None No function

MU Select MU Select allows you to select a main unit under Setting 2 (Unit ID1 - 100) and an FS of the main unit under Setting 3 (FS1 - 10).

If set to None under Setting 3, the last controlled FS is selected. Main unit IP addresses must be set for Unit ID numbers in advance.

If set to Disconnect under Setting 2, the port can disconnect main units.

FS Select FS Select allows you to select an FS under Setting 2, FS1 - FS10 if connecting to FS-1010, FS1-FS5 if connecting to FS-505. If connecting to FA

-9520 (FA-9520 mode) or FA-9600, FS1 and FS2 of Color Correctors are selectable. FS Select is inoperable when connecting with FA-9520 (FA-

9500 mode) or FA-9500 units.

FS Link(On/Off) Allows you to set an FS linked or unlinked under Setting 2. If All Clear is set under Setting 2, all FS channels are linked off.

* This function is disabled for FA-9600.

Freeze(On/Off) Allows you to set Freeze to On or Off.

If an FS is selected under Setting 2, the controlled FS is changed to the selected one and a Freeze setting is applied to it.

If None is set under Setting 2, a Freeze setting is applied to the current FS.

Split Mode Allows you to set Split mode under Setting 2.

If an FS is selected under Setting 3, the controlled FS is changed to the selected one and a Split Mode setting is applied to it.

If None is set under Setting 3, a Split Mode setting is applied to the current FS.

CC Mode Allows you to set Color Correction mode under Setting 2.

If an FS is selected under Setting 3, the controlled FS is changed to the selected one and a CC Mode setting is applied to it.

If None is set under Setting 3, a CC Mode setting is applied to the current FS.

Gamma Curve Allows you to set Gamma Curve under Setting 2.

If an FS is selected under Setting 3, the controlled FS is changed to the selected one and a Gamma Curve setting is applied to it.

If None is set under Setting 3, a Gamma Curve setting is applied to the current FS.

Clip Allows you to set Clip mode under Setting 2. Refer to ”FA-10DCCRU Operation Manual” for details.

GPI Lock(On/Off) Allows you to enable (GPI Lock Off) / disable (GPI Lock On) all GPI inputs.

Group Adjust(On/Off) Allows you to enable / disable group adjustment. The group adjustment functions in the same manner as that in FA-10DCCRU.

Event Load Allows you to load an event set under Setting 2 (Event1 - 100).

Event Save Allows you to save settings to an event set under Setting 2 (Event1 - 100).

* GPI functions can be assigned to ports individually or in groups using Pattern Load. Refer to “FA-10DCCRU Operation Manual” for more details.

fa-10dccru (1), quick setup guide (1), cd-rom (1

Documents