feathermate assembly specifications contact us today … ˜˚˛˝˙˚ˆˇ˛˝˚˘ ˛ ˚˘ ˚ ˘ ˘...
TRANSCRIPT
Features• Delay match per assembly: ±2 ps • Zero force to disengage• .085” [2.16mm] pitch
O: 561.840.1800
Applications
Benefits• Keying eliminates mismating• No custom tooling required• Solder free installation• Reflow oven (265°C) safe• Zero disengagement eliminates damage to PCB solder joints
• Bench-top testing• Evaluation boards• Automated Test Equipment (ATE)• High density multiports• CPW/Microstrip or Stripline Launch
FeatherMate Assembly SpecificationsElectrical Condition Specification
Frequency Range N/A DC - 40 GHz
Impedance N/A 50Ω
VSWR DC to 18 GHzDC to 40 GHz
1.20:1 *See Figure 11.30:1 (page 2)
Delay Match Per assembly ±2 ps
Mechanical SpecificationCenter to Center Spacing .085" [2.16mm] pitch
Engage Force 2 oz/port
Disengage Force Zero
Mating Cycles (min) 1000
Temperature Range (Cable Assembly) -65 to +165°C
Temperature Range (PCB Mount Bracket) -65 to +265°C(Suitable for Reflow Oven)
Contact us today for information regarding our 40 GHz FeatherMate
Evaluation Kit
PCB
FeatherMate Cable Assembly
Block4x Ø.047
FleXtra® (6.0”)4x
2.92mmMale
GateFlag
GateFlag
.125”.125”
Figure 1
VSWR Gating
VSWR was plotted by averaging the data of 10 mates. Data collected was gated from .125” into the cable and .125” into the board trace as illustrated. See Figure 1.
Cable Specifications (FleXtra® Ø.047)
Electrical SpecificationImpedance 50Ω
Velocity of Propagation 70% Nominal
Capacitance 29.0 pF/ft
Cutoff Frequency 108.0 GHz
Mechanical SpecificationOperating Temp Range -65 to +165°C
Inside Bend Radius R. 100 min.
Weight 3.5 lbs/1000 ft
Jacket OD Ø.059 max.
Insertion Loss (Ø.047 Cable Only)
0
50
100
150
200
250
300
350
400
0 5 10 15 20 25 30 35 40
Inse
rtio
n Lo
ss (
dB/1
00
ft)
Frequency (GHz)
Inse
rtio
n Lo
ss (
dB/1
00
ft)
Frequency (GHz)
Average VSWR Over Multiple Mates
1
1.05
1.1
1.15
1.2
1.25
1.3
1.35
1.4
1.45
1.5
0 5 10 15 20 25 30 35 40Frequency (GHz)Frequency (GHz)
FeatherMate 4 Port FeatherMate 8 Port
PCB
FeatherMate Cable Assembly
Block (2x)
4x Ø.047
FleXtra® 6.0” (2x)4x
2.92mmMale (2x)
Figure 2
Insertion loss was tested as a thru measurement on two FeatherMate connectors to four 2.92mm Ø.047 6” FleXtra® cable assemblies joined via a test PCB. FeatherMate connectors were mated and demated 10 times by hand to generate the results shown. See Figure 2.
FeatherMate Assembly ProcessStep 1:
• Select and mount the appropriate hardware set for the intended board (see page 4)
Step 2:
• After placing the bushings on the bottom side of the board, from the top torque the provided single .063” hex socket screw in each bushing (solder-free operation)
Note: the internal diameter of one of the bushings is larger than the other to prohibit mismating and to provide the keying feature of the FeatherMate
Step 3:
• Tighten the FeatherMate cable assembly block .050” hex socket screws into both bushingsThe compression of the center contact spring pin and the flexure of the cantilever beam grounding element store the potential energy in the contact system to maintain consistent normal force for the signal path
Insertion Loss Repeatability Over Multiple Mates
-4.5
-4
-3.5
-3
-2.5
-2
-1.5
-1
-0.5
00 5 10 15 20
Inse
rtio
n Lo
ss (
dB)
Frequency (GHz)
Inse
rtio
n Lo
ss (
dB)
Frequency (GHz)
Unmated FeatherMate Set Mated FeatherMate Set
Board ThicknessBoard Group Hardware Set
Min Max.033” .062” 1 FMHS1
.055” .084” 2 FMHS2
.076” .105” 3 FMHS3
.094” .123” 4 FMHS4
.110” .160” 5 FMHS5
.144” .192” 6 FMHS6
.173” .223” 7 FMHS7
.200” .250” 8 FMHS8
.225” .275” 9 FMHS9 Hardware Set
Rev. 3 (01/16)
O: 561.840.1800
Mechanical Hardware
Note: Ø.080±.002 hole can be oriented and placed anywhere along the stitched arc as shown, both sides.
.530
.655
GASKET
CONTACT
BLOCK
.870
.995
BACKSHELL
2X .050 HEX.SOCKET HEAD SCREWS
.530±.002
.138±.001
2XØ.156±.001
3X .085±.001
.145±.002SEE NOTE
2XØ.080±.001
SMALLBUSHING
LARGEBUSHING
.870±.002
.138±.001
2XØ.156±.001
7X.085±.001
.145±.002
2XØ.080±.001
LARGEBUSHING
SMALLBUSHING
SEE NOTE
.530±.002
.138±.001
2XØ.156±.001
3X .085±.001
.145±.002SEE NOTE
2XØ.080±.001
SMALLBUSHING
LARGEBUSHING
.870±.002
.138±.001
2XØ.156±.001
7X.085±.001
.145±.002
2XØ.080±.001
LARGEBUSHING
SMALLBUSHING
SEE NOTE
• Mounting hardware is custom configured to match PCB thickness
• FeatherMate assemblies include one set of hardware
• Additional hardware sets can be ordered by “Hardware Set” part number
• Mounting hardware is economical and reuseable
Mounting Hardware Ordering Specifications
FeatherMate Connector Block and Hardware Set
PCB Board Trace
4 Port 8 Port