feniex 4200 controller instruction manual v2
TRANSCRIPT
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
1/10
www.Feniex.com
E-mail: [email protected]
Support line: 1.800.615.8350
nstallation and Operational Guide
FENIEX 4200
This instruction manual serves as a guide for the 4200 smart controller. IMPORTANT! Please readthrough all provided instructions and any listed warnings in regards to product use.
ecord Product Serial Number:
MODEL #: C-4200
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
2/10
SAFETY REGULATIONS
Warranty
The following provides all the information necessary to safely operate the previously listed products of Fen
ndustries, Inc. Please read this manual thoroughly before installing or operating your new product in order to
prevent any damage or injury. Failure to follow the listed instructions in the manual may result in damage to your
product or personal injury.
Proper installation of this product requires good knowledge of automotive systems, electronics and
procedures.
Please guarantee all vital components of the vehicle are not in danger of being damaged by drilling holes
necessary for installation. Check all sides of the mounting surface before drilling any holes into the vehicle
Do not install this product in any way that interferes with the deployment of the air bag. Doing so may
damage the effectiveness of the air bag and can lead to serious personal and vehicle injury. The installer
will assume full responsibility of proper installation of the new unit.
Please clean the mounting surface before installation of the unit when using tape, brackets, magnet,
Velcro or suction cups.
The product ground wire must be connected directly to the Negative (-) battery post for effective use of
the unit. Please follow all wiring guidelines provided to guarantee long lifespan and productivity. Failing to
follow these instructions may result in damage to the product.
Feniex Industries, Inc. warrants to the original purchaser that the product shall be free from defects in material an
workmanship for thirty-six (36) months from the date of purchase for all LED products. Feniex Industries warranties comp
systems, horns, speakers and sirens and controllers for 24 months, while coverage for strobes, switches and flashers are
a 12 month term. If an extended warranty is added during time of purchase, the warranty coverage term will be 60 month
or led products, 36 months for computer/hardware systems, horns, speakers and sirens and controllers, and 24 month
strobes, switches and flashers. If a defect occurs within this time period, Feniex will repair or replace malfunctioning parts
of charge.
If a warranty problem occurs, please contact customer support at 1.800.615.8350 or visit the web site at www.Feniex.com. If the product needs to be returned for repair or replacement, call our customer support line to receive a re-urn merchandise authorization number. Operational times will be from 10 a.m. to 5 p.m. central time. Please do not send
product without contacting Feniex first for a RMA number and filling out the return form located at www.feniex.com under About Us tab.
SERVICE AFTER EXPIRATION
Feniex Industries will still provide service for all products after expiration of the warranty. For any issues, call thecustomer support line. In some instances it may be necessary for the product to be shipped, freight prepaid and insured fooss or damage to Feniex headquarters.
WARNING: Utilizing non-factory screws and mounting brackets may result in loss of warranty covera
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
3/10
This warranty shall not apply if this product is a.) used with products not sold or licensed by Feniex Industr
nc. (including, but not limited to, power supplies, radios, control devices, adapters and power converters); b.) is us
or rental; c.) is modified or tampered with; d.) is damaged by negligence, accident, unreasonable use, or by other
auses unrelated to defective materials or workmanship; or e.) has had the serial number altered, defaced or
removed.
Any applicable implied warranty, including warranties of merchantability and fitness for a particular purpos
re hereby limited in duration to the warranty periods described previously in this manual. In no event shall Feniexndustries be liable for consequential or incidental damages resulting from the breach of any implied or express
warranties. This warranty is valid world wide.
COPYRIGHT
Feniex and the third party supplied products described in the instruction manual may include copyrighted
materials. Laws in the United States and other countries preserve for Feniex certain exclusive rights for copyrigh
roducts, including the exclusive right to copy or reproduce in any form the copyrighted product.
This instruction manual and the Feniex products described in this instruction manual may include or
escribe copyrighted Feniex material. Laws in the United States and other countries preserve for Feniex Industrie
nd its licensors certain exclusive rights for copyrighted material, including the exclusive right to copy, reproduceny form, distribute and make derivative works of the copyrighted material. Accordingly, any copyrighted material
eniex and its licensors contained herein or in the Feniex products described in this instruction manual may not
opied, reproduced, distributed, merged or modified in any manner without the express written permission of Fen
ndustries, Inc.
The product described in this document is the property of Feniex Industries, Inc. It is furnished by express
cense agreement only and may be used only in accordance with the terms of such an agreement. Products and
documentation are copyrighted materials. Making unauthorized copies is prohibited by law. No part of the producor documentation may be reproduced, transmitted, transcribed, stored in retrieval system or translated into any
anguage or computer language, in any form or by any means, without prior permission of Feniex Industries, Inc.
Feniex and the stylized Feniex logo are registered in the U.S. Patent & Trademark Office. All other product
ervice named in this guide are the property of Feniex Industries, Inc.
WARRANTY LIMITATIONS
FENIEX PRODUCT COPYRIGHTS
USAGE AND DISCLOSURE RESTRICTIONS
REGISTERED TRADEMARKS OF FENIEX INDUSTRIES, INC
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
4/10
Input Voltage 11Vdc to 16 Vdc
Temperature Range -40C to +70C
Standby Current Less than 0.05 amps
Humidity 99%
Logic Input A-B Ground
Logic Input C-D-E Positive
Logic Input F Night Mode (+)
Logic Input G Day Mode (+)
Logic Input H Ignition (+)
Output 1 3 Amps (-)
Outputs 2-3 WigWag 10 Amps (+)
Outputs 4-20 10 Amps (+)
Outputs 21-24 25 Amps Group (+)
Outputs 25-28 25 Amps Group (+)
Outputs 29-32 30 Amps Group Continuous (+)
Max input current 60 Amps
Dimensions Controller 6.8 x 3.5 x 1.3
Dimensions Power Supply 6 x 4 x 1.5
Bluetooth Range 40 Feet (+/- 5 Feet)
ystem SpecifcationBelow you will nd the key specications of the 4200 system. Review the information to better determine your installation needs.
Warning, do not deviate from the specied voltage.
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
5/10
Control Head Mounting
llow the instructions when mounting the 4200 control head. Do not use any hardware other than the factory provided s
en securing the U-bracket to the control head.
Mounting
p 1- Select a dry, cool location to mount the control head.
p 2- Remove the U-bracket from the controller by unscrewing the two factory provided screws located on either side o
bracket.
p 3 Decide which mounting option you would like to use. Option A is mounting vertically, allowing the controller to h
ption B is surface mount, mounting from the rear.
p 4 - Mount the U-bracket in the desired location using two self-tapping screws. If you wish to use machine screws, sim
ll out the required hole size based on the size of screw choice.
p 5 - Re-attach the control head to the U-bracket utilizing the factory provided screws.
p 6 Connect the CAT5 harness to the RJ port located on the rear of the controller.
onsole Mountyou would like to mount the control head to a console, follow the instruction below.
p 1 Follow steps 1 and 2 for Control Head Mounting
p 2 Refer to the manual included with your console for specic information on mounting the control head.
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
6/10
ower Supply Mounting & Installation
llow the instructions below when mounting and installing the 4200 power supply. To avoid warranty concerns, refrain fr
ounting the power supply in a moist location.
Mounting
p 1- Select a dry location to mount the power supply.
p 2- Mount the power supply in the desired location using 4 self-tapping screws. If you wish to use machine screws, sim
ll out the required hole size based on the screw choice.
Wiring
p 1- Locate the 8 Pin terminal blocks provided.
p 2- Insert the six blocks in their desired location. Press down rmly to insure connectivity.
p 3- Using a at head screw driver, rmly secure the copper portion of each wire to its desired port. Make sure to follox current rating per output.
p 4- Firmly secure the Cat5 harness into the marked RJ45 port.
p 5- Apply power and ground to the 2 port Molex terminal block. Using a Phillips screw driver rmly clamp down on
pper portion of the wire. A poor connection may result in warranty concerns.
p 6- Ensure that each 30 amp fuse is not loose and is rmly connected. If a fuse is removed or blown an LED will
minate indicating a replacement fuse is needed.
The USB port is used for control by a computer system. The software package will be available for download in 2014.
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
7/10
Wiring Diagram
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
8/10
Confguration RecordUse this document to record the products connected to each outlet to assist when programming the
control head with the provided software package.
Outputs:
_______________________________
_______________________________
_______________________________
_______________________________
_______________________________
_______________________________
_______________________________
0______________________________
1______________________________2______________________________
3______________________________
4______________________________
5______________________________
6______________________________
7______________________________
1-24____________________________
5-28____________________________9-32____________________________
nputs:
A_______________________________
_______________________________
_______________________________
D_______________________________E_______________________________
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
9/10
Control Head Programing
he software program is downloaded directly from Feniex.com
is found in the literature tab on the 4200 page. File size is 50MB so the download my take a while depending on your
ternet speed.
Helpor help on how to use the software please click the help button located on the top bar. You will nd informative
deos on how to program every function of the 4200 software system.
-
7/30/2019 Feniex 4200 Controller Instruction Manual V2
10/10
Bluetooth
The Feniex 4200 has the option of being controller via a smart phone or tablet. To enable this feature you will require
he Feniex inline Bluetooth module. Follow the below installation instructions below to pair the 4200 with a smart phon
or tablet.
Step 1- Connect the RJ45 cable exiting the 4200 power supply to one end of the BT module. Connect the other end to
he 4200 controller and follow the marking on the Bluetooth unit for proper connectivity.
Step 2- Locate the push button switch.
Step 3- Locate the pairing button on the software program screen.
Step 4- Before clicking the pairing button, press and hold the switch located in step 2.
Step 5- Click the pairing button on the software screen.
Step 6- Release the switch located in step 2 once pairing is complete. (your device is now connected)