(fig.1) for safety and proper operation, your fixture must ...€¦ · 1. fixture is located in a...

LEDDusk To Dawn 10,000 Lumen Barn Light

SKU No: 3569203MODEL No: M-D00001L-LB

PACKAGE CONTENTS

WALL MOUNT INSTRUCTIONS

ADDITIONAL WARNINGS

5 YEAR LIMITED WARRANTYThis product is guaranteed against failure due to factory defects in materials or workmanship for five (5) years from the date of purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of the product includes, but is not limited to: washing the product, using in extreme weather conditions, opening the product, or trying to remodel the product. Important: this warranty is only valid if the product has been purchased through an authorized reseller. Returns and/or warranty replacements must be processed at the original place of purchase.

WARNINGS

WARNING: This product needs to be grounded properly in amanner consistent with local electrical codes and/or the

current National Electric Code (NEC). If the installer cannot determine if this product is properly grounded, has no ground wire, or is unfamiliar with electrical wiring methods of properly grounding fixture, consult a qualified electrician. WARNING: Do NOT look directly at LED light sources.

WARNING: Use only in 110-240v, 60Hz circuits.

WARNING: To prevent wire damage, do not expose wiring to edges of sheet metal or other sharp objects.

WARNING: TO AVOID ELECTRIC SHOCK,DISCONNECT POWER BEFORE INSTALLING

CUSTOMER SERVICE

For questions regarding this product, please e-mail us at [email protected].

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.

Revision Date: 03-01-2019

TROUBLESHOOTING GUIDE

CLEANING INSTRUCTIONS

Disconnect power to fixture before cleaning. Using a soft cloth, clean the fixture using a mild, non-abrasive glass cleaner. DO NOT use solvents. DO NOT use cleaners containing abrasive agents. NEVER spray liquid cleaner directly onto the LEDs, fixture or wiring.

Before starting work to connect the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.

2.0 in.5,1 cm

2.0 in.5,1 cm

5.75 in.14,6 cm

CAUTION: Personal injury can occur, along with damage to the fixture and/or mounting surface may result if the

fixture is pulled from the surface. To prevent premature failure from overheating, fixture should only be installed in environments where the operating temperatures are between -40° to 122°F (-40° to 50° C). Do not install in a totally enclosed (no ventilation) area.

WARNING: This product may represent a possible shock or fire hazard if improperly installed or mounted. Products should

be installed following these instructions, local electrical codes and/or the current National Electric Code (NEC).

WARNING: DO NOT alter or disassemble the fixture it is completely enclosed and does not contain replaceable or

serviceable parts.

DIMMING

• DO NOT USE THIS FIXTURE WITH DIMMERS.Doing so will void the warranty of this product.

LED Facts:Color Temperature: 4000K (Bright)Operating Voltage: 110-240vLED Life: 50,000 hours

14

2 3

Before beginning, disconnect the power to the junction box. If replacing an existing fixture with more than two wire leads, make a note as to where they were connected.

MOUNTING ARM INSTALLATION

1. Unscrew both wire compartment cover bolts and remove the wire compartment cover (Fig. 1).


Do not to pinch the wires while installing the fixture onto the mounting arm.

1. Remove both wire compartment cover bolts and remove the wire compartment cover (Fig.1).

2. The wire compartment cover has two knockouts on it. For wall mount installations, remove the knockout on the back side (Fig. 2). If mounting the fixture to a pole using conduit or a strain relief, remove the bottom knock out (Fig. 3). Attach the non-metallic clamp connector, strain relief or conduit connector where the knock-out was removed. Feed the wires through the connectors prior to re-attaching the wire compartment cover.

4. For mounting to the side of a building or a pole, (other than an outdoor mounting arm*) attach the light by using the 3 included large screws at the mounting base (Fig. 5). Predrill mounting holes into the surface and install the appropriate anchors prior to mounting the fixture to surfaces other than wood. After all 3 screws are tightened and are secured to the surface, restore power.

9.25 in.23,5 cm

12.5 in.31,8 cm

12.5 in.31,8 cm

This fixture is rated for indoor/outdoor use.

Mount fixture between 8 ft. and 12 ft. off the ground.Electrical requirements can be found on fixture. Use with a Minimum 90° supply conductors.

This unit has a dusk-to-dawn sensor that automatically turns the light on at dusk and off at dawn.

WARNING: Do NOT mount on ground.

SAFETY AND PRECAUTIONS

1. Suitable for indoor and outdoor locations.2. Do NOT touch LEDs.3. Do NOT look directly at LED light sources. 4. The LED modules used in this fixture are not serviceable.5. Do NOT make contact or install fixture while making contact with water.6. NOT suitable for ground installations. Mount between 8 ft. to 12 ft. off the ground.7. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.8. Suitable for use in operating environments ranging between -40° F to 122° F (-40° C to 50° C). 9. Do NOT leave bare wires exposed outside of the electrical connections.10. Electrical requirements can be found on back of the fixture.11. If unsure how to install a light fixture, call a qualified electrician.

• Shut off power at the circuit breaker or fuse box before installing or servicing this fixture.

Fig. 1

Fig. 3

Fig. 4

Fig. 2

Fig. 5

Fig. 7

Fig. 6

Fig. 8

Fig. 9

* Outdoor mounting arm sold separately.

3. For mounting on a standard 2 in. diameter mounting arm*, slide the fixture mounting base carefully over the mounting arm while tucking the wires into the mounting arm until it is fully seated against the fixture (Fig. 7). Use the included mounting arm crossbar to secure the light to the mounting arm by aligning the holes (Fig. 8). Tighten both bolts down

Fixture does notturn on.

Problem Probable Cause Solution

Light comes on duringthe daylight hours.

Light cycles ON and OFFcontinuously (strobelight effect).

1. Dusk-to-dawn sensor is detecting reflected light from the security light.

1. Change the position of the light head. Reposition lightaway from the reflecting surface.

2. Place a small piece of black electrical tape over the bottomhalf of the dusk-to-dawn sensor.

3. Move the light to a different location where the results are better.

1. Bad connection.2. Faulty switch.3. Power is off.

1. Fixture is located in ashaded area; dusk-to-dawnsensor is detecting darkness.

1. Check wiring connections.2. Test switch or replace it.3. Verify power supply is on.

1. Shine a light at the dusk-to-dawn sensor. If the securitylight immediately shuts off, then the fixture is located inan area that is too dark to allow enough light to enter the sensor. The light will need to be relocated.

Circuit breaker trips or fuseblows when light is turned on.

1. Discontinue use immediately.

1. Call an electrician.

1. Call an electrician.2. Dusk-to-dawn sensor may be malfunctioning.


Diffuser

1xMountingArm Crossbar

2xWireCompartmentCover Bolts

3xLargeMountingScrew

3xWire Nuts

LED Module

Ground Wire

Dusk to DawnSensor

Wire Compartment Cover

WireCompartment

Wire CompartmentCover Bolts

3. For safety and proper operation, your fixture must be properly grounded. Connect the yellow and green ground wire attached to the fixture with the ground wire from the junction box together with a wire nut (Fig. 4). If you are unfamiliar with the methods of properly grounding your fixture, consult a qualified electrician.

Using the remaining included wire nuts, connect the white supply wire to the white (NEUTRAL) fixture wire and the black supply wire to the black (LIVE) fixture wire.

Tuck all connections back into wirecompartment prior to mounting.


Using the included wire nuts, connect the white supply wire to the white (NEUTRAL) fixture wire and the black supply wire to the black (LIVE) fixture wire.

Tuck connections back into the mounting arm as the openingpasses over them.

LEDDusk To Dawn10,000 Lumen Utility Light

MODEL No: BL-L10000D

PACKAGE CONTENTS


ADDITIONAL WARNINGS


WARNINGS

WARNING: This product needs to be grounded properly in a manner consistent with local electrical codes and/or the





CUSTOMER SERVICE

For questions regarding this product, please e-mail us at [email protected].

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The user is cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from thatof the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.






2.0 in.5,1 cm

2.0 in.5,1 cm

5.75 in.14,6 cm


fixture is pulled from the surface. To prevent premature failure from overheating, fixture should only be installed in environments where the operating temperatures are between -40° to 122°F (-40° to 50° C). Do not install in a totallyenclosed (no ventilation) area.




serviceable parts.

DIMMING



14

2 3









9.25 in.23,5 cm

12.5 in.31,8 cm

12.5 in.31,8 cm

This fixture is rated for indoor/outdoor use.





1. Suitable for indoor and outdoor locations.2. Do NOT touch LEDs.3. Do NOT look directly at LED light sources.4. The LED modules used in this fixture are not serviceable.5. Do NOT make contact or install fixture while making contact with water.6. NOT suitable for ground installations. Mount between 8 ft. to 12 ft. off the ground.7. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.8. Suitable for use in operating environments ranging between -40° F to 122° F (-40° C to 50° C).9. Do NOT leave bare wires exposed outside of the electrical connections.10. Electrical requirements can be found on back of the fixture.11. If unsure how to install a light fixture, call a qualified electrician.


Fig. 1

Fig. 3

Fig. 4

Fig. 2

Fig. 5

Fig. 7

Fig. 6

Fig. 8

Fig. 9


















1. Call an electrician.2. Dusk-to-dawn sensor may be malfunctioning.


Diffuser




3xWire Nuts

LED Module

Ground Wire

Dusk to DawnSensor


WireCompartment










PACKAGE CONTENTS


ADDITIONAL WARNINGS

5 YEAR LIMITED WARRANTYThis product is guaranteed against failure due to factory defects in materials or workmanship for five (5) years from the date of purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of the product includes, but is not limited to: washing the product, using in extreme weather conditions, opening the product, or trying to remodel the product. Important: this warranty is only valid if the product has been purchased through an authorized reseller.

WARNINGS






CUSTOMER SERVICE

For questions regarding this product, please contact us at 303.652.6164, M-F 7am - 4pm MT or e-mail us at [email protected].







2.0 in.5,1 cm

2.0 in.5,1 cm

5.75 in.14,6 cm






serviceable parts.

DIMMING


LED Facts:Lumens: 10,000Color Temperature: 4000KCRI: 80Efficacy (Lumens Per Watt): 80 Operating Voltage: 110-240vRated Watts: 125WPower Factor: 0.9LED Beam Angle: 120°LED Life: 50,000 hoursOperating temperature: -40° to 122°F (-40° to 50° C)

14

2 3



1. Unscrew both wire compartmentcover bolts and remove the wirecompartment cover (Fig. 1).




2. The wire compartment cover has two knockoutson it. For wall mount installations, remove theknockout on the back side (Fig. 2). If mounting thefixture to a pole using conduit or a strain relief,remove the bottom knock out (Fig. 3). Attach thenon-metallic clamp connector, strain relief orconduit connector where the knock-out wasremoved. Feed the wires through the connectorsprior to re-attaching the wire compartment cover.

4. For mounting to the side of a buildingor a pole, (other than an outdoormounting arm*) attach the light byusing the 3 included large screws at themounting base (Fig. 5). Predrillmounting holes into the surface andinstall the appropriate anchors prior tomounting the fixture to surfaces otherthan wood. After all 3 screws aretightened and are secured to thesurface, restore power.

9.25 in.23,5 cm

13.25 in.33,7 cm

13.25 in.33,7 cm

This fixture is IP65 rated and therefore suitable for indoor/outdoor use in wet locations.


This unit has a dusk-to-dawn sensor that controls that automatically turns the light on at dusk and off at dawn.



1. Suitable for indoor and outdoor wet locations.2. Do NOT touch LEDs.3. Do NOT look directly at LED light sources. 4. The LED modules used in this fixture are not serviceable.5. Do NOT make contact or install fixture while making contact with water.6. NOT suitable for ground installations. Mount between 8 ft. to 12 ft. off the ground.7. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.8. Suitable for use in operating environments ranging between -40° F to 122° F (-40° C to 50° C). 9. Do NOT leave bare wires exposed outside of the electrical connections.10. Electrical requirements can be found on back of the fixture.11. If unsure how to install a light fixture, call a qualified electrician.


Fig. 1

Fig. 3

Fig. 4

Fig. 2

Fig. 5

Fig. 7

Fig. 6

Fig. 8

Fig. 9

















1. Call customer service at 303.652.6164.2. Call an electrician.

1. Call customer service at 303.652.6164.2. Call an electrician.

2. Dusk-to-dawn sensor may be malfunctioning.


Diffuser




3xWire Nuts

LED Module

Ground Wire

Dusk to DawnSensor


WireCompartment


3. For safety and proper operation, yourfixture must be properly grounded. Connectthe yellow and green ground wire attached tothe fixture with the ground wire from thejunction box together with a wire nut (Fig. 4).If you are unfamiliar with the methods ofproperly grounding your fixture, consult aqualified electrician.








PACKAGE CONTENTS


ADDITIONAL WARNINGS


WARNINGS






CUSTOMER SERVICE

For questions regarding this product, please contact us at 303.652.6164 M- F 7am - 4pm MT.







2.0 in.5,1 cm

2.0 in.5,1 cm

5.75 in.14,6 cm






serviceable parts.

DIMMING



14

2 3









9.25 in.23,5 cm

12.5 in.31,8 cm

12.5 in.31,8 cm

This fixture is IP65 rated and therefore suitable for indoor/outdoor use in wet locations.





1. Suitable for indoor and outdoor wet locations.2. Do NOT touch LEDs.3. Do NOT look directly at LED light sources. 4. The LED modules used in this fixture are not serviceable.5. Do NOT make contact or install fixture while making contact with water.6. NOT suitable for ground installations. Mount between 8 ft. to 12 ft. off the ground.7. This product is inspected prior to shipping. Do not use if product is cracked, broken or missing parts.8. Suitable for use in operating environments ranging between -40° F to 122° F (-40° C to 50° C). 9. Do NOT leave bare wires exposed outside of the electrical connections.10. Electrical requirements can be found on back of the fixture.11. If unsure how to install a light fixture, call a qualified electrician.


Fig. 1

Fig. 3

Fig. 4

Fig. 2

Fig. 5

Fig. 7

Fig. 6

Fig. 8

Fig. 9


3. For mounting on a standard 2 in.diameter mounting arm*, slide the fixturemounting base carefully over themounting arm while tucking the wiresinto the mounting arm until it is fullyseated against the fixture (Fig. 7). Use theincluded mounting arm crossbar tosecure the light to the mounting arm byaligning the holes (Fig. 8). Tighten bothbolts down





1. Dusk-to-dawn sensor isdetecting reflected lightfrom the security light.







1. Shine a light at the dusk-to-dawn sensor. If the securitylight immediately shuts off, then the fixture is located inan area that is too dark to allow enough light to enter thesensor. The light will need to be relocated.


1. Discontinue useimmediately.


1. Call an electrician.2. Dusk-to-dawn sensor maybe malfunctioning.


Diffuser




3xWire Nuts

LED Module

Ground Wire

Dusk to DawnSensor


WireCompartment





2. For safety and proper operation, your fixture must be properly grounded.Connect the yellow and green ground wire attached to the fixture with the groundwire from the junction box together with a wire nut (Fig. 6). If you are unfamiliarwith the methods of properly grounding your fixture, consult a qualifiedelectrician.



(fig.1) for safety and proper operation, your fixture must ...€¦ · 1. fixture is located in a...

Documents