fist-gr3 odf system - cynerpro · the quareo rack controller is a networked device that provides...

FIST-GR3 ODF System

Featuring Quareo® Technology

2015 ORDERING GUIDE | 4TH EDITION

Contents

Quareo Physical Layer Management System 4

Quareo Middleware 5

Quareo Software 6

FIST-GR3 Rack 7

FIST-GPS Shelf featuring Quareo Technology (FIST-GPSQ) 7

Connection Point Identification (CPID) 7

Adapter Packs and Modules 7

Quareo Rack Controller 7

Example Application of a Two Rack Cross Connect 8

FIST-GPSQ Shelf Featuring Quareo Technology (FIST-GPSQ) 9

Benefits of Tray Patching 10

FIST-GPSQ Standard Kit Content 11

MPO Modules 13

Adapter Packs 15

FIST-GR3 Rack 16

Dimensions 17

Racks 17

Quareo Rack Controller 19

Quareo Managed Patch Leads and Multi-Fiber Cable Assemblies 20

FIST-GR3


Quareo Physical Layer

Management System Businesses and organizations worldwide are more dependent on their physical layer than

ever before. From computers, phones and wireless devices, to alarm systems, security

cameras and video conferencing, today’s network physical layer touches virtually every

device inside an organization. Security of the physical layer also has become a top

concern among network and data center managers, especially in healthcare, financial and

mission-critical organizations where data is required to be secure.

CommScope’s Quareo physical layer management system, with its Quareo Connection Point Identification (CPID) hardware technology, delivers full

knowledge and visibility of the physical layer. These solutions enable higher network availability, while lowering network costs, by integrating full

visibility of the physical layer into existing network management applications—all the way from the data center to the desktop. Quareo is helping

network and data center managers bridge the gap between network management and physical layer management, transforming the physical layer

into a strategic asset and revolutionizing the way networks are managed and controlled. By providing a real-time comprehensive picture of every

connection point in the physical layer, physical layer management significantly improves productivity and efficiency of physical layer management

and maintenance processes while reducing costly downtime and operating costs.

For more information on the Quareo physical layer management system, visit www.commscope.com.

4 For more information, visit commscope.com

FIST-GR3


Quareo Middleware The Quareo system is an Automated Infrastructure Management (AIM) platform which leverages a common middleware to drive and collect port

level information from Quareo (CPID enabled) hardware. The Middleware approach and architecture of the Quareo system allows customers the

flexibility to use the automated hardware to augment and leverage existing physical layer documentation, connection level details to support logic

determinations, 3rd party management software platforms and custom use cases. The Quareo middleware API can host multiple connections to

various software systems allowing for consistent, uniform updates of the physical layer connectivity information. The same Quareo Middleware

drives communications for the purpose built Quareo Software GUI as a stand-alone tool.

Automated port status: Quareo Hardware (CPID enabled) in combination with Quareo Middleware provides the automated port status of whether a port is

vacant and available for use or populated with a patch cord. When Quareo Cables are used, the cable assembly information is provided with the port status

information. Quareo Assemblies have unique serial numbers assigned in manufacturing which is programmed into the CPID along with PN and other details

pertinent to the assembly/component. This CPID information allows correlation of the serial numbers to positively validate both ends/ports of the patch

connection, and align system requirements/parameters (e.g.: circuit length budgets, Color coding, polarity, performance categories, etc.).

LED Controls: Quareo (CPID) enabled equipment ports have bi-color LEDs for use in works orders and guidance as indicators. Within a change control process the

identified ports for connection or removal of a cable assembly can have the LEDs turned on with appropriate colors and flash patterns, identifying the ports for either

insertion or removal of cables, eliminating guesswork by field technicians, providing a reliable identification of the ports involved in the work actions.

DBMS Use Cases

3rd PARTY APPLICATION • Auto Documentation and Updates

(DCIM, NMS) • Port level Activity Monitoring

• Port level Security

QUAREO MIDDLEWARE LAYER • Port Status

• Port Level Details HTTP REST API(s) SNMP MIB(s)

CPID Work Task • Change Control processes

Connectivity Management • Circuit Level Integrity Quareo Device Quareo Device

Discovery management • Cable Assembly Details

QUAREO ENABLED • Assembly Serial Number

DEVICES Correlation

VIA HTTP • Change control indicators

• LED Guidance


FIST-GR3


Quareo Software The Quareo Software GUI supported by the Quareo Middleware is a purpose-built, stand-alone, server software application designed to document

and administer both passive and active network connectivity infrastructure. The Quareo software enables management of various levels of network

components from existing brownfield infrastructure to CommScope’s traditional and automated physical layer management solutions.

As part of the Quareo physical layer management system, Quareo software enables immediate notification and response to changes in

connectivity and automatically records the configurations of the physical layer cabling system and its devices with accurate documentation.

Features • Accountability of assets by location and date • Availability of assets and utilization is improved • Reduced operational costs • Best practice and regulatory requirements are more easily attained • Network problems are more easily diagnosed and corrected • Security is greatly enhanced • Remote visibility of the physical layer • DoD/DISA/JITC tested


FIST-GR3


FIST-GR3 Rack All-purpose, easy-to-assemble FIST-GR3 racks accommodate the FIST fiber management system. The racks

allow superior management and storage of pigtail and patch cord overlengths. The rack offers flexible shelf

spacing and accepts a range of accessories such as panels and doors to complete the installation.

The rack houses the FIST-GPSQ shelves for splicing and patching. The rack also

houses the rack controller to manage the FIST-GPSQ shelves.

FIST-GPS Shelf featuring Quareo Technology (FIST-GPSQ) The FIST-GPSQ shelves feature the FIST fiber management system and provide a platform for patching

and splicing within a rack environment, using the Quareo physical layer management technology.

The shelves house FIST splice and patch trays with Quareo CPID enabled adapter packs. The

shelves mount in FIST-GR3 racks.

Connection Point Identification (CPID) CommScope’s CPID technology provides a unique identifier for every Quareo enabled component in

the network – enabling immediate recognition of a patch cord upon installing or removing. CPID

gives network operators complete visibility to all connection events in the network and provides

detailed information on the network elements being used.

Adapter Packs and Modules Adapter packs are designed to provide easy connector insertion/removal, and clearer adapter port

identification. Adapter packs are available in 24-fiber (12 duplex) LC, 12 fiber SC*, MPO-LC

modules or eight MPO adapter pack configurations. Each tray supports one adapter pack, for a

total of six adapter packs per shelf. These adapter packs can be included with the shelf.

* Under development. Contact CommScope for information on availability of the SC variant.

Quareo Rack Controller

The Quareo rack controller is a networked device that provides power and communication means to the FIST-

GPSQ shelves, and allows communication over the LAN network with the Quareo software or middleware.


FIST-GR3


Example Application of a Two Rack Cross Connect

NETWORK

CONNECTION

One CAT6 ethernet

cable required per rack

controller. To be

connected to the

network via a router or

switch (likely outside

the ODF room).

GR3 RACK

Rack Sideducts Doors

CPID CORDS

Quareo Managed

Patch Cords; matching

CPID information at

both ends

RACK CONTROLLER

One Q-GF1-CTR Rack

Controller can handle 1

rack of up to 16 subracks.

Requires external

power supply and

network connection

Power and

communication cabling to each shelf using a star topology. Each controller port to be connected to the corresponding shelf.

FIST-GPSQ -

Managed Shelf


FIST-GR3


FIST-GPSQ Shelf Featuring Quareo Technology (FIST-GPSQ) FIST-GPSQ shelves feature the FIST fiber management system and provide a platform for patching

and splicing within a rack environment, using the Quareo physical layer management technology. The shelves house FIST splice and patch trays with Quareo CPID enabled adapter packs,

available in LC, SC* and MPO. In addition different value adding modules are available

including LC-MPO and precabled solutions.

The shelves mount in FIST-GR3 racks.

* Under development. Contact CommScope for information on availability of the SC variant.

Quareo enabled • Each connector position inside the FIST-GPSQ shelf can read CPID information from the Quareo

enabled patch cords. This enables the shelf to discover all connector insertion and removal

events, and automatically document connections in the Quareo ICM software or middleware. • The FIST-GPSQ shelf itself, each tray inside the shelf, and each connector position inside

the trays are equipped with LEDs. These LEDs help to guide technicians to the right patch

ports, can give instant feedback during work order execution, and can visualize alarm

conditions on unplanned connector insertions or removals.

Features • Patching, using patch cords, connectorized breakout or intrafacility cables • Splicing loose tube cables, non-connectorized intrafacility or breakout cables to

pigtails and patching these pigtails to patch cords • Full patching capability on the tray and between trays in one shelf • Use of connectorized cables allows repair of pigtails • Kits available to attach cables at the side or back of shelf • Wrap-around side panel and pigtail guide for easy re-patching • Can be installed in CommScope’s FIST-GR3 rack • Shelves are shipped with the maximum number of trays and adapter packs already installed,

or can be empty for use with Quareo cabled modules


FIST-GR3 Featuring Quareo® Technology

Benefits of Tray Patching • Clean: Both sides easily accessible

for cleaning adapters • Safe: Laser light oriented perpendicularly

to the operator • Accessible: Full front access at both sides

of connection • Visible: Patch cords do not hamper

access or visibility of ports • Reconnection to other positions in the same tray or

shelf does not result in uncontrolled overlengths

• Bend controls guide and protect the pigtail

cable and ensure controlled cable routing • Manipulation of patch cords does not

cause transient losses • Secure: because of their position in the

trays, connectors are better protected

than in some front facing patch shelves

Dimensions, Configurations

and Capacities

Dimensions in mm:

Height: 125 (3HU)

Width: 385

Depth: 280

Tray Configuration

LC

Co

nn

ect

o

r

SC

MPO

Con

nect

or

LC

SC

MPO

Patch-Patch (AA) Splice-Patch (AX) Module (MA-AM)

Future option Future option Future option

Future option

N/A N/A

Connector Capacity

Tray Shelf Rack (14 Shelves)

24 144 2016

12 72 1008

8 48 672


FIST-GR3


FIST-GPSQ Standard Kit Content

Features • Metal chassis with drawer • Mounting brackets • Drawer includes:

-- 6 trays

-- 2 tray support wedges

-- Hook and loop strap to secure the trays

-- Bend control(s) at the patching side for patch configurations

• Splice/patch versions include foam and tie-wraps to fix the cable elements (loose tubes, break-out cable, intra-facility subunits) onto the trays • Trays which include:

-- Adaptor packs (as configured) -

- Pigtails if prefibered option

-- Splice protector holder (only if configured as splice tray)

-- Splice protectors (only if pigtail and SMOUV option is included)

• One or two trumpets for guiding pigtails as they exit the shelf • Metal front cover:

-- 125 mm high version hingeable and removable cover

• Mounting screws and nuts • Installation instructions


FIST-GR3


Ordering Information

FIST – GPSQ – Q - XX X XX - 6 Chassis Type

Q

15” 3 ETSI HU

Connector Type (patch side)

Recommended for patch

patch applications (AA)

LU LC universal (black)

SU SC universal (black)

MU MPO - 12F universal (black)

M1 MPO-24F (aqua) Required specification for prefibered

splice-patch (Ax)

L1 SM - LC - UPC - grade C

L2 SM - LC - APC - grade C

LF SM - LC - UPC - grade B

LG SM - LC - APC - grade B

L5 MM - LC - UPC

S1 SM - SC - UPC - grade C

S2 SM - SC - APC8 - grade C

S3 SM - SC - APC9 - grade C

SF SM - SC - UPC - grade B

SG SM - SC - APC8 - grade B

S5 MM - SC - UPC

M1 SM - MPO12

M2 SM - MPO24

M3 MM - MPO12

M4 MM - MPO24

NN No connector specified

Contact CommScope for SC connector availability.

Adapter Pack Quareo Enablement

O Empty

L Simplex Both Sides

D Duplex Both Sides

EDuplex Patch Side Only F

Simplex Patch Side Only

6 Trays

Tray Options (patch islands & modules)

Right of Left of

shelf (1) shelf (2)

AA Patch only

AI IA Splice patch - ANT - prefibered pigtails

AJ JA Splice patch - ANT - prefibered pigtails

AE EA Splice patch - SMOUV - no pigtails

AF FA Splice patch - ANT -no pigtails

AM MA Prepared to accept LC-MPO and

precabled modules(3)

1 Patch cords or cables leave shelf to

right; patch fiield to left of tray

2 Patch cords or cables leave shelf to

left; patch fiield to right of tray

3 In this configuration modules

have to be ordered separately

Items to be ordered separately: • Fusion splice protectors

(according to type of tray chosen)

• Pigtails, patch cords, breakout

and IFC (OCI, OCJ, OCIP)

• Group termination unit if non-connectorized

breakout cable is to be used (FIST-GTU2)


FIST-GR3


MPO Modules The MPO module offers a craft-friendly interface for connecting 24 LC connectors to an MPO adapter – enabling a rapid connection to electronics or

a fiber tie panel such as CommScope’s Rapid Fiber panel solution. Leveraging an MPO architecture, technicians can route and install higher fiber

counts faster and easier, while simplifying cable inventory and ordering requirements.

MPO modules are available for use in the FIST-GPSQ-shelf, using the “AM” or “MA” tray configurations.

• For the AM configuration, with patch cords leaving to the right, and MPO trunk feeding from the left of the rack, use a “left” module. • For the MA configuration, with patch cords leaving to the left, and MPO trunk cable feeding from the right of the rack, use a “right” module.

Specifications MPOptimate Performance

Multimode 12f MPO – LC:

Factory measured 0.35 dB loss maximum per MPO-LC OM4 module

Multimode 24f MPO – LC:

Factory measured 0.35 dB loss maximum per MPO-LC OM4 module

Singlemode Performance:

<0.75 dB @ 1310 nm/1550 nm

Insertion & Return Loss:

IL <= 0.35dB RL >= 27dB

Traceable:

Each module is uniquely identified and linked to factory measurement data

Standard Fiber Path:

Compatible with TIA 568-C.0-2 draft standard for Method A

24-Fiber Trunk Compatible:

Fiber path supports 24-fiber deployment

Pinned Cassettes:

MPO alignment pins are maintained inside the module, reducing damage risk

Used in Pairs:

Assures proper fiber map, polarity and location of MPO alignment pins



Ordering Information

LC-to-MPOptimate (2x12-fiber MPO)

Multimode MPOptimate (OM4); Loss (<0.35 dB @ 850 nm/1300 nm)

LC-to-MPOptimate (1x24-fiber MPO)

Multimode MPOptimate (OM4); Loss (<0.35 dB @ 850 nm/1300 nm)

LC-to-MPO (2x12-fiber MPO)

Singlemode; Loss (<0.75 dB) @ 1310 nm/1550 nm)

Module Adapter LC Port Monitoring Polarity Part Number

Orientation Color

Left Simplex A-A/B-B (Straight)

QE-MPM-24HPCUMLA

Right

Black

QE-MPM-24HPCUMRA

Left Duplex A-A/B-B (Straight)

QE-MPM-24HPDUMLA

Right

QE-MPM-24HPDUMRA

Left A-A/B-B (Straight)

QE-MPM-24HPFAHLA

Right

Aqua Duplex

QE-MPM-24HPFAHRA

Left A-B/B-A (Straight)

QE-MPM-24HPFAHLB

Right

QE-MPM-24HPFAHRB

Left A-A/B-B (Straight)

QE-MPM-24HPFAJLA

Right

QE-MPM-24HPFAJRA

Left

Aqua Duplex A-B/B-A (Flipped)

QE-MPM-24HPFAJLB

Right QE-MPM-24HPFAJRB

Left 10G HD

QE-MPM-24HPFAJLG

Right

QE-MPM-24HPFAJRG

Left Simplex UPC A-A/B-B (Straight)

QE-MPM-24HPKUELA

Right

Black

QE-MPM-24HPKUERA

Left Simplex APC A-A/B-B (Straight)

QE-MPM-24HPMUELA

Right

QE-MPM-24HPMUERA

Left

Blue Duplex UPC A-A/B-B (Straight)

QE-MPM-24HPCBELA

Right QE-MPM-24HPCBERA

Example of a MA tray configuration

using a “Right” module

Example of a AM tray configuration using a “Left” module

FIST-GR3


Adapter Packs Adapter packs will generally be fitted on the trays of a FIST-GPSQ shelf, but can also be ordered separately.

Universal adapter packs are designed to accept a variety of connector types, including singlemode and multimode, angled and ultra-polished

connections, allowing a network operator to support all variants of connector type within a single adapter pack, greatly simplifying ordering and

providing excellent future flexibility.. The flexibility of the black universal adapter pack helps service providers reduce ordering SKU’s and total

inventory requirements. The staggered adapter pack design helps installers access connectors without pinching or moving adjacent connections

and helps clearly identify individual fiber ports. One 24-fiber (12 duplex port) LC adapter pack can be installed per tray or one eight-port MPO

adapter pack (12- or 24-fiber MPO) per tray; up to six total adapter packs per shelf.

Description Part Number

Managed Adapter Pack, LC-LC Black, 24 fibers (24 simplex ports, managed both sides) QE-ADP-24HPLCS000

Managed Adapter Pack, LC-LC Black, 24 fibers (12 duplex ports, managed both sides) QE-ADP-24HPLCD000

Managed Adapter Pack, LC-LC Black, 24 fibers (12 duplex ports, managed patch side only) QE-ADP-24HPLCE000

Managed Adapter Pack, LC-LC Black, 24 fibers (24 simplex ports, managed patch side only) QE-ADP-24HPLCF000

Managed Adapter Pack, LC-LC Aqua, 24 fibers (12 duplex ports, managed both sides) QE-ADP-24HP0CD000

Managed Adapter Pack, LC-LC Blue, 24 fibers (12 duplex ports, managed both sides) QE-ADP-24HP0KD000

Managed Adapter Pack, LC-LC Green, 24 fibers (12 duplex ports, managed both sides) QE-ADP-24HP0MD000

Managed Adapter Pack, MPO-MPO Black, 96 fibers (8, 12F MPO, managed both sides) QE-ADP-96HPMPG000

Managed Adapter Pack, MPO-MPO Black, 96 fibers (8, 12F MPO, managed patch side only) QE-ADP-96HPMPF000

Managed Adapter Pack, MPO-MPO Aqua, 192 fibers (8, 24F MPO ports, managed both sides) QE-ADP-192HPMAG000

Managed Adapter Pack, MPO-MPO Green, 192 fibers (8, 24F MPO ports, managed both sides) QE-ADP-192HPMGG000


FIST-GR3


FIST-GR3 Rack All-purpose, easy-to-assemble FIST-GR3 and FIST-GR3F racks accommodate the FIST fiber management

system in a central office, head-end or customer premises environment.

Several versions of the rack are available: one series based on the ETSI standard (600 mm

wide); and one on the 15-inch standard (450 mm wide). With the addition of side ducts, total width of the rack framework varies between 600 and 1200 mm. Rack heights of 1.8 or 2.2

meters are available. All versions feature flexible shelf spacing and accept a range of

accessories such as panels and doors to complete the installation.

Both racks house connector panels and separate shelves for splicing, patching, equipment and devices. The racks allow superior management and storage of pigtail and patch cord overlengths.

** If you order a 19” frame, you will also need to order adapter

brackets to fit the 15” Quareo FIST-GPSQ shelf.

Features

Easy handling • Compact, efficient packaging means less waste • Easy to transport, store, handle and install due to compact design • Universal installation manual (drawings, no words) • Assembly requires only simple tools allowing faster installations than standard racks Flexibility • Compatible with CommScope’s FIST-GR2 racks • Accepts CommScope’s Quareo FIST-GPSQ shelves; FIST-GSS2/GPS2 and FIST-GSS3/GPS3 shelves • Depth and width in accordance with ETSI • ETSI mounting profiles with cage nuts for shelf mounting provided at rear of the rack for optimal access from the front • Optional units allow horizontal and vertical patch cord management and storage of excess patch cord overlength • Bend control on all fiber routing All-purpose rack • Structured division and distribution of cable elements • Wide variety of optional accessories • Extra cable attachment plates can be mounted in any location (top/bottom) in side duct • Easy access to cables, pigtails and jumpers during installation, maintenance and upgrade • Easy adaptation to specific applications by changing rack or shelf configuration, as well as routings of pigtails and jumpers • Various mounting options

-- Wall mounting, stand-alone or multiple side-to-side mounting

(optional kit) -- Back-to-back mounting • Various rack options to suit all application requirements

-- Different side ducts (150, 300 mm) with drums for proper fiber

management -- Different doors

-- Front mounting options

-- Depth extension kits

-- Overlength storage bays


FIST-GR3


Dimensions

Dimensions (mm) and capacity

Dimensions Capacity

Description H1 W2 D3

Height Units

Number of FIST Shelves

(ETSI)3

11 (3 HUs = 125mm = 5 ETSI HUs)

FIST-GR3(F)-R-X2-18 1800 - 300 64-8=56 14 (2 HUs = 88mm = 4 ETSI HUs)4

28 (1 HU = 44mm = 2 ETSI HUs)4

11 (3 HUs = 125mm = 5 ETSI HUs)

FIST-GR3(F)-R-X2-22 2200 - 300 80-8=72 14 (2 HUs = 88mm = 4 ETSI HUs)4

28 (1 HU = 44mm = 2 ETSI HUs)4

1 Rack height of 2.6m possible; for pricing, order quantities and availability please contact your CommScope sales representative

2 The width (600-1200mm) depends on the configuration: please contact your CommScope sales representative

3 The base duct included in the rack occupies 8 ETSI HUs. If the base duct is removed, extra shelves can be placed in the rack

4 Not available with Quareo technology D

Racks

All racks include: H

• 2 side ducts with integrated ETSI mounting profiles: manage and house cables, pigtails, patch cords

• Base duct occupies 8 ETSI height units

• Loose drums

W1 W2 W3

• Cable attachment plates and drum plates integrated into management panel WTOT

• Wall and back-to-back connection kits • Earthing kit • Adjustable feet • Installation instructions and footprint template • Rack painted (powder coated) light grey (RAL-7035)



Dimensions (in mm)

Side Duct (W1) Central Section

Side Duct (W3) Total Width

Height (H) Depth (D) Description1

(W2) (WTOT)

0 (pole) 600 0 (pole) 600 1800/2200 300 FIST-GR3-R-0/0-XX-2

0 (pole) 600 150 750 1800/2200 300 FIST-GR3-R-0/150-XX-2

0 (pole) 600 300 900 1800/2200 300 FIST-GR3-R-0/300-XX-2

150 600 150 900 1800/2200 300 FIST-GR3-R-150/150-XX-2

150 600 300 1050 1800/2200 300 FIST-GR3-R-150/300-XX-2

300 600 300 1200 1800/2200 300 FIST-GR3-R-300/300-XX-2

0 (pole) 450 150 600 1800/2200 300 FIST-GR3F-R-0/150-XX-2

0 (pole) 450 300 750 1800/2200 300 FIST-GR3F-R-0/300-XX-2

150 450 150 750 1800/2200 300 FIST-GR3F-R-150/150-XX-2

150 450 300 600 1800/2200 300 FIST-GR3F-R-150/300-XX-2

300 450 300 1050 1800/2200 300 FIST-GR3F-R-300/300-XX-2

1 For height, replace xx with 18 for 1800mm or 22 for 2200mm. For 2.6m racks, please contact your CommScope sales representative

Accessories

Description

FIST-ODF-MB2-QT/M-AS 3&4HU 15>ETSI Mounting Bracket to mount a 15” 3&4HU shelf into

an ETSI rack. Asymmetrical

FIST-ODF-MB2-QT/I-AS-FTB

3&4HU 15>19 Mounting Bracket to mount a 15” 3&4HU shelf into a 19” rack.

EG5331-000 Asymmetrical front to back mounting (not recommended)

**Doors, top covers, mounting brackets and storage bays are available. See GR3 ordering guide.



Quareo Rack Controller The Quareo rack controller is a networked device that provides power and communication

means to the FIST-GPSQ shelves, and allows communication over the LAN network with the

Quareo physical layer network documentation solutions.

Features • Controls up to 16 FIST-GPSQ shelves • Easy mounting inside GR3 rack top bar, or with separate mounting brackets • Built-in 10/100Mbit/s Ethernet switch for daisy chaining of different racks in a line up • 48VDC Power Supply with redundant A and B inputs

Specifications

Dimensions W x H x D 308mm x 42mm x 169mm (including led cover)

Weight 1.5kg

Power Supply 2 x 48V DC inputs A and B for redundancy

Fused and breaker protected

Power Consumption (Maximum) 28W, 1.5A

Rack Controller Mounting bar

Power Adapter

Power Supply & Communication Star topology, single connector per shelf.

to FIST-GPSQ Shelves Connects up to 16 shelves.

Cooling Natural convection cooling. No active cooling or fan.

Ethernet Built in Ethernet switch. 10/100 Mb/s.

2 x RJ45 connectors.

Connection Cable

Ordering information

Description Catalog Number

Quareo Rack Controller 1 Per GR3 Q-GF1-CTRFB00000

FIST-GR3 mounting bar for Quareo Rack Controller - 15”(450mm), including mounting brackets Q-GF1-ACCFGR30450

FIST-GR3 mounting bar for Quareo Rack Controller - ETSI size (600mm), including mounting brackets Q-GF1-ACCFGR30600

Power brick for Quareo Rack Controller. 100-240VAC to 48VDC. Power cord not included Q-GF1-ACCFPBR0000

Cabling kit to connect Quareo Rack Controller and 14 Quareo subracks, labelled 1 to 14 Q-GF1-ACCPCK0014

Cabling kit to connect Quareo Rack Controller and 8 Quareo subracks, labelled 1 to 8 Q-GF1-ACCPCK0008

Cable kit to connect Quareo Rack Controller and 1 Quareo subrack, 3.1m long Q-GF1-ACCPCK0001


FIST-GR3


Quareo Managed Patch Leads and

Multi-Fiber Cable Assemblies Different cable solutions are available to cable the FIST-GPSQ shelf. Depending on

the application and fiber count an optimal solution can be provided.

CommScope offers: • Quareo Managed patch Leads

-- Simplex and Duplex LC, SC* and MPO --

Made to length with increments of 10cm

• Multi-Fiber Cable Assemblies

-- Stranded and Ribbon cable

-- IFC, Trunk and microcable assemblies -

- Connectorised, stubbed or with fanout

-- Different Breakout lengths optimized for use in the GPSQ shelf, other

Quareo panels (QHDEP, Q4000, ....) and active equipment

Features

-- SC, LC connectors in PC or APC

-- MPO12 and MPO24 for 10/40/100 migration, MPOptimate performance

-- Multimode and singlemode (aqua and yellow)

-- Standard colors: aqua for multimode, yellow for singlemode

-- Standard materials: – Plenum – LSZH

-- Performance specifications: ANSI/TIA-568-C.3 and ISO 11801, Edition 2

for OM3/OM4 multimode, OS1 for singlemode

Contact CommScope to assist you in providing the best solution for your application.


FIST-GR3



www.commscope.com Visit our website or contact your local CommScope representative for more information. © 2015 CommScope, Inc. All rights reserved. FIST, Rapid Fiber, Quareo, MPOptimate and all trademarks identified by ® or ™ are registered trademarks or trademarks, respectively, of CommScope, Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products

or services. CA-319452.4-AE (12/15)

fist-gr3 odf system - cynerpro · the quareo rack controller is a networked device that provides...

Documents