File: Flex Fence instr pg1 of 2 (2018)

For easier installation, pockets are located every3 inches to secure the fence to each support pole.

YOU MAY ALSO NEED THE FOLLOWING TOOLS:Tape Measure • String • Chalk or Spray Paint • Mallet or Drill • Sharp Scissors (if cutting is required)

A - Lay out fence lineUsing tape measure lay out the radius. Chalk or paint the line where fence will be installed.

FlexTension Fence Kit #FT160-19 includes:160 ft Pocket Net Fence, 5 Stabilizing Poles, 14 Flex Poles, Installation Accessories

FlexTension Fence Kit #FT160-19-DLUX includes:160 ft Pocket Net Fence, 5 Stabilizing Poles, 14 Flex Poles, Installation Accessories, 19 Ground Sockets

featuring Pocket-NetTM Technology

Outfield FenceNEW

2 Set Pole Layout

160 ft., 19 poles (8.5 ft spacing)Use 5 reinforced poles as shown ( )

1 Set Pole Layout

100 ft. to Home Plate

Foul Line Foul Line

This can be a 2 ft.gateway if desired

Set 1

Set 1

Set 2

Set 2

Set 3

Foul Line Foul Line

B - Mark pole locationsStarting at foul line, mark 19 pole locations approx. 8.5 ft. apartfor each 160 ft. set.Note: If using multiple sets, mark end locations close together between each set. You can allow for openings 2 ft. wide between sets for a gateway, or keep them close for a fence with no gateway.(see 3 diagrams below)

314 linear ft.2 sets

157 linear ft.1 set

471 linear ft.3 sets

100 f

t 2

00 ft

. 3

00 ft

.

. . .

. . . .

. . . . . .

. . . . . .

. . .

. . . .

. . . . . .

. . . . . .

. . .

. . . . . . . . . . . . . . . .

320 ft., 38 poles (8.5 ft spacing)Use 10 reinforced poles as shown ( )

200 ft. to Home Plate

3 Set Pole Layout

These can be (2) 2 ft.gateways if desired

Foul Line Foul Line

. . . . . . . . . . . . . . . . . . .

. . . .

. . . . .

. . . . . . .

. . .

. .

. . . . .

. . . . .

. . . . . . .

300 ft. to Home Plate480 ft., 57 poles (8.5 ft spacing)Use 15 reinforced poles as shown ( )

Suggested positions when installing 2 or more fence rolls (L-R)A - Continuous run - set end poles side by side or tight overlap

B - Overlap gate - pass-thru.

First set 2nd Set

First set

First set

2nd Set

2nd Set

2 ft opening

(OVER)

repeat as neededfor 3rd set

Hint:For Faster Work,Drill Pilot Hole using ouroptional Auger - 1" dia.x 10" deep.

ALWAYS MakePilot HolesDrive Pilot HoleTool into groundwith hammer orrubber mallet.

Gently tapPilot HoleToolfrom right to leftto loosen &remove fromground.

Use the supplied SocketSetter and drive GroundSocket into the ground.

SocketSetter

Insert fencePole into socket

PilotHole

Make surethe Socket isflush with theturf line.Push Socket as far as

you can into ground.

InstallingFence Poles

directlyinto pilot

hole

Pilot Hole

UseRubber Malleton posts!

Ground Sockets

Installing Poles / Ground Sockets

1-800-969-5920 www.markersinc.cominfo@markersinc.com

http://www.markersinc.com/pocket-net-fence-system.aspx?utm_source=pdf&utm_medium=pdf&utm_campaign=flex-fencehttp://www.markersinc.com/pocket-net-fence-system.aspx?utm_source=pdf&utm_medium=pdf&utm_campaign=flex-fence

Stretch the material to the next post, locate the nearest pocket and repeat Steps A-B for all posts.

Raise the fence open pocket and slide the material approximately 12 inches over the post and cap combination. (Remaining material can be loosely draped over for now.)

Installing your Pocket-NetTM fencing is this easy!Start at foul line

After all Pocket Poles are installed...

It’s easy to replace damaged Pocket NetTM Fence

PULL TIGHT to next pocket PULL TIGHT to next pocket

Ground Level

Install 12” of fencingfor remaining

poles

Once you have successfully attached all of the required pockets, the material can be pulled down to the bottom end of each post. For best appearance, confirm that the fence is tightly stretched between each post and does not sag. Any excess fencing can be easily cut with sharp scissors.

Find the first opening or “post pocket” by running your hand along the bottom edge of the fence material; pull pocket open.

File: Pocket Net Fence instr pg2 of 2 (2018)

Gathering material 12” at the top of each pole will make it easier to stretch the material to the next one in line.

Proceed one pole at a time until entire roll looks like this

(excess fence is hanging down).

It’s as easy as pulling on socks!

Contact a Markers, Inc. representative, call 1-800-969-5920, Email: info@markersinc.comVisit us at www.markersinc.com

repeat this for each setnow you’re ready to play!

damaged fencing?

Create a new section with 2 poles and additional fencing.

Overhead view

cut out damaged fence

New section added

Larger new section added - replacing longer damaged sectionsEXISTING POLES

NEW POLE NEW POLE

STABILIZING POLES1 19

15510

1-800-969-5920 www.markersinc.cominfo@markersinc.com

http://www.markersinc.com/pocket-net-fence-system.aspx?utm_source=pdf&utm_medium=pdf&utm_campaign=flex-fence

letter-page1-flex fence instrletter-page2-flex fence instr