for roller conveyor systems opt104 · 2015-01-12 · for roller conveyor systems opt164 part number...
TRANSCRIPT
Photoelectronic Sensors
for Roller Conveyor Systems
OPT104Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 550 mmPotentiometer min 220...270 mmPotentiometer center 320...400 mmPotentiometer max 550...630 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -15...50 °CSwitching Outputs 1Switching Output Voltage Drop < 0,8 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic yesSingle Discharge yesBlock Discharge yesPneumatic Solenoid Valve Unit yesProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pinCable Length 88 cm
Mechanical Data
K04Valve no.19,2...28,8 VSupply Voltage Valve86 mACurrent Consumption Valve4...7 barOperating Pressure0,8 mmNominal Width20 NL/minNominal flow rate 1 -> 2100 NL/minNominal flow rate 2 -> 32× 8×1Supply line connector pipe4×1Working line connector pipe3/2-WayValve functionNCSwitching function
Pneumatic Solenoid Valve Unit
PNP NC
Connection Diagram No. 714Control Panel No. OP1Suitable Connection Technology No. 2 2sSuitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedIntegrated logicScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
Complementary ProductsAdapter OPT70N, 70S, 70S+
Switching Distance DeviationTypical characteristic curve based on Kodak white (90 % remission)
OPT
200 250 300 350 400 450 500 550 600
-70
-60
-50
-40
-30
-20
-10
0
10
Sr/mm
dS
r/m
m
Pot. = Potentiometer Setting
dSr = Switching Distance Change
black 6 % remission
grey 18 % remission
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
714 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT123Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 550 mmPotentiometer min 220...270 mmPotentiometer center 320...400 mmPotentiometer max 550...630 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 1Switching Output Voltage Drop < 1,5 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic noProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pin
Mechanical Data
PNP NO
Connection Diagram No. 712Control Panel No. OP1Suitable Connection Technology No. 2Suitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
Switching Distance DeviationTypical characteristic curve based on Kodak white (90 % remission)
OPT
200 250 300 350 400 450 500 550 600
-70
-60
-50
-40
-30
-20
-10
0
10
Sr/mm
dS
r/m
m
Pot. = Potentiometer Setting
dSr = Switching Distance Change
black 6 % remission
grey 18 % remission
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
1
4
3
A
2nc
712 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT144Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 550 mmPotentiometer min 220...270 mmPotentiometer center 320...400 mmPotentiometer max 550...630 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 1Switching Output Voltage Drop < 0,8 VPNP Switching Output/Switching Current 200 mAValve or Motor Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic yesSingle Discharge yesBlock Discharge yesOutput Magnetic Valve/Engine yesProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pinCable Length 88 cm
Mechanical Data
PNP NC
Connection Diagram No. 715Control Panel No. OP1Suitable Connection Technology No. 2 2sSuitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedIntegrated logicScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
Complementary ProductsAdapter OPT70N, 70S, 70S+
Switching Distance DeviationTypical characteristic curve based on Kodak white (90 % remission)
OPT
200 250 300 350 400 450 500 550 600
-70
-60
-50
-40
-30
-20
-10
0
10
Sr/mm
dS
r/m
m
Pot. = Potentiometer Setting
dSr = Switching Distance Change
black 6 % remission
grey 18 % remission
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
3
1
4
3
3
4
2
1
AMV
BZ
A
4
5
3
4
2
1
BZ
E
715
2nc
Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT164Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Retro-Reflex Sensor
Technical Data
Range 6500 mmReference Reflector/Reflex Foil RQ100BAMin. Distance to Reflector 100 mmSwitching Hysteresis < 15 %Light Source Red LightPolarization Filter yesService Life (T = +25 °C) 100000 hMax. Ambient Light 10000 LuxOpening Angle 5 °Two-Lens Optic yes
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 25 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 1Switching Output Voltage Drop < 0,8 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic noProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP54Connection M12 × 1; 4-pin
Mechanical Data
PNP NO
Connection Diagram No. 738Control Panel No. OP2Suitable Connection Technology No. 2Suitable Mounting Technology No. 420
Fully encapsulatedLarge working rangeRecognition of high-gloss and jet black objects
01
OP2
Ctrl. Panel
01 = Switching Status Indicator
Complementary ProductsReflector, Reflex Foil Feasible reflector distance
Reflector type, mounting distance
RQ100BA 0,25...6,5 mRE18040BA 0,1...4 mRQ84BA 0,25...5 mRR84BA 0,2...5 mRE9538BA 0,15...2 mRR50_A 0,15...3 mRE6040BR 0,2...2,5 mRE8222BA 0,25...1,8 m
ZRAE02B01 0,2...1,8 mZRME03B01 0,15...2 mRF505 0,15...1,9 mRF508 0,15...1,9 mRF258 0,15...1,5 mZRDF03K01 0,1...3,5 mZRDF10K01 0,1...4,5 m
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
1
2
3
A
4nc
738 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT229Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 760 mmPotentiometer min 250...300 mmPotentiometer center 400...550 mmPotentiometer max 760...900 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 1Switching Output Voltage Drop < 1,5 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic noProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pin
Mechanical Data
PNP NC
Connection Diagram No. 711Control Panel No. OP1Suitable Connection Technology No. 2Suitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
1
2
3
A
711
4nc
Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT231Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 760 mmPotentiometer min 250...300 mmPotentiometer center 400...550 mmPotentiometer max 760...900 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 1Switching Output Voltage Drop < 1,5 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic noProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pin
Mechanical Data
PNP NO
Connection Diagram No. 712Control Panel No. OP1Suitable Connection Technology No. 2Suitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
1
4
3
A
2nc
712 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT244-P06Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 550 mmPotentiometer min 220...270 mmPotentiometer center 320...400 mmPotentiometer max 550...630 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msOff-Delay 0...2 sTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 2Switching Output Voltage Drop < 0,8 VPNP Switching Output/Switching Current 200 mAValve or Motor Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic yesSingle Discharge yesOutput Magnetic Valve/Engine yesAutomatic roll cutoff yesProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pinCable Length 150 cm
Mechanical Data
PNP NC
Connection Diagram No. 733Control Panel No. OP1Suitable Connection Technology No. 2 2sSuitable Mounting Technology No. 420
Electronic background suppressionEnergy-saving trough automatic roll cutoffFully encapsulatedIntegrated logicScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
Complementary ProductsAdapter OPT70N, 70S, 70S+
Switching Distance DeviationTypical characteristic curve based on Kodak white (90 % remission)
OPT
200 250 300 350 400 450 500 550 600
-70
-60
-50
-40
-30
-20
-10
0
10
Sr/mm
dS
r/m
m
Pot. = Potentiometer Setting
dSr = Switching Distance Change
black 6 % remission
grey 18 % remission
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
1
3
4AMV
3
1
3
2
4A
E
4
5
1
3
2
4E
A
2nc
733 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT246Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 550 mmPotentiometer min 220...270 mmPotentiometer center 320...400 mmPotentiometer max 550...630 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 2Switching Output Voltage Drop < 1,5 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic noProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pin
Mechanical Data
PNP NO/NC antivalent
Connection Diagram No. 754Control Panel No. OP1Suitable Connection Technology No. 2Suitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
Switching Distance DeviationTypical characteristic curve based on Kodak white (90 % remission)
OPT
200 250 300 350 400 450 500 550 600
-70
-60
-50
-40
-30
-20
-10
0
10
Sr/mm
dS
r/m
m
Pot. = Potentiometer Setting
dSr = Switching Distance Change
black 6 % remission
grey 18 % remission
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
754 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT255Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 550 mmPotentiometer min 220...270 mmPotentiometer center 320...400 mmPotentiometer max 550...630 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -15...50 °CSwitching Outputs 1Switching Output Voltage Drop < 0,8 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic yesSingle Discharge yesBlock Discharge yesPneumatic Solenoid Valve Unit yesProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pinCable Length 100 cm
Mechanical Data
K04Valve no.19,2...28,8 VSupply Voltage Valve86 mACurrent Consumption Valve4...7 barOperating Pressure0,8 mmNominal Width20 NL/minNominal flow rate 1 -> 2100 NL/minNominal flow rate 2 -> 32× 8×1Supply line connector pipe4×1Working line connector pipe3/2-WayValve functionNCSwitching function
Pneumatic Solenoid Valve Unit
PNP NC
Connection Diagram No. 734Control Panel No. OP1Suitable Connection Technology No. 2 2sSuitable Mounting Technology No. 420
Electronic background suppressionIntegrated logicOPT255: block discharge can be executed withsignal level 24V (I>1mA)Scaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
Complementary ProductsAdapter OPT70N, 70S, 70S+
Switching Distance DeviationTypical characteristic curve based on Kodak white (90 % remission)
OPT
200 250 300 350 400 450 500 550 600
-70
-60
-50
-40
-30
-20
-10
0
10
Sr/mm
dS
r/m
m
Pot. = Potentiometer Setting
dSr = Switching Distance Change
black 6 % remission
grey 18 % remission
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
1
734 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT285Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 760 mmPotentiometer min 250...300 mmPotentiometer center 400...550 mmPotentiometer max 760...900 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 2Switching Output Voltage Drop < 1,5 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic noProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pin
Mechanical Data
PNP NO/NC antivalent
Connection Diagram No. 754Control Panel No. OP1Suitable Connection Technology No. 2Suitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
754 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT307Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 760 mmPotentiometer min 250...300 mmPotentiometer center 400...550 mmPotentiometer max 760...900 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -15...50 °CSwitching Outputs 1Switching Output Voltage Drop < 0,8 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic yesSingle Discharge yesBlock Discharge yesPneumatic Solenoid Valve Unit yesProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pinCable Length 88 cm
Mechanical Data
K04Valve no.19,2...28,8 VSupply Voltage Valve86 mACurrent Consumption Valve4...7 barOperating Pressure0,8 mmNominal Width20 NL/minNominal flow rate 1 -> 2100 NL/minNominal flow rate 2 -> 32× 8×1Supply line connector pipe4×1Working line connector pipe3/2-WayValve functionNCSwitching function
Pneumatic Solenoid Valve Unit
PNP NC
Connection Diagram No. 714Control Panel No. OP1Suitable Connection Technology No. 2 2sSuitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedIntegrated logicScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
Complementary ProductsAdapter OPT70N, 70S, 70S+
OPT
200 250 300 350 400 450 500 550 600
-70
-60
-50
-40
-30
-20
-10
0
10
Sr/mm
dS
r/m
m
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
714 Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice
Photoelectronic Sensors
for Roller Conveyor Systems
OPT89Part Number
These sensors have been specially designed for use inaccumulation roller conveyors. Their compact designallows for installation between rollers below the trans-port level. They are thus protected against mechanicaldamage.
Reflex Sensor
Technical Data
Range 550 mmPotentiometer min 220...270 mmPotentiometer center 320...400 mmPotentiometer max 550...630 mmSwitching Hysteresis < 15 %Light Source Infrared LightWave Length 880 nmService Life (T = +25 °C) 100000 hRisk Group (EN 62471) 1Max. Ambient Light 10000 LuxOpening Angle 5 °
Optical Data
Supply Voltage 18...30 V DCCurrent Consumption Sensor (Ub = 24 V) < 30 mASwitching Frequency 100 HzResponse Time 5 msTemperature Drift < 10 %Temperature Range -25...60 °CSwitching Outputs 1Switching Output Voltage Drop < 1,5 VPNP Switching Output/Switching Current 200 mAShort Circuit Protection yesReverse Polarity Protection yesOverload Protection yesLogic noProtection Class III
Electrical Data
Adjustment PotentiometerHousing Material PlasticFull Encapsulation yesDegree of Protection IP65Connection M12 × 1; 4-pin
Mechanical Data
PNP NC
Connection Diagram No. 711Control Panel No. OP1Suitable Connection Technology No. 2Suitable Mounting Technology No. 420
Electronic background suppressionFully encapsulatedScaled switching distance adjuster
30
05
OP1
Ctrl. Panel
05 = Switching Distance Adjuster30 = Switching Status/Contamination Warning
Switching Distance DeviationTypical characteristic curve based on Kodak white (90 % remission)
OPT
200 250 300 350 400 450 500 550 600
-70
-60
-50
-40
-30
-20
-10
0
10
Sr/mm
dS
r/m
m
Pot. = Potentiometer Setting
dSr = Switching Distance Change
black 6 % remission
grey 18 % remission
All dimensions in mm (1 mm = 0.03937 Inch)
1 = Transmitter Diode2 = Receiver Diode
1
2
3
A
711
4nc
Legend
Wire Colors according to DIN IEC 757
not connected
Test Input
Test Input inverted
Trigger Input
Analog Output
Ground for the Analog Output
Block Discharge
Valve Output
Valve Control Output +
Valve Control Output 0 V
Synchronization
Receiver-Line
Emitter-Line
Grounding
Switching Distance Reduction
Ethernet Receive Path
Ethernet Send Path
Interfaces-Bus A(+)/B(–)
Emitted Light disengageable
Magnet activation
Input confirmation
Contactor Monitoring
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
Pink
Green Yellow
Supply Voltage +
Supply Voltage 0 V
Supply Voltage (AC Voltage)
Switching Output (NO)
Switching Output (NC)
Contamination/Error Output (NO)
Contamination/Error Output (NC)
Input (analog or digital)
Teach Input
Time Delay (activation)
Shielding
Interface Receive Path
Interface Send Path
Ready
Ground
Clock
Output/Input programmable
Power over Ethernet
Safety Input
Safety OutputSignal Output
Spec
ificat
ions
are
sub
ject
to c
hang
e wi
thou
t not
ice