for sale a complete nostalgia drag racing setup for $40k€¦ · 2.200 intake, 1.750 exhaust 1200...
TRANSCRIPT
FOR SALE – A complete nostalgia drag racing setup for $40k
This is a complete racing package. Just tow it to the track and go racing.
Everything you will need to go down the track is included.
Will pass all tech inspections. All certifications are current.
Front Engine Dragster
RooMan (Keith Burgan) built in 2010
See the build from the first tube to the last paint spray and passes down the track: http://www.lever-family-
racing.com/lever-family-racing-home/family-vehicles/2010-front-engine-dragster
Currently running in the NDRL series in an 8.0 index Strange Rear End, Gun Drilled Axles
IHRA certified Specification 2.2 Professional through 4/23/2016 Torsion front suspension
NHRA certified 6.00 and slower valid through 05/07/2016 Wilwood Brakes
Full body custom hand formed aluminum Strange steering box
Custom paint job. This dragster has been in shows and won awards. It was and continues to be used for active racing and the paint has scratches and pebble dents.
Cold Fire fire suppression system from D J Safety
RPM Performance Data Collector with sensors for all 8 EGTs, Boost, Fuel Pressure, Water Temperature, Oil Pressure, Drive shaft RPM, Engine RPM
Pit stand and Dolly New rear tires in 2014
Engine Pontiac
Professionally built by Matt Shaff of Pro-formance Specialties
See multiple rebuilds for more power here: http://www.lever-family-racing.com/lever-family-racing-home/family-
vehicles/1978-pontiac-fire-bird/1978-pontiac-firebird-winter-projects-part-2
Engine features include:
400 Pontiac ram air III block 1970 Crankshaft RPM-455A400C 4340 Deck 10.240 light weight (70 pounds) Stroke 4.000 Forged Scraper Nitrated Custom built Venolia pistons and aluminum rods. Kauffman lifter valley brace Pistons: 4.155 Bore .990 Pin/Supply Pins & Spiro Locks Milodon 13900 Timing Gear Drive (Single idler) 2.200 intake notch/ 1.750 Exhaust notch 15cc Dish Includes Valve Notches Custom Ford Crank Hub from RCD Engineering 10.5 Comp. for Blown Alcohol 1.605 Compression Distance Intake Modified BDS Blower Intake Aluminum Rods: Big Block Chevy Big End and Pin Bore Ignition MSD AL6-2 (there are two complete setups) 6.635 Center – Center -.010 Aluminum
Block is only stock item remaining
Blower New Littlefield stripped anodized 8-71 blower
Bird Catcher Kauffman heads 74 CC head, 325CFM Port, 2.11/1.77 valve arrangement, Titanium retainers, H-11 springs and 600 series valves
Injector hat Mechanical fuel injection (tune-up by Spud Miller, Fuel Injection Enterprise) Engle solid lifter cam Custom aluminum rods and pistons by Venolia 50 runs on this rebuild, new mains and rod bearing installed of the winter for the new
season
New parts not used: Heads, Pistons, Rods, Roller cam.
You would need a new block as I was going to build a short stroke smaller displacement motor to rev higher and
make more use of the blower.
Kauffman heads
High Port h-11 springs. (Solid roller cam) 64 CC 380 CFM port work 2.200 intake, 1.750 exhaust 1200 series Ferrea valves titanium retainers ARP High Port head stud kit 10 degree locks ARP Rocker arm studs and a girdle
Extra parts:
Moon Front Timing Chain Cover for dual drive for Mag and Pump Enderle front Offset dual drive Mallory Super III Magneto (rebuilt by Spud Miller) Engle Roller cam Solid Roller Copper struck custom grind EX4 intake / EX6 Exhaust Additional 25 gallons of fuel fresh this
summer
Transmission
Reid case PowerGlide Transmission
Built by Rutland Transmission Service, 4415 Spring Stuebner Rd., Spring, TX 77389
See the build here http://www.lever-family-racing.com/lever-family-racing-home/family-vehicles/2010-front-engine-dragster/2010-front-engine-dragster-week-2009-12-26
Trailer
Custom built
60” extended tongue, Eliminator exterior package A/C Aluminum wheels Outside lights Inside is metal lined, custom light fixtures Front storage compartment on the tongue L shaped lower cabinet with generator storage, Upper cabinets Honda generator Metal sheathing on the underside; plywood is not exposed to the elements
Yellow top battery, with built-in trickle charger
Under coated by Z-Berit Air compressor 1 ½ inch thick flooring 5 fuel jugs New brakes: drums, backing plates, shoes, electric brake on all four wheels
Weather Station Two four foot tables
E load rage tires; spare wheel and tire Two 8 X 8 Quick Shade canopies 5000 super winch 25 foot flag pole
Tow vehicle
Big Red Honda three wheeler
This is a complete racing package. Just tow it to the track and go racing.
Everything you will need to go down the track is included.
Will pass all tech inspections. All certifications are current.
Contact: [email protected]
585 704 3345