ford f150 street series 2018 installation manual · l aluminum profile 2 pcs ... profile adhesive...
TRANSCRIPT
www.airdesignusa.com
INSTALLATION MANUAL
PG. 1
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
READ CAREFULLY BEFORE INSTALLATION
We recommend 3 persons for installation
DRIVE SLOWLY25 mph max
DO NOT WASH CAR
24 hrs
AFTER INSTALLATION
ITEM DESCRIPTION DRAWING AMOUNT
A *DOUBLE SIDED TAPE INCLUDE INTHE PARTS
B BRACKETS CORD 6 PCS
C STAINLESS STEEL FLANGE NUT 8MM 12 PCS
D PUSH PIN # 501 111 46 4 PCS
E GREASE PENCIL 1 PC
F PUSH PIN # 501 967 517 2 PCS
G HEX. STAINLESS SCREW 5/16” X 1” 6 PCS
H STAINLESS STEEL WASHER 5/8” 6 PCS
I ADHESIVE POLYURETHANE 1 PC
J PUSH PIN # 501 957 387 2 PCS
K THREADLOCKER 1 PC
L ALUMINUM PROFILE 2 PCS
CHECK LIST *ALREADY PRE-INSTALLED ON THE PART
TOOLS
1/2”1/4”
THIRD MANUAL3 PART # RIGHT: 1118BNEUFO25B25
PART # LEFT: 1118ANEUFO25B26LH SIDE SKIRT STREET SERIES SUPER CREW 5 2/2
RH SIDE SKIRT STREET SERIES SUPER CREW 5 1/2
México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.
INSTALLATION MANUAL
2
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
2 CLEAN INNER CHANNEL
3 PEEL
LINER
1 CLEAN
AFTER INSTALLING FENDER FLARES
BOTTOM VIEW
www.airdesignusa.com
INSTALLATION MANUAL
PG. 3
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
APPLY POLYURETHANE
PLACEPRESS
PLACE PUSH PIN
Ø 1/4”
5
VERIFY FITTING WITH REAR FENDER FLARE
4
A)
B) C)
México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.
INSTALLATION MANUAL
4
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
7 PRESS
A full surface contact between tape and substrate is decisive for good adhesion performance. Contact is achieved by applying pressure. In practice a pressure between 40 and 50 N/cm² is usually needed and an application temperature between 25 and 45 °C or 77 and 113 °F is also necessary. During application, add-on parts and tapes must have the
similar temperature.
8 DRILL
Ø 1/4"
6 PEEL
240-50 N/cm
www.airdesignusa.com
INSTALLATION MANUAL
PG. 5
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
9 PLACE PUSH PIN
JF
REPEAT FOR RH SIDE
INSTALLED PART
México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.
INSTALLATION MANUAL
6
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
11 PLACE PROFILE
MATCH WITHRIVET NUT
RIGHT PROFILE
BOTTOM VIEW
LEFT PROFILE
BOTTOM VIEW
FRONT FRONT
2 HOLES 1 HOLE
10
B
PLACE BRACKETS
INNER VIEWBC
INNER VIEW
1/2”
BOTTOM VIEW
L
L L
www.airdesignusa.com
INSTALLATION MANUAL
PG. 7
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
SECTION VIEW
PROFILE
BRACKET
APPLY THREAD LOCKER
BOTTOM VIEW
G
H
H H H
H
G G G
G
12 SCREW
1/2”
13 CLEAN
INNER VIEW OF SIDE SKIRT
SECTION VIEW OF SIDE SKIRT
L
L
L
K
L
México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.
INSTALLATION MANUAL
8
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
LINER
14 PEEL
15 APPLY POLYURETHANE
Ø 1/4”
16 PLACE
VERIFY FITTING BETWEEN SIDE SKIRT AND FENDER FLARE
INNER VIEW OF SIDE SKIRT
UPPER FACE OF PROFILE
SECTION VIEW
BRACKET
SIDE SKIRT
PROFILE
ADHESIVE
L
www.airdesignusa.com
INSTALLATION MANUAL
PG. 9
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
18 REMOVE LINER
17
ALIGN WITHEXTENSION
ALIGN
19 PRESS
240-50 N/cm
A full surface contact between tape and substrate is decisive for good adhesion performance. Contact is achieved by applying pressure. In practice a pressure between 40 and 50 N/cm² is usually needed and an application temperature between 25 and 45 °C or 77 and 113 °F is also
necessary. During application, add-on parts and tapes must have the similar temperature.
SECTION VIEW
BRACKET
SIDE SKIRTPROFILE
ADHESIVE
L
México (+52) 55 5393 6636 / USA +1 (760) 435 0095 PG.
INSTALLATION MANUAL
10
FORD F-150 STREET SERIES 2018
DATE: 16.02.2018
21 PLACE PUSH PIN
20 DRILL
Ø 1/4"
INSTALLED PART
REPEAT RH SIDE
D D