ford kuga owner's manual - · pdf fileford kuga owner's manual. the information...
TRANSCRIPT
FORD KUGA Owner's Manual
The information contained in this publication was correct at the time of going to print. In the interest ofcontinuous development, we reserve the right to change specifications, design or equipment at any timewithout notice or obligation. No part of this publication may be reproduced, transmitted, stored in aretrieval system or translated into any language in any form by any means without our written permission.Errors and omissions excepted.© Ford Motor Company 2011
All rights reserved.Part Number: (CG3542en) 08/2011 20110725131049
IntroductionAbout This Manual...........................................7Symbols Glossary.............................................7Parts and Accessories.....................................7
At a GlanceAt a Glance........................................................10
Child SafetyChild Seats.........................................................17Child Seat Positioning...................................18Booster Seats..................................................20ISOFIX Anchor Points....................................21Child Safety Locks..........................................22
Occupant protectionPrinciple of Operation...................................23Fastening the seat belts..............................25Seat belt height adjustment......................25Seat belt reminder.........................................25Using seat belts during pregnancy..........26Disabling the passenger airbag................26
Keys and Remote ControlsGeneral Information on Radio
Frequencies..................................................28Programming the remote control............28Changing the remote control
battery............................................................28
LocksLocking and Unlocking.................................30Keyless Entry....................................................32Global Opening and Closing......................34
Engine immobiliserPrinciple of Operation..................................36Coded keys.......................................................36Arming the engine immobiliser................36Disarming the engine immobiliser...........36
AlarmArming the alarm............................................37Disarming the alarm......................................37
Steering WheelAdjusting the Steering Wheel...................39Audio Control...................................................39Voice Control...................................................40
Wipers and WashersWindscreen Wipers........................................41Autowipers........................................................41Windscreen Washers....................................42Rear Window Wiper and Washers...........42Headlamp Washers.......................................43Checking the Wiper Blades........................43Changing the Wiper Blades.......................43
LightingLighting Control..............................................45Daytime Running Lamps.............................45Autolamps........................................................46Front Fog Lamps............................................46Rear Fog Lamps.............................................46Headlamp Levelling......................................46Hazard Warning Flashers............................47Adaptive Headlamps...................................48Direction Indicators.......................................49Interior Lamps.................................................49Removing a Headlamp................................50Changing a Bulb..............................................51Bulb Specification Chart..............................57
Windows and MirrorsPower Windows.............................................59Exterior Mirrors...............................................60Electric exterior mirrors.................................61Auto-Dimming Mirror....................................61
1
Table of Contents
Instrument ClusterGauges...............................................................62Warning Lamps and Indicators.................63Audible Warnings and Indicators.............65
Information DisplaysGeneral Information......................................67Trip Computer.................................................70Personalised Settings...................................72Information Messages..................................74
Climate ControlPrinciple of Operation..................................80Air Vents............................................................80Manual Climate Control...............................81Automatic Climate Control........................83Heated Windows and Mirrors....................85Auxiliary Heater..............................................85
SeatsSitting in the Correct Position...................89Head Restraints..............................................89Manual Seats..................................................90Power Seats......................................................91Rear Seats..........................................................91Heated Seats...................................................92
Convenience featuresSun Shades......................................................93Instrument Lighting Dimmer.....................93Cup Holders......................................................93Cigar Lighter.....................................................94Auxiliary Power Points.................................94Storage compartments...............................95Glasses Holder................................................96Toll Reader.......................................................96CD changer.......................................................96Auxiliary input (AUX IN) socket................96USB port............................................................97
Satellite Navigation Unit Holder..............98Floor Mats.........................................................98
Starting and Stopping theEngine
General Information.....................................99Keyless Starting..............................................99Diesel Particulate Filter...............................101Switching Off the Engine...........................101
Fuel and RefuellingSafety Precautions......................................103Fuel Quality - Petrol....................................103Fuel Quality - Diesel....................................103Fuel filler flap.................................................103Catalytic Converter......................................105Refuelling........................................................105Fuel Consumption.......................................105Technical Specifications...........................106
TransmissionManual Transmission.................................108Automatic Transmission...........................108All-Wheel Drive...............................................111
BrakesPrinciple of Operation..................................112Hints on Driving With Anti-Lock
Brakes............................................................112Parking Brake...................................................112
Stability ControlPrinciple of Operation..................................113Using Stability Control.................................113
Parking AidsPrinciple of Operation..................................114Using the Parking Aid...................................114
2
Table of Contents
Rear view cameraPrinciple of Operation..................................116Using the Rear View Camera....................116
Cruise ControlPrinciple of Operation..................................119Using Cruise Control.....................................119
Load CarryingGeneral Information.....................................121Luggage Anchor Points................................121Luggage Covers..............................................121Rear Under Floor Storage..........................122Roof Racks and Load Carriers..................123
TowingTowing a Trailer.............................................126Tow Ball............................................................126
Driving HintsRunning-In......................................................130Cold Weather Precautions........................130Driving Through Water...............................130
Roadside EmergenciesFirst Aid Kit.......................................................131Warning Triangle............................................131
Status after a collisionFuel Cut-Off Switch.....................................132
FusesFuse Box Locations......................................133Changing a Fuse............................................133Fuse Specification Chart...........................134
Vehicle recoveryTowing Points................................................139Towing the Vehicle on Four Wheels......139
MaintenanceGeneral Information.....................................141Opening and Closing the Bonnet............141Under Bonnet Overview - 2.5L Duratec
(VI5)..............................................................143Under Bonnet Overview - 2.0L
Duratorq-TDCi (DW) Diesel.................144Engine Oil Dipstick - 2.5L Duratec
(VI5)..............................................................146Engine Oil Dipstick - 2.0L Duratorq-TDCi
(DW) Diesel................................................146Engine Oil Check...........................................146Engine Coolant Check.................................147Brake and Clutch Fluid Check..................147Power Steering Fluid Check.....................148Washer Fluid Check.....................................148Technical Specifications...........................149
Vehicle CareCleaning the Exterior....................................151Cleaning the Interior.....................................151Repairing Minor Paint Damage................152
Vehicle batteryJump-Starting the Vehicle........................153
Wheels and TyresGeneral Information....................................155Changing a Road Wheel............................155Tyre Repair Kit...............................................160Run Flat Tyres................................................163Tyre Care..........................................................165Using Winter Tyres.......................................165Using Snow Chains......................................165Tyre Pressure Monitoring System..........165Technical Specifications...........................166
Vehicle identificationVehicle Identification Plate......................169Vehicle Identification Number................169
3
Table of Contents
Capacities and Specific-ations
Technical Specifications............................170
Audio introductionImportant audio information....................173
Audio unit overviewAudio unit overview......................................174
Audio system securitySecurity code..................................................177Lost security code.........................................177Entering a security code.............................177Incorrect security code................................177
Audio unit clock and datedisplays
Setting the clock and date on the audiounit.................................................................178
Audio unit operationOn/off control................................................179Bass/treble control......................................179Balance/fade control..................................179Audio menu control.....................................179Waveband button.........................................181Station preset buttons................................181Autostore control.........................................182Traffic information control........................182Station tuning control.................................183
Audio unit menusAutomatic volume control........................185Digital signal processing (DSP)..............185Audio distortion reduction (CLIP)..........185Alternative frequencies..............................186Regional mode (REG)................................186News broadcasts..........................................187
Compact disc playerLoading compact discs..............................188Track selection..............................................188Loading the compact disc changer......188Unloading the compact disc
changer........................................................189Compact disc playback.............................189Fast forward/reverse...................................189Shuffle/random............................................189Compact disc track compression..........190Repeat compact disc tracks....................190Compact disc track scanning...................191Ejecting compact discs...............................191MP3 file playback..........................................191MP3 display options....................................192Ending compact disc playback...............192
Auxiliary input (AUX IN)socket
Auxiliary input (AUX IN) socket..............193
Audio troubleshootingAudio troubleshooting...............................194
TelephoneGeneral Information....................................195Telephone setup...........................................195Bluetooth setup............................................196Telephone controls......................................197Using the telephone - Vehicles Without:
Navigation System...................................197Using the telephone - Vehicles With:
Navigation System.................................200
Voice controlPrinciple of Operation................................202Using voice control.....................................202Audio unit commands...............................203Telephone commands................................212Navigation system commands................217
4
Table of Contents
Climate control commands......................217
ConnectivityGeneral Information...................................220Connecting an external device................221Connecting an external device - Vehicles
With: Bluetooth.........................................221Using a USB device.....................................222Using an iPod................................................224
Navigation introductionRoad Safety...................................................228
Navigation systemGetting started.............................................229
AppendicesType approvals..............................................231Type approvals..............................................231Type approvals..............................................231Electromagnetic compatibility...............232
5
Table of Contents
6
ABOUT THIS MANUALThank you for choosing Ford. Werecommend that you take some time toget to know your vehicle by reading thismanual. The more that you know about it,the greater the safety and pleasure youwill get from driving it.
WARNINGAlways drive with due care andattention when using and operatingthe controls and features on your
vehicle.
Note: This manual describes productfeatures and options available throughoutthe range, sometimes even before they aregenerally available. It may describe optionsnot fitted to your vehicle.Note: Some of the illustrations in thismanual may be used for different models,so may appear different to your vehicle.However, the essential information in theillustrations is always correct.Note: Always use and operate your vehiclein line with all applicable laws andregulations.Note: Pass on this manual when sellingyour vehicle. It is an integral part of thevehicle.This vehicle has received the endorsementof TÜV, the accredited international testingorganisation, for its allergy-friendlyproperties.All materials used in the manufacture ofthe interior of this vehicle meet strictrequirements of the TÜV TOXPROOFCriteria Catalogue for Vehicle Interiors byTÜV Produkt and Umwelt GmbH and aredesigned to minimize the risk of allergicreactions.
Additionally an efficient pollen filterprotects the passengers against allergenparticles in the outdoor air.For more information, contact TÜV atwww.tuv.com.
SYMBOLS GLOSSARYSymbols in this handbook
WARNINGYou risk death or serious injury toyourself and others if you do notfollow the instructions highlighted
by the warning symbol.
CAUTIONYou risk damaging your vehicle if youdo not follow the instructionshighlighted by the caution symbol.
Symbols on your vehicle
When you see these symbols, read andfollow the relevant instructions in thishandbook before touching or attemptingadjustment of any kind.
PARTS AND ACCESSORIESNow you can be sure that your Fordparts are Ford partsYour Ford has been built to the higheststandards using high quality Ford OriginalParts. As a result, you can enjoy driving itfor many years.
7
Introduction
Should the unexpected occur and a majorpart needs replacing, we recommend thatyou accept nothing less than Ford OriginalParts.The use of Ford Original Parts ensures thatyour vehicle is repaired to its pre-accidentcondition and maintains its maximumresidual value.Ford Original Parts match Ford's stringentsafety requirements and high standardsof fit, finish and reliability. Quite simply,they represent the best overall repair value,including parts and labour costs.Now it is easier to tell if you have reallybeen given Ford Original Parts. The Fordlogo is clearly visible on the following partsif they are Ford Original Parts. If yourvehicle has to be repaired, look for theclearly visible Ford branding and make surethat only Ford Original Parts have beenused.
Look for the Ford logo on thefollowing partsSheet metal• Bonnet• Doors• Tailgate
E98931
Bumper, radiator grille, wing and uppertailgate• Radiator grille• Front and rear bumper• Wing• Upper tailgate
8
Introduction
E98917
Exterior mirror
E98918
Glass• Rear window• Side glass• Windscreen
E89939
Lighting• Rear lamps• Rear fog lamp• Headlamp
E98920
9
Introduction
Instrument panel overviewLeft-hand drive
C DA B E F G H I J K
T S R Q P O N M LE78209
10
At a Glance
Right-hand drive
E78210
I HG J K C E D F B A
O N M L S Q R P T
Lighting control. See Lighting Control (page 45). Front fog lamps. See FrontFog Lamps (page 46). Rear fog lamp. See Rear Fog Lamps (page 46).
A
Headlamp levelling control. See Headlamp Levelling (page 46).BMulti-function lever: Information display controls. Direction indicators. SeeDirection Indicators (page 49). Main beam. See Lighting Control (page45).
C
Instrument cluster. See Gauges (page 62). See Warning Lamps andIndicators (page 63).
D
11
At a Glance
Horn.EWiper lever. See Wipers and Washers (page 41).FCard holder.GAir vents. See Air Vents (page 80).HHazard warning flasher switch. See Hazard Warning Flashers (page 47).IStart button. See Keyless Starting (page 99).JHeated windscreen switch. See Heated Windows and Mirrors (page 85).KHeated rear window switch. See Heated Windows and Mirrors (page 85).LClimate controls. See Climate Control (page 80).MAudio unit. See Audio unit overview (page 174).NNavigation unit. See separate handbook.NHeated front seat switch. See Heated Seats (page 92).OIgnition switch.PSteering wheel adjustment. See Adjusting the Steering Wheel (page 39).QCruise control switches. See Using Cruise Control (page 119).RAudio controls. See Audio Control (page 39).SInstrument lighting dimmer. See Instrument Lighting Dimmer (page 93).T
Locking and unlockingUnlocking the vehicle
E71963
ABC
UnlockALockBTailgate unlockC
Press the unlock button once to unlock thevehicle. See Programming the remotecontrol (page 28).Press and hold the unlock button for threeseconds to unlock the vehicle and openthe windows (global opening)*.Press the lock button once to activatecentral locking and arm the alarm.Press the lock button twice within threeseconds to activate double locking andarm the interior sensors.Press and hold the lock button for threeseconds to lock the vehicle and close thewindows (global closing)*.Press the tailgate unlock button twicewithin three seconds to unlock the luggagecompartment.Press and hold the tailgate unlock buttonto unlock the upper tailgate.
12
At a Glance
* only in combination with four electricwindows.
Opening the luggage compartment lid
E139497
B
A
To open the main luggage compartmentlid, press switch A. The driver’s door mustbe unlocked.To open the upper luggage compartmentlid, press switch B.
See Locking and Unlocking (page 30).
Keyless entry
E78276
Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.
Unlocking the vehicle
E78278
Pull a door handle to unlock all the doorsand the luggage compartment lid anddisarm the alarm.
13
At a Glance
Locking the vehicle
E87384
Locking buttons are located on each of thefront doors.
See Keyless Entry (page 32).
Keyless starting
E85766
Press the start button.
See Keyless Starting (page 99).
Adjusting the steering wheelWARNING
Never adjust the steering wheelwhen the vehicle is moving.
1
2
2
E95178
3E95179
WARNINGMake sure that you fully engage thelocking lever when returning it to itsoriginal position.
See Adjusting the Steering Wheel(page 39).
14
At a Glance
Manual climate controlDefrosting and demisting thewindscreen
E71382
Rapid heating of vehicle interior
E71377
See Manual Climate Control (page 81).
Automatic climate control
E78730
E D C
BA
Windscreendefrosting/demisting
A
Toggle mono mode on and offBAir conditioning OFFCRecirculated airDAir conditioning ONE
See Automatic Climate Control (page83).
Autolamps
E73840
The headlamps will come on and go offautomatically depending on the ambientlight.
See Lighting Control (page 45).
Direction indicators
E71098
If the lever is tapped up or down, thedirection indicators will flash three times.
See Direction Indicators (page 49).
15
At a Glance
Autowipers
E71014
B
Move the lever up one position.The rain sensor will continuously measurethe amount of water on the windscreenand adjust the speed of the front wipersautomatically.Adjust the sensitivity of the rain sensorusing the rotary control.
See Windscreen Wipers (page 41).
Airbag
E69213
WARNINGTo avoid the risk of death or seriousinjury, never use a rearward facingchild restraint in the front, unless the
air bag is off.
See Child Safety (page 17).See Disabling the passenger airbag(page 26).
Manual transmissionReverse gear − 6-speed transmission
E99067
See Manual Transmission (page 108).
Towing the vehicle on four wheelsCAUTION
For certain engine and transmissioncombinations, it is recommended notto tow the vehicle with the drive
wheels on the ground.
See Towing the Vehicle on FourWheels (page 139).
16
At a Glance
CHILD SEATS
E133140
E68916
WARNINGSSecure children that are less than150 centimetres (59 inches) tall in asuitable, approved child restraint, in
the rear seat.Extreme Hazard! Do not use arearward facing child restraint on aseat protected by an air bag in front
of it!Read and follow the manufacturer’sinstructions when you are fitting achild restraint.Do not modify child restraints in anyway.Do not hold a child on your lap whenthe vehicle is moving.
WARNINGSDo not leave unattended children inyour vehicle.If your vehicle has been involved inan accident, have the child restraintschecked by properly trained
technicians.
Note: Mandatory use of child restraintsvaries from country to country.Only child restraints certified toECE-R44.03 (or later) have been testedand approved for use in your vehicle. Achoice of these are available from yourDealer.
Child restraints for different massgroupsUse the correct child restraint as follows:
Baby safety seat
E68918
Secure children that weigh less than 13kilograms (29 pounds) in a rearward facingbaby safety seat (Group 0+) in the rearseat.
17
Child Safety
Child safety seat
E68920
Secure children that weigh between 13 and18 kilograms (29 and 40 pounds) in a childsafety seat (Group 1) in the rear seat.
CHILD SEAT POSITIONING
WARNINGSPlease consult your Dealer for thelatest details relating to Fordrecommended child seats.Extreme Hazard! Do not use arearward facing child restraint on aseat protected by an air bag in front
of it!
WARNINGSWhen you are using a child restraintwith a support leg on a second rowseat, make sure that you locate the
support leg securely on the under floorstorage compartment lid. Make sure thatyou install the foam spacer correctly insidethe storage compartment and that youposition the lid correctly.
When using a child seat with a seatbelt, make sure that the seat belt isnot slack or twisted.
CAUTIONThe child seat must rest tightlyagainst the vehicle seat. It may benecessary to lift or remove the head
restraint. See Head Restraints (page 89).
Note: When using a child seat on a frontseat, always adjust the front passenger seatto its fully rearwards position. If it provesdifficult to tighten the lap section of the seatbelt without slack remaining, adjust theseatback to the fully upright position andraise the height of the seat. See Seats(page 89).
Child seat positions
Mass group categories
Seating positions
3210+0
22 - 36 kg(49 - 79
lbs)
15 - 25 kg(33 - 55
lbs)
9 - 18 kg(20 - 40
lbs)Up to 13 kg
(29 lbs)Up to 10 kg
(22 lbs)
Booster seat or cushionChildsafety seatBaby safety seat
UF¹UF¹UF¹XXFront passenger seatwith airbag ON
18
Child Safety
Mass group categories
Seating positions
3210+0
22 - 36 kg(49 - 79
lbs)
15 - 25 kg(33 - 55
lbs)
9 - 18 kg(20 - 40
lbs)Up to 13 kg
(29 lbs)Up to 10 kg
(22 lbs)
Booster seat or cushionChildsafety seatBaby safety seat
U¹U¹U¹U¹U¹Front passenger seatwith airbag OFF
UUUUURear seats
X Not suitable for children in this mass group.U Suitable for universal category child seats approved for use in this mass group.U¹ Suitable for universal category child seats approved for use in this mass group. However,we recommend that you secure children in a government approved child seat, in the rearseat.UF¹ Suitable for universal category forward facing child seats approved for use in thismass group. However, we recommend that you secure children in a government approvedchild seat, in the rear seat.
ISOFIX child seats
Mass group categories
Seating positions10+
Forward facingRear facing
9 - 18 kg (20 - 40 lbs)Up to 13 kg (29 lbs)
Not ISOFIX equippedSize classFront seat
Seat type
A, B, B1, C, D1C, D, E1Size classRear outboard seat ISOFIX
IL,2 IUF3IL2Seat type
Not ISOFIX equippedSize classRear centre seat
Seat type
IL Suitable for particular ISOFIX child restraints systems of the semi-universal category.Please consult child restraints systems suppliers' vehicle recommendation lists.
19
Child Safety
IUF Suitable for ISOFIX forward facing child restraints systems of universal categoryapproved for use in this mass group and ISOFIX size class.1The ISOFIX size class for both universal and semi-universal child restraints systemsis defined by the capital letters A to G. These identification letters are displayed on ISOFIXchild restraints.2At time of publishing the recommended Group O+ ISOFIX baby safety seat is the BritaxRoemer Baby Safe. Please consult your Dealer for the latest details relating to Fordrecommended child seats.3At time of publishing the recommended Group 1 ISOFIX child seat is the Britax RoemerDuo. Please consult your Dealer for the latest details relating to Ford recommended childseats.
BOOSTER SEATS
WARNINGSDo not install a booster seat or abooster cushion with only the lapstrap of the seat belt.Do not install a booster seat or abooster cushion with a seat belt thatis slack or twisted.Do not put the seat belt under yourchild’s arm or behind its back.Do not use pillows, books or towelsto boost your child’s height.Make sure that your children sit in anupright position.Secure children that weigh morethan 15 kilograms (33 pounds) butare less than 150 centimetres (59
inches) tall in a booster seat or a boostercushion.
CAUTIONWhen using a child seat on a rear seat,make sure that the child seat reststightly against the vehicle seat. It may
be necessary to lift or remove the headrestraint. See Head Restraints (page 89).
Booster seat (Group 2)
E70710
We recommend that you use a boosterseat that combines a cushion with abackrest instead of a booster cushion only.The raised seating position will allow youto position the shoulder strap of the adultseat belt over the centre of your child’sshoulder and the lap strap tightly acrossits hips.
20
Child Safety
Booster cushion (Group 3)
E68924
ISOFIX ANCHOR POINTS
E68945
You can fit ISOFIX child restraints usingthe ISOFIX anchor points.Your vehicle is fitted with ISOFIX anchorpoints that accommodate universallyapproved ISOFIX child restraints.The ISOFIX system comprises of two rigidattachment arms on the child restraint thatattach to anchor points on the rear seats,where the cushion and backrest meet.
A third anchor point has been provided forchild seats that are equipped with a toptether, available for use in the forwardfacing configuration.The top tether anchors in your vehicle arelocated on the floor of the luggagecompartment.The tether strap should be routed beneaththe raised rear head restraint, to the anchorpoint on the floor of the luggagecompartment. The anchor point isidentified by a pictogram.After installing the child safety seat,tighten the tether strap according to themanufacturer's instructions.
WARNINGUse an anti-rotation device whenusing the ISOFIX system. Werecommend that you use a top tether
or a support leg.
Attaching a child restraint with atop tether
E78828
WARNINGDo not attach a tether strap toanything other than the correcttether anchor point.
21
Child Safety
Route the tether strap to the anchor point.Tighten the tether strap to themanufacturer's instructions.
WARNINGSMake sure the top tether strap is notslack or twisted and is properlylocated on the anchor point.Make sure that the seatback issecure and fully engaged in thecatch.
CHILD SAFETY LOCKS
WARNINGYou cannot open the doors frominside if you have put the child safetylocks on.
E112197
Left-hand sideTurn anti-clockwise to lock and clockwiseto unlock.
Right-hand sideTurn clockwise to lock and anti-clockwiseto unlock.
22
Child Safety
PRINCIPLE OF OPERATIONAirbags
WARNINGSDo not modify the front of yourvehicle in any way. This couldadversely affect deployment of the
airbags.Original text according to ECER94.01: Extreme Hazard! Do not usea rearward facing child restraint on
a seat protected by an airbag in front of it!Wear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use
the seat belt properly, can it hold you in aposition that allows the airbag to achieveits optimum effect. See Sitting in theCorrect Position (page 89).
Have repairs to the steering wheel,steering column, seats, airbags andseat belts carried out by a properly
trained technician.Keep the areas in front of the airbagsfree from obstruction. Do not affixanything to or over the airbag covers.Do not poke sharp objects into areaswhere airbags are fitted. This coulddamage and adversely affect
deployment of the airbags.Use seat covers designed for seatswith side airbags. Have these fittedby a properly trained technician.
Note: You will hear a loud bang and see acloud of harmless powdery residue if anairbag deploys. This is normal.Note: Only wipe airbag covers with a dampcloth.
Driver and front passenger airbags
E74302
The driver and front passenger airbags willdeploy during significant frontal collisionsor collisions that are up to 30 degrees fromthe left or the right. The airbags will inflatewithin a few thousandths of a second anddeflate on contact with the occupants,thus cushioning forward body movement.During minor frontal collisions, overturns,rear collisions and side collisions, the driverand front passenger airbags will notdeploy.
Side airbags
E72658
Side airbags are fitted inside the seatbackof the front seats. A label indicates thatside airbags are fitted to your vehicle.
23
Occupant protection
The side airbags will deploy duringsignificant lateral collisions. Only the airbagon the side affected by the collision willdeploy. The airbags will inflate within a fewthousandths of a second and deflate oncontact with the occupants, thus providingprotection for the chest and shoulderareas. During minor lateral collisions,overturns, front collisions and rearcollisions, the side airbags will not deploy.
Curtain airbags
E75004
Curtain airbags are fitted inside the trimpanels over the front and rear sidewindows. Moulded badges in the B-pillartrim panels indicate that curtain airbagsare fitted to your vehicle.The curtain airbags will deploy duringsignificant lateral collisions. Only the airbagon the side affected by the collision willdeploy. The airbag will inflate within a fewthousandths of a second and deflate oncontact with the occupants, thus providingprotection for the head. During minorlateral collisions, front collisions, rearcollisions, or overturns the curtain airbagswill not deploy.
Seat beltsWARNINGS
Wear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use
the seat belt properly, can it hold you in aposition to achieve its optimum effect. SeeSitting in the Correct Position (page89).
Never use a seat belt for more thanone person.Use the correct buckle for each seatbelt.Do not use a seat belt that is slackor twisted.Do not wear thick clothing. The seatbelt must fit tightly around your bodyto achieve its optimum effect.Position the shoulder strap of theseat belt over the centre of yourshoulder and position the lap strap
tightly across your hips.
The driver and front passenger seat beltbuckles are fitted with a seat beltpretensioner. Seat belt pretensioners havea lower deployment threshold than theairbags. During minor collisions, it ispossible that only the seat beltpretensioners will deploy.
Status after a collision
WARNINGSeat belts subjected to strain, as aresult of an accident, should berenewed and the anchorages
checked by a properly trained technician.
24
Occupant protection
FASTENING THE SEAT BELTS
WARNINGInsert the tongue into the buckle untilyou hear a distinct click. You havenot fastened the seat belt properly
if you do not hear a click.
E74124
E85817
Pull the belt out steadily. It may lock if youpull it sharply or if the vehicle is on a slope.Press the red button on the buckle torelease the belt. Let it retract completelyand smoothly.
SEAT BELT HEIGHTADJUSTMENT
E87511
Note: Lifting the slider slightly whilepressing the locking button makes it easierto release the locking mechanism.To raise or lower, press the locking buttonon the adjuster and move as necessary.
SEAT BELT REMINDER
WARNINGThe occupant protection system willonly provide optimum protectionwhen you use the seat belt properly.
The seat belt reminder warninglamp illuminates and an audiblewarning will sound if the driver's
or front seat passenger's seat belt has notbeen fastened and the vehicle exceeds arelatively low speed. It will also illuminateif the driver's or front seat passenger's seatbelt is unfastened when the vehicle ismoving. The audible warning will go offafter five minutes but the seat beltreminder warning lamp will remain on untilthe driver's or front seat passenger's seatbelt is fastened.
25
Occupant protection
Deactivating the seat beltreminderSee your dealer.
USING SEAT BELTS DURINGPREGNANCY
E68587
WARNINGPosition the seat belt correctly foryour safety and that of your unbornchild. Do not use only the lap strap
or the shoulder strap.
Position the lap strap comfortably acrossyour hips and low beneath your pregnantabdomen. Position the shoulder strapbetween your breasts, above and to theside of your pregnant abdomen.
DISABLING THE PASSENGERAIRBAG
WARNINGMake sure that the passenger airbagis disabled when using a rearwardfacing child restraint on the front
passenger seat.
E71313
Fitting the passenger airbagdeactivation switch
WARNINGIf you need to fit a child restraint ona seat protected by an operationalairbag in front of it, have a passenger
airbag deactivation switch fitted. Ask yourdealer for further information.
Note: The key switch is located in the glovecompartment with an airbag deactivationlamp in the instrument panel.If the airbag warning lamp illuminates orflashes when you are driving, this indicatesa malfunction. See Warning Lamps andIndicators (page 63). Remove the childrestraint and have the system checkedimmediately.
Disabling the passenger airbag
A BE71312
DisabledAEnabledB
26
Occupant protection
Turn the switch to position A.When you switch the ignition on, check thatthe passenger airbag deactivation warninglamp illuminates.
Enabling the passenger airbagWARNING
Make sure that the passenger airbagis enabled when you are not using achild restraint on the front passenger
seat.
Turn the switch to position B.
27
Occupant protection
GENERAL INFORMATION ONRADIO FREQUENCIES
CAUTIONSThe radio frequency used by yourremote control can also be used byother short distance radio
transmissions (e.g. amateur radios,medical equipment, wireless headphones,remote controls and alarm systems). If thefrequencies are jammed, you will not beable to use your remote control. You canlock and unlock the doors with the key.
Check your vehicle is locked beforeleaving it unattended. This willsafeguard against any potential
malicious frequency blocking.
Note: You could unlock the doors if youpress the buttons on the remote controlunintentionally.The operating range between your remotecontrol and your vehicle varies dependingon the environment.
PROGRAMMING THE REMOTECONTROLYou can programme a maximum of eightremote controls to use with your vehicle(including any supplied with your vehicle).Ask your dealer for instructions.
CHANGING THE REMOTECONTROL BATTERY
E107998
Make sure that you dispose ofold batteries in anenvironmentally friendly way.
Seek advice from your local authorityregarding recycling.
1
2
E78284
1. Slide the release slider in the directionof the arrow.
2. Remove the key blade.
E105064
3
3. Twist the screwdriver in the positionshown to separate the two halves ofthe remote control.
CAUTIONDo not touch the battery contacts orthe printed circuit board with thescrewdriver.
4. Carefully prise out the battery with thescrewdriver.
5. Install a new battery (3V CR 2032) withthe + facing downwards.
6. Assemble the two halves of the remotecontrol.
28
Keys and Remote Controls
7. Install the key blade.
29
Keys and Remote Controls
LOCKING AND UNLOCKINGCentral lockingYou can only centrally lock the doors if theyare all closed.Note: The driver’s door can be unlockedwith the key. This needs to be used if theremote control is not functioning.
Double lockingWARNING
Do not activate double locking whenpersons or animals are inside thevehicle. You will not be able to
unlock the doors from the inside if you havedouble locked them.
E71961
Double locking is a theft protection featurethat prevents someone from opening thedoors from the inside. You can only doublelock the doors if they are all closed.
Locking and unlockingconfirmationWhen you unlock the doors, the directionindicators will flash once.When you lock the doors, the directionindicators will flash twice.
Note: The direction indicators will flashtwice as soon as you activate centrallocking. They will not flash again when youpress the lock button on the remote controlor turn the key for the second time, i.e. whenyou activate double locking.
Locking and unlocking the doorswith the keyTurn the top of the key towards the frontof the vehicle to lock the door. Turn the topof the key towards the rear of the vehicleto unlock the door.
Double locking the doors with thekeyTurn the key to the lock position twicewithin three seconds to double lock thedoors.
Locking and unlocking the doorsand the luggage compartment lidwith the remote control
E87379
A B C
UnlockALockBLuggage compartment lid unlockC
Locking the doors and the luggagecompartment lid with the remotecontrolPress button B once.
30
Locks
Double locking the doors and theluggage compartment lid with theremote controlPress button B twice within three seconds.
Locking and unlocking the doorsfrom insideDriver's door
A
B
E99606
Lock all doorsAUnlock all doorsB
Front and rear passenger doors
E99607
To lock the front and rear passenger doorsindividually, press the button and close thedoor when leaving the vehicle.
Luggage compartment lidOpening the luggage compartment lid
E139497
B
A
Main luggage compartment lidAUpper luggage compartment lidB
Opening the main luggagecompartment lid with the remotecontrolPress button C on the remote control twicewithin three seconds.
31
Locks
Opening the upper luggagecompartment lid with the remotecontrolPress and hold button C on the remotecontrol.
Closing the luggage compartment lidUpper luggage compartment lid
E99410
Main luggage compartment lid
E99470
Automatic relockingThe doors will relock automatically if youdo not open a door within 45 seconds ofunlocking the doors with the remotecontrol. The door locks and the alarm willreturn to their previous state.
Reprogramming the unlockingfunctionNote: When you press the unlock buttoneither all the doors are unlocked or only thedriver’s door and the luggage compartmentlid are unlocked. Pressing the unlock buttonagain unlocks all the doors.Press and hold the unlock and lock buttonson the remote key simultaneously for atleast four seconds with the ignition off. Thedirection indicators will flash twice toconfirm the change. See Programmingthe remote control (page 28).To return to the original unlocking function,repeat the process.
KEYLESS ENTRYGeneral information
WARNINGThe keyless entry system may notfunction if the key is close to metalobjects or electronic devices such as
mobile phones.
Note: If the door handles are pulledrepeatedly during a short period of timewithout the presence of a valid passive key,the system will become inoperable for 30seconds.The passive entry system will not functionif:• The passive key frequencies are
jammed.• The passive key battery is flat.Note: If the passive entry system does notfunction, you will need to use the key bladeto lock and unlock your vehicle.The keyless system allows the driver tooperate the vehicle without the use of akey or remote control.
32
Locks
E78276
Passive locking and unlocking requires avalid passive key to be located within oneof the three external detection ranges.These are located approximately one anda half metres from the driver and frontpassenger door handles and the luggagecompartment lid.
Passive keyThe vehicle can be locked and unlockedwith the passive key. The passive key canalso be used as a remote control. SeeLocking and Unlocking (page 30).
Locking the vehicle
E87384
WARNINGThe vehicle does not lock itselfautomatically. If no locking button ispressed, the vehicle will remain
unlocked.
Locking buttons are located on each of thefront doors.To activate central locking and arm thealarm:• Press a locking button once.To activate double locking, to arm thealarm and the interior sensors:• Press a locking button twice within
three seconds.Note: Once activated, the vehicle willremain locked for approximately threeseconds. This is to allow you to pull a doorhandle and check if the vehicle is locked.When the delay period is over, the doors canbe opened again, provided the passive keyis within the respective detection range.
Luggage compartment lidNote: The luggage compartment lid cannotbe closed and will pop back up if the passivekey is located inside the luggagecompartment.Note: If a second valid passive key islocated within the luggage compartmentlid detection range, the luggagecompartment lid can be closed.
Unlocking the vehicleNote: If the vehicle remains locked forlonger than three days, the key free systemwill enter an energy-saving mode. This is toreduce the discharge of the vehicle battery.When the vehicle is unlocked while in thismode, the reaction time of the system maybe a little longer than normal. Unlocking thevehicle once will deactivate theenergy-saving mode.
33
Locks
E78278
Pull one of the door handles or the luggagecompartment lid handle.Note: A valid passive key must be locatedwithin the detection range of that door.One long flash of the direction indicatorsconfirms that all the doors, the luggagecompartment lid and the fuel filler flaphave been unlocked and that the alarmhas been disarmed.
Unlocking only the driver's doorIf the unlocking function is reprogrammedso that only the driver’s door is unlocked (See Programming the remote control(page 28). ), note the following:If the driver’s door is the first door which isopened, the other doors and the luggagecompartment lid will remain locked. All theother doors can be unlocked from insidethe vehicle by using the unlock button nextto the driver’s door handle. Doors can beunlocked individually by pulling the interiordoor handles on those doors.If the front passenger door or one of therear doors is the first door which is opened,all the doors and the luggagecompartment lid will be unlocked.
Disabled keysAny keys left inside the vehicle interiorwhen it is locked will be disabled.A disabled key cannot be used to turn theignition on or start the engine.In order to use these passive keys again,they have to be enabled.To enable all your passive keys, unlock thevehicle using a passive key or the remotecontrol unlocking function.All passive keys will then be enabled if theignition is turned on or the vehicle is startedusing a valid key.
Locking and unlocking the doorswith the key blade
1
2
E78284
1. Slide the release slider in the directionof the arrow and pull out the key bladewith your thumb.
2. Remove the key blade and insert it intothe lock.
GLOBAL OPENING ANDCLOSINGYou can also operate the electric windowswith the ignition off via the global openingand global closing function.
34
Locks
Note: Global closing will only operate if youhave set the memory correctly for eachwindow. See Power Windows (page 59).
Global opening
E71955
To open all the windows, press and holdthe unlock button for at least threeseconds. Press either the lock or theunlock button again to stop the openingfunction.
Global closingWARNING
Take care when using global closing.In an emergency, press the buttonon the driver’s door handle to stop.
Note: Global closing can be activated usingthe button on the driver’s door handle.Global opening and closing can also beactivated using the buttons on the passivekey.
E99679
E87384
To close all the windows, press and holdthe button on the driver’s door handle forat least two seconds. The anti-trapfunction is also active during global closing.
35
Locks
PRINCIPLE OF OPERATIONThe engine immobiliser is a theft protectionsystem that prevents someone fromstarting the engine with an incorrectlycoded key.
CODED KEYSNote: Do not shield your keys with metalobjects. This may prevent the receiver fromrecognising your key as a valid one.Note: Have all of your remaining keyserased and recoded if you lose a key. Askyour dealer for further information. Havereplacement keys recoded together withyour existing keys.If you lose a key, you can obtain areplacement from your Ford Dealer. Ifpossible, provide them with the keynumber from the tag provided with theoriginal keys. You can also obtainadditional keys from your Ford Dealer.
ARMING THE ENGINEIMMOBILISERThe engine immobiliser is armedautomatically a short time after you haveswitched the ignition off.
DISARMING THE ENGINEIMMOBILISERThe engine immobiliser is disarmedautomatically when you switch the ignitionon with a correctly coded key.The indicator in the instrument cluster willcome on for approximately three secondsand then go out. If the indicator stays onfor one minute or flashes for approximatelyone minute and then repeatedly at irregularintervals, your key has not been recognised.Remove the key and try again.
If you are unable to start the engine with acorrectly coded key, this indicates amalfunction. Have the immobiliser checkedimmediately.
36
Engine immobiliser
ARMING THE ALARMThe system is armed as soon as the vehicleis locked and acts as a deterrent tounauthorised persons who attempt toopen the doors, bonnet or luggagecompartment, or remove the audio system.The alarm sounds for 30 seconds if anunauthorised person opens a door, theluggage compartment or the bonnet. Thehazard flasher lights will flash for fiveminutes.Any attempt to start the engine without avalid key or to remove the audio systemsounds the alarm again.
Automatic arming delayThe 20 seconds arming delay begins whenthe bonnet, luggage compartment and alldoors are closed.
Interior sensors
E71401
WARNINGThis system functions correctly onlyif all windows are completely closed.In addition to this, the sensors
located in the interior lamp unit must notbe covered up. The system should not beactivated if any persons, animals or othermoving objects are inside the vehicle.
This system acts as a deterrent againstunauthorised intrusion by sensing anymovement within the vehicle.
Unauthorised entry into the vehicle’sinterior will trigger the alarm in the sameway as the anti-theft system.The sensors are located in the interior lampunit.
All except Britain and IrelandThe interior sensing alarm is armedtogether with the double locking system.
Britain and Ireland onlyThe interior sensing alarm is armedtogether with the central locking system.To deactivate the interior sensors pressthe switch next to the driver’s door handle.
DISARMING THE ALARMThe system can be deactivated at anytime, even when the alarm is sounding, byunlocking the vehicle from the outside.The system will be deactivated if:• A valid passive key is located within the
detection range.• The unlock button on the remote
control is pressed.• A valid passive key is located within the
vehicle interior and you depress theclutch pedal (manual transmission) orbrake pedal (automatic transmission).
• You insert the key blade into the keyholder.
The system for the luggage compartmentlid will be deactivated if.• A valid passive key is located within the
detection range.• The luggage compartment lid unlock
button on the remote control ispressed.
37
Alarm
Britain and Ireland onlyIf the vehicle is unlocked using the keyblade, a 12 second delay chime starts assoon as the driver’s door is opened. Thealarm will be deactivated during thisperiod.
38
Alarm
ADJUSTING THE STEERINGWHEEL
WARNINGNever adjust the steering wheelwhen the vehicle is moving.
Note: Make sure that you are sitting in thecorrect position. See Sitting in the CorrectPosition (page 89).
1
2
2
E95178
3E95179
WARNINGMake sure that you fully engage thelocking lever when returning it to itsoriginal position.
AUDIO CONTROLSelect radio, CD or cassette mode on theaudio unit.The following functions can be operatedwith the remote control:
Volume
E78046
Volume up: Press the top button on theback of the remote control.Volume down: Press the bottom buttonon the back of the remote control.
39
Steering Wheel
Seek
E78047
Move the lever up or down:• In radio mode, this will locate the next
radio station up or down the frequencyband.
• In CD mode, it will select the next orprevious track.
Mode
E78048
Briefly press the button on the side:
• In radio mode, this will locate the nextpre-set radio station.
• In CD mode, this will select the nextCD if a CD changer is fitted.
• In all modes to abort a traffic messageduring broadcasting.
Press and hold the button on the side:• In radio mode to change the
waveband.
VOICE CONTROL
E78049
To select or deselect voice control, pressthe button on the top.For further information See Voice control(page 202).
40
Steering Wheel
WINDSCREEN WIPERS
E71012
A
B
C
D
Single wipeAIntermittent wipe or autowipersBNormal wipeCHigh speed wipeD
Intermittent wipe
E71013
C
A B
Long wipe intervalAIntermittent wipeBShort wipe intervalC
Automatic wiper systemSome models without autowipers arefitted with a speed-dependent front screenwiper system.When the vehicle is slowed to walkingspeed or is brought to a standstill, thewiper speed will automatically switch tothe next lower wiper speed setting.When the vehicle speed is increased, thewiper speed will return to themanually-chosen setting.Moving the wiper lever when the system isoperating will switch off the system.If the vehicle is again slowed to walkingspeed or is brought to a standstill, thesystem is reactivated.
AUTOWIPERS
CAUTIONSDo not switch autowipers on in dryweather conditions. The rain sensoris very sensitive and the wipers may
operate if dirt, mist or flies hit thewindscreen.
Replace the wiper blades as soon asthey begin to leave bands of waterand smears. If you do not replace
them, the rain sensor will continue todetect water on the windscreen and thewipers will operate, even though themajority of the windscreen is dry.
Fully defrost the windscreen in icyconditions before you switchautowipers on.Switch autowipers off before youenter a car wash.
41
Wipers and Washers
E71013
C
A B
Low sensitivityAOnBHigh sensitivityC
If you switch autowipers on, the wipers willnot cycle until water is detected on thewindscreen. The rain sensor will thencontinuously measure the amount of wateron the windscreen and adjust the speedof the wipers automatically.Adjust the sensitivity of the rain sensorusing the rotary control. With lowsensitivity, the wipers will operate whenthe sensor detects a lot of water on thewindscreen. With high sensitivity, thewipers will operate if the sensor detects asmall amount of water on the windscreen.
WINDSCREEN WASHERS
E71016
WARNINGDo not operate the washer for morethan 10 seconds at a time, and neverwhen the reservoir is empty.
While the button at the end of the lever ispressed the washer will work inconjunction with the wipers.After releasing the button, the wipersoperate for a short time.
REAR WINDOW WIPER ANDWASHERSIntermittent wipe
E71017
Pull the lever towards the steering wheel.
Reverse gear wipeThe rear wiper will be activatedautomatically when selecting reverse gearif:• the rear wiper is not already switched
on,• the wiper lever is in position A, B, C or
D and• the front wiper is operating (when set
to position B).The rear wiper will follow the front wiperinterval (at intermittent or normal speed).
42
Wipers and Washers
Rear window washer
E71018
WARNINGDo not operate the washer for morethan 10 seconds at a time, and neverwhen the reservoir is empty.
While the lever is pulled towards thesteering wheel the washer will work inconjunction with the wipers.Once the wash and wipe cycle iscompleted, the wipers will pause and thenperform one more wipe to clear thewindscreen.After releasing the lever, the wipersoperate for a short time.
HEADLAMP WASHERSThe headlamp washers will operate withthe windscreen washers when theheadlamps are on.Note: To stop the washer fluid reservoiremptying quickly, the headlamp washerswill not operate every time that you use thewindscreen washers.
CHECKING THE WIPERBLADES
E66644
Run the tip of your fingers over the edge ofthe blade to check for roughness.Clean the wiper blade lips with waterapplied with a soft sponge.
CHANGING THE WIPERBLADESWindscreen wiper blades
CAUTIONSSet the windscreen wipers in theservice position to change the wiperblades.You can use the service position inwinter to provide easier access to thewiper blades for freeing them from
snow and ice. The windscreen wipers willreturn to their normal position as soon asyou switch on the ignition so make surethat the outside of the windscreen is freefrom snow and ice before you switch onthe ignition.
43
Wipers and Washers
Service position
E85833
E99280
A
1. Turn on the ignition.2. Move the wiper lever to position A and
turn the ignition off as soon as thewiper blades have reached the serviceposition.
Changing the windscreen wiper bladesSet the windscreen wipers in the serviceposition and lift the wiper arms.
E728991
2
1. Press the locking button.2. Remove the wiper blade.Note: Make sure that the wiper blade locksinto place.3. Install in the reverse order.
Rear window wiper blade1. Lift the wiper arm.
2
3
4
E86456
2. Position the wiper blade at right anglesto the wiper arm.
3. Disengage the wiper blade from thewiper arm.
4. Remove the wiper blade.Note: Make sure that the wiper blade locksinto place.5. Install in the reverse order.
44
Wipers and Washers
LIGHTING CONTROLLighting control positions
E71094 D
B CAF
E
OffASide and tail lampsBHeadlampsCFront fog lampsDRear fog lampsEParking lampsF
Parking lampsCAUTION
Prolonged use of the parking lampswill discharge the battery.
Switch off the ignition.Push the lighting control inwards and turnit to position F.
Main and dipped beam
E71095
Pull the lever fully towards the steeringwheel to switch between main and dippedbeam.
Headlamp flasherPull the lever slightly towards the steeringwheel.
Home safe lightingSwitch the ignition off and pull thedirection indicator lever towards thesteering wheel to switch the headlampson. You will hear a short tone. Theheadlamps will go off automatically after3 minutes with any door open, or 30seconds after the last door has beenclosed.With all doors closed, but within the 30second delay, opening any door will resultin the 3 minute timer starting again.The home safe lights can be cancelled byeither pulling the direction indicator levertowards the steering wheel again or byturning the ignition switch ON.
DAYTIME RUNNING LAMPSThe lamps will illuminate when the ignitionis on.
45
Lighting
AUTOLAMPS
WARNINGIn severe weather conditions, it maybe necessary to switch yourheadlamps on manually.
Note: If you have switched autolamps on,you can only switch the main beam on whenautolamps has switched the headlamps on.
E73840
The headlamps will come on and go offautomatically depending on the ambientlight.
FRONT FOG LAMPS
E71096
WARNINGOnly use the front fog lamps whenvisibility is considerably restricted byfog, snow or rain.
Note: You cannot switch the front foglamps on if you have switched autolampson.
REAR FOG LAMPS
E71097
WARNINGDo not use the rear fog lamps whenit is raining or snowing and visibilityis more than 50 metres.
Note: You cannot switch the rear fog lampson if you have switched autolamps on.
HEADLAMP LEVELLINGNote: Vehicles with Xenon headlamps areequipped with automatic headlamplevelling.
46
Lighting
E65990
You can adjust the level of the headlampbeams according to the vehicle load.
Recommended headlamp levelling control positions
Control positionLoad in luggagecompartment1
Load
Rear seatsFront seats
0--1-2
1-31-2
1.5Max31-2
3Max-11 See Vehicle Identification Plate (page 169).
HAZARD WARNING FLASHERSNote: Depending on applicable laws andregulations in the country for which yourvehicle was originally built, the hazardwarning flashers may flash if you brakeheavily.
E71943
For item location: See At a Glance (page10).
47
Lighting
ADAPTIVE HEADLAMPS
E72897
A
B
A
B
without AFSAwith AFSB
The AFS adjusts the headlamp dippedbeam depending on vehicle direction andspeed. It improves visibility when you aredriving at night and helps to reduceheadlamp glare for oncoming drivers.The headlamps will also move when thevehicle is stationary and the steering wheelis turned. To prevent headlamp glare forthe oncoming traffic, they will only movetowards the passenger side of the vehicle.The system will not operate when you haveswitched on the daytime running lamps orwhen you have selected reverse gear.To activate the AFS when the daytimerunning lamps are activated, turn thelighting control to position C. See LightingControl (page 45).
A message will appear in the informationdisplay and the headlamp indicator flashesif the system malfunctions. SeeInformation Messages (page 74). Theheadlamps will move to a fixed central ordipped position. Have the system checkedas soon as possible.
48
Lighting
DIRECTION INDICATORS
E71098
Note: Tap the lever up or down to make thedirection indicators flash only three times.
INTERIOR LAMPSCourtesy lamp
CBA
E71945
OffADoor contactBOnC
If you set the switch to position B, thecourtesy lamp will come on when youunlock or open a door or the luggagecompartment lid. If you leave a door openwith the ignition switch off, the courtesylamp will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch it back on, switchon the ignition for a short time.The courtesy lamp will also come on whenyou switch off the ignition. It will go offautomatically after a short time or whenyou start or restart the engine.If you set the switch to position C with theignition switch off, the courtesy lamp willcome on. It will go off automatically aftera short time to prevent the vehicle batteryfrom discharging. To switch it back on,switch on the ignition for a short time.
Reading lamps
E71946
If you switch off the ignition, the readinglamps will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch them back on,switch on the ignition for a short time.
49
Lighting
Vanity mirror lamps
A
B
E72900
OffAOnB
If you switch off the ignition, the vanitymirror lamps will go off automatically aftera short time to prevent the vehicle batteryfrom discharging. To switch them back on,switch on the ignition for a short time.
REMOVING A HEADLAMP
WARNINGHave Xenon bulbs changed by atrained technician. There is a risk ofelectric shock.
1. Open the bonnet. See Opening andClosing the Bonnet (page 141).
2
3
E99388
2. Remove the screw.3. Using a suitable implement, remove
the trim panel.
4
E99389
4. Release the retaining clips.
50
Lighting
5
6
7
E99390
5. Disconnect the electrical connector.6. Disconnect the headlamp washer hose.7. Remove the headlamp.Note: When fitting the headlamp, makesure that you fully engage the headlamp inthe retaining clips.
CHANGING A BULB
WARNINGSSwitch the lights and the ignition off.
Let the bulb cool down beforeremoving it.Have Xenon bulbs changed by atrained technician. There is a risk ofelectric shock.
CAUTIONSDo not touch the glass of the bulb.
Only fit bulbs of the correctspecification. See BulbSpecification Chart (page 57).
HeadlampDirection indicator1. Remove the headlamp. See
Removing a Headlamp (page 50).
E99482
3
2
2. Turn the bulb holder anti-clockwiseand remove it.
3. Gently press the bulb into the bulbholder, turn it anti-clockwise andremove it.
Headlamp main and dipped beamNote: Remove the covers to gain access tothe bulbs.1. Remove the headlamp. See
Removing a Headlamp (page 50).
3
2
E72260
51
Lighting
2. Turn the bulb holder anti-clockwiseand remove it.
3. Remove the bulb.
Side lamp1. Remove the headlamp. See
Removing a Headlamp (page 50).
E99437
2 3
2. Remove the cover.3. Pull the bulb holder and remove it.
Remove the bulb.
Daytime running lampsNote: These are not serviceable items,please consult your dealer if they fail.
E139892
Side repeaters
1
E99397
1. Remove the cover.
2
3
E99398
2. Release the retaining clip.3. Remove the bulb and bulb holder.
Remove the bulb.
52
Lighting
Approach lamp
1
E72264
Note: Position the mirror glass as farinwards as possible.1. Insert a screwdriver into the gap
between the mirror housing and themirror glass and release the metalretaining clip.
E72265
2
3
2. Remove the lamp.3. Remove the bulb.
Front fog lamps
12
3
E99405
Note: You cannot separate the fog lampbulb from the bulb holder.1. Using a suitable implement, remove
the cover.2. Remove the screws.3. Remove the lamp.
4
E99406
5
4. Disconnect the electrical connector.
53
Lighting
5. Turn the bulb holder anti-clockwiseand remove it.
Rear fog lamps
31
2
E107752
1. Carefully remove the lamp.2. Turn the bulb holder anti-clockwise
and remove it.3. Remove the bulb.
Rear lampsDirection indicator and reverse lamp
1
E99407
1. Remove the trim panel.
A B
E99408
Direction indicatorAReverse lampB
2. Disconnect the electrical connector.3. Turn the bulb holder anti-clockwise andremove it.4. Remove the bulb.
Tail lamp and brake lamp
3
E99411
1. Remove the trim panel.
54
Lighting
2
E99412
2. Remove the nut.
E99413
3. Gently press the bulb into the bulbholder, turn it anti-clockwise andremove it.
Central high mounted brake lampNote: The LED board is not a serviceableitem, please consult your dealer if this fails.
Number plate lamp
3
2
1
E72789
1. Carefully release the spring clip.2. Remove the lamp.3. Remove the bulb.
Interior lampVehicles without interior sensors
E99452
2
3
1
1. Carefully prise out the lamp.2. Turn the bulb holder anti-clockwise
and remove it.3. Remove the bulb.
55
Lighting
Vehicles with interior sensors
2
3
E72787
1. Carefully prise out the lens.2. Remove the lens.3. Remove the bulb.
Reading lampsVehicles without interior sensors
E99453
2
3
1
1. Carefully prise out the lamp.2. Turn the bulb holder anti-clockwise
and remove it.3. Remove the bulb.
Vehicles with interior sensors
22
1
E72786
1. Carefully prise out the lamp.2. Turn the bulb holder anti-clockwise
and remove it.
E739393
3. Remove the bulb.
Vanity mirror lamp
E72785
56
Lighting
1. Carefully prise out the lamp.2. Remove the bulb.
Luggage compartment lamp
E99429
1 2
1. Carefully prise out the lamp.2. Remove the bulb.
BULB SPECIFICATION CHART
Power (watt)SpecificationLamp
21H21WFront direction indicator
55H7Headlamp main beam
55H7Headlamp dipped beam
5W5WSide repeater
35H8Front fog lamp
5W5WSide lamp
19PSY19WRear direction indicator
21/5W21/5WBrake and tail lamp
21P21WRear fog lamp
21P21WReversing lamp
1.41 x LED boardCentral high mounted brake lamp
5W5WNumber plate lamp
6W6WInterior lamp
57
Lighting
Power (watt)SpecificationLamp
5W5WReading lamp
5W5WVanity mirror lamp
10FestoonLuggage compartment lamp
58
Lighting
POWER WINDOWS
WARNINGDo not operate the electric windowsunless they are free from obstruction.
Note: If you operate the switches oftenduring a short period of time, the systemmight become inoperable for a certain timeto prevent damage due to overheating.Switch on the ignition to operate theelectric windows.
Global opening and closingYou can also operate the electric windowswith the ignition off via the global openingand closing function. See Locks (page30).
Driver's door switchesYou can operate all the windows with theswitches on the door trim panel of thedriver’s door.
E70848
Opening and closing the windowsautomaticallyPress or lift the switch to the second actionpoint and release it completely. Press orlift it again to stop the windows.
Safety switch for rear windowsNote: You can always operate the rearwindows from the driver’s door.
E70850
A switch in the driver’s door disables therear electric window switches.The light in the switch comes on and thelights in the rear window switches go offwhen the rear windows are disabled.
Anti-trap functionWARNING
Careless closing of the windows canoverride the protection function andcause injuries.
The electric windows will stopautomatically while closing and reversesome distance if there is an obstacle in theway.
59
Windows and Mirrors
Overriding the anti-trap function
CAUTIONWhile you close the window for thethird time, the anti-trap function isdisabled. Make sure there are no
obstacles in the way of the closing window.
To override this protection function whenthere is a resistance, e.g. in the winter,proceed as follows:1. Close the window twice until it reaches
the resistance and let it reverse.2. Close the window a third time to the
resistance. The anti-trap function isdisabled and you cannot close thewindow automatically. The windowwill override the resistance and you canclose it fully.
3. If the window does not close after thethird attempt, have it checked by anexpert.
Resetting the memory of theelectric windows
WARNINGThe anti-trap function is deactivateduntil you have reset the memory.
After the battery has been disconnectedfrom the vehicle you must reset thememory separately for each window:1. Lift and hold the switch until the
window is fully closed.2. Release the switch.3. Lift the switch again for one more
second.4. Push and hold the switch until the
window is fully open.5. Release the switch.6. Lift and hold the switch until the
window is fully closed.
7. Open the window and try to close itautomatically.
8. Reset and repeat procedure if thewindow does not close automatically.
EXTERIOR MIRRORS
WARNINGDo not overestimate the distance ofthe objects that you see in theconvex mirror. Objects seen in
convex mirrors will appear smaller andfurther away than they actually are.
Manual folding mirrorsFoldingPush the mirror towards the door windowglass.
UnfoldingMake sure that you fully engage the mirrorin its support when returning it to itsoriginal position.
60
Windows and Mirrors
ELECTRIC EXTERIORMIRRORS
A CB
E70846
Left-hand mirrorAOffBRight-hand mirrorC
Mirror tilting positions
E70847
The electric exterior mirrors are fitted witha heating element that will defrost ordemist the mirror glass. See HeatedWindows and Mirrors (page 85).
Electric folding mirrorsNote: When the mirrors are operated oftenduring a short period of time, the systemmay become inoperable for a period of timeto prevent damage due to overheating.Note: The switch must be in position B.The electric folding mirrors operate withthe ignition on.
E122706
Press the button to fold or unfold themirrors.If you press the switch again while themirrors are moving, they will stop andreverse the direction of movement.
AUTO-DIMMING MIRROR
E71028
The auto-dimming mirror will adjustautomatically when hit by glaring lightfrom behind. It will not work when you haveselected reverse gear.
61
Windows and Mirrors
GAUGES
E98738
A B C
E
D
TachometerAEngine coolant temperature gaugeBFuel gaugeCSpeedometerDInformation displayE
Engine coolant temperature gaugeAll vehiclesShows the temperature of the enginecoolant. At normal operating temperature,the needle will remain in the centre section.
CAUTIONDo not restart the engine until thecause of overheating has beenresolved.
62
Instrument Cluster
If the needle enters the red section, theengine is overheating. Stop the engine,switch the ignition off and determine thecause once the engine has cooled down.See Engine Coolant Check (page 147).
Fuel gaugeThe arrow adjacent to the fuel pumpsymbol indicates on which side of thevehicle the fuel filler cap is located.
WARNING LAMPS ANDINDICATORSThe following warning lamps andindicators illuminate when the ignition isswitched on:• Airbag• Oil pressure• ABS• Stability control (ESP)• Engine• Doors open• Brake system• Frost• Power steering• IgnitionIf a warning or indicator lamp does notilluminate when the ignition is switchedon, it indicates a malfunction. Have thesystem checked by properly trainedtechnician.
ABS warning lampIf it illuminates when you aredriving, this indicates amalfunction. You will continue
to have normal braking (without ABS).Have the system checked by a properlytrained technician as soon as possible.
Airbag warning lampIf it illuminates when you aredriving, this indicates amalfunction. Have the system
checked by a properly trained technician.
Brake system lampIt illuminates when the parkingbrake is engaged.
WARNINGReduce your speed gradually andstop your vehicle as soon as it is safeto do so. Use your brakes with care.
If it illuminates when you are driving, checkthat the parking brake is not engaged. Ifthe parking brake is not engaged, thisindicates a malfunction. Have the systemchecked by a properly trained technicianimmediately.
Cruise control indicator
E71340
It will illuminate when you haveset a speed using the cruisecontrol system. See Using
Cruise Control (page 119).
Direction indicatorsFlashes during operation. Asudden increase in the rate offlashing warns of a failed
indicator bulb. See Changing a Bulb(page 51).
Doors open warning lampIlluminates when the ignition isswitched on and remains on ifany door, the bonnet or the
luggage compartment is not closedproperly.
63
Instrument Cluster
Engine warning lampIf it illuminates with the enginerunning, this indicates amalfunction. If it flashes when
you are driving, reduce the speed of yourvehicle immediately. If it continues toflash, avoid heavy acceleration ordeceleration. Have the system checked bya properly trained technician immediately.
CAUTIONIf the engine warning lamp illuminatesin conjunction with a message, havethe system checked as soon as
possible.
Front fog lamp indicatorIt will illuminate when you switchthe front fog lamps on.
Frost warning lampWARNING
Even if the temperature rises toabove +4ºC there is no guaranteethat the road is free of hazards
caused by inclement weather.
It will illuminate and glow orangewhen the outside airtemperature is between 4ºC
(39ºF) and 1ºC (34ºF). It will glow redwhen the temperature is below 1ºC (34ºF).
Glow plug indicatorSee (page 99).
Headlamp indicatorIt will illuminate when you switchthe headlamp dipped beam orthe side and tail lamps on.
Ignition warning lampIf it illuminates when you aredriving, this indicates amalfunction. Switch off all
unnecessary electrical equipment. Havethe system checked by a properly trainedtechnician immediately.
Low fuel level warning lampIf it illuminates, refuel as soon aspossible.
Main beam indicatorIt will illuminate when you switchthe headlamp main beam on. Itwill flash when you use the
headlamp flasher.
Message indicatorIt will illuminate when a newmessage is stored in theinformation display. See
Information Messages (page 74).
Oil pressure warning lampCAUTION
Do not resume your journey if itilluminates despite the level beingcorrect. Have the system checked by
a properly trained technician immediately.
If it stays on after starting orilluminates when driving, thisindicates a malfunction. Stop
your vehicle as soon as it is safe to do soand switch the engine off. Check the engineoil level. See Engine Oil Check (page 146).
64
Instrument Cluster
Power steering warning lampIt illuminates to indicate amalfunction of the powersteering system. Full steering will
be maintained but you will need to exertgreater force on the steering wheel. Havethe system checked by a properly trainedtechnician as soon as possible.
Rear fog lamp indicatorIt will illuminate when you switchthe rear fog lamps on.
Seat belt reminderSee Seat belt reminder (page25).
Shift indicatorIt will illuminate to inform youthat shifting to a higher gear maygive better fuel economy and
lower CO2 emissions. It will not illuminateduring periods of high acceleration, brakingor when the clutch pedal is pressed.
Stability control (ESP) indicatorWhile driving, it flashes duringactivation of the system. Afterswitching on the ignition, if it
does not illuminate or illuminatescontinuously while driving, this indicates amalfunction. During a malfunction, thesystem switches off. Have the systemchecked by a properly trained technicianas soon as possible.
If you switch ESP off, the warning lamp willilluminate. The lamp will go out when youswitch the system back on or when youswitch the ignition off.
AUDIBLE WARNINGS ANDINDICATORSAutomatic transmissionIf position P is not selected, a warningchime will sound when the driver’s door isopened.
FrostWARNING
Even if the temperature rises toabove +4ºC there is no guaranteethat the road is free of hazards
caused by inclement weather.
A warning chime will sound in the followingconditions:• +4ºC or lower: frost warning• 0ºC or lower: danger of icy roads.
Key outside carVehicles with keyless entryIf the engine is running and a passive keyis no longer detected within the vehicleinterior, a chime will sound as soon as thedoor is closed.
Key-in-ignitionExcept vehicles with keyless entryA warning tone will sound when the driver’sdoor is opened if:• the key is in the ignition.
Vehicles with keyless entryA warning tone will sound when the driver’sdoor is opened if:• the ignition is still on• the spare key is in the ignition.
65
Instrument Cluster
Lights onA warning chime will sound if the driver’sdoor is opened with the exterior lightsswitched on and the ignition switched off.
Low fuelA warning chime will sound at thefollowing ranges: 80 km (50 miles), 40 km(25 miles), 20 km (12 miles), 0 km (0miles).
Seat belt reminderSee Seat belt reminder (page 25).
66
Instrument Cluster
GENERAL INFORMATION
WARNINGDo not operate the informationdisplay controls when the vehicle ismoving.
Note: The information display will remainon for several minutes after you switch offthe ignition.Various systems on your vehicle can becontrolled using the multi-function leveron the steering column. Correspondinginformation is displayed in the informationdisplay.For detailed instructions on navigation,refer to the appropriate manual.
Controls
E73265
Use the rotary control:
• to scroll through the trip computerdisplays
• to scroll through and highlight theoptions within a menu.
Note: To scroll automatically, hold therotary control in the upward or downwardposition.
E73266
Press the SET/RESET button to:• enter the main menu from the trip
computer displays• enter a sub-menu• exit a menu• choose and confirm a setting.Note: If the chimes are activated, a shorttone will sound each time the button ispressed.
67
Information Displays
Menu structure
Trip OdoAvg FuelAvg SpeedAll
Set Clock24 Hour Mode
A B C
E98875
StandardSportComfort
Always offHelp Screen
DisplayConfigure
NAV InfoOn GuidanceAlways on
Reset Trip
Messages
Steering
ESP
Clock
Setup
68
Information Displays
B C
E98876
EnglishLanguage
Measure Unit
DeutschItalianoFrançaisEspañolTürkçePyccкийNederlandsPolskiSvenskaPortuguêsMetricImperial
Chimes
Aux. Heater
Low FuelGeneral WarnGeneral Info
69
Information Displays
A
E98884
Time 1 on
Set onceActive now
Set Time 1MondayTuesdayWednesdayThursdayFridaySaturdaySunday
Time 2 onSet Time 1MondayTuesdayWednesdayThursdayFridaySaturdaySunday
Park Heater
TRIP COMPUTERType 2 and 3
E74428
6.3Average Fuel
10:20
234.2 km
123456 km
l100km
A
B
C
A: Trip computerB: OdometerC: TripmeterThe trip computer includes the followinginformation displays:
OdometerRegisters the total mileage of the vehicle.
TripmeterRegisters the mileage of individualjourneys.
Distance to emptyIndicates the approximate distance thevehicle will travel on the fuel remaining inthe tank. Changes in driving pattern maycause the value to vary.
Instantaneous fuel consumptionIndicates the current average fuelconsumption.
70
Information Displays
Average fuel consumptionIndicates the average fuel consumptionsince the function was last reset.
Ford ECO modeEnters the ECO mode menu.
Average speedIndicates the average speed calculatedsince the function was last reset.
Outside air temperatureShows the outside air temperature.
Hold 'SET' to set Tyre Pres.Recalibrates the system to the actualpressure of the tyres. See Tyre PressureMonitoring System (page 165).
MenuEnters the main menu. See GeneralInformation (page 67).
Trip
Dist to empty
Instant Fuel
Average Fuel
Average Speed
Ford ECO Mode
Outside Air
Hold ‘SET’ to set Tyre Pres
Menu
E121684
Use the rotary control to scroll through thetrip computer displays.Note: The position of the trip computerdisplay may vary depending on theinformation shown in the display.
Resetting the trip computer using themain menuTo reset a particular display:1. Use the rotary control to enter the main
menu.2. Highlight Reset Trip.3. Press the SET/RESET button.4. Highlight the function to be reset.5. Press and hold the SET/RESET
button.
71
Information Displays
To reset all three displays, highlight All andpress and hold the SET/RESET button.
PERSONALISED SETTINGS1. Use the rotary to enter the main menu.2. Press the SET/RESET button to
choose a sub-menu and adjust thesettings.
ESPSelect this option to activate or deactivateESP.1. Use the rotary control to enter the main
menu.2. Highlight ESP and press the
SET/RESET.3. Highlight Back and repeatedly press
the SET/RESET button to return tothe main menu.
SteeringNote: For road safety reasons, changes inthe Steering menu can only be made whilethe vehicle is stationary. If this menu or oneof its sub-menus is open when the vehiclebegins to move, the information display willautomatically exit the Steering menu.Note: When the vehicle is stationary, thesteering assistance is optimized in all threesettings and does not differ noticeably.Standard: The standard setting is suitablefor all driving styles.Sport: The steering assistance is reduced.This suits a sportier driving style byincreasing the feedback through thesteering wheel. The sport setting is also anadvantage when driving on icy and snowyroad conditions.Comfort: The steering assistance isincreased. The steering will feel lighter andyou will not need to exert as much forceon the wheel.
1. Use the rotary control to enter the mainmenu.
2. Highlight Steering and press theSET/RESET button.
3. Highlight the desired setting and pressthe SET/RESET button to confirm thesetting.
4. Highlight Back and repeatedly pressthe SET/RESET button to return tothe main menu.
Clock setting1. Use the rotary control to enter the main
menu.2. Highlight Clock and press the
SET/RESET button.3. Highlight Set Clock and press the
SET/RESET button. The hours startto flash.
4. Use the rotary control to adjust thehours to the desired setting.
5. Press the SET/RESET button toconfirm the setting. The minutes startto flash.
6. Proceed in the same way to set theminutes and the date.
7. Press the SET/RESET button toconfirm the setting.
8. Highlight Back and repeatedly pressthe SET/RESET button to return tothe main menu.
Help screen and navigationinformationThe help screen appears for a few secondswhen you switch the ignition on.If the navigation is operating, informationrelating to this system is displayed in theinformation display.To select which information is displayedin the information display:
72
Information Displays
1. Use the rotary control to enter the mainmenu.
2. Highlight Setup and press theSET/RESET button.
3. Highlight Display and press theSET/RESET button.
4. Highlight Configure and press theSET/RESET button.
5. Highlight the desired setting and pressthe SET/RESET button to confirm thesetting.
6. Highlight Back and repeatedly pressthe SET/RESET button to return tothe main menu.
Navigation informationYou can also choose when the navigationinformation is displayed in the informationdisplay. Three options are available:• Always off: No navigation information
is displayed in the information display.• On guidance: The navigation
information will only appear when thenavigation system provides a guidanceinstruction. This function is onlyavailable on certain navigationsystems.
• Always on: Navigation information willalways appear in the informationdisplay when the navigation system isoperating.
To set when navigation information shouldbe displayed:1. Use the rotary control to enter the main
menu.2. Highlight Setup and press the
SET/RESET button.3. Highlight Display and press the
SET/RESET button.4. Highlight Configure and press the
SET/RESET button.
5. Highlight Nav Info and press theSET/RESET button.
6. Highlight the desired setting and pressthe SET/RESET button to confirm thesetting.
7. Highlight Back and repeatedly pressthe SET/RESET button to return tothe main menu.
Language settingA choice of eleven languages are available.English, German, Italian, French, Spanish,Turkish, Russian, Dutch, Polish, Swedishand Portuguese.1. Use the rotary control to enter the main
menu.2. Highlight Setup and press the
SET/RESET button.3. Highlight Display and press the
SET/RESET button.4. Highlight Language and press the
SET/RESET button.5. Highlight the desired setting and press
the SET/RESET button to confirm thesetting.
6. Highlight Back and repeatedly pressthe SET/RESET button to return tothe main menu.
Units of measureTo select metric or imperial units:Toggling the units of measure using thisdisplay will affect the following displays:• Distance to empty.• Average fuel consumption.• Instantaneous fuel consumption.• Average speed.• Outside air temperature.• The temperature display in the
automatic climate control.
73
Information Displays
Note: The units of measure for outside airtemperature and the automatic climatecontrol can be toggled independent of theother displays. When showing the outsideair temperature, press and hold theSET/RESET button for a short time.1. Use the rotary control to enter the main
menu.2. Highlight Setup and press the
SET/RESET button.3. Highlight Display and press the
SET/RESET button.4. Highlight Measure Unit and press the
SET/RESET button.5. Highlight the desired setting and press
the SET/RESET button to confirm thesetting.
6. Highlight Back and repeatedly pressthe SET/RESET button to return tothe main menu.
Chime deactivationThe following chimes can be deactivated:• Low fuel warning.• General warning messages.• General information messages.1. Use the rotary control to enter the main
menu.2. Highlight Setup and press the
SET/RESET button.3. Highlight Chimes and press the
SET/RESET button.4. Highlight the desired setting and press
the SET/RESET button to confirm thesetting.
5. Highlight Back and repeatedly pressthe SET/RESET button to return tothe main menu.
INFORMATION MESSAGES
E73265
E73266
Press SET/RESET to acknowledge andremove some messages from theinformation display. Other messages willbe removed automatically after a shorttime.With instrument cluster type 2 and 3,certain messages need to be confirmedbefore you can access the menus.
Message indicatorThe message indicatorilluminates to supplement somemessages. It will be red or amber
depending on the severity of the messageand will remain on until the cause of themessage has been rectified.
Message symbolsSee Owner’s handbook.
74
Information Displays
Have the system checked at thenext service.
Have the system checked assoon as possible.
Stop your vehicle as soon as it issafe to do so.
Viewing current messages1. Press the SET/RESET button to enter
the main menu.2. Scroll to the messages display using
the rotary control and press theSET/RESET button.
3. Turn the rotary control to scroll throughthe available messages.
4. Press SET/RESET twice to exit themenu.
All wheel drive
ActionWarning lampMessage
The vehicle can still be driven buthave the system checked by aproperly trained technician assoon as possible.
amberAWD overheated now disabled
Have your vehicle checked by aproperly trained technician.redAWD malfunction
Doors open
ActionWarning lampMessage
Vehicle is moving. Stop the vehicleas soon as safely possible andclose.
redDriver door open
Vehicle is moving. Stop the vehicleas soon as safely possible andclose.
redDriver side rear door open
Vehicle is moving. Stop the vehicleas soon as safely possible andclose.
redPassenger door open
Vehicle is moving. Stop the vehicleas soon as safely possible andclose.
redPassenger side rear door open
Vehicle is moving. Stop the vehicleas soon as safely possible andclose.
redLuggage comp. open
75
Information Displays
ActionWarning lampMessage
Vehicle is moving. Stop the vehicleas soon as safely possible andclose.
redBonnet open
Vehicle not moving. Close.amberDoor ajar close door
Keyless system
ActionWarning lampMessage
Have the system checked by aproperly trained technician.redImmobiliser malfunction
You will ONLY be able restart yourvehicle up to a maximum of fivetimes or for a period of up to 56hours after which the vehiclecannot be started. Have thesystem checked by a properlytrained technician as soon aspossible.
redSteering malfunction
See Keyless Entry (page 32).amberKey not detected
See Keyless Entry (page 32).amberKey outside car
See Changing the remotecontrol battery (page 28).amberRemote key battery low
Have the system checked by aproperly trained technician.-Steering malfunction
See Keyless Starting (page 99).-To start press brake
See Keyless Starting (page 99).-To start press clutch
76
Information Displays
Lighting
ActionWarning lampMessage
Brake lamp switch. The vehiclecan be driven as normal. However,cruise control cannot be switchedon. Have the system checked by aproperly trained technician assoon as possible.
redBrake light fault
Have the system checked by aproperly trained technician.amberAdaptive front light failure
Maintenance
ActionWarning lampMessage
Have the system checked by aproperly trained technician.redHigh engine temperature
See Brake and Clutch FluidCheck (page 147).redLow brake fluid level
Stop the vehicle as soon as safelypossible and switch off the engineimmediately. Have the systemchecked by a properly trainedtechnician immediately.
redEngine malfunction
Electronic acceleration control(EAC). The vehicle can be drivenbut the acceleration rate will benoticeably reduced. Maximumvehicle speed will be maintained.Have the system checked by aproperly trained technician assoon as possible.
redAcceleration reduced
Appears only on vehicles fittedwith headlamp washers. Thewasher fluid level is low. Check thewasher fluid level. See WasherFluid Check (page 148).
amberLow washer fluid level
Have the system checked by aproperly trained technician.-Service oil
77
Information Displays
Power steering
ActionWarning lampMessage
Full steering will be maintainedbut you will need to exert greaterforce on the steering wheel. Havethe system checked by a properlytrained technician as soon aspossible.
amberPower steering malfunction
Stability control (ESP)
ActionWarning lampMessage
Have the system checked by aproperly trained technician.amberESP malfunction
Transmission
ActionWarning lampMessage
Automatic transmission. Thevehicle can still be driven but havethe system checked by a properlytrained technician as soon aspossible.
amberTransmission limited function
Under certain driving conditions itis possible that the clutches in thetransmission can overheat. Inthese circumstances it is neces-sary to press the brake pedal andstop the vehicle to preventredTransm. too hot. Press brake damage to the transmission.Select N (NEUTRAL) or P(PARK) and apply the parkingbrake until the transmission hascooled and the message disap-pears from the display.
78
Information Displays
ActionWarning lampMessage
The transmission is too hot. Inthese extreme conditions thetransmission will disengage drivein order to prevent damage. Youwill not be able to drive until thetransmission has cooled.
redTransmission too hot
Have the system checked by aproperly trained technician.amberTransmission malfunction
At low outside temperatures, afterstarting the engine, it may take thetransmission several seconds toengage R (REVERSE) or D(DRIVE). Keep the brake pedaldepressed until these messagesdisappear from the display.
-Engagement in progressPress brake pedal
See Automatic Transmission(page 108). See Starting andStopping the Engine (page 99).
-Move shifter to P
Tyre pressure monitoring system
ActionWarning lampMessage
The pressure in one or more tyreshas dropped. Check as soon aspossible.
amberCheck tyre pressures
Permanent malfunction. Have thesystem checked by a properlytrained technician.
amberTyre Press. Sys malfunction
79
Information Displays
PRINCIPLE OF OPERATIONOutside airKeep the air intakes forward of thewindscreen free from obstruction (snow,leaves etc.) to allow the climate controlsystem to function effectively.
Recirculated airCAUTION
Prolonged use of recirculated air maycause the windows to mist up. If thewindows mist up, follow the settings
for defrosting and demisting thewindscreen.
The air currently in the passengercompartment will be recirculated. Outsideair will not enter the vehicle.
HeatingHeating performance depends on thetemperature of the engine coolant.
Air conditioningNote: The air conditioning operates onlywhen the temperature is above 4°C (39°F).Note: If you use the air conditioning, thefuel consumption of your vehicle will behigher.Air is directed through the evaporatorwhere it is cooled. Humidity is extractedfrom the air to help keep the windows freeof mist. The resulting condensation isdirected to the outside of the vehicle andit is therefore normal if you see a smallpool of water under your vehicle.
General information on controllingthe interior climateFully close all the windows.
Warming the interiorDirect the air towards your feet. In cold orhumid weather conditions, direct some ofthe air towards the windscreen and thedoor windows.
Cooling the interiorDirect the air towards your face.
AIR VENTS
E77930
80
Climate Control
MANUAL CLIMATE CONTROLAir distribution control
A
F B
C
D
E
E71379
WindscreenAFootwell and windscreenBFootwellCFace level and footwellDFace levelEFace level and windscreenF
You can set the air distribution control toany position between the symbols.
Blower
E75470
A
OffANote: If you switch the blower off, thewindscreen may mist up.
Recirculated air
E73059
Press the button to togglebetween outside air andrecirculated air.
Heating the interior quickly
E71377
81
Climate Control
Ventilation
E71378
Set the air distribution control, blower andair vents to suit your requirements.
Air conditioningSwitching the air conditioning on andoff
If you turn the blower off, the airconditioning will turn off. Whenyou turn the blower on again,
the air conditioning will come onautomatically.
Cooling with outside air
E71380
Cooling the interior quickly
E71381
Defrosting and demisting thewindscreen
E71382
When the temperature is above 4°C(39°F), the air conditioning will switch onautomatically. Make sure that the bloweris on. The indicator in the switch willilluminate during defrosting and demisting.If you move the air distribution control toa position other than A, the A/C willremain on.You can switch the air conditioning andrecirculated air on and off while the airdistribution control is set to position A.If necessary, switch the heated windowson. See Heated Windows and Mirrors(page 85).Note: To defrost or demist the rear sidewindows, set the second row air vents tothe defrosting and demisting position. SeeAir Vents (page 80).
Reducing interior air humidity
E71383
82
Climate Control
AUTOMATIC CLIMATE CONTROL
E91390
The system controls the temperature,amount and distribution of the air flowautomatically and adjusts them accordingto the driving and weather conditions.Pressing the AUTO button once switcheson the auto mode.The system in your vehicle is dual-zoneautomatic climate control. When thesystem is in mono mode, all thetemperature zones are linked to the driver'szone. When you switch mono mode off,the dual-zone system allows you to setdifferent temperatures for the driver's andfront passenger's side.Note: Avoid adjusting the settings whenthe vehicle interior is extremely hot or cold.The automatic climate control adjusts tothe current circumstances automatically.For the system to function properly, the sideand centre vents should be fully open.Note: The sunload sensor is located on topof the instrument panel. Do not cover thesensor with any objects.Note: At low outside temperatures, whenthe system is in auto mode, the air streamwill be directed to the windscreen and theside windows as long as the engine is cold.
Note: For information on the automaticclimate control, on vehicles fitted with acombined Navigation and automaticclimate control system, see separatehandbook.
Setting the temperature
E91391
You can set the temperature between15.5ºC (60°F) and 29.5ºC (85°F) in stepsof 0.5ºC (1°F). In position LO, 15ºC (59°F),the system will switch to permanentcooling. In position HI, 30°C (86°F), thesystem will switch to permanent heating.Note: If either position LO or HI is selected,the system will not regulate a stabletemperature.
Mono modeIn mono mode, the temperature settingsfor both the driver’s and passenger’s sideare linked. If you adjust the temperatureusing the rotary control on the driver’s side,the settings will be adjusted to the samesetting on the passenger’s side. In monomode, MONO appears in the display.
83
Climate Control
To switch mono mode offSelect a temperature for the passenger’sside with the rotary control on thepassenger’s side. Mono mode will switchoff and MONO disappears from thedisplay. The temperature for the driver’sside will remain unchanged. You can nowadjust the driver and passenger sidetemperatures independently of eachanother. The temperature settings for eachside are shown in the display. You can seta temperature difference of up to 4ºC(8°F).Note: If you set a temperature differenceof greater than 4ºC (8°F), the temperatureon the other side will be adjusted so thatthe difference remains 4ºC (8°F).Note: If you set one of the sides to HI or LO,both sides will be set to HI or LO.
To switch mono mode back on
E70306
To switch mono mode back on,press the MONO button.MONO reappears in the display
and the passenger’s side temperature willbe adjusted to the driver’s sidetemperature.
BlowerUse the buttons to adjust theblower speed.
The blower setting is indicated in thedisplay.To return to auto mode, press the AUTObutton.
Air distributionTo adjust air distribution, press the desiredbutton. Any combination of settings canbe selected simultaneously.
E70308
A B C
FootwellAFace levelBWindscreenC
When you select windscreen defrostingand demisting, A, B and C switch offautomatically and the air conditioningswitches on. Outside air will flow into thevehicle. You cannot select recirculated air.
Windscreen defrosting anddemisting
E91392
Press the windscreen defrostingand demisting button. Outsideair will flow into the vehicle. Air
conditioning is automatically selected. Aslong as the air distribution is set to thisposition, you cannot select recirculated air.
The blower speed and the temperaturecontrol operate automatically and cannotbe adjusted manually. The blower is set tohigh speed and the temperature to HI.When you select windscreen defrostingand demisting, the heated screens switchon automatically and switch off after ashort time.To return to auto mode, press the AUTObutton.
Switching the air conditioning onand off
E91393
Press the A/C button to switchthe air conditioning on and off.A/C OFF appears in the display
when the air conditioning is switched off.
84
Climate Control
A/C ON appears in the display when theair conditioning is switched on.
Recirculated airPress the recirculated air buttonto toggle between outside airand recirculated air.
Note: When the system is in auto mode andthe interior and exterior temperatures arequite hot, the system selects recirculatedair automatically to maximise cooling of theinterior. Once the selected temperature isreached, the system will reselect outside airautomatically.
Switching off the automaticclimate control
E91394
Press the OFF button.
When switched off, the heating, ventilationand air conditioning system is switched offand recirculated air is selected.
HEATED WINDOWS ANDMIRRORSHeated windowsUse the heated windows to defrost ordemist the windscreen or rear window.Note: The heated windows operate onlywhen the engine is running.
Heated windscreen
E72506
Heated rear window
E72507
Heated exterior mirrorsElectric exterior mirrors are fitted with aheating element that will defrost or demistthe mirror glass. They will switch onautomatically when you switch the heatedrear window on.
AUXILIARY HEATERParking heater
WARNINGSThe parking heater must not beoperated at filling stations, nearsources of combustible vapours or
dust or in enclosed spaces.The parking heater should beswitched on for approximately 10minutes at least once a month all
year round. This prevents the water pumpand heater motor from seizing.
Note: The parking heater will only operateif there is at least 7.5 litres (1.6 gallons) offuel in the fuel tank and the ambienttemperature is below 15°C (59°F). Theheater will not operate if the battery is low.Note: The heating depends on the outsideair temperature.Note: When the parking heater is activated,exhaust fumes may come from under thesides of the vehicle. This is normal.Note: On vehicles with manual climatecontrol the heating of the vehicle interior isdependent on the temperature, airdistribution and blower control settings.The parking heater operates independentlyof the vehicle heater by heating theengine’s coolant circuit. It is fed from thevehicle fuel tank. You can also use it whilethe vehicle is in motion to help the vehicleheater warm up the interior more quickly.
85
Climate Control
Used properly, the parking heater providesthe following benefits:• It preheats the interior of the vehicle.• It keeps the windows clear of ice in the
event of frost and preventscondensation.
• It avoids cold starts and allows theengine to reach operating temperaturesooner.
To prevent the battery from discharging:• Once the parking heater has performed
one heating cycle, the nextprogrammed heating cycle will only becarried out if you have started thevehicle’s engine in between.
• After a heating cycle, drive the vehiclefor at least the period of the heatingcycle.
Programming the parking heaterNote: The programmed time is the time atwhich you wish the vehicle to be warm andready to drive, not the time at which theheater switches on.Note: You must programme the times atleast 70 minutes in advance of the time youwish to set.Note: You must set the time and datecorrectly.To programme the heating times:
E73265
E73266
1. Use the rotary control to enter the mainmenu.
2. Highlight Park Heater and press theSET/RESET button.
E74467
One-Time
Program 1Program 2
Active now
Park Heater
• The functions Program 1 andProgram 2 allow you to programmeup to two heating cycles for each dayof the week. These times will remainstored and the heater will warm up thevehicle at these times on these daysevery week.
• The function One-Time allows you toprogramme one heating cycle for onespecific day.
• The function Active nowautomatically switches on the heater.
86
Climate Control
Programming the functions Program 1and Program 2
E74468
FridayThursday
TuesdayMonday
Wednesday
[07:55]
Program 1
1. Use the rotary control to enter the mainmenu.
2. Highlight Program 1 and press theSET/RESET button.
3. Highlight the day on which the heatershould warm up the vehicle.
4. Press the SET/RESET button toconfirm the selection. A cross appearsin the box next to the day to show thatthis day is selected.
5. Continue in the same way to select allthe days on which the heater shouldwarm up the vehicle.
6. To set the time at which the vehicleshould be warmed up, highlight thetime at the top of the display and pressthe SET/RESET button. The hoursstart to flash.
7. Use the rotary control to adjust thehours to the desired setting.
8. Press the SET/RESET button toconfirm the setting. The minutes startto flash.
9. Use the rotary control to adjust theminutes to the desired setting.
10. Press the SET/RESET button toconfirm the setting.
11. Press the SET/RESET button to exitthe menu.
E74469
07:5501:12:2006
ParkheaterProgram 1
OK = change
You can use the function Program 2 to seta second cycle, for example different timeson different days or twice on the same day.The programming procedure is the sameas for the function Program 1.
Programming the function One-Time1. Highlight One-Time and press the
SET/RESET button. The hours startto flash.
2. Use the rotary control to adjust thehours to the desired setting.
3. Press the SET/RESET button toconfirm the setting. The minutes startto flash.
4. Use the rotary control to adjust theminutes to the desired setting.
5. Press the SET/RESET button toconfirm the setting.
6. Press the SET/RESET button to exitthe menu.
87
Climate Control
Active now1. Highlight Active now and press the
SET/RESET button. A cross appearsin the box next to the function to showthat the heater is activated.
To deactivate the heater, highlight Activenow and press the SET/RESET buttonagain.
Diesel auxiliary heater (dependingon country)The diesel auxiliary heater (PTC electricalheater) aids in warming the engine and thevehicle interior on vehicles with a dieselengine. It is switched on or offautomatically depending on the outsideair temperature, the coolant temperatureand the alternator load.
Fuel operated heater (dependingon country)The fuel operated heater aids in warmingthe engine and the vehicle interior onvehicles with a petrol or diesel engine. It isswitched on or off automaticallydepending on the outside air temperatureand the coolant temperature, unless youhave deactivated it. When the fueloperated heater is operating, a messageappears in the information display. SeeInformation Displays (page 67).To deactivate the fuel operated heater:1. Use the rotary control to enter the main
menu.2. Highlight Setup and press the
SET/RESET button.3. Highlight Aux. Heater and press the
SET/RESET button. A cross appearsin the box when the heater is activated.
4. Press the SET/RESET button to exitthe menu.
88
Climate Control
SITTING IN THE CORRECTPOSITION
E68595
WARNINGSDo not adjust the seats when thevehicle is moving.Only when you use the seat beltproperly, can it hold you in a positionthat allows the airbag to achieve its
optimum effect.
When you use them properly, the seat,head restraint, seat belt and airbags willprovide optimum protection in the eventof a collision. We recommend that you:• sit in an upright position with the base
of your spine as far back as possible.• do not recline the seatback more than
30 degrees.• adjust the head restraint so that the
top of it is level with the top of yourhead and as far forwards as possible,remaining comfortable.
• keep sufficient distance betweenyourself and the steering wheel. Werecommend a minimum of 250millimetres (10 inches) between yourbreastbone and the airbag cover.
• hold the steering wheel with your armsslightly bent.
• bend your legs slightly so that you canpress the pedals fully.
• position the shoulder strap of the seatbelt over the centre of your shoulderand position the lap strap tightly acrossyour hips.
Make sure that your driving position iscomfortable and that you can maintain fullcontrol of your vehicle.
HEAD RESTRAINTSAdjusting the head restraint
WARNINGSRaise the rear head restraint whenthe rear seat is occupied by apassenger.When using a forward facing childrestraint on a rear seat, alwaysremove the head restraint from that
seat.
E66539
Adjust the head restraint so that the topof it is level with the top of your head.
Removing the head restraintPress the locking buttons and remove thehead restraint.
89
Seats
MANUAL SEATSAll vehicles
WARNINGSDo not use any accessory seat coversthat are not specifically designed forseats with side airbags. These seat
covers must be fitted by properly trainedtechnicians.
Do not adjust the seats while thevehicle is moving.
Moving the seats forwards orbackwards
E70728
Pull the lever. Rock the seat to engage thecatch.
Adjusting the lumbar support
E78058
Adjusting the height of the driver’s seat
E70730
Each pull or press on the lever will raise orlower the height by a small amount.
90
Seats
Adjusting the angle of the seatback
E70731
When the seats are slid fully forward theseatbacks can be fully reclined.
POWER SEATS6-way electric seat
E78060
REAR SEATS
WARNINGSWhen folding the seatbacks down,take care not to get your fingerscaught between the seatback and
seat frame.
WARNINGSMake sure that the seats and theseatbacks are secure and fullyengaged in their catches.
91
Seats
Folding the seatbacks downCAUTION
Lower the head restraints.
1
2
1
E86611
1. Press the unlock buttons down andhold them there.
2. Push the seatback forwards.
Creating a level load floorWARNING
Make sure the red indicator is notshowing when you engage the seatin the catches.
CAUTIONLower the head restraints.
2
13
2
E86612
1. Insert your fingers between the seatcushion and seatback and fold the seatcushion forwards.
2. Press the unlock buttons down andhold them there.
3. Push the seatback forwards.
Folding the seatbacks upWARNING
When folding the seatbacks up,make sure that the belts are visibleto an occupant and not caught
behind the seat.
HEATED SEATS
CAUTIONOperating this function with theengine off will drain the battery.
The heated front seats are operated byrotary controls in the instrument panel. Foritem location: See At a Glance (page 10).The maximum temperature is reachedafter five or six minutes. It is regulatedthermostatically.The seat heating will operate only whenthe ignition is on.
92
Seats
SUN SHADESPanoramic roof
E91500
The roof blind is in two sections. Pull thehandle from the front or rear of thepanoramic roof and fully extend therequired section.To open the blind, slightly pull the handleagainst the spring mechanism, and pushup to release from the hooks.Note: Each blind section will only extendto the middle of the panoramic roof.
INSTRUMENT LIGHTINGDIMMER
E70454
CUP HOLDERS
WARNINGDo not place hot drinks in the cupholders when the vehicle is moving.
Seat back traysWARNING
Do not use the trays when the vehicleis moving. Make sure that you securethe trays in the lowered position
before setting off.
93
Convenience features
E72630
CIGAR LIGHTER
CAUTIONSIf you use the socket when the engineis not running, the battery maydischarge.Do not hold the cigar lighter elementpressed in.
Note: Switch the ignition on to use the cigarlighter. You can also use it for up to 30minutes after you have switched the ignitionoff.Note: You can use the socket to power 12volt appliances that have a maximumcurrent rating of 15 Amperes. Use only Fordaccessory connectors or connectorsspecified for use with SAE standard sockets.
E72972
Press the element in to use the cigarlighter. It will pop out automatically.
AUXILIARY POWER POINTS
CAUTIONIf you use the socket when the engineis not running, the battery maydischarge.
Note: You can use the socket to power 12volt appliances that have a maximumcurrent rating of 10 Amperes. Use only Fordaccessory connectors or connectorsspecified for use with SAE standard sockets.
E78056
Auxiliary power sockets are located in thecentre console and in the luggagecompartment.
Power inverterCAUTIONS
If you use the socket when the engineis not running, the battery maydischarge.If the LED flashes continuously,re-insert the plug or switch the ignitionoff and then on again.It will switch off if the temperature isabove 85°C (185°F). The LED willflash once. When it has cooled down
it will switch back on automatically.
94
Convenience features
CAUTIONSDo not exceed the maximum poweroutput. If you do, the LED will flashtwice. Remove the plug and re-insert
it.If the LED flashes three or four times,have the system checked by aproperly trained technician.
Note: You can use the socket to power 230volt appliances that have a maximum ratingof 150 watts.
E98199
STORAGE COMPARTMENTSFront storage compartment
E99181
Note: Avoid keeping heat-sensitive objectsand liquids in the front storagecompartment.
Storage area under the rear seats
E99182
95
Convenience features
To gain access to the storage area, fold upthe rear seat cushions. See Rear Seats(page 91).Note: Do not overload the storage areasunder the rear seats. Ensure that the rearseat cushions can be folded backcompletely.
GLASSES HOLDER
E75193
TOLL READER
E99272
40
13
70
120
On vehicles with an anti-heat windscreen,toll readers should be placed in the areaas shown (all measurements shown inmillimetres), otherwise communicationperformance with toll stations may bereduced.The toll reader should be placed on thepassenger side to prevent the reader fromobscuring the driver’s vision (e.g. at trafficlights).
CD CHANGERThis is located under the front passengerseat.
AUXILIARY INPUT (AUX IN)SOCKETSee separate audio handbook.
96
Convenience features
E91511
E92035
USB PORTSee Using a USB device (page 222).
E91511
E99438
97
Convenience features
SATELLITE NAVIGATION UNITHOLDERAdjusting the holder
E112711
1
3
2
1. Unlock.2. Adjust the holder to the desired
position.3. Lock.Note: Make sure that the navigation unitholder is locked in position.
FLOOR MATS
WARNINGWhen using the floor mats, alwaysmake sure the floor mat is properlysecured using the appropriate fixings
and positioned so that it does not interferewith the operation of the pedals.
98
Convenience features
GENERAL INFORMATIONGeneral points on startingIf the battery has been disconnected thevehicle may exhibit some unusual drivingcharacteristics for approx. 8 kilometres (5miles) after reconnecting the battery.This is because the engine managementsystem must realign itself with the engine.Any unusual driving characteristics duringthis period may be disregarded.
Starting the engine by towing orpushing
WARNINGTo prevent damage you must notpush or tow start your vehicle. Usebooster cables and a booster battery.
See Jump-Starting the Vehicle (page153).
KEYLESS STARTING
WARNINGSThe keyless starting system may notfunction if the key is close to metalobjects or electronic devices such as
mobile phones.Always check that the steering wheellock is deactivated beforeattempting to move your vehicle.
Note: A valid passive key must be locatedinside the vehicle to switch the ignition onand start the engine.Note: To start your engine you must alsofully depress the brake or clutch pedal,depending on the transmission fitted.
E85766
Ignition onPress the start button once. All electricalcircuits are operational, warning lamps andindicators illuminate.
Starting with automatictransmissionNote: Releasing the brake pedal duringengine start will stop the engine crankingand return to ignition on.1. Make sure the transmission is in P or
N.2. Fully depress the brake pedal.3. Briefly press the start button.
Starting with manual transmissionNote: Releasing the clutch pedal duringengine start will stop the engine crankingand return to ignition on.1. Fully depress the clutch pedal.2. Briefly press the start button.
Starting a diesel engineNote: Engine cranking will not commenceuntil the engine glow plug cycle has beencompleted. This may take several secondsin extremely cold conditions.Note: Continue to press the clutch or brakepedal until engine cranking begins.
99
Starting and Stopping the Engine
Failure to startThe passive starting system will notfunction if:• The passive key frequencies are
jammed.• The passive key battery is flat.If you are unable to start your vehicle carryout the following procedure.
E99666
1. Hold the key next to the steeringcolumn shroud exactly as shown.
2. With the key in this position you canuse the start button to switch theignition on and start your vehicle.
If you are still unable to start your vehiclecarry out the following procedure.
E87381
1. Carefully prise out the cover.
2. Remove the key blade. See KeylessEntry (page 32).
E99586
3. Insert the key blade into the key holder.4. With the key blade in this position you
can use the start button to switch theignition on and start your vehicle.
Stopping the engine with thevehicle stationaryNote: The ignition, all electrical circuits,warning lamps and indicators will beswitched off.When your vehicle is stationary, press thestart button to stop the engine. Theignition, all electrical circuits, warninglamps and indicators will be switched off.
Manual transmissionPress the start button.
Automatic transmission1. Move the selector lever to position P.2. Press the start button.
100
Starting and Stopping the Engine
Stopping the engine when thevehicle is moving
WARNINGSwitching off the engine when thevehicle is still moving will result in aloss of brake and steering assistance.
The steering will not be locked, but highereffort will be required. When the ignition isswitched off some electrical circuits,warning lamps and indicators may also beOFF.
Press and hold the start button for twoseconds, or press three times within threeseconds.
DIESEL PARTICULATE FILTERThe DPF forms part of the emissionsreduction systems fitted to your vehicle. Itfilters harmful diesel particulates (soot)from the exhaust gas.
RegenerationWARNING
Do not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The DPF
regeneration process creates very highexhaust gas temperatures and the exhaustwill radiate a considerable amount of heatduring and after DPF regeneration, andafter you have switched the engine off.This is a potential fire hazard.
CAUTIONAvoid running out of fuel.
Note: During regeneration at low speed orengine idle, you may smell a hot metallicodour and could notice a clicking metallicsound. This is due to the high temperaturesreached during regeneration and is normal.Note: After you have switched your engineoff the fans may continue to run for a shortperiod of time.Unlike a normal filter which requiresperiodic replacement, the DPF has beendesigned to regenerate, or clean itself tomaintain operating efficiency. Theregeneration process takes placeautomatically. However, some drivingconditions mean that you may need tosupport the regeneration process.If you drive only short distances or yourjourneys contain frequent stopping andstarting, where there is increasedacceleration and deceleration, occasionaltrips with the following conditions willassist the regeneration process:• Drive your vehicle at a constant speed,
preferably on a main road or motorway,for up to 20 minutes.
• Avoid prolonged idling and alwaysobserve speed limits and roadconditions.
• Do not switch off the ignition.• Use a lower gear than normal to
maintain a higher engine speed duringthis journey, where appropriate.
SWITCHING OFF THE ENGINEVehicles with a turbocharger
CAUTIONDo not switch the engine off when itis running at high speed. If you do, theturbocharger will continue running
after the engine oil pressure has droppedto zero. This will lead to prematureturbocharger bearing wear.
101
Starting and Stopping the Engine
Release the accelerator pedal. Wait untilthe engine has reached idle speed and thenswitch it off.
102
Starting and Stopping the Engine
SAFETY PRECAUTIONS
WARNINGSStop refuelling after the fuel nozzlestops the second time. Additionalfuel will fill the expansion space in
the fuel tank which could lead to fueloverflowing. Fuel spillage could behazardous to other road users.
Do not use any kind of flames or heatnear the fuel system. The fuel systemis under pressure. There is a risk of
injury if the fuel system is leaking.
FUEL QUALITY - PETROL
CAUTIONDo not use leaded petrol or petrol withadditives containing other metalliccompounds (e.g. manganese-based).
They could damage the emission system.
Note: We recommend that you use onlyhigh quality fuel without additives or otherengine treatments.Use minimum 95 octane unleadedpetrol that meets the specification definedby EN 228, or equivalent.
FUEL QUALITY - DIESEL
WARNINGDo not mix diesel with oil, petrol orother liquids. This could cause achemical reaction.
CAUTIONSDo not add kerosene, paraffin orpetrol to diesel. This could causedamage to the fuel system.
CAUTIONSUse diesel that meets thespecification defined by EN 590, orthe relevant national specification.
Note: We recommend that you use onlyhigh quality fuel.Note: The use of additives or other enginetreatments not approved by Ford is notrecommended.Note: We do not recommend the prolongeduse of additives intended to prevent fuelwaxing.
Long-term storageMost diesel fuels contain bio-diesel, it isrecommended to fill the tank with purelymineral diesel (where available) or add ananti-oxidant prior to long-term storage ofyour vehicle exceeding two months. Yourdealer can help you with a suitableanti-oxidant.
FUEL FILLER FLAP
WARNINGSTake care when refuelling to avoidspilling any residual fuel from the fuelnozzle.Do not use any kind of flames or heatnear the fuel system. The fuel systemis under pressure. There is a risk of
injury if the fuel system is leaking.
CAUTIONIf you use a high pressure spray towash your vehicle, only spray the fuelfiller flap briefly from a distance not
less than 200 millimetres (8 inches).
103
Fuel and Refuelling
E86613
1. Open the flap fully until it engages.
E139202
A
A
Note: When you insert the fuel nozzle, aspring loaded inhibitor will open if thecorrect size nozzle is detected. This helpsto avoid filling up with the wrong fuel.2. Insert the fuel nozzle up to and
including the first notch on the nozzleA. Keep it resting on the cover of thefuel pipe opening.
WARNINGStop refuelling after the fuel nozzlestops the second time. Additionalfuel will fill the expansion space in
the fuel tank which could lead to fueloverflowing. Fuel spillage could behazardous to other road users.
E139203
A
B
Incorrect positionACorrect positionB
3. Do not lift the nozzle during refilling. Thiscan affect the flow of fuel and shut off ofthe fuel nozzle before the fuel tank is full.
E139205
104
Fuel and Refuelling
4. Operate the nozzle within the areashown.
WARNINGSWe recommend that you remove thefuel nozzle slowly to allow anyresidual fuel to drain into the fuel
tank. Alternatively you can wait 10 secondsbefore removing the fuel nozzle.
Do not remove the nozzle from itsfully inserted position during theentire refuelling process.
E119081
5. Slightly raise the fuel nozzle to removeit.
Refuelling with a fuel canUse the funnel which is located in the glovebox.
CATALYTIC CONVERTER
WARNINGDo not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The exhaust
will radiate a considerable amount of heatduring use, and after you have switchedthe engine off. This is a potential firehazard.
Driving with a catalytic converterCAUTIONS
Avoid running out of fuel.
Do not crank the engine for longperiods.Do not run the engine when a sparkplug lead is disconnected.Do not push-start or tow-start yourvehicle. Use booster cables. SeeJump-Starting the Vehicle (page
153).Do not switch the ignition off whendriving.
REFUELLING
CAUTIONDo not attempt to start the engine ifyou have filled the fuel tank with theincorrect fuel. This could damage the
engine. Have the system checked by aproperly trained technician immediately.
FUEL CONSUMPTIONThe CO2 and fuel consumption figures arederived from laboratory tests according toEEC Directive 80/1268/EEC andsubsequent amendments and are carriedout by all vehicle manufacturers.They are intended as a comparisonbetween makes and models of vehicles.They are not intended to represent the realworld fuel consumption you may get fromyour vehicle. Real world fuel consumptionis governed by many factors including;driving style, high speed driving, stop/startdriving, air conditioning usage, theaccessories fitted and towing etc.Your Ford dealer can give you advice onimproving your fuel consumption.
105
Fuel and Refuelling
TECHNICAL SPECIFICATIONS
6-speed manual transmission - 2WDFuel Consumption Figures
CO2 Emis-sionsCombinedExtra-UrbanUrban
Variantg/kml/100 km
(mpg)l/100 km
(mpg)l/100 km
(mpg)
1545.9 (47.9)5.0 (56.5)7.4 (38.2)2.0L Duratorq-TDCi stage V
5-speed automatic transmission - AWDFuel Consumption Figures
CO2 Emis-sionsCombinedExtra-UrbanUrban
Variantg/kml/100 km
(mpg)l/100 km
(mpg)l/100 km
(mpg)
24410.3 (27.4)7.8 (36.2)14.6 (19.3)2.5L Duratec
6-speed manual transmission - AWDFuel Consumption Figures
CO2 Emis-sionsCombinedExtra-UrbanUrban
Variantg/kml/100 km
(mpg)l/100 km
(mpg)l/100 km
(mpg)
1596.0 (47.1)5.1 (55.4)7.6 (37.2)2.0L Duratorq-TDCi stage V
2349.9 (28.5)7.6 (37.2)13.9 (20.3)2.5L Duratec
106
Fuel and Refuelling
6-speed automatic transmission - AWDFuel Consumption Figures
CO2 Emis-sionsCombinedExtra-UrbanUrban
Variantg/kml/100 km
(mpg)l/100 km
(mpg)l/100 km
(mpg)
1796.8 (41.5)5.8 (48.7)8.5 (33.2)2.0L Duratorq-TDCi stage V
107
Fuel and Refuelling
MANUAL TRANSMISSION
CAUTIONDo not engage reverse gear when thevehicle is moving. This can causedamage to the transmission.
E99067
On some vehicles it is necessary to raisethe collar whilst selecting reverse gear.
AUTOMATIC TRANSMISSIONSelector lever positions
E80836
S
ParkPReverseR
NeutralNDriveDSport mode and manual shiftingS
WARNINGApply the brakes before moving theselector lever and keep them applieduntil you are ready to move off.
Note: A cold engine has a higher idle speed.This will increase the tendency for yourvehicle to creep when you have selected adrive gear.Press the button on the selector lever toselect reverse and park.The selector lever position will be shownin the information display.
Park
WARNINGSSelect park only when your vehicleis stationary.Apply the parking brake andselect park before leaving yourvehicle. Make sure that the selector
lever is latched in position.
Note: An audible warning will sound if youopen the driver's door and you have notselected park.In this position, power is not transmittedto the drive wheels and the transmissionis locked. You can start the engine with theselector lever in this position.
Reverse
WARNINGSelect reverse only when your vehicleis stationary and the engine is at idlespeed.
108
Transmission
NeutralIn this position, power is not transmittedto the drive wheels but the transmission isnot locked. You can start the engine withthe selector lever in this position.
DriveSelect drive to shift automatically throughthe forward gears.The transmission will select theappropriate gear for optimum performancebased on ambient temperature, roadgradient, vehicle load and driver input.
Manual shifting - Vehicles with a5 speed transmission
WARNINGDo not hold the selector leverpermanently in – or +.
CAUTIONThe transmission will automaticallydownshift when the engine speed istoo low and upshift when too high.
Note: A shift will occur only when thevehicle speed and the engine speed areappropriate.Note: In Select mode the current gear (1,2, 3, 4 or 5) will be displayed on theinstrument panel.Move the selector lever to position S.Push the selector lever forwards to shiftdown and pull it backwards to shift up.Gears may be skipped by moving theselector lever repeatedly at short intervals.Manual mode also provides a kickdownfunction. See Kickdown.
Sport mode and manual shifting -Vehicles with a 6 speedtransmissionNote: A shift will occur only when thevehicle speed and the engine speed areappropriate.Note: In Sport mode the transmissionoperates as normal but gears are selectedmore quickly and at higher engine speeds.Note: In Sport mode S will be displayed onthe instrument panel.
Sport ModeActivate Sport mode by moving theselector lever to position S. Sport modewill remain active until either you shiftmanually up or down the gears or returnthe selector lever to position D.
Manual shifting
WARNINGDo not hold the selector leverpermanently in – or +.
CAUTIONThe transmission will automaticallydownshift when the engine speed istoo low and upshift when too high.
Push the selector lever forwards to shiftdown and pull it backwards to shift up.Gears may be skipped by moving theselector lever repeatedly at short intervals.Manual mode also provides a kickdownfunction. See Kickdown.
Hints on driving with an automatictransmissionMoving off1. Release the parking brake.
109
Transmission
2. Release the brake pedal and press theaccelerator pedal.
Stopping1. Release the accelerator pedal and
press the brake pedal.2. Apply the parking brake.
KickdownPress the accelerator pedal fully with theselector lever in the drive position to selectthe next lowest gear for optimumperformance. Release the acceleratorpedal when you no longer requirekickdown.
Emergency park position releaseleverUse the lever to move the selector leverfrom the park position in the event of anelectrical malfunction or if your vehicle hasa flat battery.
1
3
24
S
E125156
1. Insert a small flat-bladed tool into theslot.
2. Turn the tool through 90 degrees.3. Push downwards on the tool to detach
the gaiter frame from the trim panel.4. Push downwards on the gaiter frame
to release the lever and move theselector lever from the park position.
5. Pull upwards on the gaiter until thegaiter frame engages in the trim panel.
Note: If position P is selected again, thisprocedure must be repeated.
110
Transmission
ALL-WHEEL DRIVE
CAUTIONA vehicle fitted with AWD must berecovered with either ALL wheels onthe ground or ALL wheels off the
ground. See Vehicle recovery (page 139).
The AWD system, fitted to certainfront-wheel drive variants, willautomatically provide driving torque to therear wheels when road conditions becomeslippery with rain, snow or ice etc.
111
Transmission
PRINCIPLE OF OPERATIONDisc brakesWet brake discs result in reduced brakingefficiency. Dab the brake pedal whendriving from a car wash to remove the filmof water.
ABSWARNING
The ABS does not relieve you of yourresponsibility to drive with due careand attention.
The ABS helps you to maintain full steeringand directional stability when you brakeheavily in an emergency, by preventing theroad wheels from locking.
HINTS ON DRIVING WITHANTI-LOCK BRAKESWhen the ABS is operating, the brake pedalwill pulse. This is normal. Maintain pressureon the brake pedal.The ABS will not eliminate the dangersinherent when:• you drive too close to the vehicle in
front of you.• the vehicle is aquaplaning.• you take corners too fast.• the road surface is poor.
PARKING BRAKE
WARNINGVehicles with an automatictransmission should always be leftwith the selector lever in position P
(Park).
• Press the foot brake pedal firmly.• Pull the parking brake lever up smartly
to its fullest extent.• Do not press the release button while
pulling the lever up.• If your vehicle is parked on a hill and
facing uphill, select first gear or P(Park) and turn the steering wheelaway from the kerb.
• If your vehicle is parked on a hill andfacing downhill, select reverse gear orP (Park) and turn the steering wheeltowards the kerb.
To release the parking brake, press thebrake pedal firmly, pull the lever up slightly,depress the release button and push thelever down.
112
Brakes
PRINCIPLE OF OPERATIONElectronic stability programme(ESP)
WARNINGESP does not relieve you of yourresponsibility to drive with due careand attention.
E72903
A A
AB
B
B
B
without ESPAwith ESPB
The ESP supports stability when thevehicle starts to slide away from yourintended path. This is performed by brakingindividual wheels and reducing enginetorque as needed.The system also provides an enhancedtraction control function by reducingengine torque and may brake individualwheels if they spin when you accelerate.This improves your ability to pull away onslippery roads or loose surfaces, andimproves comfort by limiting wheel spin inhairpin bends.
Stability control (ESP) warning lampThe ESP warning lamp will flash when thesystem is operating. See Warning Lampsand Indicators (page 63).
Emergency brake assistWARNING
Emergency brake assist does notrelieve you of your responsibility todrive with due care and attention.
Emergency brake assist will detect whenyou brake heavily by measuring the rate atwhich you press the brake pedal. It willprovide maximum braking efficiency aslong as you press the pedal. Emergencybrake assist can reduce stopping distancesin critical situations.
Trailer stability controlWARNING
Trailer stability control does notrelieve you of your responsibility totow with due care and attention.
Trailer stability control is an enhancedfeature of ESP, and automatically detectswhen an attached trailer starts to sway.If this situation occurs, the system willautomatically brake individual wheels tostabilise the trailer and vehicle. In case avery severe sway is detected, the enginetorque will be reduced and the vehicle willbe slowed automatically.
USING STABILITY CONTROLNote: The system will be switched onautomatically every time you switch theignition on.To turn the system off and on. SeeInformation Displays (page 67).
113
Stability Control
PRINCIPLE OF OPERATION
WARNINGThe parking aid does not relieve youof your responsibility to drive withdue care and attention.
CAUTIONSVehicles fitted with a trailer towmodule not approved by us may notcorrectly detect obstacles.The sensors may not detect objectsin heavy rain or other conditions thatcause disruptive reflections.The sensors may not detect objectswith surfaces that absorb ultrasonicwaves.The parking aid does not detectobstacles moving away from thevehicle. They will only be detected
shortly after they start to move towardsthe vehicle again.
Take particular care when reversingwith a tow ball arm or rear fittedaccessories e.g. a bicycle carrier, as
the rear parking aid will only indicate thedistance from the bumper to the obstacle.
If you use a high pressure spray towash your vehicle, only spray thesensors briefly from a distance not
less than 20 centimetres (8 inches).
Note: On vehicles fitted with a tow ballarm, the parking aid is deactivatedautomatically when any trailer lamps (orlighting boards) are connected to the 13-pinsocket via a trailer tow module we haveapproved.Note: Keep the sensors free from dirt, iceand snow. Do not clean with sharp objects.
Note: The parking aid may emit false tonesif it detects a signal using the samefrequency as the sensors or if the vehicle isfully laden.Note: The outer sensors may detect theside walls of a garage. If the distancebetween the outer sensor and the side wallremains constant for three seconds, thetone will switch off. As you continue, theinner sensors will detect rearward objects.
USING THE PARKING AIDSwitching the parking aid on andoffNote: The parking aid switches offautomatically when you start the engine orwhen you exceed 16 km/h (10 mph).Note: The front and rear sensors are alwaysactivated or deactivated together.The parking aid is per default off. To switchthe parking aid on, press the switch in theinstrument panel or select reverse gear.The light in the switch illuminates whenthe parking aid is activated.To turn it off, press the switch again.
Manoeuvring with the parking aid
E72902
Note: If a high pitch warning tone soundsfor three seconds and the light in the switchis flashing, it indicates a malfunction. Thesystem will be disabled. Have the systemchecked by properly trained technicians.
114
Parking Aids
You will hear an intermittent tone at adistance of up to approximately 150centimetres (59 inches) between theobstacle and rear bumper, 80 centimetres(31 inches) between the obstacle and frontbumper and 50 centimetres (20 inches)to the side. Decreasing the distanceaccelerates the intermittent tone. Acontinuous tone will start at a distance ofless than 30 centimetres (12 inches).You will hear an alternating tone from thefront and rear if obstacles are closer than30 centimetres (12 inches) to the front andrear bumpers.
115
Parking Aids
PRINCIPLE OF OPERATIONThe camera is a visual aid for use whenreversing.
WARNINGThe system does not relieve you ofyour responsibility to drive with duecare and attention.
CAUTIONSIf you use a high pressure spray towash your vehicle, only spray thecamera briefly from a distance not
less than 20 centimetres (8 inches).Do not apply pressure to the camera.
Note: Keep the camera free from dirt, iceand snow. Do not clean with sharp objects,degreaser, wax or organic products. Use onlya soft cloth.During operation, guide lines appear in thedisplay which represent your vehicle's pathand approximate distance from rearwardobjects.
USING THE REAR VIEWCAMERA
WARNINGSThe operation of the camera mayvary depending on the ambienttemperature, vehicle and road
conditions.The distances shown in the displaymay differ from the actual distance.Do not place objects in front of thecamera.
The camera is located on the luggagecompartment lid near the handle.
E99105
Activating the rear view cameraCAUTION
The camera may not detect objectsthat are close to the vehicle.
With the ignition and the audio unitswitched on, engage reverse gear. Theimage is displayed on the screen.The camera may not operate correctly inthe following conditions:• Dark areas.• Intense light.• If the ambient temperature increases
or decreases rapidly.• If the camera is wet, for example in rain
or high humidity.• If the camera's view is obstructed, for
example by mud.
Using the displayCAUTIONS
Obstacles above the camera positionwill not be shown. Inspect the areabehind your vehicle if necessary.
116
Rear view camera
CAUTIONSMarks are for general guidance only,and are calculated for vehicles inmaximum load conditions on an even
road surface.
The lines show a projected vehicle path(based on the current steering wheelangle) and the distance from the exteriormirrors and rear bumper.
E99458
A
B
C
D E
A
B
C
D
Exterior mirror clearance - 0.1metre (4 inches)
A
Red - 0.3 metre (12 inches)BAmber - 1 metre (39 inches)C
117
Rear view camera
Amber - 2 metres (79 inches)DAmber - centre line of theprojected vehicle path
E
Note: When reversing with a trailer, the lineson the screen show the vehicle direction andnot the trailer.
Deactivating the rear view cameraNote: Disengage reverse gear. The displaywill stay on for a short period beforeswitching off.The system will automatically switch offonce the vehicle speed has reachedapproximately 15 km/h (9 mph).
Vehicles with parking aidThe display will additionally show acoloured distance bar. This guide indicatesthe distance from the rear bumper to thedetected obstacle.These are colour coded as follows:• Green - 0.8 to 1.5 metres (31 to 59
inches).• Amber - 0.3 to 0.8 metre (12 to 31
inches).• Red - 0.3 metre (12 inches) or less.
118
Rear view camera
PRINCIPLE OF OPERATION
WARNINGThe system does not relieve you ofyour responsibility to drive with duecare and attention.
Cruise control allows you to control yourspeed using the switches on the steeringwheel. You can use cruise control whenyou exceed approximately 30 km/h (20mph).
USING CRUISE CONTROL
WARNINGDo not use cruise control in heavytraffic, on twisty roads or when theroad surface is slippery.
Switching cruise control on
E75456
Note: The system is ready for you to set aspeed.
Setting a speed
E75452
Press to store and maintain your currentspeed. The cruise control indicator willilluminate. See Warning Lamps andIndicators (page 63).
Changing the set speedWARNING
When you are going downhill, yourspeed may increase above the setspeed. The system will not apply the
brakes. Change down a gear and press theSET- switch to assist the system inmaintaining the set speed.
Note: If you accelerate by pressing theaccelerator pedal, the set speed will notchange. When you release the acceleratorpedal, you will return to the speed that youpreviously set.
119
Cruise Control
E95393
A
B
AccelerateADecelerateB
Cancelling the set speed
E75453
Press the brake pedal or the RES switch.Note: The system will no longer controlyour speed. The cruise control indicator willnot illuminate but the system will retain thespeed that you previously set.
Resuming the set speed
E75453
The cruise control indicator will illuminateand the system will attempt to resume thespeed that you previously set.
Switching cruise control off
E75455
The system will not retain the speed thatyou previously set. The cruise controlindicator will not illuminate.
120
Cruise Control
GENERAL INFORMATION
WARNINGSUse load securing straps to anapproved standard, e.g. DIN.Make sure that you secure all looseitems properly.Place luggage and other loads as lowand as far forward as possible withinthe luggage or loadspace.Do not drive with the tailgate or reardoor open. Exhaust fumes may enterthe vehicle.Do not exceed the maximum frontand rear axle loads for your vehicle.See Vehicle identification (page
169).Heavy loads, when placed in thepassenger compartment, should beon folded rear seats as shown. See
Rear Seats (page 91).
CAUTIONSDo not allow items to contact the rearwindows.Do not use any abrasive materials toclean the interior of the rear windows.Do not install stickers or labels to theinterior of the rear windows.
E97377
LUGGAGE ANCHOR POINTS
E86913
LUGGAGE COVERS
WARNINGDo not place objects on the luggagecover.
121
Load Carrying
E112571
Pull out the cover until it locks.
E112572
Release it from the retaining points bypressing below the handle. Let it roll slowlyback into the case.
E112588
To remove or install the cover, push eitherend of the case inwards.
Stowing the luggage cover -vehicles with tyre repair kitSpace is provided under the luggagecompartment floor.
REAR UNDER FLOORSTORAGE
WARNINGWhen you are using a child seat witha support leg, make sure that youinstall the foam spacer correctly
inside the storage compartment and thatyou position the cover correctly.
122
Load Carrying
E78097
ROOF RACKS AND LOADCARRIERSRoof rack
WARNINGSIf you use a roof rack, the fuelconsumption of your vehicle will behigher and you may experience
different driving characteristics.Read and follow the manufacturer’sinstructions when you are fitting aroof rack.
CAUTIONDo not exceed the maximumpermissible roof load of 75 kilograms(165 pounds) (including the roof
rack).
Check the security of the roof rack andtighten its fittings as follows:• before starting• after driving 50 kilometres (30 miles)• at 1 000 kilometres (600 miles)
intervals.
Installing the crossbarsWARNING
Distribute the load evenly over theloading area and keep the centre ofgravity as low as possible. Secure the
load well to prevent it from slipping. Neverplace any loads directly onto the roofsurface.
CAUTIONRemove the crossbars before enteringan automatic car wash.
Note: The side mounting tracks aredesigned such that crossbars (for bicyclecarriers, ski carriers etc.) from the Fordaccessories range can be fitted.Note: Before installing the crossbars, cleanthe side mounting tracks with water and asponge.Note: Position the crossbars as shown.
A B
E98206
110 mmA700 mmB
123
Load Carrying
4 Nm21
E98207
1. Pull the handle out.2. Turn the handle clockwise to bring the
crossbar in contact with the rail.
3E98222
A
Note: Make sure there is no gap betweencrossbar and rail (A).3. Turn the handle a minimum of 3.5
revolutions.
E98208
4. Push the handle in. Turn the keyclockwise to lock.
5. Remove the key.
Accessing the T-notch
1
2
3
E98209
1. Pull the handle out.2. Lower the cover.3. Remove the sliding bar.
Cycle carrierCAUTION
The cycle carrier fixtures must only befitted to the main luggagecompartment lid.
124
Load Carrying
E99775
125
Load Carrying
TOWING A TRAILER
WARNINGSDo not exceed the maximum grosstrain weight stated on the vehicleidentification plate. See Vehicle
identification (page 169).Do not exceed 100 km/h (62 mph).
The rear tyre pressures must beincreased by 0.2 bar (3 psi) abovespecification. See Technical
Specifications (page 166).
CAUTIONSDo not exceed the maximumpermissible nose weight, i.e. verticalweight on the tow ball, of 100
kilogrammes (220 pounds) for vehicleswith a diesel engine, or 105 kilogrammes(231 pounds) for vehicles with a petrolengine.
We recommend you purchase atowing kit from your dealer. Failure todo so may result in damage to the
engine.
Note: Not all vehicles are suitable orapproved to have tow bars fitted. Checkwith your dealer first.Place loads as low and central to theaxle(s) of the trailer as possible. If you aretowing with an unladen vehicle, the loadin the trailer should be placed toward thenose, within the maximum nose load, asthis gives the best stability.The stability of the vehicle to trailercombination is very much dependant onthe quality of the trailer.
In high altitude regions above 1 000 metres(3 281 feet), the stipulated maximumpermitted gross train weight must bereduced by 10% for every additional 1 000metres (3 281 feet).
Steep gradientsWARNING
The overrun brake on a trailer is notcontrolled by ABS.
Change down a gear before you reach asteep downhill gradient.
TOW BALL
WARNINGSWhen not in use, always transportthe tow ball arm securely fastenedin the luggage compartment.Take special care when fitting thetow ball arm as the safety of thevehicle and the trailer depends on
this.Do not use any tools for mounting ordismounting the tow ball arm. Do notmodify the trailer coupling. Do not
disassemble or repair the tow ball arm.
E71328
126
Towing
Unlocking the tow ball armmechanism
E99477
1
2
1. Detach the keyhole protective cap.2. Insert the key and turn it anti-clockwise
to unlock (1).3. Hold the tow ball arm. Pull the
handwheel out and turn it clockwiseuntil it clicks (2).
4. The red mark on the handwheel mustalign with the white mark on the towball.
5. Release the handwheel. The tow ballarm is unlocked.
Inserting the tow ball armWARNING
The tow ball arm may only beinserted when completely unlocked.
E99484
1
3
2
1. Pull out the plug (1).2. Insert the tow ball arm vertically and
press it upwards until it engages (2).Do not hold your hand near thehandwheel.
3. The green mark on the handwheelmust align with the white dot on thetow ball.
4. To lock, turn the key clockwise andremove the key (3).
5. Attach the keyhole protective cap.
127
Towing
Driving with a trailer
E71331
A
B
WARNINGIf any of the below conditions cannotbe met, do not use the tow bar andhave it checked by a properly trained
technician.
Before starting your journey, make surethat the tow ball arm is properly locked.Check:• The green mark on the handwheel is
aligned with the white dot on the towball arm.
• the handwheel (A) is correctly fittedto the tow ball arm.
• you have removed the key (B).• the tow ball arm is securely positioned.
It must not move when jerked.
Removing the tow ball armWARNING
Never unlock the tow ball arm withthe trailer attached.
E99485
4
1
3
2
1. Unhitch the trailer.2. Detach the keyhole protective cap.3. Insert the key and turn it anti-clockwise
to unlock (1).4. Hold the tow ball arm. Pull the
handwheel out, turn it clockwiseagainst the stop (2) and remove thetow ball arm (3).
5. Release the handwheel.When unlocked in this way, the tow ballarm can be reinserted at any time.Insert the plug into its seat (4).
MaintenanceWARNING
Remove the tow ball arm andprotect the seat with the plug beforesteam cleaning your vehicle.
128
Towing
Keep the system clean. Periodicallylubricate bearings, sliding surfaces, andlocking balls with resin-free grease or oiland the lock with graphite.Keep a note of the key number. In case ofloss, replacement keys are available fromthe manufacturer by stating the three digitkey number.
129
Towing
RUNNING-INTyres
WARNINGNew tyres need to be run-in forapproximately 500 kilometres (300miles). During this time, you may
experience different driving characteristics.
Brakes and clutchWARNING
Avoid heavy use of the brakes andclutch if possible for the first 150kilometres (100 miles) in town and
for the first 1500 kilometres (1000 miles)on motorways.
EngineCAUTION
Avoid driving too fast during the first1500 kilometres (1000 miles). Varyyour speed frequently and change up
through the gears early. Do not labour theengine.
COLD WEATHERPRECAUTIONSThe functional operation of somecomponents and systems can be affectedat temperatures below -30°C (-22°F).
DRIVING THROUGH WATERDriving through water
CAUTIONSDrive through water in an emergencyonly, and not as part of normal driving.Engine damage can occur if waterenters the air filter.
In an emergency, the vehicle can be driventhrough water to a maximum depth of 200millimetres (8 inches) and at a maximumspeed of 10 km/h (6 mph). Extra cautionshould be exercised when driving throughflowing water.When driving in water, maintain a lowspeed and do not stop the vehicle. Afterdriving through water, and as soon as it issafe to do so:• Depress the brake pedal lightly and
check that full brake function isachieved.
• Check that the horn works.• Check that the vehicle's lights are fully
operational.• Check the power assistance
of the steering system.
130
Driving Hints
FIRST AID KITSpace is provided in the under floor storagecompartment. See Rear Under FloorStorage (page 122).
WARNING TRIANGLESpace is provided in the under floor storagecompartment. See Rear Under FloorStorage (page 122).
131
Roadside Emergencies
FUEL CUT-OFF SWITCHVehicles with a Duratec engine
E72531
The fuel supply may be cut off as a resultof an accident or sudden vibrations (e.g.collision when parking).The switch is located in the side panel infront of the driver's door.
Resetting the switch
WARNINGDo not reset the fuel cut-off switchif you see or smell leaking fuel.
• Turn the ignition switch to position 0.• Check fuel system for leaks.• If no fuel leak is apparent, reset the
switch by pushing in the button (seeillustration).
• Turn the ignition switch to position II.After a few seconds return the key toposition I.
• Make a further check for leaks in thefuel system.
132
Status after a collision
FUSE BOX LOCATIONSEngine compartment fuse box
E78332
Passenger compartment fuse box1. Remove the screws in the instrument
panel trim underneath the glovecompartment and lower the trim panel.
2. Loosen the screws.3. Lower the fuse box and pull it towards
you.
Install in the reverse order.
CHANGING A FUSE
WARNINGSDo not modify the electrical systemof your vehicle in any way. Haverepairs to the electrical system and
the replacement of relays and high currentfuses carried out by properly trainedtechnicians.
Switch the ignition and all electricalequipment off before touching orattempting to change a fuse.
CAUTIONFit a replacement fuse with the samerating as the one you have removed.
Note: You can identify a blown fuse by abreak in the filament.Note: All fuses, except high current fusesare a push fit.Note: A fuse puller is located in the lid ofthe engine compartment fuse box.
133
Fuses
FUSE SPECIFICATION CHARTEngine compartment fuse box
E79716
19
6
7 8
10
9
12
11
14
13
16
15
29 36
28
34
35
33
22 25 325
4
3
2
1
2017
18
2421 30 31
23 26 27Circuits protectedAmpere
ratingFuse
Cooling fan401
Power steering802
Passenger junction box supply 1603
Passenger junction box supply 2604
PTC heater805
Glow plugs (diesel only)606
ESP pump307
ESP valves208
Powertrain control module209
Climate control blower3010
Ignition switch2011
134
Fuses
Circuits protectedAmpereratingFuse
Ignition relay 15l4012
Starter solenoid2013
Heated windscreen, right-hand side4014
Not used-15
Heated windscreen, left-hand side4016
Not used-17
Power converter3018
ESP module1019
Horn1520
Auxiliary heater2021
Power steering module1022
Headlamp washer3023
Diesel fuel heater1524
Ignition, relays1025
Automatic transmission1526
Air conditioning clutch1027
Glow plug monitoring (diesel only)1028
Dual zone climate control1029
Powertrain control module330
Battery sensor smart charging1031
Injectors (petrol only)1032
Heated oxygen sensors (petrol only)1033
Ignition coils, valves1034
Powertrain control module, valves, solenoids1035
Powertrain control module1036
135
Fuses
Passenger compartment fuse box
100
101102
103
104
138139
140
141142
143
105
111
117
123
130
132
133
129
134
135
136
137
131
106
112
118
124
109
115
121
127
110
116
122
128
107
113
119
125
108
114
120
126
E88709
Circuits protectedAmpere ratingFuse
Electronic modules ignitionsupply10100
Driver’s electric seat20101
Heater control, remotecontrol receiver10102
Lighting control batterysupply10103
Battery saver, interior lamps10104
Heated rear window25105
Keyless start20106
Instrument cluster batterysupply, on-boarddiagnostics
10107
Accessory to cluster (audioand navigation unit)7.5108
Cigar lighter, rear auxiliarypower socket20109
136
Fuses
Circuits protectedAmpere ratingFuse
Daytime running lamps igni-tion supply to lightingcontrol switch
10110
Fuel pump (diesel only)5111
Fuel pump (petrol only)15111
Audio modules batterysupply15112
Daytime running lamps(parking lamps)10113
Instrument cluster ignitionsupply, engine immobiliser10114
Lighting control ignitionsupply7.5115
Fog lamps20116
Number plate lamps7.5117
Door module, left-hand rear20118
Luggage compartmentauxiliary power socket15119
Luggage compartmentauxiliary power socket(vehicles with trailer towmodule)
25119
Door module, right-handrear20120
Heated front seats20121
Airbag module10122
Heated exterior mirrors7.5123
Parking lamps, side lamps,tail lamps (left-hand side)7.5124
Parking lamps, side lamps,tail lamps (right-hand side)7.5125
Key free system20126
137
Fuses
Circuits protectedAmpere ratingFuse
Not used-127
Not used-128
Windscreen wipers20129
AWD module10130
Rear window wiper15131
Brake lamps15132
Central locking relays,passenger door module25133
Central locking relays, driverdoor module20134
Daytime running lamps20135
Washer pump, heatedwasher jets15136
Battery backup sounder10137
Powertrain control module,accelerator pedal, auto-matic transmission, keylessmodule IGN monitor
10138
Main beam right-hand side10139
Main beam left-hand side10140
Reversing lamp10141
Dipped beam, right-handside15142
Dipped beam, left-hand side15143
138
Fuses
TOWING POINTSFront towing eye
E99490
Rear towing eye
E99491
Note: On vehicles with a tow bar, thetowing eye cannot be installed at the rearof the vehicle. Use the tow bar to tow avehicle.
Towing eye location
E99468
The screw-in towing eye is located in theluggage compartment next to the sparewheel well.The towing eye must always be carried inthe vehicle.Prise off the cover and install the towingeye.
CAUTIONThe screw-in towing eye has aleft-hand thread. Turn itanti-clockwise to install it. Make sure
that the towing eye is fully tightened.
TOWING THE VEHICLE ONFOUR WHEELSAll vehicles
WARNINGSSwitch the ignition on when yourvehicle is being towed. The steeringlock will engage and the direction
indicators and brake lamps will not workif you do not.
139
Vehicle recovery
WARNINGSThe brake servo and the powersteering pump do not operate unlessthe engine is running. Press the brake
pedal harder and allow for increasedstopping distances and heavier steering.
CAUTIONSToo much tension in the tow ropecould cause damage to your vehicleor the vehicle that is towing.Do not use a rigid tow bar on the fronttowing eye.Select neutral when your vehicle isbeing towed.For vehicles with AWD, in the event ofa breakdown or mechanical failure ofthe transmission your vehicle must be
recovered with either ALL wheels on theground or transported with ALL wheels offthe ground.
Drive off slowly and smoothly withoutjerking the vehicle that is towing.
Vehicles with automatictransmission
CAUTIONSIf a speed of 20 km/h (12 mph) and adistance of 20 kilometres (12 miles)is to be exceeded the drive wheels
must be lifted clear of the ground.It is recommended not to tow with thedrive wheels on the ground. However,if it is required to move the vehicle
from a dangerous location, do not tow yourvehicle faster than 20 km/h (12 mph) orfurther than 20 kilometres (12 miles).
Do not tow your vehicle backwards.
In the event of a mechanical failure ofthe transmission the drive wheelsmust be lifted clear of the ground.
CAUTIONSDo not tow your vehicle if the ambienttemperature is below 0ºC (32ºF).
140
Vehicle recovery
GENERAL INFORMATIONHave your vehicle serviced regularly to helpmaintain its roadworthiness and resalevalue. There is a large network of FordAuthorised Repairers that are there to helpyou with their professional servicingexpertise. We believe that their speciallytrained technicians are best qualified toservice your vehicle properly and expertly.They are supported by a wide range ofhighly specialised tools developedspecifically for servicing your vehicle.In addition to regular servicing, werecommend that you carry out thefollowing additional checks.
WARNINGSSwitch the ignition off beforetouching or attempting adjustmentof any kind.Do not touch the electronic ignitionsystem parts after you have switchedthe ignition on or when the engine is
running. The system operates at highvoltage.
Keep your hands and clothing clearof the engine cooling fan. Undercertain conditions, the fan may
continue to run for several minutes afteryou have switched the engine off.
CAUTIONWhen carrying out maintenancechecks, make sure that filler caps arefitted securely.
Daily checks• Exterior lamps.• Interior lamps.• Warning lamps and indicators.
Check when refuelling• Engine oil level. See Engine Oil Check
(page 146).• Brake fluid level. See Brake and
Clutch Fluid Check (page 147).• Washer fluid level. See Washer Fluid
Check (page 148).• Tyre pressures (when cold). See
Technical Specifications (page 166).• Tyre condition. See Tyre Care (page
165).
Monthly checks• Engine coolant level (engine cold). See
Engine Coolant Check (page 147).• Pipes, hoses and reservoirs for leaks.• Power steering fluid level. See Power
Steering Fluid Check (page 148).• Air conditioning operation.• Parking brake operation.• Horn operation.• Tightness of wheel nuts. See
Technical Specifications (page 166).
OPENING AND CLOSING THEBONNETOpening the bonnet
WARNINGTo prevent damage to, or loss of thekey, remove the key immediatelyafter opening and swivel the Ford
badge back.
Note: On vehicles with keyless entry, usethe spare key. See Keyless Entry (page32).
141
Maintenance
1
E78141
E78142
2 3
5
4
E78143
Closing the bonnetNote: Make sure that the bonnet is closedproperly.Lower the bonnet and allow it to drop fromunder its own weight for the last 20 – 30centimetres (8 - 12 inches).
142
Maintenance
UNDER BONNET OVERVIEW - 2.5L DURATEC (VI5)
E78890
I
FEDCBA
H G
Screen washer fluid reservoir*: See Washer Fluid Check (page 148).AEngine coolant reservoir*: See Engine Coolant Check (page 147).BBrake and clutch fluid reservoir (right-hand drive)*: See Brake and ClutchFluid Check (page 147).
C
Engine oil filler cap*: See Engine Oil Check (page 146).DBrake and clutch fluid reservoir (left-hand drive)*: See Brake and Clutch FluidCheck (page 147).
E
Battery: See Vehicle battery (page 153).F
143
Maintenance
Engine compartment fuse box: See Fuses (page 133).GAir cleaner: No maintenance necessary.HEngine oil dipstick*: See Engine Oil Check (page 146).I
*For easy identification, filler caps and the engine oil dipstick are marked in colour.
UNDER BONNET OVERVIEW - 2.0L DURATORQ-TDCI (DW) DIESEL
E78893
I
FEDCBA
H G
144
Maintenance
I
FEDCBA
H GE125377
Screen washer fluid reservoir*: See Washer Fluid Check (page 148).AEngine coolant reservoir*: See Engine Coolant Check (page 147).BBrake and clutch fluid reservoir (right-hand drive)*: See Brake and ClutchFluid Check (page 147).
C
Engine oil filler cap*: See Engine Oil Check (page 146).DBrake and clutch fluid reservoir (left-hand drive)*: See Brake and Clutch FluidCheck (page 147).
E
Battery: See Vehicle battery (page 153).FEngine compartment fuse box: See Fuses (page 133).G
145
Maintenance
Air cleaner: No maintenance necessary.HEngine oil dipstick*: See Engine Oil Check (page 146).I
*For easy identification, filler caps and the engine oil dipstick are marked in colour.
ENGINE OIL DIPSTICK - 2.5LDURATEC (VI5)
E95542
BA
MINAMAXB
ENGINE OIL DIPSTICK - 2.0LDURATORQ-TDCI (DW) DIESEL
E95543
BA
MINAMAXB
ENGINE OIL CHECK
CAUTIONDo not use oil additives or otherengine treatments. Under certainconditions, they could damage the
engine.
Note: The oil consumption of new enginesreaches its normal level after approximately5000 kilometres (3000 miles).
Checking the oil levelCAUTION
Make sure that the level is betweenthe MIN and the MAX marks.
Note: Check the level before starting theengine.Note: Make sure that your vehicle is on levelground.Note: Oil expands when it is hot. The levelmay therefore extend a few millimetresbeyond the MAX mark.Remove the dipstick and wipe it with aclean, lint free cloth. Replace the dipstickand remove it again to check the oil level.If the level is at the MIN mark, top upimmediately.
Topping upWARNINGS
Only top up when the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.
146
Maintenance
WARNINGSDo not remove the filler cap whenthe engine is running.
Remove the filler cap.CAUTION
Do not top up further than the MAXmark.
Top up with fluid that meets the Fordspecification. See TechnicalSpecifications (page 149).Replace the filler cap. Turn it until you feela strong resistance.
ENGINE COOLANT CHECKChecking the coolant level
WARNINGDo not allow the fluid to touch yourskin or eyes. If this happens, rinse theaffected areas immediately with
plenty of water and contact your doctor.
CAUTIONMake sure that the level is betweenthe MIN and the MAX marks.
Note: Coolant expands when it is hot. Thelevel may therefore extend beyond the MAXmark.If the level is at the MIN mark, top upimmediately.
Topping upWARNINGS
Only top up when the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.
WARNINGSDo not remove the filler cap whenthe engine is running.Do not remove the filler cap whenthe engine is hot. Wait for the engineto cool down.Undiluted coolant is flammable andmay ignite if spilt on a hot exhaust.
CAUTIONSIn an emergency, you can add justwater to the cooling system to reacha vehicle service station. Have the
system checked by a properly trainedtechnician as soon as possible.
Prolonged use of incorrect dilution ofthe coolant can cause engine damagefrom corrosion, overheating or
freezing.
Unscrew the cap slowly. Any pressure willescape slowly as you unscrew the cap.
CAUTIONDo not top up further than the MAXmark.
Top up with a 50/50 mixture of coolantand water using fluid that meets the Fordspecification. See TechnicalSpecifications (page 149).
BRAKE AND CLUTCH FLUIDCHECK
WARNINGSUse of any fluid other than therecommended brake fluid mayreduce brake efficiency and not meet
Ford's performance standards.
147
Maintenance
WARNINGSDo not allow the fluid to touch yourskin or eyes. If this happens, rinse theaffected areas immediately with
plenty of water and contact your doctor.If the level is at the MIN mark, havethe system checked by a properlytrained technician as soon as
possible.
Note: Keep brake fluid clean and dry.Contamination with dirt, water, petroleumproducts or other materials may result inbrake system damage and possible failure.Note: The brake and the clutch systems aresupplied from the same reservoir.Top up with fluid that meets the Fordspecification. See TechnicalSpecifications (page 149).
POWER STEERING FLUIDCHECK
WARNINGDo not allow the fluid to touch yourskin or eyes. If this happens, rinse theaffected areas immediately with
plenty of water and contact your doctor.
CAUTIONMake sure that the level is betweenthe MIN and the MAX marks.
If the level is at the MIN mark, top upimmediately.
Topping upRemove the filler cap.
CAUTIONDo not top up further than the MAXmark.
Top up with fluid that meets the Fordspecification. See TechnicalSpecifications (page 149).
WASHER FLUID CHECKNote: The front and rear washer systemsare supplied from the same reservoir.When topping up, use a mixture of washerfluid and water to help prevent freezing incold weather and improve the cleaningcapability. We recommend that you useonly high quality washer fluid.For information on fluid dilution, refer tothe product instructions.
148
Maintenance
TECHNICAL SPECIFICATIONSVehicle fluids
Recommended fluidSpecificationItem
Castrol Engine Oil*WSS-M2C913-CEngine oil
Ford or Motorcraft PowerSteering FluidWSS-M2C204-A2Power steering fluid
Motorcraft SuperPlus Anti-freezeWSS-M97B44-DCoolant
Motorcraft or Ford DOT 4 LVHigh Performance Brake
FluidWSS-M6C65-A2 or ISO4925 Class 6Brake fluid
* Providing it meets the specification defined by WSS-M2C913-C, you can also use FordEngine Oil or an alternative engine oil.Note: If you operate your vehicle in temperatures below -20°C (-4°F), you must not useSAE 10W-40 engine oil.Topping up the oil: If you are unable to find an oil that meets the specification definedby WSS-M2C913-C, you must use SAE 5W-30 (preferred), SAE 5W-40 or SAE 10W-40that meets the specification defined by either ACEA A1/B1 (preferred) or ACEA A3/B3.Using these oils can result in longer engine cranking periods, reduced engine performance,reduced fuel economy and increased emission levels.Castrol engine oil recommended.
E115472
Capacities
Capacity in Litres (gallons)ItemVariant
MAX markPower assisted steeringfluidAll
approx. 8.6 (1.9)Engine cooling systemAll
4.0 (0.9)Windscreen washer systemAll
65 (14.3)Fuel tank2.0L Duratorq-TDCi (DW)
66 (14.5)Fuel tank2.5L Duratec (VI5)
149
Maintenance
Capacity in Litres (gallons)ItemVariant
5.5 (1.2)Engine oil - with filter2.0L Duratorq-TDCi (DW)
5.0 (1.1)Engine oil - without filter2.0L Duratorq-TDCi (DW)
5.8 (1.3)Engine oil - with filter2.5L Duratec (VI5)
5.5 (1.2)Engine oil - without filter2.5L Duratec (VI5)
150
Maintenance
CLEANING THE EXTERIOR
WARNINGIf you use a car wash with a waxingcycle, make sure that you remove thewax from the windscreen.
CAUTIONSPrior to using a car wash facility checkthe suitability of it for your vehicle.Some car wash installations usewater at high pressure. This coulddamage certain parts of your vehicle.Remove the aerial before using anautomatic car wash.Switch the heater blower off toprevent contamination of the fresh airfilter.
We recommend that you wash your vehiclewith a sponge and lukewarm watercontaining a car shampoo.
Cleaning the headlampsCAUTIONS
Do not scrape the headlamp lensesor use abrasives, alcoholic solvents orchemical solvents to clean them.Do not wipe the headlamps whenthey are dry.
Cleaning the rear windowCAUTION
Do not scrape the inside of the rearwindow or use abrasives or chemicalsolvents to clean it.
Use a clean, lint free cloth or a dampchamois leather to clean the inside of therear window.
Cleaning the chrome trimCAUTION
Do not use abrasives or chemicalsolvents. Use soapy water.
Body paintwork preservationCAUTIONS
Do not polish your vehicle in strongsunshine.Do not allow polish to touch plasticsurfaces. It could be difficult toremove.Do not apply polish to the windscreenor rear window. This could cause thewipers to become noisy and they may
not clear the window properly.
We recommend that you wax thepaintwork once or twice a year.
CLEANING THE INTERIORSeat belts
WARNINGSDo not use abrasives, or chemicalsolvents to clean them.Do not allow moisture to penetratethe seat belt retractor mechanism.
Clean the seat belts with interior cleaneror water applied with a soft sponge. Letthe seat belts dry naturally, away fromartificial heat.
151
Vehicle Care
Instrument cluster screens, LCDscreens, radio screens
WARNINGDo not use abrasives, alcoholicsolvents or chemical solvents toclean them.
Rear windowsCAUTIONS
Do not use any abrasive materials toclean the interior of the rear windows.Do not install stickers or labels to theinterior of the rear windows.
REPAIRING MINOR PAINTDAMAGE
CAUTIONRemove apparently harmless lookingsubstances from the paintworkimmediately (e.g. bird droppings, tree
resins, insect remains, tar spots, road saltand industrial fall out).
You should repair paintwork damagecaused by stones from the road or minorscratches as soon as possible. A choice ofproducts is available from your FordDealer. Read and follow themanufacturer’s instructions.
152
Vehicle Care
JUMP-STARTING THE VEHICLE
CAUTIONSConnect batteries with only the samenominal voltage.Always use booster cables withinsulated clamps and adequate sizecable.Do not disconnect the battery fromthe vehicle’s electrical system.
To connect the booster cables
A
B
C D
E99387
Flat battery vehicleABooster battery vehicleBPositive connection cableCNegative connection cableD
153
Vehicle battery
1. Position the vehicles so that they donot touch one another.
2. Switch off the engine and any electricalequipment.
3. Connect the positive (+) terminal ofvehicle B with the positive (+) terminalof vehicle A (cable C).
4. Connect the negative (-) terminal ofvehicle B to the ground connection onthe left-hand side suspension turret ofvehicle A (cable D).
CAUTIONSDo not connect to the negative (–)terminal of the flat battery.Make sure that the cables are clear ofany moving parts.
To start the engine1. Run the engine of vehicle B at
moderately high speed.2. Start the engine of vehicle A.3. Run both vehicles for a minimum of
three minutes before disconnecting thecables.
CAUTIONDo not switch on the headlamps whendisconnecting the cables. The peakvoltage could blow the bulbs.
Disconnect the cables in the reverse order.
154
Vehicle battery
GENERAL INFORMATION
CAUTIONSUse only approved wheel and tyresizes. Using other sizes could damagethe vehicle and will make the National
Type Approval invalid.If you change the diameter of the tyresfrom that fitted at the factory, thespeedometer may not display the
correct speed. Take the vehicle to yourdealer to have the engine managementsystem reprogrammed.
If you intend to change the size of thewheels from that fitted at the factory,check the suitability with your dealer.
Note: Check your tyre pressures regularlyto optimise fuel economy.A decal with tyre pressure data is locatedin the driver’s door opening at the B-pillar.Check and set the tyre pressure at theambient temperature in which you areintending to drive the vehicle and when thetyres are cold.
CHANGING A ROAD WHEELLocking wheel nutsYou can obtain a replacement lockingwheel nut key and replacement lockingwheel nuts from your dealer using thereference number certificate.
Vehicles with a temporary sparewheel
WARNINGSIf the spare wheel differs from theother fitted wheels, these rules mustbe followed:Do not exceed 80 km/h (50 mph).
WARNINGSDrive the shortest possible distances.
Do not fit more than one spare wheelon your vehicle at any one time.Do not use snow chains on this typeof wheel.Do not drive through an automaticcar wash.Do not carry out any tyre repairs ona temporary spare wheel.
CAUTIONThe ground clearance of your vehiclewill be reduced. Take care whenparking next to a kerb.
Note: Your vehicle may exhibit someunusual driving characteristics.
Vehicle jackWARNINGS
The vehicle jack supplied with yourvehicle should only be used whenchanging a wheel in emergency
situations.Before using the vehicle jack, checkthat it is not damaged or deformedand that the thread is lubricated and
free from foreign matter.Never place anything between thejack and the ground, or the jack andthe vehicle.
Note: Vehicles with a tyre repair kit or runflat tyres are not equipped with a vehiclejack or a wheel brace.It is recommended to use a workshop typehydraulic jack for changing betweensummer and winter tyres.
155
Wheels and Tyres
Note: Use a jack with a minimum liftingcapacity of 1.5 tonnes and a lifting plate witha minimum diameter of 80 millimetres (3.1inches).
Vehicles without tyre repair kit or runflat tyresYour vehicle jack, wheel brace, screw-intowing eye and wheel trim remover arelocated in the spare wheel well.
Jacking and lifting pointsCAUTION
Use only the specified jacking points.If you use other positions, you maydamage the body, steering,
suspension, engine, braking system or thefuel lines.
E92658
A
B
Emergency use onlyAMaintenanceB
156
Wheels and Tyres
E93184
A
Indentations in the sills A show thelocation of the jacking points.
E92932
E93020
Vehicles with side skirts
E95345
Assembling the wheel braceType one
WARNINGWhen returning the wheel braceextension to its original position, takecare not to get your fingers caught.
Note: Make sure that the wheel brace isfully extended.
E122546
Extend the wheel brace.
Type two
CAUTIONThe screw-in towing eye has aleft-hand thread. Turn itanti-clockwise to install it. Make sure
that the towing eye is fully tightened.
157
Wheels and Tyres
E122502
Insert the screw-in towing eye into thewheel brace.
Removing the wheel trimType oneInsert the flat end of the wheel bracebetween the rim and the trim and carefullyremove the trim.
Type two
E122314
2
1
1. Insert the wheel trim remover.2. Remove the wheel trim.Note: Make sure that you pull the wheeltrim remover at right angles to the trim.
Removing a road wheelWARNINGS
Park your vehicle in such a positionthat neither the traffic nor you arehindered or endangered.Set up a warning triangle.
Make sure that the vehicle is on firm,level ground with the wheels pointingstraight ahead.Switch off the ignition and apply theparking brake.If your vehicle has a manualtransmission, select first or reversegear. If it has an automatic
transmission, select park.Have the passengers leave thevehicle.Secure the diagonally oppositewheel with an appropriate block orwheel chock.Make sure that the arrows ondirectional tyres point in the directionof rotation when the vehicle is
moving forwards. If you have to fit a sparewheel with the arrows pointing in theopposite direction, have the tyre refittedin the correct direction by a properlytrained technician.
Do not work underneath the vehiclewhen it is supported only by a jack.Make sure that the jack is vertical tothe jacking point and the base is flaton the ground.
CAUTIONDo not lay alloy wheels face down onthe ground, this will damage the paint.
Note: The spare wheel is located under thefloor cover in the luggage compartment.
158
Wheels and Tyres
1. Install the locking wheel nut key.
E121887
1
2
2. Slacken the wheel nuts.3. Jack up the vehicle until the tyre is clear
of the ground.4. Remove the wheel nuts and the wheel.
Installing a road wheelWARNINGS
Use only approved wheel and tyresizes. Using other sizes coulddamage the vehicle and will make
the National Type Approval invalid. SeeTechnical Specifications (page 166).
Do not fit run flat tyres on vehiclesthat were not originally fitted withthem. Please contact your dealer for
more details regarding compatibility.
CAUTIONDo not install alloy wheels usingwheel nuts designed for use with steelwheels.
Note: Make sure the wheel and hub contactsurfaces are free from foreign matter.Note: Make sure that the cones on thewheel nuts are against the wheel.1. Install the wheel.2. Install the wheel nuts finger tight.3. Install the locking wheel nut key.
1
2
3 4
5
E75442
4. Partially tighten the wheel nuts in thesequence shown.
5. Lower the vehicle and remove the jack.6. Fully tighten the wheel nuts in the
sequence shown. See TechnicalSpecifications (page 166).
7. Install the wheel trim using the ball ofyour hand.
WARNINGHave the wheel nuts checked fortightness and the tyre pressurechecked as soon as possible.
159
Wheels and Tyres
TYRE REPAIR KITYour vehicle is not equipped with a sparetyre, but does include an emergency tyrerepair kit that can be used to repair oneflat tyre.The tyre repair kit is located in theunderfloor storage compartment. SeeStorage compartments (page 95).Note: Remove the underfloor storagecompartment screws if fitted.
General informationWARNINGS
Depending on the type and extent oftyre damage, some tyres can only bepartially sealed or not sealed at all.
Loss of tyre pressure can affect vehiclehandling, leading to loss of vehicle control.
Do not use the tyre repair kit if thetyre has already been damaged as aresult of being driven under inflated.Do not use the tyre repair kit on runflat tyres.Do not try to seal damage other thanthat located within the visible treadof the tyre.Do not try to seal damage to thetyre’s sidewall.
The tyre repair kit seals most tyrepunctures [with a diameter of up to sixmillimetres (1/4 inch)] to temporarilyrestore mobility.Observe the following rules when using thekit:
• Drive with caution and avoidmaking sudden steering or drivingmanoeuvres, especially if the vehicleis heavily loaded or you are towing atrailer.
• The kit will provide you with anemergency temporary repair, enablingyou to continue your journey to the nextvehicle or tyre dealer, or to drive amaximum distance of 200 kilometres(125 miles).
• Do not exceed a maximum speed of80 km/h (50 mph).
• Keep the kit out of the reach ofchildren.
• Only use the kit when the ambienttemperature is between –30°C (-22°F)and +70°C (+158°F).
Using the tyre repair kitWARNINGS
Compressed air can act as anexplosive or propellant.Never leave the tyre repair kitunattended while in use.
CAUTIONDo not keep the compressor operatingfor more than 10 minutes.
Note: Use the tyre repair kit only for thevehicle with which it was supplied.• Park your vehicle at the roadside so
that you do not obstruct the flow oftraffic and so that you are able to usethe kit without being in danger.
• Apply the parking brake, even if youhave parked on a level road, to makesure that the vehicle will not move.
• Do not attempt to remove foreignobjects like nails or screws penetratingthe tyre.
160
Wheels and Tyres
• Leave the engine running while the kitis in use, but not if the vehicle is in anenclosed or poorly ventilated area (forexample, inside a building). In thesecircumstances, switch the compressoron with the engine turned off.
• Replace the sealant bottle with a newone before the expiry date (see top ofbottle) is reached.
• Inform all other users of the vehiclethat the tyre has been temporarilysealed with the tyre repair kit and makethem aware of the special drivingconditions to be observed.
Inflating the tyreWARNINGS
Check the sidewall of the tyre priorto inflation. If there are any cracks,bumps or similar damage, do not
attempt to inflate the tyre.Do not stand directly beside the tyrewhile the compressor is pumping.Watch the sidewall of the tyre. If anycracks, bumps or similar damageappear, turn off the compressor and
let the air out by means of the pressurerelief valve B. Do not continue driving withthis tyre.
The sealant contains natural rubberlatex. Avoid contact with skin andclothing. If this happens, rinse the
affected areas immediately with plenty ofwater and contact your doctor.
If the tyre inflation pressure does notreach 1.8 bar (26 psi) within sevenminutes, the tyre may have suffered
excessive damage, making a temporaryrepair impossible. In this case, do notcontinue driving with this tyre.
CAUTIONScrewing the bottle onto the bottleholder will pierce the seal of thebottle. Do not unscrew the bottle from
the holder as the sealant will escape.
E94973
BJ
I
FE
C
KA
G
H
D
Protective capAPressure relief valveBHoseCOrange capDBottle holderEPressure gaugeF
161
Wheels and Tyres
Power plug with cableGCompressor switchHLabelIBottle lidJSealant bottleK
1. Open the lid of the tyre repair kit.2. Peel off the label I showing the
maximum permissible speed of80 km/h (50 mph) from the casing andattach it to the instrument panel in thedriver’s field of view. Make sure thelabel does not obscure anythingimportant.
3. Take the hose C and the power plugwith cable G out of the kit.
4. Unscrew the orange cap D and thebottle lid J.
5. Screw the sealant bottle K clockwiseinto the bottle holder E fully tight.
6. Remove the valve cap from thedamaged tyre.
7. Detach the protective cap A from thehose C and screw the hose C firmlyonto the valve of the damaged tyre.
8. Make sure that the compressor switchH is in position 0.
9. Insert the power plug G into the cigarlighter socket or auxiliary power socket.See Cigar Lighter (page 94). SeeAuxiliary Power Points (page 94).
10. Start the engine.11. Move the compressor switch H to
position 1.12. Inflate the tyre for no longer than
seven minutes to an inflation pressureof minimum 1.8 bar (26 psi) and amaximum of 3.5 bar (51 psi). Movethe compressor switch H to position0 and check the current tyre pressurewith pressure gauge F.
13. Remove the power plug G from thecigar lighter socket or auxiliary powersocket.
14. Quickly unscrew the hose C from thetyre valve and replace the protectivecap A. Fasten the valve cap again.
15. Leave the sealant bottle K in thebottle holder E.
16. Make sure the kit, the bottle lid andthe orange cap are stored safely, butstill easily accessible in the vehicle.The kit will be required again whenyou check the tyre pressure.
17. Immediately drive approximatelythree kilometres (two miles) so thatthe sealant can seal the damagedarea.
Note: When pumping in the sealant throughthe tyre valve, the pressure may rise up to6 bar (87 psi) but will drop again after about30 seconds.
WARNINGIf you experience heavy vibrations,unsteady steering behaviour ornoises while driving, reduce your
speed and drive with caution to a placewhere it is safe for you to stop the vehicle.Recheck the tyre and its pressure. If thetyre pressure is less than 1.3 bar (19 psi) orif there are any cracks, bumps or similardamage visible, do not continue drivingwith this tyre.
Checking the tyre pressure1. Stop the vehicle after driving
approximately three kilometres(two miles). Check, and wherenecessary, adjust the pressure of thedamaged tyre.
2. Attach the kit and read the tyrepressure from the pressure gauge F.
162
Wheels and Tyres
3. If the pressure of the sealant-filled tyreis 1.3 bar (19 psi) or more, adjust it tothe specified pressure. See TechnicalSpecifications (page 166).
4. Follow the inflation procedure onceagain to top up the tyre.
5. Check the tyre pressure again from thepressure gauge F. If the tyre pressureis too high, deflate the tyre to thespecified pressure using the pressurerelief valve B.
6. Once you have inflated the tyre to itscorrect tyre pressure, move thecompressor switch H to position 0,remove the power plug G from thesocket, unscrew the hose C, fasten thevalve cap and replace the protectivecap A.
7. Leave the sealant bottle K in the bottleholder E and store the kit away safelyin its original location.
8. Drive to the nearest tyre specialist toget the damaged tyre replaced. Beforethe tyre is removed from the rim, informyour tyre dealer that the tyre containssealant. Renew the kit as soon aspossible after it has been used once.
Note: Remember that emergency roadsidetyre repair kits only provide temporarymobility. Regulations concerning tyre repairafter usage of tyre repair kit may differ fromcountry to country. You should consult atyre specialist for advice.
WARNINGBefore driving, make sure the tyre isadjusted to the recommendedinflation pressure. See Technical
Specifications (page 166). Monitor thetyre pressure until the sealed tyre isreplaced.
Empty sealant bottles can be disposed oftogether with normal household waste.Return remains of sealant to your dealeror dispose of it in compliance with localwaste disposal regulations.
RUN FLAT TYRESPrinciple of operationStandard tyre
BA
C
E75207
Wheel rim position with correcttyre pressure
A
Wheel rim position withinsufficient tyre pressure
B
TyreC
163
Wheels and Tyres
Run flat tyre
B
DC
A
E87667
Wheel rim position with correcttyre pressure
A
Wheel rim position withinsufficient tyre pressure
B
TyreCReinforced sidewallD
When a standard tyre experiences a drasticloss of inflation pressure, the rim of thewheel brings the full weight of the vehicleto bear on the collapsed sidewalls. Youcan barely manoeuvre the vehicle and thetyre is destroyed.Run flat tyres have sturdy, reinforcedsidewalls that support the rim should thetyre suffer a loss of inflation pressure.
What to do if a run flat tyre has apunctureDue to the run-flat properties of thesetyres, you may not notice any tyre defect.Your vehicle is equipped with a tyrepressure monitoring system that alerts youto any drop in tyre pressure. SeeTechnical Specifications (page 166).In the event of a tyre defect:• immediately slow down to a maximum
speed of 80 km/h (50 mph)• avoid sudden or erratic braking and
steering manoeuvres and be especiallycareful negotiating bends
• do not drive more than 80 kilometres(50 miles) after the defect is detected
• have the defective tyre replaced assoon as possible.
Replacing run flat tyresWARNINGS
Make sure that the workshop isaware that your vehicle is equippedwith special run flat tyres.Never repair or reuse run flat tyresthat are damaged or have beendriven on run flat.
If a run flat tyre has to be replaced, havethe respective wheel rim inspected for anydamage.
Do not fit a mixture of run flat andstandard tyres. In isolated cases, astandard tyre can be temporarily
mounted on a vehicle otherwise equippedwith run flat tyres. It must be pointed outto the driver that the standard tyre has norunflat properties.
Do not fit run flat tyres on vehiclesthat were not originally fitted withthem. Please contact your dealer for
more details regarding compatibility.
Run flat tyres may be sold and mountedonly by specially trained and certified tyredealers.
164
Wheels and Tyres
TYRE CARE
E70415
To make sure the front and rear tyres ofyour vehicle wear evenly and last longer,we recommend that you swap the tyresfrom front to rear and vice versa at regularintervals of between 5000 and 10000kilometres (3000 and 6000 miles).
CAUTIONDo not scrub the sidewalls of the tyreswhen you are parking.
If you have to mount a kerb, do so slowlyand approach it with the wheels atright-angles to the kerb.Examine the tyres regularly for cuts, foreignobjects and uneven wear of the tread.Uneven wear could mean that the wheelalignment is outside specification.Check the tyre pressures (including thespare) when cold, every two weeks.
USING WINTER TYRES
CAUTIONMake sure that you use the correctwheel nuts for the type of wheel thewinter tyres are fitted to.
If winter tyres are used, make sure that thetyre pressures are correct. See TechnicalSpecifications (page 166).
USING SNOW CHAINS
WARNINGSDo not exceed 40 km/h (25 mph)when using 14 mm ( 0.6 inch) snowchains or 50 km/h (30 mph) when
using 10 mm ( 0.4 inch) snow chains.Do not use snow chains on snow-freeroads.Only fit snow chains to 235/60 R16or 215/65 R16 tyres.
CAUTIONIf your vehicle is fitted with wheeltrims, remove them before fittingsnow chains.
Note: The ABS will continue to operatenormally.Only use small link snow chains.Only use snow chains on the front wheels.
Vehicles with stability control(ESP)Vehicles with stability control (ESP) mayexhibit some unusual drivingcharacteristics which can be avoided byswitching the system off. See UsingStability Control (page 113).
TYRE PRESSUREMONITORING SYSTEM
WARNINGSThe system does not relieve you ofyour responsibility to regularly checkthe tyre pressures.The system will only provide a lowtyre pressure warning. It will notinflate the tyres.
165
Wheels and Tyres
WARNINGSDo not drive on significantlyunder-inflated tyres. This may causethe tyres to overheat and fail.
Under-inflation reduces fuel efficiency, tyretread life and may also affect your abilityto drive the vehicle safely.
CAUTIONSDo not bend or damage the valveswhen you are inflating the tyres.Have tyres installed by properlytrained technicians.
The Deflation Detection System will alertyou if there is a change of air pressure inany tyre. It does this by using the ABSsensors to detect the rolling circumferenceof the wheels. When the circumferencechanges, this indicates low pressure in atyre, a warning message is displayed in theinformation display and the messageindicator will illuminate. See InformationMessages (page 74).Apart from a too low tyre pressure or adamaged tyre, the following situations canaffect the rolling circumference:• Vehicle load is uneven.• When using a trailer or travelling up and
down an incline.• Using snow chains.• Driving on soft surfaces such as snow
or mud.
Note: The system will still functioncorrectly, but there may be an increaseddetection time.If a low pressure warning message isdisplayed in the information display, checkthe tyre pressures as soon as possible andinflate them to the recommendedpressure. See Technical Specifications(page 166).If this happens frequently, have the causedetermined and rectified as soon aspossible.
System resetNote: Do not reset the system when thevehicle is moving.Note: You should reset the systemfollowing any adjustment to the tyrepressures or any changing of tyres.Note: Turn the ignition on.
Type 2 instrument cluster1. Using the multifunction lever, navigate
to 'SET' > T. Pres.2. Press and hold the SET/RESET
button until the message TyrePressure set appears.
Type 3 instrument cluster1. Using the multifunction lever, navigate
to hold 'SET' to set Tyre Pres.2. Press and hold the SET/RESET
button until the message TyrePressure set appears.
TECHNICAL SPECIFICATIONSWheel nut torque
Nm (Ib-ft)Wheel type
130 (96)All
166
Wheels and Tyres
Tyre pressures (cold tyres)
Up to 80 km/h (50 mph)Tyre Pressures
Full LoadNormal Load
Tyre SizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
4.2 (61)4.2 (61)4.2 (61)4.2 (61)T135/90 R 17All
Up to 160 km/h (100 mph)Tyre Pressures
Full LoadNormal Load
Tyre SizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.4 (35)2.3 (33)2.2 (32)215/65 R16All
2.8 (41)2.4 (35)2.3 (33)2.2 (32)235/60 R16All
2.8 (41)2.4 (35)2.3 (33)2.2 (32)235/55 R17All
2.8 (41)2.4 (35)2.3 (33)2.2 (32)235/55 RF17All
2.8 (41)2.4 (35)2.2 (32)2.1 (31)235/50 R18All
2.8 (41)2.4 (35)2.2 (32)2.1 (31)235/45 R19All
Continuous speed in excess of 160 km/h (100 mph)Tyre Pressures
Full LoadNormal Load
Tyre SizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.4 (35)2.3 (33)2.3 (33)215/65 R16All
167
Wheels and Tyres
Full LoadNormal Load
Tyre SizeVariant RearFrontRearFront
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
bar(lbf/in²)
2.8 (41)2.4 (35)2.3 (33)2.3 (33)235/60 R16All
2.8 (41)2.4 (35)2.3 (33)2.3 (33)235/55 R17All
2.8 (41)2.4 (35)2.3 (33)2.3 (33)235/55 RF17All
2.8 (41)2.4 (35)2.3 (33)2.3 (33)235/50 R18All
2.8 (41)2.4 (35)2.3 (33)2.3 (33)235/45 R19All
168
Wheels and Tyres
VEHICLE IDENTIFICATIONPLATENote: The vehicle identification platedesign may vary to that shown.Note: The information shown on the vehicleidentification plate is dependant uponmarket requirements.
E85610C
B
E D
A
Vehicle identification numberAGross vehicle weightBGross train weightCMaximum front axle weightDMaximum rear axle weightE
The vehicle identification number andmaximum weights are shown on a platelocated on the lock side of the right-handfront door aperture at the bottom.
VEHICLE IDENTIFICATIONNUMBER
E87496
The vehicle identification number isstamped into the floor panel on theright-hand side, beside the front seat. It isalso shown on the left-hand side of theinstrument panel.
169
Vehicle identification
TECHNICAL SPECIFICATIONSTowing equipment dimensions
Dimension in mm (inches)Dimension description
4443 (174.9)Maximum length
2128 (83.8)Overall width including exterior mirrors
1655 - 1677 (65.2 - 66)Overall height - EC kerb weight without roof bars
1687 - 1710 (66.4 - 67.3)Overall height - EC kerb weight including roof bars
2690 (105.9)Wheelbase
1574 - 1580 (62 - 62.2)Front track
1584 - 1590 (62.4 - 62.6)Rear track
170
Capacities and Specifications
Towing equipment dimensions
A
B
G
F
E
C
D
E99436
171
Capacities and Specifications
Dimension in mm (inches)Dimension descriptionItem
98 (3.9)Bumper – end of tow ballA
87 (3.4)Attachment point – centre of tow ballB
918 (36.1)Wheel centre – centre of tow ballC
518 (20.4)Centre of tow ball – side memberD
1031 (40.6)Distance between side membersE
446 (17.6)Centre of tow ball – centre 1. attachmentpointF
746 (29.4)Centre of tow ball – centre 2. attachmentpointG
172
Capacities and Specifications
IMPORTANT AUDIOINFORMATION
WARNINGSDue to technical incompatibility,recordable (CD-R) and rewritable(CD-RW) discs may not function
correctly.These units will play compact discsthat conform to the InternationalRed Book standard audio
specification. Copy protected CDs fromsome manufacturers do not conform tothis standard and playback cannot beguaranteed.
Dual format, dual sided discs (DVDPlus, CD-DVD format), adopted bythe music industry, are thicker than
normal CDs and consequently playbackcannot be guaranteed, and jamming couldoccur. Irregular shaped CDs and CDs witha scratch protection film or self adhesivelabels attached should not be used.Warranty claims, where this type of disc isfound to be inside an audio unit returnedfor repair, will not be accepted.
All units except Sony CD (but not the6CD) are designed to playcommercially pressed 12 cm audio
compact discs only. The Sony CD unit willplay 8 cm discs with a Sony approvedadaptor fitted (CSA-8).
The audio unit may be damaged ifunsuitable items like credit cards orcoins are pushed inside the CD
aperture.
Audio unit labels
E66256
E66257
Disc labelsAudio CD
E66254
MP3
E66255
173
Audio introduction
6000CD
A B C D E
O
G
N
E138367
F
H
G
M IL JK
CD select. See Compact disc player (page 188).ACD aperture. See Loading compact discs (page 188).BCD eject. See Ejecting compact discs (page 191).COn, off and volume control. See On/off control (page 179).DWaveband select. See Waveband button (page 181).EClock. See Setting the clock and date on the audio unit (page 178).FStation presets. See Station preset buttons (page 181).GTraffic announcement. See Traffic information control (page 182).HAccept call and phone menu. See Telephone (page 195).ISeek up. See Station tuning control (page 183).JMenu. See Audio menu control (page 179).KSeek down. See Station tuning control (page 183).LBalance and fade control. See Balance/fade control (page 179).MBase and treble control. See Bass/treble control (page 179).NAuxiliary select. See Auxiliary input (AUX IN) socket (page 193).O
174
Audio unit overview
Sony CD and Sony CD DAB
E138370
G
H
I
J
S
R
Q
P
C DA B E F
KMO N L
Scan. See Station tuning control (page 183). See Compact disc trackscanning (page 191).
A
Information. See Audio unit operation (page 179). See Audio unit menus(page 185). See Compact disc player (page 188). See Audio troubleshooting(page 194).
B
Station presets. See Station preset buttons (page 181).CCD aperture. See Loading compact discs (page 188).DClock. See Setting the clock and date on the audio unit (page 178).EDSP select. See Digital signal processing (DSP) (page 185).FAutostore. See Autostore control (page 182).GMenu. See Audio menu control (page 179).HTraffic announcement. See Traffic information control (page 182).IOn and off control. See On/off control (page 179).JBalance and fade control. See Balance/fade control (page 179).KEnd call. See Telephone (page 195).LVolume control, navigation buttons and select button.MAccept call. See Telephone (page 195).N
175
Audio unit overview
Tone. See Bass/treble control (page 179).OPhone menu. See Telephone (page 195).PRadio and waveband select. See Waveband button (page 181).QAuxiliary and CD select. See Auxiliary input (AUX IN) socket (page 193). SeeCompact disc player (page 188).
R
CD eject. See Ejecting compact discs (page 191).S
176
Audio unit overview
SECURITY CODEEach unit incorporates a unique code thatmust be entered before the unit willoperate.If the battery is disconnected or if the unithas been removed from the vehicle, thecode must be re-entered before the unitwill operate.
LOST SECURITY CODEIf you lose the unique code, contact yourdealer and supply details of your audio unitalong with some proof of identity.
ENTERING A SECURITY CODEIf CODE - - - -, CODE 0000 or ENTERKEYCODE appears in the display whenyou switch on the audio unit, you mustenter the unique code using the stationpreset buttons.
6000CD, Sony and Sony DAB1. Using the station preset buttons enter
the unique code.2. If you make a mistake entering the
code, re-enter the digits by continuingto select buttons 0-9. The display willadvance from digit position 1 to 4 andthen back again.
3. Make sure that the complete code iscorrect before pressing either the *preset button or the button betweenthe navigation buttons to confirm yourselection.
INCORRECT SECURITY CODEUp to a maximum of 10 unique code entryattempts are allowed with variousconsequences if you get it wrong.
The number of attempts will be shown inthe display.If the display reverts to CODE anotherentry attempt may be made immediately.If the display shows WAIT 30, the unit willbe locked for 30 minutes. Wait until thetimer counts down to zero. When CODE isshown in the display, enter the correctcode.Note: After 10 incorrect attempts the unitwill be permanently inoperative andLOCKED will be shown in the display. Seeyour dealer.
177
Audio system security
SETTING THE CLOCK ANDDATE ON THE AUDIO UNIT6000CDChanging the date and timePress the CLOCK button to display thedate and time.Note: If you do not press another buttonwithin 30 seconds of pressing the CLOCKbutton, the display will return to its previoussetting.1. Using the seek up or seek down button
select the date or time value that youwish to change. The selected value willflash in the display.
2. Rotate the volume control to changethe selected date or time value.
3. Using the seek up or seek down buttonselect additional date or time valuesthat you wish to change.
4. Rotate the volume control to changethe selected date or time value.
5. Press the CLOCK button to exit andsave your settings.
Note: If you do not press the CLOCK buttonwithin 30 seconds of changing a date ortime value, the display will exit and save thenew values automatically.Note: Press and hold the CLOCK buttonfor more than two seconds to automaticallyselect the hour value for winter or summertime adjustment.
12/24 hour format1. Press the MENU button repeatedly
until the 12/24 icon is shown in thedisplay.
2. Using the seek up or seek down buttonselect your required setting.
3. Press the MENU button repeatedly orallow the system to time out to confirmyour selection.
Sony and Sony DABChanging the date and time1. Press the CLOCK button.2. Press the left or right navigation button
until the date or time value that youwish to change flashes in the display.
3. Using the up or down navigation buttonchange the selected date or time value.
4. Using the left and right navigationbuttons select additional date or timevalues that you wish to change. Theselected value will flash in the display.
5. Repeat steps three and four asnecessary.
6. Press the CLOCK button or the buttonbetween the navigation buttons to exitand save your settings.
12/24 hour format1. Press the MENU button.2. Press the up or down navigation button
until the 12/24 icon is shown in thedisplay.
3. Using the left or right navigation buttonselect the required setting.
4. Press the MENU button or the buttonbetween the navigation buttons toconfirm your selection.
178
Audio unit clock and date displays
ON/OFF CONTROLPress the on/off control. This will alsooperate the unit for up to one hour with theignition turned off.The radio will switch off automaticallyafter one hour.
BASS/TREBLE CONTROLThe bass function is used to adjust thelow-frequency response of the audio unit.The treble function is used to adjust thehigh-frequency response of the audio unit.
All except Sony and Sony DABNote: The selected level will be shown inthe display.1. Press the BASS/TRE button once for
bass or twice for treble.2. Use the volume control or on some
units the seek up or seek down buttonto make the necessary adjustment.
Sony and Sony DABNote: You can adjust these settingsseparately for CD, Radio and Aux.Note: The selected level will be shown inthe display.1. Press the TONE button once for bass
or twice for treble.2. Use the up and down navigation
buttons to make the necessaryadjustment.
BALANCE/FADE CONTROLThe balance function is used to adjust thesound distribution between the left andright speakers.The fade function is used to adjust thesound distribution from front to rear invehicles fitted with rear speakers.Press the FAD/BAL button once for fadeor twice for balance.
All except Sony and Sony DABUse the volume control or on some unitsthe seek up or seek down button to makethe necessary adjustment.
Sony and Sony DABUse the up and down navigation buttonsfor fade adjustment, and the left and rightnavigation buttons for balance adjustment.The selected level will be shown in thedisplay.
AUDIO MENU CONTROLUse the MENU button to access functionsthat cannot be selected directly via one ofthe control buttons. Press the MENUbutton for first level functions, or press andhold the MENU button for other secondlevel functions (not available on Sony orSony DAB audio units).
179
Audio unit operation
6000CD
Menu functions
Second levelFirst level
During all functionsDuring CD playbackDuring tape playbackDuring radio recep-tion
Traffic local ordistant
Scan12/24 hourManual tuning
AF**ShuffleAVC*Scan tuning
REGRepeatADV menu12/24 hour
NewsComp-AVC*
CLIP12/24 hour-ADV menu
VIDAVC*--
Bluetooth enable/disable
ADV menu--
Note: The sequence in which functions appear may vary for different audio units andvehicles.Note: Second level functions (advanced) can also be entered by selecting ADV menu fromthe first level menu.*Automatic volume control.** Alternative frequencies.
Sony CD and Sony CD DAB
Menu functions
During CD playbackDuring radio reception
12/24 hour12/24 hour
CLIP ON/OFFCLIP ON/OFF
News ON/OFFNews ON/OFF
AVC1AVC1
AF2AF2
180
Audio unit operation
Menu functions
During CD playbackDuring radio reception
TA3 volumeTA3 volume
Traffic local or distantTraffic local or distant
ShuffleRegional ON/OFF
Repeat-
Comp ON/OFF-Note: The sequence in which functions appear may vary for different audio units andvehicles.1Automatic volume control.2Alternative frequencies.3Traffic announcement.
Sony CD and Sony CD DAB withBluetoothPressing PHONE followed by the MENUbutton will access the following options:• No active phone or Active phone• Debond BT device• Reject calls ON/OFF• Bluetooth ON/OFF.
WAVEBAND BUTTONNote: The selector can also be used toreturn to radio reception when you havebeen listening to another source.
All except Sony and Sony DABPress the AM/FM button to select fromthe wavebands available.
Sony and Sony DABPress the RADIO button to select from thewavebands available.
STATION PRESET BUTTONSThis feature allows you to store yourfavourite stations so that they can berecalled by selecting the appropriatewaveband and pressing one of the presetbuttons.1. Select a waveband.2. Tune to the station required.3. Press and hold one of the preset
buttons. The audio unit will mute.When sound returns the station hasbeen stored.
This can be repeated on each wavebandand for each preset button.Note: When you drive to another part of thecountry, FM RDS (radio data system)stations that broadcast on alternativefrequencies are stored on the presetbuttons.
181
Audio unit operation
AUTOSTORE CONTROLNote: This function will overwrite thepreviously stored autostore preset stations.Note: This function can also be used tostore stations manually in the same way asother wavebands.Note: The strongest signals available onthe selected waveband will be stored.The sound is muted and AUTOSTORE willbe shown in the display while the unitsearches through the frequencies.When the search is complete, sound isrestored and the strongest signals arestored on the autostore presets.
6000CDPress and hold the AM/FM button.
Sony CDPress and hold the AST or RADIO button.
TRAFFIC INFORMATIONCONTROLMany stations that broadcast on the FMwaveband have a TP code to signify thatthey carry traffic programme information.
Activating traffic announcementsBefore you can receive trafficannouncements, you must press the TAbutton. Either TA-D or TA-L will be shownin the display to indicate that the featureis switched on.If you are already tuned to a station thatbroadcasts traffic information, TP will alsobe shown in the display. Otherwise the unitwill search for a traffic programme anddisplay TP SEEK while doing so. If it cannotlocate such a station, NOT FOUND will beshown in the display.
TP will be shown within a box in the displaywhen you are tuned to a station providingtraffic information from a linked RDS (radiodata system) or EON (enhanced othernetwork) station.When traffic information is broadcast, itwill automatically interrupt normal radio,tape or CD playback and TRAFFIC orNEWS will be shown in the display.If the traffic signal weakens, TP will flashin the display. Press the seek up or seekdown button (the left or right navigationbutton on Sony or Sony DAB audio units)to find another station.Note: If this happens during CD or AUXplayback or, on certain models, with theradio volume set to zero, the unit will retuneautomatically if the station is not available.If a non-traffic station is selected orrecalled using a preset button, the audiounit will remain on that station unless TAis turned off, then on again.Note: If TA is on and you select a preset ormanual tune to a non TA station no trafficannouncement will be heard.
Local or distant trafficThe number of RDS or EON trafficannouncements may become excessivein some areas so there is an option toselect between local traffic informationand all available information.
6000CD1. Press and hold the MENU button until
the display changes.2. Press the MENU button repeatedly
until TA is shown in the display.
182
Audio unit operation
3. Press the seek up or seek down buttonto select either local (TA LOCAL) ordistant (TA DIST) trafficannouncements.
4. Press the MENU button or allow themenu to time out to confirm yourselection.
Note: Either TA-L or TA-D will be shown inthe display.
Sony CD1. Press the MENU button and use the
up or down navigation button to selectthe TA display.
2. Press the left or right navigation buttonto select your required setting.
3. Press the MENU button to confirmyour selection.
Traffic announcement volumeTraffic announcements interrupt normalbroadcasts at a preset minimum level thatis usually louder than normal listeningvolumes.
To adjust the preset volume6000CD1. Press and hold the TA button.2. Rotate the volume control to make the
necessary adjustment.Note: The selected level will be shown inthe display.
Sony CD1. Press and hold the TA button.2. Press the left or right navigation button
to make the necessary adjustment.Note: The selected level will be shown inthe display.
Ending traffic announcementsThe audio unit will return to normaloperation at the end of each trafficannouncement. To end the announcementprematurely, press TA during theannouncement.Note: If you press TA at any other time itwill switch all announcements off.
STATION TUNING CONTROLDAB service linkingNote: The DAB service linking is as perdefault off.Note: Service linking allowscross-referencing to other correspondingfrequencies of the same station, for exampleFM and other DAB ensembles.Note: The system will automaticallychange to another corresponding station ifthe current one becomes unavailable, forexample when leaving the coverage area.
Switching DAB service linking on andoff1. Press the MENU button.2. Using the up or down navigation button
scroll through the display until DIGITALRADIO SERVICE LINK is shown in thedisplay.
3. Using the left or right navigation buttonselect AUTO or OFF.
4. Press the MENU button or the buttonbetween the navigation buttons toconfirm your selection.
Seek tuning6000CDSelect a waveband and briefly press theseek up or seek down button. The unit willstop at the first station it finds in thedirection you have chosen.
183
Audio unit operation
Sony CDSelect a waveband and briefly press theup or down navigation button. The unit willstop at the first station it finds in thedirection you have chosen.
Manual tuning6000CD1. Select a waveband and press the
MENU button until MAN is shown inthe display.
2. Press the seek up or seek down buttonto tune up or down the waveband insmall increments or press and hold toincrement quickly, until you find astation you want to listen to.
Sony CDSelect a waveband and briefly press theup or down navigation button to tune upor down the waveband in smallincrements. The display shows thefrequency selected.
Sony DABNote: Ensembles are groups of stations.Briefly press the up or down navigationbutton to move up or down the ensembles.
Scan tuningThe SCAN function allows you to listen to10 seconds of each station detected.
6000CD1. Press the MENU button repeatedly
until SCAN is shown in the display.2. Press the seek up or seek down button
to scan up or down the selectedwaveband.
3. Depending on the audio unit, press theseek up or seek down button or theMENU button to continue listening toa station.
Sony and Sony DAB1. Press the SCAN button. SCAN flashes
or SCANNING is shown in the display.2. Press the left or right navigation button
to scan within a waveband.3. Press SCAN again to continue listening
to a station.
184
Audio unit operation
AUTOMATIC VOLUMECONTROLWhen available, automatic volume control(AVC) adjusts the volume level tocompensate for engine noise and roadspeed noise.
All except Sony and Sony DAB1. Press the MENU button repeatedly
until AVC is shown in the display.2. Use the seek up or seek down button
to adjust the AVC setting.3. Press the MENU button or allow the
system to time out to confirm yourselection.
Sony and Sony DAB1. Press the MENU button briefly.2. Using the up or down navigation button
select AVC.3. Press the MENU button or allow the
system to time out to confirm yourselection.
DIGITAL SIGNAL PROCESSING(DSP)DSP occupancyThis feature takes into account thedifferences in distance from the variousspeakers in the vehicle to each seat. Selectthe sitting position for which the audio isto be correctly enhanced.
DSP equaliserSelect the music category that most suitsyour listening preference. The audio outputwill change to enhance the particular styleof music chosen.
Changing the DSP settings1. Press the DSP button once for
occupancy and twice for equaliser. Foritem location: See Audio unitoverview (page 174).
2. Use the up and down navigationbuttons to select the required setting.
3. Press the button between thenavigation buttons to confirm yourselection.
AUDIO DISTORTIONREDUCTION (CLIP)When available CLIP automatically detectssound distortion and reduces the volumelevel until the distortion has beeneliminated. This means that whilst thedisplay might change numerically whenyou raise the volume manually with thecontrol, there may be no actual increasein sound.
All except Sony and Sony DAB1. Press and hold the MENU button until
the display changes.2. Press the MENU button repeatedly
until CLIP is shown in the display.3. Using the seek up or seek down button
turn the function on or off.4. Press the MENU button or allow the
system to time out to confirm yourselection.
Sony and Sony DAB1. Press the MENU button briefly.2. Using the up or down navigation button
select CLIP.3. Press the MENU button or allow the
system to time out to confirm yourselection.
185
Audio unit menus
ALTERNATIVE FREQUENCIESMany programmes broadcast on the FMwaveband have a programmeidentification (PI) code, which can berecognised by audio units.If your radio has alternative frequencies(AF) tuning switched on and you movefrom one transmission area to another, thisfunction will search for and switch to astronger station signal, if one can be found.Under certain conditions, however, AFtuning may temporarily disrupt normalreception.When selected, the unit continuallyevaluates signal strength and, if a bettersignal becomes available, the unit willswitch to that alternative. It mutes whileit checks a list of alternative frequenciesand, if necessary, it will search once acrossthe selected waveband for a genuinealternative frequency.It will restore radio reception when it findsone or, if one is not found, the unit willreturn to the original stored frequency. Oncertain units, NOT FOUND will be shownin the display.With AF-MAN selected, the unit operatesin a similar way to AF-AUTO or AF-ON, butonly searches for an alternative frequencywhen prompted by pressing a presetbutton.With AF-OFF selected, the original storedfrequency remains selected. In this mode,AF-OFF will be displayed every time theunit is turned on.
All except Sony and Sony DAB1. Press and hold the MENU button until
the display changes.2. Press the MENU button repeatedly
until AF is shown in the display.
3. Using the seek up or seek down buttonselect the required setting.
4. Press the MENU button or allow thesystem to time out to confirm yourselection.
Sony and Sony DAB1. Press the MENU button briefly.2. Using the left or right navigation button
select the required setting.3. Press the MENU button to confirm
your selection.
REGIONAL MODE (REG)Regional mode (REG) controls thebehaviour of AF switching betweenregionally related networks of a parentbroadcaster. A broadcaster may run a fairlylarge network across a large part of thecountry. At various times of the day thislarge network may be broken down into anumber of smaller regional networks,typically centred on major towns or cities.When the network is not split into regionalvariants, the whole network caries thesame programming.Regional mode ON: This prevents 'random'AF switches when neighbouring regionalnetworks are not carrying the sameprogramming.Regional mode OFF: This allows a largercoverage area if neighbouring regionalnetworks are carrying the sameprogramming, but can cause 'random' AFswitches if they are not.
All except Sony and Sony DAB1. Press and hold the MENU button until
the display changes.2. Press the MENU button repeatedly
until REG is shown in the display.
186
Audio unit menus
3. Using the seek up or seek down buttonturn the function on or off.
4. Press the MENU button or allow thesystem to time out to confirm yourselection.
Sony and Sony DAB1. Press the MENU button briefly.2. Using the up or down navigation button
select REGIONAL.3. Press the MENU button or allow the
system to time out to confirm yourselection.
NEWS BROADCASTSSome audio units interrupt normalreception to broadcast news bulletins fromstations on the FM waveband or radio datasystem (RDS) and enhanced othernetwork (EON) linked stations, in the sameway as traffic information is provided.During news broadcasts, the displayalternates between the station name andNEWS. News interrupts are broadcast atthe same preset volume level as trafficannouncements.
All except Sony and Sony DAB1. Press and hold the MENU button until
NEWS is shown in the display.2. Using the seek up or seek down button
turn the function on or off.3. Press the MENU button to confirm
your selection.
Sony and Sony DAB1. Press the MENU button.2. Using the up or down navigation button
scroll through the display until NEWSis shown in the display.
3. Press the button between thenavigation buttons to make yourselection.
4. Using the left or right navigation buttonturn the function on or off.
5. Press the MENU button or the buttonbetween the navigation buttons toconfirm your selection.
187
Audio unit menus
LOADING COMPACT DISCS6000CD, Sony and Sony DABAlways check that the CD aperture isempty before inserting a CD.Insert a CD, label side up, into the audiounit.LOADING, READING CD and AUDIO CDor MP3 CD will be shown in the display,and playback will start automatically.
TRACK SELECTIONAll except Sony and Sony DAB1. Press the SEEK UP button once to
move to the next track or press itrepeatedly to access later tracks.
2. Press the SEEK DOWN button onceto replay the current track. If pressedwithin two seconds of the start of atrack, the previous track will beselected.
3. Press the SEEK DOWN buttonrepeatedly to select previous tracks.
Sony and Sony DAB1. Press the up navigation button once to
move to the next track or press itrepeatedly to access later tracks.
2. Press the down navigation button onceto replay the current track. If pressedwithin two seconds of the start of atrack, the previous track will beselected.
3. Press the down navigation buttonrepeatedly to select previous tracks.
LOADING THE COMPACT DISCCHANGER
CAUTIONSDo not insert more than one disc intoeach slot.Keep the door closed when themagazine is installed.
Note: The unit will only accept conventionalCD's.For item location: See CD changer (page96).
E66144
1. Open the door.2. Press the button.3. Remove the magazine.4. Insert a disc, with the label facing
upwards, into each slot. You will heara distinct click to confirm correctloading.
5. Install the magazine in the directionindicated by the arrow on themagazine. You will hear a distinct clickto confirm correct loading.
6. Close the door.
188
Compact disc player
UNLOADING THE COMPACTDISC CHANGER
CAUTIONKeep the door closed when themagazine is installed.
1. Open the door.2. Press the button.3. Remove the magazine.4. Pull the tray out using the lever on the
side.5. Remove the CD and close the tray.6. Repeat steps four and five to remove
remaining CD's.7. Install the magazine in the direction
indicated by the arrow on themagazine. You will hear a distinct clickto confirm correct loading.
8. Close the door.
COMPACT DISC PLAYBACKNote: During playback, the display indicatesthe disc, track and time that has elapsedsince the start of the track.Note: On CD changer audio units, if two ormore CD's are loaded one after the other,playback will start with the last CD loaded.
6000CDDuring radio reception, press the CD buttononce to start CD playback.Playback will start immediately after a discis loaded.
Sony and Sony CD DABDuring radio reception, press the CD/AUXbutton once to start CD playback.Playback will start immediately after a discis loaded.
Compact disc changer playback6000CDPress the CD button twice to start CDplayback.Note: If the CD button is pressed when nodiscs are loaded, NO CDS will be shown inthe display.
Sony and Sony CD DABPress the CD/AUX button twice to startCD playback.Note: If the CD/AUX button is pressedwhen no discs are loaded, NO CDS will beshown in the display.
FAST FORWARD/REVERSEAll except Sony and Sony DABPress and hold the seek up or the seekdown button to search forwards orbackwards within the tracks on the disc.
Sony and Sony DABPress and hold the left or right navigationbutton to search forwards or backwardswithin the tracks on the disc.
SHUFFLE/RANDOMRandom track playback, also known asshuffle, plays all tracks on a CD in randomorder.
6000CDNote: When SHUFF CD is selected only thetracks on the current CD will be shuffled.When SHUF ALL is selected the tracks onall the CD's will be shuffled.
189
Compact disc player
1. Press the MENU button repeatedlyuntil SHUF is shown in the display.
2. Using the seek up or seek down buttonscroll through the display until SHUFALL or SHUFF CD is shown in thedisplay.
3. Using the seek up or seek down buttonselect the next track to shuffle ifrequired.
Note: With the function on, SHUFFLE willbe shown in the display as each new trackis selected.
Sony CD and Sony CD DAB1. Press the MENU button.2. Using the up or down navigation button
scroll through the display untilSHUFFLE is shown in the display.
3. Use the left or right navigation buttonto switch the function on and off.
Note: When an MP3 CD is playing, optionsinclude SHUFF CD for the whole CD, orSHUF ALL to play all the tracks in the folderin a random order.
COMPACT DISC TRACKCOMPRESSIONWith this feature on, quieter music isboosted and louder music lowered tominimise repeated volume adjustments.
All except Sony and Sony DAB1. Press MENU repeatedly until COMP is
shown in the display.2. Using the seek up or seek down button
turn the function on or off.3. Press the MENU button to confirm
your selection.
Sony and Sony DAB1. Press the MENU button.2. Using the up or down navigation button
scroll through the display until COMPis shown in the display.
3. Press the button between thenavigation buttons to make yourselection.
4. Using the left or right navigation buttonturn the function on or off.
5. Press the MENU button or the buttonbetween the navigation buttons toconfirm your selection.
REPEAT COMPACT DISCTRACKS6000CD1. Press the MENU button repeatedly
until REPEAT is shown in the display.2. Using the SEEK UP or SEEK DOWN
button choose between OFF and TRK.
Sony and Sony DAB1. Press the MENU button.2. using the up or down navigation
buttons scroll through the display untilREPEAT is shown in the display.
3. Using the left or right navigationbuttons select REPEAT TRACK orREPEAT OFF.
4. Press the MENU button to confirmyour selection.
Note: When an MP3 CD is playing, playbackoptions are REPEAT TRACK, REP FOLDERand REPEAT OFF.
190
Compact disc player
COMPACT DISC TRACKSCANNINGThe SCAN function allows you to previeweach track for approximately 10 seconds.
6000CDNote: When selected, SCAN will be shownbriefly in the display at the start of eachtrack.1. Press the MENU button repeatedly
until SCAN is shown in the display.2. Using the seek up or seek down button
select either SCAN CD or SCAN ALL.3. Press the seek up or seek down button
again to continue listening to a track.
Sony and Sony DABNote: Various scan modes are possible,according to the type of CD currentlyplaying.1. Press the SCAN button once to scan
each track on an audio CD, or the first10 seconds of each track on each folderof a MP3 CD.
2. Press the SCAN button again to selectSCAN OFF (audio CD), or in the caseof MP3 to scan each track within afolder.
EJECTING COMPACT DISCSNote: Radio reception is restoredautomatically when the EJECT button ispressed.Note: If the EJECT button is pressed inerror, press the button again to cancel.Note: If the CD is not removed it will bepulled back into the audio unit.
6000CDPress the EJECT button at any time andremove the CD.
Sony CDNote: If no CD is loaded when the EJECTbutton is pressed, NO CD will be shown inthe display.Press the EJECT button at any time andremove the CD. EJECTING and PLEASEREMOVE will be shown in the display.
MP3 FILE PLAYBACKNote: Some copy protected audio files maynot be read by the CD player.The CD player also supports MP3 andWMA format audio files.When a CD containing audio is insertedinto the CD player the disc's directorystructure is read in. It may take a whilebefore playback starts and is dependanton the quality of the disc.MP3 tracks may be recorded on the CD inseveral ways. They can all be placed in theroot directory like a conventional audio CD,or they can be placed in folders that mayrepresent, for example, an album, an artist,or a genre.
Playing a multi session discThe normal playing sequence on CD's withmultiple folders is to play the tracks in thefirst folder, then the tracks in any foldersnested inside the first folder, then moveonto the second folder, and so on. Forexample, if folder 1 has folders 1a and 1bwithin it, and folder 2 contains folder 2a,the playing sequence will be folder 1, 1a, 1b,2, 2a.
191
Compact disc player
When the playback of a file is finished theplayback of the other files in the samedirectory continues. Directory change takesplace automatically when all files in thecurrent directory have been played back.
MP3 DISPLAY OPTIONSWhen an MP3 disc is playing, certaininformation encoded in each track can bedisplayed. Such information will normallyinclude:• The file name• The folder name• ID3 information which might be the
album or artist’s name.The unit will normally show the file namethat is playing. To select one of the otheritems of information, press the INFObutton repeatedly until the required itemis shown in the display.Note: If the ID3 information selected isunavailable, NO MP3 TAG will be shown inthe display.
CD text display optionsWhen an audio disc with CD text is playing,limited information encoded in each trackcan be displayed. Such information willnormally include:• The disc name• The artist name• The track name.Note: These display options are selectedin the same way as MP3 displays. NO DISCNAME or NO TRACK NAME will be shownin the display if no information has beenencoded.
ENDING COMPACT DISCPLAYBACKAll except Sony and Sony DABPress the AM/FM button.Note: This will not eject the CD; the discwill merely pause at the point where radioreception was restored.To resume CD playback, press the CDbutton again.
Sony and Sony DABPress the RADIO button.Note: This will not eject the CD; the discwill merely pause at the point where radioreception was restored.To resume CD playback, press theCD/AUX button again.
192
Compact disc player
Note: For optimum performance whenusing any auxiliary device set the volume onthe device high. This will reduce audiointerference when charging the device viathe vehicle power supply socket.When fitted the Auxiliary input (AUX IN)socket permits an auxiliary device, such asan MP3 player, to be linked into the vehicleaudio system. Output can be playedthrough the vehicle speakers.To connect an auxiliary device, plug it intothe AUX IN socket using a 3.5 mmconventional audio jack connector.Select the auxiliary input via the AUXbutton and playback will be heard throughthe vehicle speakers. AUX will be shown inthe display. Volume, treble and bass canbe adjusted on the audio unit as normal.The audio unit buttons can also be usedto restore playback from the audio unit,while the auxiliary device remainsconnected.
193
Auxiliary input (AUX IN) socket
RectificationAudio unit display
General error message for CD fault conditions, forexample cannot read the CD, data-CD inserted. Mayalso indicate a audio unit malfunction. Make sure thatthe disc is correctly loaded, clean and re- load the CDor replace the CD with a known music CD. See Ejectingcompact discs (page 191). See Loading compactdiscs (page 188). If error continues. See your dealer.
CD ERRORPLEASE CHECK CD
CDC ERROR
Message to indicate that the audio unit or CD changeris empty. Insert a CD. See Loading compact discs(page 188).
NO CDNO CDSNO CD #
Ambient temperature too hot – unit will not work untilit has cooled down.
HIGH TEMPCD DRIVE HIGH TEMP
Message to indicate that the CD slot is already loaded.Eject the CD from selected slot before attempting loadoperation or select another slot location. See Loadingcompact discs (page 188).
SLOT FULL
Message to indicate that the audio unit is full. SeeEjecting compact discs (page 191).CDC FULL
An incompatible CD has been inserted, for example notan audio CD. See Ejecting compact discs (page 191).DATA CD
Message to prompt you for the Keycode. See Enteringa security code (page 177).CODE ----
Message to inform you to wait until the next keycodeentry attempt can be made. See Incorrect securitycode (page 177).
WAIT
Message indicates the number of incorrect inputattempts. See Incorrect security code (page 177).TRIES
Message to inform you that audio unit security systemhas locked the unit after repeated incorrect keycodeentries. See your dealer.
LOCKED
Message to prompt you for the Keycode. See Enteringa security code (page 177).
KEYCODE....ENTER KEYCODE....
Message to inform you that the entered keycode isincorrect. See Incorrect security code (page 177).INCORRECT
194
Audio troubleshooting
GENERAL INFORMATION
CAUTIONUsing the system with the engine offwill drain the battery.
This section describes the functions andfeatures of the Bluetooth mobile phonehands free system.The Bluetooth mobile phone part of thesystem provides interaction with the audioor navigation system and your mobilephone. It allows you to use the audio ornavigation system to make and receivecalls without having to hold your mobilephone.
Compatibility of phonesCAUTION
As no common agreement exists,mobile phone manufacturers are ableto implement a variety of profiles in
their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insome cases may significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.
Please visit the website www.ford-mobile-connectivity.com for full details.
TELEPHONE SETUPPhonebookAfter start up access to the phonebook listcan be delayed for several minutes,depending upon the size.
Phonebook categoriesDepending on your phonebook entry,different categories can be displayed inthe audio unit.For example:
MobileM
OfficeO
HomeH
FaxF
Note: Entries may be displayed without acategory attachment.The category can also be indicated as anicon:
E87990
Phone
E87991
Mobile
E87992
Home
E87993
Office
E87994
Fax
Making a phone an active phoneWhen using the system for the first time,no phone is connected to the system.
Bluetooth phoneAfter bonding a Bluetooth phone to thesystem, this becomes the active phone.For further information refer to the phonemenu.
195
Telephone
Select the phone from the active phonemenu.Turning the ignition and radio or navigationunit back on again, the last active phoneis picked up by the system.Note: In some cases the Bluetoothconnection must also be confirmed on thephone.
Bond another Bluetooth phoneBond a new Bluetooth phone as describedin the requirements for a Bluetoothconnection.Phones stored in the system are accessibleby using the phone list on the audio unit.Note: A maximum of six devices may bebonded. If six Bluetooth devices havealready been bonded, one of these has tobe debonded in order to bond a new device.
BLUETOOTH SETUPBefore you can use your telephone withyour vehicle it must be bonded to thevehicle telephone system.
Handling of phonesUp to six Bluetooth devices can be bondedto the vehicle system.Note: If there is an ongoing call when thephone in use is selected as the new activephone, the call is transferred to the vehicleaudio system.Note: Even if connected to the car system,your phone can still be used in the usualway.
Requirements for BluetoothconnectionThe following are required before aBluetooth phone connection can be made.
1. The Bluetooth feature must beactivated on the phone and on theaudio unit. Make sure the Bluetoothmenu option in the audio unit is set toON. For information on phone settings,refer to your phone user guide.
2. In the Bluetooth menu on your phone,search for Ford Audio and select it.
3. Enter the code number shown on thevehicle display using the phone keypad.If no code number is shown on thedisplay, enter the Bluetooth PINnumber 0000 using the phone keypad.Now enter the Bluetooth PIN numbershown on the vehicle display.
4. If your mobile phone asks you toauthorize the automatic connection,select YES.
Note: A phone call will be disconnected ifthe audio unit is switched off. If the ignitionkey is turned to the off position the phonecall will remain in progress.
196
Telephone
TELEPHONE CONTROLSRemote controlVoice and mode button
2
1
E87661
Voice button1Mode button2
Incoming calls can be accepted by pressingthe MODE button once. Press the buttonagain to end the call.
USING THE TELEPHONE -VEHICLES WITHOUT:NAVIGATION SYSTEMThis chapter describes the phone functionsof the audio unit.Note: Refer to your audio guide for detailsof the controls.An active phone must be present.Even if connected to the audio unit, yourphone can still be used in the usual way.Note: You can exit the phone menu bypressing any source button CD, AM/FM orAUX.
Making a callDialling a number using voice controlPhone numbers can be dialled using voicecontrol. See Telephone commands(page 212).
Dialling a number using the addressbookYou can access your phone address bookvia Bluetooth. The entries will appear inthe unit display.1. Press the PHONE or the call accept
button.2. Press the MENU button.3. Keep pressing the MENU button until
PHONEBOOK appears.4. Press the seek buttons to select the
desired phone number.Note: Press and hold the seek button toskip to the next letter in the alphabet.5. Press the PHONE or the call accept
button to dial the selected phonenumber.
Dialling a number using the addressbook - Sony radioYou can access your phone address bookvia Bluetooth. The entries will appear inthe unit display.1. Press the PHONE button.2. Press the seek button until the phone
book is shown.3. Press the up/down arrow buttons to
select the desired phone number.Note: Press and hold the up/down arrowbuttons to skip to the next letter in thealphabet.4. Press the PHONE or the call accept
button to dial the selected phonenumber.
197
Telephone
Dialling a number using the telephonekeypadIf you have an audio unit with a telephonekeypad (buttons 0-9, * and #):1. Press the call accept button. Press the
PHONE button if you have a Sonyradio.
2. Dial the number using the telephonekeypad on the audio unit.
3. Press the call accept button.Note: If you enter an incorrect digit whilstentering a phone number, press the seek leftbutton to erase the last digit. A long presswill erase the complete string of digits.Press and hold 0 to enter a + digit.
Ending a callCalls can be ended by pressing the callreject button.Audio units without a telephone keypadcan also end a call by pressing eitherPHONE, CD, AM/FM or ON/OFF, or bypressing the MODE button on the remotecontrol
Redialling a number1. Press the PHONE or the call accept
button.2. Press the MENU button.3. Select the CALL OUT list or the CALL
IN list. On some audio units, select theMISSED, INCOMING or OUTGOINGcalls list.
Note: If the active phone does not providea call out list, the last outgoing callnumber/entry can be redialled.4. Press the seek button on the audio unit.5. Press the PHONE or the call accept
button to dial the desired phonenumber.
Redialling a number - Sony radio1. Press the PHONE or the call accept
button.2. Press the seek button until the desired
list is displayed.Note: If the active phone does not providea call out list, the last outgoing callnumber/entry can be redialled.3. Press the up/down buttons to select
the desired phone number.4. Press the PHONE or the call accept
button to dial the phone number.
Redialling the last dialled number -Sony radio1. Press the call accept button.2. Press the call accept button a second
time to dial the number.
Receiving an incoming callAccepting an incoming callIncoming calls can be accepted by pressingeither the call accept button, the PHONEbutton or the MODE button on the remotecontrol.
Rejecting an incoming callIncoming calls can be rejected by pressingthe call reject button.Audio units without a telephone keypadcan also reject a call by pressing eitherPHONE, CD, AM/FM or ON/OFF.
Receiving a second incoming callNote: The second incoming call functionmust be activated in your phone.If there is an incoming call whilst there isan ongoing call, a beep will be heard andyou will have the option to end the activecall and to accept the incoming call.
198
Telephone
Accepting a second incoming callSecond incoming calls can be acceptedby pressing either the call accept button,the PHONE button, or the MODE buttonon the remote control.
Rejecting a second incoming callSecond incoming calls can be rejected bypressing the call reject button. Unitswithout a telephone keypad can also rejecta second incoming call by pressing the CDbutton, or the AM/FM button.
Muting the microphoneDuring a call, it is possible to mute themicrophone. Whilst muted, confirmationwill appear in the display.
Audio units with green call acceptbuttonPress the call accept button. Press thebutton once again to turn this function off.
Audio units without green call acceptbuttonPress the seek up or down button. Pressthe button once again to turn this functionoff.
Changing the active phoneNote: Phones must be bonded to thesystem before they can be made active.
Using the station storage buttonNote: This process is only for audio unitswithout a telephone keypad.1. Press the PHONE button on the audio
unit.2. Press the preset number required
(using the station preset buttons 1 - 6).
Using the audio unit menuNote: After bonding a phone to the system,this becomes the active phone.1. Press the PHONE or call accept
button.2. Press the MENU button on the audio
unit.3. Select the ACTIVE PHONE option on
the audio unit.4. Scroll through the different stored
phones by using the seek buttons todisplay the bonded phones.
5. Press the MENU button to select thephone which is to be the active phone.
Debonding a bonded phoneA bonded phone can be deleted from thesystem at any time, unless a phone call isin progress.1. Press the PHONE or call accept
button.2. Press the MENU button on the audio
unit.3. Select the DEBOND option on the
audio unit.4. Scroll through the different phones by
using the seek buttons and display thephone to be debonded.
5. Press the MENU button to select thephone which is to be debonded.
Debonding a bonded phone - SonyradioA bonded phone can be deleted from thesystem at any time, unless a phone call isin progress.1. Press the PHONE button.2. Press the up/down arrow buttons until
you reach the DEBOND option.
199
Telephone
3. Scroll through the different phones byusing the seek buttons and display thephone to be debonded.
4. Press the OK button to be debond.
USING THE TELEPHONE -VEHICLES WITH: NAVIGATIONSYSTEMThis chapter describes the phone functionsof the Navigation System.Note: Refer to your Navigation Systemguide for details of the controls.An active phone must be present.Even if connected to the NavigationSystem, your phone can still be used in theusual way.
Making a callDialling a numberPhone numbers can be dialled using voicecontrol. See Voice control (page 202).
Ending a callCalls can be ended by pressing either theEND button, the MODE button on theremote switch or the ON/OFF button onthe navigation system.
Redialling a number1. Press the PHONE button on the unit.2. Select REDIAL.
Receiving an incoming callAccepting an incoming callIncoming calls can be accepted by pressingeither the call accept button, the MODEbutton on the remote control, the PHONEbutton on the unit or by using the ACCEPToption in the menu.
Rejecting an incoming callIncoming calls can be rejected by pressingeither the call reject button, the CD orAM/FM buttons on the unit, or by usingthe REJECT option in the menu.
Receiving a second incoming callNote: The second incoming call functionmust be activated in your phone.If there is an incoming call, whilst there isan ongoing call, a beep will be heard andyou will have the option to end the activecall and to accept the incoming call.
Accepting a second incoming callSecond incoming calls can be acceptedby pressing either the call accept button,the MODE button on the remote control,the PHONE button on the unit or by usingthe ACCEPT option in the menu.Note: This will cancel the ongoing call.
Rejecting a second incoming callSecond incoming calls can be rejected bypressing either the call reject button, or oneof the following buttons on the unit: CD,AM/FM.
Muting the microphoneDuring a call, it is possible to mute themicrophone. Whilst muted, confirmationwill appear in the display.
SD navigation unitsPress the mute button (symbol of amicrophone with a line through it). Pressthe button once again to turn this functionoff.
CD navigation unitsPress the microphone mute button. Pressthe button once again to turn this functionoff.
200
Telephone
Changing the active phoneNote: Phones must be bonded to thesystem before they can be made active.Note: After bonding a phone to the system,this becomes the active phone.1. Press the PHONE button on the unit.2. Using the BT SETTINGS option in the
menu, select the active phone from thelist.
Debonding a bonded phoneA bonded phone can be deleted from thesystem at any time, unless a phone call isin progress.1. Press the PHONE button on the unit.2. Select the BT SETTINGS option in the
menu.3. Select the DEBOND option in the
menu.4. Select the phone from the list.
201
Telephone
PRINCIPLE OF OPERATION
CAUTIONUsing the system with the engine offwill drain the battery.
Voice recognition enables operation of thesystem without the need to divert yourattention from the road ahead in order tochange settings, or receive feedback fromthe system.Whenever you issue one of the definedcommands with the system active, thevoice recognition system converts yourcommand into a control signal for thesystem. Your inputs take the form ofdialogues or commands. You are guidedthrough these dialogues byannouncements or questions.Please familiarise yourself with thefunctions of the system before using voicerecognition.
Supported commandsThe voice control system allows you tocontrol the following vehicle functions:• Bluetooth phone• radio• CD Player/CD Changer• external device (USB)• external device (iPod)• automatic climate control• navigation system - refer to separate
navigation handbook).
System responseAs you work through a voice session thesystem will prompt you with a beep toneeach time the system is ready to proceed.
Do not try to give any commands until thebeep tone has been heard. The voicecontrol system will repeat each spokencommand back to you.If you are not sure how to continue say"HELP" for assistance or "CANCEL" if youdo not wish to continue.The "HELP" function provides only asubset of the available voice commands.Detailed explanations of all possible voicecommands can be found on the followingpages.
Voice commandsAll voice commands should be given usinga natural speaking voice, as if speaking toa passenger or on the phone. Your voicelevel should be dependant on thesurrounding noise level inside or outsidethe vehicle but do not shout.
USING VOICE CONTROLSystem operationThe order and content of the voice controlsare given in the following lists. The tablesshow the sequence of user voicecommands and system responses for eachavailable function.<> indicates a number or stored name tagto be inserted by the user.
Short cutsThere are a number of voice commandshort cuts available, which allow you tocontrol some vehicle features withouthaving to follow the complete commandmenu. These are:• phone: "MOBILE NAME", "DIAL
NUMBER", "DIAL NAME", and "REDIAL"• CD player/CD changer: "DISC" and
"TRACK"
202
Voice control
• automatic climate control:"TEMPERATURE", "AUTO MODE","DEFROSTING/DEMISTING ON" and"DEFROSTING/DEMISTING OFF"
• radio: "TUNE NAME"• external device (USB): "TRACK"• external device (iPod): "TRACK"• SD card: "TRACK".
Start communicating with the systemBefore you can start talking to the systemyou first have to press the VOICE or MODEbutton for each operation and wait untilthe system answers with a beep. SeeVoice Control (page 40).Press the button again to cancel the voicesession.
Name tagThe name tag functionality can supportthe phone, audio and navigation featuresby using the "STORE NAME" function. Youcan assign name tags to items such asfavourite radio stations and personalphone contacts. See Audio unitcommands (page 203). See Telephonecommands (page 212). See Navigationsystem commands (page 217).• Store up to 20 name tags per function.• The average recording time for each
name tag is approximately 2-3seconds.
AUDIO UNIT COMMANDSCD PlayerYou can control playback directly by voicecontrol.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"CD PLAYER"
"HELP"
"PLAY"
"TRACK"*
"SHUFFLE ALL"
"SHUFFLE FOLDER"**
"SHUFFLE OFF"
"REPEAT FOLDER"**
"REPEAT TRACK"
203
Voice control
"CD PLAYER"
"REPEAT OFF"
* Can be used as a shortcut.** Only available if the CD contains audio data files like MP3 or WMA.
TrackYou can choose a track on your CD directly.
System answerUser saysSteps
"CD PLAYER""CD PLAYER"1
"TRACK NUMBER PLEASE""TRACK"*2
"TRACK <number>""<a number between 1 and 99>"**3
* Can be used as a shortcut.** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)
Shuffle allTo set random playback.
System answerUser saysSteps
"CD PLAYER""CD PLAYER"1
"SHUFFLE ALL"2
CD ChangerOverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"CD CHANGER"
"HELP"
204
Voice control
"CD CHANGER"
"PLAY"
"DISC"*
"TRACK"*
"SHUFFLE ALL"
"SHUFFLE CD"
"SHUFFLE FOLDER"**
"SHUFFLE OFF"
"REPEAT CD"
"REPEAT FOLDER"**
"REPEAT TRACK"
"REPEAT OFF"
* Can be used as a shortcut.** Only available if the CD contains audio data files like MP3 or WMA.
DiscIf you have a CD changer you can choosethe disc number.
System answerUser saysSteps
"CD CHANGER""CD CHANGER"1
"DISC NUMBER PLEASE""DISC"*2
"DISC <number>""<a number between 1 and 6>"3
* Can be used as a shortcut.
TrackYou can choose a track on your CD directly.
205
Voice control
System answerUser saysSteps
"CD CHANGER""CD CHANGER"1
"TRACK NUMBER PLEASE""TRACK"*2
"TRACK <number>""<a number between 1 and 99>"**3
* Can be used as a shortcut.** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)
Shuffle CDTo set random playback within the CDcontents.
System answerUser saysSteps
"CD CHANGER""CD CHANGER"1
"SHUFFLE CD"2
RadioThe radio voice commands support thefunctionality of the radio and allow you totune radio stations by voice control.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu.
"RADIO"
"HELP"
"AM"
"FM"
"TUNE NAME"*
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
206
Voice control
"RADIO"
"PLAY"
* Can be used as a shortcut.
Tune frequencyThis function allows you to tune your radioby voice commands.
System answerUser saysSteps
"RADIO""RADIO"1
"AM FREQUENCY PLEASE""AM"2
"FM FREQUENCY PLEASE""FM"
"TUNE <frequency>""<frequency>"*3
* The frequency may be entered in a variety of ways. Refer below for representativeexamples.
FM band: 87.5 - 108.0 in increments of 0.1• "Eighty nine point nine" (89.9)• "Ninety" (90.0)• "One hundred point five" (100.5)• "One zero one point one" (101.1)• "One zero eight" (108.0)AM/MW band: 531 - 1602 in increments of9AM/LW band: 153 - 281 in increments of 1
• "Five thirty one" (531)• "Nine hundred" (900)• "Fourteen forty" (1440)• "Fifteen zero three" (1503)• "Ten eighty" (1080)
Store nameIf you have tuned a radio station, you canstore it with a name in the directory.
System answerUser saysSteps
"RADIO""RADIO"1
"STORE NAME""STORE NAME"2"NAME PLEASE"
"REPEAT NAME PLEASE""<name>"3
"STORING NAME""<name>"4"<name> STORED"
207
Voice control
Tune name This function allows you to call up a storedradio station.
System answerUser saysSteps
"RADIO""RADIO"1
"NAME PLEASE""TUNE NAME"*2
"TUNE <name>""<name>"3
* Can be used as a shortcut.
Delete nameThis function allows you to delete a storedradio station.
System answerUser saysSteps
"RADIO""RADIO"1
"NAME PLEASE""DELETE NAME"2
"DELETE <name>""<name>"3"CONFIRM YES OR NO"
"DELETED""YES"4
"COMMAND CANCELLED""NO"
Play directoryThis function allows you to let the systemtell you all of the stored radio stations.
System answerUser saysSteps
"RADIO""RADIO"1
"PLAY <DIRECTORY>""PLAY DIRECTORY"2
Delete directoryThis function allows you to delete allstored radio stations at once.
208
Voice control
System answerUser saysSteps
"RADIO""RADIO"1
"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"
"RADIO DIRECTORY DELETED""YES"3
"COMMAND CANCELLED""NO"
PlayThis function switches the audio source tothe radio mode.
System answerUser saysSteps
"RADIO""RADIO"1
"PLAY"2
Auxiliary inputThis function allows you to switch theaudio source to the attached auxiliary inputdevice.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"LINE IN""LINE IN"2
External devices - USBThese voice commands support thefunctionality of an external USB devicewhich may be connected to the audio unit.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"EXTERNAL DEVICE", "USB"
"HELP"
209
Voice control
"EXTERNAL DEVICE", "USB"
"PLAY"
"TRACK"*
"PLAYLIST"**
"FOLDER"**
"SHUFFLE ALL"
"SHUFFLE FOLDER"
"SHUFFLE PLAYLIST"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT FOLDER"
"REPEAT OFF"
* Can be used as a shortcut.** Playlists and folders activated by voice control must be assigned special filenames.See General Information (page 220).
USB playThis function allows you to switch theaudio source to the attached USB device.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"USB""USB"2
"PLAY"3
USB TrackYou can choose a track on your USB devicedirectly.
210
Voice control
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"USB""USB"2
"TRACK NUMBER PLEASE""TRACK"3
"TRACK <number>""<a number between 1 and 99>"*4
* Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)
External devices - iPodThese voice commands support thefunctionality of an iPod which may beconnected to the audio unit.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"EXTERNAL DEVICE", "IPOD"
"HELP"
"PLAY"
"TRACK"*
"PLAYLIST"**
"SHUFFLE ALL"
"SHUFFLE PLAYLIST"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT OFF"
* Can be used as a shortcut.** Playlists activated by voice control must be assigned special filenames. See GeneralInformation (page 220).
211
Voice control
iPod Track You can choose a track off the all titles listof your iPod directly.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"IPOD""IPOD"2
"TRACK NUMBER PLEASE""TRACK"*3
"TRACK <number>""<a number between 1 and 99>"**4
* Can be used as a shortcut.** Additionally, numbers can be spoken as up to five single digits (for example "5", "2","4", "5", "3" for track 52453), to a limit of 65535.
iPod playlistYou can choose a playlist from your iPoddirectly.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"IPOD""IPOD"2
"PLAYLIST NUMBER PLEASE""PLAYLIST"*3
"PLAYLIST <number>""<a number between 1 and 10>"4
* Playlists activated by voice control must be assigned special filenames. See GeneralInformation (page 220).
TELEPHONE COMMANDSPhoneYour phone system allows you to createan additional phonebook. The storedentries can be dialled by voice control.Phone numbers stored by using voicecontrol are stored on the vehicle systemand not in your phone.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
212
Voice control
"PHONE"
"HELP"
"MOBILE NAME"*
"DIAL NUMBER"*
"DIAL NAME"*
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
"REDIAL"*
"ACCEPT CALLS"
"REJECT CALLS"
* Can be used as a shortcut.
Phone functionsDial numberPhone numbers can be dialled after givingthe name tag voice command.
System answerUser saysSteps
"PHONE""PHONE"1
"NUMBER PLEASE""DIAL NUMBER"*2
"<phone number>"<phone number>"3CONTINUE?"
"DIALLING""DIAL"4
"<repeat last part of number>"CORRECTION"CONTINUE?"
* Can be used as a shortcut.
213
Voice control
Dial name Phone numbers can be dialled after givingthe name tag voice command.
System answerUser saysSteps
"PHONE""PHONE"1
"NAME PLEASE""DIAL NAME"*2
"DIAL <name>""<name>"3"CONFIRM YES OR NO"
"DIALLING""YES"4
"COMMAND CANCELLED""NO"
* Can be used as a shortcut.
RedialThis function allows you to redial the lastdialled phone number.
System answerUser saysSteps
"PHONE""PHONE"1
"REDIAL""REDIAL"*2"CONFIRM YES OR NO"
"DIALLING""YES"3
"COMMAND CANCELLED""NO"
* Can be used as a shortcut.
Mobile nameThis function allows you to access phonenumbers stored with a name tag in yourmobile phone.
System answerUser saysSteps
"PHONE""PHONE"1
"MOBILE NAME" "<phonedependent dialogue>""MOBILE NAME"*2
* Can be used as a shortcut.
214
Voice control
DTMF (Tone dialling)This function transfers spoken numbersinto DTMF tones. For example, to make aremote enquiry to your home answeringmachine or to enter a PIN number etc.
Note: DTMF can only be used during anongoing call. Operate the VOICE button andwait for the system prompt.Can only be used with vehicles installed witha dedicated VOICE button.
System answerUser saysSteps
"NUMBER PLEASE"1
"<numbers 1 to 9, zero, hash, star>"2
Create a phonebookStore nameNew entries can be stored with the"STORE NAME" command. This featurecan be used to dial a number by calling upthe name instead of the full phone number.
System answerUser saysSteps
"PHONE""PHONE"1
"STORE NAME""STORE NAME"2"NAME PLEASE"
"REPEAT NAME PLEASE""<name>"3
"STORING NAME""<name>"4"<name> STORED""NUMBER PLEASE"
"<phone number>""<phone number>"5
"STORING NUMBER""STORE"6"<phone number>""NUMBER STORED"
Delete nameStored names can also be deleted fromthe directory.
215
Voice control
System answerUser saysSteps
"PHONE""PHONE"1
"NAME PLEASE""DELETE NAME"2
"DELETE <name>""<name>"3"CONFIRM YES OR NO"
"<name> DELETED""YES"4
"COMMAND CANCELLED""NO"
Play directoryUse this function to let the system tell youall stored entries.
System answerUser saysSteps
"PHONE""PHONE"1
"PLAY DIRECTORY""PLAY DIRECTORY"2
Delete directoryThis function allows you to delete allentries in one go.
System answerUser saysSteps
"PHONE""PHONE"1
"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"
"DIRECTORY DELETED""YES"3
"COMMAND CANCELLED""NO"
Main settingsReject callsCalls can be set to be automaticallyrejected using voice control.
216
Voice control
System answerUser saysSteps
"PHONE""PHONE"1
"REJECT CALLS""REJECT CALLS"2
"ACCEPT CALLS""ACCEPT CALLS"*
* use this command to turn the reject mode off
NAVIGATION SYSTEMCOMMANDSPlease refer to your separate Navigationmanual for details of the command menus.
CLIMATE CONTROLCOMMANDSClimateThe climate voice commands supports thefunctionality of the fan speed, temperatureand mode settings. Not all functions areavailable on all vehicles.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"CLIMATE"
"HELP"
"FAN"*
"DEFROSTING/DEMISTING ON"*
"DEFROSTING/DEMISTING OFF"*
"TEMPERATURE"*
"AUTO MODE"*
* Can be used as a shortcut. On vehicles fitted with an English language module the "FAN"shortcut is not available.
217
Voice control
Fan This function allows you to adjust the fanspeed.
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"FAN SPEED PLEASE""‘FAN"*2
"FAN MINIMUM""MINIMUM"
3 "FAN <number>""<a number between 1 and 7>"
"FAN MAXIMUM""MAXIMUM"
* Can be used as a shortcut. On vehicles fitted with an English language module the "FAN"shortcut is not available.
Defrosting/Demisting
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"DEFROSTING ON/DEMISTING ON""DEFROSTING ON/DEMISTING
ON"*
2"DEFROSTING OFF/DEMISTING
OFF""DEFROSTING OFF/DEMISTING
OFF"*
* Can be used as a shortcut.
TemperatureThis function allows you to adjust thetemperature.
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"TEMPERATURE PLEASE""TEMPERATURE"*2
"TEMPERATURE MINIMUM""MINIMUM"
3"TEMPERATURE <number>"
"<a number between 15 and 29 °Cwith 0.5 increments>" or "<a
number between 59 and 84 °F>"
218
Voice control
System answerUser saysSteps
"TEMPERATURE MAXIMUM""MAXIMUM"
* Can be used as a shortcut.
Auto mode
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"AUTO MODE""AUTO MODE"*2
* Can be used as a shortcut. Can be deactivated by selecting a different temperature orfan speed.
219
Voice control
GENERAL INFORMATION
CAUTIONSTake care when handling externaldevices with exposed electricalconnectors (such as the USB plug).
Always replace the protective cap/shieldwhen possible. There may be a risk ofelectrostatic discharge causing damageto the device.
Do not touch or handle the USBsocket in the vehicle. Cover the socketwhen not in use.Only use USB Mass-Storage devicecompliant devices.Always switch your audio unit to adifferent source (for example theradio) before unplugging the USB
device.Do not install or connect USB hubs orsplitters.
Note: The system is only designed torecognize and read suitable audio files froma USB device that conforms to the USBMass-Storage device class or an iPod. Notall available USB devices can be guaranteedto function with the system.Note: It is possible to connect compatibledevices with a trailing USB lead as well asthose that plug into the vehicle USB socketdirectly (for example USB memory sticksand pen drives).Note: Some USB devices with a higherpower consumption may not be compatible(for example some larger hard drives).Note: Access time to read the files on theexternal device will vary depending uponfactors such as the file structure, size anddevice content.
The system supports a range of externaldevices, to fully integrate with your audiounit via the USB and auxiliary inputsockets. Once connected, control of theexternal device is possible via the audiounit.A list of typical compatible devices areshown below:• USB memory sticks• USB portable hard drives• Some MP3 players with USB
connection• iPod media players (refer to
www.ford-mobile-connectivity.com for latestcompatibility list).
The system is USB 2.0 full speedcompatible, USB 1.1 host compliant andsupports FAT 16/32 file systems.
Information on audio filestructures for external devicesUSBCreate only a single partition on the USBdevice.If playlists are created, they must containcorrect file paths referenced to the USBdevice. It is recommended to create theplaylist after the audio files have beentransferred to the USB device.Playlists must be created in .m3u format.Audio files must be in .mp3 format.Do not exceed the following limits:• 1000 items per folder (files, folders and
playlists)• 5000 folders per USB device (including
playlists)• 8 subfolder levels.
220
Connectivity
To enable voice control for customplaylists and folders, follow the procedurebelow:• Create folders named with the
structure "Ford<*>" where <*> is anumber 1-10. For example "Ford3"without an extension.
• Create playlists named with thestructure "Ford<*>.m3u" where <*>is a number 1-10. For example"Ford5.m3u" without any spacebetween "Ford" and the number.
Thereafter, custom folders and playlistswill be selectable with voice control. SeeAudio unit commands (page 203).
iPodTo enable voice control for customplaylists, create playlists named with thestructure "Ford<*>" where <*> is anumber 1-10. For example "Ford7" withoutany space between "Ford" and thenumber.Thereafter, playlists will be selectable withvoice control. See Audio unit commands(page 203).
CONNECTING AN EXTERNALDEVICE
WARNINGMake sure the external device issecurely mounted within the vehicle,and that trailing connections do not
obstruct any of the driving controls.
External devices may be connected usingthe auxiliary input socket and the USB port.See Auxiliary input (AUX IN) socket(page 96). See USB port (page 97).
ConnectionPlug in the device, and if necessary secureit to prevent movement within the vehicle.
Connecting an iPodFor optimum convenience and audioquality, we recommend that you purchasea dedicated single connection leadavailable from your dealer.Alternatively, it is possible to connect youriPod using the standard iPod USB cableand a separate 3.5mm audio jack lead. Ifusing this method preset the iPod volumeto maximum and turn off any equalizersettings before making the connections:• Connect the headphone output of the
iPod to the AUX IN socket.• Connect the USB cable from the iPod
to the vehicle USB socket.
CONNECTING AN EXTERNALDEVICE - VEHICLES WITH:BLUETOOTHConnecting a Bluetooth audiodevice
CAUTIONAs various standards exist,manufacturers are able to implementa variety of profiles in their Bluetooth
devices. Because of this, an incompatibilitycan occur between the Bluetooth deviceand the system, which in some cases maylimit system functionality. To avoid thissituation, only recommended devicesshould be used.
Please visit the websitewww.ford-mobile-connectivity.comfor full details.
221
Connectivity
Bonding the deviceNote: Some audio and navigation unitshave a separate Bluetooth audio menu. Usethis to access setup and control.To connect the device to the system followthe same procedure as for Bluetooth handsfree phones. See Bluetooth setup (page196).
Operating the deviceSelect Bluetooth audio as the activesource.Tracks can be accessed by skippingforwards and backwards using the steeringwheel controls, or directly from the audiounit controls.
USING A USB DEVICEVarious icons are used to identify types ofaudio file, folders etc.
E100029
USB device is the active source
E100022
Folder
E100023
Playlist
E100024
Album
E100025
Artist
E100026
Filename
E100027
Track title
E100028
Information not available
Sony radioOperationSelect the USB device as the audio sourceby repeatedly pressing the CD/AUXbutton until USB appears in the display.After first connecting the USB device, thefirst track within the first folder will startto play automatically. Subsequently,following audio source switching, theposition of playback on the USB device isremembered.To browse the device contents, press theup/down arrow key or the OK button once.The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the folder view.
• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).
• "<" before the list indicates that afurther level up is readable.
• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.
To navigate the USB device contents, usethe up/down arrow keys to scroll throughlists, and the left/right keys to move up ordown within the folder hierarchy. Once yourdesired track, playlist or folder ishighlighted, press the OK button to selectplayback.Note: If you wish to jump to the top levelof the USB device contents, press and holdthe left arrow key.
222
Connectivity
Audio controlPress the left and right arrow keys to skipbackwards and forwards through tracks.Press and hold the left/right arrow keys toenable fast rewind/fast forward throughtrack content.Press the up/down arrow key or the OKbutton to browse the device contents.Press the MENU key to enter the USBmenu. It is possible to enable shuffle andrepeat functions here with respect tofolders and playlists.Press the SCAN button to scan the wholedevice, current folder or a playlist if it is inoperation.Press the INFO button to display thefollowing:• filename• title• artist• album• track number and playing time.Repeated button presses will scrollthrough these displays.
CD Navigation unitsOperationSelect the USB device as the audio sourceby pressing the CD/AUX button untilDEVICES appears in the display. SelectDEVICES and then select USB from theavailable device list. After first connectingthe USB device, the first track within thefirst folder will start to play automatically.Subsequently, following audio sourceswitching, the position of playback on theUSB device is remembered.To browse the device contents, press theSELECT button once.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the folder view.
• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).
• "<" to the left hand side of the displayindicates that a further level up isreadable.
• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.
To navigate the USB device contents, usethe rotary scroll/select button to browsethrough lists. Push the button to expandthe contents within the highlighted playlistor folder, or to commence playback of aparticular track. Press ESC to go up onelevel.
Audio controlPress the SEEK up and down keys to skipbackwards and forwards through tracks.Press and hold the SEEK keys to enablefast rewind/fast forward through trackcontent.Rotate or press the SELECT button tobrowse the device contents.Press SHUFFLE or REPEAT buttons toenable shuffle and repeat functions withrespect to folders and playlists. Differentoptions may appear depending uponwhether or not a playlist is in operation.Press the SCAN button to scan the currentplaylist if it is in operation, or the completeUSB device or folder.
223
Connectivity
Press the INFO button to display thefollowing:• filename• title• artist• album• track number and playing time.
SD Navigation unitsOperationSelect the USB device as the audio sourceby pressing the CD/AUX button until theUSB button appears to the left of thedisplay. Select USB from the availabledevice list.Note: Some devices may be shown but notselectable, depending if the device isconnected or not.After first connecting the USB device, thefirst track within the first folder will startto play automatically. Subsequently,following audio source switching, theposition of playback on the USB device isremembered.To browse the device contents, press thescroll up or down arrow button.The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the folder view.
• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).
• "<" to the left hand side of the displayindicates that a further level up isreadable.
• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.
To navigate the USB device contents, usethe scroll buttons to browse through lists.Push the button to expand the contentswithin the highlighted playlist or folder, orto commence playback of a particulartrack. Press the left arrow key to go up onelevel.
Audio controlPress the SEEK up and down keys to skipbackwards and forwards through tracks.Press and hold the SEEK keys to enablefast rewind/fast forward through trackcontent.Press the scroll bar arrow keys to browsethe device contents.Press SHUFFLE or REPEAT buttons toenable shuffle and repeat functions withrespect to folders and playlists.Press the SCAN button to scan the currentplaylist if it is in operation, or the completeUSB device or folder.Press the INFO button to display thefollowing:• filename• title• artist• album• track number and playing time.
USING AN IPODVarious icons are used to identify types ofaudio file, folders etc.
224
Connectivity
E100030
iPod is the active source
E100031
iPod playlist
E100032
iPod artist
E100033
iPod album
E100034
iPod genre
E100035
iPod song
E100036
iPod generic category
E100037
iPod generic media file
Sony radioOperationConnect the iPod. See Connecting anexternal device (page 221).Select the iPod as the audio source byrepeatedly pressing the CD/AUX buttonuntil iPod appears in the display.The iPod menu list for browsing contentswill be available through the radio display.Navigation of the contents follows thesame principles as for iPod standalone use(for example search by artist, title, etc.).To browse the iPod contents, press theup/down arrow key or the OK button once.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the list view.
• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).
• "<" before the list indicates that afurther level up is readable.
• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.
To navigate the iPod contents, use theup/down arrow keys to scroll through lists,and the left/right keys to move up or downwithin the hierarchy. Once your desiredtrack, playlist, album, artist or genre ishighlighted, press the OK button to selectplayback.Note: If you wish to jump to the top levelof the iPod contents, press and hold the leftarrow key.
Audio controlPress the left and right arrow keys to skipbackwards and forwards through tracks.Press and hold the left/right arrow keys toenable fast rewind/fast forward throughtrack content.Press the up/down arrow key or the OKbutton to browse the iPod contents.Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possible toenable the iPod "Shuffle songs" optiondirectly from the top level.Press the SCAN button to scan thecurrently selected tracks.
225
Connectivity
Press the INFO button to display thefollowing:• title• artist• track number and playing time.Repeated button presses will scrollthrough these displays.
CD Navigation unitsOperationConnect the iPod. See Connecting anexternal device (page 221).Select the iPod as the audio source bypressing the CD/AUX button untilDEVICES appears in the display. SelectDEVICES and then select iPod from theavailable device list.The iPod menu list for browsing contentswill be available through the display.Navigation of the contents follows thesame principles as for iPod standalone use(for example search by artist, title, etc.).To browse the iPod contents, press theSELECT button once.The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the list view.
• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).
• "<" before the list indicates that afurther level up is readable.
• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.
To navigate the iPod contents, use therotary scroll/select button to browsethrough lists. Push the button to expandthe contents within the highlighted playlist,album, artist, genre or to commenceplayback of a particular track. Press ESCto go up one level.
Audio controlPress the SEEK up and down keys to skipbackwards and forwards through tracks.Press and hold the SEEK keys to enablefast rewind/fast forward through trackcontent.Rotate or press the SELECT button tobrowse the iPod contents.Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possible toenable the iPod "Shuffle songs" optiondirectly from the top level.Press the SCAN button to scan thecurrently selected tracks.Press the INFO button to display thefollowing:• title• artist• track number and playing time.
SD Navigation unitsOperationConnect the iPod. See Connecting anexternal device (page 221).Select the iPod as the audio source bypressing the CD/AUX button until the iPodbutton appears to the left of the display.Select iPod from the available device list.Note: Some devices may be shown but notselectable, depending if the device isconnected or not.
226
Connectivity
The iPod menu list for browsing contentswill be available through the display.Navigation of the contents follows thesame principles as for iPod standalone use(for example search by artist, title, etc.).To browse the iPod contents, press thescroll up or down arrow button.The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the list view.
• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).
• "<" before the list indicates that afurther level up is readable.
• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.
To navigate the iPod contents, use thescroll buttons to browse through lists. Pushthe button to expand the contents withinthe highlighted playlist, album, artist, genreor to commence playback of a particulartrack. Press the left arrow key to go up onelevel.
Audio controlPress the SEEK up and down keys to skipbackwards and forwards through tracks.Press and hold the SEEK keys to enablefast rewind/fast forward through trackcontent.Press the scroll bar arrow keys to browsethe iPod contents.Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possible toenable the iPod "Shuffle songs" optiondirectly from the top level.
Press the SCAN button to scan thecurrently selected tracks.Press the INFO button to display thefollowing:• title• artist• track number and playing time.
227
Connectivity
ROAD SAFETY
WARNINGSThe system provides you withinformation designed to help youreach your destination quickly and
safely.For reasons of safety, the drivershould only program the systemwhen the vehicle is stationary.The system provides no assistancewith respect to stop signs, trafficlights, areas under construction or
other important safety information.Do not use the system until you havefamiliarised yourself with itsoperation.Only view the system display whendriving conditions permit.
Safety informationRead and follow all stated safetyprecautions. Failure to do so may increaseyour risk of collision and personal injury.Ford Motor Company shall not be liablefor any damages of any type arising fromfailure to follow these guidelines.If detailed viewing of route instructions isnecessary, pull off the road when it is safeto do so and park your vehicle.Do not use the navigation system to locateemergency services.To use the system as effectively and safelyas possible, always use the latestnavigation information. Your dealer will beable to assist with this.
228
Navigation introduction
GETTING STARTED
CAUTIONUsing the system with the engine offwill drain the battery.
Note: You will be charged when sendingand receiving text messages.Note: Refer to your phone handbook for allphone functions and operation.Note: Keep the activation code (printed onthe installation guide) in a safe place.Note: Retain the activation text messagein your mobile phone inbox.
Compatibility of phonesCAUTION
As no common agreement exists,mobile phone manufacturers are ableto implement a variety of profiles in
their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insome cases may significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.
Please visit the websitewww.ford-mobile-connectivity.com forfull details.
Installing the micro SD card
1
2
E114212
1. Remove the micro SD card from theadaptor.
2. Insert the micro SD card into the mobilephone.
Activating the mobile phonenavigation systemNote: The radio must be switched on beforeconnecting the mobile phone to the in-carGPS receiver.Note: The Ford Mobile Navigation must beinstalled and activated on your mobilephone.Note: It is possible to activate up to amaximum of three phones.Note: Detailed instructions are availableon the micro SD card and atwww.ford-mobile-connectivity.com.To connect the device to the system followthe same procedure as for Bluetooth handsfree phones. See Bluetooth setup (page196).1. Switch the radio on.
229
Navigation system
E114213
2. Switch your mobile phone on and startthe "Ford Mobile Navigation".
3. Choose "Select Destination".4. Choose "Enter Address".5. Change route options if necessary and
start the route guidance.6. The vehicle display will show the turn
information. Voice instructions areheard via the vehicle speakers.
Note: Your mobile phone will display yourcurrent position.7. You are able to exit the application and
continue your route guidance afterrestarting the application.
230
Navigation system
TYPE APPROVALSFCC/INDUSTRY CANADA NOTICEThis device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) this devicemay not cause harmful interference, and(2) this device must accept anyinterference received, includinginterference that may cause undesiredoperation.FCC ID: WJLRX-42IC: 7847A-RX42Changes or modifications to your devicenot expressly approved by the partyresponsible for compliance can void theuser's authority to operate the equipment.
RX-42 - declaration of conformityWe, the party responsible for compliance,declare under our sole responsibility thatthe Handset Integration product RX-42 isin conformity with the provisions of thefollowing Council Directive: 1999/5/EC. Acopy of the Declaration of Conformity canbe found at:
www.novero.com/declaration_of_conformityThe Bluetooth word mark and logos areowned by the Bluetooth SIG, Inc. and anyuse of such marks by Ford Motor Companyis under license. Other trademarks andtrade names are those of their respectiveowners.
TYPE APPROVALSiPod is a trademark of Apple Inc.
TYPE APPROVALS
E114214
© 2008 NAVTEQ B.V. All rights reserved.
231
Appendices
E114220
ELECTROMAGNETICCOMPATIBILITY
WARNINGSYour vehicle has been tested andcertified to legislations relating toelectromagnetic compatibility
(72/245/EEC, UN ECE Regulation 10 orother applicable local requirements). It isyour responsibility to ensure that anyequipment you have fitted complies withapplicable local legislations. Have anyequipment fitted by properly trainedtechnicians.
WARNINGSThe RF (radio frequency) transmitterequipment (e.g. cellular telephones,amateur radio transmitters etc.) may
only be fitted to your vehicle if they complywith the parameters shown in the tablebelow. There are no special provisions orconditions for installations or use.
Do not mount any transceiver,microphones, speakers, or any otheritem in the deployment path of the
airbag system.Do not fasten antenna cables tooriginal vehicle wiring, fuel pipes andbrake pipes.
232
Appendices
WARNINGSKeep antenna and power cables atleast 10 centimetres (4 inches) from
WARNINGSany electronic modules and airbags.
E85998
1 2 3 4
Antenna PositionsMaximum output power Watt (PeakRMS)
Frequency BandMHz
3, 450 W1 – 30
1, 2, 350 W30 – 54
1, 2, 350 W68 – 87.5
1, 2, 350 W142 – 176
1, 2, 350 W380 – 512
1, 2, 310 W806 – 940
1, 2, 310 W1200 – 1400
1, 2, 310 W1710 – 1885
1, 2, 310 W1885 – 2025
Note: After the installation of RFtransmitters, check for disturbances fromand to all electrical equipment in thevehicle, both in the standby and transmitmodes.
Check all electrical equipment:• with the ignition ON• with the engine running• during a road test at various speeds.
233
Appendices
Check that electromagnetic fieldsgenerated inside the vehicle cabin by thetransmitter installed do not exceedapplicable human exposure requirements.
234
Appendices
AA/C
See: Climate Control..........................................80About This Manual...........................................7ABS
See: Brakes.............................................................112ABS driving hints
See: Hints on Driving With Anti-LockBrakes..................................................................112
AccessoriesSee: Parts and Accessories.................................7
Adaptive Headlamps...................................48Adjusting the Steering Wheel...................39AFS
See: Adaptive Headlamps................................48Air Conditioning
See: Climate Control..........................................80Air Vents............................................................80Alarm...................................................................37All-Wheel Drive...............................................111Alternative frequencies..............................186
All except Sony and Sony DAB.....................186Sony and Sony DAB..........................................186
Appendices.....................................................231Arming the alarm............................................37
Automatic arming delay....................................37Interior sensors......................................................37
Arming the engine immobiliser................36At a Glance........................................................10
Adjusting the steering wheel............................14Airbag........................................................................16Autolamps...............................................................15Automatic climate control.................................15Autowipers..............................................................16Direction indicators...............................................15Instrument panel overview...............................10Keyless entry...........................................................13Keyless starting......................................................14Locking and unlocking.........................................12Manual climate control.......................................15Manual transmission...........................................16Towing the vehicle on four wheels.................16
Audible Warnings and Indicators.............65Automatic transmission....................................65Frost..........................................................................65Key-in-ignition.......................................................65Key outside car......................................................65Lights on..................................................................66Low fuel...................................................................66Seat belt reminder...............................................66
Audio Control...................................................39Mode.........................................................................40Seek..........................................................................40Volume.....................................................................39
Audio distortion reduction (CLIP)..........185All except Sony and Sony DAB.....................185Sony and Sony DAB...........................................185
Audio introduction........................................173Audio menu control.....................................179
Sony CD and Sony CD DAB withBluetooth...........................................................181
Audio system security..................................177Audio troubleshooting...............................194Audio unit clock and date displays........178Audio unit commands...............................203
Auxiliary input.....................................................209CD Changer.........................................................204CD Player..............................................................203External devices - iPod......................................211External devices - USB....................................209Radio......................................................................206
Audio unit menus.........................................185Audio unit operation....................................179Audio unit overview......................................174Auto-Dimming Mirror....................................61Autolamps........................................................46Automatic Climate Control........................83
Air distribution.......................................................84Blower......................................................................84Mono mode............................................................83Recirculated air.....................................................85Setting the temperature....................................83Switching off the automatic climate
control.................................................................85Switching the air conditioning on and
off..........................................................................84To switch mono mode back on......................84To switch mono mode off................................84Windscreen defrosting and demisting........84
235
Index
Automatic Transmission...........................108Emergency park position release
lever.....................................................................110Hints on driving with an automatic
transmission...................................................109Manual shifting - Vehicles with a 5 speed
transmission...................................................109Selector lever positions...................................108Sport mode and manual shifting - Vehicles
with a 6 speed transmission.....................109Automatic volume control........................185
All except Sony and Sony DAB.....................185Sony and Sony DAB...........................................185
Autostore control.........................................1826000CD.................................................................182Sony CD..................................................................182
Autowipers........................................................41Auxiliary Heater..............................................85
Diesel auxiliary heater (depending oncountry)..............................................................88
Fuel operated heater (depending oncountry)..............................................................88
Parking heater.......................................................85Auxiliary input (AUX IN) socket................96Auxiliary Power Points.................................94
Power inverter.......................................................94AWD
See: All-Wheel Drive............................................111
BBalance/fade control..................................179
All except Sony and Sony DAB .....................179Sony and Sony DAB...........................................179
Bass/treble control......................................179All except Sony and Sony DAB......................179Sony and Sony DAB...........................................179
Bluetooth setup............................................196Handling of phones...........................................196Requirements for Bluetooth
connection.......................................................196Bonnet Lock
See: Opening and Closing the Bonnet........141Booster cables
See: Jump-Starting the Vehicle.....................153Booster Seats..................................................20
Booster cushion (Group 3)................................21Booster seat (Group 2)......................................20
Brake and Clutch Fluid Check..................147Brakes.................................................................112
Principle of Operation........................................112Bulb changing
See: Changing a Bulb...........................................51Bulb Specification Chart..............................57
CCapacities and Specifications.................170
Technical Specifications..................................170Car Wash
See: Cleaning the Exterior................................151Catalytic Converter......................................105
Driving with a catalytic converter.................105CD changer.......................................................96Changing a Bulb..............................................51
Approach lamp.....................................................53Central high mounted brake lamp.................55Daytime running lamps......................................52Front fog lamps.....................................................53Headlamp................................................................51Interior lamp...........................................................55Luggage compartment lamp...........................57Number plate lamp.............................................55Reading lamps......................................................56Rear fog lamps......................................................54Rear lamps..............................................................54Side repeaters........................................................52Vanity mirror lamp...............................................56
Changing a Fuse............................................133Changing a Road Wheel............................155
Assembling the wheel brace..........................157Installing a road wheel.....................................159Jacking and lifting points.................................156Locking wheel nuts............................................155Removing a road wheel...................................158Removing the wheel trim................................158Vehicle jack...........................................................155Vehicles with a temporary spare
wheel..................................................................155Changing the remote control
battery.............................................................28Changing the Wiper Blades.......................43
Rear window wiper blade.................................44Windscreen wiper blades..................................43
Checking the Wiper Blades........................43Child Safety........................................................17
236
Index
Child Safety Locks..........................................22Left-hand side.......................................................22Right-hand side.....................................................22
Child Seat Positioning...................................18......................................................................................18
Child Seats.........................................................17Child restraints for different mass
groups...................................................................17Cigar Lighter.....................................................94Cleaning the Exterior....................................151
Body paintwork preservation..........................151Cleaning the chrome trim.................................151Cleaning the headlamps...................................151Cleaning the rear window.................................151
Cleaning the Interior.....................................151Instrument cluster screens, LCD screens,
radio screens....................................................152Rear windows.......................................................152Seat belts................................................................151
Climate Control..............................................80Principle of Operation........................................80
Climate control commands......................217Climate....................................................................217
Coded keys.......................................................36Cold Weather Precautions........................130Compact disc playback.............................189
6000CD.................................................................189Compact disc changer playback..................189Sony and Sony CD DAB...................................189
Compact disc player...................................188Compact disc track compression..........190
All except Sony and Sony DAB.....................190Sony and Sony DAB..........................................190
Compact disc track scanning...................1916000CD..................................................................191Sony and Sony DAB............................................191
Connecting an external device................221Connection............................................................221
Connecting an external device - VehiclesWith: Bluetooth..........................................221Connecting a Bluetooth audio device.........221
Connectivity...................................................220General Information.........................................220
Convenience features...................................93Coolant Check
See: Engine Coolant Check.............................147Cruise Control.................................................119
Principle of Operation........................................119
Cruise controlSee: Using Cruise Control.................................119
Cup Holders......................................................93Seat back trays.....................................................93
DDaytime Running Lamps.............................45Diesel Particulate Filter...............................101
Regeneration.........................................................101Digital signal processing (DSP)..............185
Changing the DSP settings.............................185DSP equaliser......................................................185DSP occupancy...................................................185
Direction Indicators.......................................49Disabling the passenger airbag................26
Disabling the passenger airbag......................26Enabling the passenger airbag........................27Fitting the passenger airbag deactivation
switch..................................................................26Disarming the alarm......................................37
Britain and Ireland only......................................38Disarming the engine immobiliser...........36DPF
See: Diesel Particulate Filter...........................101Driving Hints...................................................130Driving Through Water...............................130
Driving through water ......................................130DRL
See: Daytime Running Lamps.........................45
EEjecting compact discs...............................191
6000CD..................................................................191Sony CD...................................................................191
Electric exterior mirrors.................................61Electric folding mirrors........................................61Mirror tilting positions..........................................61
Electromagnetic compatibility...............232Ending compact disc playback...............192
All except Sony and Sony DAB......................192Sony and Sony DAB...........................................192
Engine Coolant Check.................................147Checking the coolant level..............................147Topping up.............................................................147
Engine immobiliser........................................36Principle of Operation........................................36
237
Index
Engine Oil Check...........................................146Checking the oil level........................................146Topping up............................................................146
Engine Oil Dipstick - 2.0L Duratorq-TDCi(DW) Diesel.................................................146
Engine Oil Dipstick - 2.5L Duratec(VI5)...............................................................146
Entering a security code..............................1776000CD, Sony and Sony DAB........................177
Exterior Mirrors...............................................60Manual folding mirrors......................................60
FFastening the seat belts..............................25Fast forward/reverse...................................189
All except Sony and Sony DAB.....................189Sony and Sony DAB..........................................189
First Aid Kit.......................................................131Floor Mats.........................................................98Fog Lamps - Front
See: Front Fog Lamps........................................46Fog Lamps - Rear
See: Rear Fog Lamps..........................................46Front Fog Lamps............................................46Fuel and Refuelling......................................103
Technical Specifications.................................106Fuel Burning Heater
See: Auxiliary Heater...........................................85Fuel Consumption.......................................105Fuel Consumption
See: Technical Specifications.......................106Fuel Cut-Off Switch.....................................132
Vehicles with a Duratec engine.....................132Fuel filler flap.................................................103
Refuelling with a fuel can...............................105Fuel Quality - Diesel....................................103
Long-term storage.............................................103Fuel Quality - Petrol....................................103Fuse Box Locations......................................133
Engine compartment fuse box......................133Passenger compartment fuse box...............133
Fuses.................................................................133Fuse Specification Chart...........................134
Engine compartment fuse box......................134Passenger compartment fuse box..............136
GGauges...............................................................62
Engine coolant temperature gauge..............62Fuel gauge..............................................................63
GearboxSee: Transmission..............................................108
General Information on RadioFrequencies...................................................28
Getting started.............................................229Activating the mobile phone navigation
system...............................................................229Compatibility of phones..................................229Installing the micro SD card..........................229
Glasses Holder................................................96Global Opening and Closing......................34
Global closing........................................................35Global opening......................................................35
HHandbrake
See: Parking Brake...............................................112Hazard Warning Flashers............................47Headlamp Levelling......................................46
Recommended headlamp levelling controlpositions..............................................................47
Headlamp Washers.......................................43Head Restraints..............................................89
Adjusting the head restraint............................89Removing the head restraint...........................89
Heated Seats...................................................92Heated Windows and Mirrors....................85
Heated exterior mirrors......................................85Heated windows..................................................85
HeatingSee: Climate Control..........................................80
Hints on Driving With Anti-LockBrakes..............................................................112
IImmobiliser
See: Engine immobiliser....................................36Important audio information....................173
Audio unit labels..................................................173Disc labels..............................................................173
Incorrect security code................................177
238
Index
Information Displays.....................................67General Information............................................67
Information Messages..................................74All wheel drive.......................................................75Doors open..............................................................75Keyless system......................................................76Lighting.....................................................................77Maintenance...........................................................77Message indicator................................................74Message symbols.................................................74Power steering.......................................................78Stability control (ESP).......................................78Transmission..........................................................78Tyre pressure monitoring system...................79Viewing current messages................................75
Instrument Cluster.........................................62Instrument Lighting Dimmer.....................93Interior Lamps.................................................49
Courtesy lamp.......................................................49Reading lamps......................................................49Vanity mirror lamps.............................................50
Introduction.........................................................7iPod connection
See: Connecting an external device.............221See: Connecting an external device - Vehicles
With: Bluetooth...............................................221iPod
See: Using an iPod.............................................224ISOFIX Anchor Points....................................21
Attaching a child restraint with a toptether.....................................................................21
JJump starting
See: Jump-Starting the Vehicle.....................153Jump-Starting the Vehicle........................153
To connect the booster cables......................153To start the engine.............................................154
KKeyless Entry....................................................32
Disabled keys.........................................................34General information............................................32Locking and unlocking the doors with the
key blade............................................................34Locking the vehicle..............................................33Passive key..............................................................33Unlocking the vehicle..........................................33
Keyless Starting..............................................99Failure to start.....................................................100Ignition on...............................................................99Starting a diesel engine.....................................99Starting with automatic transmission.........99Starting with manual transmission..............99Stopping the engine when the vehicle is
moving................................................................101Stopping the engine with the vehicle
stationary.........................................................100Keys and Remote Controls.........................28
LLighting Control..............................................45
Headlamp flasher................................................45Home safe lighting..............................................45Lighting control positions.................................45Main and dipped beam......................................45Parking lamps........................................................45
Lighting..............................................................45Load Carriers
See: Roof Racks and Load Carriers..............123Load Carrying..................................................121
General Information............................................121Loading compact discs..............................188
6000CD, Sony and Sony DAB......................188Loading the compact disc changer......188
239
Index
Locking and Unlocking.................................30Automatic relocking............................................32Central locking......................................................30Double locking......................................................30Double locking the doors with the key.........30Locking and unlocking confirmation............30Locking and unlocking the doors and the
luggage compartment lid with theremote control.................................................30
Locking and unlocking the doors frominside.....................................................................31
Locking and unlocking the doors with thekey.........................................................................30
Luggage compartment lid.................................31Reprogramming the unlocking
function...............................................................32Locks...................................................................30Lost security code.........................................177Luggage Anchor Points................................121Luggage Covers..............................................121
Stowing the luggage cover - vehicles withtyre repair kit....................................................122
MMaintenance....................................................141
General Information...........................................141Technical Specifications..................................149
Manual Climate Control...............................81Air conditioning.....................................................82Air distribution control........................................81Blower.......................................................................81Heating the interior quickly...............................81Recirculated air......................................................81Ventilation...............................................................82
Manual Seats..................................................90All vehicles.............................................................90
Manual Transmission.................................108Message Centre
See: Information Displays.................................67Mirrors
See: Heated Windows and Mirrors................85See: Windows and Mirrors................................59
MP3 connectionSee: Connecting an external device.............221See: Connecting an external device - Vehicles
With: Bluetooth...............................................221
MP3 display options....................................192CD text display options....................................192
MP3 file playback..........................................191Playing a multi session disc.............................191
NNavigation introduction............................228Navigation system commands................217Navigation system.......................................229News broadcasts..........................................187
All except Sony and Sony DAB......................187Sony and Sony DAB...........................................187
OOccupant protection.....................................23
Principle of Operation.........................................23Oil Check
See: Engine Oil Check.......................................146On/off control................................................179Opening and Closing the Bonnet............141
Closing the bonnet.............................................142Opening the bonnet...........................................141
PParking Aids.....................................................114
Principle of Operation........................................114Parking Brake...................................................112Parts and Accessories.....................................7
Look for the Ford logo on the followingparts .......................................................................8
Now you can be sure that your Ford partsare Ford parts.......................................................7
Personalised Settings...................................72Chime deactivation..............................................74Clock setting...........................................................72ESP.............................................................................72Help screen and navigation
information.........................................................72Language setting..................................................73Navigation information.......................................73Steering....................................................................72Units of measure...................................................73
Power Door LocksSee: Locking and Unlocking.............................30
240
Index
Power Seats......................................................916-way electric seat...............................................91
Power Steering Fluid Check.....................148Topping up............................................................148
Power Windows..............................................59Anti-trap function................................................59Driver's door switches........................................59Global opening and closing.............................59Opening and closing the windows
automatically....................................................59Resetting the memory of the electric
windows.............................................................60Safety switch for rear windows......................59
Programming the remote control............28
RRear Fog Lamps.............................................46Rear Seats..........................................................91
Creating a level load floor.................................92Folding the seatbacks down............................92Folding the seatbacks up..................................92
Rear Under Floor Storage..........................122Rear view camera..........................................116
Principle of Operation........................................116Rear Window Wiper and Washers...........42
Intermittent wipe..................................................42Rear window washer..........................................43Reverse gear wipe................................................42
Refuelling........................................................105Regional mode (REG)................................186
All except Sony and Sony DAB.....................186Sony and Sony DAB...........................................187
Remote control batterySee: Changing the remote control
battery.................................................................28Remote control programming
See: Programming the remote control........28Removing a Headlamp................................50Repairing Minor Paint Damage................152Repeat compact disc tracks....................190
6000CD................................................................190Sony and Sony DAB..........................................190
Road Safety...................................................228Safety information............................................228
Roadside Emergencies................................131
Roof Racks and Load Carriers..................123Cycle carrier...........................................................124Installing the crossbars....................................123Roof rack................................................................123
Run Flat Tyres................................................163Principle of operation........................................163Replacing run flat tyres....................................164What to do if a run flat tyre has a
puncture............................................................164Running-In......................................................130
Brakes and clutch...............................................130Engine.....................................................................130Tyres........................................................................130
SSafety Precautions......................................103Satellite Navigation Unit Holder..............98
Adjusting the holder...........................................98Seat belt height adjustment......................25Seat belt reminder.........................................25
Deactivating the seat belt reminder.............26Seat belts
See: Fastening the seat belts...........................25Seats...................................................................89Security code..................................................177Setting the clock and date on the audio
unit...................................................................1786000CD.................................................................178Sony and Sony DAB...........................................178
Shuffle/random............................................1896000CD.................................................................189Sony CD and Sony CD DAB............................190
Sitting in the Correct Position...................89Snow Chains
See: Using Snow Chains..................................165Speed Control
See: Cruise Control.............................................119Stability Control.............................................113
Principle of Operation........................................113Starting and Stopping the Engine...........99
General Information...........................................99Station preset buttons................................181Station tuning control.................................183
DAB service linking.............................................183Manual tuning......................................................184Scan tuning...........................................................184Seek tuning...........................................................183
241
Index
Status after a collision................................132Steering Wheel...............................................39Storage compartments...............................95
Front storage compartment............................95Storage area under the rear seats.................95
Sun Shades......................................................93Panoramic roof.....................................................93
Switching Off the Engine...........................101Vehicles with a turbocharger..........................101
Symbols Glossary.............................................7Symbols in this handbook...................................7Symbols on your vehicle.......................................7
TTechnical Specifications
See: Capacities and Specifications.............170Telephone commands................................212
Create a phonebook..........................................215Main settings........................................................216Phone......................................................................212Phone functions..................................................213
Telephone controls......................................197Remote control....................................................197
Telephone setup...........................................195Bond another Bluetooth phone....................196Making a phone an active phone.................195Phonebook...........................................................195Phonebook categories.....................................195
Telephone.......................................................195General Information..........................................195
TelephoneSee: Using the telephone - Vehicles With:
Navigation System......................................200See: Using the telephone - Vehicles Without:
Navigation System........................................197Toll Reader.......................................................96Tow Ball............................................................126
Driving with a trailer...........................................128Inserting the tow ball arm................................127Maintenance.........................................................128Removing the tow ball arm............................128Unlocking the tow ball arm
mechanism.......................................................127Towing a Trailer.............................................126
Steep gradients...................................................126Towing Points................................................139
Towing the Vehicle on FourWheels...........................................................139All vehicles............................................................139Vehicles with automatic
transmission....................................................140Towing..............................................................126Track selection..............................................188
All except Sony and Sony DAB.....................188Sony and Sony DAB..........................................188
Traffic information control........................182Activating traffic announcements...............182Ending traffic announcements.....................183Local or distant traffic......................................182To adjust the preset volume...........................183Traffic announcement volume......................183
Transmission.................................................108Trip Computer.................................................70
Type 2 and 3...........................................................70Type approvals..............................................231
FCC/INDUSTRY CANADA NOTICE..............231RX-42 - declaration of conformity...............231
Tyre Care..........................................................165Tyre Pressure Monitoring System..........165
System reset........................................................166Tyre Pressures
See: Technical Specifications........................166Tyre Repair Kit...............................................160
Checking the tyre pressure.............................162General information..........................................160Inflating the tyre...................................................161Using the tyre repair kit....................................160
TyresSee: Wheels and Tyres.....................................155
UUnder Bonnet Overview - 2.0L
Duratorq-TDCi (DW) Diesel..................144Under Bonnet Overview - 2.5L Duratec
(VI5)...............................................................143Unloading the compact disc
changer.........................................................189USB port............................................................97USB
See: Using a USB device..................................222
242
Index
Using an iPod.................................................224CD Navigation units..........................................226SD Navigation units..........................................226Sony radio.............................................................225
Using a USB device.....................................222CD Navigation units...........................................223SD Navigation units...........................................224Sony radio.............................................................222
Using Cruise Control.....................................119Cancelling the set speed.................................120Changing the set speed....................................119Resuming the set speed..................................120Setting a speed....................................................119Switching cruise control off............................120Switching cruise control on.............................119
Using seat belts during pregnancy..........26Using Snow Chains......................................165
Vehicles with stability control (ESP)..........165Using Stability Control.................................113Using the Parking Aid...................................114
Manoeuvring with the parking aid.................114Switching the parking aid on and off...........114
Using the Rear View Camera....................116Activating the rear view camera....................116Deactivating the rear view camera...............118Using the display.................................................116Vehicles with parking aid..................................118
Using the telephone - Vehicles With:Navigation System..................................200Changing the active phone.............................201Debonding a bonded phone..........................201Making a call.......................................................200Muting the microphone..................................200Receiving an incoming call............................200Receiving a second incoming call...............200
Using the telephone - Vehicles Without:Navigation System....................................197Changing the active phone............................199Debonding a bonded phone..........................199Debonding a bonded phone - Sony
radio....................................................................199Making a call.........................................................197Muting the microphone...................................199Receiving an incoming call.............................198Receiving a second incoming call................198
Using voice control.....................................202Name tag..............................................................203System operation..............................................202
Using Winter Tyres.......................................165
VVehicle battery...............................................153Vehicle Care.....................................................151Vehicle Identification Number................169Vehicle Identification Plate......................169Vehicle identification..................................169Vehicle recovery............................................139Ventilation
See: Climate Control..........................................80Vents
See: Air Vents........................................................80VIN
See: Vehicle Identification Number.............169Voice control.................................................202
Principle of Operation......................................202Voice Control...................................................40
WWarning Lamps and Indicators.................63
ABS warning lamp...............................................63Airbag warning lamp...........................................63Brake system lamp..............................................63Cruise control indicator......................................63Direction indicators.............................................63Doors open warning lamp................................63Engine warning lamp..........................................64Front fog lamp indicator....................................64Frost warning lamp.............................................64Glow plug indicator.............................................64Headlamp indicator............................................64Ignition warning lamp........................................64Low fuel level warning lamp............................64Main beam indicator...........................................64Message indicator................................................64Oil pressure warning lamp...............................64Power steering warning lamp.........................65Rear fog lamp indicator.....................................65Seat belt reminder...............................................65Shift indicator........................................................65Stability control (ESP) indicator....................65
Warning Triangle............................................131Washer Fluid Check.....................................148Washers
See: Wipers and Washers..................................41
243
Index
WashingSee: Cleaning the Exterior................................151
Waveband button.........................................181All except Sony and Sony DAB.......................181Sony and Sony DAB............................................181
Wheels and Tyres.........................................155General Information..........................................155Technical Specifications.................................166
Windows and Mirrors....................................59Windscreen Washers....................................42Windscreen Wipers........................................41
Automatic wiper system....................................41Intermittent wipe..................................................41
Winter TyresSee: Using Winter Tyres...................................165
Wipers and Washers......................................41
244
Index
(CG3542en)