FORM NUMBER: 88-174-03 DATE: 08/30/80 REVISED: 07/13/81, 06/04/84, 03122188

WARRENIISHERER

MODEL:

MlA(G) - M4A(G) MEAT MERCHANDISER MlAHG - CHEESE MERCHANDISER

PIZZA CASE

THIS REFRIGERATOR CONFORMS TO THE COMMERCIAL REFRIGERATOR MANUFACTURERS ASSOCIATION HEALTH AND SANITATION STANDARD CRS-SI-86

WARREN//SHEFUiit DIVISION OF KYSOR INDUSTRIAL CORPORATION

1600 ROCKDALE INDUSTRIAL BLVD., CONYERS, GEORGIA 30207 / 770~483~5600

INSTALLATION AND OPERATING INSTRUCTIONS

FOR

MWG) I M4A(G) and LMl(G) MODELS

SELF-SERVICE MEAT CASES

APPLICATION:

The Warren/Sherer single and multi-shelf and self-service meat cases are designed to merchandise packaged fresh (red) meats and deli products. The LMl(G) cases are designed for packaged frozen meat products. These cases should be installed and operated according to the instructions contained in the manual to insure proper performance. They are designed for display of products in an air-conditioned store where temperature and humidity are maintained at a maximum of 750degree-F dry bulb temperature, 55% relative humidity, and *minimum of 650degree-F, 35% 'relative humidity.

*Defrost times may be excessive if temperature and humidity drop below the minimum noted.

MODEL DESCRIPTION

MlA Single Deck Meat, Air Defrost, Metal Front

MlAG Single Deck Meat, Air Defrost, Glass Front

M4A Multi-Deck Meat or Deli, Air Defrost, Metal Front, Usually two or three Adjustable Shelves

M4AG Multi-Deck Meat or Deli, Air Defrost, Glass Front, Usually two or three Adjustable Shelves

LPI1 Single Deck Frozen Meat, Electric Defrost, Metal Front

LMlG Single Deck Frozen Meat, Electric Defrost, Glass Front

MlAHG Single Deck, High Glass, Air Defrost Cheese Merchandiser

MlA(G) Single Deck, Air Defrost Pizza Merchandiser (Rear Work Surface and Condiment Trays)

ALL CLAIMS FOR SHORTAGES MUST BE MADE WITHIN TEN DAYS OF RECEIPT OF SHIPMENT. ANY SHORTAGES CLAIMED AFTER TEN DAYS WILL BE INVOICED AS ADDITIONAL PARTS.

Rev. 07/13/81 06/04/84 03/22/88

GENERAL These display refrigerators may be installed individually or in a continuous line-up consisting of several 8-foot and 120foot sections by using a joint trim kit. A plexiglass divider kit must be used between cases operating on different refrigeration systems. Divider will be factory installed if specified on order. \

SHIPPING DAMAGE -m*prnent should be examined for shipping damage before and during unloading. If there is any damage, the carrier should be notified immediately and an inspection requested. The delivery receipt "must" be noted that the equipment was received damaged. If damage is of a concealed nature you must contact the carrier immediately or no later than three (3) days following delivery. A claim must be filed with the carrier by the consignee for all damages.

NOTICE: ALL mIl’!S FOR SIKxI’AGES MUST BE MADE WITHIN 10 DAYS AFTER RECEIPT 1 OF SHIPMENT.

LOCATION This refrigerator must be located on a firmly based floor and leveled within plus or minus l/16". Use shims provided to level your refrigerator.

JOINING Two or more fixtures of like models can be joined together to form a continuous line-up. Instructions for joining fixtures are included in the joint kit. Before lining up refrigerator, inspect refrigeration lines, electrical connections and controls to.insure refrigerators are in proper line-up and are in the proper sequence.

Note: THESE REFRIGERATORS ARE LINED UP AT THE FACTORY ANDARE NUMBERED. INSURE THEY ARE LINED UP IN THE FIELD IN THE SAME SEQUENCE NUMBER.

WASTE OUTLET These cases are equipped with a l-l/2" FPI waste outlet connection which terminates in

f he center of th

sea, trap IS R refrigera or below the insulated bottom. A 1~1/2" galv. water

furnx ed for fie d installation. 4

INSTALLING DRIP PIPE Improperlyinstalleddrip pipes can seriously effect the operation of this e ui m nt nd resu t in increased maintenance costs. gSene!S P a l ru es for. rip pipe installation..

Listed below are some I

1. Use the external water seal provided with the equipment. Never double seal a line.

2. Never use a pipe smaller than the size pipe or water seal supplied with the equipment.

3. Always provide as much as fall ai possible in drip pipe. (1" fall for each 4' of drip pipe.)

4. Avoid long runs in drip pipe which make it impossible to provide maximum fall mpe.

5. Provide a drip space bet>/een drip pipe and floor drain or sewer connection,

6. Do not allow drip pipe to come in contact with uninsulated suction lines, xichwill cause the condensation from your refrigerator to freeze.

Rev. 6/4/U

- - 2 MlA(G)/M4A(G)

CLEANING To insure minikm maintenance cost, cabinet should be thoroughly emptied and' washed out every three (3) months. The exterior should be washed weekly. A mild soap and water solution is recommended for painted surfaces of the cabinet. DO not use cleaners contafninq abrasive materials which will scratch or dull finish. The waste outlet shoild be flushed with a bucket of water following each cleaning.

Cautipn: N&er introduce water into the fixture faster than the waste outlet can carry it away.

When cleaning lighted shelves, wipe down with a wet sponge or cloth so that waler does not enter the light rails. DO NOT USE A HOSE OR SUBMERGE SHELVES IN WATER. BE SURE REFRIGERATION IS SHUT-OFF AND ALL ELECTRICAL IS OFF BEFORE -YOUR REFRIGERATOR. . I

LOADING Merchandise should not be. placed in the fixture until all controls have been adjusted and the refrigerator is at proper temperature.

At no time should the fixture be stocked beyond the load line located on the top of the back baffle and each end of the refrigerator or over the front edge of adjustable shelves.

For proper operation, you must not stock merchandise above the load lines. In doing so, you will seriously affect the performance, which will result in higher product temperatures and increase operating costs. m

ELECTRICAL All field installed' wiring must comply with the NATIONAL ELECTRICAL CODE AND LOCAL CODES.

-

4

- I

I I

ELECTRICAL RACEWAY An electrical raceway is provided with each refrigerator for running your fan, anti-sweat heaters, and defrost circuits from case to case without using conduit. This applies, of.course, when the front panel is properly secured into position. This is an approved method by the Underwriters' Laboratories; however, wiring must be run in accordance with local and national electrical codes.

ELECTRICAL COf'!NECTIONS All field connections are made in the electrical raceway. .

Make sure that proper voltage is supplied to your refrigerator. Check refrigerator nameplate for fan and anti-sweat volts and defrost volts. If a canopy is furnished, l "\ ':' use a separate fused circuit. ALL REFRIGERATORS MUST BE GROUNDED.

Fan motors must operate continuously and panel must be marked sufficiently to prevent. the fan motors and anti-sweat heaters from being turned off accidentally. ljhen

:

refrigerators are mu1 tiplexed, add the total of these amperage valves to determine e wire size and circuit protection. control the anti-condensate heater.

Anti-condensate controllers can be used to

3 - -

employed for safe operation.

Chart #l shows the electrical ratings information that appears on your refr

REFRIGERATING FAN MOTORS ‘The fan motors employed are permanent ly oiled for the 1 ife of the motor and requires no periodic maintenance. They are wired according to the enclosed wiring diagram and MUST RUN CONTINUOUSLY.

On electric defrost models, the defrost heater amperages should be added together, and if their rating exceeds the defrost time clock or condensing unit break& capacity, a defrost relay and circuit breaker must be employed and furnished by others. Make sure that proper wire size and branch circuit protection are

for your refrigerator. This is the same igeration nameplate.

ANTILSWEAT HEATERS fhese heaters are placed in the fixture to eliminate sweat forming on certain areas of fixture.

EXPANSION VALVE The expansealve furnished with your refrigerator has been sized for maximum coil efficiency. To adjust superheat, place a thermocouple under the expansion valve bulb. Read the suction line pressure as near coil as possible. (If at the condensing unit, estimate suction line loss at ZPSIG). Convert coil suction pressure to temperature. The difference between coil temperature and the thermocouple, temperature is superheat. (Use average superheat when expansion valve is hunting). Do not set superheat until cases have pulled down to operating temperature and never open or close valve over l/2 turn between adjustments and allow 10 minutes or more between adjustments. Superheat should be set to 6-8OF.

REFRIGERATION LINES 'The refrigeratmnes are located under the deck pans on the 8' and 12' cases. A refrigeration outlet is provided in the front RH end of the case. Make sure . all refrigeration lines lie as close to the refrigerator bottom so as not to obstruct the air pattern or block the deck pans. See the section on "Recommended Piping Practice? for additional details on piping practices.

These 8' and 12' refrigerators have polyurethane foamed-in-place insulation. In opening a ferrule hole, simply heat a piece of copper tubing of the same size as the tubing to be employed an,d force it through the ferrule hole.

IMPORTANT - SEAL AROUND LINES AFTER CONNECTIONS ARE MADE. KEEP DIRECT FLAME FROM BOTTOM OF REFRIGERATOR, AS HEAT WILL DISINTEGRATE THE ALUMINUM BOTTOM AND INSULATION. USE A HEAT SHIELD WHEN WELDING NEAR THE BOTTOM OF THE CASES.

REFRIGERANT R 12 expansion valves are standard. If other refrigerant is used, the order mist specify the expansion valve to be supplied.

HEAT EXCHAIVGER Heat exchangers are standard in these refrigerators. They aid to increase operating efficiency and reduce frosting and flood-back to compressor.

i t

i

4 - - MlA(G)/M4A(G)

OPERATION .

On single condensing unit systems a thermostat should be used to control temperatures. The thermostat bulb should be mounted in the discharge air. On parallel units, temperature control can be provided by EPR valve, thermostat and liquid line *solenoid or solid state low pressure controls on compressor unit. Chart #2 shows approximate settings for merchandisers. Since many variables are present in each installation, such as store temperature, length of tubing runs, temperature desired in refrigerator, etc., Chart #2 is only a guide for the installer. *See Chart #2 note 2.

DEHYDRATION OF REFRIGERATION SYSTEMS ‘ Please read carefully before placing system into operation. After 13ying

a 6 refrigerant lines, they should be blown out before making final connection at fixture or condensing unit. Use dry nitrogen to prevent any foreign matter being left in the lines. Keep pressure below 250 pounds. To prevent scaling due to brazing, dry nitrogen should be allowed to flow through lines while brazing operations are taking place.

After the refrigeration system has been pressure-tested and proven leak-free, it is recommended that the system be dehydrated with a vacuum pump to 1000 microns for the first two evacuations and 500 microns on the third. The triple evacuazion method requires evacuating the system three successive times and breaking each vacuum with dry refrigerant. Allow the pressure to rise above atmospheric pressure.

DEFROST CYCLE . m .

"AIR DEFROST" Models - On these model refrigerators, the evaporator fans run continuousiy; however, they reverse the air flow during defrost cycle. In defrost, the air is pulled into the case through the refrigeration discharge grille, through the ducts, coils, and discharged out the return air duct.

Defrost termination is by bi-metal "fixed" temperature control, wired in series and set to terminate at 45OF on the coil. See Chart #2 for defrost clock control settings. The defrost cycle is started by the time clock, which reverses the contacts on the relay normally installed at the case, causing the evaporator fan motors to reverse and reverse the air flow to defrost the coils.

"HOT GAS DEFROST" Models - On hot gas defrost models, (optional for parallel compressors operation only) hot gas is routed through the suction line and evaporator coil. It exits the coil through a by-pass around the expansion valve and heat exchanger to return to the liquid line where the "condensed" liquid is used to feed the other cases on the same parallel unit. The case fans continue to operate during defrost to warm up the drain pan and air ducts.

On hot gas models, located at the

an adjustable termination control is used. The control is left end of the case behind the lower front panel. The control

bulb is at the same end of the case in the discharge air stream above the coil.

NOTE: DO NOT USE PUFF DOV?? SYSTEXS Tr;ITH AIR DEFROST. ON PARALLEL COWRESSOR SYSTEMS, AN ELECTRIC STOP EPR VALVE OR SOLEXOID IS REQUIRED IN THE SUCTION LIXE.

Rev. 6/b/8$

- - 5 MlA(G)/M4A(G)

Chart #l

Model

Evaporator Fans

(Amd --

MlA 8

MlAG II

MlA 12

MlAG 12

M4A 8

M4AG 8

M4A 12

M4AG 72

. 6

.6 ’

. 9

. 9

. 6

. 6 0 8 1.6

. 9

. 9

Anti-Cond Heater (Amps)

. 7

11 .

1.3

17 0

. 4

. 6

1.1

Lights (Amps)

1.6

21 .

2 1 .

For each lighted shelf, add .7 amps per shelf

*. . . .

Rev. 6/4/84

6 - -

Chart #2 .

Model M7Ao

MlA(G)

M4A(G)

M4A(G)

M4A(G)

M4A(G)

Models 'M1A(G)

M4AG

Re commended Control Settings

Refrigerant LP Control EPR Valve t;g y; (

12#

502 - Meat 39 PSIG 63PSIG 38# 20 24 .

R-12 - Meat 11 PSIG 27PSIG 12# 22 26

R-502 - Meat 37 PSIG 63PSIG 38fif 22 26

R-12 - Deli 73 PSIG 27PSIG 14# 25 29

R-502 Deli 42 PSIG 63PSIG 42# 25 29

Defrost Periods Termination Fail Safe Setting Frequency Air Hot Gas Air Hot Gas

3 45°F 50°F 45 min. 18 min.

6 45'F 50°F 45 min. 78 min.

Thermostat (D isc. Air Temp) Cut-out Cut-in

20 24

Note: (1) A defrost termination control is installed on the coil of each MlA and two on the M4A. These must be wired in series with trip solenoid on the time clock.

(2) Do not use pump down systems with air defrost. On parallel compressor systems, an electric EPR valve on solenoid is required in the suction line.

(3) Hot gas models use an adjustable defrost termination control.

.

REV. 614184

- - 7

MlA(G) & M4A(G) Parts List .

MlA(G) 8' M4A(G) 8' 12' MlA(G)

3 3

M4A(G) 12' Part No.

9AlO-39 9810-13 9BlO-21 3AlO-22 3All-23 3Al2-21 8All-26 8All-27 8Ell-38 8EW37 8Ell-54

lOKl4-59 lOK14-58 73A75-12 54Pl6-207 54P16-208 13A15-10 81 Al 2-34 81 Al 4-34

Description

Evap Fan Motor Evap Farr Blade

2 2

2 3

3 2 Expansion Valve 1

1 1

Defrost Control Temp Cntrl (optional) Defrost Relay Defrost Relay Base Alternate Def Relay

,Capacitor

Honeycomb (plastic) 2 Discharge Grille 1

1 Ref. Jet Honeycomb AntiSweat Htr(thermop)

2 1

3

1 1

1 Back Rail Heater 1

1 Honeycomb Heater 1 8lClO-77

81 Cll-77 14010-29 14DlO-30 15317-43 15511-44 54628-74 10811-19 lOBll-20 lOAlO-48 lOAlO-47, lODlO-27 lODlO-36 lOBll-17 10611-18 lOAlO-17 10572-11 . lODlO-12 ** 60Nll-48 56313912 56J13-17 28619-130 5lAl2-714 51n14-95 5lN2-115 5lAl4-96 57Cl2-59 51C14-55

Thermopane (Glass) 1 1

Thermopane Cap 1 1 3 Front Baffle (61 ass)

Lamp Holders (Canopy)

Lamps (canopy)

Ballast (canopy) 1

Lamp Holder (l/adj shlf)

Lamp Starter Ballast External Drain Trap Deck Pans

1 1 4

4 4 1

Adj Wire Rack Lower Front Panel

4 7

Upper Front Panel 1 1

Canopy Front Panel 1

i core) Revised 7/13/81

Parts List Cont.

Description MlA(G) 8' M4A(G) 8' MlA(G) 12' M4A(G) 12' Part No.

Kickplate (painted) 7 1 51Al2-118 5lAl4-99 1

Kickplate (opt ss) Brushed Bright Brushed Bright Brushed Bright

Col&band Brushed

1 1

55A32-194 55A32-795 55A32-798 551132-199 55A32-196 55A32-197

1 1

1 1 1

Canopy Colorband Insert (painted) 1 1 51A34-19

5lA34-20 1 Colorband Insert

(painted) 1 1 51A34-10 5lA34-11 1 1

Colorband Insert (vinyl Heritage) 1 1 53ElO-41

53ElO-42 1 1 Colorband Insert (gold anodized) 1 1 62520-31

62J20-33 1 w 1

*G Models

Rev. 7/13/81

9 - -

RECOMMENDED PIPING PRACTICES FOR NARREN/SHERER CASES f/25/80

1. Proper size refrigeration lines are essential to good refrigeration performance. Suction lines are more critical than liquid or discharge lines. Oversized suction lines may prevent good oil return to the compressor. Undersized lines can rob refrigeration capacity and increase operating cost. Consult the technical manual or legend sheet for proper line sizes.

2. Refrigeration lines in cases in line-ups can be reduced. However, the lines should be no smaller than the main trunk lines in at least l/3 of the cases and no smaller than one size above the case lines to the last case. Reductions should not exceed one line size per case. It is preferred to bring the main trunk lines in at the center of line-up. Liquid lines on systems on hot gas defrost must be increased one line size above the main trunk line for the entire line-up. Individual feed lines should be at the bottom of the liquid header.

3. Do not run refrigeration lines from one system through cases on another system.

4. Use dry nitrogen in lines during the brazing to prevent scaling and oxidation.

5. Insulate suction lines from the cases to the compressor with 3/4" wall thickness Armaflex or equal on low temp cases to provide maximum of 65O sub- cooled gas back to the compressor and prevent condensation in exposed areas. Insulate suction lines on medium temp cases with l/2" thick insulation in exposed areas to prevent condensate drippage.

6. Suction and liquid lines should never be taped or soldered together. Adequate heat exchanger is provided in the case.

.

7. Refrigeration lines should never be placed in the ground unless they are protected against moisture and electrolysis .attack.

8 . Always sfope suction lines down toward the compressor, l/2" each 10'. Do not leave dips in the line that would trap oil.

9. Provide "P*' traps at the bottom of suction line risors, 4' or longer. Use a double "P" trap for each 20' of risors. "PII traps should be the same size as the horizontal line. Consult the technical manual or legend sheet for proper size risors. *

10. Use long radius ells and avoid 45" ells.

11. Provide expansion loops in suction lines on systems on hot gas defrost. An expansion loop is required for each 100' of straight run.

12. Strap and support tubing to prevent excessive line vibration and noise.

13. Brazing of copper to copper should be with a minimum of 10% silver. Copper to brass or copper to steel should be with 45% silver.

14. Avoid the use of "bull head" tees in suction lines. An example is where suction gas enters both ends of the tee and exits the center. This can cause a substantial increase in pressure drop in the suction lines.

15. lcihen connecting more than one suction line to a main trunk line, connect each branch line with an inverted trap.

-100

.

I .

f 0 - I- c) W

0 I J

W n

0 1

I .-

!

I n

rl

l 2

(5.1 CM

)

i

-AN

RELAY

30X :SER

VICE

ON

LY) t

12’0 0”

(3 6 5.8

CM

)

0 8’-

0” (243.8

CM

) (5 .

CASE

WASTE

OU

TLET

I II

- 7/ 2

(l9CM

) I 7.

ym-

- -

317 -

I9/4

-&g- -

,(59.7 C

M)

L (48.9C

M)

I

2 II

I CM

)

(11307CM

)

c I

I J

1

REFR

IGER

ATION

C

ON

NEC

TION

AR

EA FO

R”STU

B-UPS”

DR

AIN

CO

NN

ECTIO

N

(W/TR

AP)RlG

HT

OR

LE

FT ELEC

TRIC

AL C

ON

NEC

TION

b LETTER REVISED

I DATE

BY I

~Z!SEP~I ] ‘lTLE

P

LAN

VIEW

- - - - - - -_ - - - -m-e

i

I A

i 6

I I

;

1 ,

M4A 3

/ /

. 73i4 I (186.7CM)

(83.8CM)

M4AG

(78:7&l)

M4A L I

1 I . I I 1 I

I

I I

4--l4~*~-~---- 32" (36.2CM)

NOTE: UPPER SkiELvES OPTIONAL ACCESSORY (DOWNSLOPE OR HORIZONTAL-LiGHTED OR UNUWiTED)

.

3 W

t- W

c) 1

W z z

OT 0

Z 0 I- < 01 W c3

cc L W

4 u I-

t

I- W -I I- 3 0

3 >

Z < -I a-

W

c f

Z 0

W l- m d 3

W Z Z 0 u

W w Q u

- - - - - - . - - - - - - - - Y _- - - - - - - - - . - - _- - -

i ! , -- .- -.---- -.- -- . - _ 1 --em-. - .-mm- __.

OPTI

ONAL

Tf

M

PERA

TURE

9

NRPL

E

PuRP

LE

THER

tiOST

AT

IO

--

OPT

IOEJ

.AL

TEM

P,

THER

MO

STAT

(C

LOSE

ON

RI

SE)

WIR

EWAY

-

DEfR

OSl-

TERM

INNI

OEJ

17

BROW

N

TtW

W/rS

TN-

I8 BR

OWN

I LE

CfNO

:, -

.m _

- -a

12

CA

SE

L

q J

OfF

ROST

TC

RMIN

ATIO

N Tt

iERM

OSl

-AT

(ClBS

E CN

RI

SE)

IISV.

A/

S HE

ATER

I

BLAC

K

CIRC

UIT

2 wt

ll T-

E:

w - -

--- .-

-- ( R

If9-W

0

-i (R

l88ED

) e t - .

t BL

UE

I I

TOP

CAP

A/S

HEAT

ER

I

ll5V,

FA

N Cl

RCUl

l- 8L

ACK

3- 4 wi

ll-f

c L1 - -- --

I d m

BL

ACK

THfR

t/lOf’A

t It:

A

13

r!tAT

f R

(MIA

(C)

GtJL

Y)

CAZC

RA

CEW

AY

fVAP

ORAT

OR

fAN

MQ

TGP

S

BLAC

K

OAT

&0

4/00

TnL‘

--I

WIR

ING

D

IAG

RAM

’

DeA

LI

NONE

M

IA(G

) 8

& 12

EL

EC’L

Of’?

HOT

GAS

0-r

CAPA

CIT-

OR

t . , RELAY

NOT-E :

OEfRcm-

SHOWN

IN

OPr!O

EJAL TEM

P. -

REF- RIGERATION IvXJO

E.

THERMO

STAT ( CLOSE

ON RISE)

* O

PTIONAL

’ TEM

PERATURE 9

PURPLE

THERMoSTAI-

lo PURPLE

WIREW

AY F

OEFROST- lTFIb.1INATIO

N 17

BROWN

THERMO

ST-AT I8

. 0ROW

N

LEGENO _ _ __

_ _ _ I2

’ CASE

“’ M

UST i3E

GROUNDED

ll5V A IS

HEATER I

FLACK

CIRCUIT 2

WHITE

(RUBBED)

/ I

OEffwsr

TERMINAT

_ THERM

OSTAJ-

(CLOSE ON

RISE: 11%

FAN

CIRCUIT (RIEHD)

BLUE

I ’

TOP

CAP A /S

HEATER SLACK

L 1

I I

I I

b 1

I I Z33V.

?lscm-

CLCCK (PJ 10

CClJ=-CTS)

(,PllONAL II5

Vn) (SE

TAG FOR

PROPER VOtJAGE)

d-l BLAC

K I

;--. 9

wt 41 l-E

! p!yc9) I

- --

----- - 4

PI-I ‘E

t ---

_I_- .-.-..

PI

.*.----4 -

l .

- -

_- .

. I

* -_-

. se.

-. -

. _-.__

- _

___

-. ,, .

9 -Y

- =..f‘

.?’ ’

* T’

7

J

I

r

-_ +

e-m A-.--J

I I

1 I

-- &

--- _

..J

_ _

_. J

Ir

CGE RACEW

AY HANOY

BOX __II__+

%/rCK

i I

J 9LACK

1 --

- -----

*. BLUE

a 3

-18-

tn a

I

r +

. . ,-: . . . . l .

. . 8.

c/, r--T--T-i

-a

.

-19-

WHI

TE

(RIB

SE3)

r

1 Is’4

LlG

HTt

NG

CIRC

UIT

5 6 E3

LACK

I

PURP

LE

OPTI

ONAL

TE

MPE

RTUR

E 9

THER

MO

STAT

IO

-=

=-I

OPTI

ONAL

I-E

tiP.

THEf

UdOS

-l-A-l-

(CLO

SE

ON

RISE

) W

IREW

AY

------

+ I

I I

I

12’

CASE

LI

GHTS

8’ CA

SE

LIG

HT

DEFR

OST

TERM

INAT

ION

17

BROW

N s

THER

MO

STAT

18

BR

OWN

0 .

l a b

. .

BLAC

K AC

CESS

O3Y

LIG

HTED

SH

Eif

II%/.

A/S

HEAT

ER

CIRC

UIT

I wt

wE

(R19

XD)

’ DE

FROS

T TE

FUvk

RE

CEPT

ACLE

S 2

THER

MO

STAT

I

(CLO

SE

ON

RISE

)

WHI

TE

ppf

BLUE

)

I EJ

ALLA

3T

1 BL

UE

’ 11

%

FAN

CIRC

UIT

3 BL

ACK

,

,lt

MUS

T RF

: C,

ROUN

DED

23OV

. DE

FROS

T CL

OCK

7 -I-

---

Y

ELLO

”” --_

I__

( N/

O CO

NTAC

TS

) 8

RED

1 (~

TI~+

JAL

113

v)(

su

TAG

foR

*

PRGP

fR

~OLT

AI;E

) 1

l

‘I b ACCE

SSOR

Y LIG

HTED

St

if Lf

OPTI

ONAL

-t -

BL

ACK

BLAC

K

BLUE

. NO

TE

: DE

FROS

T RE

LAY

-- --

-- 3-

-lOi’/t

~I

IN

PE F

-PIG

- ’

ERA?

-IOU

MOD

E.

LESE

ND:

,,,,J2

’CAS

E

TnL8

WIR

ING

DI

AGRA

M

’ M

~A(G

) 8’

4 l&

AIR

DEfR

OSl-

CAPA

CITO

R

T I VI 4

w m

CD

n

?

z 0 m 0

r- ’ 5

I 4 z G, mz

43: B-

‘E 4

n

s A

C

: ;5 z

. L

.

i

1

. .

8 .B : ‘.

i

i i

-22- .

\ -

4 4

-- /V

I I_

- 1

A n+.

-- -_

_ Lc

-_- s

t ---

-- 2’ t

--.

-._

- c

---_-

- d -7

9 -e-m

-- N iv

---

- 7

---

1 ;Y

.--

a

r f H-

9 9 -_

. 4 3

-

0 3 _

0 -.

v W

3lI

A--

.

F i.7

- !

/ -

,j G

i __

_- -_

- .

.__ --_

- -

- -_

-- OL

-

CVP5

G e-

-----e

-

- _--

-_ -.

- 69

-

C’/P

~.

.-__

_---_

-.

--.__

. __-

__

i. 9

- c’/

,‘~?2

---

---

-.-.--

_-

.- -.

61

- ;/,

?/j

-.--.e

---

.-----

-. .

----*-

----

;--

_-_-

-_---

-----.

_I__

- 0s

m

s-

z/,

.x ?

v - 5

Y #

f4Fa

3S

. .-- .I

- ---

---

__-

_ _ .--_

_-. a -.-

- - --

- ---

- -

.- ----

.- -

.----

-.---

,c;w

g Pp

.%'

Zf-$

72

- .'b

!3&7

7 - _

--__-

. _-

---_

- _.

___

_ --.

-- ---

---

-. -

. _---

.--

-.-

_ _

- --I

-::

‘g

;';v/I"

,yyJj'

c7

py

);‘Z/

j z

! t-F

/- q-

._

_ __

__ -

_ _-

_ _-

.._ __

--m

------

- -

--_

r*,

(-yv

?S f

/73

t+

- ?3

vs t

m

_-- ---

----e

--.---

-P-

----_

I- AC

-- -.-

---

--_-_

. -

77t+5

“71

C/

I’y?f

9--

-Ad_

. .d

. _ _

- __

--

-.--

-. . .

-_

_-.

- __

__-

- c

-_ -e?

--.

I--

-. a-

-- .

. ---

------

m--P

---

.&&f

’ 73

NQd

>/ZY

G -

h%Yf

---

-- w

s-P dl

SY0

Lr//Z

ifl a

73/3

7b’/‘t

;l’H3

---_I

___-

_ --

--

.---

lN/D

f dW

d2

f -

b&lL

Jl

-----

--_--

------

-- IN

/Of’

Uffb

SB3W

J-

Wlt3

’L

.-_-_

-__

-- _-

____

-- ---

_----

e-e

_I-_

_.

-- . .

.^ _-

1

r/xP

3 “zw

t%

7 .a

YE

2 -

w2u

, -..-

- --

._-

a-_

____

____

_-_-

-----

------

--.

---e-

P---

-___

___-

----m

--

I

1 iw

.7in

31

t-j

72’

7 3.

2 -

Il’mL

1fwo

r 73

NW

1Ny”

2J

23dd

i7

- I4

’/bl

---_.e

- -_

-P-P

- .--

------

e

z/ -

/I t&

Z ---

-m

-e---

---

- - -

/f

- a

3L33

--.

-__-

-*e

--d-d

- //

- E-

1 f-?

6/

---e_

_-

__-.

-..--

ia -

5/b%

/ ---

--.

_-

-..-

- _--

- .--

Gl

- //j/

G

I- --

P-P

NOIld

IU3S

30

,- __

----

---__

_I_

m-e

-- ‘O

N

MW

d ll_

_l---

.T---

---

I 03

tww

a j--

----- LB

P -~

lVt%

~Y

~'U

/A/U

'X

376\

"" 9b

f/ w

-a77

w

si

3aow

-_

-- -----

1

I NOTES

1. MOYE REfR1GE:RATORS AS NEAR THEIR PERMANENT COtATION AS POSSIBLE BEFORE REMOVING SHIPPING BRACES, SKIDS, OR ROLLERS. NOTE: TtKSE REFRIGERATORS WERE LINED UP AT FACTORY & NUIIBERED. IKSURE THEY ARE LINED up IN THE FIELD BY TtiE SAME SEQUENCE NUMBER. (THE NUMBER IS LOCATED ON THE HANDRAIL).

2. REMOVE SKIDS AND SHIPPING BRACES. INSTALL APPROX. A 5/16" BEAD OF SEALER AT ONE END OF CASE AS NOTED BY HEAVY LINE ON CROSS-SECTION.

3. MOVE CASES AS CLOSE TOGETHER AS POSSIBLE & LEVEL BY USING THE SHIM! PROVIDED. (CASES MUST BE LEVELED FROM FRONT TO BACK & END TO END).

4. REM&/E ACCESS COVERS OVER LINE-UP HOLES & INSERT THE SMALL T-NUTS IN THE END FRAME, BOTH FRONT & BACK. DISCHARGE GRILLE MUST BE REMOVED FOR ACCESS TO LINE HOLES IN TOP REAR OF CASES. PLACE THE!- SPECIAL T-NUT WASHER ON THE 3/8" MCHN BOLT WITH HOLLOW SECTION AEIAY FROM THE BOLT HEAD. ROTATE THE 3/8" BOLTS WITH W/T-NUT WASHER INTO THE T-NUTS ALTERNATELY UNTIL CASES ARE PULLED UP TIGHT s THE JOINT IS COKPLETELY SEALED. (REASONABLE CARE SHOULD BE EXERCISED IN THIS PROCEDURE TO PREVENT END FRAME DISTORTION). ASSIST PULLING CASE UP TIGHT BY BUMPING FROII OPPOSITE END OF CASE OR 8Y USING PRY BAR. AFTER CASES ARE PULLED UP TIGHT, IT MAY BE NECESSARY TO SLIGHTLY LOOSEN THE LINE-UP BOLTS IN THE RETURN AIR DUCT SO THAT THE RETURN AIR PArdELS HILL FIT OVER KEY HOLE SLOTS.

5. INSFECT JOINT FOR PROPER AIR AND WATER TIGHT SEAL BOTH INSIDE AND OUTSIDE THE CASE.

6, REPLACE LINE-UP ACCESS COVER PLUGS, PLATES, & DISCHARGE GRILLE.

JOINT TRIM - i?OST JOINT TRIM CAN & SHOULD BE INSTALLED If+:EDIATELY AFTERiS ARE LINED UP. WHERE POSSIBLE, INSTALL ALL TRIM IM!{EDI- ATELY SO IT WILL NOT BE LOST. THE TRIM THAT CANNOT BE INSTALLED IpillEDIATELY SUCH AS KICKPLATE AREA, STORE IN A SAFE PLACE UNTIL REFRIGERATION AND ELECTRICAL FIORK IS COKPLETED.

7 . "F" COLaRBAND JOINT TRIM - FASTEu COLORBAND JOINT TRIM "F" WITH (2) kZlB12-17 IN UP?ER HOLES FIRST, THEN (2) ;21B12-]g IN LO\;'ER HOLES,

8 . uG" TOP CAP JOIKT TRIM - HOCK TOP CAP TRIM OVER FP,ONT EDGE OF TOP

h

CAP & PUSH REAR DOb?i UNTIL TRI14 COKES INTO LINE. FASTEN WITH ;ZlBlZ-17 SMS,

9 . "E" REAR BAFFLE JOINT TRIM - POSITION TRIM & FASTEN WITH (4) #8X5/8 SMS.

10 . "H" JOINT DRIP CHAWEL - JOINT DRIP CHANNEL SEALS THE GAP CREATED BY JOINING OF THE TWO END FRAMES. CEpiTER THE CHANNEL & SLIP OVER THE FRAME.

11 . 11 B", & II ::I FRONT PANEL TRIM - LOWER TRIM "B" MUST BE INSTALLED FIRST. LOCATE IT & FASTEN WITH (2) #8X5/8 SMS. PLACE UPPER TRIM "C" IN PLACE AND INSTALL (4) #8X5/8 SMS.

12 l *ID" KIKCPLATE JOINT TRIM - POSITION & FASTEN WITH (2) $10.16X1/2 3%.

4 J

I

KIT

IJO.

I &y

?ZL-

~ ,c

Nl

4A

- rv

<c/:

KIT

NO.

SW/S

-4

625

4)X

/3-5

x ;

b-v’

\ eG

/VIm

R

c 0

s4.q

13

-4

E5

% #A

/3-5

22

1 86

iJSH

ED

BRIG

HT

ITEM

1

DES

CR

IPTI

ON

PA

RT

NO

. PA

RT

NO

. :

CIT

Y. ,

I .

I I

I I

I 1

I I

I

1 1

I I

.--Y

e”

- ..

- .

. .

. .

-

-w

/ --

. -

.--

* -

-

___I

_ -.

--.

. v

. #

--

c-

. _

. T

‘,‘-

.e-

. -.

- -

.--

. .

.--

\.

w--

---

- .

we

. .

-w.

--.

--

- c

*.--

.

- c

....

-.-

*e

.

I P3

CT I

.

. .

: .

.

2 .

A---l

A .

- c

.

I I

I -

- t--

----II

a- . - . - . - - - p - - - ^ -we- - - . - - - - - - f - - L - - - - -

r\rOTES --

1. MOVE REFRIGERATORS AS NE%? THEIR PEEI%~iENT LOCATION AS PO&E BEFORE REKOVIPr’G StiIPPIriG CRACES, SKIDS, OR ROLLERS. NOTE: THESE REFRIGERATORS \JERE LItjEll UP AT FACTORY & r:U!<BERED. INSURE THEY ARE tICED up IN THE FIELD BY THE SAME SEQUEijCE NUMBER. ' NUMCER IS LOCATED Ofi THE HANDRAIL).

(TtlE

2. REMOVE SKIDS AND SHIPPING BRACES. INSTALL APPROX. A 5/16" BEAD OF SEALER AT O&E END OF CASE AS NOTED BY HEAVY LINE ON CROSS-SECTION.

3. MOVI.. CASI* s AS Cl ox 7 o~x.Il~t 1: AS I'WS I P,LI: Pi I l.VT:I, f{Y USING I IIC SHIM PROVIDCD. (CASES MUST BE l.t'!ELED FROM FRONT TO BACK & END TO END).

4. REMOVE ACCESS COVERS OVER LINE-UP HOLES & 1::SERT THE SMALL T-NUTS IN THE END FRAME, BOTH FROi\IT & BACK. DISCHARGE GRILLE MUST BE REMOVED FOR ACCESS TO LINE HOLES IN TOP REAR OF CASES. PLACE THE- SPECIAL T-NUT WASHER ON THE 3/8" MCHN BOLT WITH HOLLOW SECTION AldAY FROM THE BOLT HEAD. ROTATE THE 3/8" BOLTS WITH b//T-NUT WASHER INTO THE T-NUTS ALTERNATELY UNTIL CASES ARE PULLED UP TIGHT & TiiE JOINT IS CCZPLETELY SEALED. (RE.&SO#BLE CARE SHOULD BE EXERCISED IN THIS PROCEDURE TO PREVEi4T END FRAfdE DISTORTION). ASSIST PULLIp!G CASE UP TIGHT BY 6UMPil"lG FROZ OPPOSITE Ep!D OF CASE OR BY USING PRY BAR. AFTER CASES ARE PULLED UP TIGHT, IT MAY BE NECESSARY TO SLIGHTLY LOOSEN THE LINE-UP GOLTS IN THE RETURN AIR DUCT SO TtjAT THE RETURN AIR PA?{ELS WILL FIT OVER KEY HOLE SLOTS. .

5. INSPECT JOINT FOR PROPER AIR AriD I;'kTER TIGHT SEAL EOTH INS-IDE AND OUTSIDE THE CASE.

6. REPLACE LINE-UP ACCESS CG'!EZ PLUGS, ?LATES, & DISCHARGE GRILLE.

JOINT TRIM --p-w- - MOST JOINT TRIbi CXl & Si-iGULD BE IiZTALLEO ii+;EDIATELY AFTkR CASES ARE LINED UP. i ;!t-(ERE PCSS I BLE, INSTALL ALL TRIl'rl I;:XEDI- ATELY SO IT WILL NOT BE LOST. THE TRIM THAT CAZtOT BE INSTALLED IMMEDIATELY SUCH AS KICKPLATE AREA, STORE IN A SAFE PLACE UNTIL REFRIGERATION AND ELECTRICAL \!CRK IS COi:PLETED,

7. "H" CCLORBAND JOINT TRIM - FASTE'4 COLORGNID JOINT TRIM NTH (2) #21B12'-17 IN UFPER HOLES, THEN (2) ?21812-79 IN LObIER HOLES.

8 . "E" CANOPY JOINT TRIM - HGCK LG!bIER EDGE OF CA:iOPY JOI:jT TRI!j INTO P-P- PLACE & PUSH TO THE REAR. FASTEN b!ITH (4) :8X3/4 SMS.

I

9 . "G" REAR BAFFLE JOINT TRI:l - PGSITIGTI TRI;.? & FASTEN !a!ITH (4) $8X5/8SMS.

10 . lJIt* JOINT DRIP CHAI'iNEL - JOiZT DRIP CLJq"l" ui\wEL SEALS THE GAP CREATED BY 'mNING OF ThE TWO END FRAKES. CENTER THE CHAN?lEL & SLIP OVER THE FRA;-1E.

11 . l'Blf & "C" FRONT PANEL TRIM - LOhER TRI:l "B" IaSUST BE INSTALLED FIRST LOClAfE IT AND FASTEN WITH (2) 28X5/8 SK. PLACE UPPER TRIM "C" IN . PLACE AND INSTALL (4) ,"SXs/S SF%.

12 * 'ID" KICKPLATE JOINT TRIM - POSITIG! & FASTEi4 IdITH (2) :lO-16%1/2 SMS.

0

IN THE CONSTANT EFFORT TO IMPROVE OUR PRODUCTS. WE RESERVE THE RIGHT TO CHANGE AT ANY TIME SPECIFICATIONS, DESIGN, OR PRICES WITHOUT INCURRING OBLIGATION.

OWlSiON OF KYSOR INDUSTRIAL CORPORATION

P.O. Box c 1600 Industrial 6lvd. Conyers, Georgia 30207 404 4834600

ONE-YEAR WARRANTY KYSORWARREN warrants to the original purchaser this new equipment and all parts thereof, to be free from defects in material and workmanship under normal use and service. If any part or parts of the equipment should prove defective during the period of one year from installation date (not to exceed one year and thirty days from the date of original shipment from the factory), KYSORWARREN hereby guarantees to replace or repair, without charge (F.O.B. CONYERS, GEORGIA), such part or parts as prove defective, and which KYSORIWARREN’s examination discloses to its satisfaction to be thus defective, with a new or functionally operative part. The liability of KYSORCWARREN under this warranty shall be limited to claims made by the original purchaser to KYSORIWARREN or its local distributor within the warranty period.

GLAZING; Glass is not guaranteed against breakage. If this refrigerator is equipped with a glazing assembly carrying the manufacturer’s brand name (Thermopane, Twindow, etc.), the manufacturer’s glazing warranty in effect at the time of this shipment is extended to that assembly. It is void outside the continential United States.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, IN- CLUDING, BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS, AND ALL OTHER OBLIGATIONS OR LIABILITIES OF KYSORWARREN.

THIS WARRAANTY SHALL NOT APPLY:

4.

5.

6.

7.

To the condensing unit used with refrigerated equipment unless same was sold and shipped by KYSORMARREN.

When this equipment or any part thereof is damaged by fire, flood, act of God, or when the original model and serial- number plate has been altered, defaced, or removed.

When this equipment or any part thereof is subject to accident, alteration. abuse, misuse, tampering, operation on low or improper voltages, or is put to a use other than recommended by KYSORAMRREN.

When this equipment or anv part thereof is damaged, or when operation is impaired, due to failure to follow installa- tion manual &iproper insiallation is the responsibility of the installer>.

Outside the continental United States.

To labor cost for replacement of parts, or for freight or shipping expenses.

If the Warranty holder fails to comply with all the provisions, terms and conditions of this Warranty.

Parts replaced under this Warrantv a, ~0 warranted only through the remainder of the original Warranty. KYSOR/ WARREN may, at its option and in its discretion, elect to honor this Warranty and to disregard the original purchaser’s noncompliance with any of the provisions. terms and conditions of this Warranty.

THIS WARR4NTY DOES XOT COVER CONSEQUEXTIXL DA>L\GES.

KYSORWARREN shall not be liable under any circumstances for anv consequential damages, including loss of profits, additional labor costs, loss of refrigerant or food products, or injury to person or property caused by defective material or parts or for any delay in the performance of chi ‘s Warranty due to causes beyond its control. The foregoing shall con- stitute the sole and exclusive remedy of any purchaser and the sole and exclusive liability of KYSORWARREX in con- nection with this product.