MVGR College of Engineering IT WORKSHOP

Dept. of CSE

Task 3 Every student should individually install windows XP on the personal computer. Lab

instructor should verify the installation and follow it up with a Viva

Install Options with Various Windows XP Disks

If your computer came with a disc (or set of disks) labeled as "Recovery" or "Restore...", do the

following:

1. Insert disc 1.

2. Power off the computer, and restart it. The manufacturer's recovery/restore program should

start automatically. If the application does not load automatically, and attempts to boot

into Windows instead, you will need to adjust the boot settings in your system's BIOS.

See Part 3: Configure Your Computer to Boot from CD.

3. Follow the on-screen instructions.

If your computer came with a Windows XP CD, see Part 4: Manual Install of Windows XP.

If you did not receive any disks with your system:

1. Some manufacturers (most notably HP and Compaq) have shipped some systems with the

recovery utility in a separate partition on the computer's hard drive. While the computer

boots, watch carefully for a briefly displayed message indicating what key to press in

order to access the recovery application. Press the indicated key. Consult your computer's

documentation for any information regarding recovery or restoration of the operating

system.

2. Some manufacturers (most notably Sony and Toshiba) require the owner to create their

own recovery/restoration discs for certain models.

o Click on the Start button , All Programs, and look for "PowerQuest Drive Image,"

"Recovery Wizard," or something similar.

o Follow the instructions to create the discs.

o After the discs have been created, follow the above instructions for running the

recovery/restore.

3. If your system does not have a built-in recovery utility, and you cannot make (or cannot

find) discs, you may contact the manufacturer to purchase the restore/recovery utility.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

Alternatively, you may purchase a full copy of Windows XP and follow Part 4: Manual

Install of Windows XP.

Part 3: Configure Your Computer to Boot from CD

1. While the computer boots, watch carefully for a briefly displayed message indicating what

key to press to enter setup. Press the indicated key and proceed to step 2. If you cannot

determine which key to press try the following:

o Check your computer's documentation for information on accessing your system's

BIOS or CMOS settings.

o The most commonly used keys are F1, F2, F10, Delete, and Escape. Try pressing

each of these keys individually on the screens which appear before the Windows

logo is displayed.

o Contact your computer's manufacturer.

2. Find the option with a name such as "Boot Devices" or "Boot Order." The exact name and

location will vary by manufacturer.

3. Reconfigure the options so that the computer will boot from CD before attempting to boot

from the hard drive. Again, the exact procedure will vary by manufacturer. Contact the

manufacturer for assistance, if needed.

Part 4: Manual Install of Windows XP

1. Disconnect the network cable from your computer.

2. Turn on the computer.

3. Insert the Windows XP CD into the drive.

4. When you receive the prompt to Press any key to boot from CD..., press any key to boot

from the Windows CD.

5. Wait while the Windows setup files are loaded.

6. When presented with the following menu, press Enter to begin the Windows XP setup.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

7. After reading the License Agreement, press F8 to accept it and continue the installation.

8. You will now see a list of the partitions on your hard drives. Use the cursor keys to select an item not labeled as unpartitioned space.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

9. Press the D key to delete the selected partition. If you receive the following prompt, press Enter to continue. Otherwise, proceed to the next step.

10. Press the L key to confirm the deletion.

11. Repeat steps 8-10 until all space is labeled as unpartitioned.

12. Use the cursor keys to select an unpartitioned space. Press the C key to create a new

partition.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

13. When prompted for the size of the partition, press Enter to accept the default

recommendation.

14. Repeat steps 12 and 13 for each unpartitioned space with a size greater than 8 MB.

15. Upon returning to the partition list, select the item labeled as “ C: Partition1 [New

(Raw)]” and press Enter.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

16. At the following prompt, select the option to Format the drive using the NTFS file system.

Press Enter to continue.

17. The setup program will now proceed to format the drive. This may take a while depending on

the size of the drive.

18. Once the format procedure has completed, files should begin to be automatically copied from

the installation CD

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

19. Once all

necessary files have been copied, the system will be automatically restarted. You may now

remove the CD. If you choose to leave the CD in the drive, do not press any key when

prompted to press any key to boot from CD.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

20. The Windows setup program will now complete the installation. The content and appearance

of the remaining screens may differ based on the exact version and distribution of Windows

XP you are installing.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

21. The default settings on this screen should be correct for the U.S. Click Next.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

22. Enter your name and, optionally, your organization. Click Next.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

23. Enter the Windows XP product key and click Next. For help finding your product key, see

the note at the beginning of this document.

24. Enter a name for the computer. This may be anything you like. In Windows XP Professional

you will be prompted to enter an administrator password. Do not leave any of your system

passwords blank! For security purposes, it is recommended you choose a password that

contains mixed case letters, numbers and symbols, and is not based on a dictionary word.

Click Next.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

25. Set the date, time, and time zone to +5.30 GMT (IST) Click Next.

If your Network card is identified by windows XP the following screens maybe

displayed. Otherwise we may get the Display Settings screen. (Step 29.)

26. Setup will scan for a network. If you receive the following prompt, select Typical Settings

and click Next.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

27. If you are prompted for workgroup or domain settings, leave the default entries and click

Next.

28. Setup will continue and will eventually reboot. If you have left the CD in the drive, do not

press any key when prompted to press any key to boot from CD.

29. After rebooting, you may see a display settings box. If you do, click OK. The screen may flicker for a moment and ask you whether you can see the image. If you can, click Yes.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

30. When you see the welcome screen, click Next.

31. If you are asked to setup a network or Internet connection at this time, click on Skip.

32. You will now be prompted to register your copy of Windows. Since we have not

connected to the network yet, select No and click Next. If prompted to activate Windows,

choose the appropriate option to skip this step as well. Windows will prompt you to do

this later if it is required.

MVGR College of Engineering IT WORKSHOP

Dept. of CSE

33. Click Finish on the Thank You screen. The Windows XP operating system itself should now

be installed.

34. Desktop for the xp after installation.