fornax ip66 50/60hz · 2019. 8. 14. · fornax. 51-40/b 2 10 8 9 7 click ip66 230v 50/60hz l n 8-9...
TRANSCRIPT
-
1
1 2
2x
612mm - 6x1172mm - 10x1452mm - 12x2x
2x
2x
2x
≥ 150 mm
≥ 150 mm
IP66230V
50/60Hz
2x
3
Cable gland PG 13,5 for wires Ø 6 - 12mm
4
Click
90°5 6A
Click
1
2
Ø max. 10mmØ max. 10mm≤ Ø10 mm
6B 6C
A [mm] D [mm]
612 475
1172 700
1452 940
A145
111
100
D
4x+
FORNAX
-
251-40/B
10
8
9
7
Click
IP66230V
50/60Hz
L N
8-9 mm
1,5–2,5 mm 2
21
Click
Click
3
11
Always close the clips symmetrically from the middle to the sides of the lamp!
Always close up both opposite clips at once
12Don‘t open when the luminaire is alive!
Installation can only be carried out by an authorized person and according to the mounting instructions. Any other installation is considered to be improper. For well installation and good luminaire work is necessary ensure a planarity of a mounting surface. Make sure that the luminaire is always disconnected from the power supply before the installation work. Do not use the luminaire if damaged or if damaged the power cable. Only damp micro�ber cloth can be used for cleaning. technical changes are subjected without notice. Do not dispose the luminaire or its parts as household waste, but make the proper recycling.
The light source in this luminaire may be replaced only by the manufacturer or its contractual service technician or similarly quali�ed person!
612mm 2600 32 50 52 85612mm 3200 4400 10 16 16 261172mm 5200 6400 8800 10 16 16 26
1452mm 6500 8000 11000
∑lm ∑lm ∑lm
16A B 10A C 16A C 10A B
1172mm10 16 16 26
1452mm
12800
16000
11
11
18
18
18
18
30
30
Table of maximal number of luminaires in one lineLength
∑ luminaires
∑ luminaires
∑ luminaires
∑ luminaires
FORNAX
-
Zero-crossing
point operation
K
Automatic switching based on motion and light level.
Zero-crossing point operation helps protect the sensor
against in-rush current.
Super Compact size makes it suitable to fix within most
luminaires.
4-pole press-in terminal (L, N, N, L'), easy assembly.
Detection area, time delay and daylight threshold can
be precisely set via DIP switch.
Wide detection area, range up to 12m in diameter.
Introduction
MC030S E is an innovative and active motion detector
with HF system 5.8GHz. Motion can be detected through
plastic, glass and thin non-metal materials.
The sensor supplies a simple energy-saving solution to
use l ight only when and where you need i t . I t
automatically switches on/off light based on motion and
ambient light level. Can control all kinds of lamps, for
example, halogen, fluorescent and LED lights. Compact
size and small casing, suitable to fix within most
luminaires. 4-pole press-in terminal (L, N, N, L'), very
easy to install.
The high qual i ty relay is part icular ly suitable for
commercial use with switching power up to 400W for
LEDs and fluorescent lamps and up to 800W for
incandescent lamps.
MC030S EON-OFF Function / Smart Version
Light SensorMax.6M Hold Time 5s~30min
AutomaticOn/Off
6m
Mounting Height 6m Max.
555 Years
Guarantee
Years Guarantee
ON/OFF
-
ON -OFF Function
Motion sensor MC030S E + LED driver or ballast (Any brand)
MC030S E is an innovative motion sensor, switch on the light on detection of movement, and switch off after a hold time when there is no motion detected. As built-in daylight sensor can read brightness value, the sensor does not switch on the light if with sufficient natural light.
Wiring scheme
Detection Pattern
With sufficient light, the lamp doesn't switch on.
After hold time, the sensor switches off the lamp when no motion is detected.
1 2 3
10%
25%50%
75%
100%
Ceiling mounting pattern (Unit: m)Suggested installation height: 3m
Wall mounting pattern (Unit: m)Suggested installation height: 1.5m
0
2
4
8
6
2
4
6
8
10 12 14
10
12
14
10
12
14
With insufficient ambient light, the sensor switches on the lampwhen motion is detected.
10%25%
50%
75%
100%
L N
L N
Control gear
Max. 400W
L LN N
Control gear Control gear
-
MC030S EOperating voltage 220~240Vac, 50Hz
Rated load 400W(inductive), 800W (resistive)
HF system 5.8GHz±75MHz, ISM wave band
Transmitting power